Ruger® Mini-14® Strikeforce Six Position Adjustable
Side Folding TactLite Stock w/Scorpion Recoil System
B.2.10.1210 B.2.20.1210 B.2.40.1210
70.0879.01
1
Side Folding Stock
2
Removable/Adjustable Tactical Cheekrest
3
Dual Sided QD Mount
4
Six Position Adjustable
5
Scorpion Recoil Pistol Grip
6
7" Picatinny Top Rail
7
2" Picatinny Rail
1
6
2
7
3
4
5
Ruger® Mini-14® Strikeforce Six Position Adjustable Side
Folding TactLite Stock with Scorpion Recoil System
[2] 6-32 x 1/2" Machine Screw
[6] 6-32 x 3/8" Machiine Screw
[4] 6-32 x 5/16" Phillips Head
Screw
[2] 6-19 x 3/8 Plastite Phillips
Head Screw
[5] 10-32 x 7/16 Sling Swivel
[1]
[1]
[1]
[4]
8-32 x 5/16 Male Barrel Bolt
8-32 Barrel Bolt Female
6-32 x .75 Flat Head Screw
6-32 x .25 Low Profile Screw
Phillips Head Screwdriver
[15] 6-32 Hex Nut
[3] 10-32 Hex Nut
Warning: When handling a firearm, always follow the proper handling procedures at all times.
!
Stainless Steel Insert Installation
A
!
Failure to follow
these procedures could result in serious damage, injury, or death. ATI is not responsible for damage to property,
injury, or death resulting from improper installation, misuse or modification of products. If you are not
comfortable completing any of the following steps, or do not have the proper tools enlist the help of your
local gunsmith. ATI is not responsible for components that are damaged due to improper installation.
Point the rifle in a safe direction and place the saftey in
the "on" position. Next remove the magazine, pull
back, and carefully inspect the chamber to be sure the
rifle is unloaded.
NOTE: Before the installation of the Mini-14 Stock to the
firearm begins, determine whether or not installation of
the Picatinny Rails is desired. If desired, begin
installation of all Picatinny Rails on page 2 before you
begin installation. If it is not, you may begin installation of
the stock to the firearm.
1
2
If you do not desire to install picatinny rails, begin by
sliding the Stainless Steel Insert into the front of the stock
body with the larger end facing forward as seen in Figure
1A. Make sure that the pilot holes in the Steel Insert and
in the Stock Body are lined up correctly as seen in Figure
1B.
Note: If you desire to install picatinny rails, begin
installation on page 2.
1A
1B
Using a Phillips Head Screwdriver, secure the Steel
Insert into place with two of the #6 x 48/2 x 3/8" Flat Head
Plastite Screws provided as seen in Figure 2. Do not
over tighten the screws during installation or the screw
may strip.
2
70.0879.01
1
Ruger® Mini-14® Strikeforce Six Position Adjustable Side
Folding TactLite Stock with Scorpion Recoil System
Picatinny Rail Installation
B
1
If you choose to install the 2" bottom rail, locate the
bottom picatinny rail with the swivel stud attachment as
seen in Figure 1A. Thread the swivel stud into the
picatinny rail using (1) 10-32 hex nut. Then locate the
pockets at the bottom of the stock for hex nut placement
as seen in Figure 1B. Insert (2) 6-32 hex nuts into the
pockets and hold in place.
1A
1B
2
Align the bottom picatinny rail into place as seen in Figure
2A. Holding a finger over the hex nut, use a phillips head
screwdriver to fasten the (2) 6-32 x 3/8" Machine screws
and bottom picatinny rail into place as seen in Figure 2B.
2A
2B
70.0879.01
2
Ruger® Mini-14® Strikeforce Six Position Adjustable Side
Folding TactLite Stock with Scorpion Recoil System
Picatinny Rail Installation -Continued
B
3
Locate the existing pocket on the inside of the stock for
hex nut placement as seen in Figure 3A. Insert (2) 6-32
hex nuts into pocket, and hold firmly in place as seen in
Figure 3B.
3A
3B
4
Align one of the side picatinny rails to the stock in
designated slot as seen in Figure 4.
4
70.0879.01
3
Ruger® Mini-14® Strikeforce Six Position Adjustable Side
Folding TactLite Stock with Scorpion Recoil System
Picatinny Rail Installation -Continued
B
5
Holding a finger over the hex nut, use a phillips head
screwdriver to fasten the (2) 6-32 x 3/8" Machine screws
to the picatinny rail as seen in Figure 5. Turn the gun
over, and repeat for the opposite side picatinny rail
attachment.
5
6
Locate the top picatinny rail and the Ruger mini top cover.
Insert the rail into existing slots on the top of Ruger mini
top cover as seen in Figure 6.
6
7
Insert (4) 6-32 hex nuts into the existing pockets on the
reverse side of the top cover. Holding the hex nut in
place with your finger, use a philips head screwdriver to
fasten the (4) 6-32 x 5/16" screws in place and secure the
top rail to the top cover as seen in Figure 7.
7
C
1
Stock Installation
Locate the stainless steel insert and refer back to step A1
to fit the insert back into the stock. Once in place, use a
phillips head screwdriver and the (2) provided 6 x 48/2 x
3/8 plastite phillips head screws to secure the insert to the
stock.
Note: The raised edge of the stainless steel insert goes
towards the front of the stock as seen in Figure 1.
