2015 IEEE International Conference on
Applied Superconductivity and
Electromagnetic Devices
(ASEMD2015)
November 20-23, 2015
November 20-23, 2015
Shanghai, China
Shanghai, China
Sponsor：
IEEE Beijing
Co-Sponsors: Shanghai University
Tianjin University
Organizers:
Shanghai University
Shanghai Key Laboratory for High Temperature Superconductors
Shanghai Creative Superconductor Technology Co. Ltd.
Tianjin University
ASEMD2015
Shanghai, China
Nov.20-23, 2015
2015 IEEE International Conference on
Applied Superconductivity and Electromagnetic Devices
(ASEMD2015)
20-23 November 2015, Shanghai, China
http://www.asemd.org
Program Book
1
ASEMD2015
Shanghai, China
Nov.20-23, 2015
Welcome
Dear Authors and Participants:
It is a great pleasure for us to welcome all of you here in Shanghai to attend the 2015 International Conference
on Applied Superconductivity and Electromagnetic Devices (ASEMD 2015). The ASEMD 2015 conference is sponsored
by the IEEE through Beijing Section, with co-sponsors and principal organizers of Shanghai University, Tianjin
University, and Shanghai Creative Superconductor Technologies Co. Ltd., with contributions from institutes and
industrial partners involved. This innovative and unparalleled conference aims to provide a forum for both
researchers and engineers in the named fields to present and share their new concepts, novel techniques, and the
best existing practices, in order to address key research and technological challenges faced in practical applications. It
places particular emphasis on creating a new platform for scientific and technological development in the fields of
applied superconductivity and electromagnetism, especially in the practical development of novel electromagnetic
device technologies. The Platform gathers University, research institute and industry together; so as to bring theory,
technology and application. Eleven plenary talks are assigned to address the ASEMD 2015 representative fields.
The ASEMD 2015 committee members have worked tirelessly to maintain this platform, and to ensure that the
attendees receive adequate service and substantial benefit from the conference. The committee is looking forward to
seeing your active participation and involvement. On behalf of the ASEMD 2015 committee and organizers, we highly
appreciate the valuable efforts of all the attendees and the rigorous journeys undertook to achieve this. During the
conference, we hope that you will find intellectual stimulation and enjoyment in the planned activities, engage in
exchanging scientific and technological ideas, and develop collaborative relationships. The success of this conference
will depend on the involvement and contributions of all the authors and participants. For good, better and best, has
been marked on the journey path of the ASEMD voyage, which is again what we are forward. We highly appreciated
your supports to this conference, and looking forward to maintaining support in the upcoming ASEMD conferences as
its esteemed members. A warm welcome and many thanks for your assisting in the ASEMD 2015. We hope you will
enjoy your time at the conference, as well as in Shanghai, the most beautiful and modern city in China.
Conference Committee, IEEE ASEMD 2015
2
ASEMD2015
Shanghai, China
Nov.20-23, 2015
Table of Contents
00
Welcome
General Information -------------------------------------------------------------- 4
Background ------------------------------------------------------------------------------- 4
Conference Organization -------------------------------------------------------------- 5
Conference Venue and Transportation --------------------------------------- 6
Venue Information ---------------------------------------------------------------------- 6
Transportation and hotels ------------------------------------------------------------- 6
Registration and Key Reminders ----------------------------------------------14
Registration and Payment ----------------------------------------------------------- 14
Information for Presenters ---------------------------------------------------------- 15
Guidelines for Oral Presentation ---------------------------------------------16
Instructions for Session Chairs ------------------------------------------------17
Conference Program -------------------------------------------------------------18
Program Overview -------------------------------------------------------------------- 18
Plenary and Selected Invited Speeches ------------------------------------------ 21
Technical Program--------------------------------------------------------------------- 30
Plenary Sessions -------------------------------------------------------- 32
Invited and Oral Talks -------------------------------------------------- 33
Poster Sessions ---------------------------------------------------------- 48
HTS Application Workshop ------------------------------------------- 69
Author Index -----------------------------------------------------------------------71
Exhibitions
3
ASEMD2015
Shanghai, China
Nov.20-23, 2015
General Information
01
Background
International
Superconductivity
Conference
and
on
Electromagnetic
Applied
rotating machines, and magnet technology are essential
Devices
components comprising one principal part of the
(ASEMD2015) will be held from 20 to 23 November
2015 in Shanghai. ASEMD2015 is sponsored by IEEE
Beijing
Section,
with
ASEMD, covers electric, magnetic, and electronic
organizers of Shanghai University, Shanghai Key
devices, either superconducting or not. This part also
Laboratory for High Temperature Superconductors,
includes
Tianjin
measurement, and automation.
and
and
Electromagnetic devices, the other principle part of
principal
University,
co-sponsors
ASEMD scope.
Shanghai
Creative
Superconductor Technologies Co. Ltd.
work
in
electromagnetic
analysis,
ASEMD2015 continues the focus and provides a
The 1st ASEMD conference was held in Chengdu,
forum for both academic and industrial researchers in
China, on September 25-27, 2009, the 2nd was in
the relevant fields to discuss and share ideas, present
Sydney, on December 14-16, 2011, and the 3rd was in
results, reflect on past experiences and discuss future
Beijing, China, on October 25-27, 2013. The IEEE ASEMD
developments.
devotes itself to providing the researchers in the field of
Contributed papers to this conference will be
applied superconductivity and electromagnetic devices
published in its proceedings in the IEEE Xplore digital
a
library, selected contributions will be published in a
platform
for
technical
discussion,
exchanging
information, and progress updates.
special
Applied superconductivity is generally categorized
into material, electrical and electronic sections. Material
synthesis and characterization, power applications,
4
issue
of
IEEE
Transaction
on
Applied
Superconductivity through the normal peer review
process.
ASEMD2015
Shanghai, China
Nov.20-23, 2015
Conference Organization
Sponsors and Organizers
Sponsor - IEEE Beijing Section
Co-sponsors - Tianjin University, Shanghai Key
Laboratory for High Temperature Superconductors,
and Shanghai University
Organizers - Shanghai University, Shanghai Creative
Superconductor Technologies Co. Ltd., and Tianjin
University
Conference Chairs
Chuanbing Cai, Shanghai University
Jianxun Jin, Tianjin University
International Steering Committee
Yanfang Bi, Institute of Plasma Physics, CAS, China
Tim Coombs, Cambridge University, UK
Shixue Dou, University of Wollongong, Australia
Yusheng He, Institute of Physics, CAS, China
Faz Rahman, University of New South Wales,
Australia
Justin Schwartz, North Carolina State University, USA
Xuechu Shen, Shanghai Institute of Technical Physics,
CAS and Shanghai University, China
Qiuliang Wang, Institute of Electrical Engineering,
CAS, China
Dong Wei, Shanghai Electric Cable Research Institute
Wancheng Sheng, Shanghai University, China
Judy Wu, Kansas University, USA
Jianguo Zhu, University of Technology, Sydney,
Australia
Program Committee
Chair: Ying Xin, Tianjin University, China
Members:
Boxue Du, Tianjin University, China
Jia Du, Commonwealth Scientific and Industrial
Research Organization, Australia
Rene Fuger, Guina Energy Group, Australia
Colin Grantham, University of New South Wales,
Australia
Youguang Guo, University of Technology, Sydney,
Australia
Bernhard Holzapfel, Karlsruhe Institute of Technology,
Germany
5
Hongjie Jia, Tianjin University, China
Bin Li, Tianjin University, China
Quan Li, University of Edinburgh, UK
Xavier Obradors, Institute of Materials Science of
Barcelona, Spain
Ronghai Qu, Huazhong University of Science and
Technology, China
Timing Qu, Tsinghua University, China
Sergey Samoilenkov, Super Ox, Russia
Yuejin Tang, Huazhong University of Science and
Technology, China
Guoxiu Wang, University of Technology, Sydney,
Australia
Shuhong Wang, Xi’an Jiaotong University, China
Xiaolin Wang, University of Wollongong, Australia
Yinshun Wang, North China Electric Power University,
China
Zanming Wang, Alltech Medical Systems, China
Dong Wei, Shanghai Electric Cable Research Institute,
China
Xiaoming Xie, Shanghai Institute of Microsystem and
Information Technology, China
Yiyuan Xie, Suzhou Advanced Materials Research
Institute, China
Jincang Zhang, Shanghai University, China
Yifei Zhang, Superpower, USA
Local Organizing Committee
Huashi Xue, Guohui Hu, Changqing Gong, Jidong Sun,
Hui Yuan, Yibing Zhang, Xinluo Zhao, Quanzhong Chu,
Qi Lu, Xiaoyan Jin, Meng(Marvin) Yu, Yanqun Guo,
Zhiyong Liu, Yuming Lu, Chuanyi Bai, Feng Fan,
Hongbin Jian and Hong Zhang (Shanghai Creative
Superconductor Technologies; The College of Science
of Shanghai University)
Publication Board
Chairs: Jianxun Jin, Mengqi Zhou
Editors:
Chuanbing Cai, Tim Coombs, Boxue Du, Jia Du, Colin
Grantham, Youguang Guo, Quan Li, Ronghai Qu,
Yiyuan Xie, Ying Xin
(All names listed in each committee alphabetically)
ASEMD2015
Shanghai, China
Nov.20-23, 2015
Conference Venue and Transportation
02
Venue Information
Nanjiao Hotel (Five-star), No.8 Wang-yuan Road, Fengxian District, Shanghai, China 201400.
Website: http://www.nanjiaohotels.com/index-en.html
Contact person: Ms. Ting Wang, Email: wangting033@qq.com; Telephone: (+86)13761047334
Hotels
1.
Nanjiao Hotel（Conference Venue）南郊宾馆(主会场)
Superior Twin Room(with breakfast): RMB480
Superior Double Room(with breakfast) :RMB480
Add: No.8 Wangyuan Rd, Nanqiao County,
Fengxian District, Shanghai
（上海市奉贤区南桥新城望园路 8 号）
Tel: 021-67105886
http://www.gzdhwf.cn/home/20399/
6
ASEMD2015
Shanghai, China
Nov.20-23, 2015
Map of Main Venue
First Floor
Hall 6
Hall 5A/B
Grand Auditorium
Front Hall
一层平面图
The hotel main entrance
Second Floor
floor
Registration
Sunshine Buffet
7
ASEMD2015
Shanghai, China
Nov.20-23, 2015
Map of New Campus, Shanghai University
Chrysanthemum Show on New Campus, Shanghai University
8
3.Shanghai Meilia Jinn Business
Hotel 上海梅丽亚晶酒店
2.Shanghai Quan Ji Hotel
上海全季酒店南桥店
Standard Single (with breakfast for two) RMB264
Standard Single (with breakfast for two) RMB168
Double Twin Room (with breakfast for two) RMB264
Double Twin Room (with breakfast for two) RMB168
Add: No.7318 East Nan Feng Rd. Fengxian District
Add: No.8505 East Nan Feng Rd. Fengxian District
（上海市奉贤区南桥镇南奉公路 7318 号）
（上海市奉贤区南桥镇南奉公路 8505 号）
Tel:：021-37195999 Total Rooms：100
Tel：021-51391888
4. Jurun Hotel
5. Shanghai Crystal Island Club
聚润宾馆
上海丽州俱乐部
Total Rooms：200
Superior Standard Room (with breakfast for two)
Standard Single (with breakfast for two) RMB268
RMB260
Double Room (with breakfast for two) RMB268
Superior Double Room (with breakfast for two)
Add: No.383-399 East Huancheng Rd. Fengxian District
RMB260
（上海市奉贤环城东路 383-399 号）
Add: Lane299 Defeng Rd, Nanqiao County, Fengxian
Tel: 021-67107111
District（上海市奉贤南桥新城德丰路 299 弄）
http://www.lizhouclub.cn/
Tel: 021-37196799
http://www.jdydb.com/hotel/home-32482
Note:

ASEMD shuttle bus to be
available each hour on the
hour to Nanjiao Hotel
departing from Waihuanlu
Station of Metro Line1
from 10:00 am till 10:00
pm on Nov. 20.

All hotels listed above are
close to conference venue,
Nanjiao Hotel, within 5
kilometers.

Contact
ASEMD2015
people ： Ting WANG ：
13761047334
Yun SONG：15001846929
9
ASEMD2015
Shanghai, China
Nov.20-23, 2015
ASEMD2015 会期交通整体示意图
Illustration for Overall Travel during ASEMD2015 Conference
10
ASEMD2015
Shanghai, China
Nov.20-23, 2015
Transportation
1.
Depart from Hongqiao Railway Station to
Nanjiao Hotel
（虹桥火车站—南郊宾馆）

Metro Line 10 (From Hongqiao Railway
Station to South Shanxi Rd.)

Transfer to Metro Line 1 (From South Shanxi
Rd. to Waihuanlu)

Take ASEMD shuttle bus (From 10:00am to
10:00pm only, the 20th November) or take
taxi to Nanjiao Hotel (around half an hour
RMB50).
2.
Depart from Shanghai South Railway Station
to Nanjiao Hotel

Metro Line 1 (From Shanghai South Railway
Station to Waihuanlu)

Take ASEMD shuttle bus (From 10:00am to
10:00pm only, the 20th November) or take
taxi to Nanjiao Hotel (around half an hour
RMB50).
11
ASEMD2015
Shanghai, China
Nov.20-23, 2015
3. Depart from Hongqiao International Airport
to Nanjiao Hotel

Metro Line 10 (From Hongqiao Airport
Terminal 1 or Hongqiao Airport Terminal 2 to
South Shanxi Rd.)

Transfer to Metro Line 1 (From South Shanxi
Rd. to Waihuanlu)

Take ASEMD shuttle bus (From 10:00am to
10:00pm only, the 20th November) or take
taxi to Nanjiao Hotel (around half an hour
RMB50).
4. Depart from Shanghai Railway Station to
Nanjiao Hotel

Metro Line 1 (From Shanghai Railway Station
to Waihuanlu)

Take ASEMD shuttle bus (From 10:00am to
10:00pm only, the 20th November) or take
taxi to Nanjiao Hotel (around half an hour
RMB50).
12
ASEMD2015
Shanghai, China
Nov.20-23, 2015
5. Depart from Pudong International
Airport to Nanjiao Hotel

Metro Line 2 (From Pudong
International Airport to People’s
Square)

Transfer to Metro Line 1 (From People’s
Square to Waihuanlu)

