01_140M_Circuit_Breakers_A.qxd
4/22/2008
4:14 PM
Page 2-2
Bulletin 140M
Motor Protection Circuit Breakers
Product Overview
!
1
Bulletin 140M Motor Protection Circuit Breakers
Table of Contents
y Current Range 0.1…630 A
y UL Listed for Motor Loads
− Short Circuit Protection
− Overload Protection
y Visible Trip Indication
y High Current Limiting
y High Switching Capacity
Product Selection —
Motor Protection
Circuit Breakers.......... 2-8
Approximate
Dimensions................... 2-49
2
The Bulletin 140M Motor Protection Circuit Breakers provide short
circuit and overload protection for individual motor loads. Factoryinstalled internal accessories make installation and wiring easy.
3
Your order must include: cat. no. of the Motor Protection Circuit
Breaker selected and, if required, cat. no. of any accessories.
Standards Compliance
IEC/EN 60947-1, -2, -4-1, -5-1
IEC/EN 60204-1
CSA, C22.2 No.14
UL 508
UL 489
Certifications
4
CE Marked
cULus Listed (File No.
E197878, E205542, Guide
DIVQ/DIVQ7, NKJH/NKJH7)
CCC
CSA Certified
General Information
Motor Protection Circuit Breakers may provide the following protective and control functions.
5
y Disconnect for Motor Branch Circuit
y Branch-Circuit, Short-Circuit Protection (Magnetic Protection)
y Overload Protection (Thermal Protection)
y Switching (Manual)
6
In North America, electrical codes require that an individual Motor Branch Circuit be protected by a UL/CSA Listed Fuse, Circuit Breaker or
Self-Protected Combination Motor Controller.
140M-C, D and F Frames:
7
8
The 140M-C, D and F frame Motor Protection Circuit Breakers may have 2 cULus Listings – as Manual, Self-Protected Combination Motor
Controllers and as Manual Motor Controllers (with optional approvals for Motor Disconnect and Group Installation).
When UL/CSA listed as Manual, Self-Protected Combination Motor Controllers, the 140M Motor Protection Circuit Breakers provide all of the
necessary NEC/CEC requirements for the protection and control of individual Motor Branch Circuits without additional protective devices.
At some higher voltages and currents (particularly at 600V), a few of the 140M-C, D and F frame devices are only UL/CSA Listed as Manual
Motor Controllers (with optional approvals for Motor Disconnect and Group Installation). In NEC/CEC Group Installations, these devices must
be applied per the appropriate rules which require the use of an upstream Branch-Circuit, Short-Circuit Protective Device (BCPD). See the
table on page 2-17 for the specific ratings of each Motor Protection Circuit Breaker.
140-CMN Frame:
9
The 140-CMN frame Motor Protection Circuit Breakers are UL Listed/CSA Certified as Manual Motor Controllers (with optional approvals for
Motor Disconnect and Group Installation). In NEC/CEC Group Installations, these devices must be applied per the appropriate rules which
require the use of an upstream Branch-Circuit, Short-Circuit Protective Device (BCPD). See the table on page 2-17 for the specific ratings of
each Motor Protection Circuit Breaker.
140M-I, J and L Frames:
10
The 140M-I, J and L frame Motor Protection Circuit Breakers are cULus Listed as Circuit Breakers as shown in the table on page 2-9. In
these cases, the 140M Motor Protection Circuit Breakers provide all of the necessary NEC/CEC requirements for the protection and control of
individual Motor Branch Circuits without additional protective devices.
For further details on the proper application of Motor Protection Circuit Breakers, please see the diagrams on the following pages.
11
12
13
Visit our website: www.ab.com/catalogs
2-2
Preferred availability cat. nos. are printed in bold
01_140M_Circuit_Breakers_A.qxd
4/22/2008
4:15 PM
Page 2-3
Bulletin 140M
Motor Protection Circuit Breakers
Product Overview, Continued
!
1
C-Frame
D-Frame
F-Frame
CMN-Frame
I-Frame
J-Frame
Max. Current Ie
25 A
25 A
45 A
90 A
205 A
250 A
L-Frame
630 A
Current Rating
0.1…25 A
1.6…25 A
6.3…45 A
16…90 A
40…205 A
20…250 A
100…630 A
Short Circuit Protection
9
9
9
9
9
9
9
Standard Magnetic Trip
9
9
9
9
9
9
9
High Magnetic Trip
9
9
9
9
—
—
—
Overload Protection
9
9
9
9
9
9
9
Trip Class
10
10
10
10
5…20
10…30
10…30
2
3
Standards Compliance:
CSA 22.2, No. 14
9
9
9
9
9
9
9
CSA 22.2, No. 5
—
—
—
—
9
9
9
UL 508 (Group Install.)
9
9
9
9
—
—
—
UL 508 Manual, Self
Protected (Type E)
9
9
9
—
—
—
—
UL 508 (Overload
Protection)
9
9
9
9
9
9
9
UL 489
—
—
—
—
9
9
9
IEC 60947-1, -2
9
9
9
9
9
9
9
IEC 60947-4-1
9
9
9
9
9
9
9
CE
9
9
9
9
9
9
9
ATEX
9
9
—
—
—
—
—
CCC
9
9
9
—
—
—
—
4
5
6
Accessories
Ext. Rotary Operator
9
9
9
9
9
9
9
Flex Cable Operator
—
—
—
—
9
9
9
Auxiliary Contacts
9
9
9
9
9
9
9
Trip Indication Contacts
9
9
9
9
9
9
9
7
8
9
10
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-3
01_140M_Circuit_Breakers_A.qxd
4/22/2008
4:15 PM
Page 2-4
Bulletin 140M
Motor Protection Circuit Breakers
Catalog Number Explanation
Cat. No. Explanation
Examples given in this section are for reference purposes. This basic explanation should not be used for product selection; not all
combinations will produce a valid catalog number.
!
140M – C – 2 – E – A63 – KN – CC – GJ
1
2
a
b
c
d
g
h
a
c
f, g, h
Interrupting Rating / Breaking Capacity
Factory-Installed Options
Description
Code
Description
140M
Motor Protection Circuit Breakers
(MPCBs)
2
Normal Break
8
High Break
f
Miscellaneous See page 2-33
b
d
g
Protection Type
Aux/Trip Contacts See page 2-33
Frame Size and Rating
5
f
Bulletin Number
Code
3
4
e
Code
Description
C
25 A
Code
Description
D
25 A
E
Adj Thermal/ Fixed Mag (13 x In)
h
F
45 A
T
UV and Shunt Trips See page 2-33
I
205 A
Adj Thermal / Fixed Mag (Fixed at 16...20
x In)
J
250 A
L
400 A and 600 A
e
Current Range
6
Code
Description
Example
A
A = .10
A16 = 0.16
B16 = 1.6
B
B = 1.0
C
C = 10
C16 = 16
D
D = 100
D16 = 160
E
E = 1000
E16 = 1600
7
8
9
10
11
12
13
Visit our website: www.ab.com/catalogs
2-4
Preferred availability cat. nos. are printed in bold
01_140M_Circuit_Breakers_A.qxd
4/22/2008
4:15 PM
Page 2-5
Bulletin 140M
Motor Protection Circuit Breakers
Product Selection
!
1
2
3
4
5
6
7
8
9
10
Group Motor Installation
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-5
01_140M_Circuit_Breakers_A.qxd
4/22/2008
4:15 PM
Page 2-6
Bulletin 140M
Motor Protection Circuit Breakers
Product Selection, Continued
3-Phase Power Supply
!
Multiple Motor Installation with MPCBs
Each Motor has an Individual Branch Circuit Protective Device
1
2
Bulletin 140M Motor Protection Circuit Breakers (MPCBs) UL/CSA Listed as Type E Manual Self-Protected Combination
Motor Controllers or UL/CSA Listed as Circuit Breakers
These UL/CSA Listings allow the Bulletin 140M MPCBs to provide the branch-circuit, short-circuit protection (as well as overload
protection) for each individual motor circuit. Additional short-circuit protection is not required for the protection of the individual
motor cuircuits, leaving only the requirement for protection of the feeder circuit conductors by an upstream protective device.
Below is an example that illustrates installations involving multiple motors, each with its own branch-circuit protection (BCPD).
3
4
Bulletin 140M-J…L
(Inverse Time Circuit Breakers)
may provide the branch-circuit
protection for each individual motor circuit
Feeder Circuit
conductors
Bulletin 140M-C…F
(Type E Self-Protected Combination Motor Controllers)
may provide the branch-circuit
protection for each individual motor circuit
5
6
7
8
9
Conductors to each
motor sized normally
at 125% FLA
10
11
Multi-Motor Installation
12
13
Visit our website: www.ab.com/catalogs
2-6
Preferred availability cat. nos. are printed in bold
01_140M_Circuit_Breakers_A.qxd
4/22/2008
4:15 PM
Page 2-7
Bulletin 140M
Motor Protection Circuit Breakers
Product Selection, Continued
Type E and Type F Combination Motor Controllers
Most of the 140M-C…F motor protection circuit breakers are UL listed as a manual Type E self-protected combination motor controller.
Although there are many tests involved, one of the critical tests a self-protected combination motor controller must pass, is to perform 6000
electrical ops. and an additional 4000 mechanical ops. after a short circuit.
!
By definition, a Type F combination motor controller consists of a Type E manual self protected combination motor controller and a magnetic
or solid-state motor controller (such as a Bulletin 100-C contactor or an SMC). As with a manual Type E self-protected combination motor
controller, additional short-circuit protection is not required for the individual motor circuits.
1
A combination of a Bulletin 140M manual self protected combination motor controller and 100-C contactor can be listed as a Type E selfprotected combination motor controller. In this case, both the 140M and 100-C must pass the additional 6000 electrical and 4000
mechanical operational test. In some cases, this may require over sizing of the Bulletin 140M MPCB or the 100-C contactor to achieve weld
free performance and meet the additional life requirements.
2
3
4
5
6
7
8
9
10
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-7
01_140M_Circuit_Breakers_A.qxd
4/22/2008
4:16 PM
Page 2-8
Bulletin 140M
Motor Protection Circuit Breakers
Product Selection, Continued
Product Selection — Motor Protection Circuit Breakers
!
y Short Circuit Protection — Standard Magnetic Trip (Fixed at 13 x Ie)
y Overload Protection — Trip Class 10
1
2
Cat. No. 140M-C
3
4
5
6
7
Cat. No. 140M-D
Ultimate
Interrupting
Motor
Magnetic
Rated
Current [kA]
Current
Trip
Operational
(Icu)
Current (Ie) Adjustment Current
400V 480V
[A]
Range [A]
[A]
Cat. No. 140M-F
Max. 3-phase Hp Ratings9
200V
230V
460V
Cat. No. 140-CMN
Max. kW, 3-Phase9
575V
230V
400/415V
500V
690V
Cat. No.
C-Frame
0.16
0.10…0.16
2.1
100
65
—
—
—
—
—
0.02
—
—
140M-C2E-A16
0.25
0.16…0.25
3.3
100
65
—
—
—
—
—
0.06
—
—
140M-C2E-A25
0.4
0.25…0.40
5.2
100
65
—
—
—
—
—
0.09
—
—
140M-C2E-A40
0.63
0.40…0.63
8.2
100
65
—
—
—
—
0.09
0.18
0.18
0.25
140M-C2E-A63
1
0.63…1.0
13
100
65
—
—
0.5
0.75
0.12
0.25
0.37
0.55
140M-C2E-B10
1.6
1.0…1.6
21
100
65
—
—
1
1
0.25
0.55
0.75
1.1
140M-C2E-B16
2.5
1.6…2.5
33
100
65
0.5
0.75
1.5
2
0.37
0.75
1.1
1.8
140M-C2E-B25
4
2.5…4.0
52
100
65
1
1
3
3
0.75
1.5
2.2
3
140M-C2E-B40
6.3
4.0…6.3
82
100
65
1.5
2
5
5
1.5
2.2
3
4
140M-C2E-B63
10
6.3…10
130
100
65
3
3
7.5
10
2.2
4
6.3
7.5
140M-C2E-C10
16
10…16
208
50
30
5
5
10
15
4
7.5
10
13
140M-C2E-C16
20
14.5…20
260
15
30
5
7.5
15
20
5.5
10
11
17
140M-C2E-C20
25
18…25
325
15
25
7.5
7.5
15
20
—
11
15
22
140M-C2E-C25
D-Frame
8
9
10
11
12
2.5
1.6…2.5
33
100
65
0.5
0.75
1.5
2
0.37
0.75
1.1
1.8
140M-D8E-B25
4
2.5…4.0
52
100
65
1
1
3
3
0.75
1.5
2.2
3
140M-D8E-B40
6.3
4.0…6.3
82
100
65
1.5
2
5
5
1.5
2.2
3
4
140M-D8E-B63
10
6.3…10
130
100
65
3
3
7.5
10
2.2
4
6.3
7.5
140M-D8E-C10
16
10…16
208
100
65
5
5
10
15
4
7.5
10
13
140M-D8E-C16
20
14.5…20
260
50
65
5
7.5
15
20
5.5
10
11
17
140M-D8E-C20
25
18…25
325
50
30
7.5
7.5
15
20
—
11
15
22
140M-D8E-C25
F-Frame
10
6.3…10
130
65
65
3
3
7.5
10
2.2
4
6.3
7.5
140M-F8E-C10
16
10…16
208
65
65
5
5
10
15
4
7.5
10
13
140M-F8E-C16
20
14.5…20
260
65
65
5
7.5
15
20
5.5
10
11
17
140M-F8E-C20
25
18…25
325
65
65
7.5
10
20
25
6.3
11
15
22
140M-F8E-C25
32
23…32
416
65
65
7.5
10
25
30
7.5
15
20
25
140M-F8E-C32
45
32…45
585
65
65
10
15
30
40
13
22
30
40
140M-F8E-C45
CMN-Frame
25
16…25
350
65
65
5
7.5
15
20
7.5
13
15
22
140-CMN-2500
40
25…40
560
65
65
10
10
30
30
11
22
25
30
140-CMN-4000
63
40…63
882
65
42
20
20
40
60
20
32
40
55
140-CMN-6300
90
63…90
1260
50
35
25
30
60
75
25
45
55
75
140-CMN-9000
9 Horsepower/kW ratings shown in the table above are for reference. The final selection of the MPCB depends on the actual motor full load current and, in
North America, service factor.
13
Visit our website: www.ab.com/catalogs
2-8
Preferred availability cat. nos. are printed in bold
01_140M_Circuit_Breakers_A.qxd
4/22/2008
4:17 PM
Page 2-9
Bulletin 140M
Motor Protection Circuit Breakers
Product Selection, Continued
Motor Protection Circuit Breakers
!
y Short Circuit Protection — Standard Magnetic Trip (Fixed at 12...15 x Ie)
y Overload Protection — Trip Class 10...30 (Adjustable)
1
Cat. No. 140M-I
Cat. No. 140M-J
Rated
Motor
Magnetic
Operational
Current
Trip
Current [A] Adjustment Current
(Ie)
Range [A]
[A]
Ultimate
Interrupting
Current [kA] (Icm)
400V
480V
3-phase Hp Ratings9
200V
230V
2
Cat. No. 140M-L
460V
3
Max. kW, 3-Phase9
575V
230V
400/415
V
500V
690V
Cat. No.
I-Frame
80
40…80
1200
707
65
25
30
60
75
22
37
55
75
140M-I8E-C807‡
100
80…100
1500
707
65
30
40
75
100
30
55
55
90
140M-I8E-D107‡
160
100…160
2400
707
65
50
60
125
150
45
75
110
132
140M-I8E-D167‡
205
160…205
2665
707
65
60
75
150
200
55
110
132
200
140M-I8E-D207§
50
20…50
700
25
25
25
30
60
75
15
22
30
45
140M-J2E-C50
100
40…100
1400
25
25
30
40
75
100
30
55
55
90
140M-J2E-D10
160
64…160
2240
25
25
50
60
125
150
45
90
110
160
140M-J2E-D16
250
100…250
3500
25
25
75
100
200
250
55
132
160
250
140M-J2E-D25
50
20…50
700
70
65
25
30
60
75
15
22
30
45
140M-J8E-C50
J-Frame
100
40…100
1400
70
65
30
40
75
100
30
55
55
90
140M-J8E-D10
160
64…160
2240
70
65
50
60
125
150
45
90
110
160
140M-J8E-D16
250
100…250
3500
70
65
75
100
200
250
55
132
160
250
140M-J8E-D25
140M-L2E-D25
4
5
6
7
L-Frame
250
100…250
3000
40
35
75
100
200
250
55
132
160
250
400
160…400
4800
40
35
125
150
300
400
132
200
250
400
140M-L2E-D40
630
250…630
7580
40
35
200
250
500
600
200
355
450
630
140M-L2E-D63
250
100…250
3000
70
65
75
100
200
250
55
132
160
250
140M-L8E-D25
400
160…400
4800
70
65
150
150
350
450
132
200
250
400
140M-L8E-D40
630
250…630
7560
70
65
200
250
500
600
200
355
450
630
140M-L8E-D63
9 Horsepower/kW ratings shown in the table above are for reference. The final selection of the MPCB depends on the actual motor full load current and, in
North America, service factor.
7 For IEC approvals and CE marking, add an "E" to the end of the Cat. No. Example: 140M-18E-C80E.
‡ Overload Protection ⎯ adjustable Trip Class 5, 10, 15, or 20.
§ Overload Protection ⎯ fixed Trip Class 10.
8
9
10
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-9
01_140M_Circuit_Breakers_A.qxd
4/22/2008
4:17 PM
Page 2-10
Bulletin 140M
Motor Protection Circuit Breakers
Product Selection, Continued
Motor Protection Circuit Breakers
!
y Short Circuit Protection — High Magnetic Trip (Fixed at 16…20 x Ie)
y Overload Protection — Trip Class 10
1
2
Cat. No. 140M-C
3
4
5
6
Cat. No. 140M-D
Rated
Motor
Magnetic
Operational
Current
Trip
Current [A] Adjustment Current
(Ie)
Range [A]
[A]
Ultimate
Interrupting
Current [kA] (Icm)
400V
480V
Cat. No. 140M-F
Max. 3-phase Hp Ratings9
200V
230V
460V
Max kW, 3-Phase9
575V
230V
400/415V
500V
690V
Cat. No.
C-Frame
0.16
0.10…0.16
3.3
100
65
—
—
—
—
—
0.02
—
—
140M-C2T-A16
0.25
0.16…0.25
5.2
100
65
—
—
—
—
—
0.06
—
—
140M-C2T-A25
0.4
0.25…0.40
8.2
100
65
—
—
—
—
—
0.09
—
—
140M-C2T-A40
0.63
0.40…0.63
13
100
65
—
—
—
—
0.09
0.18
0.18
0.25
140M-C2T-A63
1
0.63…1.0
21
100
65
—
—
0.5
0.75
0.12
0.25
0.37
0.55
140M-C2T-B10
1.6
1.0…1.6
33
100
65
—
—
1
1
0.25
0.55
0.75
1.1
140M-C2T-B16
2.5
1.6…2.5
52
100
65
0.5
0.75
1.5
2
0.37
0.75
1.1
1.8
140M-C2T-B25
4
2.5…4
82
100
65
1
1
3
3
0.75
1.5
2.2
3
140M-C2T-B40
6.3
4…6.3
130
100
65
1.5
2
5
5
1.5
2.2
3
4
140M-C2T-B63
10
6.3…10
208
50
30
3
3
7.5
10
2.2
4
6.3
7.5
140M-C2T-C10
16
10…16
260
15
30
5
5
10
15
4
7.5
10
13
140M-C2T-C16
D-Frame
7
16
10…16
260
50
65
5
5
10
15
4
7.5
10
13
140M-D8T-C16
20
14.5…20
325
50
30
5
7.5
15
20
5.5
10
11
17
140M-D8T-C20
F-Frame
8
25
18…25
416
65
65
7.5
10
20
25
6.3
11
15
22
140M-F8T-C25
32
23…32
585
65
65
7.5
10
25
30
7.5
15
20
25
140M-F8T-C32
9 Horsepower/kW ratings shown in the table above are for reference. The final selection of the MPCB depends on the actual motor full load current and, in
North America, service factor.
9
10
11
12
13
Visit our website: www.ab.com/catalogs
2-10
Preferred availability cat. nos. are printed in bold
01_140M_Circuit_Breakers_A.qxd
4/22/2008
4:18 PM
Page 2-11
Bulletin 140M
Motor Circuit Protectors
Product Overview
Bulletin 140M Motor Circuit Protectors
y Current range 0.16…1200 A
y UL Listed/Recognized for motor loads
− Short-circuit protection
− Overload protection must be provided separately
y Visible trip indication
y High current limiting
y High switching capacity
The Bulletin 140M Motor Circuit Protectors provide short circuit
protection for individual motor loads. Factory-installed internal
accessories make installation and wiring easy.
Certifications (0.16…45 A)
Certifications (3…1200 A)
cULus Listed (File No. E54612,
Guide No. NLRV, NLRV7)
CCC
CE Marked
UR Recognized component
(File No. E224135, Guide
DKPU2)
CSA Certified (Cleass No.
3211-07)
Table of Contents
Product Selection —
Motor Circuit
Protectors ..................... 2-15
Approximate
Dimensions................... 2-49
!
Standards Compliance
1
IEC/EN 60947-1, 2, -4-1, -5-1
IEC/EN 60204-1
CSA, C22.2 No.14
UL 508
UL 489
2
Your order must include: cat.
no. of the Motor Circuit
Protector selected and, if
required, cat. no. of any
accessories.
General Information
3
4
Motor Circuit Protectors may provide the following protective and control functions.
y Disconnect for Motor Branch Circuit
y Branch-Circuit, Short-Circuit Protection (Magnetic Protection)
5
y Switching (Manual)
In North America, electrical codes require that an individual Motor Branch Circuit be protected by a UL/CSA Listed Fuse, Circuit Breaker or
Self-Protected Combination Motor Controller.
140M-C, D and F Frames:
The 140M-C, D and F frame Motor Circuit Protectors have one UL/CSA Listing – as Manual Motor Controllers (with optional approvals for
Motor Disconnect and Group Installation). In NEC/CEC Group Installations, these devices must be applied per the appropriate rules which
require the use of an upstream Branch-Circuit, Short-Circuit Protective Device (BCPD). See the table on page 2-19 for the specific ratings of
each Motor Circuit Protector.
The 140M-C, D and F Frame Motor Circuit Protectors are also UL/CSA Listed, together with a Bulletin 100C contactor and Bulletin 193
overload relay, as part of our Bulletin 103T and 107T Self-Protected IEC Combination Starters. These starters are then able to provide all of
the necessary NEC/CEC requirements for the protection and control of individual Motor Branch Circuits without additional protective devices.
6
7
140M-H, J and L Frames:
The 140M-H, J and L frame Motor Circuit Protectors are UL/CSA Recognized as Circuit Breakers as shown in the table on page 2-19. They
are UL/CSA Recognized, rather than UL/CSA Listed, since they only provide short circuit protection and not thermal overload protection for
the motor.
140M-H, J and L frame Motor Circuit Protectors (MCPs) are also UL/CSA Listed, together with a Bulletin 100C contactor and Bulletin 193
overload relay, as part of our Bulletin 113 IEC Combination Starters. These starters are then able to provide all of the necessary NEC/CEC
requirements for the protection and control of individual Motor Branch Circuits without additional protective devices.
8
9
10
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-11
01_140M_Circuit_Breakers_A.qxd
4/22/2008
4:19 PM
Page 2-12
Bulletin 140M
Motor Circuit Protectors
Product Overview, Continued/Catalog Number Explanation
Product Line Overview
!
1
2
C-Frame
D-Frame
F-Frame
H-Frame
J-Frame
L-Frame
Max. Current Ie
25 A
25 A
45 A
100 A
250 A
600 A
1200 A
Current Rating
0.16…2.5 A
2.5…25 A
25…45 A
3…100
70…250
125…600
640…1200
9
9
9
9
9
9
9
9
9
9
9
Short Circuit Protection
N-Frame
Standards Compliance:
3
4
CSA 22.2, No. 14
9
9
9
CSA 22.2, No. 5
—
—
—
UL 508 (Group Install.)
9
9
9
UL489 (Recognized)
—
—
—
9
9
9
9
IEC 60947-2
9
9
9
9
9
9
9
CE
9
9
9
9
9
9
9
CCC
9
9
9
—
—
—
—
Accessories
5
6
Ext. Rotary Operator
9
9
9
9
9
9
9
Flex Cable Operator
—
—
—
9
9
9
9
Auxiliary Contacts
9
9
9
9
9
9
9
Trip Indication Contacts
9
9
9
9
9
9
9
Cat. No. Explanation
Examples given in this section are for reference purposes. This basic explanation should not be used for product selection; not all
combinations will produce a valid catalog number.
7
140M – C – 2 – N – A63 – KN – CC – GJ
a
8
b
c
d
e
f
g
h
a
d
f, g, h
Bulletin Number
Protection Type
Factory-Installed Options
Code
Description
Code
Description
140M
Motor Circuit Protectors (MCPs)
N
Fixed Mag Only (13 x In)
P
Adj Mag Only (less than 13 x In)- MCPs
f
R
Adj Mag Only (greater than 13 x In) MCP's
Miscellaneous See page 2-33
9
b
Frame Size and Rating
10
11
Code
Description
C
25 A
D
25 A
F
45 A
H
125 A
J
250 A
L
400 A and 600 A
N
800 A and 1200 A
g
e
Aux/Trip Contacts See page 2-33
Current Range
Code
Description
Example
A
A = .10
A16 = 0.16
h
B
B = 1.0
B16 = 1.6
UV and Shunt Trips See page 2-33
C
C = 10
C16 = 16
D
D = 100
D16 = 160
E
E = 1000
E16 = 1600
c
12
13
Interrupting Rating / Breaking
Capacity
(Ic at 480V)
Code
Description
2
Normal Break
8
High Break
Visit our website: www.ab.com/catalogs
2-12
Preferred availability cat. nos. are printed in bold
01_140M_Circuit_Breakers_A.qxd
4/22/2008
4:19 PM
Page 2-13
Bulletin 140M
Motor Circuit Protectors
Product Selection
!
1
2
3
4
5
6
7
8
9
10
11
12
Group Motor Installation
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-13
01_140M_Circuit_Breakers_A.qxd
4/22/2008
4:19 PM
Page 2-14
Bulletin 140M
Motor Circuit Protectors
Product Selection, Continued
3-Phase Power Supply
!
1
2
3
4
5
6
7
8
9
10
11
12
Multi-Motor Installation
13
Visit our website: www.ab.com/catalogs
2-14
Preferred availability cat. nos. are printed in bold
01_140M_Circuit_Breakers_A.qxd
4/22/2008
4:19 PM
Page 2-15
Bulletin 140M
Motor Circuit Protectors
Product Selection, Continued
Motor Circuit Protectors
!
y Short-circuit protection — standard magnetic trip (fixed at 13 x Ie)
y Overload protection — none (magnetic trip only)
y For Trip Class 10 motor applications‡
1
2
Cat. No. 140M-D
Cat. No. 140M-C
Ultimate
Rated
Magnetic
Interrupting Current
Operational
Trip
[kA], (Icm)
Current [A] Current
(Ie)
400V
480V
[A]
Max. 3-phase Hp Ratings¹
200V
230V
460V
3
Cat. No. 140M-F
3-phase kW Ratings9
575V
230V
400/415V
500V
690V
Cat. No.
4
C-Frame
0.16
2.1
100
65
—
—
—
—
—
0.02
—
—
140M-C2N-A16
0.25
3.3
100
65
—
—
—
—
—
0.06
—
—
140M-C2N-A25
0.4
5.2
100
65
—
—
—
—
—
0.09
—
—
140M-C2N-A40
0.63
8.2
100
65
—
—
—
—
0.09
0.18
0.18
0.25
140M-C2N-A63
1
13
100
65
—
—
0.5
0.75
0.12
0.25
0.37
0.55
140M-C2N-B10
1.6
21
100
65
—
—
1
1
0.25
0.55
0.75
1.1
140M-C2N-B16
2.5
33
100
65
0.5
0.75
1.5
2
0.37
0.75
1.1
1.8
140M-C2N-B25
2
0.37
0.75
1.1
1.8
140M-D8N-B25
140M-D8N-B40
D-Frame
2.5
33
100
65
0.5
0.75
1.5
4
52
100
65
1
1
3
3
0.75
1.5
2.2
3
6.3
82
100
65
1.5
2
5
5
1.5
2.2
3
4
140M-D8N-B63
10
130
100
65
3
3
7.5
10
2.2
4
6.3
7.5
140M-D8N-C10
16
208
100
65
5
5
10
15
4
7.5
10
13
140M-D8N-C16
25
325
50
65
7.5
7.5
15
20
—
11
15
22
140M-D8N-C25
5
6
7
F-Frame
25
325
65
65
7.5
10
20
25
6.3
11
15
22
140M-F8N-C25
32
416
65
65
7.5
10
25
30
7.5
15
20
25
140M-F8N-C32
45
585
65
65
10
15
30
40
13
22
30
40
140M-F8N-C45
8
9 Horsepower/kW ratings shown in the table above are for reference. The final selection of the manual starter depends on the actual motor full load current
and, in North America, service factor.
