FIXTURE DEFINITIONS (INDIVIDUALS/ROWS/PATTERNS):
CRN
TO BE USED IN CONJUNCTION WITH FIXTURE DETAIL AND LAYOUT SHEETS
STEP 1: INSTALL FIXTURE STEP 2: PREPARE ACCESS COVER
L.END
1
SPLICE
PAT
BALLAST
CHANNEL
(EXPOSED BY
CUTOUT IN
HOUSING)
SPLICE
FIXTURE
FLANGE
PAT_L
WS)
(RO NDS)
.
P
TY . (I
/4" 4" TYP
1
3 3/
END
SHELL
EACH RECESSED UNIT IS FABRICATED WITH (4) 3/16" DIA.
HOLES (2 PER HANGER BRACKET) FOR ATTACHMENT
OF HOUSING TO ABOVE STRUCTURE BY
(BY OTHERS). 1. REMOVE K.O. IN ACCESS COVER 1 (SUPPLIED).
WIRE
1. RAISE FIXTURE & SECURE TO ABOVE STRUCTURE BY WIRE
(BY OTHERS).
2. SECURE GREENFIELD CONNECTOR (BY OTHERS) TO
ACCESS COVER.
STEP 5: CEILING INSTALLATION
R.END
IND
CRN = 2-WAY CORNER
IND = INDIVIDUAL FIXTURE
INT = INTERMEDIATE FIXTURE
INT_P = INTERMEDIATE PATTERN FIXTURE
L.END = LEFT END FIXTURE (TYPICAL FEED)
L.END_P = LEFT END PATTERN FIXTURE (TYPICAL FEED)
PAT = PATTERN FIXTURE
PAT_L = PATTERN LEFT FIXTURE
R.END = RIGHT END FIXTURE
R.END_P = RIGHT END PATTERN FIXTURE
INT_P
BOTTOM
FLANGE
DETAIL "A" - STRIPE SPLICE INSERTION
PREVIOUSLY
INSTALLED
FIXTURE
(PLAN VIEW)
SEE JOB LAYOUT FOR ROW PLACEMENT
CRN
2
GREENFIELD
CONNECTOR
(BY OTHERS)
CRN
INT
INT
HANGER
BRACKET
L.END_P
SPLICE
STEP 3: INSTALL COVER
STEP 4: JOINING (ROWS/PATTERNS) DETAIL "B" - FIXTURE JOINING
GROOVE
JOINING
FIXTURE
R.END_P
INSTALLATION SHEET FOR STRIPE 31/32 (STRP31/32) RECESSED FLANGELESS FIXTURE
SPLICE (SEE FIXT.
DEFINITIONS FOR
PLAN VIEW)
3
HANGER/
JOINER
BRACKET
CRN
1. RAISE FIXTURE & MAKE APPROPRIATE ELECTRICAL CONNECTIONS AT
JOINING SECTION.
2-WAY CORNER
1. MAKE ALL NECESSARY ELECTRICAL CONNECTIONS.
2. ATTACH ASSEMBLED ACCESS COVER 1 TO BALLAST CHANNEL
BY SLIDING BOTTOM FLANGE OF COVER UNDER TOP OF CHANNEL
& TOWARDS END SHELL.
3. SECURE ACCESS COVER 1 WITH 8-32 X 3/8" SELF-TAPPING
SCREWS 2 (1 PER COVER).
CRN
STEP 6: DIFFUSER INSTALLATION
DRYWALL SCREW
(BY OTHERS)
NOTE: JOIN FIXTURES SO THAT (2) SPLICES FROM PREVIOUSLY INSTALLED
FIXTURE SLIDE IN GROOVES OF JOINING FIXTURE AS SHOWN IN DETAIL
"A" ABOVE.
NOTE STRP31
: HOUSING USED
2. MATE JOINING BRACKETS AS SHOWN, & SECURE WITH (6) 8-32 X
3/8" MACHINE SCREWS 3 (SUPPLIED) & (6) 8-32 KEPS NUTS 4
(SUPPLIED) AT MATING HOLES (REFER TO DETAIL "B" ABOVE).
FOR ILLUSTRATION PURPOSES.
STRP32 INSTALLATION IS SIMILAR.
BALLAST ACCESS
BALLASTS
STRP32
3. SECURE BRACKETS WITH WIRE (BY OTHERS) TO ABOVE STRUCTURE.
FIG. 1-B
ITEM
1
2
3
4
5
HOOK
STRP31
2
2
1
1/2" APPROX.
3" APERTURE
3 15/32" HOUSING O.D.
3 5/8" ROUGH-IN*
5/8" DRYWALL
(BY OTHERS)
FIBERGLASS DRYWALL
TAPE WITH PLASTER
SKIMCOAT (BY OTHERS)
DRYWALL SCREWS 1" LENGTH MIN.
(BY OTHERS)
JOINT COMPOUND/MUD AND FEATHER
(BY OTHERS)
1
1
2
NOTE: FIXTURE TO
BE INSTALLED
BEFORE DRYWALL.
