CAT.EUS70-35A'-UK
Valve for Water and Chemical-based Fluids
(2/3 Port Air Operated Valve)
Applicable for 2 types of liquid paint (VCC12D)
PTFE diaphragm structure = Sliding part eliminated
Less paint adhesion
Mountable on a robot arm (space-saving, lightweight)
2 valves per station (30 mm pitch)
2/3 port valves mixed mounting
Resin manifold block
50
2700 g
12
Weight:
0
212
ATEX Explosion protection
SUS316L Stainless steel fitting
Series VCK
Series VCC
/ ø6 to ø12
2
port ··· 6 valves
 3 port ··· 6 valves
 Fitting ···19 pcs.
2 port valve
3 port valve
VCC12(D)
VCC13
Paint Line System
(Application example)
Water/Chemical-based Paint, Pure Water, Cleaning Solvent type
Paint circulation
(for 3 port valves)
Paint gun
Built-in 2 port valve
Painting
RETURN
IN
OUT
Regulator
Paint supply
(Direct supply possible)
(Max. 40 colours)
Selects paint colour.
2/3 port valve
Completely separates the
paint valve and the cleaning
valve, so the paint does not
enter the cleaning side.
Gate valve (2 port)
(Built in the manifold)
IN
Cleaning fluids
• Thinner
• Pure water
• Water solvent
• Air
Cleaning valve (2 port)
VCC manifold
2 port valve (VCC12)
IN
Leakage
detection port
3 port valve (VCC13)
Pilot
signal
Open
OUT
Leakage
detection port
IN
Switch
indicator
light
(Blue)
Pilot
signal
Switch
indicator
light
(Blue)
Open
OUT
Closed
Closed
Leakage detection port
IN RETURN
Paint leakage to the pilot piping can be checked visually. Even when
leakage occurs, there is no backflow between the paint and pneumatics.
2 types of Liquid Paint/PTFE Diaphragm
Single Paint, Solvent, Ink Control type/Single Unit
PAT.
Diaphragm
OUT
IN
Leakage
detection port
Pilot
signal
2 port valve (VCC12(D))
Switch
indicator
light
(Red)
3 port valve (VCC13)
PA
PA
IN
IN
Open
Closed
OUT
OUT
RETURN
Features 1
Manifold Valve
Separable Resin Manifold Block
Easy addition and reduction of stations
Tough PPS (Polyphenylene Sulfide) resin is used.
Fluororesin is contained. (Less fluid adhesion)
Antistatic (Surface resistance 102 to 105Ω) IN port
SUS316L Stainless steel fittings are standardized.
Stainless Steel 40° swivel elbow
centralises piping.
Leakage
detection
port
Gate/Cleaning valve
IN PA IN PA
2/3 port valve
RETURN RETURN RETURN
IN PA IN PA IN PA
IN PA
IN PA
Cleaning valve
Gate valve
OUT
2 port valve
OUT port
IN PA
PA
Gate valve
IN PA
IN PA
IN PA IN PA IN PA
RETURN RETURN RETURN
2 port valve manifold block assembly
3 port valve
IN port
RETURN port
PA (pilot) port
3 port valve manifold block assembly
Clip
Antistatic one-touch fitting
Easy attachment/removal with a clip.
No seal tape necessary. (Conductive)
Reduction of the
paint deposit
Surface sealed with resin
+ O-ring (Supplemental seal)
Cartridge type valve
The valve can be replaced
without touching the piping.
Less build-up of liquid → Better cleaning
performance, mixing of the colours reduction
Liquid build-up at valve is 0.01 cc or less.
Ensures stable sealing performance in case of
misalignment.
Spherical surface + Tapered shape
Special fluororesin seal
Even if the sphere is worn out,
The O-ring back-up ensures
sealing performance.
PAT.
Indicator function
Standard
(Sliding type)
Diaphragm
type
Operating condition can be
checked visually or by
touching.
Indicator color
Blue ··· VCC12, 13
Red ··· VCC12D
Features 2
SUS316L Stainless Steel Fitting
Single Unit
2
port valve
IN
VCKH
VCKK
VCKL
Male connector
40° swivel elbow
90° swivel elbow
PA (pilot) port
OUT
OUT
PA
IN
Leakage detection port
3
port valve
IN
40° swivel elbow is added in line-up.
Seal tape is unnecessary. No chance for insulation.
(Applicable for paint with high voltage)
 Attachment/removal in a narrow space is easy.

PA (pilot) port

IN
OUT
PA
OUT RETURN
RETURN port
Leakage detection port
Type
Model
Male connector
VCKH
40° swivel elbow
VCKK
90° swivel elbow
VCKL
Port size
Applicable
tubing O.D. x I.D.
G1/4
6x4
8x6
10 x 8
10 x 7.5
12 x 9
Special Tools
Disassembly and maintenance are possible.
Product design takes maintenance performance into consideration.
Attaching/Detaching the
valve
Disassembling/Cleaning
the valve element
Attaching/Detaching the tubing
Special tool
Special tool
Special tool
Special tool
(for socket wrench)
Made to Order
Check valve
Regulator
Note) Also applicable to special manifold.
Features 3
Valve for Water and Chemical Base Fluids
(2/3 Port Air Operated Valve)
Series VCC
I
N
D
E
X
 How to Order
Page 1
 Specifications/Weight
Page 3
 Dimensions
Single valve unit
Page 5
Manifold
Page 6
SUS316L Stainless steel fitting
Page 7
 Special Tools
 Disassembly/Assembly/
Maintenance Procedure
Page 9
Page 11
 Replacement Parts
Page 13
 Safety Instructions
Back page 1
 Specific Product Precautions
Back page 2
Front Matter 1
Valve for Water and Chemical-base Fluids
(2/3 Port Air Operated Valve)
Series VCC
II 2GD c 75°C (T6X)
Please refer to “Manifold Specification
Sheet” in the back of page 6.
How to Order
Valve
VCC1 2
00
Passage number
2 port valve
2
3 port valve
3
2D 2 port/Diaphragm type (Applicable for 2 liquid paint)
Port size
00 For manifold mounting
02 Rc1/4 (for single unit) Note)
02F G1/4 (for single unit) Note)
VCC12(D)-00
VCC13-00
VCC12(D)-02(F)
VCC13-02(F)
Note) Part number for sub-base
[Rc1/4]
For 2 port: VCC12-S- 02
02F [G1/4]
[Rc1/4]
For 3 port: VCC13-S- 02
02F [G1/4]
Manifold
Standard
VV M CC1 06 06 C4
Pilot port fitting size
Type (Passage number)
2
3
M
C4
C6
2 port valve, Cleaning valve
3 port valve
2/3 port valves mixed mounting
2 port valve mountable number
00
02
04
No 2 port valves used
2 pcs. (colours)
4 pcs. (colours)
ø4 one-touch fitting (Antistatic)
ø6 one-touch fitting (Antistatic)
3 port valve mountable number
00
02
04
No 3 port valves used
2 pcs. (colours)
4 pcs. (colours)
Note) Maximum mountable valve number: 40 pcs.
(total of 2 port and 3 port valves)
Circuit example
2 port valve
IN PA
IN PA
IN PA
3 port valve
2 port valve
1 pc.
3 pcs.
5 pcs.
RETURN RETURN RETURN
IN PA
IN PA
IN PA
OUT
2 pcs.
4 pcs.
IN PA
IN PA
IN PA
IN PA
IN PA
IN PA
RETURN RETURN RETURN
Note) ATEX Explosion Protection for 2/3 port air operated valves and
manifolds is also applicable to made-to-order versions except
for models made of aluminium.
1
6 pcs.
2 pcs.
4 pcs.
6 pcs.
3 port valve
1 pc.
3 pcs.
