Megator SLS single pump pressure set Megator SLT twin pump pressure set The pressure sets are supplied as single, twin or three-pump units. The usual arrangement is to have twin-pump sets for main and stand-by/support operation, the stand-by/support pump can either be selected by a manual switch on the control panel or can be made to start automatically should the duty pump fail or become unable to meet an abnormal demand. If required, threepump sets for fresh and salt water services incorporating a common stand-by pump can be supplied. The method of changeover from duty to stand-by, is by means of flexibles, making this operation exceptionally simple and foolproof against incorrect connection. Marine Pressure Sets Megator Marine Pressure Sets are compact self-contained units, incorporating Megator Sliding Shoe Pumps on anti-vibration mountings, hydraulic accumulator, interwired control panel and all interconnecting piping assembled on a fabricated steel frame. Onboard installation only requires piping connections to suction and discharge manifolds and connection of the main electrical supply to the control panel. Selection Single Pum p Units Type Pum p Pum p Motor Accum ulator Capacity size rating capacity HP Gallons GPM SLS10 4.4 H75 1 26 SLS20 8.8 H100 1.5 52 SLS30 13.2 H125 2 52 SLS50 22 H150 3 79 Purpose - Built Sets Megator specializes in the design and production of complete packaged units to customers based on individual requirements. Equipment From the standard ratings tables, select the pressure unit with pump sized to meet estimated peak demand. Auto support feature (twin pump unit) provides double capacity to meet any exceptional peak demands that may occur in service. Working pressures up to 85 psi and total suction lifts up to 23 ft. Twin Pump Units Capacity Pump Duty pump with size Type only Auto support GPM GPM SLT20 8.8 17.6 H75 SLT30 13.2 26.4 H100 SLT50 22 44 H125 SLT75 33 66 H150 SLT100 44 88 H200 Motor rating HP Accumulator capacity Gallons 1.5 2 3 4.0 5.5 52 52 79 132 132 Pumps Control Panel Megator self-priming, sliding-shoe type with cast iron body, stainless steel rotor, port plate and mechanical shaft seals. Fitted with sealed bearings requiring no lubrication. Single compartment type with hinged cover, enclosure IP54. Includes triple-pole contactor for each pump with thermal overload, under voltage and single-phase protection with hand reset, earth leakage circuit breaker, hand/off/auto switch for each pump, pump selector switch, HRC fuses for motor and control circuits, 110 Volt control circuit transformer and triple pole isolating switch interlocked with hinged cover incorporating white “power on” light. Pressure switches for duty and support pumps mounted on side of panel which are easily adjusted to give required cut-in and cut-out pressures up to 85 psi maximum. Motors To USCG requirements, class F insulation, class B temperature rise, TEFC, IP55. Suitable for 380440V/3ph/50-60Hz electrical supply. Pipework Copper with bronze valves including non-return valve on pump discharge, isolating valve and pump relief valve on discharge manifold, isolating valve on pump suction. Manifolds terminate in flanged flexible connections to minimize transmitted vibration. Pressure gauges with 21/2” dial calibrated 0-140 psi for system pressure and accumulator pre-charge pressure are mounted on framework of unit. Painting Unit painted based on customer specifications or standard one coat of primer and one coat of hammer green finish. Optional Extras Ultra violet purification unit. Hydraulic accumulator Water-in-bag type with replaceable flexible membrane in epoxy coated shell with bolted access cover, relief valve and connection for charging (supply pressure must not exceed 114 psi). Calorifier unit. Bronze pumps. Pump, motor, control panel and accumulator spares. Pump running lights. 1721 Main St, Pittsburgh, PA 15215 Tel: 412.963.9200 1.800.245.6211 Fax: 412.963.9214 www.megator.com Email: info@megator.com