3832CDO
QUICK REFERENCE
Applications: For use on
keyboard shelves, pull-out work
surfaces or box drawers. Not intended
for lateral file** drawer applications.
Use for side mount only. This
product is covered by U.S.
(5,980,007) and various foreign
patents issued and/or pending.
MODEL 3832CDO
Detent In and Out
Vertical Drawer Adjustment Cam
Optional Face Frame Brackets
Side space: 1/2" + 1/16'' x 2
Length: 10"–28"
Overall slide dimensions: 1.80" x 1/2"
Minimum drawer height: 1-7/8"
Load Rating: 100 lbs.*
INCHES
[mm]
Closed Position
Drawer Member Flush or Under
Slide Travel
1.26
[32.0]
3832-C22-DO Only
18.90
[480.0]
H
G
F
E
D
C
1.38
[35.1]
B
A
5.04 ¤
[128.0]
.50 [12.7]
2.38
[60.5]
1.38
[35.1]
5.04
[128.0]
.45
Intermediate [11.4]
Member
TYP.
Latch
.35 [9]
Disconnect /Detent
Lever
.50
[12.7]
TYP.
.50
[12.7]
1.80
[45.7]
*
.187 x .310
[4.7 x 7.9]
TYP.
.172 DIA.
¤ Dimension is 3.78 [96.0] for 3832-C10, C12-DO
[4.4] TYP.
* Not available on 10" or 12"
.70 [17.8]
.35 [9]
.42 [10.6]
Finishes
Clear electroplate (C), black,
electroplate (CB), or white
electrocoat (EW) finish
Lengths
10"–28" [199 mm–700 mm]
Side Space
.172 x .38
[4.4 x 9.5]
TYP.
.44 [11.2]
.50" +0.031 / -0.0
[12.7 mm +.8 / -0.0]
1.35
[34.3]
.85
[21.6]
.180 DIA.
[4.6] TYP.
.180 x .375 .250 DIA.
[4.6 x 9.5] [6.4] TYP.
TYP.
.75 [19.1]
Slide Length
Slide
Length
Slide
Travel
3832-C10-DO
9.84
[250]
9.59
[243]
7.56
[192]
3832-C12-DO
11.81
[300]
12.00
[305]
9.52
[242]
8.82
[224]
3832-C14-DO
13.78
[350]
14.00
[356]
11.50
[292]
8.82
[224]
13.47
[342]
8.82
[224]
Part Number
A
B
C
D
E
F
G
Travel
Full extension
Height
1.80" [45.7 mm]
3832-C16-DO
15.75
[400]
16.00
[406]
100 lbs. [45.5 kg.] per pair*
3832-C18-DO
17.72
[450]
18.00
[457]
12.60
[320]
15.43
[392]
13.86
[352]
3832-C20-DO
19.69
[500]
20.00
[508]
12.60
[320]
17.40
[442]
16.38
[416]
3832-C22-DO
21.65
[550]
22.00
[559]
12.60
[320]
19.37
[492]
13.86
[352]
3832-C24-DO
23.62
[600]
24.00
[610]
8.82
[224]
16.38
[416]
3832-C26-DO
25.59
[650]
26.00
[660]
8.82
[224]
16.38
[416]
3832-C28-DO
27.56
[700]
28.00
[711]
8.82
[224]
16.38
[416]
Load
Disconnect
Front, handed lever
Mounting
Side or optional face frame brackets
Hardware
Flat head 6 mm Euro System screw
or #8 pan head screw
Ball Bearings
Features
*
C & CB finish: Steel
EW finish: Acetal polymer in drawer member
Detent open and closed; drawer
member has vertical adjustment cam;
silenced open and closed.
Load rating based on an 18" slide mounted in a 16" wide drawer cycled 50,000 times.
** A lateral file drawer is wider than it is deep.
11.34
[288]
16.38
[416]
H
12.60
[320]
21.34
[542]
8.82
[224]
13.86
[352]
18.90
[480]
21.42
[544]
23.31
[592]
8.82
[224]
13.86
[352]
21.42
[544]
21.42
[544]
25.28
[642]
8.82
[224]
21.42
[544]
Installation Instructions
2
1. Drawer Box Preparation
4. Drawer Insertion and Adjustment
Drawer box width should not exceed slide length.