Take ASEMD shuttle bus (From 10:00am
to 10:00pm only, the 20th November)
or take taxi to Nanjiao Hotel (around
half an hour RMB50).
Note：Direct Taxi suggested strongly
13
ASEMD2015
Shanghai, China
Nov.20-23, 2015
Registration and Key Reminders
03
Accompanying person registration fees include:
Admission to receptions and the banquet conference
Registration and Payment
I.
organized tours.
Registration Time:
Registration on site from 13:00 to 22:00 pm on
November 20, and each Morning, November 21-22,
IV. Bank Accounts
Registration fees can be paid by direct bank transfer
2015.
into the following ASEMD bank accounts:
II. Registration Fee:
The registration fee rates are as followings: Early
bird rate before Oct. 15, 2015; Full conference attendee:
单位名称： 上海大学
US$625; Student (Post-doctoral position excluded):
银行账号： 033270-00801210489
US$425; Standard rate (after Oct. 15, 2015);Full
conference attendee: US$695; Student (Post-doctoral
position excluded): US$495; Accompanying person
开户银行： 中国农业银行上海市宝山区大场支行
银行行号： 103290005138
registration rate: US$200; Additional page or paper
charges: Charge for an additional page (the third page):
US$100; Charge for an additional paper (up to 3 pages):
US$300; Exhibitors rate:
US$5000/booth, including
two attendees conference fees.
单位名称： 天津大学
银行帐号： 1036 0120 1090 008441
开户行名称：天津银行兴科支行
III. Payment Way
Please be advised that an early bank transfer is
联行号：
313110040364
required strongly, while on-site payment will be
Bank Name: Australia and New Zealand Banking Group
acceptable for few case, but cash only.
Note:
Registration
covers： Access to all
Limited (ANZ)
Account Name: Science Platform Corporation
technical (oral and poster) sessions，Access to the
BSB No: 012-003
exhibition; Admission to the banquet and coffee breaks;
Account No: 493962696
Conference organized tours，Up to two manuscript
SWIFT Code: ANZBAU3M
(Bank address / Branch name: 115 Pitt St, Sydney, NSW
submissions to IEEE Xplore and one to IEEE Transaction
on Applied Superconductivity, USB chips with the
conference proceedings.
14
2000, Australia )
Information for Presenters
I.
Conference dinner
1)
The conference has 5 meal vouchers.
2)
One meal voucher per person per meal. Because the restaurant reception capacity is close to saturation, in order
to maintain good order, please sequentially enter the restaurant, A staff will charge the meal voucher at the
entrance.
3)
The entourage, family members et al., of the participants who do not pay the registration fee but want to eat at
the restaurant, please purchase the meal vouchers from the staff at the report site. The meal vouchers are not
returned after sold.
II. Arranged venues
The conference has one Main Conference Hall (multi-function hall) and four Sub Conference Halls (namely Grand
Auditorium、Hall 1、Hall 2、Hall 4、Hall 5A/5B、Hall 6), which are all located on the 1st floor of Nanjiao Hotel.
III. Plenary and oral talk
Please representatives of plenary talk copy PPT to the specified computer (at least one session in advance), and
confirmed it can work instantly.
IV. Poster exhibition
1)
The size of poster is 80 cm X 180 cm, please make it according to the size.
2)
Please indicate authors’ name, poster number (seeking in program), and telephone on the top left corner of
poster.
Information for Best Student Paper Award
The conference committee decides to award FIVE Prizes to postgraduate students for outstanding work
presented in person by poster or oral during the ASEMD2015 conference. Each prize-winner receives a printed
certificate and cash of RMB 1000 yuan.
The main criteria for the award of the five prizes are the work originality and the general quality of the poster
or oral presentation, judged by three reviewers (Prof. Yanfan Bi, Prof. Shuhong Wang, and Prof. Yinshun Wang).
15
ASEMD2015
Shanghai, China
Nov.20-23, 2015
Guidelines for Oral Presentation
04
1.
The guidelines are applicable for all plenary, invited and oral presentations.
2.
Presentation durations
•
Plenary: 30 minutes (25 minutes with 5 minutes for questions).
•
Invited: 20 minutes (18 minutes with 2 minutes for questions).
•
Contributed: 15 minutes (13 minutes with 2 minutes for questions).
The time limitations must be strictly observed.
3.
Presenters are asked to arrive a few minutes before the session and introduce themselves to the session chair
before the start of the session.
4.
Presentations will exclusively use the computers provided by ASEMD2015. The presenters are not allowed to use
their personal computer. Using removable media (USB drives) is prohibited on the computers in oral session
rooms.
5.
A Speaker Preparation Room is available at the conference venue (located at Hall 1). Presenters should submit
an electronic version of their talk at least one day prior to their presentation to the Speaker Preparation Room
(for example, for those on November 22, should submit it after registration). Files should be reviewed at the
same time by the presenter. Changes to submitted files will not be allowed.
6.
Presentations must be submitted in Microsoft Power Point format. Acceptable media include CD and USB flash
drive. Macintosh computers will not be available in any of the session rooms. Authors using a Macintosh must
ensure their presentations operate correctly using Microsoft Office or Adobe Acrobat in the Windows
environment.
7.
Files transferred to the session computers cannot be copied by anyone and will be deleted after the session.
Anyone wishing to receive a copy of the slides should contact the presenter, not ASEMD2015.
16
ASEMD2015
Shanghai, China
Nov.20-23, 2015
Instructions for Session Chairs
05
Instructions for chairs of plenary talks
As plenary session chair, you are expected to reach the Grand Auditorium at least 5 minutes before the start of your
plenary session. First verify the presence of the scheduled speakers of the session. For each presentation, you are
expected to introduce the speakers by name, organization, brief vita and the title of talk. Each plenary talk is
permitted 30 minutes, 1 for introduction, 25-27 for presentation, 2-4 for questions. You can allow people from the
audience to ask one or more questions, depending on the time that is available. It is required that the total time limit
of 30 minutes for each plenary presentation should be strictly observed! After finishing your session, you need to fill
out and sign the Session Report sheet. Assistant worker will collect the sheet in each meeting room after each
session.
Instructions for oral session chairs
As oral session chair, you are expected to reach meeting room at least 5 minutes before the start of your session. First
verify the presence of the scheduled speakers of the session. You are expected to introduce the speakers by name,
organization and title of their talk. Each invited oral is permitted 20 minutes, 15-17 for presentation, 3-5 for questions.
Each contributed oral is permitted 15 minutes, 12-13 for presentation, 2-3 for questions. You can allow people from
the audience to ask one or more questions, depending on the time that is available. It is required that the total time
limit for each presentation should be strictly observed! After finishing your session, you need to fill out and sign the
Session Report sheet. Assistant worker will collect the sheet in each meeting room after each session.
Instructions for poster session chairs
As poster session chair, you are expected to present all the time during the 2 poster sessions of the conference. You
are expected to cruise the poster areas and check out the authors’ attendance. After finishing the poster sessions,
you need to fill out and sign the Session Report sheet. Assistant worker will collect the sheet after the poster
sessions.
17
ASEMD2015
Shanghai, China
Nov.20-23, 2015
Conference Program
06
Overview of All Programs
Date
Nov.20
Friday
Morning
Noon
Afternoon
Registration desk hours: 13:00-22:00 pm
ASEMD bus from Metro Line 1 to Nanjiao from 10:00am to
10:00pm. Committee Members Meeting
Evening
Buffet
18:30-20:00
Oral Session
Opening
13:30-15:25
Nov.21
09:00-09:30
Lunch
Oral Session
Banquet
Saturday
Plenary I
12:15-13:30
15:40-17:35
18:45-20:00
9:45-12:15
Poster Session
17:35-18:30
Oral Session
Nov. 22
Sunday
Plenary II
13:30-15:30
08:00-09:30
Lunch
Poster Session
Buffet
Oral Session
12:10-13:30
15:45-16:30
18:45-20:00
9:45-12:10
Plenary III + Awarding
16:30-18:30
Nov. 23
Monday
Technical Tour to:
SCSC and SECRI*
08:00-11:30
Lunch and
Check in SHU
Lehu Hotel
11:30-13:00
*Note:
SCSC--Shanghai Creative Superconductor Co. Ltd,
SECRI--Shanghai Electric Cable Research Institute,
SHU--Shanghai University
18
HTS Application
Workshop
14:00-16:30
Technical Tour to:
HTS Lab
Fast Food &
Chrysanthemum
show on Campus
16:30-18:00
November 21, 2015（Saturday, 9:00-18:30）
Time
Activities
Places
09:00-09:20
Opening & Official Speeches
Grand Auditorium
09:20-09:30
Group Photo
Hotel Entrance
09:45-12:15
Plenary Session I
Grand Auditorium
12:15-13:30
Lunch
Dining Hall (2nd Floor)
Oral Session
Hall 2、Hall 4、Hall 6, and Grand
A1、D1、F1、H1
Auditorium
13:30-15:25
15:25-15:40
Tea Break
Oral Session
Hall 2、Hall 4、Hall 6, and Grand
A2、D2、F2、H2
Auditorium
17:35-18:30
Poster Session
Hall 5A-5B + Front Hall
18:45-20:00
Banquet
Dining Hall (1st Floor)
15:40-17:35
Session A: Materials
Session C: Electrical Power Systems
Session E: Magnets
Session G: Cryogenics & Thermal/Electrical Insulation
Session B: Superconducting Electric Power Devices
Session D: Electrical Machines
Session F: Electronics
Session H: Modeling, Analysis and Design
November 22, 2015（Sunday 8:00-18:30）
Time
Activities
Places
08:00-09:30
Plenary Session II
Grand Auditorium
09:30-09:45
Tea Break
09:45-12:10
12:10-13:30
13:30-15:30
Oral Session
Hall 2、Hall 4、Hall 6, and Grand
B1、C、E1、G
Auditorium
Lunch
Dining Hall (2nd Floor)
Oral Session
Hall 2、Hall 4、Hall 6, and Grand
B2、D3、E2、H3
Auditorium
15:30-15:45
Tea Break
15:45-16:30
Poster Session
16:30-18:30
18:45-20:00
Hall 5A-5B + Front Hall
Plenary Session III
Awards for Best Student Papers
Dinner
Grand Auditorium
Dining Hall (2nd Floor)
19
`
November 23, 2015
（Monday 8:00-18:00）
Time
Activities
Group I
Check out from Nanjiao Hotel, and
8:00-09:00
Technical Tour to:
2066 Wangyuan Road, Fengxian
Group II
Shanghai Creative Superconductor.
District, Shanghai
8:30-9:30
Co. Ltd.
Group I:
9:00-10:30
Group II:
9:30-11:00
Group I:
10:30-11:30
ASEMD bus to:
Shanghai Electric Cable Research
Institute(SECRI)
Technical Tour@ SECRI
Places
1000 Jungong Road, Yangpu
District, Shanghai
1000 Jungong Road, Yangpu
District, Shanghai
Group I:
Check in and Lunch @ Lehu Hotel,
New Campus, Shanghai
11:30-12:30
Shanghai University
University (SHU)
Group II:
11:00-12:00
Technical Tour@ SECRI
Group II:
Lunch@ SECRI;
12:00-13:00
Check in SHU Lehu Hotel
14:00-16:30
1000 Jungong Road, Yangpu
District, Shanghai
New Campus, SHU
HTS Application Workshop
Lecture Hall, 2nd Floor, SHU Lehu
Plenary Talks
Hotel
Technical Tour to Shanghai Key
16:30-17:00
Laboratory for High-Tc
New Campus, SHU
Superconductors
17:00-18:00
Fast Dinner and Free Tour
20
SHU Lehu Hotel
Plenary and Selected Invited Speeches
-Brief Biographies
Title of Presentation
Advances in Bi2Sr2CaCu2Ox Superconducting Wires and Related Technologies for High Field
Superconducting Magnets
Prof. Justin Schwartz
Professor
North Carolina State University
USA
Justin Schwartz received a B.S. from the University of Illinois at Urbana-Champaign in 1985 and a Ph.D.
from the Massachusetts Institute of Technology, Cambridge, in 1990. After serving as one of the first
Science and Technology Agency of Japan Fellows at the National Research Institute for Metals, Japan, he
joined the University of Illinois at Urbana-Champaign as an Assistant Professor. In 1993, he joined the
newly-formed National High Magnetic Field Laboratory and the Department of Mechanical Engineering at
Florida State University, where he served as the Leader of the HTS Magnets and Materials Group. In 2003,
his research group, in collaboration with Oxford Instruments, established the world record for magnetic
field generation by a superconducting material. In 2009, Professor Schwartz joined North Carolina State
University as the Head of the Department of Materials Science and Engineering and Kobe Steel
Distinguished Professor. His research interests include superconducting materials, multiferroic materials,
and other functional oxides, with emphases on performance-limiting mechanisms, manufacturing-relevant
processing techniques and failure mechanisms, which he studies through experimental and
microstructurally-driven computational research. Prof. Schwartz was the Editor-in-Chief of the IEEE
Transactions on Applied Superconductivity from 2005-2012 and is a Fellow of the IEEE.
Title of Presentation
Progress in Nanostructured Coated Conductor Research and Development
Prof. Xavier Obradors
Director, ICMAB – CSIC
Editor, Physica C
Spain
21
Xavier Obradors received a Degree of Physics at the University of Barcelona (Spain) in 1978, a PhD in
Materials Science at the University of Grenoble (France) in 1983 and a PhD in Physics at the University of
Barcelona in 1982. After serving as Associate Professor at University of Barcelona during six years he joined
the Institute of Materials Science of Barcelona (ICMAB), National High Research Council (CSIC) in 1988 and
in 1992 he became Research Professor at ICMAB. Prof. Xavier Obradors is the director of ICMAB – CSIC
since 2008. His scientific interests include materials preparation with controlled microstructures and the
comprehension of the physical mechanisms underlaying the superconducting, magnetic and electronic
properties of nanostructured materials. He has received numerous awards for his contributions to
Materials Science, Superconductivity and Clean Energy developments (Fellow of Institute of Physics of UK;
Doctor Honoris Causa University of Pitesti, Romania; ENDESA Novare Award; National Materials Science
Award, Spain; Member of Academy of Sciences and Arts of Bareclona; Narcis Monturiol medal of the
Catalan Government; Academic Palm of French Government). He served in the Editorial Board of
Superconductor Science and Technology (1996-2001) and at present he is editor of Physica C since 2008.
He also has served as President of European Society of Applied Superconductivity (2006-2011). He has
published more than 490 articles having received more than 8200 citations (h=42);he has filed more than
12 patents and he was one of the creators of the spin-off company OXOLUTIA. At present he coordinates
EUROTAPES, a large academic and industrial consortium devoted to the development of coated
conductors in Europe.
Title of Presentation
Superconducting Nanowire Single Photon Detection (SNSPD): Principle, Progress and
Applications
Dr. Lixing You
Senior researcher, Shanghai Institute of Microsystem and Information
Technology (SIMIT)
Senior visiting fellow, University of California
China
Lixing YOU received the B.S., M.S. and Ph.D. degrees in radio physics from Nanjing University, China, in
1997, 2001 and 2003 respectively. From Apr. 2000 to Mar. 2001, he was a research student in RIEC,
Tohoku University, Japan. From Nov. 2003 to Oct. 2005, he was a Post-Doctoral Researcher with MC2,
Chalmers University of Technology, Sweden. From Nov. 2005 to Jun. 2006, he was a Post-Doctoral
Researcher in University of Twente, the Netherlands. From Sept. 2006 to Aug. 2007, he was a Guest
Researcher in NIST@Boulder, USA. Since Sept. 2007, he has been a senior researcher in Shanghai Institute
of Microsystem and Information Technology (SIMIT), Chinese Academy of Sciences, Shanghai, China.
Currently (Sept. 2015 – Feb. 2016) he is a senior visiting fellow in University of California, Berkeley. His
research interests are superconductive electronics including micro/nano superconducting devices and high
frequency applications. His current research is related to superconducting nanowire single photon
detection (SNSPD) and its applications. In SIMIT, he is the group leader in charge of the research on SNSPD.
He has published over 80 papers in peer-reviewed academic journals and owns 10 patents. He is a member
of WG14 in IEC-TC90, advisory board member for academic journal “Superconductor Science and
Technology” and international committee member of International Workshop of Superconducting Sensors
and Detectors.
22
Title of Presentation
PM and Superconducting Technology Applications at GE
Dr. Manoj Shah
GE’s Global Research Center
USA
Dr. Manoj Shah received his B. Tech. (Honors) from Indian Institute of technology, Kharagpur, India, and
his MSEE and Ph.D. from Virginia Tech. He worked for Westinghouse Electric (Now Siemens) and later
joined GE after a short stint at Rensselaer Polytechnic Institute (RPI) in 1981. His career has spanned
Aviation and Naval Electrical Systems, Electromagnetic Launchers, Large Turbine-Generators, and so on.
His current tenure at GE’s Global Research Center in upstate New York has been centered on developing
advanced electrical machines and devices employing novel topologies in concert with the use of latest
materials (magnetic, non-magnetic, metals, non-metals, composites, HTS, etc.) and cooling technologies
for various GE businesses ranging from Aviation to Power Generation to Geothermal to Oil & Gas to
