(QSNE-4A-D)
IMPORTANT NOTES
ww
co
m
1. Manual Programming: This document describes manual
programming via the buttons on the front of the Energi Savr
NodeT unit. For programming using the Apple iPod touch or
iPhone mobile digital devices, please see the Energi Savr app
available from the Apple AppStore online marketplace.
2. Only use compatible LutronR sensors and controls.
Energi
Savr
NodeT
(ESN)
Unit
w. l u t r o n .
Lutron GL LTD
+65.6220.4666
+65.6220.4333
www.lutron.com/asia
This guide is divided into sections
to . Each section deals with
a particular feature or set of features of the ESN and the equipment
connected to it. Depending on the connected equipment and the
intended use of your ESN, some sections may not apply. See below
to determine which sections should be read.
S4
CCI
Zone 1 Zone 2 Zone 3 Zone 4
Type
Hi Temp
Prog
Power
QSNE-4A-D
DIN Rail Power Module
Photo Occ Switch
Option
Def
H
Opt1
M
Opt2
L
Input
Hi Temp
Prog
Power
Option
Def
M
Opt2
L
QS
Sensor »
Module
»
S4
CCI
Energi Savr
NodeT (ESN)
Unit
Zone 1 Zone 2 Zone 3 Zone 4
ESN Wired Input Setup
Hi Temp
Prog
Power
QSNE-4A-D
Photo Occ Switch
DIN Rail Power Module
IR
Input
230 V~ 50 / 60 Hz 10 A
Option
Def
H
Opt1
M
Opt2
L
Opt3
www
www.lutr
on.com +44.(0)20.7702.0657
www.lutron.com
Emergency
Dry Contact
Closure Input
800 W Max 800
500WWMax
Max 500
500WWMax
Max 500
500WWMax
Max 500 W Max
Input
S1
Input
S2 S1
S3
IR
Photo IR
OccPhoto
Switch
Occ Switch
S2
S4
S3
CCI S4
CCI
Zone
1 Zone
Zone12 Zone
Zone23 Zone
Zone34 Zone 4
Prog
Prog
Infrared (IR)
Sensor
-or-
H
Opt1
M
M
Opt2
Opt2
L
L
Opt3
Opt3
»
»
Subsection: Assign Zones to
QSM Inputs
»
Wired
Daylight
Sensor
Dry Contact
Closure Switch
Wires to multi-function
Input
»
ESN Wired
Input Setup
ESN Wired
Input Setup
Wires to multi-function Input
»
ESN Wired Input Setup
LUTRON
Wires to multi-function Input
»
Daylighting Setup
»
Subsection: Assign Zones to
QSM Inputs
Unit was overheated and has now cooled
to acceptable temperature
“Prog”
(Program)
Off
Device in Normal Mode
Flashing: 1 blink/sec
Device in Program Mode
“Zone 1-4”
Off
Normal Operation: zone off
Continuous On
Normal Operation: zone on
1 blink, pause
Output shorted: verify wiring and do one
of the following to turn on affected zone:
- Press affected “Zone” button then
press
to raise on the unit
- Press a scene button on a connected
QS device
- Press Reset button next to CCI terminal
- Power cycle unit
2 blink, pause
Overvoltage: contact Lutron
3 blink, pause
Shorted component: contact Lutron
4 blink, pause
Overtemperature: zone may be
overloaded, all loads scaled to 25%
5 blink pause
Overtemperature: zone may be
overloaded, all loads turned off
800 W Max 500 W Max 500 W Max 500 W Max
S1
S2
S3
S4
CCI
Zone 1 Zone 2 Zone 3 Zone 4
Type
IR
Photo Occ Switch
Hi Temp
Prog
Power
230 V~ 50 / 60 Hz 10 A
Option
Def
H
Opt1
M
Opt2
L
Normal operation
Rapid flash: 10 blinks/sec
Emergency mode/Contact open/Jumper
missing
“Input”
Continuous On
Viewing wired input
Flashing: 1 blink/sec
Viewing remote input on a QS Sensor
Module (QSM)
Off
Sensor never detected or not currently
receiving information
Sensor is detected and is currently
receiving information
“Def, Opt 1-3”
(Default, Option 1-3)
Off
Flashing/On
Device in normal mode
Selected option for programming mode
Troubleshooting using symptoms:
Symptom
Cause
Solution
Unable to add daylight
sensor to a zone
Not allowed to assign
16th occupancy sensor
to a zone
Daylight sensor fails to
turn on a zone
Existing daylight sensor
already assigned to the zone
Existing occupancy sensor
still assigned to the zone
Unassign the existing daylight sensor and
try again
Unassign the existing occupancy sensor
and try again
Daylight sensors will not turn a zone on
if an occupancy sensor assigned to that
zone detects that the room is vacant
Switched zone daylighting:
Reset the daylighting set point.
Daylighting Setup
incorrect light level set during See
Daylighting Setup
When associating a
A QSM has already been
To clear the QSM association and any
QSM to the ESN, the
associated to the ESN
ESN zone assignments to any QSM inputs,
“Input” LED on the ESN
press and hold the “Input” button on the
flutters for 1 second,
ESN for 10 seconds. The “Input” LED will
then turns off
flutter for 1 second, then turn off
When associating a
Maximum number of
Unassign any unnecessary wireless inputs
wireless input device
associations to the QSM has of that device type and try again
to a QSM, the QSM
been exceeded for that
responds with 10 short wireless input device type
beeps
When associating a
Input device is already
If you choose to ignore the warning and try
wireless input device
associated to another QSM to associate the same input device to the
to a QSM, the QSM
on the QS link
QSM a second time, the input device will be
responds with 5 short
removed from association with the previous
beeps
QSM and will now be associated with the
new QSM. Note: This will also remove any
ESN programming that the wireless device
may have had through the previous QSM
Subsection: Assign Zones to PicoR
Wireless Controller (through QSM)
Occupancy sensor is
overriding the zone
Wired
seeTouchR QS
Wallstation
Input
Input
Multiple errors: contact Lutron
Continuous On
Continuous On/Flashing
If you have other devices wired to the ESN QS Link terminal block, see below to determine which additional
sections to read.
QS Link
Energi
Savr
NodeT
Unit
(ESN)
Rapid flash:10 blinks/sec
“CCI”
(Contact Closure Input)
“Input S1-S4”
OTHER QS LINK DEVICES
Additional Sections:
Opt3
www.lutron.com +44.(0)20.7702.0657
»
LUTRON
Wired seeTouchR QS Wallstations Setup
GRAFIK EyeR QS
Control
Unit
BUTTON AND LED LOCATIONS
Additional Sections:
»
CCO 1
CCO 2
CCO 3
CCO 4
CCO 5
8 7 6 5 4 3 2 1
QSE-IO
24 V
100 mA
800.523.9466
+1.610.282.3800
243C IND. CONT. EQ.