70.0879.01
1
4
Ruger® Mini-14® Strikeforce Six Position Adjustable Side
Folding TactLite Stock with Scorpion Recoil System
Stock Installation -Continued
C
2
Locate the barreled action. Align the barrel to the front of
the stock. Bring the rear of the barrel down towards the
rear of the stock as seen in Figure 2A, and firmly secure
the barrel into place as seen in Figure 2B.
2A
2B
3
Locate the Ruger mini top cover plate with new top
picatinny rail attached. Align the cover from the front, and
bring the cover down into place as seen in Figure 3.
3
4
Align the trigger assembly and insert back into place.
Lock the trigger assembly by firmly pushing the trigger
guard up and into the locked position as seen in Figure 4.
4
NOTE: After installing the trigger assembly make sure to
function check your Mini 14 to insure that the bolt is
cycling properly. If your bolt sticks during any portion of
the cycle you may have to add a 3/32 x 5/8" shim
between the trigger assembly and stock as seen in
Figure .
70.0879.01
5
Ruger® Mini-14® Strikeforce Six Position Adjustable Side
Folding TactLite Stock with Scorpion Recoil System
C
5
Stock Installation -Continued
Using the provided (1) 6-32 x 1/2" Machine screw and a
phillips head screwdriver, tighten the cover plate in place
as seen in Figure 5.
5
D
1
Buffer Tube Installation
To install the Buffer Tube and Buttstock you will need to
make sure stock is in the folded position. Begin by
pressing together on the pin cap and under the pivot
housing as seen in Figure 1.
1
2
Install the buffer tube into the knuckle of as seen in Figure
2.
2
6
Ruger® Mini-14® Strikeforce Six Position Adjustable Side
Folding TactLite Stock with Scorpion Recoil System
Buffer Tube Installation -Continued
D
3
Using the provided 14 x 3/4 Phillps Head Screw and a
Phillips Head screwdriver, tighten the buffer tube to the
knuckle as seen in Figure 3.
3
Cheekrest Installation
E
1
Begin by removing the cheekrest from the Tactlite Stock
by pulling up on the cheekrest as seen in Figure 1.
1
2
Next, remove the cheekrest rail from the Tactlite body as
seen in Figure 2. Repeat the same process for the
opposite side.
2
70.0879.01
7
Ruger® Mini-14® Strikeforce Six Position Adjustable Side
Folding TactLite Stock with Scorpion Recoil System
Cheekrest Installation -Continued
E
3
Place the (5) 6/32 nuts into the slots of the cheekrest rail
as seen in Figure 3.
NOTE: Make sure that the nuts inside the rail do not fall
out while installing the rail onto the buttstock.
3
4
Attach the left cheekrest rail as seen in Figure 4A onto the
left side of the Tactlite Stock Body by snapping in place
as seen in Figure 4B. Repeat the same process on the
right side of the buttstock.
4A
4B
70.0879.01
8
Ruger® Mini-14® Strikeforce Six Position Adjustable Side
Folding TactLite Stock with Scorpion Recoil System
Cheekrest Installation -Continued
E
5
Using the provided 6-32 x .75 Flat Head Screw and a
5/64” allen wrench (not provided), tighten the left side
cheekrest rail to the right side cheekrest rail by threading
the screw threw the left side as seen in Figure 5.
5
6
Next choose the cheekrest you would like installed (short
or tall) and then take the cheekrest as seen in Figure 6
and slide onto the cheekrest rails making sure the holes
on the cheekrest line up with the cheekrest rail holes.
6
7
Using the provided 6-32 x .25 Low Profile Allen Head
Screws and a 1/16 allen wrench (not provided), attach the
cheekrest to the cheekrest rails as seen in Figure 7.
Repeat the same process for the opposite side of the
cheekrest.
7
70.0879.01
9
Ruger® Mini-14® Strikeforce Six Position Adjustable Side
Folding TactLite Stock with Scorpion Recoil System
Drop Tube Adapter Installation
F
NOTE: The Drop Tube Adapter can be used on several
ATI stocks to provide the consumer with the ability to
utilize the Iron Sights on some models, and also to help
reduce the recoil affect.
1
With the stock folded, use a phillips head screw driver to
unscrew the buffertube from the pivot housing assembly
as seen in Figure 1
NOTE: For the aluminum upgrade you will need to use a
5/32" allen wrench to unscrew the buffer tube from the
pivot housing.
1
2
Pull the buffer tube out of the pivot housing assembly as
seen in Figure 2.
2
3
Next insert the adapter into the pivot end. Make sure that
the adapter is angled down as seen in Figure 3. If you
have purchased ATI's Tactical Shotgun Stock place the
large washer into the pivot housing assembly before
inserting the adapter.
3
70.0879.01
10
Ruger® Mini-14® Strikeforce Six Position Adjustable Side
Folding TactLite Stock with Scorpion Recoil System
Drop Tube Adapter Installation -Continued
F
4
Using the screw that you removed in step 2, connect the
adapter to the pivot housing assembly with a phillips head
screwdriver as seen in Figure 4.
4
5
With the stock in the non-folded position, attach the buffer
tube into the adapter. Make sure that the tube is at a
downward angle as seen in Figure 5.
5
6
Line up the holes in the buffer tube with the holes in the
drop tube adapter. Push the 8-32 x 5/16 barrel bolt
though the adapter as seen in Figure 6A and secure it by
connecting the barrel bolt with the 8-32 mating screw as
seen in Figure 6B.
70.0879.01
6A
6B
11