Transportation. He has over 60 US and many foreign patents along with over 45 publications, with a few of
them receiving Prize paper awards. He was made an IEEE Fellow in 2003 and received the 2012 IEEE Nikola
Tesla award for “Advancements in Electromagnetic Design and Analysis of Electrical Machines.” In early
2013, he received the 2012 Coolidge Fellowship Award, the highest research award in GE. Recently, he
received the 2015 IEEE – Industry Applications Society’s Industrial Power Conversion Systems
Department’s Gerald Kliman Innovator Award that recognizes meritorious contributions to the
advancement of power conversion technologies through innovations and their application to Industry.
Title of Presentation
Recent Progress and Trends in Coted Conductor Development in U.S.
Dr. Vyacheslav Solovyov
Brookhaven Technology Group Inc.
Brookhaven National Laboratory
USA
Dr. Vyacheslav Solovyov received his M.S. from Moscow Institute for Physics and Technology in 1989 and
Ph.D. from Kiev Institute for Metal Physics in 1995. In 1997 he joined Brookhaven National Laboratory as a
Research Associate. His work at Brookhaven concentrated on scaling production of Coated Conductors
using the ex-situ process. In 2007 his group achieved the highest absolute current in thick YBCO layers. His
scientific interests include physics and materials science of flux pinning, applications of oxide coating. He is
a member of Editorial Board of Scientific Reports, Nature Publishing Group.
23
Title of Presentation
Superconducting Metal Enclosed Liquid Nitrogen Insulated Switchgear
Prof. Jianhua Wang
State Key Laboratory of Electrical Insulation and Power Equipment，Xi’an
Jiaotong University
China
Jianhua Wang received the M.S. and Ph.D. degrees in Electrical Engineering in 1981 and 1985, respectively,
from Xi'an Jiaotong University, China. Currently, he is a Professor with the State Key Laboratory of
Electrical Insulation and Power Equipment, Department of Electrical Engineering, XJTU.
His research interests include theory and application of intelligent electrical apparatus systems, high
voltage vacuum switchgear, as well as computer-aided design/computer-aided engineering in electrical
engineering.
He is the Chairman of the professional branch committee on intelligent electrical systems and its
applications of the China Electrotechnical Society (CES), and the honorary Chairman of CES. From 2003 he
was the Director of the State Key Laboratory of Electrical Insulation and Power Equipment.
He was the Chairman of the 19th and 23th International Symposium on Electrical Discharge and Insulation
in Vacuum in 2000 and 2008 respectively. He was also the Chairman of the 1st International Conference on
Electrical Power Equipment—Switching Technology, Xi’an, 2011.
He was awarded the Honorary Professor title from Polytechnic University of Torino, Italy, in 2009. He was awarded
the Honorary Doctor of Law title from University of Liverpool, UK, in 2009.
From 2003 to 2014 he was the Chairman of the University Council of Xi’an Jiaotong University.
Title of Presentation
SMES for Pulsed Applications
Prof. Pascal Tixador
Full professor, Grenoble-INP
France
Pascal Tixador received the Engineer degree in electrical Engineering and the PhD degree from the
National Polytechnic Institute of Grenoble in 1984 and 1987 respectively. He was engaged at CERN, and in
1989 he has been employed by the CNRS (French National Scientific Research Centre) at the LEG (now
G2Elab (Grenoble Electrical Engineering Laboratory)) and CRTBT (now Institut Néel), two Grenoble
laboratories. Since September 2007, he is full professor at Grenoble-INP. His current interests are
superconducting large-scale applications from design to model construction, but also simulation activities
24
most of the time in collaboration with industry and laboratories through the world. He has authorised
more than 120 research publications and has supervised 26 PhD students. He was ESAS (European Society
of Applied Superconductivity) secretary from 2005 to 2011 and is the Chairman for EUCAS (European
Conference on Applied Superconductivity) in Lyon in 2015.
Title of Presentation
Advance in HTS Power Applications with Recent Activities in Germany
Prof. Bernhard Holzapfel
Full professor, Karlsruhe Institute of Technology (KIT)
Germany
Prof. Bernhard Holzapfel received both his Diploma (1990) and Ph.D. (1995) in Physics from the University
of Erlangen-Nürnberg, Germany. From 1990 to 1993, he was a Research Associate at the Siemens AG,
Erlangen. In 1993 he moved as PostDoc to the Leibniz-Institute for Solid State and Materials Research
Dresden (IFW Dresden). From May 1999 to June 2000, he was a Guest scientist at the Oak Ridge National
Laboratory, USA. In 2000, he was promoted to lead the superconducting materials group of the Institute for
Metallic Materials at the IFW Dresden. In 2008, he was honored as the adjunction professor of Shanghai
University, and addressed lectures in Shanghai for two months. In 2013, he joined Karlsruhe Institute of
Technology (KIT) as a full professor for Superconducting Materials and co-director of the Institute for
Technical Physics. Due to a lot of excellent research works, he obtained high reputation in the field of
superconducting materials not only in the Europe, but also in the world. He is actually one of the leading
scientists of HTS materials research in Germany as well as in Europe. In 2006, he was awarded the prize of
Donors Association for German Science. This is one of the highest award for scientist in Germany. In the
past years, he has given more than 40 invitation talks or lectures around the world. He has also organized
several important workshops and big research programs in the European Union, such as the NESPA project,
which was one of the biggest superconductor research and training networks in Europe with 16 research
units involved from different EU countries.
Title of Presentation
Hydrostatic Pressure Induced Significant Enhancement of Critical Current Density by Orders of
Magnitude in Iron Pnictide Superconducting Tapes, Granular Bulks and Single Crystals
Professor Xiao-Lin Wang
Institute for Superconducting and Electronic Materials,
Faculty of Engineering, Australian Institute for Innovative Materials,
University of Wollongong
Australia
Professor Xiao-Lin Wang received his PhD in 2000 from the University of Wollongong, Australia. He is
currently the Associate Director of the Institute for Superconducting and Electronic Materials, Australian
Institute for Innovative Materials at the University of Wollongong. He is also the group leader of the
Spintronic and Electronic Materials team at the Institute. He currently holds an ARC Future Fellowship
(Step 3). Prof. Wang’s research interests include innovative design of new class of materials, solid state
physics and materials science, superconductors, spintronics, topological insulators/materials, ferroelectrics,
magnetism, multiferroics, superconductors, thermoelectricity, etc. He proposed a concept for a new class
of materials, spin gapless semiconductors, which has been widely verified both theoretically and
experimentally by many groups worldwide. He has published over 300 papers in many prestigious journals
including “Nature Materials”, “Physical Review Letters”, “Advanced Materials”, “Angewandte Chemie”,
“Nano Letters”, “Advanced Functional Materials”, etc. Prof. Wang has attracted more than 5000 citation
and has h-index of 34. He has supervised more than 20 PhD students to completion and currently
supervisor of 10 PhD students. Professor Wang is an elected Fellow of Australian Institute of Physics and
previously held an ARC QEII Fellowship.
Title of Presentation
Design and Development of Magnets for HL-2M Tokamak
Prof. Qiang Li
Southwestern Institute of Physics
China
Li Qiang graduated from Chongqing University in 1990 with a BA degree, and from Southwestern Institute
(SWIP) of Physics in 2006 with a Ph. D degree. He joined SWIP in 1990 and has been working there so far
for magnetic confined fusion plasma research. He became an electrical engineering in 1995, a senior
engineer in 1999 and a research professor in 2005. He worked at electromagnetic measurement from 1990
to 1997, experimental study of reversed-field pinch plasmas from 1994 to 1997, electrostatic probe
measurement for edge plasma of HL-1M tokamak from 1997 to 1999, z-pinch plasma from 1997 to 2000.
He then worked on HL-2A tokamak from 1999 for plasma control, plasma boundary identification, and
experimental data management. He is now working at HL-2M for component design and HL-2M
construction.
Title of Presentation
Progress in the Development of Superconducting Machines
Dr. Tim Coombs
Senior Lecturer, Cambridge University
Guest Professor, Tshinghua University
UK
26
25
Dr. Tim Coombs is a Senior Lecturer in the Electrical Engineering Department at Cambridge University and
A Guest Professor at Tshinghua University. Dr. Tim Coombs heads the EPEC Superconductivity group at
Cambridge University. He gained both his undergraduate and graduate degrees from Cambridge University.
His research interest is Applications of Superconductivity and he holds more than 20 years’ experience in
superconducting engineering, covering both experimental and theoretical aspects. Dr. Coombs leads one of
the strongest superconducting groups in the world with an extensive portfolio of experimental techniques,
mathematical analysis tools and machine designs. He has an internationally leading publication record
which extends to more than 100 papers released in high impact scientific journals. He has worked on novel
solutions to the Critical State, developing one of the first algorithms capable of calculating the critical state
in two dimensions. He also pioneered the (now standard) use of the H-formulation. His group constructed
the world's first all superconducting motor and he has achieved global recognition for his novel ideas on
the magnetisation of superconductors which will provide a field strength an order of magnitude stronger
than conventional magnetic materials, enabling smaller, lighter, more efficient motors and generators. Dr.
Coombs has authored more than ten patents and has a particular specialisation in Magnetism.
Title of Presentation
HTS for Renewable Energy
Dr. Quan Li
Centre for Superconductor and Energy Technology University of
Edinburgh
UK
Dr. Quan Li received both Bachelor (2003) and Master (2006) in Engineering from Tsinghua University China,
and PhD (2011) from the University of Cambridge UK. In 2011, he was awarded “Young Scientist Research
Fellowship” by the Japan Society for the Promotion of Science (JSPS) and was working on HTS power
applications at Kyoto University Japan from 2011 to 2013. Now he is an Assistant Professor (Lecturer) at the
University of Edinburgh, leading a group working on Superconductor and Energy Technology, including
power cables, power generators, medical accelerators and novel HTS renewable energy applications. He is
also a Guest Professor at Tianjin University, a Guest Lecturer at KTH Royal Institute of Technology, and a
Fellow of Higher Education Academy (FHEA). He was awarded “Lundgren Research Award” in UK 2009,
“Researcher of the Year” in Japan 2013, “Principal’s Excellence Award” in UK 2014. He acts as External PhD
Examiner at the University of Cambridge, Conference Chairman of International Conference on Energy
Challenges, Vice-President of Scotland Sustainable Energy Society, Programme Committee Member of
IEEE/IET international conferences. He has been invited to over 15 international conferences and has given
more than 20 invited talks and lectures in the past years.
27
Title of Presentation
Cryogenic Electrical Insulation - Common Techniques for Superconducting Power Application
Prof. Naoki HAYAKAWA
Department of Electrical Engineering and Computer Science,
Nagoya University
Japan
Naoki Hayakawa received the B.S., M.S. and Ph.D. degrees in electrical engineering from Nagoya University
in 1985, 1987 and 1991, respectively. Since 1990, he has been at Nagoya University and presently he is a
Professor of Nagoya University at the Department of Electrical Engineering and Computer Science. From
2001 to 2002, he was a guest scientist at the Forschungszentrum Karsruhe/Germany. His research interests
include high voltage engineering and electrical insulation techniques for electric power apparatus including
superconducting power apparatus. He has published over 170 papers in peer-reviewed academic journals.
Prof. Hayakawa is a member of IEEE, IEE of Japan and CIGRE, and the secretary of CIGRE WG D1.38
“Emerging Test Techniques Common to High Temperature Superconducting (HTS) Power Applications”.
Title of Presentation
The Production of High-quality 2G HTS Wire and its Integration into Devices from a Russian
Perspective
Dr. S. Samoilenkov
SuperOx, 20/2 Nauchnyi proezd
Russia
Dr. Sergey Samoilenkov was a student of Chemistry Department, Moscow State University during
1991-1996, and then a postgraduate student of Chemistry Department, Moscow State University, with the
Diploma in the field of LuBa2Cu3O7-x thin films at Moscow State University in 1996, and PhD Thesis of
“Thin epitaxial RBa2Cu3O7-x films: metalorganic chemical vapor deposition, structure and properties”,
Moscow State University in 1999, respectively. During 2000-2005, he was a research fellow at Institute of
Surface Technics (Institut fuer Oberflaechentechnik, IOT), Braunschweig Technical Univeristy, Germany.
From December 2005 to the present time, he has been a senior scientific researcher at the Institute of High
Temperature RAS, Moscow. During November 2006 – February 2013, he was the Chief Technical Officer of
SuperOx, and from February 2013 to the date, he has been the Chief Executive Officer of SuperOx. His
professional interests cover the Materials science, Electroenergetics, Thin films and coatings, High
temperature superconductors (HTS). Moreover, his received a number of awards, including the 1996 Young
Scientist Award of European Materials Research Society, Strasbourg, France, 2006 Laureate of scientific
work contest in energetics “New generation” (RAS and RAO EES), Moscow, and 2008 Laureate of the
contest “Energy of youth”, “Global Energy” foundation, Moscow.
28
Title of Presentation
Recent Development of Small-scale Stirling Cycle Based Cryocoolers
Prof. Wei Dai
Key laboratory of Cryogenics
Chinese Academy of Sciences
China
Dr. Wei Dai received a Bachelor degree from Shanghai Jiao Tong University in 1994 and a Ph.D. from
Shanghai Jiaotong University in 2000. After spending two years as Post-doc in Nihon University of Japan, he
joined Technical Institute of Physics and Chemistry of Chinese Academy of Sciences. His research interests
include cryocoolers, Stirling engines, thermoacoustics and flow visualization technologies. He has
published over 30 international journal papers on cryocoolers and thermoacoustics.
Title of Presentation
Superconducting Motor Developments at Guina Energy Technologies
Dr. Rene Fuger
Guina Energy Group
Australia
Dr. Rene Fuger completed the diploma program in Technical Physics, Vienna University of Technology,
Austria, in April 2005, with the thesis: ”Magnetic and superconducting phase transitions in HoNi2B2C
single crystals”, and then a doctoral program in Technical Science, Vienna University of Technology, Austria,
in October 2008, with the thesis: ”Analysis of high temperature superconductors for applications in fusion
magnets”. After that, he was employed as a Postdoctoral Researcher at Kyushu University from November
2008 to February 2011, conducting the experimental verification of high temperature superconductor wire
performance with different techniques and equipments. Then he joined the Guina Energy Group, Australia,
focusing on the reviewing, developing, testing and analyzing of new technologies for high performance
electric motors and generators, as well as working with multi-physics software to analyze electromagnetic
and thermal designs, and coordinating and supervision of projects from design to final manufacturing state
and experimental verification of proof-of-concept models.
45
29
27
ASEMD2015
Shanghai, China
Nov.20-23, 2015
ASEMD2015
Technical Program
30
Overview for All Technical Program
Session
P
A
Subjects
Plenary Talks
Materials
Classificati
on
B
C
D
Electrical Power
Systems
Electrical
Machines
17:35-18:30 PM, Nov. 21
15:45-16:30 PM, Nov. 22
09:45-12:10 AM, Nov. 22
13:30-15:30 PM, Nov. 22
17:35-18:30 PM, Nov. 21
15:45-16:30 PM, Nov. 22
13:30-15:25 PM, Nov. 21
15:40-17:35 PM, Nov. 21
Hall 4
Hall 5A-5B&
Front Hall
Hall 4
Hall 4
FP-Poster
17:35-18:30 PM, Nov. 21
15:45-16:30 PM, Nov. 22
Hall 5A-5B&
Front Hall
G-Oral
09:45-12:10 AM, Nov. 22
Hall 6
GP-Poster
17:35-18:30 PM, Nov. 21
15:45-16:30 PM, Nov. 22
Hall 5A-5B&
Front Hall
H1-Oral
H2-Oral
H3-Oral
13:30-15:25 PM, Nov. 21
15:40-17:35 PM, Nov. 21
13:30-15:30 PM, Nov. 22
Hall 6
Hall 6
Hall 6
HP-Poster
17:35-18:30 PM, Nov. 21
15:45-16:30 PM, Nov. 22
WS
14:00-16:00 PM, Nov. 23
Hall 5A-5B&
Front Hall
Lecture
Hall@SHU
Lehu Hotel
09:45-12:15 AM, Nov. 21
PL-II
08:00-09:30 AM, Nov. 22
PL-III
16:30-18:30 PM, Nov. 22
A1-Oral
A2-Oral