‡ For heavy-duty starting applications (exceeding Trip Class 10), please consult your local Rockwell Automation sales office or Allen-Bradley distributor.
9
10
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-15
01_140M_Circuit_Breakers_A.qxd
4/22/2008
4:20 PM
Page 2-16
Bulletin 140M
Motor Circuit Protectors
Product Selection, Continued
Motor Circuit Protectors
!
y Short-Circuit Protection — Magnetic Trip (Adjustable at 3...10 x Ie)
y Overload Protection — None (Magnetic Trip Only)
1
2
Cat. No. 140M-H
Cat. No. 140M-J
3
4
5
6
Rated
Operational
Current [A]
(Ie)
Cat. No. 140M-L
Magnetic Trip Current [A]
3-phase Hp Ratings9
Cam Setting
A
B
C
D
E
F
G
H
I
200V
230V
460V
575V
3-phase kW Ratings9
230V
400/
415V
500V
690V
Cat. No.7
140M-H8P-B30
H-Frame
3
9
15
21
27
30
33
—
—
—
0.5
0.5
1.5
2
0.6
0.75
1.1
1.5
7
21
35
49
63
70
77
—
—
—
1.5
2
3
5
1.1
2.2
3
4
140M-H8P-B70
15
45
75
100
135
150
165
—
—
—
3
3
10
10
3
5.5
7.5
11
140M-H8P-C15
30
90
150
210
270
300
330
—
—
—
7.5
10
20
25
5.5
11
15
22
140M-H8P-C30
50
150
250
350
450
500
550
—
—
—
15
15
30
40
11
22
22
37
140M-H8P-C50
70
210
350
490
630
700
770
—
—
—
20
25
50
60
15
30
37
55
140M-H8P-C70
100
300
500
700
900
1000
1100
—
—
—
25
30
60
75
22
45
55
75
140M-H8P-D10
100
500
700
900
1100
1300
1500
—
—
—
30
30
75
100
30
55
75
110
140M-H8R-D10
100
500
600
700
800
900
1000
—
—
—
30
30
75
100
22
37
45
55
140M-J8P-D10
125
625
750
875
1000
1125
1250
—
—
—
40
40
100
125
22
45
55
90
140M-J8P-D12
150
750
900
1050
1200
1350
1500
—
—
—
50
50
100
150
30
55
75
110
140M-J8P-D15
175
875
1050
1225
1400
1575
1750
—
—
—
50
60
125
150
37
55
90
132
140M-J8P-D17
200
1000
1200
1400
1600
1800
2000
—
—
—
60
75
150
200
45
75
90
132
140M-J8P-D20
225
1125
1350
1575
1800
2025
2250
—
—
—
75
75
150
200
55
90
110
160
140M-J8P-D22
250
1250
1500
1750
2000
2250
2500
—
—
—
75
100
200
250
55
90
132
160
140M-J8P-D25
J-Frame
7
8
9
10
11
L-Frame
225
1125
1265
1410
1545
1690
1830
1970
2110
2250
50
60
125
150
55
90
110
160
140M-L8P-D22
250
1250
1405
1560
1720
1875
2030
2185
2340
2500
60
75
150
200
55
90
132
160
140M-L8P-D25
300
1500
1690
1875
2060
2250
2440
2625
2810
3000
75
75
150
200
55
110
160
200
140M-L8P-D30
350
1750
1970
2190
2410
2625
2840
3065
3285
3500
75
100
200
250
75
132
160
250
140M-L8P-D35
400
2000
2250
2500
2750
3000
3250
3500
3750
4000
100
100
250
300
90
160
200
250
140M-L8P-D40
450
2250
2530
2810
3098
3375
3660
3940
4220
4500
100
125
250
350
110
160
200
315
140M-L8P-D45
500
2500
2810
3125
3440
3750
4660
4375
4690
5000
125
150
300
400
110
200
250
355
140M-L8P-D50
600
3000
3375
3760
4110
4500
4880
5250
5630
6000
150
150
350
450
132
250
315
450
140M-L8P-D60
N-Frame
800
1600
2400
3200
4000
4800
5600
6400
—
—
150
200
400
500
160
250
355
500
140M-N8P-D80
1200
2400
3600
4800
6000
7200
8400
9600
—
—
250
300
600
700
200
250
500
710
140M-N8P-E12
9 The Hp and kW ratings shown are for reference only. They allow for a magnetic trip setting of at least up to 13X the motor FLA. However, the final selection of
the MCP should be made based on motor full load current and the requirements of local electrical codes.
7 The interrupting rating for MCPs is dependent upon the controller used. Please contact your local Rockwell Automation sales office or Allen-Bradley distributor
12
13
Visit our website: www.ab.com/catalogs
2-16
Preferred availability cat. nos. are printed in bold
01_140M_Circuit_Breakers_A.qxd
4/22/2008
4:21 PM
Page 2-17
Bulletin 140M
Motor Circuit Protectors
Application Ratings
UL/CSA Listed Application Ratings — Motor Protection Circuit Breaker (MPCB) Only
UL 508 — Manual Motor Controller
Group Motor Installation
Cat. No.
Max. Fuse
or C.B. per
NEC
Motor Disconnect
Tap Conductor Protection
UL 508 Self-Protected
(Type E) Combination
Motor Controller
UL 489 Inverse Time
C.B. w/UL 508 Motor
Overload Protection
!
Max. Short Circuit Current Max. Short Circuit Current Max. Short Circuit Current Max. Short Circuit Current Max. Short Circuit Current
[kA]
[kA]
[kA]
[kA]
[kA]
480V
600V
480V
600V
480V
600V
480Y/277V‡ 600Y/347V‡
480V
600V
C-Frame
140M-C2E-A16
450
65
47
65
47
65
47
65
47
—
—
140M-C2E-A25
450
65
47
65
47
65
47
65
47
—
—
140M-C2E-A40
450
65
47
65
47
65
47
65
47
—
—
140M-C2E-A63
450
65
47
65
47
65
47
65
47
—
—
140M-C2E-B10
450
65
47
65
47
65
47
65
47
—
—
140M-C2E-B16
450
65
47
65
47
65
47
65
47
—
—
140M-C2E-B25
450
65
30
65
30
65
30
65
30
—
—
140M-C2E-B40
450
65
25
65
25
65
25
65
25
—
—
140M-C2E-B63
450
65
30
65
30
65
—
65
—
—
—
140M-C2E-C10
450
65
30
65
30
65
—
65
—
—
—
140M-C2E-C16
450
30
30
30
30
30
—
30
—
—
—
140M-C2E-C20
450
30
30
10
10
10
—
10
—
—
—
140M-C2E-C25
450
25
10
10
5
—
—
—
—
—
—
D-Frame
140M-D8E-B25
450
65
30
65
30
65
30
65
30
—
—
140M-D8E-B40
450
65
30
65
30
65
30
65
30
—
—
140M-D8E-B63
450
65
30
65
30
65
30
65
30
—
—
140M-D8E-C10
450
65
30
65
30
65
30
65
30
—
—
140M-D8E-C16
450
65
30
65
30
65
30
65
30
—
—
140M-D8E-C20
450
65
30
65
30
65
—
65
—
—
—
140M-D8E-C25
450
30
30
30
30
30
—
30
—
—
—
F-Frame
140M-F8E-C10
600
65
30
65
30
65
30
65
30
—
—
140M-F8E-C16
600
65
30
65
30
65
30
65
30
—
—
140M-F8E-C20
600
65
30
65
30
65
30
65
30
—
—
140M-F8E-C25
600
65
30
65
30
65
30
65
30
—
—
140M-F8E-C32
600
65
30
65
30
65
30
65
30
—
—
140M-F8E-C45
600
65
18
65
18
65
—
65
—
—
—
1
2
3
4
5
6
7
CMN-Frame
140-CMN-2500
1000
65
42
—
—
—
—
—
—
—
—
140-CMN-4000
1000
65
42
—
—
—
—
—
—
—
—
140-CMN-6300
1000
42
18
—
—
—
—
—
—
—
—
140-CMN-9000
1000
35
10
—
—
—
—
—
—
—
—
140M-I8E-C80
—
—
—
—
—
—
—
—
—
65
30
140M-I8E-D10
—
—
—
—
—
—
—
—
—
65
30
140M-I8E-D16
—
—
—
—
—
—
—
—
—
65
30
140M-I8E-D20
—
—
—
—
—
—
—
—
—
65
30
140M-J2E-C50
—
—
—
—
—
—
—
—
—
25
18
140M-J2E-D10
—
—
—
—
—
—
—
—
—
25
18
140M-J2E-D16
—
—
—
—
—
—
—
—
—
25
18
140M-J2E-D25
—
—
—
—
—
—
—
—
—
25
18
8
I-Frame
9
J-Frame
140M-J8E-C50
—
—
—
—
—
—
—
—
—
65
25
140M-J8E-D10
—
—
—
—
—
—
—
—
—
65
25
140M-J8E-D16
—
—
—
—
—
—
—
—
—
65
25
140M-J8E-D25
—
—
—
—
—
—
—
—
—
65
25
10
11
L-Frame
140M-L2E-D25
—
—
—
—
—
—
—
—
—
25
18
140M-L2E-D40
—
—
—
—
—
—
—
—
—
25
18
140M-L2E-D60
—
—
—
—
—
—
—
—
—
25
18
140M-L2E-D63
—
—
—
—
—
—
—
—
—
25
18
140M-L8E-D25
—
—
—
—
—
—
—
—
—
65
25
140M-L8E-D40
—
—
—
—
—
—
—
—
—
65
25
140M-L8E-D60
—
—
—
—
—
—
—
—
—
65
25
140M-L8E-D63
—
—
—
—
—
—
—
—
—
65
25
‡ For full voltage (delta) ratings above 277V or 347V, follow the NEC or CEC rules for group motor applications.
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-17
12
13
01_140M_Circuit_Breakers_A.qxd
4/22/2008
4:21 PM
Page 2-18
Bulletin 140M
Motor Circuit Protectors
Application Ratings, Continued
UL/CSA Listed Application Ratings — Motor Protection Circuit Breaker (MPCB) Only, Continued
!
UL 508 Manual Motor Controller
Group Motor Installation
1
2
3
4
Cat. No.
Max. Fuse or
C.B. per NEC
Max. Short Circuit Current
[kA]
480V
600V
Motor Disconnect
Tap Conductor Protection
UL 508 Self-Protected
(Type E) Combination
Motor Controller
Max. Short Circuit Current
[kA]
Max. Short Circuit Current
[kA]
Max. Short Circuit Current
[kA]
480V
600V
480V
600V
480Y/277V‡
600Y/347V‡
C-Frame
140M-C2T-A16
450
65
47
65
47
65
47
65
47
140M-C2T-A25
450
65
47
65
47
65
47
65
47
140M-C2T-A40
450
65
47
65
47
65
47
65
47
140M-C2T-A63
450
65
47
65
47
65
47
65
47
140M-C2T-B10
450
65
47
65
47
65
47
65
47
140M-C2T-B16
450
65
47
65
47
65
30
65
30
140M-C2T-B25
450
65
25
65
25
65
25
65
25
140M-C2T-B40
450
65
30
65
30
65
—
65
—
140M-C2T-B63
450
65
30
65
30
65
—
65
—
140M-C2T-C10
450
30
30
30
30
30
—
30
—
140M-C2T-C16
450
30
30
10
10
10
—
10
—
D-Frame
140M-D8T-C16
450
65
30
65
30
65
30
65
30
140M-D8T-C20
450
30
30
30
30
30
—
30
—
F-Frame
5
140M-F8T-C25
600
65
30
65
30
65
30
65
30
140M-F8T-C32
600
65
18
65
18
65
18
65
18
‡ For full voltage (delta) ratings above 277V or 347V, follow the NEC or CEC rules for group motor applications.
6
7
8
9
10
11
12
13
Visit our website: www.ab.com/catalogs
2-18
Preferred availability cat. nos. are printed in bold
01_140M_Circuit_Breakers_A.qxd
4/22/2008
4:22 PM
Page 2-19
Bulletin 140M
Motor Circuit Protectors
Application Ratings, Continued
UL Listed Application Ratings — Motor Circuit Protectors Only§
UL 489 Instantaneous Trip Circuit
Breaker (Magnetic Only)
Manual Motor Controller
Group Motor Installation
Cat. No.
Max. Fuse or C.B.
per NEC
Max. Short Circuit Current [kA]
480V
Motor Disconnect
Motor Circuit Protector
Max. Short Circuit Current [kA]
Max. Short Circuit Current [kA]‡
600V
480V
600V
480V
600V
C-Frame
140M-C2N-A16
450
65
47
65
47
—
—
140M-C2N-A25
450
65
47
65
47
—
—
140M-C2N-A40
450
65
47
65
47
—
—
140M-C2N-A63
450
65
47
65
47
—
—
140M-C2N-B10
450
65
47
65
47
—
—
140M-C2N-B16
450
65
47
65
47
—
—
140M-C2N-B25
450
65
30
65
30
—
—
450
65
30
65
30
—
—
140M-D8N-B40
450
65
30
65
30
—
—
140M-D8N-B63
450
65
30
65
30
—
—
140M-D8N-C10
450
65
30
65
30
—
—
140M-D8N-C16
450
65
30
65
30
—
—
140M-D8N-C25
450
30
30
30
30
—
—
140M-F8N-C25
600
65
30
65
30
—
—
140M-F8N-C32
600
65
30
65
30
—
—
140M-F8N-C45
600
65
18
65
18
—
—
140M-H8P-B30
—
—
—
—
—
65
25
140M-H8P-B70
—
—
—
—
—
65
25
140M-H8P-C15
—
—
—
—
—
65
25
140M-H8P-C30
—
—
—
—
—
65
25
140M-H8P-C50
—
—
—
—
—
65
25
140M-H8P-C70
—
—
—
—
—
65
25
140M-H8P-D10
—
—
—
—
—
65
25
140M-H8R-D10
—
—
—
—
—
65
25
140M-J8P-C70
—
—
—
—
—
65
25
140M-J8P-C90
—
—
—
—
—
65
25
140M-J8P-D10
—
—
—
—
—
65
25
140M-J8P-D12
—
—
—
—
—
65
25
140M-J8P-D15
—
—
—
—
—
65
25
140M-J8P-D17
—
—
—
—
—
65
25
140M-J8P-D20
—
—
—
—
—
65
25
140M-J8P-D22
—
—
—
—
—
65
25
140M-J8P-D25
—
—
—
—
—
65
25
1
2
3
D-Frame
140M-D8N-B25
!
4
F-Frame
5
H-Frame
6
7
J-Frame
8
9
L-Frame
140M-L8P-D22
—
—
—
—
—
65
25
140M-L8P-D25
—
—
—
—
—
65
25
140M-L8P-D30
—
—
—
—
—
65
25
140M-L8P-D35
—
—
—
—
—
65
25
140M-L8P-D40
—
—
—
—
—
65
25
140M-L8P-D45
—
—
—
—
—
65
25
140M-L8P-D50
—
—
—
—
—
65
25
140M-L8P-D60
—
—
—
—
—
65
25
10
11
N-Frame
140M-N8P-D80
—
—
—
—
—
65
35
140M-N8P-E12
—
—
—
—
—
65
35
12
§ Separate overload protection is required.
‡ The interrupting rating for MCPs is dependent upon the controller used. Contact your local Rockwell Automation sales office or Allen-Bradley distributor for
further information.
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-19
13
01_140M_Circuit_Breakers_A.qxd
4/22/2008
4:22 PM
Page 2-20
Bulletin 140M
Motor Circuit Protectors
Application Ratings, Continued
UL Listed Application Ratings - Motor Protection Circuit Breakers with Bulletin 100-C Contactors
!
UL 508 Manual Motor Controller
Group Motor Installation
1
Cat. No.
Max.
Fuse or
C.B.
Minimum
per
Contactor
NEC
Size
UL 508 Type F
Combination
Motor Controller
Motor
Disconnect
Max. Short
Circuit Current
[kA]
Max. Short
Circuit Current
[kA]
480V
480V
600V
600V
Minimum
Contactor
Size
UL 508 Type E
Self-Protected Combination
Motor Controller
Max. Short Circuit Current
[kA]
480Y/277V§ 600Y/347V§
Minimum
Contactor
Size
Max. Short Circuit Current
[kA]
480Y/277V§ 600Y/347V§
C-Frame
140M-C2E-A16
140M-C2E-A25
140M-C2E-A40
140M-C2E-A63
140M-C2E-B10
140M-C2E-B16
140M-C2E-B25
140M-C2E-B40
140M-C2E-B63
140M-C2E-C10
140M-C2E-C16
140M-C2E-C20
140M-C2E-C25
140M-C2E-C25
450
450
450
450
450
450
450
450
450
450
450
450
450
450
100-C09
100-C09
100-C09
100-C09
100-C09
100-C09
100-C09
100-C09
100-C09
100-C09
100-C12
100-C16
100-C23
100-C30
65
65
65
65
65
65
65
65
65
65
30
30
25
25
47
47
47
47
47
47
30
25
30
30
30
30
10
10
65
65
65
65
65
65
65
65
65
65
30
10
10
10
47
47
47
47
47
47
30
25
30
30
30
10
10
5
140M-D8E-B25
140M-D8E-B25
140M-D8E-B40
140M-D8E-B63
140M-D8E-C10
140M-D8E-C16
140M-D8E-C20
140M-D8E-C25
450
—
450
450
450
450
450
450
100-C09
—
100-C09
100-C09
100-C09
100-C12
100-C23
100-C23
65
—
65
65
65
65
65
30
30
—
30
30
30
30
30
30
65
—
65
65
65
65
65
30
30
—
30
30
30
30
30
30
8
140M-F8E-C10
140M-F8E-C16
140M-F8E-C20
140M-F8E-C25
140M-F8E-C32
140M-F8E-C45
600
600
600
600
600
600
100-C30
100-C30
100-C30
100-C30
100-C30
100-C37
65
65
65
65
65
65
30
30
30
30
30
18
65
65
65
65
65
65
30
30
30
30
30
18
9
140-CMN-2500
140-CMN-4000
140-CMN-6300
140-CMN-9000
1000
1000
1000
1000
100-C16
100-C30
100-C43
100-C72
65
65
42
35
42
42
18
10
—
—
—
—
—
—
—
—
2
3
4
5
6
100-C09
100-C09
100-C09
100-C09
100-C09
100-C09
100-C09
100-C09
100-C09
100-C09
100-C12
100-C23
—
—
65
65
65
65
65
65
65
65
65
65
30
10
—
—
47
47
47
47
47
47
30
30
—
—
—
—
—
—
100-C09
100-C09
100-C09
100-C09
100-C09
100-C09
100-C09
—
—
—
—
—
—
—
65
65
65
65
65
65
65
—
—
—
—
—
—
—
47
47
47
47
47
47
—
—
—
—
—
—
—
—
65
—
65
65
65
65
65
65
30
—
30
30
30
30
—
—
100-C09
100-C23
100-C23
100-C30
100-C30
100-C30
100-C30
100-C30
65
65
65
65
65
65
65
30
—
30
30
30
30
30
—
—
65
65
65
65
65
65
30
30
30
30
30
—
100-C30
100-C30
100-C30
100-C30
100-C30
100-C37
65
65
65
65
65
65
30
30
30
30
30
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
D-Frame
100-C09
—
100-C09
100-C09
100-C09
100-C12
100-C23
100-C23
F-Frame
7
100-C30
100-C30
100-C30
100-C30
100-C30
100-C37
CMN-Frame
—
—
—
—
§ For full voltage (delta) ratings above 277V or 347V, follow the NEC or CEC rules for group motor applications.
10
11
12
13
Visit our website: www.ab.com/catalogs
2-20
Preferred availability cat. nos. are printed in bold
01_140M_Circuit_Breakers_A.qxd
4/22/2008
4:22 PM
Page 2-21
Bulletin 140M
Motor Circuit Protectors
Application Ratings, Continued
UL Listed Application Ratings - Motor Circuit Protectors with Bulletin 100-C Contactors§
UL 508 Manual Motor Controller
Group Motor Installation
Cat. No.
Max. Fuse or
C.B. per NEC
Minimum
Contactor
Size
Motor Disconnect
Max. Short Circuit Current
[kA]
480V
Max. Short Circuit Current
[kA]
600V
UL 508 Type E (Self-Protected) Combination
Motor Controller
Max. Short
Circuit
Current [kA]
Max. Short
Circuit
Current [kA]
480Y/277V7
600Y/347V7
1
2
480V
600V
Minimum
Contactor
Size
65
65
65
65
65
65
65
47
47
47
47
47
47
30
100-C09
100-C09
100-C09
100-C09
100-C09
100-C09
100-C09
65
65
65
65
65
65
65
47
47
47
47
47
47
—
65
—
65
65
65
65
30
30
—
30
30
30
30
30
100-C09
100-C23
100-C23
100-C30
100-C30
100-C30
100-C30
65
65
65
65
65
65
65
—
30
30
30
30
30
—
65
65
65
30
30
18
100-C30
100-C30
100-C37
65
65
65
30
30
—
C-Frame
140M-C2N-A16
140M-C2N-A25
140M-C2N-A40
140M-C2N-A63
140M-C2N-B10
140M-C2N-B16
140M-C2N-B25
450
450
450
450
450
450
450
100-C09
100-C09
100-C09
100-C09
100-C09
100-C09
100-C09
65
65
65
65
65
65
65
47
47
47
47
47
47
30
140M-D8N-B25
140M-D8N-B25
140M-D8N-B40
140M-D8N-B63
140M-D8N-C10
140M-D8N-C16
140M-D8N-C25
450
—
450
450
450
450
450
100-C09
—
100-C09
100-C09
100-C09
100-C12
100-C23
65
—
65
65
65
65
30
30
—
30
30
30
30
30
140M-F8N-C25
140M-F8N-C32
140M-F8N-C45
600
600
600
100-C23
100-C30
100-C37
65
65
65
30
30
18
!
D-Frame
3
4
F-Frame
5
§ Separate overload protection is required.
7 For full-voltage (delta) ratings above277V or 347V, follow the NEC or CEC rules for group motor applications.
6
7
8
9
10
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-21
01_140M_Circuit_Breakers_A.qxd
4/22/2008
4:22 PM
Page 2-22
Bulletin 140M
Motor Circuit Protectors
Application Ratings, Continued
Definition of Type 2 Short Circuit Coordination:
y The contactor or starter must not endanger persons or plant in the event of a short circuit.
y No damage to the motor protection device or other parts may occur with the exception of welding of the contactor or starter contacts if
these can be easily separated without appreciable deformation (such as with a screwdriver).
!
1
In the event of short circuit, fast-opening, current-limiting Bulletin 140M Motor Protection Circuit Breakers make it possible to build
economical, fully short-circuit coordinated starter combinations with Type 2 coordination.
Type 2 Coordination 400V
Max. Short Circuit Current
[kA]
Cat. No.
2
400V
For Use With Contactors
Below (or larger)
Standard Trip
High Trip
Mag Only Trip
140M-C2E-A16
—
140M-C2N-A16
100
100-C09
140M-C2E-A25
140M-C2T-A16
140M-C2N-A25
100
100-C09
140M-C2E-A40
140M-C2T-A25
140M-C2N-A40
100
100-C09
140M-C2E-A63
140M-C2T-A40
140M-C2N-A63
100
100-C09
140M-C2E-B10
140M-C2T-A63
140M-C2N-B10
100
100-C09
140M-C2E-B16
140M-C2T-B10
140M-C2N-B16
100
100-C09
140M-C2E-B25
140M-C2T-B16
140M-C2N-B25
50
100-C09
140M-C2E-B40
140M-C2T-B25
—
50
100-C09
140M-C2E-B63
140M-C2T-B40
—
50
100-C09
140M-C2E-C10
140M-C2T-B63
—
50
100-C09
140M-C2E-C16
140M-C2T-C10
—
50
100-C129
140M-C2E-C20
140M-C2T-C16
—
—
—
140M-C2E-C25
—
—
—
—
C-Frame
3
4
5
D-Frame
6
7
140M-D8E-B25
—
140M-D8N-B25
100
100-C09
140M-D8E-B40
—
140M-D8N-B40
100
100-C09
140M-D8E-B63
—
140M-D8N-B63
100
100-C09
140M-D8E-C10
—
140M-D8N-C10
65
100-C09
140M-D8E-C16
—
140M-D8N-C16
65
100-C12
140M-D8E-C20
140M-D8T-C16
—
65
100-C23
140M-D8E-C25
140M-D8T-C20
140M-D8N-C25
50
100-C23
140M-F8E-C10
—
—
100
100-C09
140M-F8E-C16
—
—
100
100-C12
140M-F8E-C20
—
—
100
100-C23
140M-F8E-C25
—
140M-F8N-C25
100
100-C30
140M-F8E-C32
140M-F8T-C25
140M-F8N-C32
100
100-C30
140M-F8E-C45
140M-F8T-C32
140M-F8N-C45
100
100-C37
F-Frame
8
CMN-Frame
9
10
140-CMN-2500
—
—
65
100-C16
140-CMN-4000
—
—
65
100-C30
140-CMN-6300
—
—
42
100-C43
140-CMN-9000
—
—
35
100-C72
9 Cat. No. 100-C16 contactors Type 1 only
11
12
13
Visit our website: www.ab.com/catalogs
2-22
Preferred availability cat. nos. are printed in bold
01_140M_Circuit_Breakers_A.qxd
4/22/2008
4:23 PM
Page 2-23
Bulletin 140M
Motor Circuit Protectors
Application Ratings, Continued
Type 2 Coordination 480V
Max. Short Circuit Current
[kA]
Cat. No.
Standard Trip
High Trip
Mag Only Trip
480V
!
For Use With Contactors
Below (or larger)
C-Frame
140M-C2E-A16
—
140M-C2N-A16
65
100-K05, 100-C09
140M-C2E-A25
140M-C2T-A16
140M-C2N-A25
65
100-K05, 100-C09
140M-C2E-A40
140M-C2T-A25
140M-C2N-A40
65
100-K05, 100-C09
140M-C2E-A63
140M-C2T-A40
140M-C2N-A63
65
100-K05, 100-C09
140M-C2E-B10
140M-C2T-A63
140M-C2N-B10
65
100-K05, 100-C09
140M-C2E-B16
140M-C2T-B10
140M-C2N-B16
65
100-K05, 100-C09
140M-C2E-B25
140M-C2T-B16
140M-C2N-B25
50
100-C16
140M-C2E-B40
140M-C2T-B25
—
50
100-C30
140M-C2E-B63
140M-C2T-B40
—
50
100-C30
140M-C2E-C10
140M-C2T-B63
—
50
100-C30
140M-C2E-C16
140M-C2T-C10
—
10
100-C30
140M-C2E-C20
140M-C2T-C16
—
10
100-C30
140M-C2E-C25
—
—
10
100-C30
—
140M-D8N-B25
65
100-C09
140M-D8E-B40
—
140M-D8N-B40
65
100-C09
140M-D8E-B63
—
140M-D8N-B63
65
100-C09
140M-D8E-C10
—
140M-D8N-C10
65
100-C09
140M-D8E-C16
—
140M-D8N-C16
65
100-C12
140M-D8E-C20
140M-D8T-C16
—
65
100-C23
140M-D8E-C25
140M-D8T-C20
140M-D8N-C25
65
100-C23
2
3
D-Frame
140M-D8E-B25
1
4
5
F-Frame
140M-F8E-C10
—
—
65
100-C09
140M-F8E-C16
—
—
65
100-C12
140M-F8E-C20
—
—
65
100-C16
140M-F8E-C25
—
140M-F8N-C25
65
100-C23
140M-F8E-C32
140M-F8T-C25
140M-F8N-C32
65
100-C30
140M-F8E-C45
140M-F8T-C32
140M-F8N-C45
65
100-C37
140-CMN-2500
—
—
65
100-C16
140-CMN-4000
—
—
65
100-C30
140-CMN-6300
—
—
42
100-C43
140-CMN-9000
—
—
35
100-C72
6
7
CMN-Frame
8
9
10
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-23
01_140M_Circuit_Breakers_A.qxd
4/22/2008
4:23 PM
Page 2-24
Bulletin 140M
Motor Circuit Protectors
Application Ratings, Continued
Type 2 Coordination 600V
!
Max. Short Circuit
Current [kA]
Cat. No.