www.lutron.com/qs
0
2 7 5 5 7 6 1 32 3
V
0-24 V
0-24 V
GRAFIK EyeR QS Control Unit Setup
QSE-IO
Input/Output
Interface
800 W Max 500 W Max 500 W Max 500 W Max
Input
S1
S2
S3
S4
CCI
Zone 1 Zone 2 Zone 3 Zone 4
Type
IR
Photo Occ Switch
Input
Hi Temp
Prog
Power
230 V~ 50 / 60 Hz 10 A
Option
Def
H
Opt1
M
Opt2
L
Opt3
www.lutron.com +44.(0)20.7702.0657
Inputs
1
Additional Sections:
R
R
1A
½A
V
5 COM
CCO 5 NO
CCO 5 NC
Zones
COM
CCI 5
CCI 4
CCI 3
CCI 2
CCI 1
4 3 2 1
CCO 4 NO
CCO 4 NC
3-4 COM
CCO 3 NO
CCO 3 NC
QS
MUX
Daylighting Setup
Occupancy Setup
Subsection: Assign Zones to
QSM Inputs
»
Subsection: Assign Zones
to QSM Inputs
MUX
»
»
»
»
COM
V+
ESN Wired Input Setup
Daylighting Setup
Additional Sections:
CCO 2 NO
CCO 2 NC
1-2 COM
CCO 1 NO
CCO 1 NC
»
ESN Wired Input Setup
»
Additional Sections:
®
»
Subsection: Assign Zones to
QSM Inputs
Pico®
Wireless
Controller
STAT
Additional Sections:
Occupancy Setup
Infrared (IR)
Sensor
Wires to multi-function Input
Additional Sections:
Flashing: 1 blink/sec
Additional Sections:
Wired
Occupancy
Sensor
Wired
Daylight
Sensor
Unit is too hot, loads turned off
QS Sensor Module (QSM)
Input Setup
QS Sensor Module (QSM)
Zone Assignment
Wireless
Daylight
Sensor
500-13491 Rev. B
N OR
TUL
+44.(0)20.7702.0657
+44.(0)20.7702.0657
www.lutron.com
230 V~ 50
230
/ 60
V~
Hz50
10/ 60
A Hz 10 A www.lutron.com
Unit is too hot, loads scaled to 25% power
Continuous On
Additional Sections:
Occupancy Setup
N
O
R
Power Power
H
Opt1
QSNE-4A-D
Input
Hi TempHi Temp
Option Option
Def
Def
DIN Rail Power Module
Input
QSNE-4A-D
Type
DIN Rail Power Module
Type
Normal Operation
1 second on, 7 seconds off
Wireless
Occupancy
Sensor
»
QSNE-4A-D
S3
Off
Subsection: Associating Wireless Input
Devices to a QSM
»
DIN Rail Power Module
S2
N OR
TUL
»
QSE-IO Input/Output Interface Setup
800 W Max 500 W Max 500 W Max 500 W Max
Input
S1
S2
S3
S4
CCI
Zone 1 Zone 2 Zone 3 Zone 4
Type
www.lutron.com
Lutron, GRAFIK Eye, Pico, seeTouch and ) are registered trademarks, and Energi Savr Node and Radio Powr Savr are
trademarks of Lutron Electronics Co., Inc.
Apple, iPhone, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. AppStore is a service
mark of Apple Inc.
© 2013 Lutron Electronics Co., Inc.
P/N 032416 Rev. A 08/2013
®
Button
LED
Photo Occ Switch
Input
Hi Temp
Prog
Power
QSNE-4A-D
IR
DIN Rail Power Module
»
S1
Type
R
Read:
800 W Max 500 W Max 500 W Max 500 W Max
Input
Read:
»
CONFIGURATION WHEN USING WIRED INPUTS
All Wired Inputs
General system failure/No power; verifiy
breaker is on
Opt3
Additional Sections:
After Load Setup, if you have wired sensor inputs wired directly to the Energi Savr NodeT (ESN) unit
multi-function input terminal blocks, see below to determine which additional sections to read.
Off
Wires to “QS Link” Terminal Block on ESN
H
Opt1
www.lutron.com +44.(0)20.7702.0657
230 V~ 50 / 60 Hz 10 A
Opt3
www.lutron.com +44.(0)20.7702.0657
230 V~ 50 / 60 Hz 10 A
Zone 1 Zone 2 Zone 3 Zone 4
Subsection: Associating Wired
Input Devices to a QSM
LUTRON
S3
CCI
Additional Sections:
800 W Max 500 W Max 500 W Max 500 W Max
S2
S4
Wired
Occupancy
Sensor
Input
IR
S3
Read:
Energi Savr NodeT with Phase Adaptive Control
(QSNE-4A-D)
S1
S2
Photo Occ Switch
Read:
Load Setup
Input
IR
Communicates with QSM via Radio Frequency (RF)
Read:
»
800 W Max 500 W Max 500 W Max 500 W Max
S1
Type
Wires to Input Terminal Blocks on QSM
All Energi Savr NodeT (ESN) units
Normal operation
Input
QSM Wireless Input Devices
LOAD SETUP
Description
Continuous On
QS Sensor Module (QSM)
QSM Wired Input Devices
»
LED Behavior
“Power”
“Hi Temp”
(High Temperature)
QS Link
USING THIS GUIDE
LED
QSNE-4A-D
+44.(0)20.7702.0657
+44.(0)20.7480.6899
www.lutron.com/europe
QSNE-4A-D
Lutron EA LTD
Energi Savr NodeT with Phase Adaptive Control
LED Diagnostic Indicators
After Load Setup, if you have a QSM wired to the ESN QS Link terminal block, read sections
QS Sensor
QS Sensor Module (QSM) Zone Assignment. Some parts of the section
Module (QSM) Input Setup and
may not apply, depending on the devices connected to the QSM. See below to determine which additional subsections to read for each type of connected device.
DIN Rail Power Module
English
manual programming guide
TROUBLESHOOTING
CONFIGURATION WHEN USING QS SENSOR MODULE (QSM)
DIN Rail Power Module
Energi Savr NodeTM
230 V~ 50 / 60 Hz 10 A
Lutron Electronics Co., Inc. | 7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
Technical Assistance | 1.800.523.9466 USA, Canada, and the Caribbean | +44.(0)20.7702. 0657 Europe | +65.6220.4666 Asia | +.610.282.3800 Others | www.lutron.com
Option
Def
H
Opt1
M
Opt2
L
Opt3
www.lutron.com +44.(0)20.7702.0657
Page 1 of 4
Figure C QS Sensor Module (QSM) Input Setup
LEDs and BUTTON PRESSES
LED states:
Off
On
a. Occupancy Sensor (“Occ”): Assign zone(s). Press and hold the “Zone” button of any zone for 3 seconds to assign the zone
Associating Wireless Input Devices to a QSM
See visual instructions on left.
See written instructions at right.
Blink/Flash
Energi Savr NodeTM (ESN) Wired Input Setup - continued
1.
Enter QSM Wireless Input Setup
2.
QSM
3.
Associate Devices
“Occ”
“Photo”
(Occupancy Sensor)
QSM
Pico®
(Daylight Sensor)
to the selected input. A flashing “Zone” LED indicates an assigned zone.
Exit Setup
the selected input. A flashing “Zone” LED indicates an assigned zone.
Note: Each zone can only be assigned to a single daylight sensor input. The zone must be unassigned from the input before assigning
to a different daylight sensor input.
800 W Max 500 W Max 500 W Max 500 W Max
Inputs
Input
S1
S2
S3
S4
CCI
Zone 1 Zone 2 Zone 3 Zone 4
Type
Prog
Power
QSNE-4A-D
Photo Occ Switch
DIN Rail Power Module
IR
Hi Temp
Option
Def
H
Opt1
M
Opt2
L
To unassign a zone, press and hold the “Zone” button of the desired zone for 3 seconds. The “Zone” LED will turn off to indicate an
unassigned zone.
Zones
Repeat steps 7 and 8 for each desired input.
Opt3
www.lutron.com +44.(0)20.7702.0657
230 V~ 50 / 60 Hz 10 A
800 W Max 500 W Max 500 W Max 500 W Max
S1
S2
S3
S4
CCI
Press and hold
6 seconds
Press and hold
3 seconds
Input
Zone 1 Zone 2 Zone 3 Zone 4
Press and hold
6 seconds
Press and hold
6 seconds
Press and hold
3 seconds
Type
LED
Prog
Power
H
Opt1
M
Opt2
L
1.
