ar y
n
i
im
prel
iC-MD EVAL MD1D
EVALUATION BOARD DESCRIPTION
Rev A2, Page 1/9
ORDERING INFORMATION
Type
Order Designation
Evaluation Board
iC-MD EVAL MD1D
Description Options
iC-MD Evaluation Board
ready to operate, accessible through GUI via PC adapter
Software
iC-MD GUI
GUI software for Windows PC
Device setup file generation, board configuration via adapter
For download link check www.ichaus.com/MD
PC Adapter
iC-MB3 ICSY MB3U-I2C
PC-USB Adapter with I2C/SPI extension cable
Download documentation at www.ichaus.com/tools
BOARD MD1D
(size 80 mm x 100 mm)
Figure 1: Component side
Copyright © 2014 iC-Haus
TERMINAL DESCRIPTION
VB
V3.3
V5
VDD
GND
+10 to +20 V Supply Voltage
+3.3 V Supply Voltage
+5 V Supply Voltage
Selected iC-MD Supply Voltage
0 V Ground
AP
AN
BP
BN
CP
CN
TPI
Incremental Input AP
Incremental Input AN
Incremental Input BP
Incremental Input BN
Incremental Input CP
Incremental Input CN
Touch Probe Input
ACT1
ACT2
NERR
NWARN
Actuator 1 Output
Actuator 2 Output
Error Input/Output (active low)
Warning Input/Output (active low)
SPI
SPI Interface Connector
MA
SLO
SLI
D3
Clock Input Interface BiSS/SSI
Data Output Interface BiSS/SSI
Data Input Interface BiSS/SSI
Supply Indicator LED
http://www.ichaus.com
ar y
n
i
im
prel
iC-MD EVAL MD1D
EVALUATION BOARD DESCRIPTION
Rev A2, Page 2/9
RELATED DOCUMENTS
• IC Documentation
→ http://www.ichaus.com/MD
• PC-USB Adapter Description
→ http://www.ichaus.com/MB3U_MB3U-I2C_datasheet_en
• GUI software for Windows PC: check here for download links
→ http://www.ichaus.com/MD
CONNECTOR AND TERMINAL PINOUT
9-pin Sub D Connector J1 - male
PIN
Name
Function
1
VB
+12 V Supply Voltage
2
MAO +
Master Clock Output
3
MAO Master Clock Output (inverted)
4
VDD
+5 V Supply Voltage
5
SLO Data Output (inverted)
6
GND
0 V Ground
7
SL +
Slave Data
8
SL Slave Data (inverted)
9
SLO +
Data Output
9-pin Sub D Connector J4 - female
PIN
Name
Function
1
VB
+12 V Supply Voltage
2
MA +
Master Clock Input
3
MA Master Clock Input (inverted)
4
VDD
+5 V Supply Voltage
5
SLI Data Input Line (inverted)
6
GND
0 V Ground
7
SL +
Slave Data
8
SL Slave Data (inverted)
9
SLI +
Data Input Line
2-pin Terminal J5- Power Supply Input
PIN
Name
Function
1
VDD
+3.3 . . . +5 V Supply Voltage
2
GND
0 V Ground
10-pin Adapter Connector J6 - male
(to SPI Master)
PIN
Name
Function
1
SCL
Serial Clock Line
2
GND
0 V Ground
3
Reserved 4
+5V
+5 V Supply Voltage
5
Reserved 6
Reserved 7
MOSI
Serial Data Line
8
Reserved 9
MISO
Serial Data Line
10
GND
0 V Ground
Connector for USB Adapter MB3U-I2C
The board features one 10-pin connectors for serial
SPI communication. The PC-USB Adapter iC-MB3 iCSY MB3U-I2C enables the evaluation board to be connected to a common Windows PC via SPI interface.
iC-MD software can be used to access the board from
a Windows PC (see section "APPLICATION SOFTWARE" for more details).