13:30-15:25 PM, Nov. 21
15:40-17:35 PM, Nov. 21
17:35-18:30 PM, Nov. 21
15:45-16:30 PM, Nov. 22
B1-Oral
09:45-12:10 AM, Nov. 22
B2-Oral
13:30-15:30 PM, Nov. 22
17:35-18:30 PM, Nov. 21
15:45-16:30 PM, Nov. 22
09:45-12:10 AM, Nov. 22
17:35-18:30 PM, Nov. 21
15:45-16:30 PM, Nov. 22
BP-Poster
C-Oral
CP-Poster
D1-Oral
13:30-15:25 PM, Nov. 21
D2-Oral
15:40-17:35 PM, Nov. 21
D3-Oral
13:30-15:30 PM, Nov. 22
DP-Poster
E1-Oral
E
Magnets
E2-Oral
EP-Poster
F
G
H
W
Electronics
Cryogenics and
Thermal/Electrica
l Insulation
Modeling,
Analysis and
Design
HTS Application
Workshop
Room
Grand
Auditorium
Grand
Auditorium
Grand
Auditorium
Hall 2
Hall 2
Hall 5A-5B&
Front Hall
Grand
Auditorium
Hall 2
Hall 5A-5B&
Front Hall
Hall 2
Hall 5A-5B&
Front Hall
Grand
Auditorium
Grand
Auditorium
Grand
Auditorium
Hall 5A-5B&
Front Hall
Hall 4
PL-I
AP-Poster
Superconducting
Electric Power
Devices
Time
F1-Oral
F2-Oral
31
ASEMD2015
Shanghai, China
Nov.20-23, 2015
Plenary Sessions
Plenary I
9:45 AM to 12:15 PM, Saturday, November 21, 2015, Grand Auditorium
Chairs: Jianguo Zhu and Pascal Tixador
9:45 AM 1PL-01
Advances in Bi2Sr2CaCu2Ox Superconducting Wires and Related Technologies for High Field
Superconducting Magnets
Justin Schwartz
North Carolina State University, USA
10:15 AM 1PL-02
Progress in Nanostructured Coated Conductor Research and Development
X. Obradors1,T. Puig1,C. Pop1, S. Ricart1, M. Coll1, J. Gázquez1, A. Palau1, C. F. Sánchez1, X. Granados1,
P. Cayado1, B. Villarejo1, L.Soler1, B. Mundet1, F. Vallés1, A. Stangl1, Z. Li1, V R. Vlad2 A. Calleja2, M.
Vilardell2, A.Garzon3, N. Chamorro2, J.Ros3, P.Roura4, J.Farjas4, E. Bartolomé5, A. Usoskin6
1
Institut de Ciència de Materials de Barcelona, ICMAB-CSIC
Campus de la UAB, 08193 Bellaterra, Catalonia, Spain
2
OXOLUTIA SL, Edifici Eureka, Parc de Recerca de la UAB, Campus de la UAB, 08193, Bellaterra,
Catalonia, Spain
3
Departament de Química, Universitat Autonoma de Barcelona, Campus UAB, Cerdanyola,
Catalonia, Spain
4
Departament de Fisica, Universitat de Girona, Girona, Catalonia, Spain
5
Escola Univ. Salesiana de Sarrià (EUSS), 08017 Barcelona, Catalonia, Spain
6
Bruker HTS GmbH, Siemensstrasse, 88, 63755, Alzenau, Germany, Germany
10:45 AM 1PL-03
Superconducting Nanowire Single Photon Detection (SNSPD): Principle, Progress and
Applications
Lixing You
1
Division of Superconductivity, Shanghai Institute of Microsystem and Information Technology,
Chinese Academy of Sciences (SIMIT, CAS)
2
Department of Physics, University of California, Berkeley
11:15 AM 1PL-04
PM and Superconducting Technology Applications at GE
Manoj Shah
GE’s Global Research Center, USA
11:45 AM 1PL-05
Superconducting Metal Enclosed Liquid Nitrogen Insulated Switchgear
Jianhua Wang
State Key Laboratory of Electrical Insulation and Power Equipment, Xi’an Jiaotong University
Plenary II
8:00 AM to 9:30 AM, Sunday, November 22, 2015, Grand Auditorium
32
Chairs: Xavier Obradors and Justin Schwartz
8:00 AM 2PL-01
Advance in HTS Power Applications with Recent Activities in Germany
Bernhard Holzapfel
Karlsruhe Institute of Technology (KIT), Germany
8:30 AM 2PL-02
Design and Development of Magnets for HL-2M Tokamak
Yuntao Song
Southwestern Institute of Physics, Chengdu
9:00 AM 2PL-03
Progress in the Development of Superconducting Machines
T. A. Coombs1,2, L. Fu1, J. Geng1, M. Bagdhadi1, K. Matsuda2
1
Cambridge University
2
Magnifye Ltd, 66 Maids Causeway, Cambridge, UK
Plenary III
16:30 PM to 18:00 PM, Sunday, November 22, 2015, Grand Auditorium
Chair: Ying Xin and Tim Coombs
16:30 PM 3PL-01
SMES for Pulsed Applications
P. Tixador, A. Badel, J. Cicéron
Grenoble-INP, France
17:00 PM 3PL-02
HTS for Renewable Energy
Quan Li
Centre for Superconductor and Energy Technology, University of Edinburgh
17:30 PM 3PL-03
Recent Progress and Trends in Coted Conductor Development in U.S.
Vyacheslav Solovyov
1
Brookhaven Technology Group Inc., Stony Brook, NY
2
Brookhaven National Laboratory, Upton, NY
Oral Sessions
Session A1 Materials I
13:30 PM to 15:25 PM, Saturday, November 21, 2015, Lecture Hall 2
Chairs: Xiaolin Wang and Bernhard Holzapfel
13:30 PM A1-1 (Invited)
The Production of High-quality 2G HTS Wire and its Integration into Devices from a Russian
perspective
1
S. Samoilenkov, 1A. Molodyk, 2S. Lee, 2V. Petrykin, 1A. Mankevich, 1V. Kalitka, 1A. Blednov, 1M.
Moysykh, 1A. Markelov, 1I. Martynova, 1A. Adamenkov, 1V. Chepikov, 1V. Amelichev, 1A.Kamenev,
1
A. Makarevich, 1D. Gorbunova, 1A. Kaul
1
SuperOx, 20/2 Nauchnyiproezd, Moscow, Russia
2
SuperOx Japan LLC, SIC-3, 1880-2 Kamimizo, Sagamihara, Kanagawa, Japan
33
13:50 PM A1-2 (Invited)
Twiting Characterization of 2G HTS Tapes
Jiawei Li, Yinshun Wang
North China Electric Power University
14:10 PM A1-3
Surface Plasmon Polariton Propagation Modeling for Graphene Parallel Pair Sheets Using FDTD
1
M. MasudRana, 1M. Biplob Hossain, 1M. Rabiul Islam, 2Youguang Guo
1
Department of Electrical and Electronic Engineering, Rajshahi University of Engineering and
Technology, Bangladesh
2
Faculty of Engineering and Information Technology, University of Technology Sydney (UTS),
Sydney, Australia
14:25 PM A1-4
The Influence of the YBCO Tape Arrangement and Gap between the Two Tapes on AC Losses
1
Z.S.Wu, 1Y.R.Xue, 1J.Fang, 1Y.J.Huo, 1D.X.Chen, 2L.Yin
1
School of Electrical Engineering, Beijing Jiaotong University
2
Beijing Electric Power Economic Research Institute
14:40 PM A1-5
Experimental Research and Analysis of AC Critical Current in YBCO Tapes
Liu Erwei, Jin Fang, Chen Xiaoyu
School of Electrical Engineering, Beijing Jiaotong University
14:55 PM A1-6
Rebalance of Superconducting Tapes in Parallel Connection
Kun Yang, Bin Xiang, Yaxiong Tan, Zhiyuan Liu, YingsanGeng, Jianhua Wang，Satoru Yanabu
State Key Laboratory of Electrical Insulation and Power Equipment, Xi’an Jiaotong University
15:10 PM A1-7
Effects of Atmospheric Pressure on Tracking Failure of Epoxy/SiO 2 Nanocomposite
1
J. W. Zhang, 1Q. Q. li, 1Ang Ren, 2M. L Yin, 2Feng He, 2Bin Li
1
Shandong Provincial Key Laboratory of UHV Transmission Technology and Equipment, School of
Electrical Engineering, Shandong University
2
Jinan Power-supply Company
Session D1 Electrical Machines I
13:30 PM to 15:25 PM, Saturday, November 21, 2015, Grand Auditorium
Chairs: Fengge Zhang and Ronghai Qu
13:30 PM D1-1 (Invited)
A Novel Triple-Rotor Axial-Flux Vernier Permanent Magnet Machine
Rui Zhang, Jian Li, Dawei Li
State Key Laboratory of Advanced Electromagnetic Engineering and Technology, School of
Electrical & Electronic Engineering, Huazhong University of Science and Technology, Wuhan
13:50 PM D1-2 (Invited)
Magnetic Field Modulation Analysis and Experimental Research of Brushless Doubly
FedGenerator with Hybrid Rotor
Fengge Zhang, Siyang Yu, Xiuping Wang
School of Electrical Engineering, Shenyang University of Technology
14:10 PM D1-3
Influence of Different Stator Cores on Electromagnetic Performance of Axial Field Flux-Switching
Permanent Magnet Machines
34
1
Wei Zhang, 2Wei Zhang, 2Mingyao Lin, 2Da Xu, 2Yong Kong
1
School of Electrical Engineering, Nantong University
2
School of Electrical Engineering, Southeast University
14:25 PM D1-4
Design and Optimization of High Speed Permanent Magnet Synchronous Motor for Pulsed Power
system
Yuan Wan, Shumei Cui, Shaopeng Wu
School of Electrical Engineering and Automation, Harbin Institute of Technology
14:40 PM D1-5
An Optimal Flux-Switching Permanent Magnet Machine for Hybrid Electric Vehicles
1
Gang Lei, 1Youguang Guo, 1Jianguo Zhu, 2Wei Xu
1
School of Electrical, Mechanical and Mechatronic Systems, University of Technology, Sydney,
Australia
2
School of Electrical and Electronic Engineering, Huazhong University of Science and Technology
14:55 PM D1-6
Design and Analysis of a Permanent Magnet Slotted Limited-Angle Torque Motor with Special
Tooth-Tip Structure for Torque Performance Improvement
Jibin Zou, Guodong Yu, Yongxiang Xu, Junlong Li, Qian Wang
Department of Electrical Engineering, Harbin Institute of Technology
15:10 PM D1-7
Design and Analysis of a Hybrid Axial Field Flux-Switching Permanent Magnet Machine
Da Xu, Mingyao Lin, Xinghe Fu, Li Hao, Wei Zhang, Jilong Zhao
School of Electrical Engineering, Southeast University
Session F1 Electronics
13:30 PM to 15:25 PM, Saturday, November 21, 2015, Lecture Hall 4
Chairs: Shiping Zhao and Biaobing Jin
13:30 PM F1-1 (Invited)
Quantum Phase Transition in Mesoscopic Superconductors
1,2
Shiping Zhou, 1 Wan Lee, 1,2Guo-Qiao Zha,
1
Department of Physics, Shanghai University
2
Shanghai Key Laboratory of High Temperature Superconductors, Shanghai
13:50 PM F1-2 (Invited)
Determination of Level Populations in Superconducting Phase Qutrits
Shi Ping Zhao
Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of
Sciences, Beijing, China
14:10 PM F1-3 (Invited)
An Efficient and Polarization Sensitive SNSPD with Coupled Asymmetric SRR-loaded Cavity
Biaobing Jin , Mengmeng Yang, Fan Zheng, Guanghao Zhu,
Research Institute of Superconductive Electronics, School of Electronic Science and Engineering,
Nanjing University
14:30 PM F1-4 (Invited)
Experimental Study of Ultra-low Field Nuclear Magnetic Resonance and Imaging with HTS SQUID
Detector
35
Dongning Zheng
Institute of Physics, Chinese Academy of Sciences, Beijing, China
14:50 PM F1-5
The Application of Magnetic Random Access Memory in Remote Sensing Camera
Xu Zhang, Tao Liu, Dapeng Zhang, Hua Wang, Shourong Zhang
Beijing Institute of Space Mechanics & Electricity
15:05 PM F1-6
Fabrication and Measurements of DC SQUID based on Nb/Al-AlOx/Nb Tunnel Junctions
1
Liliang Ying, 1,2Wei Xiong, 1,3Hai Wang, 1Guofeng Zhang, 1,2,3Zhen Wang
1
Shanghai Institute of Microsystem and Information Technology, CAS
2
Shanghai Tech University
3
University of Chinese Academy of Sciences
Session H1 Modeling, Analysis and Design I
13:30 PM to 15:25 PM, Saturday, November 21, 2015, Lecture Hall 6
Chairs: Shuhong Wang and Zhizhen Liu
13:30 PM H1-1 (Invited)
AC Losses Calculation of High Temperature Superconductor Axial Flux Electric-dynamic Levitation
Motor
1
Shuo Li, 2Yu Fan, 2Jin Fang, 3Duxing Chen
1
College of information science and engineering, Northeastern University
2
School of electrical engineering, Beijing Jiaotong University
3
Barcelona autonomous university, Barcelona, Spain
13:50 PM H1-2 (Invited)
Six-Sigma Robust Topology and Shape Optimizationfor Flux Switching Permanent Magnet
Machines
1
Gang Lei, 1Youguang Guo, 1Jianguo Zhu, 2Wei Xu,
1
School of Electrical, Mechanical and Mechatronic Systems, University of Technology, Sydney,
Australia
2
School of Electrical and Electronic Engineering, Huazhong University of Science and Technology
14:10 PM H1-3
Rotational Magnetic Properties of Silicon Steel Laminations By 3-D Magnetic Properties
Measurement
1
Yongjian Li, 1Lei Cao, 1Changgeng Zhang, 2Qingxin Yang
1
Province-Ministry Joint Key Laboratory of Electromagnetic Field and Electrical Apparatus
Reliability,Hebei University of Technology
2
Tianjin Key Laboratory of AEEET, Tianjin Polytechnic University
14:25 PM H1-4
Magnetic Levitation Characteristics of 3-DOF Deflection Type PM Motor
1
Zheng Li, 2Qunjing Wang
1
School of Electrical Engineering, Hebei University of Science and Technology
2
Collaborative Innovation Center of Industrial Energy Saving and Power Quality Control, Anhui
University
14:40 PM H1-5
An Efficient Conformal Mapping Method for Air-gap Magnetic Field Analytical Calculation in An
Eccentric Magnetic Harmonic Gear
Ronghui Liu, Zhang Yuejin
36
School of Mechatronics Engineering and Automation, Shanghai University
14:55 PM H1-6
Analysis and Calculation of Eddy Current Braking Force for An Ironless Linear Synchronous Motor
with Cooling System
Lu Zhang, Baoquan Kou, Yusheng Chen
Department of Electrical Engineering, Harbin Institute of Technology
15:10 PM H1-7
The Prediction of Energy-saving Electromagnetic Flowmeter based on Kalman Filtering Method
Xiaoguang Huang, Shihong Yue, Hao Zhang, Benyuan Sun
School of Electrical Engineering and Automation, Tianjin University
Session A2 Materials II
15:40 PM to 17:35 PM, Saturday, November 21, 2015, Lecture Hall 2
Chairs: Yiyuan Xie and Surgey Samoilenkov
15:40 PM A2-1 (Invited)
Hydrostatic Pressure Induced Significant Enhancement of Critical Current Density by Orders of
Magnitude in Iron Pnictide Superconducting Tapes, Granular Bulks and Single Crystals
Xiaolin Wang
Institute for Superconducting and Electronic Materials, Faculty of Engineering, Australian Institute
for Innovative Materials, University of Wollongong, North Wollongong, Australia
16:00 PM A2-2 (Invited)
Evolution of Morphology and Residual Stress of GdBa2Cu3O7-δ/EuBa2Cu3O7-δ Quasimultilayers
Jianxin Lin, Xuming Liu, YanqunGuo, Feng Fan, Yuming Lu, Chuanyi Bai, Zhiyong Liu, Chuanbing Cai
Shanghai Key Laboratory of High Temperature Superconductors, Department of physics, Shanghai
University
16:20 PM A2-3
Influence of Interface Reactions on the YBCO Films Grown by Fluorine-free Solution Rounte
1,2
Yue Zhao, 2Xiao Tang, 1Wu Wei, 2Jean-Claude Grivel
1
Department of Electrical Engineering, Shanghai Jiaotong University
2
Department of Energy Conversion and Storage, Technical University of Denmark, Denmark
16:35 PM A2-4
Study on Quantitative Pulse Magnetization of NdFeB
Zhihua Chen, Junquan Chen
National Key Laboratory of Science and Technology on Vessel Integrated Power SystemNavel
University of Engineering, Wuhan
16:50 PM A2-5
Fabrication and Properties of Tl-2212 Films on CeO2-Buffered Sapphire Substrates
1
Qinglian Xie, 2Shaolin Yan, 3Hongwei Yue, 2Lu Ji, 1Guohua Huang, 1Yuqing Fang, 2Xinjie Zhao, 2Lan
Fang
1
College of Physics and Electronic Engineering, Guangxi Teachers Education University, Nanning
2
Department of Electronics, Nankai University, Tianjin
3
School of Information and Communication, Guilin University of Electronic Technology, Guilin
17:05 PM A2-6
Anomalous Thermal Expansion of PrBCO Compounds Revisited at Low Temperatures
1
Mahieddine Lahoubi, 2Shengli Pu, 2Delong Su
1
Department of Physics, Laboratory L.P.S. Faculty of Science, Badji Mokhtar Annaba
University,Annaba, Algeria
2
College of Science University of Shanghai for Science and Technology, Shanghai
37
17:20 PM A2-7
Quantity Analysis On The Thermal Stability of LTS/HTS Composite Superconducting Wire
Yingmin Cui, Yin Shun Wang, Gang Lu
North China Electric Power Univeristy
Session D2 Electrical Machines
15:40 PM to 17:35 PM, Saturday, November 21, 2015, Grand Auditorium
Chairs: Quan Li and Daohan Wang
15:40 PM D2-1 (Invited)
Development of Electric Motors with Soft Magnetic Composite Materials
1
Youguang Guo, 1Jianguo Zhu, 2Jianxun Jin
1
Faculty of Engineering and Information Technology, University of Technology Sydney, Sydney,
Australia
2
School of Electrical Engineering and Automation, Tianjin University, Tianjin
16:00 PM D2-2 (Invited Talk)
Interior Permanent Magnet Motor Parameter Analysis and Flux-weaken Drive for EV Traction
Yue Zhang, Wenping Cao, John Morrow
School of Electronics, Electrical Engineering and Computer Science, Queens University, Belfast,
Belfast, UK
16:20 PM D2-3
MPPT Control of a Novel Axial flux Permanent Magnet Machine for Wind Power Generation
1
Xiang Luo, 2Shuangxia Niu
1
School of Naval Architecture, Ocean & Civil Engineering, Shanghai Jiao Tong University, Shanghai
2
Department of Electrical Engineering, The Hong Kong Polytechnic University, Hongkong, China
16:35 PM D2-4
Torque Ripple Reduction for Interior Permanent Magnet Machines Using Overlapped windings
with Fractional Slot Per Pole Pair
Jing Rao, Ronghai Qu, Dawei Li, Yuting Gao
State Key Laboratory of Advanced Electromagnetic Engineering and Technology,
College of Electrical & Electronic Engineering, Huazhong University of Science and Technology,
Wuhan
16:50 PM D2-5
A Novel Structure of Rotating PM Vernier Permanent Magnet Machine
Yunchong Wang, W. N. Fu, Shuangxia Niu, S. L. Ho
The Hong Kong Polytechnic University, Hong Kong
17:05 PM D2-6
A Novel Variable-Flux Pole-Changing Permanent Magnet Memory Machine
Dong Wang, Heyun Lin, Hui Yang, Yang Zhang, Kaikai Guo, Yunkai Huang
Engineering Research Center for Motion Control of Ministry of Education
Southeast University
17:20 PM D2-7
Analyze of Permanent Magnet Loss of High Speed Permanent Magnet Synchronous Motor for
Flywheel Energy Storage System
Gengji Wang, Ping Wang, Xiaoyuan Wang
School of Electrical Engineering and Automation, Tianjin University, Tianjin
Session F2 Electronics II
38
15:40 PM to 17:35 PM, Saturday, November 21, 2015, Lecture Hall 4
Chairs: Haiwen Liu and Bin Wei
15:40 PM F2-1 (Invited)
Design of Dual-Band Superconducting Bandpass Filter Using Dual-Mode Hairpin Ring Resonator
Haiwen Liu
Department of Information Engineering, East China Jiaotong University, Nanchang
16:00 PM F2-2 (Invited)
The Progress of Thallium HTS Filters in China
Lu Ji
Department of Electronics, Nankai University, Tianjin
16:20 PM F2-3 (Invited)
Development of Superconducting Filters and Applications in Wireless Communication Systems
Bin Wei, Bisong Cao, Xubo Guo, Xiaoping Zhang
Department of Physics, Tsinghua University, Beijing
16:40 PM F2-4 (Invited)
Developments of Ultra-narrowband High Temperature Superconducting Bandpass Filters
Liang Sun, Chunguang Li, Tao Yu, Lu Gao, Yun Wu, Jia Wang, Yongbo Bian, Xueqiang Zhang, Hong Li,
and Yusheng He
Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of
Sciences, Beijing
17:00 PM F2-5
Design and Implementation of Low-Phase-NoiseTemperature-Compensated Crystal Oscillator
Junjie Jiao, Xianhe Huang, Wei Fu
School of Automation Engineering, University of Electronic Science and Technology of China,
Chengdu
17:15 PM F2-6
Design and Analysis of a Novel Axial Field Flux-Switching Memory Machine Suitable for Variable
Speed Operation
Mingyao Lin, Nian Li, Da Xu, Lei Xu, Wei Zhang
School of Electrical Engineering, Southeast University, Nanjing
Session H2 Modeling, Analysis and Design II
15:40 PM to 17:35 PM, Saturday, November 21, 2015, Lecture Hall 6
Chairs: Yongjian Li and Jin Fang
15:40 PM H2-1 (Invited)
Extended Finite Element Method for Electromagnetic Fields
1
Na Na Duan, 1,2Wei JieXu, 1Shu Hong Wang, 2Jian Guo Zhu, 2You Guang Guo
1
State Key Laboratory of Electrical Insulation and Power Equipment, School of Electrical
Engineering, Xi’an Jiaotong University, Xi’an
2
School of Electrical, Mechanical and Mechatronic Systems,
University of Technology, Sydney, Australia
16:00 PM H2-2 (Invited)
Numerical Modeling of Pinning and Skin Effects in Silicon Steel Plate Using Finite Element
Method
1
Haiyang Kong, 1Fuxin Fang, 1Weimin Guan, 2Yanhui Gao, 2Kazuhiro Muramatsu
1
School of Electrical Engineering, Wuhan University, Wuhan
2
Department of Electrical and Electronic Engineering, Saga University, Saga Japan
39
16:20 PM H2-3
A Novel Method for Fault-tolerant NoC with FPGA
1
Zhi Lu, 1Shuyan Jiang, 1Chao Wu, 1Guoming Song, 2Gang Luo, 2Qi Li
1
School of Automation Engineering,University of Electronic Science and Technology of China,
Chengdu
2
Chengdu Technological University, Chengdu
16:35 PM H2-4
The MTPA Control Based on Gradient Torque Limit of the IPMSM Vector Control System
Qunzhang Tu, Jiakun Lin, Xia Feng, Kejun Duan
College of Field Engineering, PLA Univ. of Sci. & Tech, Nanjing
16:50 PM H2-5
New Model Predictive Current Control Strategy Based Rotor Flux for Linear Induction Machines
Wei Xu, Jianqiao Zou
School of Electrical and Electronic Engineering, Huazhong University of Science and Technology
17:05 PM H2-6
Performance Simulation of Flux Modulation Permanent Magnet Machines With Three Topologies
1
HuiJuan Liu,1Yue Hao,2Shuangxia Niu, 1Jingxiong Zhang
1
School of Electrical Engineering, Beijing Jiaotong University, Beijing
2
Dept. of Electrical and Electronic Engineering, The Hong Kong Polytechnic University, Hong Kong
17:20 PM H2-7
Permanent Magnet Reduction of IPMSM on Efficiency Map Simulation
Jing juan Du, Xiaoyuan Wang, Haiying Lu
School of Electrical Engineering and Automation, Tianjin University, Tianjin
Session B1 Superconducting Electric Power Devices I
9:45 AM to 12:10 PM, Sunday, November 22, 2015, Grand Auditorium
Chairs: Rene Fuger and Shaotao Dai
9:45 AM B1-1 (Invited)
Development of 35kV/1kA Three-phase HTS Power Cable
Nobuhiro Midou
SWCC SHOWA HOLDINGS CO., LTD., Japan
10:05 AM B1-2 (Invited)
Development of 35kV 2000A CD HTS cable demonstration project
Xihua Zong, Dong Wei, Yunwu Han, Tao Tang, Zhiyong Zhang, Zhiguang Yu
Shanghai Electric Cable Research Institute
Superconducting Project Techonlogies Research Centre, Shanghai
10:25 AM B1-3
Inductance Evaluation of a 22.9 kV/50 MVA HTS Cable with Shield by Electrical Method
1
Z.Y. Li, 1D. Hu, 1Z. Yao, 1Y. Wang, 1Z. Hong, 2K. Ryu, 3Y.H. Ma, 4H.S. Yang
1
Department of Electrical Engineering, Shanghai Jiao Tong University Shanghai
2
Department of Electrical Engineering, Chonnam National University, Gwangju, Korea
3
Division of Electronics and Communication Engineering, Yanbian University, Yanji
4
Korea Electric Power Research Institute Daejeon, Korea.
10:40 AM B1-4
Current Imbalance and AC Losses of Long Distance DC HTS Cable
40
38
1
Yury V. Ivanov, 1Vladimir S. Vyatkin, 1Hirofumi Watanabe, 1Noriko Chikumoto, 1Makoto Hamabe,
1
Jian Sun, 1Hirohisa Takano, 1Satarou Yamaguchi, 2Edmund S. Otabe
1
Center of Appl. Supercond. & Sustainable Energy Research, Chubu University, Kasugai Japan
2
Dept. of Computer Science and Electronics, Kyushu Institute of Technology, Iizuka Japan
10:55 AM B1-5
Influences of Terminal Current on Critical Current of DC HTS Cable with Large Current Capacity
1
Han Zhang, 2Yinshun Wang
1
Key Laboratory of HV and EMC Beijing, University of North China Electric Power, Beijing
2
State Key Laboratory for Alternate Electrical Power System with Renewable Energy Source,
University of North China Electric Power, Beijing
11:10 AM B1-6
Electromagnetic Design of A High Temperature Superconductivity
Controllable-Reactor
S. Shen, Y. Tang, L. Ren, H. Dong, X. Zhao, Z. Wang
State Key Laboratory of Advanced Electromagnetic Engineering and Technology Huazhong
University of Science and Technology, Wuhan
11:25 AM B1-7
Heat Generation and Temperature Rise in a Resistive Type Superconducting Fault Current Limiter
Yaxiong Tan, Kun Yang, Bin Xiang,
Jing Yan, Zhiyuan Liu, Yingsan Geng, Jianhua Wang, Satoru Yanabu
State Key Laboratory of Electrical Insulation and Power Equipment, Xi’an Jiaotong University, Xi’an
11:40 AM B1-8
Optimized Design of the Saturated Iron Core Superconducting Fault Current limiter
Ziqiang Wei, Ying Xin, Jianxun Jin
Tianjin University, Tianjin
11:55 AM B1-9
Improved Discretization-based Decoupled Feedback Control for Series Connected Converter of
SCC
Jing Shi, Kang Gong, Yang Liu, Xiao Zhou, Yuejin Tang, Li Ren, Jingdong Li
State Key Laboratory of Advanced Electromagnetic Engineering and Technology, Huazhong
University of Science and Technology
Session C Electrical Power Systems
9:45 AM to 12:10 PM, Sunday, November 22, 2015, Lecture Hall 2
Chairs: Bin Li and Lei Chen
9:45 AM C-1 (Invited)
The application of Superconductive Fault Current Limiter in VSC-HVDC System
Botong Li, Jia Jian Fei, Li Bin, Zhang Yun Ke
Key Laboratory of Power System Simulation and Control of Ministry of Education, Tianjin University,
Tianjin
10:05 AM C-2 (Invited)
Low-Voltage Ride-Through Capability Enhancement of DFIG-Based Wind Turbine With a
Resistive-Type SFCL Connected in Series With Rotor Winding
1
Zhi-Ce Zou, 1Xian-Yong Xiao, 1Ran Ou, 2Yi Zhang, 1Chang-Song Li
1
College of Electrical Engineering and Information Technology Sichuan University, Chengdu
2
State Grid Fujian Electric Power research Institute, State Grid Corporation of China, Fuzhou
41
10:25 AM C-3
Analysis and Design of a Novel Linear Generator for Hervesting Oceanic Wave Energy
1
Omar Farrok, 1M. Rafiqul Islam Sheikh, 1M. Rabiul Islam, 2Wei Xu, 3Youguang Guo, 3Jianguo Zhu
1
Department of Electrical and Electronic Engineering, Rajshahi University of Engineering and
Technology Rajshahi-6204, Bangladesh
2
HUST, Wuhan
3
UTS, NSW 2007, Australia
10:40 AM C-4
Cumulative Deformation Analysis of Transformer Winding under Short-Circuit Fault Using 3-D
FEM
1
Hai Jun Zhang，2Shu Hong Wang
1
Faculty of Electrical Engineering, Xi’an Jiaotong University
2
Faculty of Hydroelectric Power, Hebei University of Engineering
10:55 AM C-5
Superconducting Magnetic Energy Storage Based Power System Control Using Adaptive Dynamic
Programming
1
Yufei Tang, 1Haibo He，2Chaoxu Mu
1
Department of Electrical and Computer Engineering, University of Rhode Island, Kingston, RI, USA
2
School of Electrical and Automation Engineering, Tianjin University, Tianjin
11:10 AM C-6
Microgrid Stabilization by SMES with SOC Control
1
Issarachai Ngamroo, 2Sitthidet Vachirasricirikul
1
Department of Electrical Engineering, King Mongkut’s Institute of Technology Ladkrabang,
Bangkok, Thailand
2
School of Engineering, University of Phayao, Phayao, Thailand
11:25 AM C-7
Comparative Study of Inductive and Resistive SFCL to Mitigate the DC Fault Current in a
VSC-HVDC System Integrated with Wind Power Farms
Lei Chen, Fei Tang, Li Ren
School of Electrical Engineering, Wuhan University, Wuhan
11:40 AM C-8
Design and Loss Analysis of the High Frequency PFC Converter
Qiang Li, Huaiyou Zhao, Kai Yao
Nanjing University of Science and Technology
11:55 AM C-9
A Novel Control Technology Based on Viutual Synchronous Generator Applied in Microgrid
1
Haishi Zhang, 2Xiao Yuan Chen
1
Department of Electrical Engineering, Southwest Jiaotong University
2
Sichuan Normal University, Chengdu
Session E1 Magnets I
9:45 AM to 12:10 PM, Sunday, November 22, 2015, Lecture Hall 4
Chairs: Qiang Li and Li Ren
9:45 AM E1-1 (Invited)
Development of High Magnetic Field Magnet Technologies for the Magnetic Resonance Medical
Imaging
Qiuliang Wang, Wenhui Yang, Feng Liu, Ling Xia, Yi Li, Zhipeng Ni, Luguang Yan, Jianyi Xu, Junsheng
Cheng, Hui Wang
42
Institute of Electrical Engineering, Chinese Academy of Sciences, Beijing
10:05 AM E1-2 (Invited)
The Design and Progress of the Superconducting Magnet System for CFETR
Qiang Li
Institute of Plasma Physics, Chinese Academy of Sciences, Hefei
10:25 AM E1-3
Study on HTS/LTS Hybrid Superconducting Central Solenoid for Fusion Device
1
Jinxing Zheng, 1Yuntao Song, 2Rui Kang, 2Lei Wang
1
Institute of Plasma Physics, Chinese Academy of Sciences
2
School of Nuclear Science and Technology, University of Science and Technology of China
10:40 AM E1-4
Optimal Design of Magnetic Gears with A General Pattern of Permanent Magnet Arrangement
W. N. Fu, Longnu Li
Department of Electrical Engineering, The Hong Kong Polytechnic University
10:55 AM E1-5
Development of an LTS/HTS Hybrid Superconducting Magnet
Wei Pi, Yingmin Cui, Yinshun Wang, Jin Dong
North China Electric Power University, Beijing
11:10 AM E1-6
Development of YBCO Insert for a 25 T Superconducting Magnet all
Jianhua Liu, Shouseng Song, Chenchen Gou, Jianbo Zhou, Lei Wang, Yi Li, Yinming Dai
Institute of Electrical Engineering, Chinese Academy of Science, Beijing
11:25 AM E1-7
Experimental Study on Temperature and of Peltier Current Leads Heatleakage
1
Guixin Chen, 1Yinshun Wang, 2Wei Pi
1
State Key Laboratory of New Energy Renewable Power System, North China Electric Power
University, Beijing
2
Beijing Key Laboratory of High Voltage and Electromagnetic Compatibility, North China Electric
Power University, Beijing
11:40 AM E1-8
Identification and Mixed-Sensitivity H∞ Control of Permanent Magnet Biased Axial Magnetic
Bearing with Multiple Air Gaps
1
Zhenzhong Su, 1Dong Wang, 2Kang Wang, 1Leitao Wu, 1Xianbiao Zhang
1
National Key Laboratory of Science and Technology on Vessel IPS, Naval University of Engineering
2
Engineering Research Center for Motion Control of Ministry of Education, Southeast University
11:55 AM E1-9
Mechanical Properties of HTS Magnet for a 5MJ SMES Using Coated Conductor on Round Core
1
Guolei Ma, 1Yinshun Wang, 2Zhu Jiahui, 2Li Zhenming, 2Liu Wei, 2Qiu Ming
1
State Key Laboratory of New Energy Renewable Power System, North China Electric Power
University, Beijing
2
Electrical Engineering and New Material Department, China Electric Power Research Institute,
Beijing
Session G Cryogenics and Thermal/Electrical Insulation
9:45 AM to 12:10 PM, Sunday, November 22, 2015, Lecture Hall 6
Chairs: Naoki Hayakawa and Boxue Du
9:45 AM G-1 (Invited)
Recent Development of Small-scale Stirling Cycle based Cryocoolers
43
Wei Dai
Key laboratory of Cryogenics, Chinese Academy of Sciences, Beijing
10:05 AM G-2 (Invited)
Cryogenic Electrical Insulation - Common Techniques for Superconducting Power Application
Naoki Hayakawa
Department of Electrical Engineering and Computer Science, Nagoya University, Japan
10:25 AM G-3
Effects of Low Temperature on Dielectric Properties of Ethylene-propylene-diene Terpolymer
Filled with Carbon Black Nanoparticles
J. Li, B. X. Du, Y. Q. Xing, J. X. Jin
School of Electrical Engineering and Automation, Tianjin University, Tianjin
10:40 AM G-4
Helium Boil-off Experiments for a Superconducting Magnet Cryostat with Pulse Tube Cryocoolers
Kun Chang, Bao Zhi Zhao, Shun Zhong Chen
Institute of Electrical Engineering, Chinese Academy of Sciences, Beijing
10:55 AM G-5
Effect of Epoxy Insulation on Strain Distribution in Superconducting Coil
Guang Zhu, Junsheng Cheng, Lankai Li, Jianhua Liu, Jianbo Zhou, Yinmin Dai
Division of Superconducting Magnet Science and Technology, Institute of Electrical Engineering,
CAS
11:10 AM G-6
Developing Process of Partial Discharge in Oil-Paper Insulation Under Needle-Plate Defects
1
Yanjie Cui, 1Lingyu Zhu, 1Shengchang Ji, 2Xiaobo Ou, 2Dan Zhou, 2Chunyao Lin
1
State Key Laboratory of Electrical Insulation and Power, Xi’an Jiaotong University, Xi’an
High Voltage Technology Research Department, Guangdong Electric Power Research Institute
Guangzhou
2
11:25 AM G-7
Comparison Between KAPTON Polyimide Insulation Layers and Nylon Plates in Superconducting
Tapes Winding
Kun Yang, Yaxiong Tan, Bin Xiang, Zhiyuan Liu, Yingsan Geng, Jianhua Wang, Satoru Yanabu
State Key Laboratory of Electrical Insulation and Power Equipment, Xi’an Jiaotong University
11:40 AM G-8
Effect of Low Temperature on Tree Characteristics in Silicone Rubber under Repetitive Pulse
Voltage
1
T. Han, 1B. X. Du, X. 2X. Cheng, 2Y. Zhang
1
School of Electrical Engineering and Automation, Tianjin University
2
State Grid Tianjin Electric Power Company
11:55 AM G-9
Effect of Direct Fluorination on Surface Potential Behavior of Polyimide Film under Low
Temperature
1
B. X. Du,1Y. Q. Xing,1J. X. Jin, 2J. W. Zhang, 2M. Xiao
1
School of Electrical Engineering and Automation, Tianjin University, Tianjin
2
Jinan Power-supply Company
Session B2 Superconducting Electric Power Devices II
13:30 PM to 15:30 PM, Sunday, November 22, 2015, Lecture Hall 2
Chairs: Yinshun Wang and Guangtong Ma
13:30 PM B2-1 (Invited)
44
41
Progress of HTC Superconducting Power Technology at IEE
Dai Shaotao
Institute of Electrical Engineering, Chinese Academy of Sciences, Beijing
13:50 PM B2-2 (Invited)
Superconducting Motor Developments at Guina Energy Technologies
Rene Fuger, Ante Guina, David Sercombe, John Kells, Arkadiy Matsekh, Kurt Labes, Tony Lissington,
Cesimiro Fabian, Grace Chu
Guina Energy Technologies PTY LTD, Surfers Paradise, Australia
14:05 PM B2-3
Dynamic longitudinal edge effect of high-temperature superconducting linear induction motor
Liu Bin, Xiaoyue Zhang, Jin Fang
School of Electrical Engineering Beijing Jiaotong University, Beijing
14:20 PM B2-4
Multilevel Robust Optimization of a Superconducting Magnetic Energy Storage Based on Design
for Six-Sigma
1
Gang Lei, 1Youguang Guo, 1Jianguo Zhu, 2Wei Xu
1
School of Electrical, Mechanical and Mechatronic Systems, University of Technology, Sydney,
Australia
2
School of Electrical and Electronic Engineering, Huazhong University of Science and Technology,
Wuhan
14:35 PM B2-5
Structural Effect of the Permanent Magnet Guidewayon the Dynamic Behavior of a Levitated
HighTemperature Superconductor
Kun Liu, Chang-Qing Ye, Guang-Tong Ma, Han Zhang, Xing-Tian Li, Chen Yang, Peng-Bo Zhou,
Zhi-Tao Wang, Tian-Yong Gong, J. S. Wang
Southwest Jiaotong University, Chengdu
14:50 PM B2-6
Magnetic - Thermal Coupling Analysis of Air-Core Reactor in EAST Fast Control Power Supply
Yunpeng Hu, Xiaohua Bao, Cheng Zhang, Yuanyang Chen
School of the Electrical Engineering and Automation, Hefei University of Technology, Hefei
15:05 PM B2-7
Arcing Time in A SuperconductingCurrent-Limiting Type DC Circuit Breaker
Bin Xiang, Licai Zhang, Yaxiong Tan, Kun Yang, Zhiyuan Liu, Yingsan Geng, Jianhua Wang, S.Yanabu
State Key Laboratory of Electrical Insulation and Power Equipment, Xi’an Jiaotong University, Xi’an
15:20 PM B2-8
Analysis of Driving Torque Generated by Superconducting Motor Based on the Meissner Effect
Chunyan Cui, Lankai Li, Xinning Hu, Hui Wang, Qiuliang Wang
The Institute of Electrical Engineering of Chinese Academy of Sciences
Session D3 Electrical Machines III
13:30 PM to 15:30 PM, Sunday, November 22, 2015, Grand Auditorium
Chairs: Dawei Li and Wei Zhang
13:30 PM D3-1
The Analysis and Compensation Control of the Detent Force for Slot-less Tubular Permanent
Magnet Linear Synchronous Motor
Qinglong Wang, Xuzhen Huang, Bo Zhou, Qiang Tan, Jing Li
Nanjing University of Aeronautics and Astronautics, Nanjing
13:45 PM D3-2
45
A Novel Active Boost Power Converter with Application to Toruqe Ripple Reduction Control for
Switched Reluctance Motor
Chao Zhang, Shu Hui Zhang, Kun Wang
College of Electrical and Information Engineering, Jiangsu University, Zhenjiang
14:00 PM D3-3
Drive System Design and Experiment Validation of 3-DOF Deflection Type PM Motor
1
Zheng Li, 2Qunjing WANG
1
School of Electrical Engineering, Hebei University of Science and Technology, Shijiazhuang
2
Collaborative Innovation Center of Industrial Energy Saving and Power Quality Control, Anhui
University, Hefei
14:15 PM D3-4
An Upgraded Soft Winding Machines based on Advanced Yarn Tension Modelling
1
Mohamed Hassan Ali, 1H.E.A. Ibrahim, 1Noha H. El-Amary, 2Raafat Ibrahim Mashaly
1
Electrical and Control Engineering Department,Arab Academy for Science Technology and
Maritime Transport,El Moshir Ismail Street - behind Sheraton Building,Cairo, Egypt
2
Textile Engineering Department,Alexandria University,Lotfy El-Sied Street off Gamal Abd
El-Naser,Alexandria, Egypt
14:30 PM D3-5
Harmonic Impact on Rotor Losses in Fault-Tolerant Interior Permanent-Magnet Machines
Junqiang Zheng, Wenxiang Zhao, Jinghua Ji
School of Electrical and Information Engineering Jiangsu University, Zhenjiang
14:45 PM D3-6