Enter QSM / ESN Association
2.
Opt3
Input
Hi Temp
Prog
Figure A Load Setup
2.
Enter Zone Setup
Power
3.
Select Zone (if applicable)
Zone 1 Zone 2 Zone 3 Zone 4
Input
Hi Temp
Press
4.
Change Setting
Option
Def
800 W Max 500 W Max 500 W Max 500 W Max
Prog
Select Option
M
Opt2
L
Press and hold
3 seconds
S2
S3
S4
CCI
Power
Input
Opt1
Hi Temp
Opt2
Prog
Opt3
Power
Press and hold
3 seconds
6.
Input
Opt1
Hi Temp
Opt2
Prog
Opt3
Power
S2
S3
S4
CCI
7.
S2
S3
S4
CCI
Power
S1
Zone 1 Zone 2
Input
Opt1
Hi Temp
Opt2
Prog
Opt3
Power
Press and hold
3 seconds
IR
QSNE-4A-D
Prog
CCI
Zone 1 Zone 2
option. When setting the Daylight Gain, high/low end trim, or the minimum light level option, the “H-M-L” LEDs will flutter when the
limit has been reached.
Option
Def
Photo Occ Switch
Input
Opt1
Hi Temp
Opt2
Prog
Opt3
Power
Option
Def
LED
Option
Def
Occupancy /
Vacancy
Opt1
Opt2
Opt3
S2
S3
S4
CCI
Function
Occupancy (default)
M
Vacancy
for more light
for less light
Opt 1
Daylight Gain
H-M-L
Press
Press
Opt 2 1
Load Type2
H-M-L
H
M
L
Unassigned/Non-dim (default)3
Auto (dim) (phase detection)
MLV (dim) (leading edge / forward phase)
ELV (dim) (trailing edge / reverse phase)
H-M
100% maximum (default) down to 55%
minimum
Zone 1 Zone 2
Option
Def
Input
Opt1
Hi Temp
Opt2
Prog
Opt3
Power
Press and hold
3 seconds
Opt 3
Photo Occ Switch
Option
Def
High-End Trim
Opt1
Scene Mode
Allows IR remote to select scenes
Scene Setup for more infomation)
(see
Opt 2
Zone mode (default)
Allows setting of preset light levels for each zone
To unassign a zone, press and hold the “Zone” button of the desired zone for 3 seconds. The “Zone” LED will turn off to indicate an
unassigned zone.
Repeat steps 7 and 8 for each desired input.
Opt3
Press
Def + Opt 1
Low-End Trim
L-M
1% minimum (default) up to 45%
maximum
Def + Opt 2
Absolute
Minimum Light
Level 4
H-M-L
100% maximum down to 0% minimum
(default)
800 W Max 500 W Max 500 W Max 500 W Max
Def + Opt 3
RTISS-TE
H
Enable
L
Disable (default)
Switch Action
Maintained
Feature
Zone Toggle Preset / Off (default)
Opt 1
Momentary
Zone Toggle Preset / Off
Opt 2
Maintained (dual action)
Zones Preset / Off
Opt 3
Momentary (single action)
Zones On
Function
Contact closure or opening will toggle the state of
assigned zones between a preset and off.*
Contact closure will toggle the state of assigned
zones between a preset and off.*
Contact closure will set assigned zones to preset
level. Contact open will set assigned zones off.
Contact closure will set assigned zones to preset
level. Contact open will set assigned zones off.
* If one or more assigned zones are on at the time of contact closure or opening, all assigned zones will turn off.
Set zone level. Select zone by pressing the “Zone” button for the zone you wish to set up, then use the
the zone’s preset light level.
1
2
Note: Selecting the wrong
dimming type may result in poor
dimming performance and may
damage the load and/or the
Energi Savr NodeT unit. Consult
fixture manufacturer if unsure of
proper dimming type.
To determine the load type
during normal operation, press
the “Option” button. The “Zone”
LEDs will blink:
Solid On = trailing edge/reverse
phase
1 blink / sec = leading edge/
forward phase
3
Zone 1 Zone 2 Zone 3 Zone 4
4
Each zone is unassigned by
default and will switch load
on or off until it is configured.
Once configured, the load type
cannot be changed back to
Unassigned/Non-Dim.
This setting is required in certain
cities. Check local electrical
codes to verify requirements.
Repeat steps 2 and 3 for each desired zone.
Press and hold
3 seconds
LED
Def
Save the selected option. Press and hold the “Option” button for 3 seconds. The LED for the selected option will remain
steady ON.
Opt2
Setup Options
Assign Zones
a.
b.
Setting Choices
H
Press
800 W Max 500 W Max
Photo Occ Switch
DIN Rail Power Module
Hi Temp
QSNE-4A-D
DIN Rail Power Module
Input
S4
Type
IR
Option
Def
S3
Input
S1
Photo Occ Switch
S2
Select Input
Type
IR
IR
800 W Max 500 W Max
Zone 1 Zone 2
S1
Zone 1 Zone 2
Press
Input
Type
8.
Option
Def
Exit Change Sensor Type Mode
800 W Max 500 W Max
Input
S1
CCI
Photo Occ Switch
Press and hold
3 seconds
Assign Sensor Type
S4
2. Select Zone. Press a “Zone” button to select a zone. When a zone is selected, the zone's LED will blink once per second.
3. Select Option. Press the “Option” button to select an option. Use the and buttons for each zone to select the choice for each
Type
IR
QSNE-4A-D
Prog
Option
Def
Photo Occ Switch
DIN Rail Power Module
Hi Temp
QSNE-4A-D
Input
S3
Type
IR
Photo Occ Switch
DIN Rail Power Module
IR
800 W Max 500 W Max
Input
S2
Opt 1
Switch—IEC PELV/NECR Class 2 dry contact switch
“Def” (Default), “IR” (Infrared), and “Photo” (Daylight) LEDs will blink once per second.
800 W Max 500 W Max
S1
Zone 1 Zone 2
Type
Type
Press and hold
3 seconds
Load Setup
Select Sensor Type
Input
S1
Zone 1 Zone 2
QSNE-4A-D
CCI
DIN Rail Power Module
S4
QSNE-4A-D
S3
DIN Rail Power Module
S2
4.
Select Input
Input
S1
5.
3.
800 W Max 500 W Max
800 W Max 500 W Max
Input
Press and hold
3 seconds
1. Enter Zone Setup Mode. Simultaneously press and hold the “Prog” (Program) and “Input” buttons for 3 seconds. The “Prog,”
QSNE-4A-D
Enter Change Sensor Type Mode
Opt3
PROGRAMMING
Press and hold
3 seconds
DIN Rail Power Module
2.
Function
d. Dry Contact (Switch): The LED for the currently saved option will be steady ON. Press the “Option” button to select the desired
option. The LED for the selected option will flash.
Figure B Energi Savr NodeTM (ESN) Wired Input Setup and Zone Assignment
Enter Program Mode
Option
Save the selected option. Press and hold the “Option” button for 3 seconds. The LED for the saved option will remain steady ON.
Set zone level (Zone Mode only). Select zone by pressing the “Zone” button for the zone you wish to set up, then use
and
buttons to adjust the zone’s preset light level.
the
Opt2
Power
Press
1.
Opt1
Hi Temp
Press
LED
Option
Def
Prog
Press and hold
3 seconds
button to select the desired option. The LED for the selected option will flash.
Assign zone(s). Press and hold the “Zone” button of the zone for 3 seconds to assign the zone to the selected input. A flashing
“Zone” LED indicates an assigned zone.
Input
Opt3
Power
Exit QSM / ESN Association
Exit Zone Setup
H
Opt1
3.
