High Bay Lighting Control System
High Bay Lighting Control System for Industrial
Locations
User Guide
4.2
9100127214899 Revision B
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
1
Contents
High Bay Gateway Visual Overview ........................................................................................................ 4
Visual Overview .............................................................................................................................................................4
Getting Started ....................................................................................................................................... 5
Mounting & Placement ...................................................................................................................................................5
Additional Mounting Considerations ...............................................................................................................................5
Powering On the High Bay Gateway for the First Time ..................................................................................................6
Gateway Information Screen ................................................................................................................. 6
Features .........................................................................................................................................................................7
Network ................................................................................................................................................... 7
Configuring Internet Connection.....................................................................................................................................8
Wi-Fi Connection .................................................................................................................................... 9
Managing the High Bay Gateway with a Wi-Fi Enabled Device .....................................................................................9
Security ................................................................................................................................................. 10
Security Features ......................................................................................................................................................... 10
Pin codes ..................................................................................................................................................................... 11
Home Screen ........................................................................................................................................ 11
Software Features ........................................................................................................................................................ 11
System Time .......................................................................................................................................... 12
Time Configuration ....................................................................................................................................................... 12
Device Management ........................................................................................................................... 13
Adding/Removing Lights and Sensors ......................................................................................................................... 13
Device Management Visual ......................................................................................................................................... 16
Device Alert Notification ............................................................................................................................................... 17
GLOBAL (All Lights) Control ................................................................................................................... 18
How to Control Your Network ....................................................................................................................................... 18
Using the Global Control Bar Application ..................................................................................................................... 18
Configure a Global Lighting Schedule .......................................................................................................................... 19
Global Schedule Visual ................................................................................................................................................ 19
Groups .................................................................................................................................................. 20
Creating Groups ........................................................................................................................................................... 21
Creating Groups Visual ................................................................................................................................................ 21
Editing Groups ............................................................................................................................................................. 22
Editing Groups Visual................................................................................................................................................... 23
Controlling Groups ....................................................................................................................................................... 24
Controlling Groups Visual ............................................................................................................................................ 25
Configure a Group Schedule ........................................................................................................................................ 25
Group Schedule Visual ................................................................................................................................................ 26
Daylight Harvesting Sensor ................................................................................................................... 27
Using Daylight Harvesting Functionality ....................................................................................................................... 28
Daylight Harvesting Schedule Visual ........................................................................................................................... 29
Occupancy Sensor ............................................................................................................................... 30
Using Occupancy Sensing Functionality ...................................................................................................................... 31
Occupancy Sensor Visual ............................................................................................................................................ 31
Settings ................................................................................................................................................. 32
Cloud Setup ................................................................................................................................................................. 33
Software Updates......................................................................................................................................................... 33
Change Wallpaper ....................................................................................................................................................... 33
Download Map ............................................................................................................................................................. 34
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
2
Backup Management ................................................................................................................................................... 34
User Management........................................................................................................................................................ 35
Login Screen ......................................................................................................................................... 35
Pin Code ...................................................................................................................................................................... 35
Emergency Override .................................................................................................................................................... 35
Cloud Server ......................................................................................................................................... 36
Cloud Server ............................................................................................................................................................... 36
Viewing the gateway on the cloud. ............................................................................................................................... 37
Editing High Bay Gateway ........................................................................................................................................... 38
Cloud Visual Overview ................................................................................................................................................. 39
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
3
High Bay Gateway Visual Overview
Visual Overview
High Bay Gateway hardware features:
2.4Ghz Antenna /
SMA Connector
Ambient Light Sensor
and
Occupancy Sensor
Screen
Integrated Wall Mount
Sealed RJ45 Connector
Sealed AC Power
connector
In the box
1x – High Bay Gateway
1x – Sealed AC power connector assembly
1x – Sealed RJ45 network connector assembly
1x – Antenna
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
4
Getting Started
Mounting & Placement
For best screen visibility, avoid
mounting the high bay gateway
in direct sunlight.
!
100ft max distance to first High Bay
light.