5 pcs.
Valve for Water and Chemical-base Fluids
Series VCC
How to Order
Manifold
With gate valve
VV M CC1 06 06 C4 G 04
Passage number
Gate valve and cleaning valve mountable number
2 2 port valve, Cleaning valve
M 2/3 port valves mixed mounting
02
04
06
2 port valve
mountable number
00
02
04
Pilot port fitting size
3 port valve
mountable number
No 2 port valves used
2 pcs. (colours)
4 pcs. (colours)
00
02
04
C4 ø4 one-touch fitting (Antistatic)
C6 ø6 one-touch fitting (Antistatic)
No 3 port valves used
2 pcs. (colours)
4 pcs. (colours)
∗ The gate valve and cleaning valve (2 port valve) are not
included. They are ordered separately. (Gate valve is
equivalent to 2 port valve.)
∗ When cleaning valve number is an even number, use the
blanking plug for 2 port valve.
Note) Maximum mountable valve
number: 40 pcs. (total of 2
port, 3 port and gate valves)
Circuit example
2/3 port valve
Gate/Cleaning valve
IN PA
IN PA
Cleaning valve (2 port valve): 1 pc. + Gate valve: 1 pc.
Cleaning valve (2 port valve): 3 pcs. + Gate valve: 1 pc.
Cleaning valve (2 port valve): 5 pcs. + Gate valve: 1 pc.
IN PA
Cleaning valve
RETURN RETURN RETURN
IN PA
IN PA
IN PA
Cleaning valve
OUT
Cleaning valve
OUT
Gate valve
PA
IN PA
IN PA
Gate valve
IN PA
IN PA
IN PA
RETURN RETURN RETURN
SUS316L Stainless steel fitting
Note) ATEX Explosion Protection for 2/3 port air operated valves and
manifolds is also applicable to made-to-order versions except
for models made of aluminium.
VCK K 0604 02F
Port size
Shape
H
K
L
02F
Male connector
40° swivel elbow
90° swivel elbow
G1/4
∗ G1/4 bottom seal has a special
shape. Please refer to page 7
for details.
Applicable tubing
(O.D. x I.D.)
0604 6 x 4
0806 8 x 6
1075 10 x 7.5
1008 10 x 8
1209 12 x 9
VCKH
Male connector
VCKK
40° swivel elbow
VCKL
90° swivel elbow
Option
Blanking Plug Assembly
Type
Model
For a 2 port valve
VVCC12-10A-1
For a 3 port valve
VVCC13-10A-1
Description
Blanking plug (with O-ring)
Qty.
1
Hexagon socket head plug (R1/4)
1
Blanking plug (with O-ring)
1
Hexagon socket head plug (R1/4)
2
2
Series VCC
Specifications
Model
Passage number
Construction
(Fluid contact material)
VCC12
VCC13
2 port
3 port
VCC12D
2 port (Diaphragm type)
Poppet seal (PEEK resin + Stainless steel)
+ Special fluororesin sliding part
Fluid
Poppet seal (PEEK resin + Stainless steel)
+ Special fluororesin diaphragm
Water/Chemical-based paint, Ink, Cleaning solvent (Water, Butyl acetate), Air
Operating pressure range (MPa)
0 to 1.0 (Instantaneous pulsation pressure: 1.2)
0 to 0.7 (Instantaneous pulsation pressure: 0.9)
Withstand pressure
(MPa)
Pilot pressure
(MPa)
0.4 to 0.7
Orifice size
(mm)
ø3.8
Effective area
(mm2)
6
Fluid temperature
(°C)
ATEX explosion protection specification: 5 to 50 (T6X)
Ambient temperature
(°C)
ATEX explosion protection specification: 5 to 50 (T6X)
2
Explosion proof construction
1.5
Explosion protection
Lubrication
Mounting orientation
Valve leakage
II 2GD c 75°C (T6X)
Not possible (Default lubricant: White vaseline)
Unrestricted
(cm3/min)
1 or less (3 port valve IN → RETURN: 20 or less) Note 1)
1 or less Note 2)
Note 1) Supply pressure: Valve leakage at 1.2 MPa (for air)
Note 2) Supply pressure: Valve leakage at 0.9 MPa (for air)
SUS316L Stainless Steel Fitting Specifications
Applicable tubing
Nylon/Fluoro tubing
Fluid
Water/Chemical-based paint, Ink, Cleaning solvent (Water, Butyl acetate), Air
Max. operating pressure (at 20°C) (MPa)
Ambient and fluid temperature
1.0
(°C)
0 to 60°C
Weight
Valve
Blanking plug assembly
Manifold block
∗ Valves are not attached.
End plate
VCC12 (2 port)
37 g
VCC13 (3 port)
48 g
For 2 port
29 g
For 3 port
150 g
For 3 port (2 stations, one-piece style)
254 g
For gate valve
300 g
For 2 port
409 g
For 3 port
495 g
For 2/3 port mixed mounting
452 g
ø6
24 g
ø8
25 g
ø10
33 g
ø12
36 g
ø6
25 g
ø8
26 g
ø10
32 g
ø12
37 g
ø6
29 g
ø8
30 g
ø10
37 g
ø12
41 g
VCKH
Fitting
VCKK
VCKL
3
45 g
For 2 port (2 stations, one-piece style)
Valve for Water and Chemical-base Fluids
Series VCC
Dimensions
Mounting hole dimensions (When the valve is built into the device.)
VCC12(D)-00
38.8±0.1
23±0.1
1.2 to 2 hole
IN port
16.5±0.1
4 hole
R0
OUT port
.2
C
1
ø21.6±0.05
ø21±0.05
ø20±0.05
30°
.2
R0
ø24±0.05
Pilot port
1.2 hole
M26
3.8 hole
Leakage detection port
30°
30°
2.5
8.5
33±0.1
40.8
±0.1
45±0.1
∗ The recommended insertion surface roughness is Rz6.3.
VCC13-00
45.9±0.1
38.4±0.1
23±0.1
1.2 to 2 hole
4 hole
16.5±0.1
4 hole
RETURN port
Leakage detection port
1.2 hole
Pilot port
IN port
R0.2
30°
C
1
M26
3.8 hole
ø23±0.05
ø22.5±0.05
ø22±0.05
ø24±0.05
OUT port
30°
30°
30°
2.5
32.7
8.5
±0.05
40.5±0.1
48±0.1
55±0.05
∗ The recommended insertion surface roughness is Rz6.3.
4
Series VCC
Dimensions
Single valve unit
VCC12(D)-02(F)
M5 leakage detection port
22
30
23
60
0.5 to 2
2 x ø6 (for M5 mounting)
6
48
G1/4, Rc1/4 OUT(2) port
22
25
43
25
6
22
15
15
38.7
16.5
Rc1/8 pilot (12) port
15
G1/4, Rc1/4 IN(1) port
∗ Part number for sub-base
[Rc1/4]
VCC12-S- 02
02F [G1/4]
G1/4, Rc1/4 RETURN(3) port
11
19
M5 leakage detection port
30
VCC13-02(F)
23
38.4
70
0.5 to 2
2 x ø6 (for M5 mounting)
6
22
G1/4, Rc1/4 OUT(2) port
22
25
50
25
6
58
15
15
45.9
16.5
Rc1/8 pilot (12) port
15
G1/4, Rc1/4 IN(1) port
∗ Part number for sub-base
[Rc1/4]
VCC13-S- 02
02F [G1/4]
5
Valve for Water and Chemical-based Fluids
Series VCC
Dimensions
8
50
64.9
Manifold
10.5
Leakage detection port
Pilot port
C4: ø4 one-touch fitting
C6: ø6 one-touch fitting
G1/4 (IN port)
0.5 to 2
5
2
4
6
7
9
n-1
8
10
n
L1
8
L2
4 x ø9
(for M8
mounting)
2 port valve
120
3
142.2 <144.2>
10
1
0.5 to 2
67.5 <69.5>
G1/4 (RETURN port)
25
0.5 to 2
50
50
64.9
67.5 <69.5>
30
22.6
120
142.2 <144.2>
100
122.2 <124.2>
122.2 <124.2>
20
G1/4
OUT port
80
0.5 to 2
20
G1/4
OUT port
31
10
75
VV2CC1
100
VVMCC1, VV3CC1
3 port valve
Pilot port
C4: ø4 one-touch fitting
C6: ø6 one-touch fitting
G1/4 (IN port)
1
1
3
Gate valve
2
3
5
n-1
4
6
n
0.5 to 2
25
L1
8
L2
4 x ø9
(for M8
mounting)
Cleaning valve +
Gate valve
142.2 <144.2>
0.5 to 2
2
75
10
22.6
80
100
0.5 to 2
10
0.5 to 2
122.2 <124.2>
G1/4 (RETURN port)
30
120
31
3 port valve
2 port valve
< >: Pilot port is C6.