Make sure the ball bearing retainers in the cabinet member are fully forward. Insert the drawer member into the cabinet member. Push the drawer in until completely closed. Cycle the drawer two or three times.
Slides will not function properly if side space is less than
.50" [12.7 mm]. For optimum performance, construct drawer
1-1/16" [27.0 mm] smaller than cabinet opening.
2. Cabinet Member Installation
Overlay drawer front:
• Conventional mounting, see Figure 1.
• 32 mm system mounting, see Figure 2.
Inset drawer front: slide setback is the thickness of the
drawer front plus 1/8" [3.2 mm].
Conventional Mounting—Cabinet
Figure 1
Horizontal Slots
Drawer
1-1/2"
For overlay
drawer front
2-3/8"
Cabinet Member
32 mm System—Cabinet
Figure 2
2.0 mm
37.0 mm
Cabinet Member
Drawer
To adjust the drawer front position, open the drawer and rotate the
cam with a Phillips or Pozi screwdriver to adjust the vertical
position of the drawer. Total vertical adjustment is 1/8" [3.2 mm]; +/- 1/16" [1.6 mm] from center up and down.
Install additional set screws to secure. Install drawer pulls or knobs.
Optional Face Frame Brackets
Face frame brackets are ordered as a kit or in bulk. Brackets
are available in clear zinc finish only. Mounting screws are not
included.
To order kits, specify part number
4180-0322-XE. Each kit
contains:2 front brackets,
2 rear brackets, and
installation instructions.
Order 1 kit per pair
of slides. Optional front clip-on
bracket part number
4010-0516-CE
For bulk,
order 2 front brackets
(P/N 4010-0516-CE)
and 2 rear brackets
(P/N 4080-0508-CE)
per pair of slides.
Optional
rear metal face
frame bracket
part number
4080-0508-CE
Slide Ordering Information
38.1 mm
System Holes
For overlay
drawer front
Complete your slide order for Accuride models 3832-DO by
specifying the following:
Use only the 32 mm system holes or the wood screw holes located at the tip of the breathing tabs. Do not use any other holes on the cabinet member for mounting (Figure 3).
Figure 3
Yes
50 Pair C 3832
-C18 DO D
Total Required Slides
Slide Finish
Slide Model
Slide Length
Detent Out Feature
Polybag Packaging
Packaging
Distributor (D) Pack: All lengths are packaged 10 pair per box.
Polybag includes one pair of slides with mounting screws.
No
Use all mounting tabs to achieve load rating
Bulk (P) Pack: All lengths are packaged 10 pair per box. Slides
and screws are ordered and packaged separately.
3. Drawer Member Installation
Available in clear zinc (C), black (CB), and white (EW) finishes.
See Figure 4 for drawer member setback.
Specifications
Install the drawer member with a screw through the cam adjuster and a screw through a hole or slot at the rear (Figure 5).
Figure 4
Conventional and 32 mm Mounting—Drawer
11/16" [17.8]
1/8" for Conventional Mounting
[5.2] for 32 mm System Mounting
Figure 5
Accuride part number
2410-3218-CE
Cam Adjuster
RoHS compliant.
NOTE: Specifications, materials, prices, terms, and
delivery are subject to change without notice.
Conventional Vertical Slots
32mm System Vertical Slot
Slide members and ball retainers: Cold rolled steel
Ball bearings: Carburized steel/acetal polymer
1-1/4"
[31.8]
1/4" [6.4]
NOTE: Cam must be installed on
same centerline as drawer
1/16" [1.6 mm] maximum
member. The cam is designed for
head height
use with the standard Accuride
truss head screw. If using other
screw, ensure screw head height
does not exceed 1/16" [1.6mm]
since it may cause interference.
For the most current technical information visit www.accuride.com
ACCURIDE INTERNATIONAL INC.
12311 Shoemaker Avenue
Santa Fe Springs, CA 90670
TEL (562) 903-0200
FAX (562) 903-0208
www.accuride.com
Manufacturing, Engineering, and Sales
United States • Germany • Japan • Mexico • United Kingdom • China
Copyright © 2007 Accuride International Inc. 3700-9465(1110)-MK078-R7-1013