Instructions - Go Industries, Inc.

advertisement
Enforcement Series
Grille Guard
Installation Instructions
38017 / 39017 / 40017
420 N. Grove, Richardson, TX 75081
Tele: (800) 527 - 4345 Fax: (800) 442 - 5263
Web site: www.goindustries.com
E-mail: [email protected]
38017
Dodge Charger ‘15
39017
40017
Parts List:
1 - Police Grille
Guard
1 - Driver Bracket
#38017-5
1 - Pass. Bracket
#38017-6
6 - 1/2” x 1 1/2”
Diagram 1
Diagram 2
Bolts
6 - 1/2” Hex Nuts
6 - 1/2” Lock
Washers
12 - 1/2” Flat
Washers
Diagram 3
Note: Completely read instructions before beginning installation!
1. Remove the contents from the box and check for missing pieces or damage. If parts are missing or damaged, contact the original place of purchase.
2. Remove the bumper cover by following the steps listed below:
A. Remove the plastic push clips on top to free the upper section of the bumper cover.
B. Remove the hex bolts from the bottom of the bumper.
C. Remove the push clips on each side that attach the bumper to the inner fender.
D. Remove the hex bolts in the lower front wheel well area.
E. Remove the factory hex bolts on both sides that hold the bumper cover to the fender. To access and remove the hex nut you will need to push aside the inner fender.
F. Unplug the side marker lamp.
G. With the help of another person slowly pull the bumper cover off and be careful not to damage the cover.
3. Once the bumper reinforcement is exposed, remove the (8) factory bolts that hold the bumper reinforcement to the crash canister. Once the (8)
factory bolts are removed, drill out the spot welds above and below the bumper reinforcement on each side. Diagram 4,5 & 7. Use a pry bar to separate
the bumper reinforcement from the crash canister enough to slide the bracket in between the bumper reinforcement and the crash canister as seen
in Diagrams 3 and 4. Please note that the plastic air deflector will need to be trimmed for bracket clearance. Reference Diagrams 4 and 5 for areas to
trim. Make sure the bracket is lined up with the (2) holes on the bumper frame and replace the (8) factory bolts as shown in Diagram 6 (Page 2). The
mounting holes in the brackets are slotted for up and down for adjustability. It is recommended for initial fitting to place the brackets in the furthest
upward position and make adjustments if needed.
Passenger view of air deflector trimming
Driver view of air deflector trimming
Area to trim
Drill Weld
Bum
Reinfo per
rceme
nt
Pry apart
Diagram 4
Page 1 of 2 pages 01/15
Drill Weld
Pry apart
Area to trim
per
Bum ment
force
Rein
Diagram 5
Thank you for choosing Go Industries’ products. For additional installation
assistance, please call Technical Support (800) 527-4345 or (972) 783-7444
Enforcement Series
Grille Guard
Installation Instructions
38017 /39017 / 40017
420 N. Grove, Richardson, TX 75081
Tele: (800) 527 - 4345 Fax: (800) 442 - 5263
Web site: www.goindustries.com
E-mail: [email protected]
Dodge Charger ‘15
Front View of Brackets Installed
Pass. Side
bracket #
38017-6
Driver side
bracket #
38017-5
Factory Bolts
Bumper
Reinforcement
Diagram 6
4. Bumper cover will need to be trimmed. Measurements and areas to be trimmed are shown below in Diagram 7.
5. Test fit the bumper cover to make sure it fits on the brackets and then tighten the factory bolts while holding the brackets in place.
6. Make sure all of the bolts and plastic rivets are reinstalled on the bumper cover before installing grille guard.
7. Grille Guard must be set on top of brackets for installation. Align holes in guard with holes in brackets and install at this time. Use (1) 1/2” x 1 1/2” Bolt
with (2) 1/2” Flat Washers, (1) 1/2” Lock Washer and (1) 1/2” Hex Nut per hole in grille guard. Center guard on vehicle and tighten all bolts at this time.
Bumper Cover upper area to trim measurements
Bumper Cover lower area to trim measurements
Drill Weld and
seperate
5”
2”
Diagram 7
Page 2 of 2 pages 01/15
Diagram 8
Thank you for choosing Go Industries’ products. For additional installation
assistance, please call Technical Support (800) 527-4345 or (972) 783-7444
Download