HOLD APERTURE DIM 3" WHEN INSTALLING DRYWALL
1. FOR ACCESS TO BALLAST(S), REMOVE LENS 5 (SEE STEP 6). USE FLATHEAD SCREWDRIVER TO PRY LENS OUT OF HOUSING.
2 REMOVE REFLECTORS BY PUSHING REFLECTORS UP SO THAT TABS ARE RELEASED FROM HOUSING NOTCHES, THEN PULL DOWN ON REFLECTOR.
NOTE: THERE ARE (3) TABS PER 3'-5' REFLECTOR & (4) TABS PER 6'-8' REFLECTOR. USE INDICATING HOLES TO LOCATE TABS.
3. REMOVE BALLAST CHANNEL COVER BY UNSCREWING (2) 8-32 X 3/8" SELF-TAPPING SCREWS 2 FOR ACCESS TO
BALLAST(S) (SEE FIG. 1-B RIGHT).
HOUSING
FLANGE
HOUSING
FLANGE
5
* INSTALL SHEETROCK WITH THIS TOLERANCE - AFTER
FIXTURE IS INSTALLED - TO AVOID BOWING FIXTURE SIDES.
AFTER INSTALLATION, UNIT IS TO BE AS SHOWN ABOVE, WITH ONLY THE BOTTOM OF THE FIXTURE VISIBLE.
RECOMMENDED SHEETROCK THICKNESS IS 5/8" WITH ROUGH-IN WIDTH OF 3 5/8".* DRYWALL SCREWS
(BY OTHERS) ARE TO ATTACH THE DRYWALL TO FIXTURE FLANGES. FIXTURE FLANGE STARTS 3 1/4"
FROM EITHER END OF FIXTURE FOR UNITS MOUNTED IN ROWS & 3/4" FROM EITHER END OF FIXTURE
FOR INDIVIDUALS, AS SHOWN IN STEP 1. PLASTER (BY OTHERS) TO COAT SHEETROCK.
2
FIG. 1-A
HOUSING
5
5
COVER
NOTE: END SHELL
NOT SHOWN HERE FOR
ILLUSTRATION PURPOSES.
DRYWALL
(BY OTHERS)
HOOK
REFLECTOR
NOTCH
REFLECTOR
2. RAISE OTHER EDGE OF LENS UP INTO FIXTURE UNTIL EDGE OF LENS CLEARS
HOUSING FLANGE & "SNAPS" ABOVE HOUSING FLANGE.
NOTE: HEIGHT THAT LENS "SNAPS" INTO PLACE IN FIXTURE VARIES
DEPENDING ON WHETHER HOUSING IS STRP31 OR STRP32 (SEE ABOVE).
LINEAR LIGHTING RESERVES THE RIGHT TO MAKE ANY
MECHANICAL CHANGES TO THE FIXTURE WHICH DO NOT
AFFECT THE OVERALL APPEARANCE OR PERFORMANCE.
NOTE: CEILING AND WALLS TO BE ADEQUATELY REINFORCED
TO SUPPORT FIXTURE WEIGHT. LINEAR LIGHTING IS NOT
RESPONSIBLE FOR IMPROPER REINFORCEMENT.
DESCRIPTION
WIRING ACCESS COVER
SCREW 8-32x3/8" SELF-TAPPING
SCREW 8-32x3/8" PAN HEAD MACHINE
NUT, 8-32 KEPS
SANDBLASTED LENS (SBL)
ARCHITECT:
ENGINEER:
LIGHTING DESIGNER:
CONTRACTOR:
DISTRIBUTOR:
PROJECT: <>
LINEAR LIGHTING
INDICATING
HOLE
TAB
PULL DOWN ON REFLECTOR
SO THAT REFLECTOR
NOTCHES ARE RELEASED
FROM HOOKS IN HOUSING.
284577
630001
630011
630017
450692
SHEET, STRIPE 31/32
TITLE: INSTALLATION
(STRP31/STRP32) RECESSED FLANGELESS FIXTURE
TYPE:
31-30 HUNTERS POINT AVE.
LONG ISLAND CITY, N. Y. 11101
TEL:(718)361-7552 FAX:(718)937-2747
HOUSING
NOTCH
1. RAISE EDGE OF LENS 5 OVER HOUSING FLANGE AS SHOWN.
LINEAR P/N
FOR FIXTURE DETAIL SEE SHEET(S):<>
FOR LAYOUT & SCHEDULE SEE SHEET(S):<>
3
REFLECTOR
FIXTURE FLANGES
4
ASSEMBLY DRAWING NO: D0117622
DATE
REV
DESCRIPTION
BY
REVISIONS
THIS PRINT IS THE PROPERTY OF LINEAR LIGHTING CORP.,
AND THE INFORMATION IT CONTAINS MAY NOT BE USED
WITHOUT THE WRITTEN CONSENT OF LINEAR LIGHTING.
DRAWN BY:
DATE:
PROJECT DRAWING NO:
SHEET
OF
REV.