ADC500 / ADC500X
B/W CCD CAMERA
Operating Instructions
CAUTION
1.
2.
1.
2.
1.
2.
1.
2.
1.
2.
Please use correct power adaptor, DC12V (regulated), to operate this unit. The
power tolerance of this unit is DC 12V ± 10% (DC10.8V~13.2V), over maximum DC13.2V power input
will damage this unit.
Video output (BNC connector) of this unit should only be connected to a non-powered device . Please
check the wiring of video output before powering on. If the power is offered through video output cable,
the unit will be damaged.
請使用正確電源供應器 (DC12V 穩壓), 此產品可使用電壓範圍為 DC 12V ±10% (DC10.8V~13.2V), 超過
DC13.2V 會損壞此機器。
此產品 ”Video” BNC 接頭, 請勿接電源輸出類之設備。在提供電源前, 請確認接線正確性。 若電源㉂
“Video” BNC 接頭處輸入會損壞此產品。
本機に使用する電源装置はＤＣ１２Ｖ± 10% (DC10.8V~13.2V)の安定化電源をお使い下さい。13.2V 以上
の電圧を加えると本装置が破損いたします。
本装置の映像出力(BNC 接栓)は、電源を入れる前に、必ず電源が入っていない装置に接続されている事
を確認して下さい。もし、電源が加わると破損する可能性があります。
Por favor use el correcto adaptador de energía eléctrica DC12V (regulado) para operar esta unidad,
La tolerancia de energía de esta unidad es de DC12V± 10% (DC10.8V~13.2V). Sobrepasar el
máximo de DC13.2V de la potencia de entrada dañara esta unidad.
El connector BNC usado para la salida de video, solo debera ser conectado a un dispositivo sin
energia. Favor chequear el cableado de la salida de video antes de conectarlo. Si la potencia pasa a
traves del cable de salida de video, la unidad se dañara.
Bitte schließen Sie das Gerät mit dem Netzgerät (DC12V) an. Die Toleraz der Stromversorgung ist 12V
DC ± 10% (DC10.8V~13.2V). Abweichende Werte können zu Beschädigungen am Gerät führen.
Verbinden Sie den Video-Ausgang (BNC-Anschluß) nur mit Anschlüßen an denen keine Spannung
anliegt. Bevor Sie die Spannungsversorgung einschalten, überprüfen Sie bitte den korrekten Anschluß
des Video-Ausgangs. Falsche Anschlußbelegungen können zu Beschädigungen an den Geräten
führen.
WARNING:
TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
Thank you for choosing this high quality camera. Before attempting to connect or operate
this product, please read these instructions completely and carefully.
SPECIFICATION
ADC500 (EIA)
Pick up Element
Number of Pixel
ADC500X (CCIR)
1/3" B/W CCD image sensor
510(H) x 492(V)
500(H) x 582(V)
Resolution
380 TV lines
Min. Illumination
0.5 Lux / 50IRE, F1.2
S/N Ratio
More than 48dB
Electronic Shutter
1/60 to 1/100,000 sec.
Iris Mode
Load Impedance
1/50 to 1/100,000 sec.
EE type / AES - selectable
75 Ω
Lens Mount
C/CS mount changeable
Microphone
Yes
Sync. System
Internal
Power Source
DC12V+ 10%, Center pin (+) positive.
Current Consumption
Dimension (mm)
130 mA
108(L) x 62(W) x 50(H)
Weight
360 g
General
This Black and White CCD video camera employs a 1/3" charge coupled imaging device which provide
extremely long life and high reliability. The camera offers excellent reproducibility with low lag and high burn
resistance, and is not subject to distortion from magnetic fields.
Features
1. Horizontal resolution of 380 TV lines.
2. Built in Auto Electronic Shutter.
3. Minimum illumination of 0.5Lux/ 50IRE,F1.2.
4. Signal-to-noise ration of 48dB.
5. Long life and high reliability.
Warning -- This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, i f not installed
and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference
at his own expense.
Major Operating Control and Functions
AUDIO
PL
VIDEO
AI
AES
12V DC
1
3
2
4
1.12V DC
2.IRIS OUT
3.NC
4.GND
AUTO IRIS
1. Back Focus Flange Adjustment Ring
Suitable for CS-mount lens, For C-mount lenses use the included C conversion ring.
2. Back Focus Lock Screw
The camera is set at the standard back focus position.
Depending on types of lenses, however slight
adjustment may be necessary. Adjust the lens back-focus by turning the focusing knob.
3. Auto iris Lens Connector
Supplies power and control signals to an auto iris lens.
4.
AES/AI Selector
Lets you select the mode according to the lens type that is used with this camera.
AES: Select this mode when a fixed iris lens or manual iris lens is used with this camera.
AI:
5.
Select this mode when an EE auto iris lens is used with this camera.
DC12V Input Terminal
This terminal is for connecting the 12V DC regulated power supply. Center pin (+) positive.
6.
Power LED Indicator
The Power LED Indicator is lit during normal operation.
7. Audio Output Connector (AUDIO OUT)
This connector is for connecting with the AUDIO IN connector of the video monitor.
8. Video Output Connector (VIDEO OUT)
This connector is for connecting with the VIDEO IN connector of the video monitor.
Connections
1. Mount a lens onto the camera.
2. Set the lens selection switch (AES/AI) accordingly.
3. Connect a video terminal of the camera (VIDEO) and the video input terminal of the video monitor with a
75Ω coaxial cable.
4. Connect an audio terminal of the camera (AUDIO) and the audio input terminal of the video monitor.
5. Connect the power terminal of the camera to a 12V DC regulated power supply, center pin (+) positive.
Installation of Auto Iris Lens Connector
For Video auto iris lenses a connector modification may be needed. Verify lens pin-out against chart below.
This installation should be made by qualified service personnel or system installers.
If necessary, cut the iris control cable at the edge of the lens connector to remove the existing lens connector.
Open the supplied connector and solder the wires to the pins of the supplied connector as shown in the
diagram below.
The pin assignment of the auto iris lens connector is as follows:
VIDEO
Pin 1:
Power source
Pin 2:
Video signal
Pin 3:
Not used
Pin 4:
Ground, Shield
Back Focus Flange Adjustment
The following adjustment should be made by qualified service personnel or system installers.
1. Mount the lens by turning it clockwise on the lens mount of the camera.
2. Loosen the screws on the back focus adjustment ring.
3. Turn the back focus adjustment ring to the desired position.
4. Tighten the screws on the back focus adjustment ring.
Standard Accessories
HEX wrench - 1pc
C mount adaptor ring - 1pc
Iris header - 1pc
Instruction manual - 1pc
July, 2001
Part # 8000-2846-01, Rev. A
Sensormatic Electronics Corporation
951 Yamato Rd., Boca Raton Fl., 33431
(561) 989-7000