Associate QSM
www.lutron.com +44.(0)20.7702.0657
230 V~ 50 / 60 Hz 10 A
c. Infrared (“IR”) Sensor or Wired Wallstation: The LED for the currently saved option will be steady ON. Press the “Option”
QSM Association to an ESN
QSNE-4A-D
Hi Temp
Option
Def
DIN Rail Power Module
Input
QSNE-4A-D
Button
Photo Occ Switch
DIN Rail Power Module
IR
1.
Repeat steps 7 and 8 for each desired input.
b. Daylight Sensor (“Photo”): Assign zone(s). Press and hold the “Zone” button of any zone for 3 seconds to assign the zone to
Button and LED Locations
Input
To unassign a zone, press and hold the “Zone” button of the desired zone for 3 seconds. The “Zone” LED will turn off to indicate an
unassigned zone.
4. Exit Zone Setup Mode. Simultaneously press and hold the “Prog” and “Input” buttons for 3 seconds to exit.
and
buttons to adjust
Assign zone(s). Press and hold the “Zone” button of the zone for 3 seconds to save the zone level and assign the zone to the
selected input. A flashing “Zone” LED indicates an assigned zone.
To unassign a zone, press and hold the “Zone” button of the desired zone for 3 seconds. The “Zone” LED will turn off to indicate an
unassigned zone.
Repeat steps 7 and 8 for each desired input.
e. Emergency Input (“CCI”): The default emergency levels are 100% for all zones. Zones cannot be unassigned from emergency
CCI input.
Set zone level. Select zone by pressing the “Zone” button for the zone you wish to set up, then use the
the zone’s emergency light level.
and
buttons to adjust
Repeat steps 7 and 8 for each desired input.
9. Exit Program Mode. Press and hold the “Prog” (Program) button for 3 seconds to exit.
QS Sensor Module (QSM) Input Setup
Associating Wired Input Devices to a QSM
Once wired inputs are connected to the QSM, upon power up, the QSM will automatically detect and configure the wired inputs after
a valid signal is received. For example: occupied room, “IR” signal, etc.
If any wired inputs are moved to a different connection on the QSM, the inputs will need to be re-detected. To force the QSM to
re-detect all wired inputs, press and hold the “Prog” (Program) button for 10 seconds.
Associating Wireless Input Devices to a QSM
Wireless input devices must be associated to only one QSM before they are assigned to control system devices.
1. Enter Input Setup. Press and hold the “Prog” button on the QSM for 3 seconds. You will hear a 1-second beep upon entering, and
c.
d.
Select Option
the Status LED will blink.
Save Selected Option
Option
Def
Option
Def
Opt1
Opt1
Opt2
Opt2
Opt3
Opt3
Press
Input
Device
Button
Press For
Device Feedback
Maximum Per
QSM
Radio Powr SavrT
Occupancy Sensor
g/
Lights Off
6 seconds
LED flashes briefly
10
will blink once per second. The Sensor “Input” LED will blink once per second to display the selected input, and the Sensor “Type”
LED will be steady ON to display the inputs current type.
Radio Powr SavrT
Daylight Sensor
Link
6 seconds
LED flashes briefly
10
LEDs of sensors wired to the ESN will flash to help with identification.
PicoR Wireless
Controller
Off Button
6 seconds
None
10
1. Enter Program Mode. Press and hold the “Prog” (Program) button for 3 seconds. The “Prog” LED will blink once per second. The
“Type” LED(s) will be steady ON showing the input type. One of the Sensor “Input” LEDs will be blinking to show the selected input. If
all “Type” LEDs are steady ON, the selected input has not been assigned a sensor type.
2. Enter Change Sensor Type mode. Press and hold the “Input” and “Option” button for 3 seconds. The “Prog” and “Input” LEDs
800 W Max 500 W Max
Input
9.
Assign Zones*
S2
H
Zone 1 Zone 2 Zone 3 Zone 4
M
Zone 1 Zone 2 Zone 3 Zone 4
IR
Hi Temp
Power
Press and hold
3 seconds
Press
CCI
Zone 1 Zone 2
3. Select Input. Press the “Prog” button to select an input. When an input is selected, the input’s LED will blink once per second. Also,
4. Select Sensor Type. Press the “Input” button to select a sensor type. When a sensor type is selected, the sensor’s “Type” LED will
blink once per second.
Photo Occ Switch
Input
Prog
L
Press
S4
Type Program Mode
Exit
800 W Max 500 W Max 500 W Max 500 W Max
800 W Max 500 W Max 500 W Max 500 W Max
S3
QSNE-4A-D
Set Zone Level
S1
DIN Rail Power Module
c.
d.
e.
to the following table:
Energi Savr NodeTM (ESN) Wired Input Setup
Press and hold
3 seconds
Set Zone Level
Select Zone
2. Associate devices. For each wireless device you wish to associate, press and hold the appropriate button on the device according
Option
Def
Opt1
Opt2
Opt3
Press and hold
3 seconds
5. Assign Sensor Type. Press and hold the “Input” button for 3 seconds fo assign the sensor type.
After each successful input association, QSM will respond with 3 long beeps (2 seconds each).
Note: If QSM responds in any other way, consult the Troubleshooting section on the first page of this guide.
3. Exit Input Setup. Press and hold the “Prog” button on the QSM for 3 seconds to exit.
Repeat steps 3 - 5 to assign a sensor type for each desired sensor input.
6. Exit change Sensor Type mode. Press and hold the “Input” and “Option” button for 3 seconds to exit and return to Program
Mode.
QSM Association to an ESN
7. Select input. Press the “Prog” button to select an input. Corresponding LED will blink. Also, LEDs of sensors wired to the ESN will
1. Press and hold the “Prog” button on the QSM for 3 seconds. You will hear a 1-second beep upon entering, and the Status LED will
8. Setup options. Follow the appropriate section for each sensor type.
2. Associate QSM. On the ESN to which the QSM will be associated, press and hold the “Input” button for 3 seconds until the “Input”
flash to help with identification.
*Not applicable for step e
blink. The “Input” (Input) LEDs on ESN(s) on the QS link will sequence through each sensor type, and the “Opt 3” (Option 3) LED will
be steady ON.
LED on the ESN unit begins to flash.
3. Exit QSM Association. Press and hold the “Prog” button on the QSM for 3 seconds to exit.
Continued next column...
®
Lutron Electronics Co., Inc. | 7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
Technical Assistance | 1.800.523.9466 USA, Canada, and the Caribbean | +44.(0)20.7702. 0657 Europe | +65.6220.4666 Asia | +.610.282.3800 Others | www.lutron.com
Page 2 of 4
Figure D QS Sensor Module (QSM) Zone Assignment
Figure G QSE-IO Input / Output Interface Setup
Scene Selection Control or Sequencing Control
Assigning Zones to QSM Inputs (Occupancy, Daylight, IR)
2.
Enter Program Mode
3.
Select QSM
Select Wired Input. Selected Input Blinks
800 W Max 500 W Max
800 W Max 500 W Max
S2
S3
S4
CCI
S2
S3
S4
CCI
S1
Zone 1 Zone 2
Type
Prog
Power
Photo Occ Switch
Input
Opt1
Hi Temp
Opt2
Prog
Opt3
Power
IR
QSNE-4A-D
Hi Temp
QSNE-4A-D
Input
Option
Def
S2
S3
S4
CCI
Option
Def
Opt1
Hi Temp
Opt2
Prog
Opt3
Power
Option
Def
Opt1
Opt3
Press and hold
3 seconds
Zone Toggle Control
Enter Zone Toggle Setup
2.
3.