L1 = n / 2 x 30 + 16 L2 = n / 2 x 30 + 32
∗ n = Number of valves (cleaning valve + gate valve + other valves)
n: Stations (mm)
n
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
L1
L2
46
76
106
136
166
196
226
256
286
316
346
376
406
436
466
496
526
556
586
616
62
92
122
152
182
212
242
272
302
332
362
392
422
452
482
512
542
572
602
632
6
Series VCC
Dimensions
SUS316L Stainless steel fitting
Mounting female thread recommended dimensions
es
s
9 to 11
7 or more
G1/4
C
0.
5
or
l
ø4 or less
Bottom seal
Seal material: Nylon
VCKH Male connector
Width across flats E
ø13
A
0.5
4.5
13.5
6
≈C
D
≈G
∗ After tightening
manually, tighten 1.5
to 2 more turns.
Width across flats F
ø10
∗ Tightening torque: Tighten within 10 ± 1 N  m.
G1/4
(mm)
Part no.
Indication of A
øB
C
D
E
F
G
VCKH1209-02F
VCKH1008-02F
VCKH1075-02F
VCKH0806-02F
VCKH0604-02F
12/9
13
38.5
10
19
17
18.5
10/8
11
38
9
17
17
18.5
10·75
11
38
9
17
17
18.5
8/4
9
36.5
8
14
14
16
6/4
7
36.5
8
12
14
15
VCKK 40° swivel elbow
40°
øB
10
≈
F
D
A
Width across flats 14
≈C
∗ Tightening torque:
Tighten within 10 ± 1 N  m.
∗ After tightening
manually, tighten 1.5
to 2 more turns.
0.5
2.8
5.8
11.8
13.8
18.8
Width across flats E
ø8.6
ø11
G1/4
(mm)
7
Part no.
Indication of A
øB
C
D
E
F
VCKK1209-02F
VCKK1008-02F
VCKK1075-02F
VCKK0806-02F
VCKK0604-02F
12/9
13
49.5
10
19
18.5
10/8
11
48.5
9
17
18.5
10·75
11
48.5
9
17
18.5
8/4
9
46
8
14
16
6/4
7
45.5
8
12
15
Series VCC
Valve for Water and Chemical Base Fluids
Dimensions
VCKL 90° swivel elbow
≈E
A
Width across flats G
F
≈H
10
0.5
2.8
11.8
5.8
13.8
D
18.8
Max. = C
øB
∗ After tightening
manually, tighten 1.5
to 2 more turns.
ø8.6
Width across flats 14
∗ Tightening torque:
Tighten within 10 ± 1 N  m.
ø11
G1/4
(mm)
Part no.
Indication of A
øB
C
D
E
F
G
H
VCKL1209-02F
VCKL1008-02F
VCKL1075-02F
VCKL0806-02F
VCKL0604-02F
12/9
13
43.5
33
30.5
10
19
18.5
10/8
11
42.5
33
30
9
17
18.5
10·75
11
42.5
33
30
9
17
18.5
8/4
9
40
32
27.5
8
14
16
6/4
7
38.5
32
27.5
8
12
16
8
Special Tools
Tool for Attaching/Detaching the Valve
VCC-G-A
Knurled
ø8
4 x ø1.8
ø25
1
ø2
For attaching/
detaching the
valve
104
M16
VCC-G-A
VCC-G-B
VCC-G-B (for socket wrench)
Knurled
4 x ø1.8
ø28
1
ø2
Socket wrench
A-type 6.3 square drive
24
Tool for Disassembling/Cleaning the Valve Element
VCC12(D) 2 port valve
VCC-G-C
For 3 port valve
Knurled
ø8
ø19
ø1
2.7
3.
ø1
4 x ø1.8
4
For 2 port valve
105
VCC13 3 port valve
9
4 x ø1.3
Valve for Water and Chemical-based Fluids
Series VCC
Union Nut Socket
1209
VCC-G-D- 12
VCC-G-D-1 (Applicable fitting VCK1008
)
1075
13
Width across flats: 19
.5
25
14
60
VCC-G-D-2 (Applicable fitting VCK 0806
0604 )
9
Width across flats: 17
5
20.
14
50
For extending the socket
VCC-G-D-1
VCC-G-D-1
113
VCC-G-D-1
VCC-G-D-2
97
10
Disassembly/Assembly/
Maintenance Procedure
Cleaning Valve Element
Special tool part no.: VCC-G-C
VCC13-00 (3 port valve)
VCC12-00 (2 port valve)
Body
Body
VCC13-1A-1
VCC12-1A-1
Valve element
Orifice body assembly
Valve element
Orifice assembly
3 lines
2 lines
Screw
Screw
Jig: VCC-G-C
Procedure
q Loosen the orifice body with a tool and remove it.
w Clean the valve.
e Assemble a new orifice body.
VCC12(D)-00 (2 port valve)
0.2
Full length: 44.8 to 45.1
Except face seal (O-ring)
VCC13-00 (3 port valve)
0.4
Full length: 54.6 to 54.9
Except face seal (O-ring)
Tighten the screw until it hits the body by pressing the orifice body with approx. 100 to 200 N of force.
(∗ Additional tightening is not necessary.)
Control dimension with full length. (2 port valve: 44.8 to 45.1 mm, 3 port valve: 54.6 to 54.9 mm)
Reference tightening torque is approx. 1 to 2 Nm for VCC12(D)-00 (2 port valve), and 0.5 to 1 Nm for VCC13-00 (3 port valve).
There is a possibility of damaging threads if tightening exceeds the tightening torque range.
11
Valve for Water and Chemical-based Fluids
Series VCC
How to Remove the Valve
Special tool part no.: VCC-G-A, VCC-G-B (Refer to page 9.)
r
q
e
Thread for detaching the body
(M16)
Procedure
t Wipe off residual paint on the inner surface of the base with a cleaning
material.
y Replace the O-ring mounted to the valve.
(O-ring part number: See page 13.)
q Loosen the mounting nut.
w Remove the indicator lamp cover.
e Turn 45 to 90° (idle turn) clockwise with a tool (to avoid O-ring
adhesion).
r Pull out the valve straight.
How to Attach the Valve
Apply vaseline.
Apply vaseline (commercially available) onto the O-ring surface and
insert straight. (Note the direction shown in the label.)
O-ring for paint
Special FKM
G1/4
After mounting the indicator lamp cover, tighten the mounting nut to a
tightening torque of 2.5 to 3.5 Nm
G1/4
IN
IN
Place the arrow within
±15° of IN port position.