High Bay Gateway should be placed in close
proximity to the controlled High Bay lights to
optimize Daylight Harvesting mode
operation.
!
Power / Dali
Recommended
mounting height:
4.5 – 5.5ft.
Ethernet port
Additional Mounting Considerations
The high bay gateway should not be mounted in wet zones or exposed to extreme
moisture conditions.
For optimal performance the high bay gateway should have direct line of sight (LoS) to
at least one light fixture to be controlled.
For best occupancy detection performance, mount near an entryway to the lighted
area.
Ensure that the mounting bolts are securely fastened to a solid backing.
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
5
Powering On the High Bay Gateway for the First Time
The high bay gateway doesn’t have an external power switch; it will automatically turn
on when power is connected.
1. Connect the high bay gateway to an active power source.


Connect Black lead to Line Voltage, White lead to Neutral and Green to ground
Or
Connect Brown lead to Line Voltage, Blue lead to Neutral, and Green to ground
2. Once power has been applied wait for the high bay gateway to load.
3. Once screen appears you can control your high bay gateway via Wi-Fi or Ethernet connection.
Gateway Information Screen
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
6
Features
The high bay gateway screen gives you current stats of your high bay system
performance.
Wired Network Status – Here
you’ll find the current IP address
as well as the static or DHCP
mode and the connection
status.
Wi-Fi Access – This panel
displays your high bay
gateway’s SSID and the
Wi-Fi IP address.
Lighting Override –
This button allows
you to manually
override any system
schedules or events.
It also allows you to
quickly turn on your
lighting network to
100% capacity
during an
emergency event.
Lighting Status – This panel displays real time data
regarding your lighting network
Network
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
7
Configuring Internet Connection
The network section under “Settings” allows you to control your DHCP or Static IP
configuration and your Wi-Fi Hotspot settings. If you use a static or DHCP address and
connect to your local network, then you can browse to the high bay gateway from any
computer on the network with a web browser. (Google Chrome browser is
recommended.)
Connecting DHCP
1. Verify your high bay gateway is plugged into the Ethernet port (Note: By default your
gateway is set to DHCP configuration.)
2. At the high bay gateway identify the DHCP address on the top right corner.
3. With a computer, connect to your local network.
4. Once connected, go to your web browser and enter the DHCP address of your
gateway.
5. You will then be directed to the login screen for your gateway. ( When logging in for
the first time, the default master pin code is set to: 1234)
Setting a Static IP: (Note: By default your gateway is set to DHCP configuration.)
1. Verify your high bay gateway is plugged into the Ethernet port.
2. Select “Network” from the settings screen.
3. Under the column “Ethernet TCP/IP Connection, choose the “Configure” button.
4. Switch from DHCP to Static by selecting the “Static” button on the right.
5. Click the fields to configure the appropriate IPAddress, Netmask, Gateway, DNS 1,
and DNS 2 for your high bay gateway. (If needed, please consult your IT advisor when
configuring your Static IP for the appropriate information for your organization’s internal
network.)
6. Select the “Save” button when done.
Setting up DHCP:
1. Verify your high bay gateway is plugged into the Ethernet port.
2. Select “Network” from the Settings screen.
3. Under the column “Ethernet TCP/IP” Connection, choose the “Configure” button.
4. Switch from Static to DHCP by selecting the “DHCP” button on the left.
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
8
5. Select the “Save” button when done.
6. The DHCP setting enables a server to automatically assign an IP address for your
gateway. (If you’re currently configuring from a computer, go to the high bay gateway to view the
new IP address.)
Wi-Fi Connection
Managing the High Bay Gateway with a Wi-Fi Enabled Device
A Wi-Fi Hotspot enables you to connect to a high bay gateway from a Wi-Fi enabled
device, like a tablet or mobile phone.
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
9
Accessing the High Bay Management Interface from your Wi-Fi Enabled Device:
1. Scan for available Wi-Fi networks with your Wi-Fi device and connect to the high
bay gateway SSID Wi-Fi network.
 This can be found in the top left corner of the high bay gateway screen.