Topology Analysis and Performance Evaluation of a High Thrust Force Density Linear Switched
Reluctance Machine
Daohan Wang, Xiuhe Wang, Chenghui Zhang
Shandong University, Jinan
15:00 PM D3-7
Analysis and Design of An Ironless Linear Synchronous Motor with Double-side Halbach
Permanent Magnet Array
Lu Zhang, Baoquan Kou
Department of Electrical Engineering, Harbin Institute of Technology, Harbin
15:15 PM D3-8
Calculation and Measurement of Electromagnetic Parameter for High Speed Slotless PM Motors
Peng Gao, Xiaoyuan Wang
School of Electrical Engineering and Automation, Tianjin University, Tianjin
Session E2 Magnets II
13:30 PM to 15:30 PM, Sunday, November 22, 2015, Lecture Hall 4
Chairs: Qiuliang Wang and W. N. Fu
13:30 PM E2-1 (Invited)
Cost Reduction of Vernier Permanent-Magnet Machine With Ferrite Magnets
Ming Chen, Guohai Liu, Wenxiang Zhao, Qian Chen, Wanxiang Zhao
School of Electrical and Information Engineering, Jiangsu University, Zhenjiang
13:50 PM E2-2
Comprehensive Magnetic Properties Measurement of the Silicon Steel Considering the
Laminated Direction
1
Yong Jian Li, 1Qing Xin Yang, 1Chang Geng zhang, 2Jian Guo Zhu, 2You Guang Guo
46
1
Province-Ministry Joint Key Laboratory of Electromagnetic Field and Electrical Apparatus Reliability,
Hebei University of Technology
2
School of Electrical, Mechanical and Mechatronic Systems, University of Technology Sydney,
Sydney, NSW 2007, Australia
14:05 PM E2-3
A Flux-Concentrating External-Rotor Switched Flux Hybrid Magnet Memory Machine for
Direct-Drive Automotive Applications
1
Hui Yang, 1Heyun Lin, 1Dong Wang, 1Kaikai Guo, 1Shuhua Fang, 1Yunkai Huang, 2Hui Yang, 2Z. Q.
Zhu
1
Engineering Research Center for Motion Control of MOE, Southeast University, Nanjing
2
Department of Electronic and Electrical Engineering, University of Sheffield, Sheffield S1 3JD, U.K
14:20 PM E2-4
A Novel Passive Shimming Method for 0.7T Biplanar Superconducting MRI
Xuchen Zhu, Houshen Wang, Hui Wang, Yi Li
Key Laboratory of Applied Superconductivity, Institute of Electrical Engineering, Chinese Academy
of Sciences, Beijing
14:35 PM E2-5
Preliminary AC loss analysis for the CFETR Central Solenoid Model Coil
1
W. Zhou, 1J. Fang, 2A. Nijhuis
1
School of Electrical Engineering, Beijing Jiaotong University, Beijing
2
Energy, Materials and Systems Group University of Twente Enschede, The Netherlands
14:50 PM E2-6
IBEM Applied to the Design of Gradient Coils for Superconducting MRI
Yang Hu, Xinning Hu, Luguang Yan, Feng Liu
Institute of Electrical Engineering, Chinese Academy of Sciences, Beijing
15:05 PM E2-7
Effect of LTS Background Coil Size on The Ac Loss Generated in the REBCO HTS Insert Magnet
Lei Wang, Jianhua Liu, Hui Wang, Chenchen Gou, Jianbo Zhou
Key Laboratory of Applied Superconductivity, Institute of Electrical Engineering, Chinese Academy
of Sciences, Beijing
15:20 PM E2-8
Numerical Computation of Static Magnetic Field Considering 2D Property of Silicon Steel
Youxing Xiong，Junquan Chen
National Key Laboratory of Science and Technology on Vessel Integrated Power System, Naval
University of Engineering, Wuhan
Session H3 Modeling, Analysis and Design III
13:30 PM to 15:30 PM, Sunday, November 22, 2015, Lecture Hall 6
Chairs: Youguang Guo and Wei Xu
13:30 PM H3-1
Maximum Power Point Tracking Strategy for Photovoltaic System Based on Probability
1
Wei Xu, 2Lei Tang, 3Chaoxu Mu
1
School of Electrical and Electronic Engineering, Huazhong University of Science and Technology,
Wuhan
2
School of Electrical Engineering, Xi’an Jiaotong University, Xi’an
3
School of Electrical and Automation Engineering, Tianjin University, Tianjin
13:45 PM H3-2
Two-Dimensional Elemental Operator for Modelingthe Vectorial Hysteresis of Soft Magnetic
Composite Material
47
1
Wei Jie Xu, 1Na Na Duan, 1Shu Hong Wang,2You Guang Guo, 2Jian Guo Zhu
1
State Key Laboratory of Electrical Insulation and Power Equipment, School of Electrical
Engineering, Xi’an Jiaotong University, Xi’an
2
School of Electrical, Mechanical and Mechatronic Systems, University of Technology, Sydney,
Australia
14:00 PM H3-3
Transient Thermal Analysis of the Conical Rotor Motor using LPTN with Accurate Heat Transfer
Coefficients
Baocheng Guo, Yunkai Huang, Jianning Dong
School of Electrical Engineering, Southeast University, Nanjing
14:15PM H3-4
Core Dynamic Hysteresis Model Establishment under DC Flux
Yang Wang, Zhizhen Liu
School of Electrical Engineering Energy, Shandong University, Jinan
14:30PM H3-5
Electromagnetic Design and Research of 2.935MW Permanent Magnet Synchronous Generator
for Wind Turbine
Jiabin Wen, Jinze Li
College of Electrical and Electronic Engineering, Harbin University of Science and Technology
14:45 PM H3-6
Simulation on the Apparatus of Underwater Active Electrolocation
Jun Wu,Jiegang Peng
School of Automation, University of Electronic Science and Technology of China, Chengdu
15:00 PM H3-7
Performance Analysis of a High Power Density Tubular Linear Switch Reluctance Generator for
Direct Drive Marine Wave Energy Conversion
Daohan Wang, Xiuhe Wang, Chenghui Zhang
Shandong University, Jinan
15:15 PM H3-8
Analytical Calculation of PMSG Optimization for Compact ER-EVs Application
1
Lu Haiying, 1Wang Xiaoyuan, 1Du Jingjuan, 2Zhu Lihui
1
Tianjin University, China
2
Citen Communication Tech. Co.LTD
Posters
17:35 PM to 18:20 PM, Saturday, November 21, 2015 and 15:45 PM to 16:30 PM, Sunday, November
22, 2015, Lecture Hall 5A-5B
Chairs: Yanfang Bi and Yusheng He
Session A Materials
ID: 5081 AP-1
Vortex Properties of Nanosized Superconducting Strips with One Central Weak Link under An
Applied Current Drive
1
Lin Peng, 2 Chuanbing Cai
1
Department of Physics, Shanghai University of Electric Power, Shanghai
2
Shanghai Key Laboratory of High Temperature Superconductors, Department of Physics, Shanghai
University
45
ID: 5097 AP-2
Thick Y(Dy)Ba2Cu3O7-d Films Fabricated at Low Pressure by Super-Low-Fluorine MOD Method
Chuanwei Cui, Xuming Liu, Chuanbing Cai
Research Center for Superconductors and Applied Technologies, Physics Department, Shanghai
University
ID: 5099 AP-3
Influence of Magnet Materials on Performances of Fault-Tolerant Permanent-Magnet Vernier
Machines
Xun Fan, Guohai Liu, Liang Xu, Wenxiang Zhao
School of Electrical and Information Engineering, Jiangsu University
ID: 5145 AP-4
Thermal Stability of a Quasi-isotropic Strand Made from Coated Conductors
Tingting Li, Yinshun Wang
State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources, North
China Electric Power University
ID: 5154 AP-5
Analysis of Critical Current of the HTS Strand
Chenjie Shi, Yinshun Wang, Jiawei Li, Tingting Li, Guixin Chen
State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources, North
China Electric Power University
ID: 5156 AP-6
Current Distribution Characteristics of LTS/HTS Hybrid Superconductor
Wei Pi, Yinshun Wang
State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources, North
China Electric Power University
ID: 5174 AP-7
Bending Characterization of an HTS Strand with Geometrical Symmetric Structure
Yinshun Wang, Jinya Miao
State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources, North
China Electric Power University
ID: 5175 AP-8
Critical Current of a Quasi-isotropic HTS Strand with Symmetric Configuration
Yinshun Wang, Yang Li
State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources, North
China Electric Power University
ID: 5185 AP-9
The Thermal Stability of LTS/HTS Composite Round Wire
Ying min Cui, Yin Shun Wang, Gang Lu
State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources, North
China Electric Power Univeristy
ID: 5238 AP-10
Characterization Analysis on Performance of YBaCuO Coils Induced by Steady-state Current
Konghui Liu, Wentao Li, Chuanyi Bai, Haoyu Song, Changxin Chi, Chuanbing Cai
Shanghai Key Laboratory of High Temperature Superconductors, Department of physics, Shanghai
University
ID: 5240 AP-11
Study on PEG assisted TFA-MOD Method for Rapid Fabrication of YBa2Cu3O7−δ Thin Films:
Influence of PEG Additive Amount in Precursor Solution
1
W. Wu, 1Y. Zhao, 1Z. Hong, 2Z. Jin, 3F. Feng
1
Department of Electrical Engineering, Shanghai Jiaotong University
2
Division of Advanced Manufacturing, Graduate School at Shenzhen, Tsinghua University
3
Applied Superconductivity Research Center, Tsinghua University
49
48
ID: 5270 AP-12
Development of Electric Motors with Soft Magnetic Composite Materials
1
Youguang Guo, 1Jianguo Zhu, 2Jianxun Jin
1
Faculty of Engineering and Information Technology, University of Technology Sydney, Sydney,
Australia
2
School of Electrical Engineering and Automation, Tianjin University
ID: 5299 AP-13
Chemical Solution Derived YBa2Cu3.3O7-d/Y(Cu) Multilayers on Oxide Buffered Metallic Tapes
1,2
Chuanwei Cui, 1,2Zhiyong Liu, 1,2Chuanyi Bai, 1Xuming Liu, 2Zhiying 1,2Zhang, 1,2Yuming Lu,
1,2
Yanqun Guo, 1,2Feng Fan, 1,2Chuanbing Cai
1
Shanghai Key Laboratory of High Temperature Superconductors, Physics Department, Shanghai
University
2
Shanghai Creative Superconductor Technologies Co. Ltd.
ID: 5301 AP-14
Twisting Characteristics of a Quasi-isotropic Strands Fabricated by 2G HTS Tapes
1
Jiawei Li, 1Yinshun Wang, 2Ming Li
1
State Key Laboratory of New Energy Renewable Power System, North China Electric Power
University
2
Zhongtian Technology Group Co. Ltd.
ID: 5304 AP-15
Numerical Analysis on RHEED Patterns Based on Gray Level: A Case Study of IBAD-MgO Film
1
Xiaoliang Shi, 1,2Feng Fan, 1,2Yanqun Guo, 1,2Chuanyi Bai, 1,2Yuming Lu, 1,2Zhiyong Liu, 1,2Chuanbing
Cai
1
Shanghai Key Laboratory of High Temperature Superconductors Department of physics, Shanghai
University
2
Shanghai Creative Superconductor Technologies Co. Ltd.
ID: 5317 AP-16
Critical Current of HTS Strand with Geometrical Symmetric Configuration in Magnetic Field
1
Chenjie Shi, 2Yinshun Wang
1
Beijing Key Laboratory of High Voltage and Electromagnetic Compatibility
2
State Key Laboratory of New Energy Renewable Power System
ID: 5320 AP-17
Phase Transition During Sintering Process Before Nucleation of TFA-MOD YBa2Cu3O7-δ Films
Wenzhi Dou, Zhiyong Liu, Jie Yu, Fan Yang, Chuanyi Bai, Yuming Lu, Yanqun Guo, Chuanbing Cai
Shanghai Key Laboratory of High Temperature Superconductors, Department of physics, Shanghai
University
ID: 5322 AP-18
Pyrolysis Induced Surface Morphology Evolution of YBa2Cu3O7-δ Films Prepared by Low-Fluorine
Metal-organic Deposition
Jie Yu, Zhiyong Liu, Suchuan Zhao, Zhaohui Gu, Chuanbing Cai, Chuanyi Bai, Yuming Lu, Yanqun Guo
Shanghai Key Laboratory of High Temperature Superconductors, Department of physics, Shanghai
University
ID: 5328 AP-19
Influence of Annealing Time on 5-layer YBa2Cu3O7-δ Thick Films by Low-Fluorine Metal-organic
Deposition
Fan Yang, Zhiyong Liu, Chuanyi Bai, Yuming Lu, Yanqun Guo, Chuanbing Cai
Shanghai Key Laboratory of High Temperature Superconductors, Department of physics, Shanghai
University
ID: 5390 AP-20
Quantum Phase Transition in Mesoscopic Superconductors
1
Wan Lee, 1,2Guo-Qiao Zha, 1,2Shi-Ping Zhou
50
1
Department of Physics, Shanghai University
Shanghai Key Laboratory of High Temperature Superconductors
ID: 5391 AP-21
Deep Insight into Surface Flatness Based on AFM Images Illustrated by Ni-based Alloy
1,2
Yanqun Guo, 1Changxin Chi, 1Xiaoliang Shi, 1Heng Ren, 1Zhiyong Liu, 1,2Yuming Lu, 1,2Chuanbing
Cai
1
Shanghai Key Laboratory of High Temperature Superconductors, Department of Physics, Shanghai
University,Shanghai
2
Shanghai Creative Superconductor Technologies Co. Ltd.Shanghai
2
Session B Superconducting Electric Power Devices
ID: 5078 BP-1
Magnetic Field analysis of a self-shielding DC HTS Cable with Large Current Capacity
1
Han Zhang, 2Yinshun Wang
1
Key Laboratory of HV and EMC Beijing, University of North China Electric Power
2
State Key Laboratory for Alternate Electrical Power System with Renewable Energy Source,
University of North China Electric Power
ID: 5092 BP-2
Multiobjective Design Optimization for High - Temperature Superconducting Linear Synchronous
Motors with Different Primary Topologies
1
Gang Lei, 1Youguang Guo, 1Jianguo Zhu, 2Wei Xu, 3Jianxun Jin
1
School of Electrical, Mechanical and Mechatronic Systems, University of Technology, Sydney,
Australia
2
School of Electrical and Electronic Engineering, Huazhong University of Science and Technology
3
School of Electrical Engineering and Automation, Tianjin University
ID: 5106 BP-3
Electromagnetic Performance Analysis of Fully Stator-HTS Falult-Tolerant Motors
Yu Zeng, Guohai Liu, Wenxiang Zhao, Qian Chen
School of Electrical and Information Engineering, Jiangsu University
ID: 5109 BP-4
Temperature and Current Distribution of High Temperature Superconducting Cable Itself Under
Large Fault Current
Zhenming Li, Wei Liu, Jiahui Zhu, Ming Qiu, Xiaodong Zheng, Jin Fang
1Electrical Engineering and New Material Department China Electric Power Research Institute
2Electrical Engineering Department Beijing Jiao Tong University
ID: 5111 BP-5
Improving FRT Capability and Alleviating Output Power of DFIG Wind Turbine by SMES-FCL
Issarachai Ngamroo
Department of Electrical Engineering, Faculty of Engineering, King Mongkut’s Institute of
Technology Ladkrabang, Bangkok 10520, Thailand
ID: 5113 BP-6
Integrated Superconducting Coil into PV Generator for Power Smoothing and Voltage Regulation
Worapong Kreeumporn, Issarachai Ngamroo
Electrical Engineering Department, Faculty of Engineering, King Mongkut’s Institute of Technology
Ladkrabang, Bangkok 10520, Thailand
ID: 5140 BP-7
Conceptual Design of the Field Winding for a 12MW offshore Superconducting Wind Generator
Xiaoyu Li, Hailin Wang, Jiayi Li, Li Ren, Yuejin Tang
State Key Laboratory of Advanced Electromagnetic Engineering and Technology, Huazhong
University of Science and Technology
ID: 5155 BP-8
51
Design and Analysis a New Primary HTS Linear Motor for Transportation System
Ruiwu Cao, Yi Jin, Yanze Zhang
Department of Electrical Engineering, Nanjing University of Aeronautics and Astronautics
ID: 5165 BP-9
Comparison of Stator HTS Vernier Machines Having Different Stator and Rotor Pole Numbers
Liang Xu, Guohai Liu, Wenxiang Zhao, Jinghua Ji
School of Electrical and Information Engineering, Jiangsu University
ID: 5184 BP-10
Analysis of High Temperature Superconducting Cable under Fault Current
1
Lu Yin, 1Xuefeng Ma, 1Xuenan Li, 2Xiaodong Zheng, 2Jin Fang, 3Jiahui Zhu, 3Ming Qiu
1
Beijing Electric Power Economic Research Institute
2
School of Electrical Engineering, Beijing Jiaotong University
3
China Electric Power Research Institute
ID: 5197 BP-11
AC Copper Losses Calculation of the Ironless BLDCM used in a Flywheel Energy Storage System
Kai Liu, Xinhe Fu, Mingyao Lin
School of Electrical Engineering, Southeast University
ID: 5198 BP-12
Analysis of a Superconducting Induction Magnetic Levitation device for Hydraulic
Turbo-Generator
1
Jing Liu, 1Hongzhong Ma, 2Lei Huang
1
College of Energy and Electrical Engineering, Hohai University
2
School of Electrical Engineering, Southeast University
ID: 5201 BP-13
Superconducting Liquid Nitrogen Insulated Metal Enclosed Switchgear
Jianhua Wang, Yaxiong Tan, Yingsan Geng, Zhiyuan Liu, Shuhong Wang
State Key Laboratory of Electrical Insulation and Power Equipment, Xi’an Jiaotong University
ID: 5205 BP-14
Resistive Type Superconducting Fault Current Limiter and Current Flowing Time
Yaxiong Tan, Kun Yang, Bin Xiang, Jing Yan, Yingsan Geng, Zhiyuan Liu, S. Yanabu
State Key Laboratory of Electrical Insulation and Power Equipment, Xi’an Jiaotong University
ID: 5215 BP-15
Current Limiting Ratio and Current Distribution Ratio in a DC Resistive Superconducting Fault
Current Limiter
Bin Xiang, Kun Yang, Yaxiong Tan, Zhiyuan Liu, Yingsan Geng, Jianhua Wang, S.Yanabu
State Key Laboratory of Electrical Insulation and Power Equipment, Xi’an Jiaotong University
ID: 5216 BP-16
Voltage Distribution Characteristics of a Resistive Superconducting Fault Current Limiter in DC
systems
Bin Xiang, Zhiyuan Liu, Yingsan Geng, Jianhua Wang, S.Yanabu
State Key Laboratory of Electrical Insulation and Power Equipment, Xi’an Jiaotong University
ID: 5015 BP-17
Feasibility Study of Low-Frequency Superconducting Inductive Coupled Power Transfer System
Xiao Yuan Chen, Long Chen, Ruo-Cheng Huang, Xiao-Yun Jiang, Cheng Gou, Jiang Su, Jie Mao
School of Engineering, Sichuan Normal University
ID: 5234 BP-18
Design and Analysis of Switched Reluctance Motor with High Temperature Superconducting
Windings
Kaihe Zhang, Youtong Fang, Xiaoyan Huang
College of Electrical Engineering, Zhejiang University
ID: 5244 BP-19
52
Electromagnetic Analysis of High Current Carrying Superconducting Cable Consisted of YBCO
Coated Conductor
1
Jiahui Zhu, 1Ming Qiu, 1Shanshan Fu, 2Huiming Zhang, 2Weijia Yuan, 2Min Zhang
1
Department of Electrical Engineering and Novel Material, China Electric Power Research Institute
2
Department of Electronic and Electrical Engineering, University of Bath, Bath, United Kingdom
ID: 5292 BP-20
Analysis of the Output Torque of a Superconducting Torquer for Drift Test
Hao Wang, Xinning Hu, Chunyan Cui, Hui Wang, Jingwen Xu, Chenchen Gou, Jianbo Zhou
The Institute of Electrical Engineering of Chinese Academy of Sciences
ID: 5306 BP-21
Design and Analysis of a Novel Vernier Reluctance Fully Superconducting Synchronous Generator
with LTS Windings for Wind Power Generation
