1. Quick description before we start wiring the INTERFACE (PESWIAKJ, PESWIPS, PESWIX,
PESWIECL). All modules wire up the same, only programming will be differient.
The INTERFACE's wire color we are going to use is White. This is the White wire on the INTERFACE,
not the vehicle!
The other wires on the INTERFACE, green, yellow, orange and blue wires are not used for your
2007 Ford Explorer Sport Trac .
This leaves you with a Red, Black and two loop wires. These wires will be discussed down below.
note: SWC = steering wheel control
2. Picture of the Ford Explorer plug and prepping module for installation.
The connector is viewed from the pin side not wire side.
Page 1 of 3
3. Connecting the INTERFACE's SWC input wire to vehicle plug.
1.
Connect the INTERFACE's White wire to...18 Gray/Yellow of the above
connector
2.
Cut the purple loop then connect a 100 ohm resistor to the second purple
wire, cap off the first(outside edge)purple wire. Connect other en d of
resistor to the white wire. The white wire also connects to pin 18 in the
car. Connect p in 19 Blue/White wire to ground.
4. Connecting power and ground wires.
Black wire: Connect the INTERFACE's black wire to chassis ground. This is usually
a black wire on the aftermarket wire harness.
Red wire: Connect the INTERFACE's red wire to a switched +12volt wire. This is
usually a red wire on the aftermarket wire harness.
Using an aftermarket wire harness ( http://bestkits.com/ ) will reduce any potential
problems. Wire harnesses can be purchased from local stereo shops. Please note
that aftermarket wire harnesses do not have a wire in the SWC pin location we
mention above. You still have to connect the INTERFACE's White wire to the wire
on the factory side of plug.
5. Instructions for cutting or not cutting loop wires.
Step A: Cut the Purple loop wire in half and insulate outside end.
Step B: The brown loop wire does not need to be cut.
6. Programming the INTERFACE with a version number and 'IR' Mode.
The INTERFACE has to be programmed for version # 9 and set for 'Standard IR' Mode.
1.
Press and hold the 'Mode' button on the INTERFACE while turning on the
vehicle to the accessory position. Both LED's will turn on.
2.
Release the 'Mode' button and both LED's will turn off and then they will
turn on for 3 seconds. Wait for 3 seconds and bo th LED's will turn off.
3.
Press the 'Mode' button 9 times. Each time you press and release the 'Mode'
button, both LED's will turn on and off. Once you press the "Mode" button 9
times, wait for 3 seconds. The right LED will flash 9 times indicating it is
programmed for version 9. If it flashes the wrong version number, you will have
to start all over at step 1 above in this section. Turn the key off.
Once you have programmed the correct version number, you will not have to
do these steps again. If you need to reprogram the SWC and wireless remote
functions, you can go directly to the next section.
4.
7. Programming the INTERFACE to learn SWC and wireless remote functions.
1.
Turn the key to the accessory position (you do not need to hold the ‘Mode’
button at this time). The right LED will flash 9 times. This indicates it is
programmed for version 9.
2.
Press the 'Mode' button until the LEFT LED turns on, then release the
button (This will erase all previous learned SWC and wireless remote functions)
Page 2 of 3
The INTERFACE is now ready to learn a command from the steering wheel.
3.
Press the Volume UP button on the steering wheel and hold the button. Wait until
the LEFT LED turns off before you release the button. Note: Please do not press and
release the steering wheel button quickly! If you do not press any buttons on the
steering wheel, the INTERFACE will time out after 7 seconds, which will turn off the
LEFT LED and end programming. If you missed some buttons, you will have to start
all over and program from the first button. If the LEFT LED turns off and goes to the
right LED without pressing the steering wheel buttons, then there is a wiring issue
4.
The right LED will turn on at this time, waiting to learn from the wireless remote.
Note: You do not have a timeout period when the RIGHT LED is on. You can take
your time here. However,make sure there is no fluorescent lights or sunlight in
sight of the INTERFACE other wise the RIGHT LED will turn off and go to the
LEFT LED.
5.
Press and hold the wireless remote Volume UP button while pointing the remote
towards the INTERFACE's IR input. Wait until the RIGHT LED turns off before you
release the button.
6.
The LEFT LED will turn on.
7.
From here you will do steps 3 through 6 again for each additional button to be
So the next steering wheel button should be Volume DOWN and the wireless remote
Volume DOWN. Note: The steering wheel buttons can be assigned any wireless remote
function. So if you have for example a 'Mode' button on the steering wheel, you can
program it a 'Mute' function from the wireless remote.
8.
Once you finish programming the SWC buttons and wireless remote functions, the LEFT
LED should be on. Wait for 7 seconds and both LEDS will flash 3 times. This indicates
that the INTERFACE has exited programming. The INTERFACE's RIGHT LED will flash
9 times and will be in 'Run Mode'
9.
Cycle vehicles ignition (turn off then back on) and test unit (aim emitter at radio and
press button on Steering Wheel.
Page 3 of 3