INSTALLATION INSTRUCTIONS
E-DD1 SERIES and E-DD0 SERIES
Document: CI308X02R3
Date: 02-14-2011
Created by: AJB
DCR#: 11-025
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions
should always be followed including the following:
READ AND FOLLOW ALL
SAFETY INSTRUCTIONS
1. To avoid the possibility of electrical shock, turn
off power supply before installation or servicing.
2. Use only lamp specified for this fixture.
3. In continuously operating Metal Halide systems
(24 hours/day, 7 days/week), turn lamps off once
per week for at least 15 minutes. Failure to
comply increases the risk of violent lamp failure.
4. Properly attach reflector to ballast housing
module before applying voltage.
SAVE THESE INSTRUCTIONS
NOTE:
When installing the housing on to the arm, allow 1/4"
(6.4 mm) spacing between end of arm and the housing
to prevent ground wire from being pinched.
ARM MOUNTING
1. Loosely install (2) carriage bolts with lock washers
and nuts into wall mount bracket.
2. Install wall mounting bracket to mounting surface
with (4) Lag bolts and washers provided.
3. Insert short end of arm into mounting bracket. Adjust
to desired direction and tighten carriage bolts.
4. Feed (Customer Supplied) Ground wire up through
arm.
5. Feed ballast wires down through arm.
6. Using (2) Hex bolts and arm bracket, secure housing
to arm.
NOTE: When installing the housing on to the
arm, allow 1/4" (6.4 mm) spacing between end of
arm and the housing to prevent ground wire
from being pinched.
7. Install (1) green ground screw and lock-washer on
arm bracket at location marked “GND” and tighten
ground screw to ground wire.
8. Fasten reflector to fixture housing using (2) machine
screws and washers.
9. Wire black fixture lead to the incoming hot lead and
the white fixture lead to the incoming neutral
(Common) lead.
10. Install the Photo-control by aligning the arrow on the
top of the photo-control with the arrow on the photocontrol socket and inserting pins into the socket.
Twist photo-control clockwise until it locks in place
(approximately 1/8 turn).
(NOTE: Improper installation of the photo-control
may result in damage to the photo-control.)
11. Install lamp.
___________________________________________________________________________________________________________
www.e-conolight.com
| 888.243.9445 | FAX: 262.504.5409
INSTALLATION INSTRUCTIONS
E-DD1 SERIES and E-DD0 SERIES
Document: CI308X02R3
Date: 02-14-2011
Created by: AJB
DCR#: 11-025
9. Install the Photo-control by aligning the arrow on the
top of the photo-control with the arrow on the photocontrol socket and inserting pins into the socket.
Twist photo-control clockwise until it locks in place
(approximately 1/8 turn).
(NOTE: Improper installation of the photo-control
may result in damage to the photo-control.)
DIRECT MOUNTING
10. Install lamp.
1. Install fixture cover plate to conduit using either
knockout.
2. Screw green ground screw and lock-washer into
fixture arm.
3. Use fixture to mark the location for the lag bolts on
mounting surface.
4. Install two lower lag bolts into mounting surface,
allowing the head of each bolt to remain 1/4" (6.4
mm) from mounting surface.
5. Wire black fixture lead to the incoming hot lead and
the white fixture lead to the incoming neutral
(Common) lead. Attach ground lead to green ground
screw.
6. Slide fixture onto two lag bolts from #5 and install
third lag bolt in top slot of fixture. Secure all lag
bolts.
7. Secure cover plate with (2) machine screws,
washers and nuts.
8. Install reflector using (2) machine screws and
washers.
___________________________________________________________________________________________________________
www.e-conolight.com
| 888.243.9445 | FAX: 262.504.5409