Select Input
Selected Input Blinks
S1
Set Zone Level
Assign Zones
S2
S3
S4
CCI
Zone 1 Zone 2
Press and hold
6 seconds
Hi Temp
Press and hold
6 seconds
Prog
Power
800 W Max 500 W Max
Input
S2
S3
S4
CCI
QSNE-4A-D
Input
Opt1
4.
Hi Temp
Prog
Power
5.
Assign Zones
800 W Max 500 W Max 500 W Max 500 W Max
Opt3
Zone 1 Zone 2 Zone 3 Zone 4
Press
Exit Zone Toggle Setup
Press and hold
3 seconds
Option
Def
Opt1
Opt2
1.
Opt3
Partition Control
Enter Partition/Sequencing
Control Setup
2.
3.
Select Input
Assign Zones
4.
Exit Partition/Sequencing
Control Setup
Zone 1 Zone 2 Zone 3 Zone 4
800 W Max 500 W Max
Controllers (through
QSM)
Assigning Zones to Pico® Wireless
Input
Input
Prog
Power
QSNE-4A-D
DIN Rail Power Module
Hi Temp
Option
Def
Input
S4 S1CCI S2
S3
Type
Photo Occ Switch
IR
Option
Def
(IR receiver: Zone Mode Only)
Input
Input
Opt1
Hi Temp
Hi Temp
Opt1
Opt2
Prog
Prog
Opt2
Opt3
Power
Power
Opt3
Option
Def
Press
H
Opt1
M
Opt2
L
Press and hold
3 seconds
“Type” LED(s) will be steady ON showing the input type.
Press
2. Select QSM. Press the “Input” button on the ESN to select QSM. The “Input” will blink once per second and the “Def” (Default) LED
will be steady ON.
3. Select wired input: Each input from an associated QSM will be indicated by a steady ON “Type” LED as listed below:
4.
Assign Zone
Exit PicoR Wireless Controller Assignment
800 W Max 500 W Max 500 W Max 500 W Max
Zone 1 Zone 2 Zone 3 Zone 4
LED
Input Type
Occ
Photo
IR
Indicates an associated occupancy sensor (wired and wireless) from a QSM.
Indicates an associated daylight sensor (wired and wireless) from a QSM.
Indicates an associated IR receiver (wired only) from a QSM.
Wireless Daylight sensor: Press and hold the “Link” button for 6 seconds, until the sensor’s dome begins to flash. The ESN will
automatically select that input.
S3
IR
2.
S4
Photo Occ Switch
IR
DIN Rail Power Module
1 button wallstation: Dual column wallstations:
Press and hold
Press and hold
top and bottom
Input
single button
button of each column
Hi Temp
Prog
Power
S2
Zone 1 Zone 2
Select
Option
Type
Option
Def
S3
S4
CCI
Zone 1 Zone 2
Save
Option
Photo Occ Switch
Input
Opt1 Hi Temp
Opt2 Prog
Opt3 Power
QSNE-4A-D
S2
Type
4. Assign zones. Press and hold the “Zone” button of any zone for 3 seconds to assign the zone to the selected input. A flashing
800 W Max 500 W Max
DIN Rail Power Module
S1
Enter Wallstation Setup
QSNE-4A-D
1.
Input
800 W Max 500 W Max
Input
CCI
S1
Select Button
(Zone Toggle Only)
Option
Def
“Zone” LED indicates an assigned zone.
5. Exit Program Mode. Press and hold the “Prog” button for 3 seconds to exit.
1. Enter PicoR wireless controller Assignment. Simultaneously press and hold the top and bottom buttons on the PicoR wireless
Opt2
controller for 3 seconds. The QSM will beep for 1 second and the “Status” LED on the QSM will flash 3 times per second. The “Input”
LED on the ESN(s) will flash once per second and the sensor “Type” LEDs will scroll through each input type. All unassigned zones will
turn off.
Opt3
2. Setup options. Press the “Option” button to select the desired option. The LED for the selected option will flash.
Press and hold
3 seconds
Press
Note: Gray buttons signify buttons to be pressed.
Press and hold
3 seconds
Press
LED
Def
800 W Max 500 W Max 500 W Max 500 W Max
Option
Scene + Off mode
LED
Option
Opt 2
Zone Mode
(Only available with
QSM 5.X or below)
Opt 3
Single action zone
mode (default)
Input
S1
S2
S3
S4
CCI
Zone 1 Zone 2 Zone 3 Zone 4
DIN Rail Power Module
IR Photo Occ Switch
800 W Max 500 W Max 500 W Max 500 W Max
Input
(Zone Mode Only)
Option
Def
Power
QSNE-4A-D
Prog
Opt1
M
Opt2
L
4.
Assign Zone
Exit Wallstation Setup
800 W Max 500 W Max 500 W Max 500 W Max
H
Zone 1 Zone 2 Zone 3 Zone 4
Hi Temp
3.
Set Zone Level
Type
Select
Zone
Press
Scene mode
and
Zone Mode: Set zone levels. Use the
the default light level of 100% will be saved.
Press
Press and hold
3 seconds
Press and hold
3 seconds
1.
2.
Enter GRAFIK EyeR QS Setup
Assign Zones
3.
Exit GRAFIK EyeR QS Setup
800 W Max 500 W Max 500 W Max 500 W Max
Zone 1 Zone 2 Zone 3 Zone 4
LUTRON
Press and hold
3 seconds
Press and hold
3 seconds
Press and hold
3 seconds
A QSE-IO configured as a Sequencing Control can be used to start and stop automatic sequencing of scenes 5-16.
1. Enter Sequencing Control Setup. Press and hold the “Prog” button on the QSE-IO for 3 seconds. The 5 output LEDs on the
QSE-IO will cycle. The sensor “Type” LEDs on the ESN(s) will scroll sequentially through each
input type.
2. Assign zones. Press and hold the desired “Zone” button on the ESN unit for 3 seconds to assign the zone to “Input 1” on the
QSE-IO. A flashing “Zone” LED indicates an assigned zone.
To un-assign zones from the QSE-IO, press and hold the desired “Zone” button on the ESN for 3 seconds. The “Zone” LED will turn
off to indicate the zone is unassigned.
Zone Toggle Control
A QSE-IO configured as a Zone Toggle Control can be used to toggle zones on your ESN using contact closure inputs into the
QSE-IO, or to monitor the state (on or off) of the zones on your ESN using contact closure outputs out of the QSE-IO.
To associate a QSE-IO that is set in a Zone Toggle configuration to an ESN(s):
1. Enter Zone Toggle Setup. Press and hold the “Prog” button on the QSE-IO for 3 seconds. The first output LED will flash indicating
“Input 1” is selected. The sensor “Type” LEDs on the ESN(s) will scroll sequentially through each input type.
A flashing “Zone” LED indicates an assigned zone.
To un-assign zones from the QSE-IO, press and hold the desired “Zone” button on the ESN for 3 seconds. The “Zone” LED will turn
off to indicate the zone is unassigned.
buttons to adjust zone preset light levels. Note: If a zone is left off and is assigned,
Scene Mode: Scene assignments are factory set. The top button is Scene 1, the bottom button is the Off Scene, and the Favorite
button (if present) is Scene 2. Refer to
Scene Setup to adjust zone levels for each scene.
3. Assign zones. Press and hold the “Zone” button of the desired zone for 3 seconds. A blinking “Zone” LED indicates an assigned
Repeat steps 2-4 for each desired zone and QSE-IO input.
5. Exit Zone Toggle Setup. Press and hold the “Prog” button on the QSE-IO for 3 seconds to exit.
Partition Control
A QSE-IO configured as a Partition Control can be used to select scenes on your ESN using contact closure inputs into the QSE-IO,
based on the status of movable walls.