2. Enter the password shown in the “Network” page.
 To view this password you must connect to your High Bay Gateway IP directly.
See Network Connections on page 7 to learn how. (When connecting for the first
time, the default Wi-Fi password is: highbaywc)
3. Open a web browser on your device.
4. Enter the IP address of the high bay gateway in your device’s web browser.
 By default the IP is 10.10.0.1
5. Once connected to the given IP address, the home screen should display and you
can begin controlling your high bay gateway via Wi-Fi.
Wi-Fi Hotspot Configuration:
1. Select Network from the Settings screen.
2. Under the Wi-Fi Network column select “Configure.”
3. Create a unique Access Point (SSID) name for your gateway’s hotspot. (This will help
distinguish one high bay gateway from another when choosing a high bay gateway from a list of WiFi networks later.)
4. Choose a desired Wi-Fi Channel from the drop down menu.
5. Create a passphrase.
6. Choose the “Save” button when done.
Security
Security Features
Security features help protect the high bay gateway from being accessed by
unauthorized individuals.
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
10
Authorized users have full access of the entire system or a specific section of the
system whichever you choose.
There are three control sections: Group Control, Global Control, and Settings.
Pin codes
For security, you will be asked to set up a passcode that you must enter to gain access
and control your lighting network. It’s recommend that a unique passcode be setup for
every user added in the system.
When logging in for the first time, the default master pin code is set to: 1234
Changing Master Pin code:
1. Go to Settings.
2. Choose the “User Management” button on the bottom left.
3. Select Dialight user.
4. Edit desired name and passcode.
5. Select “Save” to save your changes.
6. Press the “Home” button on the top left corner to return home.
(Note: This Master user can never be deleted.)
Home Screen
Software Features
The home screen has 2 main parts:
Information Bar – This quick information bar shows you: Current Light Dim Values,
Current Light Control Mode, Time and Date, and the Home and Logout navigation
buttons.
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
11
Main Menu – This menu directs you to the main branches of the system. The
application menu is separated into 3 main parts: Group Control, Global Control, and
Settings.
At any time, you can return to the application menu by clicking the home icon on the
top left corner from any of the application pages.
Global Control on mode with
current light level or Group
Control on mode
Home
Button
Daylight Harvesting on/off mode with
current dim level
Occupancy Sensing on/off mode
with step sequence timer
Current
Time
Logout Button
Information Bar
Main Menu
System Time
Time Configuration
Setting the System Time:
1. Select Time/Zone/Date button.
2. Choose your desired Time Configuration method:
Auto Sync - will sync time automatically with an NTP server via Internet
connection.
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
12
3. Select the GMT time zone for your area from the drop down menu on the left.
4. Once the GMT time zone has been selected, choose the corresponding time
zone location for your area from the drop down menu on the right.
5. Select “Save Configuration” to save your time.
Manual – allows user to customize their desired time output.
6.
7.
8.
9.
Set the time zone described in step three and four.
Use the right and left arrows to set the desired hour and minute output.
Use the drop down menu to set the desired year, month, and date.
Select the “Save Configuration” icon to save the manual time configuration.
Device Management
Adding/Removing Lights and Sensors
Device Management manages all your lights and sensors in your high bay gateway
network. From here you can add and remove lights and sensors from your gateway
while also allowing you to identify lights and their location.
Adding Lights to the High Bay Gateway:
Choose which lights you would like to manage: Wireless Devices or DALI Devices
For Wireless Devices:
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
13
1.
2.
3.
4.
5.
6.
Select Manage.
Turn off all undiscovered lights in the building.
Turn on discovery.
Turn power on to the lights you want to add to the high bay gateway.
Wait for all lights to be discovered and populate in a list.
Turn off Discovery.
For DALI Devices:
1.
2.
3.
4.
Select Manage.
Click “Discover All” button to discover all DALI lights for a new network install.
The discover buttons will gray out while DALI lights are being discovered.
Once the DALI lights have been discovered the buttons will go back to normal state
and the lights will populate in the list.