O-ring for air
HNBR
G1/4
RETURN
Production lot number
JAPAN
ON
OFF
C12- 00
VC
IS
OUT
OUT
SMC
IN port in valve
2 port valve
IN port in valve
Part no.
3 port valve
Model label
Attach and remove the valve straight. If the paint applied to the O-ring adheres to the pneumatic passage, clean it.
When inserting, apply vaseline to the O-ring and the inner surface of the base and insert slowly so that the O-ring is not twisted or cut.
The arrow shown on the model label of the valve is set to the optimum direction for cleaning. Mount the valve so that the arrow comes to IN port
position.
12
Replacement Parts
VVCC1: Manifold
∗ Tighten on a flat surface (e.g. holding plate) so that the end plates on both ends are not twisted.
M5 Hexagon socket head cap screw
Tightening torque: 3.5 ± 0.5 N  m
J
D side
K
G1/4 port part
Tightening torque: 10 ± 1 N  m
G
ewq
H
ewq
rqwe
F
q
E
w
C
A
U side
B
D
M5 Hexagon socket head cap screw
Tightening torque: 3.5 ± 0.5 N m
Block Assembly
C: 2 port valve manifold block assembly
D: 3 port valve manifold block assembly
Manifold block assembly for gate valves
M4 Round head combination screw
Tightening torque: 1.2 ± 0.2 N  m
y
w
e
r
t r q e w
o i q u t
Component Parts
Model
VV2CC1
VV3CC1
VVMCC1
(common)
VV3CC1
VVMCC1
13
Part no.
VVCC12-OR-1
VVCC12-50A-L1C4
VVCC12-50A-L1C6
VVCC13-OR-1
Description
O-ring between manifold
blocks
Symbol
C-w
D-t
C-t
ø4 one-touch fitting
D-o
ø6 one-touch fitting
O-ring assembly between D-e
port blocks
D-r
Component
Material
Qty.
Order qty.
O-ring
Special FKM
1
10 set unit
One-touch fitting
—
1
O-ring
HNBR
1
O-ring
Special FKM
2
O-ring
Special FKM
2
1 set unit
1 set unit
Valve for Water and Chemical-based Fluids
Series VCC
2/3 Port Valve
A: 2 port valve
Standard
Diaphragm / 2 types of liquid paint
VCC12-00
VCC12D-00
ywert
i
o
!2
!0 !1
y
i
!3
u
q
u
B: 3 port valve
VCC13-00
et
r
y
q
w
Component Parts
Model
Part no.
Description
Orifice body assembly
VCC12-1A-1
(for VCC12-00)
VCC12(D)-00
(dedicated)
Orifice body assembly
VCC12D-1A-1
(for VCC12D-00)
VCC12-OR-1
O-ring assembly
Orifice assembly
VCC13-1A-1
VCC13-00
(dedicated)
VCC13-OR-1
VCC12(D)-00
VCC13-00
(common)
O-ring assembly
Mounting nut assembly
Symbol
A-q
Component
Orifice body
Material
PEEK resin
Qty.
1
A-w
A-e
A-r
A-t
A-y
A-u
A-!1
A-y
A-u
A-!2
A-!3
A-y
A-u
A-i
B-q
B-w
B-e
B-r
B-w
B-t
B-y
PTFE seal
Special PTFE
1
O-ring
Special FKM
1
Sleeve
POM
1
O-ring
Special FKM
1
O-ring
Special FKM
2
O-ring
Special FKM
1
Name plate
—
1
O-ring
Special FKM
2
O-ring
Special FKM
1
Orifice body
PEEK resin
1
Name plate
—
1
O-ring
Special FKM
2
O-ring
Special FKM
1
O-ring
HNBR
2
Orifice
PEEK resin
1
O-ring
Special FKM
1
O-ring
Special FKM
1
Name plate
—
1
O-ring
Special FKM
1
O-ring
Special FKM
3
O-ring
HNBR
2
A-o
Mounting nut
Aluminum
1
A-!0
Switching display
cover
A-PET
1
VCC12-2A-1
Order qty.
1 set unit
1 set unit
1 set unit
1 set unit
1 set unit
1 set unit
14
Series VCC
Parts Description
Model Symbol
A
Part no.
VCC12(D)-00
Description
2 port valve
C4
VVCC12-1A-02F C6
∗ Pilot port
C4: ø4 piping
C6: ø6 piping
C
C4
VVCC12-1G-02F C6
For 2 port valve
∗ Pilot port
C4: ø4 piping
C6: ø6 piping
E
F
G
B
VVCC12-10A-1
VCC13-00
For 3 port valve
E
F
Common
H
∗ Pilot port
C4: ø4 piping
C6: ø6 piping
VVCC13-2A-02F
VVCC13-3A-1
VVCC13-10A-1
Material
—
Surface treatment
—
PPS resin
—
q
Manifold block
w
—
r
Special FKM
O-ring
Tie-rod for adding stations Stainless steel
Stainless steel
Clip
t
One-touch fitting
—
—
q
U-side end plate
Aluminium
w
Hexagon socket head cap
screw with M5 SW
q
D-side end plate
w
Plug
e
O-ring
r
Hexagon socket head cap
screw with M5 SW
Blanking plug
assembly for 2 port
valve
q
Blanking plug
w
O-ring
e
3 port valve
Manifold block
assembly for gate
valves
D-side end plate
assembly for 2 port
valves
VVCC12-3A-1
C4
VVCC13-1A-02F C6
D
Manifold block
assembly for 2 port
valves
U-side end plate
assembly for 2 port
valves
VVCC12-2A-02F
Description
—
Symbol
—
Manifold block
assembly for 3 port
valves
U-side end plate
assembly for 3 port
valves
D-side end plate
assembly for 3 port
valves
Blanking plug
assembly for 3 port
valves
e
Aluminium
Stainless steel
C4
For VVCC12-1A-02F C6
Hard anodized
C4
For VVCC12-1G-02F C6
containing PTFE
—
—
For adding stations
—
Refer to “Replacement Parts.”
Hard anodized
containing PTFE When the neighboring valve
is a 2 port valve.
—
Aluminium
Hard anodized
containing PTFE
POM
—
Special FKM
—
Stainless steel
Note
—
When the neighboring valve
is a 2 port valve.
—
POM
—
—
Special FKM
—
—
—
—
—
R1/4 Hexagon socket head plug Stainless steel
—
—
—
—
q
Manifold block
PPS resin
—
—
Aluminium
Hard anodized
containing PTFE
—
w
Port block
e
O-ring
Special FKM
—
—
r
O-ring
Special FKM
—
—
t
O-ring
Special FKM
—
—
y
Round head combination
Stainless steel
screw with M4 SW
—
—
u
Tie-rod for adding stations Stainless steel
—
i
Clip
—
o
One-touch fitting
Stainless steel
—
—
q
U-side end plate
w
Hexagon socket head cap
screw with M5 SW
q
D-side end plate
w
Plug
e
O-ring
r
Hexagon socket head cap
screw with M5 SW
q
Blanking plug
w
O-ring
e
R1/4 Hexagon socket head plug Stainless steel
Aluminium
Stainless steel
For adding stations
Refer to “Replacement Parts.”
Hard anodized
containing PTFE When the neighboring valve
is a 3 port valve.
—
Aluminium
Hard anodized
containing PTFE
POM
—
Special FKM
—
Stainless steel
—
POM
—
—
Special FKM
—
—
When the neighboring valve
is a 3 port valve.
—
—
J
VVCC12-20A-
Tie-rod
—
—
Stainless steel
—
 = Three manifold blocks
make up one set.
K
VVCC12-21A
Tie-rod for adding stations
—
—
Stainless steel
—
Note) 3 pcs. make up one set.
Note) When the manifold is shipped out, tie-rods for two extra stations are used. You can add or reduce 2 stations of manifold block (4 valves in total).