600V
Max Fuse or C.B per
NEC
For Use With Contactors
Below (or larger)
Standard Trip
High Trip
Mag Only Trip
140M-C2E-A16
—
140M-C2N-A16
47
450
100-K05, 100-C09
140M-C2E-A25
140M-C2T-A16
140M-C2N-A25
47
450
100-K05, 100-C09
140M-C2E-A40
140M-C2T-A25
140M-C2N-A40
47
450
100-K05, 100-C09
140M-C2E-A63
140M-C2T-A40
140M-C2N-A63
47
450
100-K05, 100-C09
140M-C2E-B10
140M-C2T-A63
140M-C2N-B10
47
450
100-K05, 100-C09
140M-C2E-B16
140M-C2T-B10
140M-C2N-B16
47
450
100-K05, 100-C09
140M-C2E-B25
140M-C2T-B16
140M-C2N-B25
10
450
100-C16
140M-C2E-B40
140M-C2T-B25
—
10
450
100-C16
C-Frame
1
2
3
4
5
140M-C2E-B63
140M-C2T-B40
—
5
450
100-C23
140M-C2E-C10
140M-C2T-B63
—
5
450
100-C30
140M-C2E-C16
140M-C2T-C10
—
5
450
100-C30
140M-C2E-C20
140M-C2T-C16
—
5
450
100-C30
140M-C2E-C25
—
—
5
450
100-C30
D-Frame
140M-D8E-B25
—
140M-D8N-B25
30
450
100-C30
140M-D8E-B40
—
140M-D8N-B40
30
450
100-C30
140M-D8E-B63
—
140M-D8N-B63
30
450
100-C30
140M-D8E-C10
—
140M-D8N-C10
30
450
100-C30
140M-D8E-C16
—
140M-D8N-C16
30
450
100-C30
140M-D8E-C20
140M-D8T-C16
—
5
450
100-C30
140M-D8E-C25
140M-D8T-C20
140M-D8N-C25
5
450
100-C30
140M-F8E-C10
—
—
30
600
100-C30
140M-F8E-C16
—
—
30
600
100-C30
140M-F8E-C20
—
—
30
600
100-C30
140M-F8E-C25
—
140M-F8N-C25
30
600
100-C30
140M-F8E-C32
140M-F8T-C25
140M-F8N-C32
30
600
100-C30
140M-F8E-C45
140M-F8T-C32
140M-F8N-C45
10
600
100-C37
F-Frame
6
7
CMN-Frame
8
140-CMN-2500
—
—
42
1000
100-C16
140-CMN-4000
—
—
42
1000
100-C30
140-CMN-6300
—
—
18
1000
100-C43
140-CMN-9000
—
—
10
1000
100-C72
9
10
11
12
13
Visit our website: www.ab.com/catalogs
2-24
Preferred availability cat. nos. are printed in bold
01_140M_Circuit_Breakers_A.qxd
4/22/2008
4:23 PM
Page 2-25
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Accessories
Description
!
Operator Position 9
OFF
ON
Tripped
Term.
No.
Front-Mounted
Auxiliary Contact
1-pole or 2-pole
No additional space
required
-Only 1 per MPCB
Description
O
X
O
13-14
X
O
X
11-12
N.C. Aux
O
X
O
13-14
N.O. Aux
Connection Diagram
7
N.O. Aux
X
O
X
21-22
N.C. Aux
O
X
O
13-14
N.O. Aux
13
21
14
22
For Use
With
140M-C,
D, F
140M-C-AFA10
140M-C,
D, F
140M-C-AFA01
140M-C,
D, F
140M-C-AFA11
X
O
23-24
1
2
3
4
140M-C,
D, F
O
Cat. No.
140M-C-AFA20
N.O. Aux
5
X
O
X
11-12
N.C. Aux
140M-C,
D, F
Right Side-Mounted
Auxiliary Contact
2-pole
Adds 9 mm to the
width of the device
- 2 per MPCB
X
O
X
21-22
N.C. Aux
O
X
O
33-34
N.O. Aux
O
X
O
43-44
N.O. Aux
X
O
X
31-32
N.C. Aux
140M-C-AFA02
6
140M-C,
D, F
140M-C-ASA20
140M-C,
D, F
140M-C-ASA02
140M-C,
D, F
140M-C-ASA11
7
31 41
32
X
O
X
41-42
N.C. Aux
O
X
O
33-34
N.O. Aux
X
O
X
41-42
42
N.C. Aux
8
9
9 X = Contact Closed; O = Contact Open
7
10
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-25
01_140M_Circuit_Breakers_A.qxd
4/22/2008
4:23 PM
Page 2-26
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Accessories, Continued
Description
!
Operator Position 9
OFF
1
O
Front-Mounted Trip
Contact
2-pole
Indicates tripping of
device
No additional space
required
2
X
Tripped
O
Term.
No.
Description
13-14
N.O. Aux
O
O
X
27-28
N.O. Trip
(Short-Circuit
& Overload)
X
O
X
11-12
N.C. Aux
27-28
N.O. Trip
(Short-Circuit
& Overload)
57-58
N.O. Trip
(Short-Circuit
& Overload)
O
O
O
O
O
X
X
X
67-68
N.O. Trip
57-58
N.O. Trip
(Short-Circuit
& Overload)
4
O
Right-Side Mounted
Trip Contact
2-pole
Indicates tripping of
Motor Protection
Circuit Breaker
Adds 9 mm to the
width of the circuit
breaker
- Only 1 per MPCB
- A right-side mounted
auxiliary contact may
be tandem mounted
on top of this Trip
Contact
5
6
7
8
Connection Diagram
7
O
X
X
X
O
65-66
N.C. Trip
X
X
O
55-56
N.C. Trip
(Short-Circuit
& Overload)
O
O
X
67-68
N.O. Trip
X
X
O
55-56
N.C. Trip
(Short-Circuit
& Overload)
X
X
O
65-66
N.C. Trip
O
O
X
77-78
N.O. Trip
(Short-Circuit)
65-66
N.C. Trip
(Short-Circuit)
X
X
O
9 X = Contact Closed; O = Contact Open
7
9
10
11
12
13
Visit our website: www.ab.com/catalogs
2-26
For Use
With
Cat. No.
140M-C,
D, F
140M-C-AFAR10A10
140M-C,
D, F
140M-C-AFAR10A01
11 27
O
3
ON
Preferred availability cat. nos. are printed in bold
12
28
57 67
I>>
58
140M-C,
140M-C-ASAR10M10
D, F
68
57 65
I>>
140M-C,
140M-C-ASAR10M01
D, F
58 66
140M-C,
140M-C-ASAR01M10
D, F
140M-C,
140M-C-ASAR01M01
D, F
140M-C,
D, F
140M-C-ASAM11
02_140M_Circuit_Protectors_A.qxd
4/23/2008
11:05 AM
Page 2-27
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Accessories, Continued
Description
Operator Position9
OFF
O
ON
X
!
Tripped
O
Term.
No.
Description
13-14
N.O. Aux
Connection Diagram7
For Use
With
Cat. No.
140-CMN
140-CA20
1
Front-Mounted Auxiliary
Contact
Internal
2-pole
-1 per MPCB
O
X
O
23-24
N.O. Aux
X
O
X
11-12
N.C. Aux
X
O
X
21-22
N.C. Aux
O
X
O
13-14
N.O. Aux
X
O
X
21-22
N.C. Aux
O
O
X
37-38
N.O. Trip
(Overload)
O
O
X
43-44
N.O. Trip
(Short-Circuit)
X
X
O
35-36
N.C. Trip
(Overload)
X
X
O
41-42
N.C. Trip
(Short-Circuit)
2
140-CMN
140-CA02
11 21
140-CMN
140-CA02
3
12 22
Front-Mounted TripIndicating Auxiliary
Contact
Internal
2-pole
-1 per MPCB
X
X
O
35-36
N.C. Trip
(Overload)
O
O
X
43-44
N.O. Trip
(Short-Circuit)
O
O
X
37-38
N.O. Trip
(Overload)
X
X
O
41-42
N.C. Trip
(Short-Circuit)
140-CMN
140-CA11
140-CMN 140-CT10-10
4
5
6
140-CMN 140-CT01-01
7
140-CMN 140-CT01-10
8
9
140-CMN 140-CT10-01
10
9 X = Contact Closed
O = Contact Open
7
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-27
02_140M_Circuit_Protectors_A.qxd
4/23/2008
11:05 AM
Page 2-28
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Accessories, Continued
Description
Connection Diagram9
Trip Rating
For Use With
24V, 60 Hz
!
Undervoltage Trip
Left-side mounted
Adds 18 mm to the width
of the circuit breaker
Automatically trips
MPCB/MCP when voltage
falls below 35…70%
1
2
3
Undervoltage Trip
Left-side mounted
2 early make contacts
integrated
Adds 18 mm to the width
of the circuit breaker
Automatically trips
MPCB/MCP when voltage
falls below 35…70%
4
5
6
Shunt Trip
Left-side mounted
Adds 18 mm to the width
of the circuit breaker
Provides remote tripping of
the MPCB/MCP
7
8
Undervoltage Trip Unit
Internal, front-mounted
Integrated short-circuit trip
indication
Automatically trips MPCB
when voltage falls below
35…70%
9
10
Shunt Trip Unit
Internal, front-mounted
Integrated short-circuit trip
indication
Provides remote tripping of
the MPCB
11
24V, 50 Hz
140M-C-UXK
120V, 60 Hz
140M-C-UXD
110V, 50 Hz
140M-C-UXC
208V, 60 Hz
140M-C-UXH
220…230V, 50 Hz
240…260V, 60 Hz
140M-C, D, F
140M-C-UXF
140M-C-UXA
277V, 60 Hz
140M-C-UXT
380…400V, 50 Hz
140M-C-UXN
480V, 60 Hz/415V, 50 Hz
140M-C-UXB
575V, 60 Hz/500V, 50 Hz
140M-C-UXM
600V, 60 Hz
140M-C-UXVC
24V, 60 Hz
140M-C-UCJ
24V, 50 Hz
140M-C-UCK
120V, 60 Hz
140M-C-UCD
110V, 50 Hz
140M-C-UCC
208V, 60 Hz
140M-C-UCH
220…230V, 50 Hz
240…260V, 60 Hz
140M-C, D, F
140M-C-UCF
140M-C-UCA
277V, 60 Hz
140M-C-UCT
380…400V, 50 Hz
140M-C-UCN
480V, 60 Hz/415V, 50 Hz
140M-C-UCB
575V, 60 Hz/500V, 50 Hz
140M-C-UCM
600V, 60 Hz
140M-C-UCVC
24V, 60 Hz
140M-C-SNJ
24V, 50 Hz
140M-C-SNK
120V, 60 Hz
140M-C-SND
208V, 60 Hz
140M-C-SNH
220…230V, 50 Hz
140M-C-SNF
240…260V, 60 Hz
140M-C-SNA
277V, 60 Hz
140M-C, D, F
380…400V, 50 Hz
140M-C-SNT
140M-C-SNN
480V, 60 Hz/415V, 50 Hz
140M-C-SNB
575V, 60 Hz/500V, 50 Hz
140M-C-SNM
600V, 60 Hz
140M-C-SNVC
24V DC
140M-C-SNZJ
24V, 50/60 Hz
140-CUV-KJ
110V, 50 Hz/120V, 60 Hz
140-CUV-D
140-CMN
220V, 50 Hz/240V, 60 Hz
140-CUV-A
24V, 50/60 Hz
140-CRT-KJ
110V, 50 Hz/120V, 60 Hz
140-CRT-D
140-CMN
220V, 50 Hz/240V, 60 Hz
9
12
13
Visit our website: www.ab.com/catalogs
2-28
Cat. No.
140M-C-UXJ
Preferred availability cat. nos. are printed in bold
140-CRT-A
02_140M_Circuit_Protectors_A.qxd
4/23/2008
11:05 AM
Page 2-29
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Accessories, Continued
Description
For Use With
Cat. No.
!
Anti-Tamper Shield
Provides protection against inadvertent adjustment of the current setting
Lockable Twist Knob
For 1 padlock 4…6 mm (1/4 in.) dia. shackle
Can be locked in OFF position
10 pcs/pkg
140M-C, D, F
140M-C-CA
Black
140M-C, D, F
140M-C-KN
Red/Yellow
140M-C/-D
140M-C-KRY
Red/Yellow
140M-F
140M-F-KRY
Black
Padlockable Operating Knob
Accepts 8 mm (5/16 in.) padlock — up to three padlocks
Permits padlocking in the off position
Door Coupling Handle
For 3 padlocks 4…8 mm (5/16 in.) in diameter
IP66 Protection/Type 1, 4, 4X, 12
Interlock override capability
Can be modified for locking in ON position
Ships with coupling — order extension shaft and legend plate separately
Mounting depth (adapter-door):
140-C: 105.5 mm ± 5 mm (4.5 in. ± 3/16 in.)
140-D: 114.5 mm ± 5 mm (4.5 in. ± 3/16 in.)
140-F: 137.1 mm ± 5 mm (5.4 in. ± 3/16 in.)
Red/Yellow
Black
Red/Yellow
140-KN
140-CMN
2
140-KRY
140M-C, D, F
140M-C-DN66
140-CMN
140-CDN66
140M-C, D, F
140M-C-DRY66
140-CMN
140-CDRY66
3
4
5
Extension Shaft
Cut to required length for mounting depth (adapter-door):
140M-C: 117…338 mm (4.6 in.…13.3 in.)
140M-D: 126…347 mm (5.0 in.…13.7 in.)
140M-F: 149…369 mm (5.4 in.…14.5 in.)
140-CMN: 180…403 mm (7.1 in.…15.9 in.)
140M-C-DN66,
140M-C-DRY66,
140-CDN66,
140-CDRY66
140M-C-DS
Extension Shaft (Extended Length)
Cut to required length for mounting depth (adapter-door):
140M-C: 117…488 mm (4.6…19.2 in.)
140M-D: 126…497 mm (5.0…19.6 in.)
140M-F: 149…519 mm (5.4…20.4 in.)
140-CMN: 180…553 mm (7.1…21.8 in.)
140M-C-DN66,
140M-C-DRY66,
140-CDN66,
140-CDRY66
140M-C-DSL
140M-C, D, F
140M-C-DNC
Coupler
Included with Cat. Nos. 140M-C-DN66 and 140M-C-DRY66
6
7
Legend Plate
Marking: "Hauptschalter" and "Main Switch"
Marking: "Not-Aus" and "Emergency Off"
140-CDN66
140M-C-DFCN
140-CDRY66
140M-C-DFCRY
Locking Tag
Padlock attachment to the lockable handles
Up to three padlocks 4…8 mm (5/16 in.) shackle
140M-C-KN
140M-C-KRY
140M-F-KRY
140M-C-M3
Black
Handle
140M-C
198E-AYTG2
Red/Yellow
Handle
140M-C
198E-AYTJ2
IP65 Non-Metallic Enclosure
Knockouts for M20 and M25 fittings
Suitable for flexible cable with internal ground wire or conduit when externally grounded
around the outside of the enclosure (no UL approval)
1
8
9
10
11
Terminal Cover
For covering of unused commoning link terminals
IP2X finger protection
140M-C,
140M-D
140M-C-WS
140M-F
140M-F-WS
12
Screw Adapter
For screw arrangement of a Motor Protection Circuit Breaker
10 pcs/pkg
140M-C, D, F
140M-C-N45
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-29
02_140M_Circuit_Protectors_A.qxd
4/23/2008
11:06 AM
Page 2-30
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Accessories, Continued
Description
ECO Connecting Module — 12 A
For DOL and reversing starters
Eco-starters mount on single DIN Rail (140M on DIN Rail)
Electrical and mechanical interconnection of 140M MPCB and 100-K contactors
!
ECO Connecting Modules — 25 A
Eco-starters mount on single DIN Rail (140M on DIN Rail)
Electrical and mechanical interconnection of 140M MPCB and 100-C (with AC coils
or 24V DC electronic coils) contactors
1
Connecting Modules — 25 and 45 A
Contactor and MPCB MUST BE mounted separately on (2) DIN Rails
Electrical interconnection between 140M MPCB and 100-C contactors (with AC coils)
2
Coil Modules — 25 A and 45 A
y For use with Bulletin 103T/107T 3-component starters
3
Spacing Adapter
Required for Self-Protected combination motor controller (Type E) applications
of Bul. 140M-C, -D, and -F MPCBs
4
Compact Busbar Feeder Block
Supply of compact busbars
Increases terminal capacity
Compact Busbar Feeder Terminal
For supply of commoning links
Top feed — overlaps commoning link
Meets UL Type E spacing requirements
5
Three-Phase Compact Busbar for 25 A Motor Protection
Circuit Breakers — 63 A Max. Continuous Current
45 mm spacing
For use with front-mounted auxiliary contact
6
Three-Phase Compact Busbar for 25 A Motor Protection
Circuit Breakers — 63 A Max. Continuous Current
54 mm spacing
For use with side-mounted auxiliary contact
7
Three-Phase Compact Busbar for 25 A Motor Protection
Circuit Breakers — 63 A Max. Continuous Current
63 mm spacing
For use with side-mounted undervoltage trip and shunt trip
8
9
10
Cat. No.
140M-C to 100-K
140M-C-PEK12
140M-C to 100-C09…C23
140M-C-PEC23
140M-D to 100-C09…C23
140M-D-PEC23
140M-C to 100-C09…C23
140M-C-PNC23
140M-D to 100-C09…C23
140M-D-PNC23
140M-D to 100-C30…C37
140M-D-PNC37
140M-F to 100-C30…C37
140M-F-PNC37
140M-F to 100-C43
140M-F-PNC43
140M-C, -D to 100C09…C23
140M-C-PSC23
140M-D, -F to 100C30…C43
140M-F-PSC43
140M-C, -D
140M-C-TE1
140M-F
140M-F-TE
140M-C, -D
140M-C-WBE
140M-F
140M-F-WBE
140M-C, -D
140M-C-WTE
140M-F
140M-F-WTE
2 connections
3 connections
4 connections
140M-C-W452
140M-C, -D
140M-C-W453
140M-C-W454
5 connections
140M-C-W455
2 connections
140M-C-W542
3 connections
4 connections
140M-C, -D
140M-C-W543
140M-C-W544
5 connections
140M-C-W545
2 connections
140M-C-W632
3 connections
4 connections
140M-C, -D
5 connections
Jumper for 140M-D to 140M-C
Accommodates difference in depth from
Bul. 140M-D to 140M-C
54 mm spacing
Can be used with all other commoning links
2 connections
Three-Phase Compact Busbar for 45 A Motor Protection
Circuit Breakers — 115 A Max. Continuous Current
54 mm spacing
For use with front-mounted auxiliary contact
3 connections
Three-Phase Compact Busbar for 45 A Motor Protection
Circuit Breakers — 115 A Max. Continuous Current
63 mm spacing
For use with side-mounted auxiliary contact
For Use With
140M-C-W634
140M-C-W635
140M-D to 140M-C
2 connections
140M-C-WD542
140M-F-W542
140M-F
4 connections
140M-F-W543
140M-F-W544
2 connections
3 connections
140M-C-W633
140M-F-W632
140M-F
4 connections
140M-F-W633
140M-F-W634
11
DIN (#3) symmetrical Rail
35 mm x 7.5 mm x 1 m long
10 pcs/kg
140M-D
140M-F
199-DR1
12
DIN (#3) Symmetrical Rail
35 mm x 15 mm x 1 m long
Top Hat Rail (DIN #3 Symmetrical Rail)
5 pcs/kg
140M-C
140M-D
140M-F
140-CMN
1492-DR9
13
Notes: 1. See Bulletin 140U for Internal and External Accessories for Bulletin 140M-H, J, L and N frames.
2. Bulletin 140M-I frame Accessories such as auxiliaries, alarms, undervoltage and shunt trips are only available as factory installed modifications. See page 33.
Visit our website: www.ab.com/catalogs
2-30
Preferred availability cat. nos. are printed in bold
02_140M_Circuit_Protectors_A.qxd
4/23/2008
11:08 AM
Page 2-31
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Accessories, Continued
Description
For Use With
Pkg. Quantity
Terminal End Cover — 0.25 in.
Terminal End Cover — 0.41 in.
Cat. No.
140U-I-TC2
140M-I
1
!
140U-I-TC4
1
Terminal Shields (Plastic)
IP20 Ingress Protection
140M-I
1
140U-I-TS1
2
Padlockable Handle Lock Hasp
— Off only
Padlocking Hasp
Lock-OFF only
140M-I
End Cap Kit
Provides 3-phase connections for
terminal or bolt-on connections
Metric Hardware
140M-I
Phase Barriers
Provides additional phase
clearance when special
connections are required
140M-I
Terminal Lugs
Steel Terminal
Copper/Aluminum wire
#4-4/0 AWG
Terminal Lugs
Stainless Steel Terminal
Copper/Aluminum wire
#4-4/0 AWG
1
3
1
Operating Mechanism for
External Handles
140U-I-ECM
4
2
140U-I-PB
140U-I-TLS1
140M-I
3
5
6
140U-I-TLS2
Rotary Close Couple Handle
International
Black handle
Rotary Close Couple Handle
International
Red/Yellow handle
140U-I-PL
140U-I-RCB
140M-I
1
140U-I-RCR
140M-I
7
1
198-H2
8
9
External Handles
Black/Grey
IP66 (Type 3/3R/4/4X/12)
190-HM4
Red/Yellow
IP66 (Type 3/3R/4/4X/12)
190-HM4E
Black/Grey
IP55 (Type 1)
140M-I
10
1
190-HM1
Red/Yellow
IP55 (Type 1)
190-HM1E
Overload Pre-trip Auxiliary
Contact (AX)
Opens contactor coil circuit on
overload before MPCB trips
(Automatic reset)
140M-J, -L (MPCB only)
1
140U-J-ER1RX
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-31
02_140M_Circuit_Protectors_A.qxd
4/23/2008
11:09 AM
Page 2-32
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Accessories, Continued
Description
For Use With
Pkg. Quantity
Cat. No.
Extension Shafts
!
Standard Enclosure Working Depth [mm (in.)]
Minimum
203 (8)
Maximum
305 (12)
194R-R3
140M-I
1
Extended
1
Minimum
203 (8)
Maximum
508 (20)
Description
2
For Use With
Flex-Cable Operating
Mechanism
NEMA Type 1/3/12/4/4X
Flange-Mount Handle
Cat. No.
140U-I-FCX03
4 ft. (1.2 m) Cable
140U-I-FCX04
6 ft. (1.9 m) Cable
140U-I-FCX06
10 ft. (3.0 m) Cable
Flex-Cable Operating
Mechanism
Stainless Steel - Type 4/4X
Flange Mount Handle
140U-I-FCX10
140M-I
1
140U-I-FCS03
4 ft. (1.2 m) Cable
140U-I-FCS04
6 ft. (1.9 m) Cable
140U-I-FCS06
10 ft. (3.0 m) Cable
140U-I-FCS10
4
5
6
7
8
9
10
11
12
13
Visit our website: www.ab.com/catalogs
2-32
Pkg. Quantity
3 ft. (0.9 m) Cable
3 ft. (0.9 m) Cable
3
194R-R4
Preferred availability cat. nos. are printed in bold
02_140M_Circuit_Protectors_A.qxd
4/23/2008
11:09 AM
Page 2-33
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Factory Modifications
140M Factory Modifications (Open)
Note: For modifications add (option code *) for desired features to cat. no.
!
g
f
Aux / Trip Contacts - I, N
Miscellaneous
1st
Code
2nd
Code
Code
Description
Frame Size
KN
Black Lockable Knob
C, D, F, CMN
KY
Red/Yellow Lockable Knob
C, D, F, CMN
TE
Spacing Adapter for SelfProtected Starters (Type E)
C, D, F
MT
STD Bus Bar Mount, Top
C, D, F, H, CMN
F
2 N.O. + 2 N.C.
F9
2 N.O. + 2 N.C.
MU
STD Bus Bar Mount, Universal
J, K, L
N
1 N.O. (SC+OL) + 1 N.C. (SC)
N9
1 N.O. (SC+OL) + 1 N.C. (SC)
T
1 N.O. + 1 N.C. and 1 N.O. +
1 N.C. (SC+OL)
T9
1 N.O. + 1 N.C. and 1 N.O. +
1 N.C. (SC+OL)
g
Description
2nd
Code
Left Side
Description
1
Right Side
X
Placeholder
X
Placeholder
C
1 N.O. + 1 N.C.
C
1 N.O. + 1 N.C.
3
Description
Bottom Front
Right Side
X
Placeholder
X
Placeholder
h
A
1 N.C.
C
1 N.O. + 1 N.C.
UV and Shunt Trips - C, D, F
B
1 N.O.
D
2 N.O.
C
1 N.O. + 1 N.C.
E
2 N.C.
D
2 N.O.
K
1 N.C. (SC+OL) + 1 N.C. (SC)
E
2 N.C.
L
1 N.O. (SC+OL) + 1 N.O. (SC)
1st
Code
Description
G
Undervoltage Trip
2nd
Code
Left Side
4
Description
Voltage
J
24V AC, 60 Hz
K
24V AC, 50 Hz
R
1 N.C. + 1 N.O. (SC+OL)
M
1 N.C. (SC+OL) + 1 N.O. (SC)
S
1 N.O. + 1 N.O. (SC+OL)
N
1 N.O. (SC+OL) + 1 N.C. (SC)
D
120V AC, 60 Hz
1 N.O. (SC) + 1 N.C. (SC)
C
110V AC, 50 Hz
Q
g
Aux / Trip Contacts - CMN
1st
Code
Description
2nd
Code
Bottom Front
Description
Top Front‡
X
Placeholder
X
Placeholder
C
1 N.O. + 1 N.C.
K
1 N.C. (OL) + 1 N.C. (SC)
D
2 N.O.
L
1 N.O. (OL) + 1 NO (SC)
E
2 N.C.
M
1 N.C. (OL) + 1 N.O. (SC)
N
1 N.O. (OL) + 1 N.C. (SC)
P
Shunt Trip
‡Cannot be combined with option "h".
1st
Code
208V AC, 60 Hz
F
220…230V AC, 50 Hz
A
240V AC, 60 Hz
T
277V AC, 50 Hz
N
380…400V AC, 50 Hz
B
480V AC, 60 Hz and 415V AC,
50 Hz
VC
600V AC, 60 Hz
M
575V AC, 60 Hz and 500V AC,
50 Hz
ZR
9V DC
ZQ
12V DC
ZJ
24V DC
ZW
36V DC
ZY
48V DC
g
ZZ
60V DC
ZB
64V DC
ZG
72V DC
ZE
80V DC
2nd
Code
Bottom Front
X
H
Aux / Trip Contacts - H, J, L
Description
Placeholder
2
9 Only available on MCPs.
Aux / Trip Contacts - C, D, F
1st
Code
Description
Description
5
6
7
8
9
Right Side
X
Placeholder
C
1 N.O. + 1 N.C.
R7
1 N.O. + 1 N.C. (Overload
Function)
F9
2 N.O. + 2 N.C.
N9
1 N.O. (SC+OL) + 1 N.C. (SC)
T9
1 N.O. + 1 N.C. and 1 N.O. +
1 N.C. (SC+OL)
10
11
9 Only available on MCPs.
7 J- and L-Frame MPCB only.
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-33
02_140M_Circuit_Protectors_A.qxd
4/23/2008
11:09 AM
Page 2-34
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Factory Modifications, Continued
140M Factory Modifications (Open); Continued
Note: For modifications add (option code *) for desired features to cat. no.
!
1
1st
Code
2
h
h
UV and Shunt Trips - CMN
UV and Shunt Trips - I
2nd
Code
Description
Description
Top Front‡
G
1st
Code
Voltage
Undervoltage Trip
KJ
D
P
!
Shunt Trip
A
Description
2nd
Code
Left Front
UV Voltage
24V AC, 60 Hz and 24V AC,
50 Hz
120V AC, 60 Hz and 110V AC,
50 Hz
G
240V AC, 60 Hz and
220…230V AC, 50 Hz
Undervoltage Trip
J
24V AC
D
110…127V AC
A
208…240V AC
B
380…480V AC
Left Front
h
P
J
12…24V AC/DC
D
48…127V AC and 48…60V
DC
Shunt Trip
N
208…380V AC and
110…127V DC
B
415…600V AC and
220…250V DC
UV and Shunt Trips - H, J, L
4
1st
Code
Description
2nd
Code
Left Front
G
Undervoltage Trip
5
110…127V AC
A
208…240V AC
B
380…500V AC
Left Front
6
Shunt Trip
Description
12…60V AC/DC
110…240V AC/DC
B
380…600V AC
2nd
Code
Left Front
G
Undervoltage Trip
110…127V AC
A
208…240V AC
B
P
380…480V AC
Shunt Voltage
J
12…24V AC/DC
D
110…240V AC and
110…125V DC
N
380…440V AC and
220…250V DC
B
480…600V AC
Shunt Trip
5
24V AC
D
Left Front
7
Description
UV Voltage
J
Shunt Voltage
D
3
UV and Shunt Trips - N
1st
Code
525…600V AC
J
2
4
h
24V AC/DC
D
C
P
Description
UV Voltage
J
1
Shunt Voltage
‡ Cannot be combined with option "g".
3
Description
6
7
8
8
9
9
10
10
11
11
12
13
Visit our website: www.ab.com/catalogs
2-34
Preferred availability cat. nos. are printed in bold
02_140M_Circuit_Protectors_A.qxd
4/23/2008
11:10 AM
Page 2-35
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Specifications
IEC Performance Data
Cat. No. 140M-C2E-
!
1
2
A16
A25
A40
A63
B10
B16
B25
B40
B63
C10
C16
C20
C25
Rated Operational Current, Ie
[A]
0.16
0.25
0.4
0.63
1
1.6
2.5
4
6.3
10
16
20
25
Magnetic Release Current
[A]
2.1
3.3
5.2
8.2
13
21
33
52
82
130
208
260
325
0.12
0.18/0.25
0.37
0.25
0.37/0.55
0.75
1.1/1.5
0.25/0.37 0.55/0.75
1.1
1.5/2.2
Switching of Standard Three-Phase Motors
1
AC-2, AC-3
230/240V
[kW]
—
—
—
0.06/0.09
400/415V
[kW]
0.02
0.06
0.09
0.12/0.18
500V
[kW]
—
—
—
0.18
690V
!