5. Once your initial DALI network has been discovered, any additional lights you would
like to add can be done with the “Discover Added” button.
(NOTE: If you choose “Discover All” instead of “Discover Added” all your DALI lights will be deleted
and all the DALI lights in your network will be re-commissioned as new. You will lose ALL lights
associated with your groups and schedules.
Identifying Lights:
1. Choose a light from the list of lights after discovery is complete. A popup window
will appear
2. Select the “Identify Light” Button from the popup window. (Light will begin flashing)
3. “Stop Identify” when ready and the light will go back to its current dim value
4. Close popup window when done.
Delete Lights:
1. Select a light from the list and a popup window will appear.
2. Select the “Delete Light” button.
3. Press the X to confirm your deletion.
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
14
Adding Sensors to the High Bay Gateway:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Install the sensor in your desired location.
On the gateway choose “Devices” from the “Settings” main screen on the left.
Select “Manage Wi-Fi Devices”.
Turn on “Discovery”.
Turn on the sensor.
Wait for the sensor to be discovered and populate on the discovery panel.
Turn off Discovery.
Select the sensor from the discovered list and a popup window will appear.
From the pop window you can rename your sensor for easy identification.
Repeat the steps above for each sensor.
Deleting Sensors:
1. Select a sensor from the discovered list and a popup window will appear.
2. Select the “Delete” button.
3. Press the X to confirm your deletion.
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
15
Device Management Visual
Discovery
Button
Discovered Occupancy
Sensors (Blue) – When the
desired sensor is selected a
popup window will appear
for more details.
Discovered
High Bay Light
(yellow)
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
16
Device Alert Notification
If your device(s) loses communication for any reason your gateway will promptly notify
you with an alert flag as seen below.
The alert flag will be shown in
every header along with the
number of devices with
active alerts.
This alert flag will also notify you when a sensor’s battery voltage falls below the 1.5v
threshold and the battery needs to be replaced.
When the alert flag is clicked, you’ll be directed to the device page. All devices
marked with an alert will be highlighted in red.
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
17
GLOBAL (All Lights) Control
Global Control allows you to control all your lights together. From here you can turn
on/off and dim your lights, create global schedules, and adjust daylight harvesting and
occupancy sensing settings.
How to Control Your Network
The Control Bar application allows a user to quickly and easily set the current light
output level of all lights managed by the high bay gateway.
If lights are currently being controlled by a schedule, you can quickly override it using
the manual on/off/dim controls.
At any time you can resume the schedule by selecting the resume button on the left.
Dimming Bar
On/Off
Control
Schedule Resume
Using the Global Control Bar Application
Turning Lights On/Off:
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
18
1. Click “Home” button to the top left.
2. Select the “Global Control” button.
3. Select the power button on the right to Activate/Deactivate the lights.
Dimming:
4. Click the + / - buttons of the dimmer bar in the middle to increase/decrease the
light output levels.
Note: If a manual lighting control override is made, keep in mind if harvesting schedule
events are turned on the lights may adjust to those settings.
Configure a Global Lighting Schedule
Global Control Schedule:
1. Select “Home” button to the top left.
2. Choose the “Global Control” button.
3. Select the “Schedule” button.
4. Click the “Add or Edit this Schedule” button.
5. Select a schedule output type: (You can choose one or all three in a given day for
your schedule.)
a. Dimmer event allows the lights to be manually dimmed at a certain time.
b. Harvesting event allows the lights to automatically adjust based on the
measured light parameters given for an allotted time specified.
c. Occupancy event allows the lights to be controlled by movement in a
room and will adjust light output based on the occupancy sequence
given.
6. Select the desired light output (DIM) level using the right/left arrow buttons. Min
0% (OFF) - Max 100% (For Dimmer Events Only)
7. Select the event hour and minute you would want the event to occur by using
the right/left arrow buttons. Press the add button to add the event.
8. As events are added to the schedule, a schedule list will populate on the right
side of the screen. Also, the chart in the middle of the screen gives you a visual
of what your schedule looks like for the day as events are added. (To delete an
event select the red x next to the event you would like to delete from the event list.)