Example) For manifold block 4 stations (8 valves)
Tie-rod for 2 stations
(VVCC12-20A-2)
Tie-rod for adding
stations
(VVCC12-21A)
Tie-rod for adding
stations
(VVCC12-21A)
Example) For manifold block 5 stations (10 valves)
Tie-rod for 3 stations
(VVCC12-20A-3)
15
Tie-rod for adding
stations
(VVCC12-21A)
Tie-rod for adding
stations
(VVCC12-21A)
Valve for Water and Chemical-based Fluids
Series VCC
SUS316L Stainless Steel Fitting
L
M
N
Component Parts
Model
Symbol
Part no.
Description
KFN-06-X2
K
VCKL0604-02F
H
KFN-08-X2
K
VCKL0806-02F
H
L
Union nut
KFN-10-X2
K
VCKL-02F
H
K
VCKL1075-02F
H
K
VCKL1209-02F
H
KFS-06
K
VCKL0604-02F
H
KFS-08
K
VCKL0806-02F
H
Sleeve
KFS-10
Qty.
Order qty.
C3604BD + Ni plated
1
1 set unit
K
VCKL1075-02F
H
Nylon
1
1 set unit
Nylon
1
10 set unit
K
VCKL1008-02F
H
K
VCKL1209-02F
H
KFS-12
VCKK-4-1
Material
K
VCKL1008-02F
H
KFN-12-X2
M
N
Conforming item
Gasket
16
Series VCC
Safety Instructions
These safety instructions are intended to prevent a hazardous situation and/or equipment damage. These
instructions indicate the level of potential hazard by labels of "Caution", "Warning" or "Danger". To
ensure safety, be sure to observe ISO 4414 Note 1), JIS B 8370 Note 2) and other safety practices.
Explanation of the Labels
Labels
Danger
Warning
Caution
Note 1)
Note 2)
Note 3)
Note 4)
Explanation of the labels
In extreme conditions, there is a possible result of serious injury or loss of life.
Operator error could result in serious injury or loss of life.
Operator error could result in injury Note 3) or equipment damage. Note 4)
ISO 4414: Pneumatic fluid power – General rules relating to systems
JIS B 8370: General Rules for Pneumatic Equipment
Injury indicates light wounds, burns and electrical shocks that do not require hospitalization or hospital visits for long-term medical treatment.
Equipment damage refers to extensive damage to the equipment and surrounding devices.
Selection/Handling/Applications
1. The compatibility of the pneumatic equipment is the responsibility of the person who designs the
pneumatic system or decides its specifications.
Since the products specified here are used in various operating conditions, their compatibility for the specific pneumatic system
must be based on specifications or post analysis and/or tests to meet the specific requirements. The expected performance and
safety assurance are the responsibility of the person who has determined the compatibility of the system. This person should
continuously review the suitability of all items specified, referring to the latest catalogue information with a view to giving due
consideration to any possibility of equipment failure when configuring a system.
2. Only trained personnel should operate pneumatically operated machinery and equipment.
Compressed air can be dangerous if handled incorrectly. Assembly, handling or repair of pneumatic systems should be
performed by trained and experienced operators. (Understanding JIS B 8370 General Rules for Pneumatic Equipment, and other
safety rules are included.)
3. Do not service machinery/equipment or attempt to remove components until safety is confirmed.
1. Inspection and maintenance of machinery/equipment should only be performed once measures to prevent falling or runaway
of the driven objects have been confirmed.
2. When equipment is removed, confirm that safety process as mentioned above. Turn off the supply pressure for this equipment
and exhaust all residual compressed air in the system, and release all the energy (liquid pressure, spring, condenser, gravity).
3. Before machinery/equipment is restarted, take measures to prevent quick extension of a cylinder piston rod, etc.
4. If the equipment will be used in the following conditions or environment, please contact SMC first and
be sure to take all necessary safety precautions.
1. Conditions and environments beyond the given specifications, or if product is used outdoors.
2. Installation on equipment in conjunction with atomic energy, railway, air navigation, vehicles, medical equipment, food and
beverages, recreation equipment, emergency stop circuits, clutch and brake circuits in press applications, or safety equipment.
3. An application which has the possibility of having negative effects on people, property, requiring special safety analysis.
4. If the products are used in an interlock circuit, prepare a double interlock style circuit with a mechanical protection function for
the prevention of a breakdown. Examine the devices periodically if they function normally or not.
Exemption from Liability
1. SMC, its officers and employees shall be exempted from liability for any loss or damage arising out of
earthquakes or fire, action by a third person, accidents, customer error with or without intention, product misuse, and any other damages caused by abnormal operating conditions.
2. SMC, its officers and employees shall be exempted from liability for any direct or indirect loss or damage, including consequential loss or damage, loss of profits, or loss of chance, claims, demands, proceedings, costs, expenses, awards, judgments and any other liability whatsoever including legal costs
and expenses, which may be suffered or incurred, whether in tort (including negligence), contract,
breach of statutory duty, equity or otherwise.
3. SMC is exempted from liability for any damages caused by operations not contained in the catalogues
and/or instruction manuals, and operations outside of the specification range.
4. SMC is exempted from liability for any loss or damage whatsoever caused by malfunctions of its products when combined with other devices or software.
Back page 1
Series VCC
Specific Product Precautions 1
Be sure to read this before handling. For Safety Precautions, refer to back page 1.
For Precautions, refer to “Precautions for Handling Pneumatic Devices” (M-03-E3A).
Design
Piping
Caution
Warning
1. Cannot be used as an emergency shutoff
valve, etc.
The valves presented in this catalogue are not designed for
safety applications such as an emergency shutoff valve. If the
valves are used in this type of system, other reliable safety
assurance measures should also be adopted.
2. Maintenance space
The installation should allow sufficient space for maintenance
activities.
3. When an impact, such as water hammer,
etc., caused by the rapid pressure fluctuation is applied, the solenoid valve may be
damaged. Handle with care.
1. Preparation before piping
Before piping is connected, it should be thoroughly blown out
with air (flushing) or washed to remove chips, cutting oil and
other debris from inside the pipe.
Install piping so that it does not apply pulling, pressing, bending or other forces onto the valve body.
2. Wrapping of pipe tape
When connecting pipes, fittings, etc., be sure that chips from
the pipe threads and sealing material do not enter the valve.
Furthermore, when pipe tape is used, leave 1.5 to 2 thread
ridges exposed at the end of the threads.
Winding
direction
Ex
po
Selection
se
Warning
1. Confirm the specifications.
Give careful consideration to the operating conditions such as
the application, fluid and environment, and use within the operating ranges specified in this catalogue.
2. Fluid
1) Applicable fluids on the list may not be used depending on the operating condition.
Give adequate confirmation, and then determine a model,
just because the compatibility list shows the general case.
3. Air quality
1) Use clean air.
Do not use compressed air containing chemicals, synthetic
oils,organic solvents, salt or corrosive gases, etc., as it can
cause damage or malfunction.
2) Install air filters.
Install air filters close to the valves at their upstream side. A
filtration degree of 5 µm or less should be selected.
3) Install an air dryer or after-cooler, etc.
Compressed air that includes excessive drainage may cause malfunction of the valves and other pneumatic equipment. To prevent this, install an air dryer or after-cooler.
4) If excessive carbon powder is generated, eliminate it by
installing mist separators at the upstream side of the
valves.
If excessive carbon powder is generated by the compressor, it may adhere to the inside of the valves and cause
malfunction.
Refer to SMC’s “Best Pneumatics” catalogue for further details
on compressed air quality.
4. Ambient environment
Use within the operable ambient temperature range. Confirm
the compatibility between the product’s composition materials
and the ambient atmosphere. Be sure that the used fluid does
not touch the external surface of the product.