Note : Please install the latest USB driver before you
attach the PC Adapter to the PC.
iC-MD EVAL MD1D
EVALUATION BOARD DESCRIPTION
ar y
n
i
im
prel
Rev A2, Page 3/9
JUMPER DESCRIPTION
JP1, JP2: BiSS Onboard Loopback
2-pin jumper terminal male
PIN
Name
BiSS Bus Structure
X
BiSS Start of Bus, Point-To-Point
Function
BiSS IN to BiSS OUT
Loopback of SLO to SL
JP3: 5 V Power Supply
2-pin jumper terminal male
PIN
Name
No Direct 5 V
X
5 V Direct Supply
Function
JP4: VB Power Supply
2-pin jumper terminal male
PIN
Name
No VB Supply
X
VB Supply
Function
JP5, JP6: RJ45 Shield to GND
2-pin jumper terminal male
PIN
Name
No RJ45 Shield to GND
X
RJ45 Shield to GND
Function
+5 V Direct Board Supply
Supply of +10 to +20 V Required to Board Terminals VB and
GND
RJ45 BiSS Connector IN / OUT Shield to GND
JP7: 5 V Adapter Power Supply
2-pin jumper terminal male
PIN
Name
No 5 V Adapter Supply
X
5V Adapter Supply
Function
No direct +5 V Adapter Supply
+5V Direct
JP8: Enable TPI Button + Buffer
2-pin jumper terminal male
PIN
Name
TPI Button + Buffer Disabled
X
TPI Button + Buffer Enabled
Function
External TPI Operation
Manual TPI Operation Possible
JP9: 5 V Adapter Power Supply
3-pin jumper terminal male
PIN
Name
12
5 V Voltage Regulator Selection
23
3.3 V Voltage Regulator Selection
Function
On Board +5 V Supply
On Board 3.3 V Regulator Supply
CN
VDD
3
IFA-R3
1k
14
VDD
3
IFB-R3
1k
14
4.7k
3
IFC-R3
1k
14
IFC-R4
13
4
4.7k
15
IFC-R2
1k
IFC-R1
2
16
1
4.7k
IFB-R4
13
4
4.7k
15
IFB-R2
1k
IFB-R1
2
16
1
4.7k
IFA-R4
13
4
4.7k
15
IFA-R2
1k
IFA-R1
2
16
1
VDD
6
IFC-R6
1k
11
12
IFC-R5
1k
5
7
10
IFA-R7
7
10
IFC-R7
7
10
IFB-R7
VDD
6
IFB-R6
1k
11
12
IFB-R5
1k
5
VDD
6
IFA-R6
1k
11
12
IFA-R5
1k
5
VDD
8
9 IFC-C1
8
9 IFB-C1
8
9 IFA-C1
CP
BN
BP
AN
CN
AP
SPI
Figure 2: Circuit diagram including optional components
J6
9
J6
10
NCS
MISO
J6
8
VDD
CN
9
SCK
CP
8
BN
7
AN
5
BP
AP
4
6
TPI
20
MOSI
JP7
TPI
J6
7
J6
6
J6
5
J6
4
J6
3
J6
2
J6
1
TPI
U1
iC-MD
C6 1
100nF
2
JP8
17
VDD
VDD
GND
10
TPI
2
1
SLO
SLI
MA
AP
AN
BP
BN
CP
CN
3
MA
16
15
14
13
11
12
19
18
J7 1
J7 2
J7 3
J7 4
J7 5
J7 6
J7 7
J7 8
J7 9
J7 10
NCS
SCK
MOSI
MISO
OMR_B3S_1000
S1
SLI
SLO
NCS
SCK
MOSI
MISO
NERR
NWARN
ACT1
ACT0
C7
1nF
R1
10k
VDD
R7
560
V5
10
9
8
7
6
5
4
3
2
1
J8
J8
J8
J8
J8
J8
J8
J8
J8
J8
R6
560
D7
GN
V3_3
V5
V3_3
R2
opt
D6
GN
MA
SLI
SLO
3
3
2
2
U2-B
75179
U3-B
75179
MA
SLI
SLO
U3-A
75179
U2-A
75179
1
VCC
C5
U2-S
1μF 75179
GND
4
3 VOUT VIN 1
GND
2
NERR
NWARN
ACT1
ACT0