9. When you are satisfied with your schedule select “Save Schedule” to save the
schedule.
Global Schedule Visual
Schedule Output Type
Event
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
19
List
Save the Schedule
Groups
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
20
Lights and sensors can be categorized and arranged into groups for convenient
independent lighting schedules.
Creating Groups
1. Activate “Group Control” from the Main Menu on the Home Screen by clicking on
the “Active” button.
2. Click the “Group Control” button.
3. Select the “Create Group” button from the list of group options.
4. Create your group name in the name field provided. (Creating a name helps identify the
group of lights and sensors that you want to control later)
5. Select your desired communication settings by choosing “Wireless” or “Dali”, from
the drop down menu on the right.
6. The “Unassigned” list on the left displays all available lights and sensors in the system
to add to the new group. Start by clicking on a light or sensor you would like to add
and a popup window will appear.
7. Click the “Add” button in the popup window to add the desired light or sensor.
8. Close popup window when done.
9. Repeat steps above to add additional sensors and lights.
10. Once all desired sensors and lights are chosen click “Save” and your new group will
be added.
11. At any time you can cancel your group creation by selecting the “Cancel” button.
Creating Groups Visual
Group Name Field
Communication
Dropdown List
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
21
Sensors and
lights will
populate on the
members list as
they are added
to the group.
The unassigned list displays all
available sensors and lights to
choose from to add to a
group.
Cancel
button will
cancel the
group
creation.
Save button will
save the group.
Editing Groups
Select “Group Control” from the Application Menu on the Home Screen.
1. Click the “Edit Group” icon.
2. Select the Group to edit.
3. Edit the Group Name in the name field on the top right. (If desired)
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
22
4. To remove an existing light or sensor, select desired light or sensor from the
“Members” list on the right and a pop window will appear.
5. Click the “Remove” button and the light or sensor will be removed.
6. Close pop window when done.
7. To add a new light or sensor, click the desired light or sensor from the “Unassigned”
list and a pop window will appear.
8. Click the “Add” button and the occupancy sensor will be added.
9. Close pop window when done.
10. Click “Save”.
Note: Occupancy sensors can only be assigned to one group.
Editing Groups Visual
Group Name Field
Communication Dropdown
List
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
23
Sensors and
lights will be
added or
removed from
the members
list as they are
added or
removed from
the group.
The unassigned list displays all
available sensors and lights to
choose from to add to the
group.
Removed sensors and lights will
repopulate on this list.
Delete
button will
delete the
group.
Save button will
save the group
edits.
Controlling Groups
1.
2.
3.
4.
5.
Select “Group Control” from the Main Menu on the Home Screen
Click the “Control Group” icon
Choose the group you want to control
That group will be highlighted and the control bar will appear
Now you may turn on / off / dim or schedule your group
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
24
6. Click in any open space to exit controlling the group
Note: If a manual lighting control override is made, keep in mind if harvesting schedule
events are turned on the lights may adjust to those settings.
Controlling Groups Visual
Adjust occupancy settings.
Adjust
daylight
harvesting
settings.
Create/edit a group
schedule.
Manually dim grouped lights.
Manually
turn grouped
lights on/off.
If the group is in manual override. A
group schedule can be resumed when
this button is pushed.
Configure a Group Schedule
Begin on the Group Control Screen:
1. Choose the group you want to add or edit a schedule for.
2. Select “Scheduling”
3. Select the “Add or Edit this Schedule” button
4. Choose your schedules output type. You can choose one or all three in a given
day for your schedule.
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
25
a. Dimmer event allows the lights to be manually dimmed at a certain time.
b. Harvesting event allows the lights to automatically adjust based on the
measured light parameters given for an allotted time specified.
c. Occupancy event allows the lights to be controlled by movement in a room
and will adjust light output based on the occupancy sequence given.
5. Select a light output (DIM) level using the right/left arrow buttons. Min 0% (OFF) - Max
100% (Only available in dimmer mode.)