[kW]
—
—
—
0.25
0.37/0.55 0.75/1.1
0.55/0.75 1.1/1.5
2.2
2.2
3.0/4.0 4.0/5.5
—
3.0/4.0 5.5/7.5 7.5/10
11
2.5/3.0 4.0/6.3 7.5/10
1.8
2.2/3.0
4.0
5.5/7.5
11/13
11
15
15/17
18.5/2
2
2
3
Back-Up Fuses
gG, gL, only if Icc≥Icu
3
4
230/240V
[A]
9
9
9
9
9
9
9
9
9
9
9
100
100
400/415V
[A]
9
9
9
9
9
9
9
9
9
9
80
100
100
440/460V
[A]
9
9
9
9
9
9
9
9
9
9
80
80
80
500V
[A]
9
9
9
9
9
9
9
9
9
80
80
80
80
690V
[A]
9
9
9
9
9
16
20
35
50
50
63
63
63
4
Ultimate Short Circuit Breaking Capacity
Icu
5
230/240V
[kA]
100
100
100
100
100
100
100
100
100
100
100
50
50
400/415V
[kA]
100
100
100
100
100
100
100
100
100
100
65
50
15
440/460V
[kA]
100
100
100
100
100
100
100
100
100
50
10
6
6
500V
[kA]
100
100
100
100
100
100
100
100
100
50
10
6
6
690V
[kA]
100
100
100
100
100
8
8
8
4
4
3
3
3
5
Rated Service Short Circuit Breaking Capacity
6
7
Ics
230/240V
[kA]
100
100
100
100
100
100
100
100
100
100
100
50
50
400/415V
[kA]
100
100
100
100
100
100
100
100
100
100
50
15
15
440/460V
[kA]
100
100
100
100
100
100
100
100
100
50
6
6
6
500V
[kA]
100
100
100
100
100
100
100
100
100
50
6
6
6
690V
[kA]
100
100
100
100
100
8
8
8
4
4
3
3
3
6
7
9 No back-up fuse required.
8
8
9
9
10
10
11
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-35
02_140M_Circuit_Protectors_A.qxd
4/23/2008
11:10 AM
Page 2-36
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Specifications, Continued
IEC Performance Data, Continued
!
Cat. No. 140M-D8E-
1
2
Cat. No. 140M-F8E-
B25
B40
B63
C10
C16
C20
C25
C10
C16
C20
C25
C32
Rated Operational Current, Ie
[A]
2.5
4.0
6.3
10
16
20
25
10
16
20
25
32
C45
45
Magnetic Release Current
[A]
33
52
82
130
208
260
325
130
208
260
325
416
585
Switching of Standard Three-Phase Motors
AC-2, AC-3
230/240V
[kW]
0.37
400/415V
[kW]
0.75
0.55/0.75 1.1/1.5
1.1/1.5
2.2
2.2
3.0/4.0
4.0/5.5
—
2.2
3.0/4.0
4.0/5.5
5.5/6.3
7.5
11/13
3.0/4.0
5.5/7.5
7.5/10
11
3.0/4.0
5.5/7.5
7.5/10
11
15
18.5/22
500V
[kW]
1.1
1.5/2.2
690V
[kW]
1.8
2.2/3.0
2.5/3.0
4.0/6.3
7.5/10
11
15
4.0/6.3
7.5/10
11
15
15/20
22/30
4.0
5.5/7.5
11/13
15/17
18.5/22 5.5/7.5
11/13
15/17
18.5/22
22/25
30/40
Back-Up Fuses
gG, gL, only if Icc≥Icu
3
4
230/240V
[A]
9
9
9
9
9
9
9
9
9
9
9
9
9
400/415V
[A]
9
9
9
9
9
100
100
80
100
100
100
125
125
440/460V
[A]
9
9
9
9
9
100
100
80
100
100
100
125
125
500V
[A]
9
9
9
9
80
100
100
80
100
100
100
125
125
690V
[A]
20
35
50
50
63
63
63
63
80
80
80
100
100
100
Ultimate Short Circuit Breaking Capacity
Icu
5
230/240V
[kA]
100
100
100
100
100
100
100
100
100
100
100
100
400/415V
[kA]
100
100
100
100
100
65
65
65
65
65
65
65
65
440/460V
[kA]
100
100
100
100
65
65
65
65
65
65
65
65
50
500V
[kA]
100
100
100
100
50
50
50
50
50
50
50
50
50
690V
[kA]
10
10
10
6
6
6
6
10
10
10
10
10
10
Rated Service Short Circuit Breaking Capacity
6
7
Ics
230/240V
[kA]
100
100
100
100
100
100
100
100
100
100
100
100
100
400/415V
[kA]
100
100
100
100
50
25
25
50
50
50
50
50
50
440/460V
[kA]
100
100
100
100
50
25
25
50
50
50
50
50
50
500V
[kA]
100
100
100
100
50
25
25
50
50
50
50
50
50
690V
[kA]
10
10
10
6
4
4
4
10
10
10
10
6
6
8
9
10
11
12
13
Visit our website: www.ab.com/catalogs
2-36
Preferred availability cat. nos. are printed in bold
02_140M_Circuit_Protectors_A.qxd
4/23/2008
11:10 AM
Page 2-37
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Specifications, Continued
IEC Performance Data, Continued
!
140-CMN-…
Cat. No.
Rated Operational Current, Ie [A]
-2500
25
-4000
40
-6300
63
-9000
90
350
560
890
1260
[kW]
5.5/7.5
10/11
13/20
22/25
Magnetic Release Current
[A]
Switching of Standard Three-Phase Motors
AC-2, AC-3
230/240V7
1
400/415V7
[kW]
7.5/13
15/22
25/32
37/45
500V7
[kW]
11/15
18.5/25
30/40
45/55
690V7
[kW]
15/22
25/30
37/55
63/75
2
Back-up fuses
gG, gL,, only if Icc ≥ Icu
230/240V
[A]
9
9
9
9
400/415V
[A]
160
160
160
160
500V
[A]
160
160
160
160
690V
[A]
160
160
160
160
3
Ultimate short-circuit breaking capacity Icu
230/240V
[kA]
100
100
100
100
400/415V
[kA]
65
65
65
50
500V
[kA]
50
30
30
25
690V
[kA]
15
8
8
6
4
Rated service short-circuit breaking capacity Ics
230/240V
[kA]
100
100
100
100
400/415V
[kA]
65
50
50
25
500V
[kA]
50
25
25
13
690V
[kA]
15
8
6
6
5
6
9 No back-up fuse required.
7 Power ratings: Preferred values according to IEC 60072-1.
7
8
9
10
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-37
02_140M_Circuit_Protectors_A.qxd
4/23/2008
11:10 AM
Page 2-38
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Specifications, Continued
IEC Performance Data, Continued
!
A16
A25
A40
Cat. No. 140M-C2NA63
B10
B16
B25
0.16
0.25
0.4
0.63
1
1.6
2.5
Magnetic Release Current
[A]
2.1
Switching of Standard Three-Phase Motors
AC-2, AC-3
3.3
5.2
8.2
13
21
32
Rated Operational Current, Ie
1
2
[A]
230/240V
[kW]
—
—
—
0.06/0.09
0.12
0.18/0.25
0.37
400/415V
[kW]
0.02
0.06
0.09
0.12/0.18
0.25
0.37/0.55
0.75
500V
[kW]
—
—
—
0.18
0.25/0.37
0.55/0.75
1.1
690V
[kW]
—
—
—
0.25
0.37/0.55
0.75/1.1
1.8
230/240V
[A]
9
9
9
9
9
9
9
400/415V
[A]
9
9
9
9
9
9
9
440/460V
[A]
9
9
9
9
9
9
9
500V
[A]
9
9
9
9
9
9
9
690V
[A]
9
9
9
9
9
16
20
Back-Up Fuses
gG, gL, only if Icc≥Icu9
3
Ultimate Short Circuit Breaking Capacity
4
5
Icu
230/240V
[kA]
100
100
100
100
100
100
100
400/415V
[kA]
100
100
100
100
100
100
100
440/460V
[kA]
100
100
100
100
100
100
100
500V
[kA]
100
100
100
100
100
100
100
690V
[kA]
100
100
100
100
100
10
8
Rated Service Short Circuit Breaking Capacity
Ics
6
7
230/240V
[kA]
100
100
100
100
100
100
100
400/415V
[kA]
100
100
100
100
100
100
100
440/460V
[kA]
100
100
100
100
100
100
100
500V
[kA]
100
100
100
100
100
100
100
690V
[kA]
100
100
100
100
100
8
8
9 No back-up fuse required.
8
9
10
11
12
13
Visit our website: www.ab.com/catalogs
2-38
Preferred availability cat. nos. are printed in bold
02_140M_Circuit_Protectors_A.qxd
4/23/2008
11:11 AM
Page 2-39
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Specifications, Continued
IEC Performance Data, Continued
Cat. No. 140M-D8NB25
B40
B63
C10
Cat. No. 140M-F8NC16
C25
C25
C32
C45
Rated Operational Current, Ie
[A]
2.5
4.0
6.3
10
16
25
25
32
45
Magnetic Release Current
[A]
32
52
82
130
208
325
325
416
585
Switching of Standard Three-Phase Motors
!
1
AC-2, AC-3
230/240V
[kW]
0.37
0.55/0.75
1.1/1.5
2.2
3.0/4.0
—
5.5/6.3
7.5
11/13
400/415V
[kW]
0.75
1.1/1.5
2.2
3.0/4.0
5.5/7.5
11
11
15
18.5/22
500V
[kW]
1.1
1.5/2.2
2.5/3.0
4.0/6.3
7.5/10
15
15
15/20
22/30
690V
[kW]
1.8
2.2/3.0
4.0
5.5/7.5
11/13
18.5/22
18.5/22
22/25
30/40
2
Back-Up Fuses
gG, gL, only if Icc≥Icu
230/240V
[A]
9
9
9
9
9
9
100
125
125
400/415V
[A]
9
9
9
9
9
100
100
125
125
440/460V
[A]
9
9
9
9
80
100
100
125
125
500V
[A]
9
9
9
9
80
80
100
125
125
690V
[A]
20
35
50
50
63
63
80
100
100
3
4
Ultimate Short Circuit Breaking Capacity
Icu
230/240V
[kA]
100
100
100
100
100
100
100
100
400/415V
[kA]
100
100
100
100
100
50
65
65
100
65
440/460V
[kA]
100
100
100
100
50
50
65
65
50
500V
[kA]
100
100
100
100
50
25
50
50
50
690V
[kA]
10
10
10
6
6
6
10
10
10
5
Rated Service Short Circuit Breaking Capacity
Ics
230/240V
[kA]
100
100
100
100
100
100
100
100
100
400/415V
[kA]
100
100
100
100
50
25
50
50
50
440/460V
[kA]
100
100
100
100
50
25
50
50
50
500V
[kA]
100
100
100
100
50
25
50
50
50
690V
[kA]
10
10
10
6
4
4
10
6
6
6
7
9 No back-up fuse required.
8
9
10
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-39
02_140M_Circuit_Protectors_A.qxd
4/23/2008
11:11 AM
Page 2-40
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Specifications, Continued
IEC Performance Data, Continued
!
Cat. No. 140M-D8T-
1
2
Cat. No. 140M-F8T-
C16
C20
C25
C32
Rated Operational Current, Ie
[A]
16
20
25
32
Magnetic Release Current
[A]
260
325
416
585
7.5
Switching of Standard Three-Phase Motors
AC-2, AC-3
230/240V 7
[kW]
3.0/4.0
4.0/5.5
5.5/6.3
400/415V 7
[kW]
5.5/7.5
7.5/10
11
15
500V 7
[kW]
7.5/10
11
15
15/20
690V 7
[kW]
11/13
15/17
18.5/22
22/25
Back-up fuses
gG, gL,, only if Icc ≥ Icu
3
4
5
230/240V
[A]
9
9
9
9
400/415V
[A]
80
100
100
125
440/460V
[A]
80
100
100
125
500V
[A]
80
80
100
125
690V
[A]
63
63
80
100
Ultimate short-circuit breaking capacity
Icu
230/240V
[kA]
100
100
100
100
400/415V
[kA]
65
65
65
65
440/460V
[kA]
65
65
65
65
500V
[kA]
50
25
50
50
690V
[kA]
6
6
10
10
Rated service short-circuit breaking capacity Ics
6
7
Ics
230/240V
[kA]
100
100
100
100
400/415V
[kA]
25
25
50
50
440/460V
[kA]
25
25
50
50
500V
[kA]
25
25
50
50
690V
[kA]
4
4
6
6
9 No back-up fuse required.
7 Consult your local Rockwell Automation sales office or Allen-Bradley distributor.
8
9
10
11
12
13
Visit our website: www.ab.com/catalogs
2-40
Preferred availability cat. nos. are printed in bold
02_140M_Circuit_Protectors_A.qxd
4/23/2008
11:11 AM
Page 2-41
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Specifications, Continued
IEC Performance Data, Continued
Cat. No. 140M-C2TA16
A25
A40
A63
B10
B16
B25
B40
B63
C10
C16
Rated Operational Current, Ie
[A]
0.16
0.25
0.40
0.63
1.0
1.6
2.5
4.0
6.3
10
16
Magnetic Release Current
[A]
3.2
5.2
8.2
13
21
32
52
82
130
208
260
Switching of Standard Three-Phase Motors
!
1
AC-2, AC-3
230/240V
[kW]
—
—
—
0.06/0.09
0.12
0.18/0.25
0.37
0.55/0.75
1.1/1.5
2.2
3.0/4.0
400/415V
[kW]
0.02
0.06
0.09
0.12/0.18
0.25
0.37/0.55
0.75
1.1/1.5
2.2
3.0/4.0
5.5/7.5
500V
[kW]
—
—
—
0.18
0.25/0.37 0.55/0.75
1.1
1.5/2.2
2.5/3.0
4.0/6.3
7.5/10
690V
[kW]
—
—
—
0.25
0.37/0.55 0.75/1.1
1.8
2.2/3.0
4.0
5.5/7.5
11/13
230/240V
[A]
9
9
9
9
9
9
9
9
9
9
9
400/415V
[A]
9
9
9
9
9
9
9
9
9
9
80
440/460V
[A]
9
9
9
9
9
9
9
9
9
9
80
500V
[A]
9
9
9
9
9
9
9
9
9
80
80
690V
[A]
9
9
9
9
9
16
20
35
50
50
63
2
Back-Up Fuses
gG, gL, only if Icc≥Icu
Ultimate Short Circuit Breaking Capacity
3
4
Icu
230/240V
[kA]
100
100
100
100
100
100
100
100
100
100
100
400/415V
[kA]
100
100
100
100
100
100
100
100
100
100
50
440/460V
[kA]
100
100
100
100
100
100
100
100
100
50
10
500V
[kA]
100
100
100
100
100
100
100
100
100
50
10
690V
[kA]
100
100
100
100
100
8
8
8
4
4
3
5
Rated Service Short Circuit Breaking Capacity
Ics
230/240V
[kA]
100
100
100
100
100
100
100
100
100
100
100
400/415V
[kA]
100
100
100
100
100
100
100
100
100
100
15
440/460V
[kA]
100
100
100
100
100
100
100
100
100
50
6
500V
[kA]
100
100
100
100
100
100
100
100
100
50
6
690V
[kA]
100
100
100
100
100
8
8
8
4
4
3
6
7
9 No back-up fuse required.
8
9
10
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-41
02_140M_Circuit_Protectors_A.qxd
4/23/2008
11:12 AM
Page 2-42
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Specifications, Continued
General Data
Cat. No.
!
140M-C
140M-D
140M-F
140-CMN
Rated Insulation Voltage Ui
1
IEC, SEV, VDE 0660
[V]
690
690
UL, CSA
[V]
600
600
Rated Impulse Withstand Voltage Uimp
Pollution degree
Main circuits Uimp /Overvoltage Category
Auxiliary circuits Uimp /Overvoltage Category
Rated Frequency
2
[Hz]
3
3
6 kV/III
6 kV/III
6 kV/III
6 kV/III
50/60
40…60
Utilization Category
IEC 60947-2 (Circuit breaker)
A
A
IEC 60947-4-1 (Motor starter)
AC-3
AC-3
Life Span
3
Mechanical
Electrical (Ie max.)
Switching Frequency
[operations]
100 000
[operations]
100 000
[operations/h]
30 000
30 000
30 000
10 000 (up to 63 A)
5 000 (up to 90 A)
max. 25 (motor starts)
max. 20
-40 … +80
-25… +80
Ambient Temperature
4
Storage
[°C]
Operation
[°C]
-25… +60
Resistance to Climatic Change
IEC 68-2
Moisture/heat resistance
5
Moisture/change resistance
Site Altitude
23 °C, 83%/40 °C, 92%, 50 cycles
[m]
to 2000 N.N.
Protection Class
Resistance to Shock
6
IP20, when wired
[g]
30, 11 ms
Resistance to Vibration
Frequency range
in all directions
C IV (acc. to IEC 68)
40 °C, 92% relative humidity, 56 days
30, 11 ms
IEC 68-2
[Hz]
10…150
[g]
under testing
Rated Thermal Current Ith
7
IEC, SEV, VDE 0660
up to 40 °C ambient temperature
[A]
0.1…25
1.6…25
6.3…45
up to 60 °C ambient temperature
[A]
0.1…25
1.6…25
6.3…45
16… 90
Rated Supply Current Ie
[A]
0.1…25
1.6…25
6.3…45
16… 90
13
7
6
4
Number of setting ranges
8
9
Dependence on Temperature
40 °C
[A]
no reduction
50 °C
[A]
no reduction
60 °C
[A]
no reduction
70 °C
[A]
15 % current reduction of the upper rated current Ie
Overload Protection
IEC 60947-4-1 Motor protection
(except Cat. Nos. 140M-C2N, 140M-D8N, 140M-F8N)
Characteristics
Ambient Temperature Compensation
10
[°C]
IEC 60947-4-1
Motor protection
-20 …+60
Phase-loss Protection
Differential release
Trip class
11
16… 90
Magnetic Release
Release current
10 (except Cat. Nos. 140M-C2N, 140M-D8N, 140M-F8N)
fixed setting
10
fixed setting
13 x Ie max. (for 140M-C2E, 140M-D8E, 140M-F8E, 140MC2N, 140M-D8N, 140M-F8N)
16…20 x Ie max. (for 140M-C2T, 140M-D8T, 140M-F8T)
Ie max. = maximum values of setting ranges
fixed setting
14 x Ie max.
Total Power loss Pv
Circuit Breaker at rated load operating temperature
12
Main Circuit Breaker Application
[W]
6…8
6…8
13
Visit our website: www.ab.com/catalogs
2-42
9…16
33
Usable as main circuit breaker according to IEC 204 with corresponding accessories
Preferred availability cat. nos. are printed in bold
02_140M_Circuit_Protectors_A.qxd
4/23/2008
11:12 AM
Page 2-43
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Specifications, Continued
General Data, Continued
Cat. No.
140M-C…
140M-D…
Conformity to Standards
140M-F…
140-CMN
IEC 60947-1; -2; -4-1;
EN 60947-1; -2; -4-1;
UL 508; CSA 22.2, No. 14
IEC 60947-1; -2; -4-1;
EN 60947-1; -2; -4-1;
UL 508; CSA 22.2, No. 14
CE, UL, CSA
CE, UL, CSA
Approvals
1
Terminal Parts
Type of terminals
Screwdriver
Pozidriv No. 2/Blade No. 3
Pozidriv No. 2/Blade No. 3
1. conductor
2. conductor
[mm2 ]/[AWG]
[mm2 ]/[AWG]
1…4/No. 16…10
1…4/No. 16…10
2.5…16/No. 14…4
2.5…10/No. 14…4
2.5…35
1. conductor
2. conductor
[mm2 ]/[AWG]
[mm2 ]/[AWG]
1.5…6/No. 16…8
1.5…6/No. 16…8
2.5…16/No. 14…4
2.5…10/No. 14…4
4…50 / 12…2
1. conductor
2. conductor
[mm2 ]/[AWG]
[mm2 ]/[AWG]
1…6/No. 16…10
1…6/No. 16…10
2.5…25/No. 14…4
2.5…16/No. 14…4
4…50 / 12…2
2…2.5/18…22
3…3.5/27…30
6…10/55…90
Tightening torque
!
[Nm]/[lb•in]
2
3
Accessories for Bulletin 140M Motor Protection Circuit Breakers
Auxiliary Contact Blocks for
Front Mounting
Cat. No. 140M-C-AFA…, 140M-C-AFAR…
Auxiliary Contact Blocks for
Right-Side Mounting
Cat. No. 140M-C-ASA…, 140M-C-ASAR…
[A]
[A]
5
4
10
6
(UL/CSA Standards)
AC
DC
B 300
Q 300
B 600
Q 600
Back-Up Fuses gG, gL
[A]
10
10
Rated Thermal Current Ith
at 40 °C ambient
temperature
at 60 °C ambient
temperature
4
5
Contact Class Coordination
According to NEMA
Rated Supply Current
6
[V]
24
120
240
24
120
240
415
690
AC-15
[A]
4
3
1.5
6
5
3
2
0.7
DC-13
[V]
24
120
240
24
120
240
415
[A]
2
0.5
0.25
2
0.5
0.25
0.15
7
Terminal Parts
Type of terminals
Screwdriver
Pozidriv No. 2/Blade No. 3
1. conductor
2. conductor
[mm2]/[AWG]
[mm2]/[AWG]
0.5…1.5/18…14
0.75…1.5/18…14
0.5…2.5/18…14
0.75…2.5/18…14
1. conductor
2. conductor
[mm2]/[AWG]
[mm2]/[AWG]
0.75…1.5/18…14
0.75…1.5/18…14
0.75…2.5/18…14
0.75…2.5/18…14
1. conductor
2. conductor
[mm2]/[AWG]
[mm2]/[AWG]
0.75…1.5/18…14
0.75…1.5/18…14
0.75…2.5/18…14
0.75…2.5/18…14
[N•m]/[lb•in]
1.2…1.5/10.6…13
1.2…1.5/10.6…13
Tightening torque
8
9
10
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-43
02_140M_Circuit_Protectors_A.qxd
4/23/2008
11:12 AM
Page 2-44
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Specifications, Continued
Accessories for Bulletin 140M Motor Protection Circuit Breakers, Continued
!
1
Actuating Voltage
Pull-in
Drop-out
Rated Control Voltage
min.
max.
Undervoltage Trip
for Left-Side Mounting
Cat. No. 140M-C-UX…
Undervoltage Trip
with 2 Auxiliary Contacts
for Left-Side Mounting
Cat. No. 140M-C-UC…
0.85…1.1 x Us
0.7…0.35 x Us
0.85…1.1 x Us
0.7…0.35 x Us
0.7…1.1 x Us
21V 50 Hz, 24V 60 Hz
600V 50 Hz
21V 50 Hz, 24V 60 Hz
600V 50 Hz
21V 50 Hz, 24V 60 Hz
600V 50 Hz
On-Time
2
Coil Rating
Pull-in
Hold
Shunt Trip
for Left-Side Mounting
Cat. No. 140M-C-SN…
100%
100%
100%
8.5 VA, 6 W
3 VA, 1.2 W
8.5 VA, 6 W
3 VA, 1.2 W
8.5 VA, 6 W
3 VA, 1.2 W
Terminal Parts
Type of terminals
3
Screwdriver
4
Pozidriv No. 2/Blade No. 3
1. conductor
2. conductor
[mm2]/[AWG]
[mm2]/[AWG]
0.5…2.5/No. 18…14
0.75…2.5/No. 18…14
1. conductor
2. conductor
[mm2]/[AWG]
[mm2]/[AWG]
0.75…2.5/No. 18…14
0.75…2.5/No. 18…14
1. conductor
2. conductor
[mm2]/[AWG]
[mm2]/[AWG]
0.75…2.5/No. 18…14
0.75…2.5/No. 18…14
[N•m]/[lb•in]
1.25…1.5/10.6…13.3
Tightening torque
5
Commoning Link Feeder Terminal 140M-C-WTE
Rated Thermal Current Ith
at 60 °C ambient
temperature
6
[A]
140M-F-WTE
140M-C-W
140M-F-W
64
120
64
120
1. conductor
[mm2]/[AWG]
1.5…16
4…50/12…110
⎯
⎯
1. conductor
[mm2]/[AWG]
1.5…25/No. 14…4
2.5…50/12…110
⎯
⎯
1. conductor
[mm2]/[AWG]
1.5…25/No. 14…4
⎯
⎯
[N•m]/[lb•in]
3/27
⎯
⎯
Tightening torque
5…6/45…54
7
8
9
10
11
12
13
Visit our website: www.ab.com/catalogs
2-44
Commoning Link
140M-C-WTE
Preferred availability cat. nos. are printed in bold
02_140M_Circuit_Protectors_A.qxd
4/23/2008
11:12 AM
Page 2-45
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Specifications, Continued
Weights
Description
Motor Protection Circuit Breakers
Weight [g]
Cat.No.
317
140M-C2E-…
373
140M-D8E-…
782
140M-F8E-…
315
140M-C2N-…
365
140M-D8N-…
782
140M-F8N-…
315
140M-C2T-…
365
140M-D8T-…
782
140M-F8T-…
1845
140-CMN-…
!
1
2
140M-C-AFA10
140M-C-AFA01
10
3
140M-C-AFA11
140M-C-AFA20
Auxiliary Contacts
140M-C-ASA…
140M-C-AFAR10A…
15
140M-C-ASAR…M…
4
140M-C-ASAM11
31
Undervoltage Trip
140-CA…
108
140M-C-UX…
110
140M-C-SN…
116
140M-C-UC…
94
140-CUV…
Trip Contact Blocks
31
140-CT…
Shunt Trip
94
140-CRT…
Weight [g]
Cat.No.
`
Anti-Tamper Cover
2
140M-C-CA
5
Locking Tag
30
Door Coupling Handle
123
Extension Shaft
46
140M-C-DS
Legend Plate
4
140M-C-DFC…
Commoning Links
172
6
140M-C-KN
Lockable Twist Knob
Feeder Terminal
5
140M-C-KRY
7
140M-C-M3
140M-C-DN66
140M-C-NRY66
8
140M-C-WT
140M-F-WT
47
140M-C-W452
80
140M-C-W453
104
140M-C-W454
132
140M-C-W455
52
140M-C-W542
86
140M-C-W543
118
140M-C-W544
154
140M-C-W545
56
140M-C-W632
92
140M-C-W633
134
140M-C-W634
170
140M-C-W635
9
10
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-45
02_140M_Circuit_Protectors_A.qxd
4/23/2008
11:12 AM
Page 2-46
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Specifications, Continued
Accessories for Bulletin 140-CMN Circuit Breakers
!
Cat. No. 140-CT
Trip Contact Block for Flush Mounting on Cat.
No. 140-CMN Circuit Breakers
1
2
Rated Thermal
Current Ith
up to 40 °C ambient
temperature
up to 60 °C ambient
temperature
NEMA contact class
(UL/CSA-Approval)
Cat. No. 140-CRT, 140-CUV
Undervoltage Trip and Shunt Trip for Flush Mounting on
Cat. No. 140-CMN Circuit Breakers
2
2
[A]
[A]
10
6
AC
DC
B 600 Standard Pilot Duty
R 300 Light Pilot Duty
Make/Break max. voltage
432 VA72 VA480 V
28 VA28 VA250 V
16 A
16 A
Back-Up Fuse gG, gL
Rated Current Ie
3
AC-15:
[V]
[A]
230
3
400
2.5
500
1.5
690
0.75
DC-13:
[V]
[A]
24
2
48
0.6
110
0.2
230
0.1
440
0.04
AC-14:
24
1.5
110
1.5
230
1.0
400
1.0
DC 13:
24
1.5
48
0.5
60
0.4
110
0.2
500
0.75
Terminals
4
Screwdriver
5
1.conduct
or
2.conduct
or
[mm2]/[AWG]
[mm2]/[AWG]
0.75… 2.5/No. 18… 14
0.75… 2.5/No. 18… 14
0.75… 2.5/No. 18… 14
0.75… 2.5/No. 18… 14
1.conduct
or
2.conduct
or
[mm2]/[AWG]
[mm2]/[AWG]
0.75… 2.5/No. 18… 14
0.75… 2.5/No. 18… 14
0.75… 2.5/No. 18… 14
0.75… 2.5/No. 18… 14
[N•m]/[lb•in]
1… 1.5/8.8… 10.3
1… 1.5/8.8… 10.3
Tightening torque
6
Cat. No. 140-CUV…
Undervoltage Trip Unit for
Right-Side Mounting on
Cat. No. 140-CMN Circuit
Breakers
Cat. No. 140-CRT...
Shunt Trip for Flush Mounting
on
Cat. No. 140-CMN Circuit
Breakers
Pick-up
0.8… 1.1 x Us
0.7… 1.1 x Us
Drop-out
0.7… 0.35 x Us
⎯
Duty cycle
100 % ED
100 % ED
min.
12 V 50 Hz/14 V 60 Hz
12 V 50 Hz/14 V 60 Hz
max.