5. Countermeasures against static electricity
Pipe tape
ap
pr
ox
.2
thr
ea
ds
3. Avoid connecting ground lines to piping, as
this may cause electric corrosion of the
system.
4. Always tighten threads with the proper tightening torque.
When attaching fittings to valves, tighten with the proper tightening torque shown below.
Tightening Torque for Piping
Connection threads
Proper tightening torque N m
Rc 1/8
7 to 9
Rc 1/4
12 to 14
G 1/4
9 to 11
5. Connection of piping to products
When connecting piping to a product, refer to its instruction
manual to avoid mistakes regarding the supply port, etc.
Operating Environment
Warning
1. Do not use valves in atmospheres having
corrosive gases, chemicals, salt water, water, steam, or where there is direct contact
with any of these.
2. Do not use in locations subject to vibration
or impact.
3. Do not use in locations where radiated heat
will be received from nearby heat sources.
4. Employ suitable protective measures in locations where there is contact with water
droplets, oil or welding spatter, etc.
Take measures to prevent static electricity since some fluids
can cause static electricity.
Back page 2
Series VCC
Specific Product Precautions 2
Be sure to read this before handling. For Safety Precautions, refer to back page 1.
For Precautions, refer to “Precautions for Handling Pneumatic Devices” (M-03-E3A).
Maintenance
Caution
1. Filters and strainers
1) Be careful regarding clogging of filters and strainers.
2) Replace filter elements after one year of use, or earlier
if the pressure drop reaches 0.1 MPa.
3) Clean strainers when the pressure drop reaches 0.1
MPa.
2. Storage
In case of long term storage, clean after use with heated water and thoroughly remove all moisture to prevent rust and deterioration of rubber materials, etc.
3. Exhaust the drain from an air filter periodically.
Back page 3
Series VCC
Specific Product Precautions 3
Be sure to read this before handling. For Safety Precautions, refer to back page 1.
For Precautions, refer to “Precautions for Handling Pneumatic Devices” (M-03-E3A).
Design
Maintenance
Caution
Warning
1. Leakage detection port
The valve has a leak detection area to completely separate
the fluid area from the pilot pressure area. If leakage is found,
valve replacement and maintenance are necessary immediately. Fluids that solidify or cure may block the leak detection,
so port and leak may not be detected.
2. If applying high voltage to the fluid, it must
be earthed by using the bolt to mount the
base.
Do not use sealing tape when piping, as it may insulate.
1. Removing the product
1) Shut off the fluid supply and release the fluid pressure in
the system.
2) Dismount the product.
2. Low frequency operation
Switch valves at least once every 30 days to prevent malfunction. Also, in order to use it under the optimum state, conduct
a regular inspection once half a year.
3. Stoppage of line
When the line is stopped for a long time, clean the valve so
that fluid (paint, ink, etc.) does not solidify or get cured.
Selection
Caution
1. Operating fluid
Eliminate all solid material larger than 150 µm in the fluid to
avoid valve failure.
Piping
Caution
1. Piping to pilot port
Condensation may be formed in the piping to the pilot port,
due to factors such as its length. The life of the valve will be
shortened if condensed moisture enters the pilot port. To prevent condensation, the installation of a quick exhaust is recommended.
Lubrication
Caution
1. Do not lubricate the valve.
The valve uses white vaseline as lubricant.
Back page 4
Manifold Specifications
Series VCC
1. How to Order a Manifold
VV M CC1 06 10 C4 G04
q
w
q Type (Passage number)
2 port valve
2
3 port valve
3
M 2/3 port valves mixed mounting
e
r
t
∗ This “How to Order” is that of the example below.
w 2 port valve
mountable number Note 1)
00
02
04
r Pilot port fitting size
C4
C6
Without 2 port valve
2 pcs. (colours)
4 pcs. (colours)
ø4 one-touch fitting
ø6 one-touch fitting
40 40 pcs. (colors) Note 2)
t Gate valve and cleaning valve mountable number Note 1)
e 3 port valve
mountable number Note 1)
00
02
04
–
Without 3 port valve
2 pcs. (colours)
4 pcs. (colours)
Without gate valve Note 3)
Cleaning valve: 1 pc. + Gate valve: 1 pc.
Cleaning valve: 3 pcs. + Gate valve: 1 pc.
Cleaning valve: 5 pcs. + Gate valve: 1 pc.
G02
G04
G06
40 40 pcs. (colors) Note 2)
Note 1) Two valves can be installed per manifold block. Total valve number must be an even number.
Note 2) Maximum valve number is forty (40) valves (colours) by a total of w + e + t.
Note 3) When “Without gate valve” is selected, use 2 port valve of w as a cleaning valve.
2. How to Order a Valve
3. How to Order the Blanking Plug
VCC1 2 00
VVCC1 2 10A 1 VCK K 1075 02F
q
q
q Type (Passage number)
2
3
2D
4. How to Order the SUS316L Stainless Steel Fitting
q Type (Passage number)
2
3
2 port valve
3 port valve
2 port/Diaphragm type
q
q Type (Shape)
K
L
H
For 2 port valves
For 3 port valves
Used when the number of valves used on the manifold
base is an odd number.
w
w Piping port
1209
1008
1075
0806
0604
40° swivel elbow
90° swivel elbow
Male connector
Piping port for ø12 x ø9
Piping port for ø10 x ø8
Piping port for ø10 x ø7.5
Piping port for ø8 x ø6
Piping port for ø6 x ø4
Cleaning valve
with gate valve
Mountable number
∗ In this case, four (4)
cleaning valves
(including gate valve)
Stations
2
1
2 port valve
3 port valve
Mountable number
Mountable number
∗ In this case, six (6) 2 port valves
1
3
5
∗ In this case, ten (10) 3 port valves
1
3
5
7
9
Pilot port fitting
IN port
OUT port
D side
U side
IN port
Stations
3
Gate
Cleaning unit (with gate valve) side
Back page 5
2
4
6
Standard unit side
2
4
6
8
10
RETURN port
SMC Corporation
Manifold Specification Sheet (Series VCC: VVCC1)
 Fill in this format.
Date: Year _____ / Month _____ / Date _____
Company
name
Department
Person
in charge
Phone
Fax
Repeat
Device
description
Drawing
number
Production
number
 Repeat  Not Repeat
 Ordered part number (Please order with this part number.)
SMC use
Manifold valve part no.
C C 1- 0 0
V C C 1
 Valve
Specification Sheet
∗ Fill in the symbol for stainless steel fitting. For others, mark necessary items with a circle.
Cleaning unit Note 2)
(with gate valve)
Unit
Part number (Mountable valve
number)
G06 G04 G02
Stations Note 1)
4
2 port valve (Sliding type)
VCC12-00
2 port valve (Diaphragm type)
5
2
3
1
Gate
Standard unit
02
1
04
2
3
06
5
4
08
6
7
10
8
9
12
14
16
18
20
40
11
13
15
17
19
10
12
14
16
18
20
39
40
D side
Description/Model
2 port valve
Valve
options
To fill in the blanks  in the manifold number,
please refer to the symbols in the catalogue.
Select the valve referring to the specification
table.
-
V V
VCC12D-00
Blanking plug for 2 port valve
VVCC12-10A-1
U side (OUT port side)
 Manifold
Fitting Piping port
IN port
Part number (Mountable valve
number)
02
Stations Note 1)
1
3 port valve
Valve
Fitting
options
Description/Model
Note 3)
04
2
3
06
5
4
08
6
7
10
8
9
12
14
16
18
20
40
11
13
15
17
19
10
12
14
16
18
20
39
40
3 port valve (Sliding type)
VCC13-00
Blanking plug for 3 port valve
D side
VVCC13-10A-1
Piping port
IN port
U side (OUT port side)
Note 3)
Piping port
RETURN port
 Select stainless steel fitting for IN, RETURN port from the table below, and enter the symbol into the specification table.