6. Select the event hour and minute you would want the schedule output type to
occur by using the right/left arrow buttons. Press the add button to add the event
7. As events are added to the schedule, a schedule list will populate on the right side
of the screen. Also, the chart in the middle of the screen gives you a visual of what
your schedule looks like for the day as events are added. (To delete an event select
the red x next to the event you would like to delete from the event list.)
8. When you are satisfied with your schedule select “Save Schedule” to save the
schedule
Group Schedule Visual
Event List
Dimming
Level or
ON/OFF
26
Control
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
Schedule
Output Type
Save the Schedule
Daylight Harvesting Sensor
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
27
The high bay gateway is equipped with an innovative sensor technology which allows
you to save energy when natural daylight is present. The high bay gateway can also
communicate with individual daylight harvesting sensors that are placed throughout
your facility.
Once the user has selected the desired light level, the high bay gateway will
automatically increase/decrease the lumen output of the lights in order to maintain the
desired light level. (When daylight harvesting mode is activated, scheduled dimmer
events are overridden.)
Using Daylight Harvesting Functionality
Adjust Daylight Harvesting Settings:
1. Select ‘Harvesting Settings’ from the Global Control Menu or Group Control Menu for
a desired group.
2. Set the desired light level threshold by selecting the Right/Left arrow buttons until
your desired light level is displayed on the screen.
3. If there’s more than one daylight harvesting sensor connected to a group, choose
the desired multi sensor mode.
 If you want your lights to automatically adjust to the lowest daylight
harvesting sensor reading within a room then choose LO from the Multi
sensor Mode.
 If you want your lights to automatically adjust to the highest light level sensor
reading within a room than choose HI from the Multi sensor Mode.
 If you want your lights to automatically adjust to the average light output
within a room based on the sensor readings then choose AVG from the Multi
senor Mode.
4. Click the ‘Save Changes’ icon.




Suggested procedure for setting your target light level.
At night, go to the high bay gateway and login
Click “Global Control” and turn on all lights to 100%
Once all lights are on at full capacity Click “Harvest Settings”
On the bottom left read the “Current Light Level”
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
28

Once you know the light level in the room, you can keep this light consistency
throughout the day by setting your desired light level to match the current light level in
the room.
 Click “Save Desired Light Level”
Note: You will need to do this procedure with every high bay gateway within your facility for light level
consistency.
Adding a Harvesting Event to Schedule
1. Select the “Schedule” button.
2. Choose the “Add or Edit this Schedule” icon.
3. Select the “Harvest” button on the left of the screen.
4. Create an On Time and select add.
5. Create an Off Time and select add.
6. See the on/off events populate to the event list and graph.
7. When you’re satisfied with your schedule click “SAVE SCHEDULE” to save the
schedule.
Daylight Harvesting Schedule Visual
Event graph shows a visual
of the occupancy events for
a 24 hour day
Event list
shows desired
On/Off times
for occupancy
control.
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
29
Harvest sensor
Add button will
add the event to
the event list.
Create a Daylight
Harvesting On and
Off time here
Save schedule will
save the group
schedule.
Set the desired
times of when you
would like
occupancy sensor
On or Off
Occupancy Sensor
The integrated occupancy sensor allows the lights to be activated when a person
walks by the high bay gateway or a standalone occupancy sensors regardless of
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
30
scheduled events. The occupancy sensor mode can be configured to return to its
normal schedule gradually in a user-defined sequence.
Using Occupancy Sensing Functionality
Configure Occupancy Sensor Settings:
1. Click “Occupancy Settings” from the Global Control Menu or Group Control Menu
for a desired group.
2. Set the desired dim percentages of your lights when the sensor has been triggered
by selecting the right/left arrow icons for each lighting level until the desired time for
each level is displayed on the screen.
3. Set the desired time span for each dim level for how long you would like each dim
event to last for by selecting the Right/Left arrow icons.
4. Click the “Save Changes” icon on the screen.
Add an Occupancy Sensing Event to Schedule:
1.
2.
3.
4.
5.
6.