600 V 50 Hz
600 V 50 Hz
[VA/W]
[VA/W]
11 / 8
4/1
12 / 7
6/2
Fine-stranded
[mm2]
2 x 0.75…2.5
2 x 0.75…2.5
Coarse-stranded
[mm2]
2 x 0.75…2.5
2 x 0.75…2.5
1… 1.5
1… 1.5
Coarse-stranded
[AWG]
No. 18…. 14
No. 18…. 12
[lb•in]
8.8… 10.3
8.8… 10.3
7
Operating Voltage
8
Control Voltage
9
Coil Performance
Pick-up
Drop-out
10
11
Terminals
Terminal type
Tightening torque
Tightening torque
[Nm]
12
13
Visit our website: www.ab.com/catalogs
2-46
Preferred availability cat. nos. are printed in bold
02_140M_Circuit_Protectors_A.qxd
4/23/2008
11:12 AM
Page 2-47
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Specifications, Continued
Cut-off current
!
asymmetrical
symmetrical
1
The Bulletin 140-M limits solid short-circuit current Icc (prospective short-circuit current). ID is the maximum cut-off current (highest
instantaneous value of the limited short-circuit current). This value is indicated in the following diagrams as a function of the progressive
system short-circuit current.
2
Bulletin 140M-C Circuit Breaker
Maximum cut-off current
Rated operating voltage 415V
Maximum forward energy
Rated operating voltage 415V
3
4
5
6
7
Bulletin 140M-D Circuit Breaker
Maximum cut-off current
Rated operating voltage 415V
8
Maximum cut-off current
Rated operating voltage 415V
9
max. forward energy
max. cut-off current ID [kA]
10
11
12
Prospective short-circuit current Icc [kA]
Prospective short-circuit current Icc [kA]
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-47
02_140M_Circuit_Protectors_A.qxd
4/23/2008
11:12 AM
Page 2-48
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Specifications, Continued
Bulletin 140M-F Circuit Breaker
!
Maximum cut-off current
Rated operating voltage 415V
Maximum cut-off current
Rated operating voltage 415V
3
max. forward energy
2
max. cut-off current ID [kA]
1
4
Prospective short-circuit current Icc [kA]
Prospective short-circuit current Icc [kA]
5
Time-Current Characteristic
Bulletin 140M-C, -D, -F Motor Protection Circuit Breakers
Bulletin 140-CMN Motor Protector
10 000
1h
6
1 000
100
1
7
Release Time [s]
8
10
1
2
0.1
0.01
9
0.001
0.8 1
2
4
6
10
20
40 60
100
Multiple of the set current IeF
10
1) Thermal Release Trip Current
The adjustable current-dependent delayed bimetal release protects motors against overload. The curve shows the mean operating current at
an ambient temperature of 20 °C starting from the cold state. Careful testing and setting ensures effective motor protection even in the case
of single-phasing. The overload characteristic is also valid for transformer protection.
11
2) Magnetic Release Trip Current
The instantaneous magnetic trip has a fixed operating current setting. This corresponds to 13 times the maximum value of setting range.
(Transformer protection up to 20 x Ie max.) At a lower setting it is correspondingly higher.
12
13
Current Setting IeF
The overload trip corresponds to a thermal overload relay in a motor starter conforming to IEC947-4-1. If a different value is prescribed (e.g.,
reduced Ie for cooling medium having a temperature higher than 40 °C or a place of installation higher than 2000 m above sea level), the
setting current is equal to the reduced rated current Ie of the motor.
Visit our website: www.ab.com/catalogs
2-48
Preferred availability cat. nos. are printed in bold
02_140M_Circuit_Protectors_A.qxd
4/23/2008
11:12 AM
Page 2-49
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Approximate Dimensions
Cat. No. 140M-C, -D, -F
!
Dimensions are shown in millimeters. Dimensions are not intended to be used for manufacturing purposes.
Cat. No. 140M-C2…
Cat. No. 140M-D8…
65
1
2
45
92
90
91
45
92
45
45
4.5
4.5
90
91
45
5
5
45
54.9
24.8
18
45
9
4.5
§
44
62
8
24.8
18
70
45
§
9
4.5
54
3
8
72
80
4
55
Cat. No. 140M-F8…
Mounting on 35 mm DIN Rail
§ Auxiliary contact (side mounted)
Undervoltage/shunt trip
Auxiliary contact (front mounted)
5
45
111.4
55.7
4.5
6
18
§
29.4
4.5
7
91
9
54
8
102
110
54.9
8
64.9
43.9
53.9
44.7
42.4
34.8
42.4
13.9
10
23.9
5 L3
5
3 L2
55
5 L3
3 L2
1 L1
9
10
3 L2
5 L3
5 L3
3 L2
1 L1
(10)
(10)
1 L1
Cat. No. 140M-C-TE1 Type E adapter on Cat. No. 140M-C2E…
(55)
44.9
5 L3
5 L3
3 L2
3 L2
1 L1
1 L1
(55)
45
44.9
44.9
5
5 L3
5 L3
3 L2
3 L2
1 L1
1 L1
1 L1
10
24.8
55
44.7
11
12
Cat. No. 140M-C-TE1 Type E adapter on Cat. No. 140M-D8E…
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-49
02_140M_Circuit_Protectors_A.qxd
4/23/2008
11:12 AM
Page 2-50
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Approximate Dimensions, Continued
Dimensions are shown in millimeters. Dimensions are not intended to be used for manufacturing purposes.
°
90
90
30°
0°
°
12
d
!
d
1
2
Mounting position/safety clearance of Cat. No. 140M-C…, 140M-D…, 140M-F…
3
4
4.5
min. 100
1.5...5
5
3.5
35...45
b
53.5
6
53.5
140M-C-DS
140M-C-DSL
a
7
c1
+ 5 mm
4...8
+ 5 mm
c2
4.5
8
9
2.4
140M-C-D…66
10
With Cat. No. 140-M-C-DS Shaft
11
With Cat. No. 140-M-C-DSL Shaft
Cat. No.
a
b
c1
c2
d
Cat. No.
a
b
c1
c2
d
140M-C
117…338
105.5 ±5
49.5
40.5
25
140M-C
117…438
105.5 ±5
49.5
40.5
25
140M-D
126…347
114.5 ±5
49.5
40.5
25
140M-D
126…497
114.5 ±5
49.5
40.5
25
140M-F
148.6…369.6
137.1 ±5
59.35
50.35
30
140M-F
148.6…519
137.1 ±5
59.35
50.35
30
12
13
Visit our website: www.ab.com/catalogs
2-50
Preferred availability cat. nos. are printed in bold
02_140M_Circuit_Protectors_A.qxd
4/23/2008
11:12 AM
Page 2-51
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Approximate Dimensions, Continued
Dimensions are shown in millimeters (inches). Dimensions are not intended to be used for manufacturing purposes.
!
Cat. No. 198E…
1
2
3
4
5
6
198E-AYT…
7
8
9
10
140M-C-WB
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-51
02_140M_Circuit_Protectors_A.qxd
4/23/2008
11:12 AM
Page 2-52
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Approximate Dimensions, Continued
Dimensions are shown in millimeters (inches). Dimensions are not intended to be used for manufacturing purposes.
!
Cat. No. 140-CMN…
1
2
3
4
5
140-CMN
70
6
90
°
90
°
°
90
30°
70
7
8
Mounting position/safety clearance of Cat. No. 140-CMN
9
140-CD…
10
Note: See Bulletin 140U-H, J, L and N for dimensions of 140M-H, J, L and N frames.
11
12
13
Visit our website: www.ab.com/catalogs
2-52
Preferred availability cat. nos. are printed in bold
02_140M_Circuit_Protectors_A.qxd
4/23/2008
11:13 AM
Page 2-53
Bulletin 140M
Motor Protection Circuit Breakers and Motor Circuit Protectors
Approximate Dimensions, Continued
Dimensions are shown in millimeters (inches). Dimensions are not intended to be used for manufacturing purposes.
Cat. Nos. 140M-H, -I, -J, -L, -N
A
!
G
C
E
D
1
F
B
2
3
4
5
E
7
H
H
6
E
E
E
8
E
A
B
C
D
E
F
G
H
H-Frame
77
(3)
140
(5-1/2)
88
(3-1/2)
75
(3)
25.4
(1)
96.8
(3-13/16)
24.6
(31/32)
22.4
(7/8)
I-Frame
105
(4-1/8)
152
(6)
105
(4-1/8)
88
(3-1/2)
35
(1-3/8)
114
(4-1/2)
19
(3/4)
40
(1-9/10)
J-Frame
105
(4-1/8)
178
(7)
113
(4-29/64)
88
(3-1/2)
35
(1-3/8)
139.7
(5-1/2)
19.8
(25/32)
20.6
(13/16)
L-Frame
140
(5-1/2)
258
(10-5/32)
138
(5-7/16)
110
(4-21/64)
43.7
(1-23/32)
214.4
(8-7/16)
21.3
(27/32)
24.7
(31/32)
N-Frame
210
(8-17/64)
407
(16-1/64)
183
(7-13/64)
140
(5-1/2)
69.9
(2-3/4)
374.7
(14-3/4)
16
(5/8)
29.5
(1-5/32)
9
10
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-53
01_140U_100A_G_Frame.qxd
4/23/2008
11:53 AM
Page 2-54
Bulletin 140U
Molded Case Circuit Breakers
Product Overview
!
!
1
2
3
Bulletin 140U Molded Case Circuit Breakers
Table of Contents
y 15…1200 A Molded Case Circuit Breakers
− Thermal-Magnetic 15…800 A
− Electronic 70…1200 A
y LS — Long Time/Short Time
y LSI — Long Time/Short Time/High Instantaneous
y LSG — Long Time/Short Time/Ground Fault
y LSIG — Long Time/Short Time/High Instantaneous/Ground
Fault
− Molded Case Switches 125…1200 A
y Factory- or field-installed accessories
y Flex cable operating mechanisms
y Rotary variable-depth operating mechanisms
y High interrupting ratings in compact dimensions
y Globally rated and approved product line for worldwide application
Product Selection —
100 A, G-Frame.......... 2-57
Product Selection —
125 A, H-Frame.......... 2-60
Product Selection —
250 A, J-Frame........... 2-69
Product Selection —
400 A, K-Frame .......... 2-74
Product Selection —
600 A, L-Frame........... 2-79
Product Selection —
800 A, M-Frame ......... 2-84
Product Selection —
1200 A, N-Frame ....... 2-88
Certifications
Standards Compliance
UL Listed
CSA Certified
CE Marked
KEMA-KEUR
UL 489
CSA 22.2, No. 5
EN/IEC 60947-2
4
Product Line Overview
5
6
7
8
G-Frame
H-Frame
J-Frame
K-Frame
L-Frame
M-Frame
Max. Current In
Frame Reference
100 A
125 A
250 A
400 A
600 A
800 A
1200 A
Current Range
15…100 A
15…125 A
70…250 A
100…400 A
300…600 A
300…800 A
600…1200 A
9
9
9
9
9
9
—
LS
—
—
9
9
9
9
9
LSI
—
—
9
9
9
9
9
LSG
—
—
9
9
9
9
9
LSIG
—
—
9
9
9
9
9
Thermal Magnetic
N-Frame
Electronic:
Interrupting Ratings:
9
10
11
12
13
380…415V (Icu)
14
22
480V
14
22
600V
—
690V (Icu)
—
25
25
40
35
18
65
22
3
70
25
40
70
100
40
65
100
45
70
100
50
70
50
70
100
100 25
35
65
100
35
65
100
35
65
100
50
65
50
65
100
35
18
18
25
35
25
35
50
25
35
50
25
35
25
35
50
6
6
7
12
10
13
18
20
25
15
20
25
20
25
30
25
4
6
Molded Case Switches
9
9
9
9
9
9
9
Flex Cable Operators
9
9
9
9
9
9
9
Rotary Operators
9
9
9
9
9
9
9
Internal Control
Modules
(Field installed)
9
9
9
9
9
9
9
UL 489
9
9
9
9
9
9
9
UL File E197878,
Guide No. DIV Q
9
9
9
9
9
9
9
CSA 22.2, No. 5
9
9
9
9
9
9
9
CSA File Nos.
216034, 216035,
219884 Class No.
1432-01
9
9
9
9
9
9
9
IEC 60947-2
9
9
9
—
9
9
9
CE
9
9
9
—
9
9
9
KEMA-KEUR
9
9
9
9
9
9
9
Standards Compliance
Visit our website: www.ab.com/catalogs
2-54
Preferred availability cat. nos. are printed in bold
01_140U_100A_G_Frame.qxd
4/23/2008
11:53 AM
Page 2-55
Bulletin 140U
Molded Case Circuit Breakers
Catalog Number Explanation
Examples given in this section are for reference purposes. This basic explanation should not be used for product selection; not all
combinations will produce a valid cat. no. Refer to the tables on the following pages for descriptions of options.
!
Complete Circuit Breaker Assemblies
140U –
H
6
C
3
– C50 –
H
b
c
d
e
f
g
a
1
h
a
d
g
Bulletin No.
Protection Type
Internal Control Modules
Code
Description
Code
Description
Code
140U
Molded Case Circuit Breaker
C
Fixed Thermal/Fixed Magnetic
A
1 Auxiliary contact
D
Fixed Thermal/Adjust Magnetic
B
2 Auxiliary contacts
2
Description
b
E
Adjust Thermal/Fixed Magnetic
D
1 Alarm contact
Frame/Rating
F
Adjust Thermal/Adjust Magnetic
F
1 Auxiliary + 1 Alarm contact
G
Electronic (LSG — Long, short,
ground fault)
G
Undervoltage release only
H
Electronic (LSI — Long, short,
high instant)
I
Electronic (LSIG — Long, short,
high instant, ground fault)
Code
Description
H
125 A
J
250 A
K
400 A
L
600 A
Description
H
1 Auxiliary contact + undervoltage release
J
2 Auxiliary contacts + undervoltage
release
L
e
1 Auxiliary + 1 Alarm contact +
undervoltage release
N
1 Alarm contact + undervoltage release
800 A
L
Electronic (LS — Long and Short time)
N
1200 A
S
Molded Case Switch (Isolator)
Interrupting Rating/Breaking Capacity
(based on Ic at 480V)
Shunt trip only
Control Module Combinations
Code
M
c
P
Poles
Q
1 Auxiliary contact + shunt trip
Code
Description
R
2 Auxiliary contacts + shunt trip
Code
Description
1
1 poles
2
20…29 kA
T
1 Auxiliary + 1 Alarm contact + shunt trip
2
2 poles
3
30…39 kA
V
1 Alarm contact + shunt trip
3
3 poles
5
50…59 kA
6
60…69 kA
8
80…89 kA
0
≥100 kA
f
Current Range
Code
Description
C
10 rr. A
D
100 rr0 A
E
1000 rr00 A
3
4
5
6
h
Voltage Code
7
See the following pages for
voltage code descriptions:
All frame sizes
Page 2-92
8
9
10
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-55
01_140U_100A_G_Frame.qxd
4/23/2008
11:53 AM
Page 2-56
Bulletin 140U
Molded Case Circuit Breakers
Catalog Number Explanation, Continued
Examples given in this section are for reference purposes. This basic explanation should not be used for product selection; not all
combinations will produce a valid cat. no. Refer to the tables on the following pages for descriptions of options.
!
!
Frames
140U –
1
2
3
4
a
J
3
X
3
b
c
d
e
a
c
d
Bulletin No.
Interrupting Rating/Breaking Capacity
(based on Ic at 480V)
Protection Type
Code
Description
140U
Molded Case Circuit Breaker
Code
Description
X
Frame Only
Code
Description
2
20…29 kA
b
3
30…39 kA
e
Frame/Rating
5
50…59 kA
Poles
Code
Description
6
60…69 kA
Code
Description
J
250 A
8
80…89 kA
3
3 poles
K
400 A
0
≥100 kA
Q
600 A
M
800 A
Trip Units
140U –
5
a
6
T
D
3
b
c
d
e
– D25
f
a
c
e
Bulletin No.
Trip Unit
Poles
Code
Description
Code
Description
Code
Description
140U
Molded Case Circuit Breaker
T
Trip Unit
3
3 poles
7
8
J
b
d
f
Frame/Rating
Protection Type
Current Range
Code
Description
Code
Description
Code
J
250 A
C
Fixed Thermal/Fixed Magnetic
C
10 rr. A
K
400 A
D
Fixed Thermal/Adjust Magnetic
D
100 rr0 A
L
600 A
E
Adjust Thermal/Fixed Magnetic
E
1000 rr00 A
M
800 A
F
Adjust Thermal/Adjust Magnetic
G
Electronic (LSG — Long, short,
ground fault)
H
Electronic (LSI — Long, short,
high instant)
I
Electronic (LSIG — Long, short,
high instant, ground fault)
L
Electronic (LS — Long and Short time)
S
Molded Case Switch (isolator)
9
10
11
12
13
Visit our website: www.ab.com/catalogs
2-56
Preferred availability cat. nos. are printed in bold
Description
01_140U_100A_G_Frame.qxd
4/23/2008
11:53 AM
Page 2-57
Bulletin 140U
Molded Case Circuit Breakers
Product Selection — 100 A, G-Frame/Accessories
y UL 489
y CSA 22.2, No. 5
Note: Terminal box lugs provided as standard
!
Note: Accessories cannot be field installed to the G-Frame circuit breakers. Circuit breakers with 1 auxiliary contact are
also available.
14 kA, Thermal-Magnetic, Fixed Thermal-Fixed Magnetic
Rated
Current
In [A]
Thermal Trip
[A]
Ir = In (Fixed)
Magnetic Trip
[A]
Im = 10 x In
15
20
25
30
35
40
45
50
15
20
25
30
35
40
45
50
150
200
250
300
350
400
450
500
Interrupt Rating (50/60 Hz)
Icu /Ics [kA]
208V AC
65
65
65
65
65
65
65
65
240V AC
65
65
65
65
65
65
65
65
480V AC
14
14
14
14
14
14
14
14
2 Poles
Interrupt Rating [kA] 9
125/250V DC
Cat. No.
140U-G1C2-C15
10
10
140U-G1C2-C20
140U-G1C2-C25
10
140U-G1C2-C30
10
140U-G1C2-C35
10
140U-G1C2-C40
10
140U-G1C2-C45
10
140U-G1C2-C50
10
2 Poles w/ 1 aux.
contact
Cat. No.
140U-G1C2-C15-A
140U-G1C2-C20-A
140U-G1C2-C25-A
140U-G1C2-C30-A
140U-G1C2-C35-A
140U-G1C2-C40-A
140U-G1C2-C45-A
140U-G1C2-C50-A
1
2
3
9 Time constant is 8 ms min.
22 kA, Thermal-Magnetic, Fixed Thermal-Fixed Magnetic
Rated
Current
In [A]
Thermal Trip
[A]
Ir = In (Fixed)
Magnetic Trip
[A]
Im = 10 x In
15
20
25
30
35
40
45
50
60
70
80
90
100
15
20
25
30
35
40
45
50
60
70
80
90
100
150
200
250
300
350
400
450
500
600
700
800
900
1000
Interrupt Rating (50/60 Hz)
Icu /Ics [kA]
208V AC
65
65
65
65
65
65
65
65
65
65
65
65
65
240V AC
65
65
65
65
65
65
65
65
65
65
65
65
65
480V AC
22
22
22
22
22
22
22
22
22
22
22
22
22
3 Poles
Interrupt Rating [kA] 9
125/250V DC
Cat. No.
140U-G2C3-C15
10
10
140U-G2C3-C20
10
140U-G2C3-C25
140U-G2C3-C30
10
10
140U-G2C3-C35
140U-G2C3-C40
10
140U-G2C3-C45
10
140U-G2C3-C50
10
140U-G2C3-C60
10
140U-G2C3-C70
10
140U-G2C3-C80
10
140U-G2C3-C90
10
140U-G2C3-D10
10
3 Poles w/ 1 aux.
contact
Cat. No.
140U-G2C3-C15-A
140U-G2C3-C20-A
140U-G2C3-C25-A
140U-G2C3-C30-A
140U-G2C3-C35-A
140U-G2C3-C40-A
140U-G2C3-C45-A
140U-G2C3-C50-A
140U-G2C3-C60-A
140U-G2C3-C70-A
140U-G2C3-C80-A
140U-G2C3-C90-A
140U-G2C3-D10-A
4
5
6
7
9 Time constant is 8 ms min. and 2 poles of a 3-pole circuit breaker.
8
Accessories
External Accessories
Description
Rotary, Variable-Depth Operating
Mechanism
UL Type 3/12/4/4X, IP 66 Rotary handle
12 in. (30.48 cm) operating rod
Cat. No.
Black Handle
140U-G-RVM12B
Red/Yellow Handle
140U-G-RVM12R
9
10
DIN Rail Adapter
Allows 2-pole G-frame MCCB to mount to
35 mm DIN Rail
Qty: 1
140U-G-DRA2
11
DIN Rail Adapter
Allows 3-pole G-frame MCCB to mount to
35 mm DIN Rail
Qty: 1
140U-G-DRA3
12
Padlock Kit
Padlocking Hasp
Lock-OFF only
Qty: 1
140U-G-PL
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-57
13
01_140U_100A_G_Frame.qxd
4/23/2008
11:53 AM
Page 2-58
Bulletin 140U
Molded Case Circuit Breakers
Approximate Dimensions — 100 A, G-Frame
3-Pole Dimensions
!
.84
[ 21,3 ]
1
.36
[ 9,1 ]
.45
[ 11,4 ]
2
3
3.00
[ 76,2 ]
4
3.21
[ 81,4 ]
Ø.16
[ 4,1 ]
1.00
[ 25,4 ]
5
6
4.88
[ 123,8 ]
140U
G FRAME
3.22
[ 81,7 ]
7
8
9
1.00
[ 25,4 ]
1.00
[ 25,4 ]
2.41
[ 61,2 ]
10
.45
[ 11,4 ]
11
.36
[ 9,1 ]
2.83
[ 71,8 ]
1.22
[ 31 ]
12
13
Visit our website: www.ab.com/catalogs
2-58
Preferred availability cat. nos. are printed in bold
01_140U_100A_G_Frame.qxd
4/23/2008
11:54 AM
Page 2-59
Bulletin 140U
Molded Case Circuit Breakers
Approximate Dimensions — 100 A, G-Frame, Continued
Dimensions are in inches (millimeters). Dimensions are not intended to be used for manufacturing purposes.
2-Pole Dimensions
!
15-100 AMP, PRESSURE COLLAR TERMINALS
1
.84
[ 21,4 ]
2
.49
[ 12,5 ]
3
2.00
[ 50,8 ]
Ø.14
[ 3,6 ]
1.00
[ 25,4 ]
4
2.42
[ 61,5 ]
5
.97
[ 24,6 ]
6
7
3.22
[ 81,8 ]
8
9
1.00
[ 25,4 ]
3.21
[ 81,5 ]
10
.49
[ 12,4 ]
11
12
1.22
[ 30,9 ]
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-59
02_140U_125A_H_Frame.qxd
4/23/2008
11:59 AM
Page 2-60
Bulletin 140U
Molded Case Circuit Breakers
Product Selection — 125 A, H-Frame
Product Selection — 125 A, H-Frame
!
!
1
2
3
4
5
y UL 489
y CSA 22.2, No. 5
y IEC 60947-2
y CE
y KEMA-KEUR
Note: Terminal box lugs provided as standard
1-Pole 25/18 kA, Thermal-Magnetic, Fixed Thermal-Fixed Magnetic
Breaking Capacity (50 Hz)
Icu /Ics [kA]
Interrupting Rating (60 Hz)
[kA]
Rated
Current
In [A]
Magnetic Trip
[A]
Im = 10 x In
240V
277V
Cat. No.
15
500
25
25
25
18
140U-H1C1-C15
20
500
25
25
25
18
140U-H1C1-C20
25
500
25
25
25
18
140U-H1C1-C25
30
500
25
25
25
18
140U-H1C1-C30
35
500
25
25
25
18
140U-H1C1-C35
40
500
25
25
25
18
140U-H1C1-C40
45
500
25
25
25
18
140U-H1C1-C45
50
500
25
25
25
18
140U-H1C1-C50
60
600
25
25
25
18
140U-H1C1-C60
70
700
25
25
25
18
140U-H1C1-C70
80
800
25
25
25
18
140U-H1C1-C80
90
900
25
25
25
18
140U-H1C1-C90
100
1000
25
25
25
18
140U-H1C1-D10
110
1100
25
25
25
18
140U-H1C1-D11
125
1250
25
25
25
18
140U-H1C1-D12
220…240V
2-Pole 25/25 kA, Thermal-Magnetic, Fixed Thermal-Fixed Magnetic
6
7
8
9
10
Breaking Capacity (50 Hz)
Icu /Ics [kA]
Interrupting Rating (60 Hz)
[kA]
Rated
Current
In [A]
Magnetic Trip
[A]
Im = 10 x In
240V
480V
600/347V
Cat. No.
15
500
35
35
25
25
—
—
—
—
35
25
18
140U-H2C2-C15
20
500
35
35
25
25
—
—
—
—
35
25
18
140U-H2C2-C20
25
500
35
35
25
25
—
—
—
—
35
25
18
140U-H2C2-C25
30
500
35
35
25
25
—
—
—
—
35
25
18
140U-H2C2-C30
35
500
35
35
25
25
—
—
—
—
35
25
18
140U-H2C2-C35
40
500
35
35
25
25
—
—
—
—
35
25
18
140U-H2C2-C40
45
500
35
35
25
25
—
—
—
—
35
25
18
140U-H2C2-C45
50
500
35
35
25
25
—
—
—
—
35
25
18
140U-H2C2-C50
60
600
35
35
25
25
—
—
—
—
35
25
18
140U-H2C2-C60
70
700
35
35
25
25
—
—
—
—
35
25
18
140U-H2C2-C70
80
800
35
35
25
25
—
—
—
—
35
25
18
140U-H2C2-C80
140U-H2C2-C90
220…240V
380…415V
500V
690V
90
900
35
35
25
25
—
—
—
—
35
25
18
100
1000
35
35
25
25
—
—
—
—
35
25
18
140U-H2C2-D10
110
1100
35
35
25
25
—
—
—
—
35
25
18
140U-H2C2-D11
125
1250
35
35
25
25
—
—
—
—
35
25
18
140U-H2C2-D12
11
12
13
Visit our website: www.ab.com/catalogs
2-60
Preferred availability cat. nos. are printed in bold
02_140U_125A_H_Frame.qxd
4/23/2008
12:00 PM
Page 2-61
Bulletin 140U
Molded Case Circuit Breakers
Product Selection — 125 A, H-Frame, Continued
2-Pole 40/35 kA, Thermal-Magnetic, Fixed Thermal-Fixed Magnetic
Rated
Current
In [A]
Thermal Trip
[A]
Ir = In (Fixed)
Magnetic Trip
[A]
Im = 10 x In
15
Fixed
20
Fixed
25
Breaking Capacity (50 Hz)
Icu /Ics [kA]
Interrupting Rating (60 Hz)
[kA]
220…240V
380…415V
500V
690V
500
85
43
40
30
—
—
—
500
85
43
40
30
—
—
—
Fixed
500
85
43
40
30
—
—
30
Fixed
500
85
43
40
30
—
35
Fixed
500
85
43
40
30
40
Fixed
500
85
43
40
30
45
Fixed
500
85
43
40
50
Fixed
500
85
43
60
Fixed
600
85
70
Fixed
700
80
Fixed
800
90
Fixed
100
!
240V
480V
600/347V
Cat. No.
—
85
35
22
140U-H3C2-C15
—
85
35
22
140U-H3C2-C20
—
—
85
35
22
140U-H3C2-C25
—
—
—
85
35
22
140U-H3C2-C30
—
—
—
—
85
35
22
140U-H3C2-C35
—
—
—
—
85
35
22
140U-H3C2-C40
30
—
—
—
—
85
35
22
140U-H3C2-C45
40
30
—
—
—
—
85
35
22
140U-H3C2-C50
43
40
30
—
—
—
—
85
35
22
140U-H3C2-C60
85
43
40
30
—
—
—
—
85
35
22
140U-H3C2-C70
85
43
40
30
—
—
—
—
85
35
22
140U-H3C2-C80
900
85
43
40
30
—
—
—
—
85
35
22
140U-H3C2-C90
Fixed
1000
85
43
40
30
—
—
—
—
85
35
22
140U-H3C2-D10
110
Fixed
1100
85
43
40
30
—
—
—
—
85
35
22
140U-H3C2-D11
125
Fixed
1250
85
43
40
30
—
—
—
—
85
35
22
140U-H3C2-D12
Thermal Trip
[A]
Ir = In (Fixed)
Magnetic
Trip [A]
Im = 10 x In
15
Fixed
500
Breaking Capacity (50 Hz)
Icu /Ics [kA]
220…240V
100
50
380…415V
70
35
690V
—
—
—
240V
480V
600/347V
Cat. No.