Shaofeng Jia, Ronghai Qu, Jian Li, Haiyang Fang, Dawei Li, Jingxuan Hu
State Key Laboratory of Advanced Electromagnetic Engineering and Technology, School of
Electrical and Electronic Engineering, Huazhong University of Science and Technology
ID: 5334 BP-22
Topologies for Fully Superconducting Machines
Feng Lin, Ronghai Qu, Dawei Li
The State Key Laboratory of Advanced Electromagnetic Engineering and Technology, School of
Electrical and Electronic Engineering, Huazhong University of Science and Technology
ID: 5354 BP-23
A Study of a SMES in Smart Grid with Electric Vehicle
Shan C. Wang, Jian X. Jin, Ying L. Wang
Center of applied superconductivity and electrical engineering, school of automation engineering,
University of electronic science and technology of China
ID: 5360 BP-24
Operating Parameters Optimization of SMES Considering Transient Thermal Stability
Kang Gong, Jing Shi, Yang Liu, Lihui Zhang, Li Ren, Xiao Zhou, Aobo Zhou
State Key Laboratory of Advanced Electromagnetic Engineering and Technology, Huazhong
University of Science and Technology, Wuhan
ID: 5376 BP-25
Experimental and Numerical Study on An HTS Air Core Transformer With Pancake Structure
D. Hu, J. Sheng, Z. Y. Li, Z. Hong, Z. Jin
Department of Electrical Engineering, Shanghai Jiao Tong University, Shanghai, China
ID: 5382 BP-26
Research of the Loss of the Corrugated Stainless Steel Pipe in HTS Cable
Xize Zhang, Yunwu Han
Shanghai Electric Cable Research Institute, Superconducting Project Technologies Research Centre,
Shanghai, China
ID: 5384 BP-27
HTS Calbe Control System and Running Situation
Dayi Zhang, Dong Wei
Shanghai Electric Cable Research Institute, Superconducting Project Technologies Research Centre,
Shanghai, China
Session C Electrical Power Systems
ID: 5029 CP-1
Design of Photovoltaic Fan Drive Based on MPPT
Yuping Zhang, Yuhua Wei, Zhongxiao Yang, Tao Liu, Yi Mou, Dong Chen
Pattern recognition and intelligent control laboratory University of Electronic Science and
Technology of China
53
ID: 5038 CP-2
Two-Three Combined Vectors Direct Power Control Algorithm based Three-Phase Pulse Width
Modulation Rectifier
Wei Xu, Likun Liu
School of Electrical and Electronic Engineering, Huazhong University of Science and Technology
ID: 5056 CP-3
New Damping Model and Control for Low Frequency Oscillation by Interaction between TCSC
and PSS
1
Wei Xu, 1Anqing Chen, 2Chaoxu Mu
1
State Key Laboratory of Advanced Electromagnetic Engineering and Technology, School of
Electrical and Electronic Engineering, Huazhong University of Science and Technology
2
School of Electrical and Automation Engineering, Tianjin University
ID: 5069 CP-4
Novel Negative Sequence Current Detection and Control Strategy for H-Bridge Three-Level Active
Power Filter
1
Wei Xu, 1Renjun Dian, 2Chaoxu Mu
1
School of Electrical and Electronic Engineering, Huazhong University of Science and Technology
2
School of Electrical and Automation Engineering, Tianjin University
ID: 5094 CP-5
Design and Operation of Cryogenic System for 35kV/2000A HTS Power Cables
Tao Tang , Xi Hua Zong, Zhi Guang Yu, Xiao Hong Lu, Yun Wu Han
Superconducting Project Techonlogies Research Centre, Shanghai Electric Cable Research Institute
ID: 5098 CP-6
Research on the Improvement of the Quickness and its Simulation for Magnetic-valve
Controllable Reactor
Pengtai Shi, Mingxing Tian
School of Automation and Electrical Engineering, Lanzhou Jiaotong University
ID: 5101 CP-7
Research on Radial Stability of Large Transformer Windings under Multiple Short-circuit
Conditions
Zhang Bo, Li Yan
Research Institution of Special Electrical Machines, Shenyang University of Technology
ID: 5102 CP-8
Dispatch Analysis of Power System with Energy Storage System When Wind Power Added
Zuoxia Xing, Ning Yan
School of Electrical Engineering, Shenyang University of Technology
ID: 5118 CP-9
Determination of the Number of Turns and Voltage of Control Winding of Controllable Reactor of
Transformer Type
Mingxing Tian, Yina Guo
School of Automation and Electrical Engineering, Lanzhou Jiaotong University
ID: 5120 CP-10
Risk Assessment of Power Systems Integrated with Wind Farm and SMES
Zhen Chen, Xian Yong Xiao, Chang Song Li
College of Electrical Engineering and Information Technology, Sichuan University
ID: 5135 CP-11
Computing the Radar Cross Section of Electromagnetic Scattering from Wind Turbine
Rui Sun, Bo Tang, Ye Li, Zou Fang
China Three Gorges University
ID: 5137 CP-12
Application of Generalized Resonance Theory in Reradiation Interference from UHV Power Lines
Haotian Jiang, Bo Tang, Hongying Cao, Youxian Peng, Ren Liu
54
China Three Gorges University
ID: 5138 CP-13
Dynamic Performance Analysis of SMES for Sensitive Load Voltage Sag Compensation
Zixuan Zheng, Xian-yong Xiao, Yang Liu, Changsong Li
College of Electrical Engineering & Information Technology, Sichuan University
ID: ID: 5157 CP-14
Effect of Backfill Soil Impurity on Electric Field Characteristics of HVDC Grounding-electrode
Tao Zhang, Xiaorui Tan, Yaqin Liu
College of Electrical Engineering and New Energy, China Three Gorges University
ID: 5162 CP-15
Analysis of Restrike Overvoltage of Circuit Breakers in Wind Farms
1
Qibin Zhou, 2Yu Cheng, 2Xiaoyan Bian, 2Feifan Liu
1
Shanghai Lightning Protection Center
2
Shanghai University of Electric Power
ID: 5168 CP-16
Application of SFCL to Improve the Transient Voltage Stability of Grid-Connected Wind Farm
With DFIG During Grid Faults
1
Ran Ou, 1Xianyong Xiao, 1Zhice Zou, 1Changsong Li, 2Danyue Wu
1
College of Electrical Engineering and Information Technology, Sichuan University
2
State Grid Fujian Electric Power Research Institute, State Grid Corporation of China
ID: 5176 CP-17
Investigation on Phase Angle Mismatch of Seires Connected Air-Core Pulsed Alternators
Xiyuan Li
Department of Electrical Engineering, Harbin Institute of Technology
ID: 5202 CP-18
A Linear Magnetic-Geared Wave Energy Generator Ningjun Feng, Haitao
Ningjun Feng, Haitao Yu, Minqiang Hu,Lei Huang, Zhenchuan Shi, Weibo Zhong
School of Electrical Engineering, Southeast University
ID: 5210 CP-19
Study on the Self-Excitation Condition of a Two-Phase Air-Core Pulsed Alternator
Xiyuan Li
Department of Electrical Engineering, Harbin Institute of Technology
ID: 5227 CP-20
The Research on Derivational Topologies and Control of Switched-Capacitor Converter
1
Hai Shi Zhang, 2Xiao Yuan Chen
1
Department of Electrical Engineering, Southwest Jiaotong University
2
Sichuan Normal University
ID: 5241 CP-21
Analysis of Energy Storage Technology in Microgrid
1
Xianxu Huo, 1Guodong Li, 1Dong Zhang, 2Shaoyun Ge
1
Electric Power Research institute of State Grid Tianjin Electric Power Corporation
2
Key Laboratory of Smart Grid Ministry of Education, Tianjin University
ID: 5243 CP-22
Energy Efficiency Diagnosis of Smart Grid Park Based on Multi-level Energy Transfer Model
1
Xianxu Huo, 1Xudong Wang, 1Xiaohui Zhu, 2Shaoyun Ge
1
Electric Power Research institute of State Grid Tianjin Electric Power Corporation
2
Key Laboratory of Smart Grid, Ministry of Education, Tianjin University
ID: 5253 CP-23
Study on Engineering Design and Simulation method of Phase-shifting Reactor
Dongsheng Yuan, Shuhong Wang, Hailin Li, Haijun Zhang, Xi Tao
State Key Laboratory of Electrical Insulation and Power Equipment, Faculty of Electrical Engineering,
Xi’an Jiaotong University
55
ID: 5257 CP-24
Commutation Impacts on Energy Reclaim Control of an Air-Core Pulsed Alternator
Xiyuan Li
Department of Electrical Engineering Harbin Institute of Technology
ID: 5263 CP-25
Adaptive Frequency Regulation Strategy based Integral Sliding Mode Control for Smart Grid with
Renewable Energy Sources
1
Chaoxu Mu, 2Wei Xu, 1Jianxun Jin
1
School of Electrical and Automation Engineering, Tianjin University
2
School of Electrical and Electronic Engineering, Huazhong University of Science and Technology
ID: 5265 CP-26
Neural Network Composite Control for Frequency Stability with Inversion Compesation
1
Chaoxu Mu, 2Wei Xu, 1Jianxun Jin
1
School of Electrical and Automation Engineering, Tianjin University
2
School of Electrical and Electronic Engineering, Huazhong University of Science and Technology
ID: 5267 CP-27
Double-loop SVPWM Control Strategy for multi-level inverter based on LC Filter
Chengtian Wu, Luyang Wang
Shanghai University of Electric Power
ID: 5287 CP-28
Research on a New Method to Measure Unbalance of Multiple-circuit Transmission Lines on the
Same Tower Considering the Impact of Ground Wire
Yufei Wang, Xu Xing, Xue Hua,Sun Lu
School of Electrical Engineering, Shanghai University of Electric Power
ID: 5338 CP-29
Study on Transient Overvoltages Switching Small Inductive Load in the Transformer Circuit with
VCBs
Guangqing Zhang
College of Electrical Engineering, Shanghai University of Electric Power
ID: 5357 CP-30
Investigation on Power and Loss Densities of Scaled-down Laminated Cores
1
Fuxin Fang, 1Haiyang Kong, 1Weimin Guan, 2Yanhui Gao, 2Kazuhiro Muramatsu
1
School of Electrical Engineering Wuhan University
2
Department of Electrical and Electronic Engineering Saga University, Saga, Japan
ID: 5362 CP-31
Studies on the Influences of SFCL on the Transient Recovery Voltage of Circuit Breaker
Bin Li, Yizhe Ou
Key Laboratory of Smart Grid, Ministry of Education, Tianjin University
ID: 5363 CP-32
Studies on the Effect of SFCL on the Transient Stability of Power System
Bin Li, Yizhe Ou
Key Laboratory of Smart Grid, Ministry of Education, Tianjin University
ID: 5370 CP-33
Study on the Axial Vibration of Power Transformer Windings
1
Wenhua Lu, 1Chao Fang, 1Qianwen Zhou, 2Mingmin Wang, 3Fan Zhang, 3Yanjie Cui, 4Yeye Zhu
1
State Grid Electric Power Research Institute Wuhan, China
2
State Grid Jiangsu Electric Company Nanjing China
3
State Key Laboratory of Electrical Insulation and Power Equipment, Xi'an Jiaotong University, Xi’an,
China
4
Suzhou Electric Power Company
ID: 5374 CP-34
An Improved active islanding detection method applying to multi-inverter power system
56
Yuhua Cheng, Kai Chen, Chun Yin, Jie Zhang, Libing Bai
School of Automation Engineering, University of Electronic Science and Technology of China
ID: 5375 CP-35
Grid-Connected Photovoltaic System Using Compound Current Control of The Novel Repetitive
and PI
Jie Zhang, Yuhua Cheng, Chun Yin, Kai Chen, Libing Bai
School of Automation Engineering, University of Electronic Science and Technology of China
Session D Electrical Machines
ID: 5025 DP-1
Analyzing and Calculating of the Cogging Torque of Halbach Array Permanent Magnet Motor
1
Lin Liu, 1Libing Jing
1
College of Electrical Engineering and New Energy, China Three Gorges University
2
Hubei Collaborative Innovation Centre for Micro-grid of New Energy
ID: 5028 DP-2
Exact Analytical Method for Air-Gap Main Magnetic Field Computation and Cogging Torque of
Surface-Mounted Permanent-Magnet Motors
Libing Jing, Qixing Gao,Lin Liu
College of Electrical Engineering & New Energy, China Three Gorges University
ID: 5037 DP-3
Novel Synchronous Machine with Permanent Magnet in Stator Yoke
Wei Xu, Mingjie He
School of Electrical and Electronic Engineering, Huazhong University of Science and Technology
ID: 5039 DP-4
Novel Efficiency Optimization Control Algorithm for Single-sided Linear Induction Motor
Wei Xu, Dong Hu
State Key Laboratory of Advanced Electromagnetic Engineering and Technology, School of
Electrical and Electronic Engineering, Huazhong University of Science and Technology
ID: 5040 DP-5
New Approach for Thrust Ripple Reduction on Permanent Magnet Flux-Switching Linear Motor
1
Wei Xu, 2Chaoxu Mu
1
State Key Laboratory of Advanced Electromagnetic Engineering and Technology, School of
Electrical and Electronic Engineering, Huazhong University of Science and Technology
2
School of Electrical and Automation Engineering, Tianjin University
ID: 5055 DP-6
Study on Deformations of the two-stage Impellers of Contra-Rotating Fan driven by
pole-changing motors
Dawei Meng, Yunyan Xia, Zeqi Zhang
College of Electrical and Electronic Engineering, Harbin University of Science and Technology
ID: 5068 DP-7
Conducted Common-mode Equivalent Circuit of Induction Motor for EMI Analysis
Xiao Fang, Ge Baojun, Ning Zhaoyang, Wang Zhe
College of Electrical and Electronic Engineering, Harbin University of Science and Technology
ID: 5085 DP-8
Coupling Characteristics Research on the Subsections of Submersible Motor
Yongming Xu, Mengmeng Ai, Zhiguo Jiang
Electrical and Electronic Engineering College, Harbin University of Science and Technology
ID: 5090 DP-9
Improvement in Dynamic Stability of Self-Excited Induction Generator with Short-Shunt
Capacitors
57
Xinzhen Wu, Yang Zhang, Kai Wang
Department of Electrical Engineering, Qingdao University
ID: 5091 DP-10
Steady-State Analysis of Islanded Three-phase Induction Generator in Single-phase Operation
with Combined Equivalent Circuit
Xinzhen Wu, Yang Zhang
Department of Electrical Engineering, Qingdao University
ID: 5100 DP-11
Normal Force and Vibration Investigation of Linear Permanent-Magnet Vernier Machine
Yanxin Mao, Guohai Liu, Wenxiang Zhao, Jinghua Ji
School of Electrical and Information Engineering, Jiangsu University
ID: 5105 DP-12
Hybrid Stepping Motor with Permanent Magnets in Stator-Presentation, Parameter Calculation
and Design
Binglin Lu, Yanliang Xu
School of Electrical Engineering, Shandong University
ID: 5110 DP-13
Armature Reaction of A New Four-phase Doubly Salient Electro-magnetic Generator
Liwei Shi, Bo Zhou
School of Automation, Nanjing University of Aeronautics and Astronautics
ID: 5119 DP-14
Analysis of the Eddy Current Loss in the Secondary of Tubular Flux-switching Permanent Magnet
Linear Motor (TFSPMLM)
Qiang Tan, Xuzhen Huang, Bo Zhou, Liu Yang
Nanjing University of Aeronautics and Astronautics
ID: 5127 DP-15
A Novel Transverse-Flux PM Linear Machine with Double Ω-hoop Stator
Zhou Jia, Weifeng Chen, Qingshan Liu, Li Yu, Hongyun Jia
School of Information and Control, Nanjing University of Information Science and Technology
ID: 5131 DP-16
Pole Ratio Effect on Performances of Linear Permanent Magnet Vernier Motor
Shiyuan Wang, Wenxiang Zhao, Jinghua Ji
School of Electrical and Information Engineering, Jiangsu University
ID: 5141 DP-17
Inductance Identification of Permanent Magnet Synchronous Machine at Standstill
Guangqiang Lu, Yaocheng Yan, Junjie Ni
Department of Automation, Nanjing University of Science & Technology
ID: 5144 DP-18
Characteristics Analysis of PM Linear Synchronous Motor with Non-uniform Air-gap
Xiaozhuo Xu, Haichao Feng, Xudong Wang, Baoyu Du
School of Electrical Engineering and Automation, Henan Polytechnic University
ID: 5160 DP-19
Analysis and Minimization of Cogging Force in Tubular Transverse Flux Linear Machines for Direct
Drive Applications
Qian Wang, Jibin Zou, Yongxiang Xu, Yong Li
Dept. of Electrical Engineering, Harbin Institute of Technology
ID: 5161 DP-20
Design and Analysis of High Speed Outer Rotor Permanent Magnet Claw Pole Machine
Guangwei Liu, Gengwu Li, Fengge Zhang
School of Electrical Engineering, Shenyang University of Technology
ID: 5177 DP-21
58
Comparison of Doubly Salient Permanent Magnet Machines with E-shaped and Π-shaped Stator
Iron Core Segments
1
Yi Du, 1Yandong Sun, 1Xiaoyong Zhu, 1Feng Xiao, 1Yuxin Sun, 1Huangqiu Zhu, 2Ming Cheng
1
School of Electrical and Information Engineering, Jiangsu University
2
School of Electrical Engineering, Southeast University
ID: 5183 DP-22
Core Loss Analysis of Transverse Flux Tubular Motor in Variable-Speed Reciprocating Periodic
Motion Mode
1,2
Mei Zhao, 1Hongyong Yang, 1Huixia Liu, 1S.N.Zhang, 2Kai Liu, 2Jibin Zou
1
Department of Information and Electrical Engineering Ludong University
2
Department of Electrical Engineering and Automation Harbin Institute of Technology
ID: 5222 DP-23
Influence for Electromagnetic Properties and Iron Loss of Induction Motors under Rotor
Eccentricity Fault
Shuye Ding, Shan Jiang, Mengqi Wang, Tianyu Guan, Guanghui Cui
College of Electrical and Electronic Engineering, Harbin University of Science and Technology
ID: 5225 DP-24
Analysis and Performance Evaluation of a Novel High Reliability Linear Switch Reluctance
Machine for Low Cost Conveyor Applications
Daohan Wang, Xiuhe Wang, Chenghui Zhang
Shandong University
ID: 5228 DP-25
Prediction of the Overall Characteristics for High Power Permanent Magnet Synchronous Motor
with Multi Phase Units
1,2
Xintong Jiang, 1Weikai Li, 2Yong Li, 1Yu Tian
1
College of Information Technology, Heilongjiang Bayi Agricultural University
2
College of Electric Engineering, Harbin Institute of Technology
ID: 5230 DP-26
Analysis and Experimental Study of Brushless Electrically-Excited Synchronous Generator with
Hybrid Rotor
Fengge Zhang，Guanglong Jia, Yang Zheng, Tao Guan
Shenyang University of Technology
ID: 5319 DP-27
A New Halbach Arc Permanent Magnet Synchronous Motor With Three-Dimensions Air Gap Used
on Large Telescope
Haitao Wang, Shuhua Fang, Baocheng Guo
School of Electrical Engineering, Southeast University
ID: 5333 DP-28
Modeling and Flux Leakage Analysis for Long-stator PM Linear Motor Including Longitudinal End
Effects
1
Mingna Ma, 2Liyi Li
1
School of Electrical Engineering and Automation, Hefei University of Technology
2
Department of Electrical Engineering, Harbin Institute of Technology
ID: 5335 DP-29