1
VCC
U3-S
75179
GND
4
C4
10μF
TPI
ACT1
ACT0
VDD
NCS
SCK
MOSI
MISO
NWARN
NERR
NERR
NWARN
ACT1
ACT0
D4
RD
VDD
R8
560
D5
OR
VDD
JP9
R9
560
1
2
3
6
5
6
5
7
8
7
8
D3
GN
R3
560
C3
10μF
R5
120
R4
120
SLO-
SLO+
MAO-
SLO-
SLO+
SL-
SL+
SLI-
SLI+
JP2
D-SUB 9
OUT
J1-SLO
9
J1-NSL
8
J1-SL
7
J1-GND
6
IN
J1-NSLO
5
J1-VDD
4
J1-NMAO
3
J1-MAO
2
J1-VB
1
J4-NSLI
5
J4-VDD
4
J4-NMA
3
J4-MA
2
J4-VB
1
J5 1
J5 2
GND
VB
JP4
D-SUB 9
VB
J4-SLI
9
J4-SL
7
J4-NSL
8
J4-GND
6
SL-
JP1
D1
BYS10-45
C1
330nF
VB1
SL+
U4
78M05
3 VOUT VIN 1
GND
4
MAO+
SLI-
SLI+
MA-
MA+
C2
100nF
V5
D2
BYS10-45
JP3
V5
MAO-
MAO+
VB
VDD_IN
MA-
MA+
VB_IN
VB_IN
VDD_IN
JP6
J2-VB
7
J2-S2
S2
SHIELD_OUT
J2-S1
S1
J2-GND1
B
J2-GND
8
J2-NMAO
6
VB
J2-NSLO
5
J2-SLO
4
J2-MAO
3
J2-NSL
2
J2-SL
1
J2-VB1
A
RJ45
OUT
J3-S2
S2
SHIELD_IN
J3-S1
S1
J3-GND1
B
J3-GND
8
J3-VB
7
J3-NMA
6
MAO-
SLO-
SLO+
MAO+
SL-
SL+
VB
JP5
VB_IN
MA-
J3-NSLI
5
J3-MA
3
J3-SLI
4
MA+
SLI+
SLI-
J3-NSL
2
J3-SL
1
J3-VB1
A
SL-
SL+
VB_IN
RJ45
IN
EVALUATION BOARD DESCRIPTION
CP
BN
BP
AN
AP
GND1
REGISTERS
VDD
I/O-INTERFACE
VDD
VDD
MUX & COUNTER
U5
LT1963A33
iC-MD EVAL MD1D
ar y
n
i
im
prel
Rev A2, Page 4/9
CIRCUIT DESCRIPTION
iC-MD EVAL MD1D
EVALUATION BOARD DESCRIPTION
ar y
n
i
im
prel
Rev A2, Page 5/9
ASSEMBLY PART LIST
Device
C1
C2, C6
C3, C4
C7, C5
J1
J2, J3
Value (typical)
330nF
100nF
10uF
1uF
D-SUB9-M 90°
RJ45_10
YAMAICHI_RJ45_10_YCONJACK-21
J4
D-SUB9-F 90°
J5
AKL59 02
J6
WSL10
U1
iC-MD TSSOP20
U2, U3
75LBC179 SO8
U4
78M05 DPAK
U5
LT1963A33 SOT223-4
JP1, JP2, JP3, JP4 SLLP1097 2G
JP5, JP6, JP7, JP8, SLLP1097 3G
JP9
GND, VB
LBS02
D1, D2
BYS10-45
D3
LS-T670 green
D4
LS-T670 red
D5
LO-T67K orange
D6, D7
LS-T670 green
R1, R2
10k
R4, R5
120
R3, R6, R7, R8, R9 562
IFA, IFB, IFC
DIL16
ACT0, ACT1, AN, S1-F
AP, BN, BP, CN, CP,
GND1, MA, NERR,
NWARN, SLI, SLO,
TPI, V3_3, V5, VDD
S1
OMR_B3S_1000
OMRON_B3S_1000
J7, J8
MK0110G
RF1, RF2, RF3, RF4 Rubber foot
Comment
Supply backup capacitor
Supply backup capacitor
Supply backup capacitor
Supply backup capacitor
BiSS interface connector
BiSS interface connector (not mounted)
BiSS interface connector
Supply connector
SPI interface connector
iC-MD or mounted DIL PCB with iC-MD
RS422 transceiver
5 V supply
3.3 V supply
2-pin jumper terminal
2-pin/3-pin jumper terminal
Supply connector
Protective diodes
LED 5 V
LED NERR
LED NWARN
LED ACT1 + 2
TPI resistor
RS422 terminator
LED resistor
Input filter system
Pin
TPI button switch
Connection to DIL28 iC-MD adapter