100
65
25
140U-H6C2-C15
20
Fixed
500
100
50
70
35
—
—
—
—
100
65
25
140U-H6C2-C20
25
Fixed
500
100
50
70
35
—
—
—
—
100
65
25
140U-H6C2-C25
30
Fixed
500
100
50
70
35
—
—
—
—
100
65
25
140U-H6C2-C30
35
Fixed
500
100
50
70
35
—
—
—
—
100
65
25
140U-H6C2-C35
40
Fixed
500
100
50
70
35
—
—
—
—
100
65
25
140U-H6C2-C40
45
Fixed
500
100
50
70
35
—
—
—
—
100
65
25
140U-H6C2-C45
50
Fixed
500
100
50
70
35
—
—
—
—
100
65
25
140U-H6C2-C50
60
Fixed
600
100
50
70
35
—
—
—
—
100
65
25
140U-H6C2-C60
70
Fixed
700
100
50
70
35
—
—
—
—
100
65
25
140U-H6C2-C70
80
Fixed
800
100
50
70
35
—
—
—
—
100
65
25
140U-H6C2-C80
90
Fixed
900
100
50
70
35
—
—
—
—
100
65
25
140U-H6C2-C90
100
Fixed
1000
100
50
70
35
—
—
—
—
100
65
25
140U-H6C2-D10
110
Fixed
1100
100
50
70
35
—
—
—
—
100
65
25
140U-H6C2-D11
125
Fixed
1250
100
50
70
35
—
—
—
—
100
65
25
140U-H6C2-D12
3-Pole 25/25 kA, Thermal-Magnetic, Fixed Thermal-Fixed Magnetic
Rated
Current
In [A]
15
20
25
30
35
40
45
50
60
70
80
90
100
110
125
Thermal Trip
[A]
Ir = In (Fixed)
15
20
25
30
35
40
40
50
60
70
80
90
100
110
125
Magnetic Trip
[A]
Im = 10 x In
500
500
500
500
500
500
500
500
600
700
800
900
1000
1100
1250
Breaking Capacity (50 Hz)
Icu /Ics [kA]
220…240V
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
380…415V
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
525V
22
22
22
22
22
22
22
22
22
22
22
22
22
22
18
3
Interrupting Rating (60 Hz)
[kA]
500V
—
2
4
2-Pole 70/65 kA, Thermal-Magnetic, Fixed Thermal-Fixed Magnetic
Rated
Current
In [A]
1
690V
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
Interrupting Rating (60 Hz)
[kA]
240V
480V
600/347V
35
25
18
35
25
18
35
25
18
35
25
18
35
25
18
35
25
18
35
25
18
35
25
18
35
25
18
35
25
18
35
25
18
35
25
18
35
25
18
35
25
18
35
25
18
5
6
7
8
9
Cat. No.
140U-H2C3-C15
140U-H2C3-C20
140U-H2C3-C25
140U-H2C3-C30
140U-H2C3-C35
140U-H2C3-C40
140U-H2C3-C45
140U-H2C3-C50
140U-H2C3-C60
140U-H2C3-C70
140U-H2C3-C80
140U-H2C3-C90
140U-H2C3-D10
140U-H2C3-D11
140U-H2C3-D12
10
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-61
02_140U_125A_H_Frame.qxd
4/23/2008
12:01 PM
Page 2-62
Bulletin 140U
Molded Case Circuit Breakers
Product Selection — 125 A, H-Frame, Continued
3-Pole 40/35 kA, Thermal-Magnetic, Fixed Thermal-Fixed Magnetic
!
!
1
2
3
Rated
Current
In [A]
15
20
25
30
35
40
45
50
60
70
80
90
100
110
125
Thermal Trip
[A]
Ir = In (Fixed)
15
20
25
30
35
40
45
50
60
70
80
90
100
110
125
Magnetic Trip
[A]
Im = 10 x In
500
500
500
500
500
500
500
500
600
700
800
900
1000
1100
1250
Breaking Capacity (50 Hz)
Icu /Ics [kA]
220…240V
85
43
85
43
85
43
85
43
85
43
85
43
85
43
85
43
85
43
85
43
85
43
85
43
85
43
85
43
85
43
380…415V
40
30
40
30
40
30
40
30
40
30
40
30
40
30
40
30
40
30
40
30
40
30
40
30
40
30
40
30
40
30
525V
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
Interrupting Rating (60 Hz)
[kA]
240V
480V
600/347V
85
35
22
85
35
22
85
35
22
85
35
22
85
35
22
85
35
22
85
35
22
85
35
22
85
35
22
85
35
22
85
35
22
85
35
22
85
35
22
85
35
22
85
35
22
Cat. No.
140U-H3C3-C15
140U-H3C3-C20
140U-H3C3-C25
140U-H3C3-C30
140U-H3C3-C35
140U-H3C3-C40
140U-H3C3-C45
140U-H3C3-C50
140U-H3C3-C60
140U-H3C3-C70
140U-H3C3-C80
140U-H3C3-C90
140U-H3C3-D10
140U-H3C3-D11
140U-H3C3-D12
3
3
3
3
3
3
3
3
3
3
3
3
3
Interrupting Rating (60 Hz)
[kA]
240V
480V
600/347V
100
65
25
100
65
25
100
65
25
100
65
25
100
65
25
100
65
25
100
65
25
100
65
25
100
65
25
100
65
25
100
65
25
100
65
25
100
65
25
Cat. No.‡
140U-H6C3-C15
140U-H6C3-C20
140U-H6C3-C25
140U-H6C3-C30
140U-H6C3-C40
140U-H6C3-C50
140U-H6C3-C60
140U-H6C3-C70
140U-H6C3-C80
140U-H6C3-C90
140U-H6C3-D10
140U-H6C3-D11
140U-H6C3-D12
6
6
6
6
6
6
6
6
6
6
6
6
6
Interrupting Rating (60 Hz)
[kA]
240V
480V
600/347V
200
100
35
200
100
35
200
100
35
200
100
35
200
100
35
200
100
35
200
100
35
200
100
35
200
100
35
200
100
35
200
100
35
200
100
35
200
100
35
Cat. No.‡
140U-H0C3-C15
140U-H0C3-C20
140U-H0C3-C25
140U-H0C3-C30
140U-H0C3-C40
140U-H0C3-C50
140U-H0C3-C60
140U-H0C3-C70
140U-H0C3-C80
140U-H0C3-C90
140U-H0C3-D10
140U-H0C3-D11
140U-H0C3-D12
690V
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
3-Pole 70/65 kA, Thermal-Magnetic, Fixed Thermal-Fixed Magnetic
4
5
6
7
Rated
Current
In [A]
15
20
25
30
40
50
60
70
80
90
100
110
125
Thermal Trip
[A]
Ir = In (Fixed)
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
Magnetic
Trip [A]
Im = 10 x In
500
500
500
500
500
500
600
700
800
900
1000
1100
1250
Breaking Capacity (50 Hz)
Icu /Ics [kA]
220…240V
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
380…415V
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
525V
25
25
25
25
25
25
25
25
25
25
25
25
25
690V
13
13
13
13
13
13
13
13
13
13
13
13
13
6
6
6
6
6
6
6
6
6
6
6
6
6
‡ Current Limiting
3-Pole 100/100 kA, Thermal-Magnetic, Fixed Thermal-Fixed Magnetic
8
9
10
11
12
Rated
Current
In [A]
15
20
25
30
40
50
60
70
80
90
100
110
125
Thermal Trip
[A]
Ir = In (Fixed)
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
Magnetic
Trip [A]
Im = 10 x In
500
500
500
500
500
500
600
700
800
900
1000
1100
1250
Breaking Capacity (50 Hz)
Icu /Ics [kA]
220…240V
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
380…415V
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
525V
35
35
35
35
35
35
35
35
35
35
35
35
35
690V
18
18
18
18
18
18
18
18
18
18
18
18
18
8
8
8
8
8
8
8
8
8
8
8
8
8
‡ Current Limiting
Molded Case Switch — UL 1087
Rated
Current
In [A]
125
Thermal Trip
[A]
Ir = In (Fixed)
—
Magnetic
Trip [A]
Im = 10 x In
1250
Breaking Capacity (50 Hz)
Icu /Ics [kA]
220…240V
100
50
380…415V
70
35
525V
35
690V
18
6
3
13
Visit our website: www.ab.com/catalogs
2-62
Preferred availability cat. nos. are printed in bold
Interrupting Rating (60 Hz)
[kA]
240V 480V
600/347V
100
65
25
Cat. No.
140U-H6S3-D12
02_140U_125A_H_Frame.qxd
4/23/2008
12:01 PM
Page 2-63
Bulletin 140U
Molded Case Circuit Breakers
Accessories — 125 A, H-Frame
Accessories — 125 A, H-Frame
!
Internal Control Modules — Field Installed
Description
Auxiliary Contact (AX)
Electrically indicates "ON/OFF"
status of breakers
Diagram
Mounting Location
(1) 1a-1b
(2) 1a-1b
Cat. No.
140U-H-EA1
Left AND Right side
1
140U-H-EA2
2
Alarm Contact (AL)
Electrically indicates when the
breaker is in the "TRIPPED" state
(1) 1M (make)1B (break)
140U-H-ER1
3
Right side ONLY
Auxiliary/Alarm Contact (AX/AL)
Combination
Combination of auxiliary contact
and alarm contact
(1) 1a-1b
(1) 1M (make)1B (break)
140U-H-EA1R1
4
Right side ONLY
Shunt Trip (SNT)
Provides remote tripping of the
circuit breaker
Undervoltage trip not available
when shunt trip is used
12V DC
140U-H-SNZQ
24…60V,
50/60/DC
140U-H-SNJ
110…240V,
50/60/DC
140U-H-SND
380…440V AC,
220…250V DC
140U-H-SNN
380…600V,
50/60 Hz
Undervoltage Release (UVT)
Automatically trips breaker when
voltage falls between preset value,
35…70%
Shunt trip is not available when
undervoltage release is used
Left side ONLY
140U-H-SNB
24V, 50/60 Hz
140U-H-UJ
110…127V,
50/60 Hz
140U-H-UD
208…240V,
50/60 Hz
140U-H-UA
380…500V,
50/60 Hz
140U-H-UB
525…600V,
50/60 Hz
Left side ONLY
5
6
7
140U-H-UC
8
Note: For Factory-Installed internal control modules, please see page 2-92
9
10
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-63
02_140U_125A_H_Frame.qxd
4/23/2008
12:01 PM
Page 2-64
Bulletin 140U
Molded Case Circuit Breakers
Accessories — 125 A, H-Frame, Continued
125 A, H-Frame, Continued
!
!
External Accessories
Description
1
Cat. No.
Terminal End Cover
6.4 mm (0.25 in.) diameter cable entry
140U-H-TC2
Terminal End Cover
10.4 mm (0.41 in.) diameter cable entry
140U-H-TC4
Terminal Shields
IP20 Ingress Protection Rating
2
140U-H-TS
Flex-Cable Operating Mechanism
Includes handle, cable, operating, and bail mechanism
Pre-assembled and adjusted
Non-Metallic - UL IP66, Type 1/3/12/4/4X
Flange Mount Operating Handle
3
Flex-Cable Operating Mechanism
Includes handle, cable, operating, and bail mechanism
Pre-assembled and adjusted
Stainless Steel - Type 4/4X
Flange Mount Operating Handle
4
Rotary, Variable-Depth Operating Mechanism
UL Type 3/12/4/4X, IP 66 Rotary handle
12 in. (30.48 cm) operating rod
140U-H-FCX06
10 ft (3.0 m) Cable
140U-H-FCX10
3 ft (0.9 m) Cable
140U-H-FCS03
4 ft (1.2 m) Cable
140U-H-FCS04
6 ft (1.9 m) Cable
140U-H-FCS06
10 ft (3.0 m) Cable
140U-H-FCS10
Black Handle
140U-H-RVM12B
140U-H-RVM12R
140U-H-RVM21B
Red/Yellow Handle
140U-H-RVM21R
Black Handle
140U-H-NVM12B
Red/Yellow Handle
140U-H-NVM12R
Black Handle
140U-H-NVM21B
Red/Yellow Handle
140U-H-NVM21R
Motor Operator
Remotely opens, closes, and resets the circuit breaker
110…240V AC
For use with 3- or 4Pole MCCBs,
110…240V AC/DC
140U-H-EOPD
Motor Operator
Remotely opens, closes, and resets the circuit breaker
24V DC
For use with 3- or 4Pole MCCBs, 24V
DC
140U-H-EOPZ
Mounting Hardware
(4) M4 - 0.7 x 75 mm
For use with 3- or 4Pole MCCBs
140U-H-MHM
Rotary, Variable-Depth Operating Mechanism with Internal NFPA 79 Operating Handle
Type 3/4/4X/12 IP66 Rotary Handle
21 in. (53.34 cm) operating rod
7
140U-H-FCX04
6 ft (1.9 m) Cable
Black Handle
Rotary, Variable-Depth Operating Mechanism with Internal NFPA 79 Operating Handle
Type 3/4/4X/12 IP66 Rotary Handle
12 in. (30.48 cm) operating rod
6
140U-H-FCX03
Red/Yellow Handle
Rotary, Variable-Depth Operating Mechanism
UL Type 3/12/4/4X, IP 66 Rotary handle
21 in. (53.34 cm) operating rod
5
3 ft (0.9 m) Cable
4 ft (1.3 m) Cable
8
9
10
11
12
13
Visit our website: www.ab.com/catalogs
2-64
Preferred availability cat. nos. are printed in bold
02_140U_125A_H_Frame.qxd
4/23/2008
12:01 PM
Page 2-65
Bulletin 140U
Molded Case Circuit Breakers
Accessories — 125 A, H-Frame, Continued
125 A, H-Frame, Continued
!
External Accessories, Continued
Description
Cat. No.
Black Handle
140U-H-RCB
Red/Yellow Handle
140U-H-RCR
End Cap Kit
Provides three-phase connections for terminal or bolt-on
connections
Metric hardware provided
Qty: 1
140U-H-ECM
2
Phase Barriers
Provides additional phase clearance when special connections that
extend past the circuit breaker housing are required
Qty: 2
140U-H-PB
3
Padlock Kit
Padlocking hasp
Lock-OFF only
Qty: 1
140U-H-PL
Rotary, Direct Couple Operating
Mechanism
Rotary handle - IP42 UL Type 1
Breaker mounted
1
4
Plug-in Base Adapters
Plug-in provides power
terminations and adapter for
applications where the ability to
quickly remove or replace the
circuit breakers is required
Plug-in Base Auxiliary
Contacts
Provides auxiliary contact
functions to detect breaker
installation status
5
For use with 3-Pole MCCBs
Qty: 1
140U-H-PAD3
6
For use with 3- or 4-Pole
MCCBs
Qty: 1
140U-H-PDK
7
DIN Rail Adapter
Allows H-frame MCCB to mount
to 35 mm DIN Rail
For use with 3-Pole H-Frame
MCCBs
Qty: 1
140U-H-DRA
8
Multi-Tap Terminal Lug Kit —
with IP20 terminal cover
Cat. No. 140U-H-MTL3AN
Multi-Tap Terminal Lug Kit —
with IP20 terminal cover
Qty: 3 with terminal shield
140U-H-MTL3A
Qty: 3
140U-H-MTL3AN
(6) #14…6 AWG
or (6) 2.5…10 mm2
Qty: 3 with terminal shield
140U-H-MTL6A
(6) #14…6 AWG
or (6) 2.5…10 mm2
Qty: 3
140U-H-MTL6AN
(3) #14…2 AWG
or (3) 2.5…35 mm2
9
10
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-65
02_140U_125A_H_Frame.qxd
4/23/2008
12:01 PM
Page 2-66
Bulletin 140U
Molded Case Circuit Breakers
Approximate Dimensions — 125 A, H-Frame
Dimensions are in inches. Dimensions are not intended to be used for manufacturing purposes.
!
!
1-Pole Molded Case Circuit Breakers
0.907
1
TOP
2
3
FNT
2.497
0.984
4
FNT
5
6
8
5.50
3.812
7
RGT
RGT
9
TOP
2.913
10
3.476
11
12
13
Visit our website: www.ab.com/catalogs
2-66
Preferred availability cat. nos. are printed in bold
02_140U_125A_H_Frame.qxd
4/23/2008
12:01 PM
Page 2-67
Bulletin 140U
Molded Case Circuit Breakers
Approximate Dimensions — 125 A, H-Frame, Continued
Dimensions are in inches. Dimensions are not intended to be used for manufacturing purposes.
!
2-Pole Molded Case Circuit Breakers
0.8524
1
0.4179
TOP
2
3.414
FNT
3
1.973
FNT
4
0.168
5
RGT
RGT
3.812
6
7
TOP
1.007
8
FNT
2.9725
TOP
9
10
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-67
02_140U_125A_H_Frame.qxd
4/23/2008
12:01 PM
Page 2-68
Bulletin 140U
Molded Case Circuit Breakers
Approximate Dimensions — 125 A, H-Frame, Continued
Dimensions are in inches (millimeters). Dimensions are not intended to be used for manufacturing purposes.
!
!!
3-Pole Molded Case Circuit Breakers
4 Ð .17 (4.32) x .19 (4.83) Dia.
Slot for #6 Mounting Screws
Line End
.50
.50
(12.70) (12.70)
.45
(11.43)
6 Ð .35 (8.90) Dia.
11
.78
(19.81)
.09
(2.29)
.58
(14.73)
.56
(14.22)
.22
(5.59)
22
Attachment
Leads Side
Exit Point
5.50
(139.70)
33
Push to
Trip Button
3.81
(96.78)
44
3.03
(76.96)
.17
(4.32)
55
C
L
.15
(3.81)
E
D
1.38
(35.05)
A
.57
(14.48)
1.08
(27.43)
.72
(18.29)
.20 (5.08) Dia.
Thru Conductors
2.18
(55.37)
.22
(5.59)
B
.17
(4.32)
66
Handle
R2.13
1.73
(43.94)
.09
(2.29)
.55
(13.97)
2.77
(70.36)
2.93
2.99 (74.42)
(75.95)
C
1.00
(25.40)
1.00
(25.40)
77
.03
(0.76)
.77
(19.56)
1.42
(36.07)
1.21
(30.73)
3.00
(76.20)
1.50
(38.10)
88
.94
(23.88)
.44
(11.18)
.47
(11.94)
Attachment
Leads Rear
Exit Point
99
10
10
Breaker Status
Dimension
A
B
C
D
E
On
2.71
(68.83)
2.53
(64.26)
3.46
(87.88)
2.83
(71.88)
2.75
(69.85)
Off
1.54
(39.12)
1.62
(41.15)
3.46
(87.88)
1.66
(42.16)
1.84
(46.74)
Tripped
2.33
(59.18)
2.23
(56.64)
3.54
(89.92)
2.46
(67.48)
2.45
(62.23)
Reset
1.39
(35.31)
1.49
(37.85)
3.42
(86.87)
1.52
(38.61)
1.70
(43.18)
1.44
(36.58)
11
11
.67
(17.02)
12
13
Visit our website: www.ab.com/catalogs
2-68
Preferred availability cat. nos. are printed in bold
03_140U_250A_J_Frame.qxd
4/23/2008
12:10 PM
Page 2-69
Bulletin 140U
Molded Case Circuit Breakers
Product Selection — 250 A, J-Frame
y UL 489
y CSA 22.2, No. 5
y IEC 60947-2
y CE
y KEMA-KEUR (Pending)
Note: Terminal box lugs must be ordered separately. See page 2-72
!
Breaker Frames
1
Breaking Capacity (50 Hz)
Icu /Ics [kA]
Rated
Current
In [A]
220…240V
65
250
380…415V
Interrupting Rating (60 Hz)
[kA]
525V
690V
65
25
25
18
12
12
6
240V
480V
600V
Cat. No.
65
25
18
140U-J2X3
2
85
85
45
45
18
12
12
6
85
35
18
100
100
70
70
25
13
14
7
100
65
25
‡
140U-J6X3
200
200
100
100
35
18
16
12
200
100
35
‡
140U-J0X3
140U-J3X3
‡ Current Limiting
3
Trip Units
Thermal-Magnetic
Electronic
Adjustment Range [A]
Rated Current
In [A]
Thermal Trip
Ιr = Ιn (Fixed)
Adjustment Range [A]
Magnetic Trip
Ιm = 5…10 x Ιr
Cat. No.
Rated
Current In
[A]
Thermal Trip
Ιr = 0.4…1.0 x Ιn
Magnetic Trip
Ιm = 2…14 x Ιr
Protection
Type
Cat. No.
90
90
450…900
140U-JTD3-C90
50
20…50
40…700
LS
140U-JTL3-C50
100
100
500…1000
140U-JTD3-D10
50
20…50
40…700
LSI
140U-JTH3-C50
125
125
600…1250
140U-JTD3-D12
50
20…50
40…700
LSG
140U-JTG3-C50
150
150
750…1500
140U-JTD3-D15
50
20…50
40…700
LSIG
140U-JTI3-C50
175
175
875…1750
140U-JTD3-D17
100
40…100
80…1400
LS
140U-JTL3-D10
200
200
1000…2000
140U-JTD3-D20
100
40…100
80…1400
LSI
140U-JTH3-D10
225
225
1125…2250
140U-JTD3-D22
100
40…100
80…1400
LSG
140U-JTG3-D10
250
250
1250…2500
140U-JTD3-D25
100
40…100
80…1400
LSIG
140U-JTI3-D10
160
63…160
126…2240
LS
140U-JTL3-D16
160
63…160
126…2240
LSI
140U-JTH3-D16
160
63…160
126…2240
LSG
140U-JTG3-D16
160
63…160
126…2240
LSIG
140U-JTI3-D16
250
100…250
200…3500
LS
140U-JTL3-D25
250
100…250
200…3500
LSI
140U-JTH3-D25
250
100…250
200…3500
LSG
140U-JTG3-D25
250
100…250
200…3500
LSIG
140U-JTI3-D25
4
5
6
7
8
Assembled Circuit Breakers with Thermal-Magnetic Trip Units
Breaking Capacity/
Interrupting Rating
[kA]7
Breaking Capacity/
Interrupting Rating
[kA]7
Breaking Capacity/
Interrupting Rating
[kA]7
Rated Current In [A]
400V
480V
Cat. No.
400V
480V
Cat. No.
400V
480V
Cat. No.
140U-J6D3-C90
90
25
25
140U-J2D3-C90
40
35
140U-J3D3-C90
70
65
100
25
25
140U-J2D3-D10
40
35
140U-J3D3-D10
70
65
140U-J6D3-D10
125
25
25
140U-J2D3-D12
40
35
140U-J3D3-D12
70
65
140U-J6D3-D12
150
25
25
140U-J2D3-D15
40
35
140U-J3D3-D15
70
65
140U-J6D3-D15
175
25
25
140U-J2D3-D17
40
35
140U-J3D3-D17
70
65
140U-J6D3-D17
200
25
25
140U-J2D3-D20
40
35
140U-J3D3-D20
70
65
140U-J6D3-D20
225
25
25
140U-J2D3-D22
40
35
140U-J3D3-D22
70
65
140U-J6D3-D22
250
25
25
140U-J2D3-D25
40
35
140U-J3D3-D25
70
65
140U-J6D3-D25
9
10
11
7 Full ratings are found in the breaker frames table on this page
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-69
03_140U_250A_J_Frame.qxd
4/23/2008
12:10 PM
Page 2-70
Bulletin 140U
Molded Case Circuit Breakers
Product Selection — 250 A, J-Frame, Continued
Assembled Circuit Breakers with Electronic Trip Units
Breaking
Capacity/
Interrupting
Rating [kA]7
!
Breaking
Capacity/
Interrupting
Rating [kA]7
Breaking
Capacity/
Interrupting
Rating [kA]7
Rated Current
In [A]
Protection Type
400V
480V
Cat. No.
400V
480V
Cat. No.
400V
480V
Cat. No.
50
LS
25
25
140U-J2L3-C50
40
35
140U-J3L3-C50
70
65
140U-J6L3-C50
1
2
3
4
50
LSI
25
25
140U-J2H3-C50
40
35
140U-J3H3-C50
70
65
140U-J6H3-C50
50
LSG
25
25
140U-J2G3-C50
40
35
140U-J3G3-C50
70
65
140U-J6G3-C50
50
LSIG
25
25
140U-J2I3-C50
40
35
140U-J3I3-C50
70
65
140U-J6I3-C50
100
LS
25
25
140U-J2L3-D10
40
35
140U-J3L3-D10
70
65
140U-J6L3-D10
100
LSI
25
25
140U-J2H3-D10
40
35
140U-J3H3-D10
70
65
140U-J6H3-D10
100
LSG
25
25
140U-J2G3-D10
40
35
140U-J3G3-D10
70
65
140U-J6G3-D10
100
LSIG
25
25
140U-J2I3-D10
40
35
140U-J3I3-D10
70
65
140U-J6I3-D10
160
LS
25
25
140U-J2L3-D16
40
35
140U-J3L3-D16
70
65
140U-J6L3-D16
160
LSI
25
25
140U-J2H3-D16
40
35
140U-J3H3-D16
70
65
140U-J6H3-D16
160
LSG
25
25
140U-J2G3-D16
40
35
140U-J3G3-D16
70
65
140U-J6G3-D16
160
LSIG
25
25
140U-J2I3-D16
40
35
140U-J3I3-D16
70
65
140U-J6I3-D16
250
LS
25
25
140U-J2L3-D25
40
35
140U-J3L3-D25
70
65
140U-J6L3-D25
250
LSI
25
25
140U-J2H3-D25
40
35
140U-J3H3-D25
70
65
140U-J6H3-D25
250
LSI
25
25
140U-J2G3-D25
40
35
140U-J3H3-D25
70
65
140U-J6G3-D25
250
LSIG
25
25
140U-J2I3-D25
40
35
140U-J3I3-D25
70
65
140U-J6I3-D25
7 Full ratings are found in the breaker frames table on page 2-69
5
6
Molded Case Switch — UL 489
Rated
Current
In [A]
Thermal Trip
Ιr = Ιn [A]
Magnetic Trip
[A]
Ιm = 10 x Ιn
250
—
2500
Breaking Capacity (50 Hz)
Ιcu /Ιcs [kA]
220…240V
100
100
380…415V
70
70
Interrupting Rating
(60 Hz) [kA]
500V
42
690V
20
7
7
8
9
10
11
12
13
Visit our website: www.ab.com/catalogs
2-70
Preferred availability cat. nos. are printed in bold
3
240V
100
480V
65
600V
25
Cat. No.
140U-J6S3-D25
03_140U_250A_J_Frame.qxd
4/23/2008
12:10 PM
Page 2-71
Bulletin 140U
Molded Case Circuit Breakers
Accessories — 250 A, J-Frame
Internal Control Modules — Field Installed
Description
Auxiliary Contact (AX)
Electrically indicates
"ON/OFF" status of
breakers
Diagram
Mounting Location
(1) 1a-1b
!
140U-H-EA1
(2) 1a-1b
Alarm Contact (AL)
Electrically indicates when
the breaker is in the
"TRIPPED" state
Cat. No.
Left AND Right side
(1) 1M (make)-1B (break)
140U-H-EA2
140U-J-ER1
1
2
Right side ONLY
Auxiliary/Alarm Contact
(AX/AL)
Combination
Combination of auxiliary
contact and alarm contact
3
(1) 1a-1b
(1) 1M (make)-1B (break)
140U-J-EA1R1
Right side ONLY
Shunt Trip (SNT)
Provides remote tripping of
the circuit breaker
Undervoltage trip not
available when shunt trip is
used
12V DC
140U-H-SNZQ
24…60V, 50/60/DC
140U-H-SNJ
110…240V, 50/60/DC
140U-H-SND
380…440V AC, 220…250V
DC
140U-H-SNN
140U-H-SNB
380…600V, 50/60 Hz
12V DC
Undervoltage Release
(UVT)
Automatically trips breaker
when voltage falls between
preset value, 35…70%
Shunt trip is not available
when undervoltage release
is used
Left side ONLY
24V, 50/60 Hz
140U-H-UJ
140U-H-UD
208…240V, 50/60 Hz
140U-H-UA
380…500V, 50/60 Hz
140U-H-UB
Left side ONLY
5
140U-H-SNZQ
110…127V, 50/60 Hz
525…600V, 50/60 Hz
4
6
140U-H-UC
7
Note: For Factory-Installed internal control modules, please see page 2-92
Terminal Lugs
Description
Terminal Lugs
Aluminum lugs, Al or Cu wire
(1) 4…350 MCM
or (1) 25…185 mm2
Stainless Steel Box Lugs,
Cu wire Only
(1) 4…350 MCM
or (1) 25…185 mm2
Frame Size
Cat. No.
Qty: 1
J
140U-J-TLA1
Qty: 1
J
140U-J-TLS1
8
9
10
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-71
03_140U_250A_J_Frame.qxd
4/23/2008
12:11 PM
Page 2-72
Bulletin 140U
Molded Case Circuit Breakers
Accessories — 250 A, J-Frame, Continued
External Accessories
Description
!
Cat. No.