7.
8.
9.
From the Group Control main screen, select “Control Group.”
Select a desired group to control.
Select the “Schedule” button.
Choose the “Add or Edit this Schedule” icon.
Select the “Occupancy” button on the left of the screen.
Create an On Time and select add.
Create an Off Time and select add.
See the on/off events populate to the event list and graph.
When you’re satisfied with your schedule select “SAVE SCHEDULE” to save the
schedule.
Occupancy Sensor Visual
Event graph shows a visual
of the occupancy events for
a 24 hour day
Event list
shows desired
1501 Route 34 South, Farmingdale, NJ 07727
On/Off times
for occupancy
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
control.
31
Occupancy
sensor
Create an
occupancy On
and Off time
here
Add button will
add the event to
the event list.
Save schedule will
save the group
schedule.
Set the desired
times of when you
would like
occupancy sensor
On or Off
Settings
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
32
Cloud Setup
Your high bay gateway has the ability to communicate with a centralized cloud server.
This will enable you to view and operate your high bay gateway remotely.
Cloud Configuration Setup:
1.
2.
3.
4.
5.
6.
7.
8.
Select “Cloud Setup” under settings.
Add your cloud’s IP address.
Add your port number.
Add a Location ID to easily identify your gateway on the cloud.
Click save.
Go to your cloud.
Login with your username and password.
Verify your NEW high bay gateway has been populated on the dashboard page of
the cloud.
9. Select the high bay gateway and you can now control it remotely.
Software Updates
Periodically a new software update may be available. Updates may include new
features, configuration changes, and general updates to your high bay gateway.
To Check for Updates: If an update is available you’ll be sent a downloadable file
to add to your high bay gateway. (Note: The steps below should be done with a computer or
1.
2.
3.
4.
laptop.)
From the general tab under settings, choose the “Update” button.
Select the “Choose File” button and select the downloaded file you were given.
Select Upload and your high bay gate will begin adding the new upgrade.
Once the upgrade is complete your high bay gateway will be rebooted
automatically for the changes to take effect. (Note: Upgrades won’t interfere with
your current lighting network parameters, schedules, or group.
Change Wallpaper
The wallpaper feature gives you the ability to customize the background of your wall
control.
Upload and Change Wallpaper Background:
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
33
1.
2.
3.
4.
Go to the high bay gateway’s remote cloud management web page on a server.
Sign-in to cloud.
Under the “Configuration” menu, select “Wallpaper.”
Select “Choose File” and choose your desired wallpaper.
(Note: Be cautious when choosing light or white colored backgrounds that can distort the display
text.)
5. Select “Upload.”
6. Go back to the high bay gateway to add wall paper.
7. Select the “Change Wallpaper” button from the settings screen.
8. Your new wallpaper should appear from the list to choose from.
9. Select the wallpaper and the High Bay Gateway will automatically reboot.
10. Once reboot is complete the new wallpaper should appear on the Gateway.
Download Map
How to Download a Map:
(Similar steps as above)
1. Go to the high bay gateway’s remote cloud management.
2. Sign-in to cloud.
3. Under the “Configuration” menu, select “Lighting Maps.”
4. Select “Choose File” and choose your desired map.
5. Select “Upload”.
6. Go back to the high bay gateway to add your map.
7. Choose the “Download Map” button from the settings screen.
8. Your new map should appear from the list to choose from.
9. Select the map.
10. Go to Group Control from the Main Menu.
11. Choose “Lighting Map” and your new map should be displayed.
Backup Management
Backup Management allows you to save ALL your current settings, schedules, groups,
and configurations within the high bay gateway.
Creating a Backup:
1. Select the “Create” button from the Actions column on the right.
2. The backup will populate on the list and be labeled with the current date.
Restore Backup:
1. Choose the desired backup from the list.
2. Select the “Restore” Button.
3. Select “Okay” to confirm your backup from the popup window.
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
34
4. Your Backup has now been restored.
User Management
Add Users to the System:
Settings users have the ability to add other users to the system and change system
settings.