iC-MD EVAL MD1D
EVALUATION BOARD DESCRIPTION
ar y
n
i
im
prel
Rev A2, Page 6/9
EVALUATION SOFTWARE
iC-MD software for PCs running on Windows operating systems as well as the required USB driver are available
as a ZIP file. iC-Haus software built with LabVIEW™ requires the installation of the LabVIEW™ Run-Time Engine
(RTE). The RTE must be installed only once, hence there are two download links available.
Software overview online: http://www.ichaus.com/software
Download package
iC-MD:
without RTE (small size)
http://www.ichaus.com/MD_gui
including RTE (big size)
http://www.ichaus.com/MD_gui_rte
Features
•
•
•
•
IC configuration made easy by parameter tables and tool tips
Editing of application-specific default setups (*.hex)
Access to DUT and transfer of setup data to RAM
Storage of IC setups as Intel Hex file for programming devices
Installation
After unzipping the "MD1SO_gui_xxrte.zip", the following files are located in the selected directory.
(xx is a placeholder for the software revision, e.g. B1 )
→ "setup.exe"
→ "USB_MB3U_driver_ftdiyyyyy.exe"
(yyyyy is a placeholder for the driver revision, e.g. 20600)
Note : Administrator rights are required to run installations.
1. The installation of the software starts by executing the "setup.exe" installation package in the folder
"MD1SO_gui_xxrte".
→ Follow the on-screen instructions to finish the installation procedure.
2. USB driver need to be installed to access the evaluation board via the PC Adapter.
→ Execute the "USB_MB3U_driver_ftdiyyyyy.exe" installation package and follow the on-screen instructions.
This process can take a few minutes.
3. Installation will make the software "MD1SO_gui_xx.exe" available in the selected working directory. The
execution of this file will start the software. Figure 3 shows a screenshot of the start up window.
iC-MD EVAL MD1D
EVALUATION BOARD DESCRIPTION
ar y
n
i
im
prel
Rev A2, Page 7/9
GUI Description
The GUI is divided into four sections:
•
•
•
•
1:
2:
3:
4:
Menu section
Header section
Parameter tables and control buttons
Status section with transcript window and online help window.
Figure 3: GUI start-up window
iC-MD EVAL MD1D
EVALUATION BOARD DESCRIPTION
ar y
n
i
im
prel
Rev A2, Page 8/9
Menu
Button
Description
1 Menu Section
<File>
Save Config File
Load Config File
Exit
Saves the configuration to a file, Intel Hex file format (*.hex).
Loads the configuration to the IC, Intel Hex file format (*.hex).