Terminal Shields
IP20 Ingress Protection Rating
140U-J-TS
Flex-Cable Operating Mechanism
Includes handle, cable, operating, and bail mechanism
Pre-assembled and adjusted
Non-Metallic - UL IP66, Type 1/3/12/4/4X
Flange Mount Operating Handle
1
Flex-Cable Operating Mechanism
Stainless Steel IP66/ UL Type 1/3/12/4/4X
Flange-Mount Operating Handle
2
Rotary, Variable-Depth Operating Mechanism
UL Type 3/12/4/4X, IP 66 Rotary handle
12 in. (30.48 cm) operating rod
3
4
140U-J-FCX03
140U-J-FCX04
6 ft (1.9 m) Cable
140U-J-FCX06
10 ft (3.0 m) Cable
140U-J-FCX10
3 ft (0.9 m) Cable
140U-J-FCS03
4 ft (1.2 m) Cable
140U-J-FCS04
6 ft (1.9 m) Cable
140U-J-FCS06
10 ft (3.0 m) Cable
140U-J-FCS10
Black Handle
140U-J-RVM12B
Red/Yellow Handle
140U-J-RVM12R
Rotary, Variable-Depth Operating Mechanism
UL Type 3/12/4/4X, IP 66 Rotary handle
21 in. (53.34 cm) operating rod
Black Handle
140U-J-RVM21B
Red/Yellow Handle
140U-J-RVM21R
Rotary, Variable-Depth Operating Mechanism with Internal NFPA 79 Operating Handle
Type 3/4/4X/12 IP66 Rotary Handle
12 in. (30.48 cm) operating rod
Black Handle
140U-J-NVM12B
Red/Yellow Handle
140U-J-NVM12R
Black Handle
140U-J-NVM21B
Red/Yellow Handle
140U-J-NVM21R
Black Handle
140U-J-RCB
Red/Yellow Handle
140U-J-RCR
Rotary, Variable-Depth Operating Mechanism with Internal NFPA 79 Operating Handle
Type 3/4/4X/12 IP66 Rotary Handle
21 in. (53.34 cm) operating rod
5
Rotary, Direct Couple Operating Mechanism
Breaker mounted
6
3 ft (0.9 m) Cable
4 ft (1.3 m) Cable
End Cap Kit
Provides 3-phase connections for
terminal or bolt-on connections
Metric hardware
7
8
140U-J-ECM
Phase Barriers
Provides additional phase clearance when special connections that extend past the circuit
breaker housing are required
Qty: 2
140U-J-PB
Padlock Kit
Padlocking hasp
Lock-OFF only
Qty: 1
140U-J-PL
(3) #14…#2 AWG
or (3) 2.5…25 mm2
Qty: 3
140U-J-MTL3A
(6) #14…#6 AWG
or (6) 2.5…10 mm2
Qty: 3
140U-J-MTL6A
150 A
For use with
J-Frame 3 pole
MCCBs up to 150 A
140U-J-GFP1503
250 A
For use with
J-Frame 3-pole
MCCBs up to 250 A
140U-J-GFP2503
For use with 3- or
4-Pole MCCBs,
110…240V AC/DC
140U-J-EOPD
For use with 3- or
4-Pole MCCBs,
24V DC
140U-J-EOPZ
For use with 3- or
4-Pole MCCBs
140U-J-MHM
Multi-Tap Terminal Lug Kit — with IP20
terminal cover
9
Ground Fault Leakage Module
Current pickup settings are selectable from
0.03…10 A with time delays up to. Time
delays are also selectable from
Instantaneous…1.0 s for 0.10 A settings and
above. A current pickup setting of 0.03 A
defaults to an Instantaneous time setting
regardless of the time dial’s position. Two
alarm contacts come as standard: a 50%
pretrip and a 100% after trip contact, both
based only on earth leakage current levels.
10
11
Motor Operator
Remotely opens, closes, and resets the circuit breaker
110…240V AC
12
Mounting Hardware
(4) M4 - 0.7 x 90 mm
13
Visit our website: www.ab.com/catalogs
2-72
Preferred availability cat. nos. are printed in bold
03_140U_250A_J_Frame.qxd
4/23/2008
12:11 PM
Page 2-73
Bulletin 140U
Molded Case Circuit Breakers
Approximate Dimensions — 250 A, J-Frame
Dimensions are in inches (millimeters). Dimensions are not intended to be used for manufacturing purposes.
5.048
.170
!
4.125
6.000
2.062
4.453
#8-32 TAP
4 HOLES
5.642
1.541
.281
THERMAL ADJUSTMENT
5.500
.256
3.922
.110 X .310 DEEP
R
TYP(4)
Ø.145
7.000
5.500
4 HOLES
1
BREAKER HANDLE
H
.688
2.750
4.125
1.375
.664
2.062
.688
.203
1.375
2
FRONT CONNECTED DRILL PLAN
GNETIC ADJUST
PUSH TO TRIP
2.906
.897
Ø.650
TYP(6)
4.125
3.978
.500
2.062
Ø.625
6 HOLES
û
1.188
TRIP
.594
R2.656
4.0û
.500
3
7.000
û
BREAKER HANDLE
6.000
4.427
3.570
3.440
3.344
1.375
3.344
3.194
1.906
REF
2.750
.187
.188
4
REAR CONNECTED STUDS
1.771
.624
2.062
.125
Ø.198
.625
.625
1.000
.125
7.000
R.188
1.875
3.922
.173
.949
4.938
BREAKER
K HANDLE
5
.859
1.062
.949
.500
6
.281
2.000
4.000
.260
7
8
9
10
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-73
04_140U_400A_K_Frame.qxd
4/23/2008
12:05 PM
Page 2-74
Bulletin 140U
Molded Case Circuit Breakers
Product Selection — 400 A, K-Frame
y UL 489
y CSA 22.2, No. 5
y IEC 157-1
y KEMA-KEUR
!
1
Note: Terminal lugs must be ordered separately. See page 2-75
Breaker Frames
Breaking Capacity (50 Hz)
Icu /Ics [kA]
Rated Current
In [A]
2
220…240V
400
380…415V
65
65
100
100
200
200
Interrupting Rating (60 Hz) [kA]
240V
480V
600V
Cat. No.
40
30
30
10
5
65
35
25
140U-K3X3
35
35
50
38
13
6
100
65
35
140U-K6X3
100
100
65
49
18
9
200
100
50
140U-K0X3
40
500V
690V
Trip Units and Rating Plugs
3
Thermal-Magnetic
Electronic
Adjustment Range [A]
Rated
Current Thermal Trip [A]
Ir = In (Fixed)
In [A]
4
5
6
Magnetic Trip
Im = 5…10 x In
Cat. No.
Rated
Current In
[A]
Adjustment Range [A]
Thermal Trip
Ir = 0.5…1.0 x In
Magnetic Trip
Im = 2…8 x Ir
Protection Type
Cat. No.
LS
140U-KTL3-D40
100
100
500…1000
140U-KTD3-D10
125
125
625…1250
140U-KTD3-D12
150
150
750…1500
140U-KTD3-D15
175
175
895…1750
140U-KTD3-D17
200
200
1000…2000
140U-KTD3-D20
225
225
1125…2250
140U-KTD3-D22
250
250
1250…2500
140U-KTD3-D25
Thermal Trip Ιn
Cat. No.
Thermal Trip Ιn[A]
Cat. No.
300
300
1500…3000
140U-KTD3-D30
200
140U-KRP3-D20
300
140U-KRP3-D30
350
350
1750…3500
140U-KTD3-D35
225
140U-KRP3-D22
350
140U-KRP3-D35
400
400
2000…4000
140U-KTD3-D40
250
140U-KRP3-D25
400
140U-KRP3-D40
400
200…4009
400…3200
LSI
140U-KTH3-D40
LSG
140U-KTG3-D40
LSIG
140U-KTI3-D40
Rating Plugs
Assembled Circuit Breakers, Thermal-Magnetic Trip Units
7
8
9
10
Breaking
Capacity/
Interrupting
Rating [kA]7
Breaking
Capacity/
Interrupting
Rating [kA]7
Breaking
Capacity/
Interrupting
Rating [kA]7
Rated
Current
In [A]
400V
480V
Cat. No.
400V
480V
Cat. No.
400V
480V
Cat. No.
100
40
35
140U-K3D3-D10
65
65
140U-K6D3-D10
100
100
140U-K0D3-D10
125
40
35
140U-K3D3-D12
65
65
140U-K6D3-D12
100
100
140U-K0D3-D12
150
40
35
140U-K3D3-D15
65
65
140U-K6D3-D15
100
100
140U-K0D3-D15
175
40
35
140U-K3D3-D17
65
65
140U-K6D3-D17
100
100
140U-K0D3-D17
200
40
35
140U-K3D3-D20
65
65
140U-K6D3-D20
100
100
140U-K0D3-D20
225
40
35
140U-K3D3-D22
65
65
140U-K6D3-D22
100
100
140U-K0D3-D22
250
40
35
140U-K3D3-D25
65
65
140U-K6D3-D25
100
100
140U-K0D3-D25
300
40
35
140U-K3D3-D30
65
65
140U-K6D3-D30
100
100
140U-K0D3-D30
350
40
35
140U-K3D3-D35
65
65
140U-K6D3-D35
100
100
140U-K0D3-D35
400
40
35
140U-K3D3-D40
65
65
140U-K6D3-D40
100
100
140U-K0D3-D40
Assembled circuit breakers can be created by adding a trip unit and rating plugs (electronic only) to a circuit breaker frame. Example: Cat. No. 140U-K3X3 +
140U-KTL3-D40 + 140U-KRP3-D35
7 Full ratings are found in the breaker frames table on this page
11
12
13
Visit our website: www.ab.com/catalogs
2-74
Preferred availability cat. nos. are printed in bold
04_140U_400A_K_Frame.qxd
4/23/2008
12:05 PM
Page 2-75
Bulletin 140U
Molded Case Circuit Breakers
Product Selection — 400 A, K-Frame, Continued
Assembled Circuit Breakers, Electronic Trip Units
Breaking Capacity/
Interrupting Rating
[kA]7
Breaking Capacity/
Interrupting Rating
Rated
[kA]7
Thermal Trip
Protection
Current In
Ιr = 0.5…1.0 x Ιn
[A]
400V
480V
Type
LS
400
40
35
Breaking Capacity/
Interrupting Rating
[kA]7
!
Cat. No.
400V
480V
Cat. No.
400V
480V
Cat. No.
140U-K3L3-D40
65
65
140U-K6L3-D40
100
100
140U-K0L3-D40
LSI
40
35
140U-K3H3-D40
65
65
140U-K6H3-D40
100
100
140U-K0H3-D40
LSG
40
35
140U-K3G3-D40
65
65
140U-K6G3-D40
100
100
140U-K0G3-D40
100…4009
1
9 Select proper rating plug to cover thermal trip requirement.
7 Full ratings are found in the breaker frames table on page 2-74
2
Molded Case Switch — UL 489
Breaking Capacity (50 Hz) Ιcu /Ιcs [kA]
Magnetic Trip
Rated
10 x Ιn
Current In [A]
400
4000
220…240V
100
100
380…415V
65
65
Interrupting Rating (60 Hz) [kA]
500V
50
690V
38
13
6
240V
100
480V
65
600V
35
Cat. No.
140U-K6S3-D40
3
Optional Terminal Lug Kits
Description
Pkg. Quantity
Aluminum lug, Al or Cu wire
(1) 3…350 MCM
or (1) 30…185 mm2
Terminal Lugs
Aluminum lug, Al or Cu wire
(1) 250…500 MCM
or (1) 120…240 mm2
Aluminum lug, Al or Cu wire
(2) 3/0…250 MCM
or (2) 95…120 mm2
Copper lug, Cu wire only
(1) 3…350 MCM
or (1) 30…185 mm2
Copper lug, Cu wire only
(1) 250…500 MCM
or (1) 120…240 mm2
Terminal Lugs
Copper lug, Cu wire only
(2) 3/0…250 MCM
or (2) 95…120 mm2
Aluminum lug, Al or Cu wire
(2) 2/0…250 MCM
or (1) 2/0…500 MCM,
(2) 70…120 mm2
or (1) 70…240 mm2
140U-K-TLA1A
Multi-Tap Terminal Lug Kit —
with IP20 terminal cover
4
1
140U-K-TLA1
3 (includes shield)
140U-K-TLA2
5
140U-K-TLC1A
1
140U-K-TLC1
3 (includes shield)
6
140U-K-TLC2
7
140U-K-TLA2A
3 (includes shield)
Aluminum lug, Al or Cu wire
(1) 500…750 MCM
or (1) 300…400 mm2
Terminal Lugs
Cat. No.
140U-K-TLA1B
Copper lug, Cu wire only
(1) 500…750 MCM
or (1) 300…400 mm2
3 (includes shield)
140U-K-TLC1B
(3) #12…2/0 AWG
or (3) 4…67 mm2
3
140U-K-MTL3A
(6) #14…#2 AWG
or (6) 2.5…33 mm2
3
140U-K-MTL6A
8
9
10
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-75
04_140U_400A_K_Frame.qxd
4/23/2008
12:06 PM
Page 2-76
Bulletin 140U
Molded Case Circuit Breakers
Accessories — 400 A, K-Frame
Internal Control Modules — Field Installed
!
!
Description
Auxiliary Contact (AX)
Electrically indicates
"ON/OFF" status of
breakers
1
Diagram
(1) 1a-1b
(2) 1a-1b
Alarm Contact (AL)
Electrically indicates when
the breaker is in the
"TRIPPED" state
2
Mounting Location
Cat. No.
140U-K-EA1
Left AND Right side
(1) 1M (make)-1B (break)
140U-K-EA2
140U-K-ER1
Right side ONLY
3
Auxiliary/Alarm Contact
(AX/AL)
Combination
Combination of auxiliary
contact and alarm contact
4
Right side ONLY
5
Shunt Trip (SNT)
Provides remote tripping of
the circuit breaker
Undervoltage trip not
available when shunt trip is
used
6
Undervoltage Release
(UVT)
Automatically trips breaker
when voltage falls between
preset value, 35…70%
Shunt trip is not available
when undervoltage release
is used
7
8
140U-KEA1R1
(1) 1a-1b
(1) 1M (make)-1B (break)
12…24V, 50/60/DC
140U-K-SNJ
110…240V AC,
110…125V DC
140U-K-SND
380…440V AC,
220…250V DC
140U-K-SNN
480…600V, 50/60 Hz
140U-K-SNB
140U-K-UJ
110…127V, 50/60 Hz
140U-K-UD
208…240V, 50/60 Hz
140U-K-UA
380…500V, 50/60 Hz
Note: For Factory-Installed internal control modules, please see page 2-92
9
10
11
12
13
Visit our website: www.ab.com/catalogs
2-76
Left side ONLY
24V, 50/60 Hz
Preferred availability cat. nos. are printed in bold
Left side ONLY
140U-K-UB
04_140U_400A_K_Frame.qxd
4/23/2008
12:07 PM
Page 2-77
Bulletin 140U
Molded Case Circuit Breakers
Accessories — 400 A, K-Frame, Continued
External Accessories
Description
Cat. No.
Terminal Shields
140U-K-TS
Flex-Cable Operating Mechanism
Includes handle, cable, operating, and bail mechanism
Pre-assembled and adjusted
UL Type 1/3/12/4/4X
Flange-Mount Operating Handle
Non-Metallic
Flex-Cable Operating Mechanism
Includes handle, cable, operating, and bail mechanism
Pre-assembled and adjusted
UL Type 4/4X
Flange-Mount Operating Handle
Stainless Steel
4 ft (1.3 m) Cable
140U-K-FCX04
6 ft (1.9 m) Cable
140U-K-FCX06
1
10 ft (3.0 m) Cable
140U-K-FCX10
4 ft (1.2 m) Cable
140U-K-FCS04
6 ft (1.9 m) Cable
140U-K-FCS06
10 ft (3.0 m) Cable
140U-K-FCS10
Rotary, Variable-Depth Operating Mechanism
UL Type 3/12/4/4X, IP 66 Rotary handle
12 in. (30.48 cm) operating rod
Black Handle
140U-K-RVM12B
Red/Yellow Handle
140U-K-RVM12R
Rotary, Variable-Depth Operating Mechanism
UL Type 3/12/4/4X, IP 66 Rotary handle
21 in. (53.34 cm) operating rod
Black Handle
140U-K-RVM21B
Red/Yellow Handle
140U-K-RVM21R
Black Handle
140U-K-NVM12B
Red/Yellow Handle
140U-K-NVM12R
Black Handle
140U-K-NVM21B
Rotary, Variable-Depth Operating Mechanism with Internal NFPA 79 Operating Handle
UL Type 3/12/4/4X, IP 66 Rotary Handle
12 in. (30.48 cm) operating rod
Rotary, Variable-Depth Operating Mechanism with Internal NFPA 79 Operating Handle
UL Type 3/12/4/4X, IP 66 Rotary Handle
21 in. (53.34 cm) operating rod
!
Red/Yellow Handle
140U-K-NVM21R
Rotary, Direct Couple Operating Mechanism
Type 1 Rotary Handle
Breaker Mounted
Black Handle
140U-K-RCG
Rotary, Direct Couple Operating Mechanism
Type 1 Rotary Handle
Breaker Mounted
Red/Yellow Handle
140U-K-RCR
End Cap Kit
Provides 3-phase connections for
terminal or bolt-on connections
Metric Hardware
Qty: 1
140U-K-ECM
Phase Barriers
Provides additional phase clearance when special connections that extend past the circuit
breaker housing are required
Qty: 2
140U-K-PB
1
140U-K-MHM
2
3
4
5
6
7
8
Mounting Hardware
(4) M6 - 1.0 x 45 mm
9
10
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-77
04_140U_400A_K_Frame.qxd
4/23/2008
12:07 PM
Page 2-78
Bulletin 140U
Molded Case Circuit Breakers
Approximate Dimensions — 400 A, K-Frame
Dimensions are in inches (millimeters). Dimensions are not intended to be used for manufacturing purposes.
Front View
Side View
5.490(139.43)
.500
(12.70)
1
.844
(21.44)
1.719
(43.66)
2.813
(71.45)
1.719
(43.66)
2
2.063 (52.39)
.125
(3.18)
4.125 (104.78)
3
.093 R
(2.36) R
3.75
(9.52)
ON
.375
(9.52)
Contact
Position
Indicators
Red/1 - On
Green/O - Off
White - T rip
2.438
(61.89)
.750
(19.05)
CL
10.125
(257.18)
.063
(1.60)
1.063
(27.00)
3.875 R
(98.42) R
Handle
.500
(12.70)
1.219
(30.96)
1.625
(41.28)
1.625
(41.28)
D
.250
(6.35)
1.250
(31.75)
.062
(1.57)
.500
(12.70)
8.438
(214.33)
8.875
(225.43)
OFF
.250 R
(6.35) R
5
43û
4.000
(101.60)
3.563
(90.50)
1.000
(25.40)
3.813
(96.85)
.125 (3.18) Wide x
.750 (19.05) Slots for
Attachment Leads
.188
(4.77) R
7.406
(112.70)
.694
(17.63)
.188 (4.77) Dia.
C'Bore x .031 (.79)
DP .147 (12.7) Dia.
Hole x .500 DP to
Accept #8 (M4)
Thread Cutting
Screws (8 Places)
.860 (21.84)
4.437
(65.10)
.500
(12.70)
Trough for
Attachment
Leads
2.563
(12.70)
4
Line End
.625
(15.88)
C
B
.209
(5.31)
.188
(4.77)
A
1.734
(44.04)
2.391
(60.73)
39û
4.782(121.46)
.698
.547
(13.89) (17.73)
.188 R
(4.77) R
.500
(12.70)
6
1.160
(29.49)
Dimensions for Extended
Terminals and Barrier Style
Nos. 4212B60G02,
4212B61G02 and 1492D24H01
7
.063 (1.60)
.937
(23.80)
8
.875
(22.25)
.438
(11.13)
.250 (6.35) R
1.063
(27.00)
.750 (19.05)
Wide Conductor
with .391 (9.93)
Dia Hole Line
and Load End
3.812
(96.82)
.188
(4.77)
9
.766
(19.46)
2.375
(60.33)
.500
(12.70)
Load End
.281 (7.14) Dia. Mounting Holes
4 Holes for .250-20 (M6) x 1.50
(38) Mounting Screws .500
(12.70) Dia. C'Bore from T op
2.875 (73.03) Deep Load End
2.625 (66.68) Deep Line End .438
(11.13) Dia C'Bore .750 (10.05)
Deep from Bottom
F
Breaker
Status
Dimensions
A
B
C
D
E
F
Handle
Force➀
On
5.39
(136.9)
5.20
(132.1)
5.69
(144.5)
5.61
(142.5)
4.72
(119.9)
4.77
(121.2)
Tripped
4.77
(121.2)
4.69
(119.1)
5.08
(129.0)
5.11
(129.8)
4.89
(124.2)
4.89
(124.2)
N/A
Off
4.16
(105.7)
4.21
(106.9)
4.46
(113.3)
4.64
(117.9)
4.95
(125.7)
4.91
(124.7)
25 lbs.
(11.34 kgs.)
Reset
4.07
(103.4)
4.14
(105.2)
4.57
(116.1)
4.56
(115.8)
4.95
(125.7)
4.90
(124.5)
35 lbs.
(15.87 kgs.)
➀ All handle forces measured approximately 0.125 (3.17) from top of handle.
10
11
12
13
Visit our website: www.ab.com/catalogs
2-78
.062
(1.57)
4.062
(103.17)
E
Preferred availability cat. nos. are printed in bold
30 lbs.
(13.61 kgs.)
5.966(151.54)
.625 (15.88)
6 Holes
4.313
(109.55)
.110 (2.79) Dia. x .297 (7.54)
Deep, 4 Holes Accept #6
(M3) Thread Cutting Screws
3.438
(87.32)
5.000(127.00)
!
5.766(146.46)
!
06_140U_600A_L_Frame.qxd
4/3/2008
11:50 AM
Page 2-79
Bulletin 140U
Molded Case Circuit Breakers
Product Selection — 600 A, L-Frame
y UL 489
y CSA 22.2, No. 5
y IEC 60947-2
y CE
y KEMA-KEUR
!
Note: Terminal box lugs must be ordered separately. See page 2-80
1
2
Breaker Frames
Rated
Current In [A]
220…240V
85
600
Interrupting Rating (60 Hz)
[kA]
Breaking Capacity (50 Hz) Icu /Ics [kA]
380…415V
85
45
525V
45
25
690V
13
20
10
240V
480V
600V
Cat. No.
65
35
25
140U-L3X3
3
100
100
70
70
35
18
25
13
100
65
35
‡
140U-L6X3
200
200
100
100
50
25
30
15
200
100
50
‡
140U-L0X3
4
‡ Current Limiting
Trip Units and Rating Plugs
Thermal-Magnetic
Electronic
Adjustment Range [A]
Thermal Trip
Rated
Current In [A] Ιr = Ιn (Fixed)
5
Adjustment Range [A]
Magnetic Trip
Ιm = 5…10 x Ιn
Cat. No.
250
250
1250…2500
140U-LTD3-D25
300
300
1500…3000
140U-LTD3-D30
350
350
1750…3500
140U-LTD3-D35
400
400
2000…4000
140U-LTD3-D40
500
500
2500…5000
140U-LTD3-D50
600
600
3000…6000
140U-LTD3-D60
Rated
Current In
[A]
250
400
600
Thermal Trip
Ιr = 0.5…1.0 x Ιn
Magnetic Trip
Ιm = 2…10 x Ιn
100…250
200…2500
160…400
320…4000
240…600
480…6000
Protection Type
Cat. No.
LS
140U-LTL3-D25
LSI
140U-LTH3-D25
LSG
140U-LTG3-D25
LSIG
140U-LTI3-D25
LS
140U-LTL3-D40
LSI
140U-LTH3-D40
LSG
140U-LTG3-D40
LSIG
140U-LTI3-D40
LS
140U-LTL3-D60
LSI
140U-LTH3-D60
LSG
140U-LTG3-D60
LSIG
140U-LTI3-D60
6
7
8
Assembled Circuit Breakers, Thermal-Magnetic Trip Units
9
Breaking
Capacity/Interrupting
Rating [kA]7
Breaking
Capacity/Interrupting
Rating [kA]7
Rated Current Thermal Trip
Ιr = Ιn
In [A]
400V
480V
Cat. No.
400V
480V
Cat. No.
140U-L3D3-D25
70
65
140U-L6D3-D25
35
140U-L3D3-D30
70
65
140U-L6D3-D30
35
140U-L3D3-D35
70
65
140U-L6D3-D35
250
250
45
35
300
300
45
350
350
45
400
400
45
35
140U-L3D3-D40
70
65
140U-L6D3-D40
500
500
45
35
140U-L3D3-D50
70
65
140U-L6D3-D50
600
600
45
35
140U-L3D3-D60
70
65
140U-L6D3-D60
10
11
7 Full ratings are found in the breaker frames table on this page
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-79
06_140U_600A_L_Frame.qxd
4/3/2008
11:50 AM
Page 2-80
Bulletin 140U
Molded Case Circuit Breakers
Product Selection — 600 A, L-Frame, Continued
!
!
1
2
Assembled Circuit Breakers, Electronic Trip Units
3
Thermal Trip
Ιr = 0.5…1.0 x Ιn
Rated Current In [A]
LS
4
250
5
100…250
400
6
160…400
600
Breaking Capacity/
Interrupting Rating
[kA]7
Breaking Capacity/
Interrupting Rating
[kA]7
Protection
400V
480V
Type
240…600
45
35
Cat. No.
400V
480V
Cat. No.
140U-L3L3-D25
70
65
140U-L6L3-D25
LSI
45
35
140U-L3H3-D25
70
65
140U-L6H3-D25
LSG
45
35
140U-L3G3-D25
70
65
140U-L6G3-D25
LSIG
45
35
140U-L3I3-D25
70
65
140U-L6I3-D25
LS
45
35
140U-L3L3-D40
70
65
140U-L6L3-D40
LSI
45
35
140U-L3H3-D40
70
65
140U-L6H3-D40
LSG
45
35
140U-L3G3-D40
70
65
140U-L6G3-D40
LSIG
45
35
140U-L3I3-D40
70
65
140U-L6I3-D40
LS
45
35
140U-L3L3-D60
70
65
140U-L6L3-D60
LSI
45
35
140U-L3H3-D60
70
65
140U-L6H3-D60
LSG
45
35
140U-L3G3-D60
70
65
140U-L6G3-D60
LSIG
45
35
140U-L3I3-D60
70
65
140U-L6I3-D60
7 Full ratings are found in the breaker frames table on page 2-79
7
8
Molded Case Switch — UL 489
Rated Current
In [A]
Magnetic Trip
Im = 10 x In [A]
600
6000
Breaking Capacity (50 Hz) Icu /Ics [kA]
220…240V
100
100
380…415V
70
70
Interrupting Rating (60 Hz) [kA]
500V
50
690V
38
25
13
240V
480V
600V
Cat. No.
100
65
35
140U-L6S3-D60
Terminal Lugs
Description
9
Terminal Lugs
10
11
Terminal Lugs
Qty: 3 (includes shield)
140U-L-TL6A1
Copper lug, Cu wire only
(1) 500…750 MCM
or (1) 240…380 mm2
Qty: 3 (includes shield)
140U-L-TL6C1
Aluminum lug, Al or Cu wire
(2) 2…500 MCM
or (2) 35…240 mm2
Qty: 3 (includes shield)
140U-L-TL6A2
Copper lug, Cu wire only
(2) 2…500 MCM
or (2) 35…240 mm2
Qty: 3 (includes shield)
140U-L-TL6C2
Aluminum lug, Al or Cu wire
(1) 2…500 MCM
or (1) 35…240 mm2
Qty: 1
140U-L-TL4A1
Copper lug, Cu wire only
(1) 2…500 MCM
or (1) 35…240 mm2
Qty: 1
140U-L-TL4C1
12
13
Visit our website: www.ab.com/catalogs
2-80
Cat. No.
Aluminum lug, Al or Cu wire
(1) 500…750 MCM
or (1) 240…380 mm2
Preferred availability cat. nos. are printed in bold
06_140U_600A_L_Frame.qxd
4/3/2008
11:51 AM
Page 2-81
Bulletin 140U
Molded Case Circuit Breakers
Accessories — 600 A, L-Frame
Internal Control Modules — Field Installed
Description
Diagram
Auxiliary Contact (AX)
Electrically indicates
"ON/OFF" status of
breakers
Mounting Location
(1) 1a-1b
(2) 1a-1b
Alarm Contact (AL)
Electrically indicates when
the breaker is in the
"TRIPPED" state
Cat. No.
!
140U-H-EA1
Left AND Right side
(1) 1M (make)-1B (break)
140U-H-EA2
140U-J-ER1
1
2
Right side ONLY
3
Auxiliary/Alarm Contact
(AX/AL)
Combination
Combination of auxiliary
contact and alarm contact
(1) 1a-1b
(1) 1M (make)-1B (break)
140U-J-EA1R1
4
Right side ONLY
Shunt Trip (SNT)
Provides remote tripping of
the circuit breaker
Undervoltage trip not
available when shunt trip is
used
Undervoltage Release
(UVT)
Automatically trips breaker
when voltage falls between
preset value, 35…70%
Shunt trip is not available
when undervoltage release
is used
24…60V, 50/60/DC
140U-H-SNJ
110…240V, 50/60/DC
140U-H-SND
380…440V AC, 220…250V
DC
140U-H-SNN
380…600V, 50/60 Hz
Left side ONLY
140U-H-SNB
24V, 50/60 Hz
140U-H-UJ
110…127V, 50/60 Hz
140U-H-UD
208…240V, 50/60 Hz
140U-H-UA
380…500V, 50/60 Hz
140U-H-UB
525…600V, 50/60 Hz
Left side ONLY
5
140U-H-UC
6
7
Note: For Factory-Installed internal control modules, please see page 2-92
8
9
10
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-81
06_140U_600A_L_Frame.qxd
4/3/2008
11:53 AM
Page 2-82
Bulletin 140U
Molded Case Circuit Breakers
Accessories — 600 A, L-Frame, Continued
External Accessories
!