Symbol
A
B
C
D
E
Description
For piping ø12 x ø9
40° swivel elbow
For piping ø10 x ø8
40° swivel elbow
For piping ø10 x ø7.5 40° swivel elbow
For piping ø8 x ø6
40° swivel elbow
For piping ø6 x ø4
40° swivel elbow
Part no.
Symbol
F
G
H
J
K
VCKK1209-02F
VCKK1008-02F
VCKK1075-02F
VCKK0806-02F
VCKK0604-02F
Description
For piping ø12 x ø9
Male connector
For piping ø10 x ø8
Male connector
For piping ø10 x ø7.5 Male connector
For piping ø8 x ø6
Male connector
For piping ø6 x ø4
Male connector
Part no.
VCKH1209-02F
VCKH1008-02F
VCKH1075-02F
VCKH0806-02F
VCKH0604-02F
 Fill in the model number in the table below for connecting the fitting to the OUT port. (See SUS316L stainless steel fitting type.)
For connecting the elbow union, the piping direction is on top (IN, RETURN port side).
OUT port Stainless steel fitting
V C K
-0 2 F
Note 1) Two valves can be installed per manifold block. Assign two valves in one square.
Note 2) Please order a cleaning unit when the gate valve is necessary.
Note 3) When the fitting is necessary for IN, RETURN port, please order by selecting the necessary stainless steel fitting symbol in the port of each station.
For 40° swivel elbow, the piping direction is on D side.
Serial No.
Customer/SMC use
Customer code
Department
code
Date of
delivery
U/C
Fill in for faxed order
Customer’s
order no.
Code for person
in charge
Registered
image no.
SMC order no.
Component list
Part no.
Qty.
Part no.
Qty.
Part no.
1
6
11
2
7
12
3
8
13
4
9
14
5
10
15
Qty.
Back page 6
Valve type
2 port valve
Valve arrangement
7 pcs.
3 port valve
24 pcs.
1 pc.
4 pcs.
Gate valve
Cleaning valve
C C 1- 0 0
V C C 1
ø8 x ø6 (40° swivel elbow)
ø10 x ø8 (90° swivel elbow)
One-touch fitting for ø4
∗ Specify twelve (12) stations for
manifold.
 Valve
Cleaning unit Note 2)
(with gate valve)
G06 G04 G02
Stations Note 1)
4
2 port valve (Diaphragm type)
5
2
3
1
Gate
Standard unit
02
1
04
2
3
06
5
4
08
6
7
8
VCC12D-00
Stations Note 1)
Description/Model
3 port valve
Valve
options
16
18
20
40
39
40
When more than twenty valves are used, specify valve qty. in
blank column. When the same valves and fittings are required,
they can be specified by arrows.
IN port
Part number (Mountable valve
number)
Fitting
14
Blanking plug for 2 port valve
VVCC12-10A-1
Note 3)
12
11
13
15
17
19
10
12
14
16
18
20
Although eight 2 port valves can be installed, if you need
only seven valves, select the blanking plug. The plug is
connected to the port with the blanking plug.
Fitting Piping port
Note 3)
10
9
D side
Description/Model
VCC12-00
Pilot port piping size
∗ Fill in the symbol for stainless steel fittings. For others, mark necessary items with a circle.
Part number (Mountable valve
number)
2 port valve (Sliding type)
To fill in the blanks  in the manifold number,
please refer to the symbols in the catalogue.
Select the valve referring to the specification
table.
-
V V
The upper table is for 2
Specification
port valves.
The lowerSheet
is for 3 port valves. Unit
Specify when the gate valve is necessary for cleaning the valve. This
example requires one gate valve
and four cleaning valves, but specify
“06” as the number of valves that
can be installed, as this must be an
even number.
When twenty-four (24) 3 port
valves are used, specify “24”.
nifold
 Manifold
2 port valve
Valve
options
IN port
OUT port
Pilot port
Seven (7) 2 port valves are installed. Since two valves are installed
per manifold base, it must be an
even number, so the number of
the valve that can be installed is
“08”. ∗ Specify four (4) stations for ma-
Put “M”, because 2
port valves (including
a cleaning unit) and 3
port valves are installed together.
Fitting arrangement
ø10 x ø8 (40° swivel elbow)
ø12 x ø9 (40° swivel elbow)
ø6 x ø5 (Male connector)
3 port valve (Sliding type)
VCC13-00
Blanking plug for 3 port valve
VVCC13-10A-1
Piping port
IN port
Piping port
RETURN port
U side (OUT port side)
Cleaning unit
IN port
IN port
RETURN port
02
04
06
08
10
12
14
16
18
20
40
Although six gate
valves or cleaning 1 2 3 4 5 6 7 8 9 10 1112 1314 1516 1718 1920
valves can be installed, if you need
only five
valves,
D side
select the blanking plug. The
plug is connected
to the port with
the blanking plug.
39
40
U side (OUT port side)
Condition
Manifold Specifications — Example of how to fill in
 Select stainless steel fitting for IN, RETURN port from the table below, and enter the symbol into the specification table.
Symbol
A
B
C
D
E
Description
For piping ø12 x ø9
40° swivel elbow
For piping ø10 x ø8
40° swivel elbow
For piping ø10 x ø7.5 40° swivel elbow
For piping ø8 x ø6
40° swivel elbow
For piping ø6 x ø4
40° swivel elbow
Part no.
Symbol
F
G
H
J
K
VCKK1209-02F
VCKK1008-02F
VCKK1075-02F
VCKK0806-02F
VCKK0604-02F
Description
For piping ø12 x ø9
Male connector
For piping ø10 x ø8
Male connector
For piping ø10 x ø7.5 Male connector
For piping ø8 x ø6
Male connector
For piping ø6 x ø4
Male connector
Part no.
VCKH1209-02F
VCKH1008-02F
VCKH1075-02F
VCKH0806-02F
VCKH0604-02F
 Fill in the model number in the table below for connecting the fitting to the OUT port. (See SUS316L stainless steel fitting type.)
For connecting the elbow union, the piping direction is on top (IN, RETURN port side).
OUT port Stainless steel fitting
V C K
-0 2 F
It must be specified
when the fitting is
to the
Note 1) Two valves can be installed per manifold block. Assign two valves in one square.
connected
Note 2) Please order a cleaning unit when the gate valve is necessary.
Note 3) When the fitting is necessary for the IN, RETURN port, please order by selecting the necessary stainless steel fitting symbol in the port of each station.
OUT port.
For 40° swivel elbow, piping direction is on D side.
Serial No.
Customer/SMC use
Customer code
Department
code
Date of
delivery
U/C
Fill in for faxed order
Customer’s
order no.
Code for person
in charge
Registered
image no.
SMC order no.
Component list
Part no.
Qty.
Part no.
Qty.
Part no.
1
6
11
2
7
12
3
8
13
4
9
14
5
10
15
2 port valve is specified for the gate valve and the cleaning valve.
7 valves + 1 valve + 4 valves = 12 valves
Back page 7
Qty.
24
EUROPEAN SUBSIDIARIES:
Austria
SMC Pneumatik GmbH (Austria).
Girakstrasse 8, A-2100 Korneuburg
Phone: +43 2262-62280, Fax: +43 2262-62285
E-mail: office@smc.at
http://www.smc.at
France
SMC Pneumatique, S.A.