1. Select the “User Management” button from the Settings screen.
2. Click “Create User” on the top right corner to add a new user to the system.
3. Enter the:
o Username
o PIN Code (The pin code is used to access system from the log-in screen)
o Re-Enter the PIN code to confirm
o Select the desired user access privileges by checking the box next to
each section
4. When complete select the “Submit” icon to return to the Settings
screen.
Login Screen
Pin Code
Using Pin Code:
1. From the login screen use the number pad to enter your user pin code.
2. Select the “Login” button.
Emergency Override
In case of an emergency, the emergency button allows all lights to be turned on
immediately to 100% light output when no user is logged in.
How to Use Emergency Override:
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
35
1.
2.
3.
4.
From the login screen click the emergency override button.
All lights will turn on to 100% and will stay until the override has been shut off.
To shut off override, Go to the high bay gateway and select the “Off” button.
All lights will then return to their last scheduled event.
Cloud Server
Cloud Server
The cloud server acts as a central management portal for one or more high bay
gateways that can be located at multiple facilities. The cloud portal can be securely
accessed from a web browser.
Server Requirements:
Minimum -
2.0Ghz Single Core or Faster CPU (64 bit)
512MB RAM
10GB Disk or more
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
36
Recommended -
Dual-Core CPU or better (64 bit)
1GB RAM
15GB Disk or more
Once you have installed your gateway for the first time, you’ll be able to connect it to
the high bay cloud easily with auto registration. After your gateway is registered you
can conveniently monitor and control your high bay gateway remotely.
Viewing the gateway on the cloud.
After your high bay gateway has been assigned a cloud IP, you can now view and edit
and control your gateway from the cloud.
Viewing gateway on cloud:
1. Using an internet browser, go to your cloud’s IP address.
2. Once there login with your given login credentials.
3. You will then be directed to the dashboard page after login.
4. Your new gateway will be populated on the list of gateways on the right.
5. From this list you can see your gateway’s current state and IP address and when
selected you will be directed to the gateway’s control screen.
Status Key:
GREEN = gateway is communicating
1501 Route 34 South, Farmingdale, NJ 07727
Tel:
(732)
919-3119
Fax: (732) 751-5778 www.dialight.com
Red = gateway communication error
37
This can be due to a power outage or internet
communication issue.
Gray = gateway is sitting idle click the refresh
icon
to get current status.
Editing High Bay Gateway
Now that your high bay gateway has been added to the cloud, you can now reassign
a name to it for easy identification and change the gateway’s IP address as desired.
Renaming Gateway:
1. Login to the cloud.
2. From the Dashboard page, select the High Bay Gateway configuration menu
and choose “Gateways”.
3. Choose the desired gateway on the right and select it.
4. In the text field on the left of Location Name, choose your desired new name for
your gateway.
Changing Gateway IP:
1. Login to the cloud.
2. From the Dashboard page, select the High Bay Gateway configuration menu
and choose “Gateways”.
3. Choose the desired gateway on the right and select it.
4.
In the text field on the left of IP Address, choose your desired new IP address for
your gateway and port if needed.
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
38
Cloud Visual Overview
Visual Overview
High Bay Cloud software features:
Company
Logo
Configure new high bay gateways,
edit gateways, and add maps or
wallpapers in the “High Bay
Gateway Configuration” menu.
Login
Credentials
Create users and change your desired logo in
the “System Settings” menu.
High Bay
Gateway totals
counter.
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
39
Dashboard visual of all high bay
gateways in your facility
network.
Operating parameters



Product Ambient temp range: -40°C to +65°C
Input: 100-277VAC 50/60 Hz, 20W
Peak Current: 200mA
Ratings and Certifications




This equipment has been evaluated to UL 916, Standard for Safety Energy
management Equipment, CSA C22.2 No. 205, Signal Equipment.
CE compliant
RoHS compliant
For use in non-hazardous locations only.
1501 Route 34 South, Farmingdale, NJ 07727
Tel: (732) 919-3119 Fax: (732) 751-5778 www.dialight.com
40