Description
!
Cat. No.
Terminal Shields
IP20 Ingress Protection Rating
1
140U-L-TS
Flex-Cable Operating Mechanism
Includes handle, cable, operating, and bail mechanism
Pre-assembled and adjusted
UL Type 1/3/12/4/4X
Flange-Mount Operating Handle
Non-Metallic
2
Flex-Cable Operating Mechanism
Includes handle, cable, operating, and bail mechanism
Pre-assembled and adjusted
UL Type 4/4X
Flange-Mount Operating Handle
Stainless Steel
3
Rotary, Variable-Depth Operating Mechanism
UL Type 3/12/4/4X, IP 66 Rotary handle
12 in. (30.48 cm) operating rod
4
Rotary, Variable-Depth Operating Mechanism
UL Type 3/12/4/4X, IP 66 Rotary handle
21 in. (53.34 cm) operating rod
5
6
8
10
4 ft (1.2 m) Cable
140U-L-FCS04
6 ft (1.9 m) Cable
140U-L-FCS06
10 ft (3.0 m) Cable
140U-L-FCS10
Black Handle
140U-L-RVM12B
Red/Yellow Handle
140U-L-RVM12R
Black Handle
140U-L-RVM21B
Red/Yellow Handle
140U-L-RVM21R
Black Handle
140U-L-NVM12B
Red/Yellow Handle
140U-L-NVM12R
Black Handle
140U-L-NVM21B
Red/Yellow Handle
140U-L-NVM21R
140U-L-RMX
End Cap Kit
Provides 3-phase connections for terminal or bolt-on connections
Metric hardware provided
Qty: 1
140U-L-ECM
Phase Barriers
Provides additional phase clearance when special connections that extend past the circuit
breaker housing are required
Qty: 2
140U-K-PB
400 A
For use with LFrame 3-pole
MCCBs up to 400 A
140U-L-GFP4003
600 A
For use with LFrame 3-pole
MCCBs up to 600 A
140U-L-GFP6003
For use with 3- or 4Pole MCCBs,
110…240V AC/DC
140U-L-EOPD
For use with 3- or 4Pole MCCBs, 24V
DC
140U-L-EOPZ
For use with 3- or 4Pole MCCBs
140U-L-MHM
Mounting Hardware
(4) M5 - 0.8 x 100 mm
12
13
Visit our website: www.ab.com/catalogs
2-82
140U-L-FCX10
Black Handle
Motor Operator
Remotely opens, closes, and resets the circuit breaker
110…240V AC
11
10 ft (3.0 m) Cable
Rotary, Variable-Depth Operating Mechanism with Internal NFPA79 Operating Handle
UL Type 3/12/4/4X, IP 66 Rotary Handle
21 in. (53.34 cm) operating rod
Ground Fault Leakage Module
Current pickup settings are selectable from 0.03…30 A with time delays up to1.0 s.
Time delays are also selectable from Instantaneous…1.0 s for 0.10 A settings and
above. A current pickup setting of 0.03 A defaults to an Instantaneous time setting
regardless of the time dial’s position. Two alarm contacts come as standard: a 50%
pretrip and a 100% after trip contact, both based only on earth leakage current
levels.
9
140U-L-FCX04
140U-L-FCX06
Rotary, Variable-Depth Operating Mechanism with Internal NFPA79 Operating Handle
UL Type 3/12/4/4X, IP 66 Rotary Handle
12 in. (30.48 cm) operating rod
Rotary, Direct Couple Operating Mechanism
Breaker Mounted
7
4 ft (1.3 m) Cable
6 ft (1.9 m) Cable
Preferred availability cat. nos. are printed in bold
06_140U_600A_L_Frame.qxd
4/3/2008
11:53 AM
Page 2-83
Bulletin 140U
Molded Case Circuit Breakers
Approximate Dimensions — 600 A, L-Frame
Dimensions are in inches (millimeters). Dimensions are not intended to be used for manufacturing purposes.
5.48
[ 139,2
!
]
1.72
[ 43,6 ]
3.36
[ 85,3 ]
Ø.22
[ 5,5 ]
1
2
3
10.13
[ 257,2
8.44
[ 214,4
]
4
]
5
6
1.72
[ 43,7 ]
7
1.72
[ 43,7 ]
5.43
[ 137,9
]
8
9
10
.25
[ 6,4 ]
.97
[ 24,6 ]
11
1.34
[ 34,1 ]
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-83
07_140U_800A_M_Frame.qxd
4/23/2008
11:37 AM
Page 2-84
Bulletin 140U
Molded Case Circuit Breakers
Product Selection — 800 A, M-Frame
!
!
y UL 489
y CSA 22.2, No. 5
y IEC 60947-2
y CE
y KEMA-KEUR
1
Breaker Frames
Breaking Capacity (50 Hz) Icu /Ics [kA]
Rated
Current In [A]
2
Note: Terminal box lugs must be ordered separately. See page 2-86
220…240V
800
380…415V
Interrupting Rating (60 Hz) [kA]
525V
690V
240V
480V
600V
Cat. No.
65
65
50
50
50
25
20
10
65
50
25
140U-M5X3
100
100
70
70
70
50
25
13
100
65
35
140U-M6X3
Trip Units and Rating Plugs
3
4
5
Thermal-Magnetic
Electronic
Adjustment Range [A]
Adjustment Range [A]
Rated
Current In
[A]
Thermal Trip
Ιr = Ιn
Magnetic Trip
Ιm = 5…10 x Ιn
Cat. No.
300
300
1500…3000
140U-MTD3-D30
350
350
1750…3500
140U-MTD3-D35
400
400
2000…4000
140U-MTD3-D40
450
450
2250…4500
140U-MTD3-D45
500
500
2500…5000
140U-MTD3-D50
600
600
3000…6000
140U-MTD3-D60
700
700
3500…7000
140U-MTD3-D70
800
800
4000…8000
140U-MTD3-D80
Rated
Current In
[A]
800A
Thermal Trip
Ir = 0.5…
1.0 x In
Magnetic Trip
Im = 2…8 x In
400…8009
800…6400
Cat. No.
400…800 A
LS Electronic
Trip Unit
140U-MTL3-D80
400…800 A
LSI Electronic
Trip Unit
140U-MTH3-D80
400…800 A
LSG Electronic 140U-MTG3-D80
Trip Unit
400…800 A
LSIG Electronic 140U-MTI3-D80
Trip Unit
Rating Plugs
6
Protection
Type
Thermal Trip
In [A]
Cat. No.
Thermal Trip
In [A]
Cat. No.
400
140U-MRP3-D40
700
140U-MRP3-D70
500
140U-MRP3-D50
800
140U-MRP3-D80
600
140U-MRP3-D60
—
—
7
Assembled Circuit Breakers, Thermal-Magnetic Trip Units
8
Rated Current In [A]
Thermal Trip
Ιr = Ιn
300
300
9
10
11
400V
480V
Cat. No.
400V
480V
Cat. No.
50
50
140U-M5D3-D30
70
65
140U-M6D3-D30
350
350
50
50
140U-M5D3-D35
70
65
140U-M6D3-D35
400
400
50
50
140U-M5D3-D40
70
65
140U-M6D3-D40
450
450
50
50
140U-M5D3-D45
70
65
140U-M6D3-D45
500
500
50
50
140U-M5D3-D50
70
65
140U-M6D3-D50
600
600
50
50
140U-M5D3-D60
70
65
140U-M6D3-D60
700
700
50
50
140U-M5D3-D70
70
65
140U-M6D3-D70
800
800
50
50
140U-M5D3-D80
70
65
140U-M6D3-D80
7 Full ratings are found in the breaker frames table on this page
Assembled Circuit Breakers, Electronic Trip Units
Breaking Capacity/
Interrupting Rating [kA]7
Breaking Capacity/
Interrupting Rating [kA]7
Thermal Trip
Rated
Current In [A] Ιr = 0.5…1.0 x Ιn
12
Breaking
Capacity/Interrupting Rating
[kA]7
Breaking
Capacity/Interrupting Rating
[kA]7
800
200…8009
Protection
Type
400V
480V
Cat. No.
400V
480V
Cat. No.
LS
50
50
140U-M5L3-D80
70
65
140U-M6L3-D80
LSI
50
50
140U-M5H3-D80
70
65
140U-M6H3-D80
LSG
50
50
140U-M5G3-D80
70
65
140U-M6G3-D80
9 Select proper rating plug to cover thermal trip requirement.
13
7 Full ratings are found in the breaker frames table on this page
Visit our website: www.ab.com/catalogs
2-84
Preferred availability cat. nos. are printed in bold
07_140U_800A_M_Frame.qxd
4/23/2008
11:37 AM
Page 2-85
Bulletin 140U
Molded Case Circuit Breakers
Product Selection, Continued/Accessories — 800 A, M-Frame
Molded Case Switch — UL 489
Rated
Current In [A]
Magnetic Trip [A]
Im = 10 x In
800
8000
Breaking Capacity (50 Hz) Icu /Ics [kA]
220…240V
380…415V
100
70
100
70
500V
70
50
Interrupting Rating (60 Hz) [kA]
690V
25
240V
480V
600V
Cat. No.
100
65
35
140U-M6S3-D80
13
!
1
Αχχεσσοριεσ
Internal Control Modules — Field Installed
Description
Auxiliary Contact (AX)
Electrically indicates
"ON/OFF" status of
breakers
Mounting Location
(1) 1a-1b
(2) 1a-1b
Alarm Contact (AL)
Electrically indicates
when the breaker is in
the "TRIPPED" state
Diagram
Cat. No.
140U-M-EA1
Left AND Right Side
(1) 1M (make)-1B (break)
140U-M-EA2
3
140U-M-ER1
4
Right Side Only
Auxiliary/Alarm Contact
(AX/AL)
Combination
Combination of auxiliary
contact and alarm
contact
2
140U-MEA1R1
(1) 1a-1b
(1) 1M (make)-1B (break)
5
Right Side Only
6
Shunt Trip (SNT)
Provides remote tripping
of the circuit breaker
Undervoltage trip not
available when shunt trip
is used
Undervoltage Release
(UVT)
Automatically trips
breaker when voltage
falls between preset
value, 35…70%
Shunt trip is not available
when undervoltage
release is used
12…24V, 50/60/DC
140U-M-SNJ
110…240V AC,
110…125V DC
140U-M-SND
380…440V AC,
220…250V DC
480…600V, 50/60 Hz
140U-M-SNN
Left Side Only
24V, 50/60 Hz
140U-M-UJ
110…127V, 50/60 Hz
140U-M-UD
208…240V, 50/60 Hz
140U-M-UA
380…500V, 50/60 Hz
Left Side Only
7
140U-M-SNB
8
140U-M-UB
9
10
11
12
Note: For Factory-Installed internal control modules, please see page 2-92
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-85
07_140U_800A_M_Frame.qxd
4/23/2008
11:38 AM
Page 2-86
Bulletin 140U
Molded Case Circuit Breakers
Accessories — 800 A, M-Frame, Continued
External Accessories
!
Description
!
Flex-Cable Operating Mechanism
Includes handle, cable, operating, and bail mechanism
Pre-assembled and adjusted
UL Type 1/3/12/4/4X
Flange-Mount Operating Handle
Non-Metallic
1
Flex-Cable Operating Mechanism
Includes handle, cable, operating, and bail mechanism
Pre-assembled and adjusted
UL Type 4/4X
Flange-Mount Operating Handle
Stainless Steel
2
Rotary, Variable-Depth Operating Mechanism
UL Type 3/12/4/4X, IP 66 Rotary Handle
12 in. (30.48 cm) operating rod
Rotary, Variable-Depth Operating Mechanism
UL Type 3/12/4/4X, IP 66 Rotary Handle
21 in. (53.34 cm) operating rod
3
140U-M-FCX06
10 ft (3.0 m) Cable
140U-M-FCX10
4 ft (1.3 m) Cable
140U-M-FCS04
6 ft (1.8 m) Cable
140U-M-FCS06
10 ft (3.0 m) Cable
140U-M-FCS10
Black Handle
140U-M-RVM12B
Red/Yellow Handle
140U-M-RVM12R
Black Handle
140U-M-RVM21B
140U-M-RVM21R
140U-M-NVM12B
Red/Yellow Handle
140U-M-NVM12R
Black Handle
140U-M-NVM21B
Red/Yellow Handle
140U-M-NVM21R
Copper lug, Cu wire Only
(3) 3/0…300 MCM
or (3) 95…135 mm2
Qty: 1
140U-M-TLC3
Aluminum lug, Al or Cu wire
(3) 3/0…400 MCM
or (3) 95…185 mm2
Qty: 1
140U-M-TLA3
Aluminum lug, Al or Cu wire
(2) 1…500 MCM
or (2) 50…240 mm2
Qty: 1
140U-M-TLA2
Aluminum lug, Al or Cu wire
(2) 500…750 MCM
or (2) 240…400 mm2
Qty: 1
140U-M-TLA2A
Copper lug, Cu wire only
(2) 2/0…500 MCM
or (2) 70…240 mm2
Qty: 1
140U-M-TLC2
Phase Barriers
Provides additional phase clearance when special connections that
extend past the circuit breaker housing are required
Qty: 2
140U-M-PB
Padlock Kit
Padlocking Hasp
Lock-OFF only
Qty: 1
140U-M-PL
For use with 3- or 4-Pole
MCCBs
140U-M-MHM
Terminal Lugs
6
Terminal Lugs
7
6 ft (1.8 m) Cable
Black Handle
Rotary, Variable-Depth Operating Mechanism with Internal
NFPA79 Operating Handle
UL Type 3/12/4/4X, IP 66 Rotary Handle
21 in. (53.34 cm) operating rod
5
140U-M-FCX04
Red/Yellow Handle
Rotary, Variable-Depth Operating Mechanism with Internal
NFPA79 Operating Handle
UL Type 3/12/4/4X, IP 66 Rotary Handle
12 in. (30.48 cm) operating rod
4
Cat. No.
4 ft (1.3 m) Cable
8
9
10
Mounting Hardware
(4) M8 - 1 x 35 mm
11
12
13
Visit our website: www.ab.com/catalogs
2-86
Preferred availability cat. nos. are printed in bold
07_140U_800A_M_Frame.qxd
4/23/2008
11:38 AM
Page 2-87
Bulletin 140U
Molded Case Circuit Breakers
Approximate Dimensions — 800 A, M-Frame
Αππροξιματε Διμενσιονσ
Dimensions are in inches (millimeters). Dimensions are not intended to be used for manufacturing purposes.
!
C
L
Handle
Pivot
Line End
2.018
(51.26)
.375 (9.53) Dia. 4-Holes for .312 (7.92) 16 (406.40) x 1.75 (44.45) Large Mounting Screws.
.500
(12.70)
1.411
(35.84)
Max.
.547
(13.89)
1
2
8.302
(210.87)
7.677
(195.00)
6.052
(153.72)
On/I
.415
(10.54)
3
Tripped
0.2û
11.500
(292.10)
On/I
On
14.7û
C
L
Handle
Pivot
14.750
(374.65)
4
Off
19.2û
Off/O
Off/O
Reset
24.2û
16.000
(406.40)
5
Dim.
B
Dim.
A
6
1.375
(34.93)
.500 (12.70) - 13 Tap
Thru.
.500
(12.70)
2.750
(69.85)
.531
(13.49)
2.531
(64.29)
7
4.062
(103.17)
2.750
(69.85)
5.500
(139.70)
4.375
(111.13)
4.250
(107.95)
8.250
(209.55)
Load End
3.250
(82.55)
1.625
(41.28)
1.625
(41.28)
.813
(20.65)
1.874
(47.60)
Breaker Status
Dimension A
8
Dimension B
On
8.72
(221.49)
9.17
(232.92)
Off
6.72
(170.69)
7.14
(181.36)
Tripped
7.86
(199.64)
8.30
(210.82)
Reset
6.44
(163.58)
6.84
(173.74)
9
10
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-87
08_140U_1200A_N_Frame.qxd
4/3/2008
3:21 PM
Page 2-88
Bulletin 140U
Molded Case Circuit Breakers
Product Selection — 1200 A, N-Frame
!
!
y UL 489
y CSA 22.2, No. 5
y IEC 60947-2
y CE
y KEMA-KEUR
1
Assembled Circuit Breakers, Electronic Trip Units
Note: Terminal box lugs must be ordered separately. See page 2-90
Adjustment Range Ir [A]
2
Rated
Current
In [A]
1200
1200
Thermal Trip
Ir = 0.5…1.0 x In
600…12009
600…1200
Breaking Capacity (50 Hz)
Magnetic Trip
Im = 2…8 x In
4
600…12009
220…240V 380…415V
LS
1200…10600
1200…10600
3
1200
Icu /Ics [kA]
Protection
Type
1200…10600
85
85
50
50
Interrupting Rating (60 Hz) [kA]
500V
40
20
690V
20
10
240V
480V
600V
Cat. No.
65
50
25
140U-N5L3-E12
LS
100
100
70
50
50
25
25
13
100
65
35
140U-N6L3-E12
LSI
100
100
70
50
50
25
25
13
100
65
35
140U-N6H3-E12
140U-N6G3-E12
LSG
100
100
70
50
50
25
25
13
100
65
35
LSIG
100
100
70
50
50
25
25
13
100
65
35
140U-N6I3-E12
LS
200
100
100
50
65
33
35
18
200
100
50
140U-N0L3-E12
LSI
200
100
100
50
65
33
35
18
200
100
50
140U-N0H3-E12
LSG
200
100
100
50
65
33
35
18
200
100
50
140U-N0G3-E12
LSIG
200
100
100
50
65
33
35
18
200
100
50
140U-N0I3-E12
9 Select proper rating plug to cover thermal trip equipment.
Rating Plugs
Rated Current
In [A]
Cat. No.
Rated
Operational
Current
In [A]
600
140U-NRP3-D60
900
140U-NRP3-D90
700
140U-NRP3-D70
1000
140U-NRP3-E10
800
140U-NRP3-D80
1200
140U-NRP3-E12
5
6
Cat. No.
Molded Case Switch — UL 489
7
Breaking Capacity (50 Hz) Ιcu /Ιcs [kA]
Magnetic Trip
Rated
10 x Ιn
Current In [A]
1200
12000
220…240V
100
100
380…415V
70
50
500V
50
Interrupting Rating (60 Hz) [kA]
690V
25
25
13
240V
100
8
9
10
11
12
13
Visit our website: www.ab.com/catalogs
2-88
Preferred availability cat. nos. are printed in bold
480V
65
600V
35
Cat. No.
140U-N6S3-E12
08_140U_1200A_N_Frame.qxd
4/3/2008
3:21 PM
Page 2-89
Bulletin 140U
Molded Case Circuit Breakers
Accessories — 1200 A, N-Frame
Internal Control Modules — Field Installed
Description
Auxiliary Contact (AX)
Electrically indicates
"ON/OFF" status of
breakers
Mounting Location
(1) 1a-1b
(2) 1a-1b
Alarm Contact (AL)
Electrically indicates
when the breaker is in
the "TRIPPED" state
Diagram
Cat. No.
!
140U-N-EA1
Left AND Right side
140U-N-EA2
140U-N-ER1
(1) 1M (make)-1B (break)
1
2
Right side ONLY
Auxiliary/Alarm Contact
(AX/AL)
Combination
Combination of auxiliary
contact and alarm
contact
Shunt Trip (SNT)
Provides remote tripping
of the circuit breaker
Undervoltage trip not
available when shunt trip
is used
Undervoltage Release
(UVT)
Automatically trips
breaker when voltage
falls between preset
value, 35…70%
Shunt trip is not available
when undervoltage
release is used
3
(1) 1a-1b
(1) 1M (make)-1B (break)
140U-NEA1R1
4
Right side ONLY
12…24V, 50/60/DC
140U-N-SNJ
110…240V AC,
110…125V DC
140U-N-SND
380…440V AC,
220…250V DC
140U-N-SNN
480…600V, 50/60 Hz
Left side ONLY
140U-N-SNB
24V, 50/60 Hz
140U-N-UJ
110…127V, 50/60 Hz
140U-N-UD
208…240V, 50/60 Hz
140U-N-UA
380…500V, 50/60 Hz
Left side ONLY
5
140U-N-UB
Note: For Factory-Installed internal control modules, please see page 2-92
6
7
8
9
10
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-89
08_140U_1200A_N_Frame.qxd
4/3/2008
3:22 PM
Page 2-90
Bulletin 140U
Molded Case Circuit Breakers
Accessories — 1200 A, N-Frame, Continued
External Accessories
!
Description
!
Cat. No.
4 ft. (1.2 m) Cable
140U-N-FCX04
6 ft. (1.9 m) Cable
140U-N-FCX06
10 ft. (3.0 m) Cable
140U-N-FCX10
Black Handle
140U-N-RM12B
Phase Barriers
Provides additional phase clearance when
special connections that extend past the
circuit breaker housing are required
Qty: 2
140U-N-PB
Padlock Kit
Padlocking Hasp
Lock-OFF only
Qty: 1
140U-N-PL
Motor Operator
Remotely opens, closes, and resets the
circuit breaker
110…240V AC
Qty: 1
140U-N-EOPD
7
Motor Operator, 230..240V AC
Qty: 1
140U-N-EOPA
8
Mounting Hardware
(4) M8 - 1 x 35 mm
For use with 3- or 4-Pole MCCBs
140U-M-MHM
Flex-Cable Operating Mechanism
NEMA Type 1/3/12/4/4X
Flange-Mount Handle
1
2
Rotary, Variable-Depth Operating
Mechanism
Type 1/12 Rotary Handle
12 in. (30.48 cm) operating rod
3
4
5
6
Terminal Lugs
9
Description
10
11
Terminal Lugs
12
13
Pkg. Quantity
Cat. No.
Aluminum lug, Al or Cu wire
(2) 1…500 MCM
or (2) 50…240 mm2
Qty: 1
140U-N-TLA2
Aluminum lug, Al or Cu wire
(3) 3/0…400 MCM
or (3) 95…185 mm2
Qty: 1
140U-N-TLA3
Aluminum lug, Al or Cu wire
(4) 4/0…500 MCM
or (4) 120…300 mm2
Qty: 1
140U-N-TLA4
Aluminum lug, Al or Cu wire
(3) 500…750 MCM
or (3) 300…400 mm2
Qty: 1
140U-N-TLA3A
Copper lug, Cu wire only
(2) 2/0…500 MCM
or (2) 70…240 mm2
Qty: 1
140U-N-TLC2
Copper lug, Cu wire only
(3) 3/0…500 MCM
or (3) 95…240 mm2
Qty: 1
140U-N-TLC3
Copper lug, Cu wire only
(4) 3/0…400 MCM
or (4) 95…185 mm2
Qty: 1
140U-N-TLC4
Visit our website: www.ab.com/catalogs
2-90
Preferred availability cat. nos. are printed in bold
08_140U_1200A_N_Frame.qxd
4/3/2008
3:22 PM
Page 2-91
Bulletin 140U
Molded Case Circuit Breakers
Approximate Dimensions — 1200 A, N-Frame
Dimensions are in inches (millimeters). Dimensions are not intended to be used for manufacturing purposes.
Removable T erminal
Cover Must Be in
Place While in Service
!
.344 (8.738) Dia. Mounting Holes
.703 (17.856) Dia. C'Bore
4.453 (113.106) Deep from Top
.594 (15.088) Dia C'Bore
.359 (9.119) Deep from Bottom
1.062 (26.987)
.531 (13.481)
1.157(29.388)
.532(13.513)
.500-13 (12 X 1.75) Tap
12-Holes
1
.062 (1.575)
Line End
3.236
(82.194)
Trough for
Attachment Lead
.250 R
(6.350) R
7.000 (177.774)
9.250 (234.950)
14.750(374.650)
8.625(219.075)
115.00 (292.075)
11.431
(290.348)
.062 R
(1.575) R
.094 R
(2.388) R
.297
(7.544)
2
.125 X .750
(3.175 X 19.050)
Slots for
Attachment Leads
3.850 R
3
21û±2û
ON/I
ON
.353
(6.331)
0û±2û
TRIPPED
15û±2û
.946
(24.022)
.750(19.050)
.375(9.525)
OFF/O
.188R
(4.762)R
2.511
(63.786)
1.375
(34.925)
2.750
(69.850)
2.344
3.187
(59.541)
(80.950)
6.375
(161.925)
4.124
(104.750)
.062 (1.575)
.532 (13.513)
1.095(27.813)
3.344 (84.938)
5.188(131.769)
2.750 Ref.
(69.850) Ref.
2.000
(50.800)
1.000
(25.400)
Breaker Status
6.000(152.400)
A
B
On
7.90 (200.66)
8.30 (210.82)
Tripped
6.50 (165.10)
6.90 (175.26)
Off
5.70 (144.78)
6.10 (154.94)
Reset
5.60 (142.24)
6.00 (152.40)
7.132(181.146)
Handle Forces (At Handle C)L
3.906
(99.187)
On
130 lbs. (58.97 kgs.)
Off
105 lbs. (47.63 kgs.)
Reset
160 lbs. (72.57 kgs.)
1.500 Ref
(38.100) Ref
7
8
3.819
(96.723)
4.875
(123.799)
.062
(1.575)
6
5.500(139.687)
Dimensions
.781 (19.844)
.062
(1.588)
R
Load End
5.248(133.293)
1.688
(42.863)
.062
(1.588)
R
5
Removable Terminal
Cover Must Be in
Place While in Service
3.375
(85.725)
1.562
(39.687)
4
1.034
(33.281)
Handle
Pivot
Contact Position Indicator
Red-I/ON
Green-O/OFF
White-TRIPPED
8.250
(209.550)
2.000
(50.800)
2.982
(75.743)
B A
.147 (3.734) Dia. Hole
.500 (12.70) Deep to
Accept a #8Thread
Cutting Screw
6-Places
3.808
(96.723)
2.798
(71.057)
.375
(9.525)
RESET
1.500
(38.100)
.312 R
(7.925)R
13û±2ûOFF
CL Push To Trip
16.000 (406.401)
CL Handle
For 2-Pole Breaker Omit Current
Carrying Parts from Center Pole
9
2.493
(63.792)
6.375 Ref
(161.925) Ref
10
11
12
13
Visit our website: www.ab.com/catalogs
Preferred availability cat. nos. are printed in bold
2-91
09_140U_mods.qxd
4/23/2008
11:54 AM
Page 2-92
Bulletin 140U
Molded Case Circuit Breakers
Factory-Installed Modifications
Internal Control Modules — Factory Installed
For use with G-Frame Molded Case Circuit Breakers
!
2-Pole Breaker
Mounting Location
Left side only
Right side only
1
(1) Auxiliary contact (AX)
2
3
4
5
6
3-Pole Breaker
Mounting Location
Left side only
Right side only
(1) Auxiliary contact (AX)
or
(1) Alarm contact (AL)
or
(1) Alarm contact (AL) + Auxiliary contact (AX)
Auxiliary
and
Alarm
Contacts
2-Pole
3-Pole
(1) AX
-A
-A
(1) Shunt Trip (SNT)
or
(1) Undervoltage Release (UVT)
Suffix
Internal Control Modules — Factory Installed
For use with H-, J-, K-, L-, M-, and N-Frame Molded Case Circuit Breakers
Mounting Location
7
8
9
10
Left side only
Right side only
(1) Shunt Trip (SNT)
or
(1) Undervoltage Release (UVT)
(1) Auxiliary contact (AX)
or
(2) Auxiliary contacts (AX)
or
(1) Alarm contact (AL)
or
(1) Alarm contact (AL) + Auxiliary contact (AX)
Auxiliary and
Alarm
Contacts
-A
(2) AX
-B
(1) AX + (1)
AL
Suffix
Shunt Trip Combinations
(1) UVT only
- G⊗
(1) SNT only
- P⊗
(1) AX + (1) UVT
- H⊗
(1) AX + (1) SNT
- Q⊗
- R⊗
Suffix
(1) AX
(1) AL
Undervoltage Release Combinations
-D
-F
(2) AX + (1) UVT
- J⊗
(2) AX + (1) SNT
(1) AX + (1) AL + (1) UVT
- L⊗
(1) AX + (1) AL + (1) SNT
- T⊗
(1) AL + (1) UVT
- N⊗
(1) AL + (1) SNT
- V⊗
⊗Standard Voltage Suffix Codes9
Voltage [V]
11
24
⊗Standard Voltage Suffix Codes9
110…127 208…240 380…480
Voltage [V]
12…24
110…240
380…600
J
D
B
AC,
50/60 Hz
J
D
A
B
AC,
50/60 Hz
Voltage [V]
—
—
—
—
Voltage [V]
12…24
110…125
—
DC
—
—
—
—
DC
J
D
—
12
9 For additional voltages, consult your local
Rockwell Automation sales office or
Allen-Bradley distributor.
13
Visit our website: www.ab.com/catalogs
2-92
Suffix
Preferred availability cat. nos. are printed in bold