To associate a QSE-IO that is set in a Partition Control configuration to an ESN(s):
1. Enter Partition Control Setup. Press and hold the “Prog” button on the QSE-IO for 3 seconds. The first output LED will flash
indicating “Input 1” is selected. The sensor “Type” LEDs on the ESN(s) will scroll sequentially through each input type.
Repeat steps 2 and 3 for each desired zone-to-PicoR wireless controller assignment.
4. Exit PicoR wireless controller Assignment. Simultaneously press and hold the top and bottom buttons on the PicoR wireless
controller for 3 seconds to exit.
2. Select input. Press the “Prog” button on the QSE-IO to select an input. Corresponding LED will blink.
3. Assign zones. Press and hold the desired “Zone” button on the ESN for 3 seconds to assign the zone to “Input 1” on the QSE-IO.
A flashing “Zone” LED indicates an assigned zone.
To un-assign zones from the QSE-IO, press and hold the desired “Zone” button on the ESN for 3 seconds. The “Zone” LED will turn
off to indicate the zone is unassigned.
Wired seeTouchR QS Wallstation Setup
1. Enter Wallstation Setup. Simultaneously press and hold the top and bottom buttons (excluding raise/lower) on the wallstation for
LUTRON
Sequencing Control
4. Assign zones. Press and hold the desired “Zone” button on the ESN for 3 seconds to assign the zone to “Input 1” on the QSE-IO.
zone. A ”Zone” LED that is off indicates an unassigned zone.
Figure F GRAFIK EyeR QS Control Unit / GRAFIK EyeR QS Timeclock Setup
2. Assign zones. Press and hold the desired “Zone” button on the ESN for 3 seconds to assign the zone to the QSE-IO. A flashing
desired light level for the desired zone.
Save the selected option. Press and hold the “Option” button for 3 seconds. The LED for the selected option will remain
steady ON.
Opt3
“Type” LEDs on the ESN(s) will scroll sequentially through each input type.
2. Select input. Press the “Prog” button on the QSE-IO to select an input. Corresponding LED will blink.
3. Set light levels. First press the “Zone” button for the zone you wish to setup, then use the and buttons on the ESN to set the
Zone 1 Zone 2 Zone 3 Zone 4
www.lutron.com +44.(0)20.7702.0657
230 V~ 50 / 60 Hz 10 A
Opt 1
To associate a QSE-IO that is set in a Scene configuration to an ESN(s):
1. Press and hold the “Prog” (Program) button on the QSE-IO for 3 seconds. The 5 output LEDs on the QSE-IO will cycle. The sensor
3. Exit Sequencing Control Setup. Press and hold the “Prog” button on the QSE-IO for 3 seconds to exit.
Assigning Zones to PicoR Wireless Controllers (via QSM)
Opt1
A QSE-IO configured as a Scene Selection Control can be used to change scenes on your ESN using contact closure inputs
on the QSE-IO, or to monitor scene changes on your ESN using contact closure outputs on the QSE-IO.
To associate a QSE-IO that is set in a Sequencing Control configuration to an ESN(s):
Wireless Occupancy sensor: Press and hold the “Lights Off” or g button for 6 seconds, until the sensor’s dome begins to flash.
The ESN will automatically select that input.
Figure E Wired seeTouchR QS Wallstation Setup
QSE-IO Input/Output Interface Setup
3. Exit Scene Selection Setup. Press and hold the “Prog” button on the QSE-IO for 3 seconds.
Select wireless input:
Press and hold
3 seconds
QS Setup. Simultaneously press and hold the top and bottom buttons on the GRAFIK Eye® QS unit for 3
“Zone” LED indicates an assigned zone.
To un-assign zones from the QSE-IO, press and hold the desired “Zone” button on the ESN for 3 seconds. The “Zone” LED will
turn off to indicate the zone is unassigned.
Press the “Prog” button to sequence through each associated input. The LED corresponding to the selected input will blink (other
associated input LEDs will remain steady ON).
Press and hold
3 seconds
®
Scene Selection Control
1. Enter Program Mode. Press and hold the “Prog” (Program) button for 3 seconds. The “Prog” LED will blink once per second. The
Press and hold
3 seconds
indicates an assigned zone.
To un-assign ESN zones from a GRAFIK Eye® QS unit, press and hold the desired “Zone” button on the ESN for 3 seconds. The
“Zone” LED will turn off to indicate the zone is unassigned.
The ESN can be associated to a QSE-IO that is configured as a scene selection control, sequencing control, zone toggle control,
or a partition control. Refer to instrucitons below.
Note: QSM must be assigned to ESN before assigning zones. See Section C.
Opt3
2. Assign zones. Press and hold the desired “Zone” button on the ESN for 3 seconds to assign the zone. A flashing “Zone” LED
Refer to the Installation Instructions provided with the QSE-IO for proper DIP switch settings.
QS Sensor Module (QSM) Zone Assignment
Assigning Zones to QSM Inputs (Occupancy, Daylight, IR)
www.lutron.com +44.(0)20.7702.0657
230 V~ 50 / 60 Hz 10 A
Press and hold
3 seconds
Press and hold
3 seconds
Set Zone Level
Photo Occ Switch
(Refer to Application Note 048447 for GRAFIK EyeR QS Remote Zone Mapping.)
® QS Setup. Simultaneously press and hold the top and bottom scene buttons on the GRAFIK Eye® QS unit for
3 seconds. The sensor “Type” LEDs on the ESN will scroll sequentially through each input type.
seconds to exit.
S3
CCI
Zone
1 S4Zone
2Zone 1 Zone 2 Zone 3 Zone 4
Save Option
QSNE-4A-D
IR
Photo Occ Switch
Input
S2
DIN Rail Power Module
S1
Zone 1 Zone 2
Select Option
Type
QSNE-4A-D
CCI
DIN Rail Power Module
2.
S4
buttons
4. Exit Wallstation Setup. Simultaneously press and hold the top and bottom buttons on the wallstation for 3 seconds to exit.
3. Exit GRAFIK Eye
Press and hold
3 seconds
800 W Max 500 W Max800 W Max 500 W Max 500 W Max 500 W Max
and
1. Enter GRAFIK Eye
Press
3.
Special Mode (Partitioning, Sequencing)*
Refer to the Installation Instructions provided with the GRAFIK Eye® QS control unit or
GRAFIK Eye® QS timeclock to set up time events.
Press and hold
3 seconds
Press and hold
3 seconds
Press and hold
3 seconds
IR
Opt 3
GRAFIK Eye® QS Control Unit / GRAFIK Eye® QS Timeclock Setup
800 W Max 500 W Max 500 W Max 500 W Max
S3
Scene
“Zone” LED indicates an assigned zone.
Zone 1 Zone 2
QSNE-4A-D
DIN Rail Power Module
Input
S2
Opt 1
To un-assign ESN zones from a specific wallstation, press and hold the “Zone” button of the desired zone for 3 seconds. The “Zone”
LED will turn off to indicate the zone is unassigned.
Opt2
Type
S1
Zone Toggle
3. Assign zones. Press and hold the “Zone” button of the desired zone for 3 seconds to assign the zone to the wallstation. A blinking
L
Option
Def
Exit Program
Mode
IR Photo Occ Switch
800 W Max 500 W Max 500 W Max 500 W Max
Enter PicoR Wireless Controller Assignment
Type
Opt 2
Set zone levels (Zone Toggle only): First press the “Zone” button for the zone you wish to set up, then use the
to adjust zone preset light levels.
M
Press and hold
3 seconds
Press
Press and hold
3 seconds
Photo Occ Switch
DIN Rail Power Module
IR
1.
Scene + off
Assign zones to buttons (Zone Toggle only): To assign a specific ESN zone to a wallstation button, press the wallstation button
you wish to assign. The button LED will blink slowly.