Quits the software.
<Interface>
No Hardware
Disconnects the board and resets the communication between PC
and adapter.
Selection for PC-USB adapter MB3U-I2C.
iC-Interface ↔
USB (MB3U SPI)
Interface Options
→ Connect & Read
<Extras>
Parameter Search
Generate Report
About
Checked: connects the PC adapter and reads the IC registers.
Unchecked: connects the PC adapter without reading the IC
registers.
Enables a search field to locate a parameter’s control field. If a name
match is found, the corresponding control field will be highlighted
and focused.
Generates a *report.zip archive reporting the current software status. This report eases debugging software issues by the iC-Haus’
support team.
GUI release information.
2 Header Section
Project title, software version, status and connection state.
3 Parameter Section
Parameter configuration, read/write access to IC.
<Tabs>
Configuration
Instructions
Error/Warning Monitor
Communication Control
Hex Editor
<Parameter> Read RAM
Write RAM
Write Immediately
Save Config
Load Config
4 Status Section
Refer to IC datasheet.
Refer to IC datasheet.
Refer to IC datasheet.
Refer to IC datasheet.
This tab is a different view of the IC’s register content in HEX format. Changes made are not automatically updated to the other tabs.
Push <Read RAM> to update the parameter tabs.
Reads all parameters from the IC and refreshes the display.
Writes all parameters from GUI to IC RAM.
If checked, any change to a parameter is transferred immediately.
If disabled, the GUI can be used stand-alone without hardware.
Reads all parameters from a file.
Writes all parameters to the a file.
Transcript and feedback messages of user actions.
The GUI software starts with <Interface> Disconnected.
When moving the mouse cursor accross an input box, a tooltip comes up and displays the real parameter name
according to this box. If a functional parameter description is required, please refer to the IC datasheet.
iC-MD EVAL MD1D
EVALUATION BOARD DESCRIPTION
ar y
n
i
im
prel
Rev A2, Page 9/9
REVISION HISTORY
Rel
Rel.Date
A1
10-01-28
Chapter
Modification
Page
Rel
Rel.Date
Chapter
Modification
Page
A2
14-10-22
ORDERING INFORMATION
Web links updated.
1
RELATED DOCUMENTS
Web links updated.
2
CONNECTOR AND TERMINAL
PINOUT
MB3U-I2C connection and supply added.
2
EVALUATION SOFTWARE
Standardized file names updated.
Web links updated.
GUI screenshots updated.
GUI description updated.
6, 8
First release.
iC-Haus expressly reserves the right to change its products and/or specifications. An info letter gives details as to any amendments and additions made to the
relevant current specifications on our internet website www.ichaus.de/infoletter; this letter is generated automatically and shall be sent to registered users by
email.
Copying – even as an excerpt – is only permitted with iC-Haus’ approval in writing and precise reference to source.
iC-Haus does not warrant the accuracy, completeness or timeliness of the specification and does not assume liability for any errors or omissions in these
materials.
The data specified is intended solely for the purpose of product description. No representations or warranties, either express or implied, of merchantability, fitness
for a particular purpose or of any other nature are made hereunder with respect to information/specification or the products to which information refers and no
guarantee with respect to compliance to the intended use is given. In particular, this also applies to the stated possible applications or areas of applications of
the product.
iC-Haus products are not designed for and must not be used in connection with any applications where the failure of such products would reasonably be expected
to result in significant personal injury or death (Safety-Critical Applications) without iC-Haus’ specific written consent. Safety-Critical Applications include, without
limitation, life support devices and systems. iC-Haus products are not designed nor intended for use in military or aerospace applications or environments or in
automotive applications unless specifically designated for such use by iC-Haus.
iC-Haus conveys no patent, copyright, mask work right or other trade mark right to this product. iC-Haus assumes no liability for any patent and/or other trade
mark rights of a third party resulting from processing or handling of the product and/or any other use of the product.