1, Boulevard de Strasbourg, Parc Gustave Eiffel
Bussy Saint Georges F-77607 Marne La Vallee Cedex 3
Phone: +33 (0)1-6476 1000, Fax: +33 (0)1-6476 1010
E-mail: contact@smc-france.fr
http://www.smc-france.fr
Netherlands
SMC Pneumatics BV
De Ruyterkade 120, NL-1011 AB Amsterdam
Phone: +31 (0)20-5318888, Fax: +31 (0)20-5318880
E-mail: info@smcpneumatics.nl
http://www.smcpneumatics.nl
Spain
SMC España, S.A.
Zuazobidea 14, 01015 Vitoria
Phone: +34 945-184 100, Fax: +34 945-184 124
E-mail: post@smc.smces.es
http://www.smces.es
Belgium
SMC Pneumatics N.V./S.A.
Nijverheidsstraat 20, B-2160 Wommelgem
Phone: +32 (0)3-355-1464, Fax: +32 (0)3-355-1466
E-mail: post@smcpneumatics.be
http://www.smcpneumatics.be
Germany
SMC Pneumatik GmbH
Boschring 13-15, D-63329 Egelsbach
Phone: +49 (0)6103-4020, Fax: +49 (0)6103-402139
E-mail: info@smc-pneumatik.de
http://www.smc-pneumatik.de
Norway
SMC Pneumatics Norway A/S
Vollsveien 13 C, Granfos Næringspark N-1366 Lysaker
Tel: +47 67 12 90 20, Fax: +47 67 12 90 21
E-mail: post@smc-norge.no
http://www.smc-norge.no
Sweden
SMC Pneumatics Sweden AB
Ekhagsvägen 29-31, S-141 71 Huddinge
Phone: +46 (0)8-603 12 00, Fax: +46 (0)8-603 12 90
E-mail: post@smcpneumatics.se
http://www.smc.nu
Bulgaria
SMC Industrial Automation Bulgaria EOOD
16 kliment Ohridski Blvd., fl.13 BG-1756 Sofia
Phone:+359 2 9744492, Fax:+359 2 9744519
E-mail: office@smc.bg
http://www.smc.bg
Greece
SMC Hellas EPE
Anagenniseos 7-9 - P.C. 14342. N. Philadelphia, Athens
Phone: +30-210-2717265, Fax: +30-210-2717766
E-mail: sales@smchellas.gr
http://www.smchellas.gr
Poland
SMC Industrial Automation Polska Sp.z.o.o.
ul. Poloneza 89, PL-02-826 Warszawa,
Phone: +48 22 211 9600, Fax: +48 22 211 9617
E-mail: office@smc.pl
http://www.smc.pl
Switzerland
SMC Pneumatik AG
Dorfstrasse 7, CH-8484 Weisslingen
Phone: +41 (0)52-396-3131, Fax: +41 (0)52-396-3191
E-mail: info@smc.ch
http://www.smc.ch
Croatia
SMC Industrijska automatika d.o.o.
Crnomerec 12, 10000 ZAGREB
Phone: +385 1 377 66 74, Fax: +385 1 377 66 74
E-mail: office@smc.hr
http://www.smc.hr
Hungary
SMC Hungary Ipari Automatizálási Kft.
Budafoki ut 107-113, H-1117 Budapest
Phone: +36 1 371 1343, Fax: +36 1 371 1344
E-mail: office@smc.hu
http://www.smc.hu
Portugal
SMC Sucursal Portugal, S.A.
Rua de Engº Ferreira Dias 452, 4100-246 Porto
Phone: +351 22-610-89-22, Fax: +351 22-610-89-36
E-mail: postpt@smc.smces.es
http://www.smces.es
Turkey
Entek Pnömatik San. ve Tic. A*.
Perpa Ticaret Merkezi B Blok Kat:11 No: 1625, TR-34386, Okmeydani, Istanbul
Phone: +90 (0)212-444-0762, Fax: +90 (0)212-221-1519
E-mail: smc@entek.com.tr
http://www.entek.com.tr
Czech Republic
SMC Industrial Automation CZ s.r.o.
Hudcova 78a, CZ-61200 Brno
Phone: +420 5 414 24611, Fax: +420 5 412 18034
E-mail: office@smc.cz
http://www.smc.cz
Ireland
SMC Pneumatics (Ireland) Ltd.
2002 Citywest Business Campus, Naas Road, Saggart, Co. Dublin
Phone: +353 (0)1-403 9000, Fax: +353 (0)1-464-0500
E-mail: sales@smcpneumatics.ie
http://www.smcpneumatics.ie
Romania
SMC Romania srl
Str Frunzei 29, Sector 2, Bucharest
Phone: +40 213205111, Fax: +40 213261489
E-mail: smcromania@smcromania.ro
http://www.smcromania.ro
UK
SMC Pneumatics (UK) Ltd
Vincent Avenue, Crownhill, Milton Keynes, MK8 0AN
Phone: +44 (0)800 1382930 Fax: +44 (0)1908-555064
E-mail: sales@smcpneumatics.co.uk
http://www.smcpneumatics.co.uk
Denmark
SMC Pneumatik A/S
Knudsminde 4B, DK-8300 Odder
Phone: +45 70252900, Fax: +45 70252901
E-mail: smc@smc-pneumatik.dk
http://www.smcdk.com
Italy
SMC Italia S.p.A
Via Garibaldi 62, I-20061Carugate, (Milano)
Phone: +39 (0)2-92711, Fax: +39 (0)2-9271365
E-mail: mailbox@smcitalia.it
http://www.smcitalia.it
Russia
SMC Pneumatik LLC.
4B Sverdlovskaja nab, St. Petersburg 195009
Phone.:+7 812 718 5445, Fax:+7 812 718 5449
E-mail: info@smc-pneumatik.ru
http://www.smc-pneumatik.ru
Estonia
SMC Pneumatics Estonia OÜ
Laki 12, 106 21 Tallinn
Phone: +372 6510370, Fax: +372 65110371
E-mail: smc@smcpneumatics.ee
http://www.smcpneumatics.ee
Latvia
SMC Pneumatics Latvia SIA
Smerla 1-705, Riga LV-1006
Phone: +371 781-77-00, Fax: +371 781-77-01
E-mail: info@smclv.lv
http://www.smclv.lv
Slovakia
SMC Priemyselná Automatizáciá, s.r.o.
Námestie Matina Benku 10, SK-81107 Bratislava
Phone: +421 2 444 56725, Fax: +421 2 444 56028
E-mail: office@smc.sk
http://www.smc.sk
Finland
SMC Pneumatics Finland Oy
PL72, Tiistinniityntie 4, SF-02231 ESPOO
Phone: +358 207 513513, Fax: +358 207 513595
E-mail: smcfi@smc.fi
http://www.smc.fi
Lithuania
SMC Pneumatics Lietuva, UAB
Oslo g.1, LT-04123 Vilnius
Phone: +370 5 264 81 26, Fax: +370 5 264 81 26
Slovenia
SMC industrijska Avtomatika d.o.o.
Mirnska cesta 7, SLO-8210 Trebnje
Phone: +386 7 3885412 Fax: +386 7 3885435
E-mail: office@smc.si
http://www.smc.si
© DiskArt™ 1988
© DiskArt™
OTHER SUBSIDIARIES WORLDWIDE:
ARGENTINA, AUSTRALIA, BOLIVIA, BRASIL, CANADA, CHILE,
CHINA, HONG KONG, INDIA, INDONESIA, MALAYSIA, MEXICO,
NEW ZEALAND, PHILIPPINES, SINGAPORE, SOUTH KOREA,
TAIWAN, THAILAND, USA, VENEZUELA
http://www.smc.eu
http://www.smcworld.com
SMC CORPORATION
Akihabara UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, JAPAN Phone: 03-5207-8249 FAX: 03-5298-5362
1st printing MO printing MO 00 Printed in Spain
Specifications are subject to change without prior notice
and any obligation on the part of the manufacturer.