H
Zone 1 Zone 2 Zone 3 Zone 4
Type
Zone 1 Zone 2 Zone 3 Zone 4
Def
Save option: Press and hold the “Option” button for 3 seconds to save the wallstation type. The LED for the selected wallstation
type will flutter for 1 second, then remain steady ON.
800 W Max 500 W Max 500 W Max 500 W Max
800 W Max 500 W Max
5.
Option
* Wallstation must already be set up as a Partitioning or Sequencing Control. If any other Wallstation Type is selected for an existing
Special Mode wallstation, the wallstation is reprogrammed to the selected type, and cannot be re-selected as a Special Mode
wallstation.
Press and hold
3 seconds
Press and hold
3 seconds
Input
Assign Zones
LED
Opt2
1.
4.
Option
Zone 1 Zone 2 Zone 3 Zone 4
Press
Select Wireless: Select Daylight Sensor
S1
LED
Exit Scene Selection Setup
Photo Occ Switch
Input
Press
Press and hold
3 seconds
Select Wireless: Select Occupancy Sensor
3.
Assign Zones
800 W Max 500 W Max 500 W Max 500 W Max
Zone 1 Zone 2
Type
IR
Photo Occ Switch
DIN Rail Power Module
IR
DIN Rail Power Module
Type
2.
Enter Scene Selection Setup
Input
S1
Zone 1 Zone 2
QSNE-4A-D
S1
1.
800 W Max 500 W Max
Input
Input
DIN Rail Power Module
1.
Wired seeTouchR QS Wallstation Setup - continued
3 seconds. The Sensor “Type” LEDs on the ESN(s) will scroll sequentially through each input type.
Repeat steps 2 and 3 for each desired zone and QSE-IO input.
4. Exit Partition Control Setup. Press and hold the “Prog” button on the QSE-IO for 3 seconds to exit.
Note: On wallstations with dual columns, each column is set up separately.
2. Select option. Press the “Option” button on the ESN to select the scene wallstation type. LED for currently saved type will remain
steady ON.
Continued next column...
®
Lutron Electronics Co., Inc. | 7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
Technical Assistance | 1.800.523.9466 USA, Canada, and the Caribbean | +44.(0)20.7702. 0657 Europe | +65.6220.4666 Asia | +.610.282.3800 Others | www.lutron.com
Page 3 of 4
Figure H Occupancy Setup
Occupancy Setup
800 W Max 500 W Max
Input
S1
Enter Zone Setup
S2
2.
S3
S4
Type
IR
DIN Rail Power Module
Input
S1
S2
S3
S4
CCI
ZoneHi
1 Temp
Zone 2
Type
Prog
Photo Occ Switch
Input
Hi Temp
Prog
Power
Option
Power
Def
QSNE-4A-D
DIN Rail Power Module
IR
3.
Zone 1 Zone 2
Select Option
4.
Select Zone
Select Response Mode
Photo Occ Switch
800 W Max 500 W Max
Input
CCI
QSNE-4A-D
1.
800 W Max 500 W Max 500 W Max 500 W Max
Option
Def
2. Select “Def” (Default): Use the “Option” button to select “Def.”
3. Select Zone: Press the “Zone” button to select the zone you w)ant to change.
4. Select response. Use the and buttons to select the response type for each desired zone:
M
Opt2
L
Opt3
Opt1
Opt2
Press
Press
Opt3
Press
Press and hold
3 seconds
800 W Max 500 W Max
Input
S2
S3
S4
CCI
Exit Zone Setup
Input
Hi Temp
Prog
Power
Zone Response Type
H
Occupancy mode (auto on/off)
M
Vacancy mode (manual on/auto off)
Opt1
Select Scene for Occupied State
Opt2
Note: All zones use the same “Occupied Scene” and cannot be set on a zone-by-zone basis. All zones use the Off Scene for the
unoccupied/vacant state.
Opt3
800 W Max 500 W Max
2.
Type
IR
CCI
S2
S3
S4
CCI
Input
Zone 1 Zone 2
Hi Temp
Photo Occ Switch
Input
Hi Temp
Prog
Power
Power
S1
S2
S3
S4
CCI
Opt2
Zone 1 Zone 2
Prog
Power
QSNE-4A-D
DIN Rail Power Module
Hi Temp
CCI
Zone 1 Zone 2
Input
Hi Temp
Opt2
Prog
Opt3
Power
S2
View Scenes
5-16
Type
Photo Occ Switch
Opt1
S1
IR
Option
Def
S3
S4
CCI
Select Scene
(Scenes 5-16)
Photo Occ Switch
Input
Opt1
Hi Temp
Opt2
Prog
Opt3
Power
Option
Def
Opt1
4.
2. Select Scene. Press the “Option” button to select a scene:
S1
S2
IR
Opt2
S3
S4
CCI
Prog
Power
S3
CCI
2.
Type
Input
CCI
ZoneHi
1 Temp
Zone 2
Type
Prog
Input
Hi Temp
Prog
Power
QSNE-4A-D
Photo Occ Switch
DIN Rail Power Module
IR
Opt2
S4
CCI
75%
3
50%
3
50%
4
25%
4
25%
Scene
#
800 W Max 500 W Max
Option
Power
Def
LED
Pattern
5
Zone 1 Zone 2
3. Select Zone
Press and hold the “Option” button for 10 seconds, then use the “Option” button to select a scene.
= flashing
Scene
#
= off
4.
Default
Level
Scene
#
100%
9
LED
Pattern
Default
Level
Scene
#
100%
13
LED
Pattern
Default
Level
6
H
Zone 1 Zone 2 Zone 3 Zone 4
Opt1
Opt2
M
Opt3
L
7
100%
100%
10
11
100%
100%
14
15
Prog
Power
Default
Level
Scene
#
5
100%
6
LED
Pattern
Default
Level
Scene
#
LED
Pattern
Default
Level
9
100%
13
100%
100%
10
100%
14
100%
7
100%
11
100%
15
100%
8
100%
12
100%
16
100%
100%
Opt2
Press
Press
Press
8
100%
12
100%
16
100%
3. Set Occupied Scene. Press and hold the “Input” button for 3 seconds to set the currently selected scene as the Occupied Scene.
The “Input” LED will turn on to indicate the selection is complete.
4. Exit Scene Setup Mode. Simultaneously press and hold the “Prog” and “Option” buttons for 3 seconds to exit.
Zone 1 Zone 2
QSNE-4A-D
DIN Rail Power Module
Hi Temp
= off
100%
Photo Occ Switch
Input
LED
Pattern
= flashing
100%
Set Zone Levels
Opt1
Opt3
LED Legend:
800 W Max 500 W Max 500 W Max 500 W Max
Option
Def
Type
IR
2
LED Legend:
800 W Max 500 W Max
S3
75%
Opt3
Input
S2
100%
Press and hold the “Option” button for 10 seconds, then use the “Option” button to select a scene.
Opt1
Exit Zone Setup
S1
Default
Level
1
Scenes 5-16
Press and hold
3 seconds
5.
2
LED
Pattern
= off
Scenes 5-16
Option
Def
Select Option
Photo Occ Switch
DIN Rail Power Module
IR
S4
QSNE-4A-D
S2
800 W Max 500 W Max
S4
100%
Zone 1 Zone 2
Input
S3
1
Scene
#
= steady ON
Press
Press and hold
10 seconds
Photo Occ Switch
Input
Opt3
Daylighting Setup
S2
Default
Level
Type
S1
S1
LED Legend:
Opt3
Simultaneously Press
and hold 3 seconds
Input
LED
Pattern
= off
Input
Opt1
Enter Zone Setup
Scenes 1-4
= steady ON
800 W Max 500 W Max
Option
Def
Press and hold
3 seconds
1.
(Default) LED will be steady ON and the “Prog,” “Occ” (Occupancy Sensor), and “Switch” LEDs will blink once per second.
Opt2
Exit Scene Setup
Hi Temp
Figure I
Scene Setup
2. Select Scene. Press the “Option” button to select a scene:
Scene
#
Zone 1 Zone 2
Repeat steps 3 and 4 for each zone.
5. Exit Zone Setup Mode. Simultaneously press and hold the “Prog” and “Input” buttons for 3 seconds to exit.
500 W Max
Photo Occ Switch
Input
S4
Press
Opt3
Type Occupied Scene
Set
IR
IR
S3
Opt1
Simultaneously
Press and hold
800 W Max
3 seconds
Input
3.
Prog
Option
Def
QSNE-4A-D
DIN Rail Power Module
IR
Option
Def
DIN Rail Power Module
S1
Type
(Scenes 1-4)
DIN Rail Power Module
Input
S2
Select Scene
Type
Photo Occ Switch
800 W Max 500 W Max
Zone 1 Zone 2S1
QSNE-4A-D
S4
DIN Rail Power Module
S3
QSNE-4A-D
Enter Scene Setup
S2
QSNE-4A-D
1.
Input
S1
Zone Setup Mode. Simultaneously press and hold the “Prog” (Program) and “Input” buttons for 3 seconds. The “Prog,”
“Def” (Default), “IR” (Infrared), and “Photo” (Daylight) LEDs will blink once per second.
1. Enter Scene Setup Mode. Simultaneously press and hold the “Prog” (Program) and “Option” buttons for 3 seconds. The “Def”
Scenes 1-4
LED Legend:
800 W Max 500 W Max
QSNE-4A-D
Input
800 W Max 500 W Max
Input
DIN Rail Power Module
Select Scene for Occupied State
1. Enter
1. Enter Scene Setup Mode. Simultaneously press and hold the “Prog” and “Option” buttons for 3 seconds. The “Input” and “Def”
LEDs will be steady ON and the “Prog,” “Occ” (Occupancy Sensor), and “Switch” LEDs will blink once per second.
Press and hold
3 seconds
Set Daylight Sensor Setpoint
zones, the minimum light level) that you wish to maintain in the space.
5. Exit Zone Setup Mode. Simultaneously press and hold the “Prog” and “Input” buttons for 3 seconds to exit.
Option
Def
Daylighting setup should be performed during the daytime when there is consistent but indirect sunlight. Dark, cloudy days or days
with highly variable cloud cover that frequently changes the sunlight conditions should be avoided. Additionally, times of day when the
sunlight penetrates directly into the space should be avoided (such as morning or evening).
2. Select option. Use the “Option” button to select “Opt1” (Option 1)
3. Select Zone. Use the “Zone” button to select the zone to change.
4. Set light levels. Press the and buttons (cannot press and hold) to set the approximate light level (or, in the case of switched
Repeat steps 3 and 4 for each desired zone.
Photo Occ Switch
QSNE-4A-D
IR
Flashing LED
Zone 1 Zone 2
Type
DIN Rail Power Module
5.
S1
Set Zone Response to Occupancy Sensors
1. Enter Zone Setup Mode: Simultaneously press and hold the “Prog” (Program) and “Input” buttons for 3 seconds. The “Prog,”
“Def” (Default), “IR” (Infrared), and “Photo” (Daylight) LEDs will blink once per second.
H
Zone 1 Zone 2 Zone 3 Zone 4
Opt1
Daylighting Setup
Option
Def
3. Select Zone: Press the “Zone” button to select the desired zone to change.
4. Set light levels. Use the and buttons to adjust the light level for the zone.
To make a zone unaffected, press and hold the
To make a zone affected again, press the
on or flashing.
button until only the “M” LED is steady ON.
button until you see a combination of the “H,” “M,” and “L” LEDs steady
Repeat steps 3 and 4 for each desired zone.
5. Exit Scene Setup Mode. Simultaneously press and hold the “Prog” and “Option” buttons for 3 seconds to exit.
Opt1
Opt2
Opt3
Note: The fade time between scenes is factory set to 3 seconds, and is not adjustable.
Press and hold
3 seconds
800 W Max 500 W Max
IR
Input
S1
S2
S3
S4
CCI
Type
Hi Temp
Prog
Power
QSNE-4A-D
Input
Option
Def
CCI
2.
Photo Occ Switch
Input
Zone 1 Zone 2
Hi Temp
Photo Occ Switch
DIN Rail Power Module
IR
S4
Select Scene
(Scenes 1-4)
Prog
Power
Option
Def
800 W Max 500 W Max
Input
S1
Zone 1 Zone 2
S2
S3
S4
CCI
Photo Occ Switch
Input
Opt1
Hi Temp
Opt2
Prog
Opt3
Power
S1
S2
View Scenes
Type5-16
Type
IR
Zone 1 Zone 2
IR
Option
Def
S3
S4
CCI
Zone 1 Zone 2
Select
Scene
(Scenes 5-16)
Photo Occ Switch
Input
Opt1
Hi Temp
Opt2
Prog
Opt3
Power
QSNE-4A-D
Type
800 W Max 500 W Max
S3
QSNE-4A-D
Enter Scene Setup
S2
DIN Rail Power Module
1.
800 W Max 500 W Max
Input
S1
QSNE-4A-D
Input
DIN Rail Power Module
Scene Setup
DIN Rail Power Module
Figure J
Option
Def
Opt1
Opt2
Opt3
Opt1
Opt2
Press
Press and hold
10 seconds
Opt3
Press
Simultaneously Press
and hold 3 seconds
800 W Max 500 W Max 500 W Max 500 W Max
5.
4. Set Light Levels
Exit Scene Setup
800 W Max 500 W Max
Input
H
Zone 1 Zone 2 Zone 3 Zone 4
S1
S2
IR
L
Input
Prog
Press
®
S4
CCI
Zone 1 Zone 2
Photo Occ Switch
Hi Temp
Press
S3
Type
M
Power
QSNE-4A-D
Select Zone
DIN Rail Power Module
3.
Option
Def
Simultaneously
Press and hold
3 seconds
Opt1
Opt2
Opt3
Lutron Electronics Co., Inc. | 7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
CONTACT INFORMATION
World headquarters
European headquarters
Asian headquarters
Technical hotlines
United States
United Kingdom
Singapore
France: 0800.90.12.18
Lutron Electronics Co., Inc.
Lutron EA Ltd.
Lutron GL Ltd.
Germany: 00800.5887.6635
7200 Suter Road
6 Sovereign Close
15 Hoe Chiang Road,
Italy: 800.979.208
Coopersburg, PA 18036-1299 USA
London, E1W 3JF UK
#07-03 Tower Fifteen,
Spain: 900.948.944
TEL +1.610.282.3800
TEL +44.(0)20.7702.0657
Singapore 089316
Northern China: 10.800.712.1536
FAX +1.610.282.1243
FAX +44.(0)20.7480.6899
TEL +65.6220.4666
Southern China: 10.800.120.1536
Technical Support 1.800.523.9466
Technical support
FAX +65.6220.4333
Hong Kong: 800.901.849
+44.(0)20.7680.4481
Singapore: 800.120.4491
FREEPHONE 0800.282.107
Taiwan: 00.801.137.737
Thailand: 001.800.120.665853
Other Areas in Asia: +65.6220.4666
Technical Assistance | 1.800.523.9466 USA, Canada, and the Caribbean | +44.(0)20.7702. 0657 Europe | +65.6220.4666 Asia | +.610.282.3800 Others | www.lutron.com
Page 4 of 4