A Hybrid-Excited Flux-Controllable Brushless Motor for Electric Vehicle
Yulong Liu, Shuangxia Niu, W. N. Fu
Department of Electrical Engineering, The Hong Kong Polytechnic University, Hong Kong, China
ID: 5343 DP-30
Design and Analysis of a Novel Flux-modulated Permanent Magnet Linear Generator with
Sandwiched Armature Stator
1
Mingna Ma, 2Liyi Li
59
1
School of Electrical Engineering and Automation, Hefei University of Technology
Department of Electrical Engineering, Harbin Institute of Technology
ID: 5358 DP-31
Modeling and Finite Element Analysis of Suspension Force for a Bearingless Permanent Magnet
Synchronous Motor
1
Xiaodong Sun, 1Shuai Luo, 1Long Chen, 1Zebin Yang, 1Jianfeng Chen, 2Jianguo Zhu, 2Youguang Guo
1
Automotive Engineering Research Institute Jiangsu University
2
School of Electrical, Mechanical and Mechatronic Systems University of Technology, Sydney,
Australia
ID: 5380 DP-32
Calculation and Analysis of IGBT Power Loss in Drive System for EV
Huihui Bao, Wei Zhang, Yi Yang, Yi Chen
Department of Electrical Engineering, Nantong University
2
Session E Magnets
ID: 5057 EP-1
Multi-layer Windings Effect on Performance of Flux-Switching Permanent Magnet Machines
1
Wei Xu, 1Ziyue Wang, 2Gang Lei, 2Jiangguo Zhu
1
School of Electrical and Electronic Engineering, Huazhong University of Science and Technology
2
School of Electrical, Mechanical, and Mechatronic Systems, University of Technology, Sydney,
NSW, Australia
ID: 5070 EP-2
IBEM Applied to the Design of Open Bipanar Shim Coils for Superconducting MRI System
Yang Hu, Qiuliang Wang, Xinning Hu, Luguang Yan
Key Laboratory of Applied Superconductivity, Institute of Electrical Engineering, Chinese Academy
of Sciences
ID: 5122 EP-3
Dynamic Simulation of a Small Scale Superconducting Augmented Railgun
Sizhuang Liang, Youtong Fang, Xiaoyan Huang
College of Electrical Engineering, Zhejiang University
ID: 5200 EP-4
A Coreless Synchronous Linear Machine with Superconducting Excitation Winding for
Electromagnetic Catapult
Lei Huang, Haitao Yu, Hao Chen
School of Electrical Engineering, Southeast University
ID: 5217 EP-5
Analysis and Design Optimization of Tubular Linear Magnetic Gear
Ningjun Feng, Haitao Yu, Minqiang Hu, Lei Huang, Zhenchuan Shi, Weibo Zhong
School of Electrical Engineering, Southeast University
ID: 5221 EP-6
Analysis of Magnetic Field and Electromagnetic Force about Outlet Terminal of Air-core Reactor
Cheng Zhang, Xiaohua Bao, Yunpeng Hu, Yuanyang Chen
College of the Electrical Engineering and Automation, Hefei University of Technology
ID: 5233 EP-7
A Novel Permanent Magnet Biased Heteropolar Radial Magnetic Bearing with Low Displacement
Stiffness
1
Leitao Wu, 1Dong Wang, 2Kang Wang, 1Zhenzhong Su, 1Xianbiao Zhang
1
National Key Laboratory of Science and Technology on Vessel IPS, Naval University of Engineering
2
Engineering Research Center for Motion Control of Ministry of Education, Southeast University
ID: 5235 EP-8
60
Detent Force Minimization of a Novel Linear-rotary Permanent Magnet Actuator with
Independent Magnetic Circuit Structure
Kaikai Guo, Shuhua Fang, Heyun Lin, Yang Zhang, Hui Yang
School of Electrical Engineering, Southeast University
ID: 5236 EP-9
Quantities Comparative Analysis of a Linear-rotary Permanent Magnet Actuator with HTS Field
Winding
Shuhua Fang, Kaikai Guo, Heyun Lin, Dong Wang, Hui Yang
School of Electrical Engineering, Southeast University
ID: 5276 EP-10
Design of Superconducting Shim Coils for an Open Bipanar MRI System Using IBEM
1
Yang Hu, 1Xinning Hu, 2Youtong Fang, 1Luguang Yan
1
Institute of Electrical Engineering, Chinese Academy of Sciences
2
College of Electrical Engineering, Zhejiang University
ID: 5279 EP-11
Analysis of Electromagnetic Properties of Superconducting Suspension System for Gravity
Measurement
Jingwen Xu, Xinning Hu, Hui Wang, Chenchen Gou, Jianbo Zhou, Hao Wang
Key Laboratory of Applied Superconductivity, Institute of Electrical Engineering Chinese Academy
of Sciences, University of the Chinese Academy of Science
ID: 5280 EP-12
Flow Control of Magnetohydrodynamic Flow in a Cylindrical Spiral Channel
Kai Yan, Yinming Dai
Institute of Electrical Engineering, Chinese Academy of Sciences
ID: 5282 EP-13
Shape Optimization of Ferromagnetic Pole of a Superconducting MRI Magnet with Niching
Genetic Algorithm
Yi Li, Yinming Dai, Hui Wang
Key Laboratory of Applied Superconductivity, Institute of Electrical Engineering, Chinese Academy
of Sciences
ID: 5283 EP-14
Design and Test of a Five-section Linear Induction Coil Launcher
1
Xian Li, 1Housheng Wang, 1Shunzhong Chen, 1Jianhua Liu， 2Youtong Fang
1
Institute of Electrical Engineering, Chinese Academy of Sciences
2
College of Electrical Engineering, Zhejiang University
ID: 5285 EP-15
Simulation and Experimental Study on Between YBCO Double Pancake Coils of High Fieldlap Joint
Insert Magnets
1
Chenchen Gou, 1Jianhua Liu, 1Housheng Wang, 2Youtong Fang, 1Jingwen Xu, 1Jianbo Zhou, 1Hao
Wang
1
Institute of Electrical Engineering, Chinese Academy of Sciences,
2
College of Electrical Engineering Zhejiang University
ID: 5286 EP-16
Design and test of displacement transducer for an Electrode-insulated Electrostatically
Suspended Gyroscope
1
Jianhua Liu, 1Hui Wang, 1Kun Chang, 1Xian Li, 2Youtong Fang
1
Institute of Electrical Engineering, Chinese Academy of Sciences,
2
College of Electrical Engineering, Zhejiang University
ID: 5289 EP-17
Preparation and Magnetic Properties of Nickel Nanowires by Magnetic Field-induction
1
Wanshuo Sun, 2Ying Liu, 1Junsheng Cheng, 1Lankai Li, 1Yinming Dai
61
1
Institute of Electrical Engineering, Chinese Academy of Science
School of Material Science and Engineering, Beijing Institute of Technology
ID: 5290 EP-18
Fabrication of Superconducting Joint by Electromagnetic Forming Method
1
Junsheng Cheng, 1Feng Zhou, 1Lankai Li, 1Chunyan Cui, 1Wanshuo Sun, 2Youtong Fang, 1Yinming
Dai
1
Institute of Electrical Engineering, Chinese Academy of Sciences,
2
College of Electrical Engineering, Zhejiang University
ID: 5296 EP-19
Discrete Frequency Control for Soft Starter with Reduced Starting Current
1
Hongming Hu, 1Zhiwen Xu, 2Wei Xu
1
School of Automation, Wuhan University of Technology
2
School of Electrical and Electronic Engineering, Huazhong University of Science and Technology
ID: 5297 EP-20
Model Predictive Direct Torque Control of Permanent Magnet Synchronous Machine with
Reduced Torque Ripple
1
Hongming Hu, 1Peng Han, 1Xuejiao Liu, 2Wei Xu
2
1
School of Automation, Wuhan University of Technology
School of Electrical and Electronic Engineering, Huazhong University of Science and Technology
ID: 5310 EP-21
Optimal Design of Permanent-Magnet Machines Using RSM Based Aploex Method
Xiaoyu Liu,W. N. Fu
Department of Electrical Engineering, the Hong Kong Polytechnic University
ID: 5312 EP-22
Design Aspects and Optimization of a High Thrust Density Dual Stator Yokeless Linear Switched
Reluctance Machine for Harsh Conditions
1
Daohan Wang, 1Xiuhe Wang, 2Chenghui Zhang
1
School of Electrical Engineering, Shandong University,
2
School of Control Science and Engineering, Shandong University
ID: 5315 EP-23
Numerical Computation Analysis of a Novel Magnetic Field Modulated Gear Rack
Xinghe Fu, Biao Wang, Kai Liu, Mingyao Lin
School of Electrical Engineering, Southeast University
ID: 5321 EP-24
Comparative Study of Novel Designs of Triple-Permanent-Magnet-Excited Magnetic Gears
Yuan Mao, Shuangxia Niu, W. N. Fu
The Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong
ID: 5346 EP-25
Analysis and Modeling of a Novel Brushless Exciter Based on a Topology of Hybrid Excitation
Zhenzhong Su, Dong Wang, Yunjun Guo, Xinqiang Yi, Youxing Xiong
National Key Laboratory of Science and Technology on Vessel Integrated Power System, Naval
University of Engineering
ID: 5350 EP-26
A Novel 3D Magnetic Field Generator with Larger Uniform Region
1
Junquan Chen, 1Dong Wang, 2Yonghong Zhu, 1Yongxing Xiong, 1Siwei Cheng, 3Zhishu Yu
1
National Key Laboratory of Science and Technology on Vessel Integrated Power System, Naval
University of Engineering
2
Human Forever Elegance Technology Co., Ltd
3
Zhejiang Province Institute of Metrology
2
62
Session F Electronics
ID: 5030 FP-1
Research on Energy Management System of Electric Vehicle Based on Aluminum Air Fuel Cell
Yuping Zhang, Yi Mou, Zhongxiao Yang, Yuhua Wei, Tao Liu, Dong Chen
Pattern recognition and intelligent control laboratory, University of Electronic Science and
Technology of China
ID: 5034 FP-2
A Comparative Study of Compressed Sensing Approaches with Splitting Bregman Framework for
Radial UTE MRI
Dongjie Bi, Yongle Xie, Lan Ma, Xuan Xie, Pan Niu
School of Automation Engineering, University of Electronic Science and Technology of China
ID: 5044 FP-3
A Study on the Effect of object’s shape in the Underwater Active Electrolocation
Lu Liu, Jiegang Peng
School of Automation Engineering and Center for Robotics, University of Electronic Science and
Technology of China
ID: 5115 FP-4
Observation of Nonlinearity in Dual-Band Superconducting Filter Using Spirally Asymmetric
Stepped-Impedance Resonators
Haiwen Liu, Fan Liu, Feng Qin, Baoping Ren, Pin Wen, Xuehui Guan, Yang Peng, Jianwei Liu
School of Information Engineering, East China Jiaotong University
ID: 5116 FP-5
Compact Triple-Band High-Temperature Superconducting Filter Using Coupled-Line Stepped
Impedance Resonator(C-SIR)
Haiwen Liu, Yang Peng, Xuehui Guan, Jiuhuai Lei, Baoping Ren, Feng Qin, Pin Wen
East China of Jiaotong University
ID: 5117 FP-6
Design of Dual-Band Superconducting Bandpass Filter Using Dual-Mode Hairpin Ring Resonator
Baoping Ren, Haiwen Liu, Xuehui Guan, Fan Liu
School of Information Engineering, East China Jiaotong University
ID: 5163 FP-7
Comparative Investigation of Interior Permanent Magnet Machines for Hybrid Electric Vehicles
Junqiang Zheng, Wenxiang Zhao, Jinghua Ji, Guohai Liu
School of Electrical and Information Engineering, Jiangsu University
ID: 5171 FP-8
Development of a Permanent Magnet Slotless Limited-Angle Torque Motor with a Moving Coil
for Optical Scanning System
Jibin Zou, Guodong Yu, Yongxiang Xu, Qian Wang, Yanyu Wei, Junlong Li
Department of Electrical Engineering, Harbin Institute of Technology
ID: 5179 FP-9
Novel Composite Sliding Mode Control for PMSM System Based on Disturbance Observer
1
Wei Xu, 1Yajie Jiang, 2Chaoxu Mu
1
School of Electrical and Electronic Engineering, Huazhong University of Science and Technology
2
School of Electrical and Automation Engineering, Tianjin University
ID: 5182 FP-10
A Discontinuous Coordinated Charging Strategy for Electric Vehicle
1
Yong Yang, 1Zhizhen Liu, 2Dongming Qu, 1Guozheng Qi
1
School of Electrical Engineering, Shandong University
2
Qingdao Tgood Electric Co.,Ltd
63
ID: 5189 FP-11
Static Characteristics of a Double Stator Linear Rotary Permanent Magnet Actuator
Lei Xu, Mingyao Lin, Xinghe Fu, Nan Li
School of Electrical Engineering, Southeast University
ID: 5193 FP-12
IGBT Power Loss Analysis and Calculation of Drive System for EV
Huihui Bao, Wei Zhang, Yi Yang, Yi Chen
School of Electrical Engineering, Nantong University
ID: 5194 FP-13
Calculation and Analysis of IGBT Power Loss in Drive System for EV
Huihui Bao, Wei Zhang, Yi Yang, Yi Chen
School of Electrical Engineering, Nantong University
ID: 5231 FP-14
Design and Analysis of a Novel Axial Field Flux-Switching Memory Machine Suitable for Variable
Speed Operation
Nian Li, Mingyao Lin, Da Xu, Lei Xu, Wei Zhang
School of Electrical Engineering, Southeast University
ID: 5332 FP-15
Design of Quad-Channel Superconducting Diplexer With Dual-Mode T-shaped Spiral Resonators
Haiwen Liu, Shuangshuang Zhu, Pin Wen, Xuehui Guan
RF communications and sensor networks, East China Jiaotong University
ID: 5336 FP-16
Design and Sensorless Control of a Novel Axial Flux Permanent Magnet Machine for In-Wheel
Applications
1
Xiang Luo, 2Shuangxia Niu
1
School of Naval Architecture, Ocean & Civil Engineering, Shanghai Jiao Tong University
2
Department of Electrical Engineering, The Hong Kong Polytechnic University, Hongkong, China
ID: 5337 FP-17
Measurements of Temperature Dependent Performance of a Micro strip Filter using NBCO Film
Jiabin Chen, Bin Wei, Bisong Cao, Xubo Guo, Linan Jiang, Chenjie Luo
The State Key Laboratory of Low-Dimensional Quantum Physics, Department of Physics, Tsinghua
University
ID: 5347 FP-18
An Efficient and Polarization Sensitive SNSPD with Coupled Asymmetric SRR-loaded Cavity
Mengmeng Yang, Fan Zheng, Guanghao Zhu, Biaobing Jin
Research Institute of Superconductive Electronics, Nanjing University
ID: 5355 FP-19
Determination of Level Populations in Superconducting Phase Qutrits
H. K. Xu, W. Y. Liu, F. F. Su, Ye Tian, S. P. Zhao
Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of
Sciences
Session G Cryogenics and Thermal/Electrical Insulation
ID: 5066 GP-1
Analysis of Heat Transfer Based on Fluid Network Decoupling in Submersible Motor
Yongming Xu, Fei Liu
College of Electrical and Electronic Engineering, Harbin University of Science and Technology
ID: 5076 GP-2
Characterization of Partial Discharge with Fluorinated Polyimide Films in High Temperature
Superconducting Cable Insulation
1
Jie Li, 1X. G. Wang, 2Y. Q. Xing, 2B. X. Du
64
1
State Grid Shandong Electric Power Research Institute
School of Electrical Engineering and Automation
Tianjin University
ID: 5146 GP-3
Performance of PCL under Different Cooling Modes
Guixin Chen, Yinshun Wang, Wei Pi, Chenjie Shi, Tingting Li, Jiawei Li
North China Electric Power University
ID: 5153 GP-4
Reducing Noise for A Superconducting Amorphous Metal Core Transformer By Using
Micro-perforated Panel Absorber
1
D. S. Liu, 2B. X. Du, 2J. G. Zhang
1
School of Electrical Engineering & Automation, Jiangxi University of Science and Technology
2
Key Laboratory of Smart Grid of Education Ministry, School of Electrical Engineering and
Automation, Tianjin University
ID: 5159 GP-5
Study on Initial Slope Characteristic Quantity of Return Voltage
Tao Zhang, Xiaorui Tan, Bin Zhang
College of Electrical Engineering and New Energy, China Three Gorges University
ID: 5190 GP-6
Surface Flashover Characteristics of Fluorinated Polyimide Films in Liquid Nitrogen
1
B. X. Du, 1Y. Q. Xing, 1J. X. Jin，1P. H. Huang，2J. Li
1
School of Electrical Engineering and Automation, Tianjin University
2
State Grid Shandong Electric Power Research Institute
ID: 5206 GP-7
Effect of Magnetic Field on Tree Characteristics in Silicone Rubber
1
T. Han, 1B. X. Du, 1J. Li, 2Z. L. Ma, 2Y. G. Guo
1
School of Electrical Engineering and Automation, Tianjin University
2
Dalian Electrical Power authority
ID: 5211 GP-8
Effect of Liquid Nitrogen on Surface Charge of Polypropylene Film under DC and Pulse Voltages
B. X. Du, P. H. Huang, Y. Q. Xing, J. X. Jin
School of Electrical Engineering and Automation, Tianjin University
ID: 5213 GP-9
Effect of Magnetic Field on Electrical Treeing Behavior in Silicone Rubber under Low Temperature
B. X. Du, Y. Yu, T Han, J. G. Su, B. Cui
School of Electrical Engineering and Automation, Tianjin University
ID: 5239 GP-10
Effect of Low Temperature on Tracking Failure Process of Epoxy/BN Composite
1
M. Xiao, 1J. W. Zhang, 2B. X. Du, 2Y. Q. Xing
1
Jinan Power-supply Company
2
School of Electrical Engineering and Automation, Tianjin University
ID: 5348 GP-11
Effect of External Magnetic Fields on the Breakdown and Partial Discharge Characteristics of
Vegetable Oil
B. X. Du, X. L. Li, Y. Q. Xing, J. Li, J. P. Jiang
Key Laboratory of Smart Grid of Education Ministry, School of Electrical Engineering and
Automation, Tianjin University
ID: 5369 GP-12
Developing Process of Partial Discharge in Oil-Paper Insulation Under Needle-Plate Defects
1
Yanjie Cui, 1Lingyu Zhu, 1Shengchang Ji, 2Xiaobo Ou, 2Dan Zhou, 2Chunyao Lin
2
65
1
State Key Laboratory of Electrical Insulation and Power, Xi’an Jiaotong University, Xi’an
High Voltage Technology Research Department Guangdong Electric Power Research Institute
Guangzhou
2
Session H3 Modeling, Analysis and Design
ID: 5027 HP-1
Design of Remote Control Plug
Yuping Zhang, Tao Liu, Zhongxiao Yang, Yi Mou, Yuhua Wei, Dong Chen
Pattern recognition and intelligent control laboratory, University of Electronic Science and
Technology of China
ID: 5033 HP-2
The Early Kick Monitoring Based on the Ultrasonic Measurement Techniques in Deep Drilling
Shengnan Li, Hui Zhao
School of Automation Engineering, University of Electronic Science and Technology
ID: 5042 HP-3
The Design and Implementation of TCP Hardwiring and Offloading Engine
1
Shuyan Jiang, 1Zhi Lu, 1Yuanyuan Mao, 2Gang Luo, 2Qi Li
1
School of Automation Engineering, University of Electronic Science and Technology of China
2
Chengdu Technological University
ID: 5046 HP-4
New Strategy Combining Fuzzy Logic and Sliding Mode Control for Speed Regulation of PMSM
1
Chaoxu Mu, 2Wei Xu
1
School of Electrical and Automation Engineering, Tianjin University
2
School of Electrical and Electronic Engineering, Huazhong University of Science and Technology
ID: 5047 HP-5
Investigation of the Electro-Thermal Sub-Strong Coupling Model Based on Temperature
Character
Yujiao Zhang, Gangliang Wu
College of Electrical Engineering and New Energy, China Three Gorges University, Yichang
ID: 5054 HP-6
Airflow Pressure Pulsation of Contra-rotating Fan and its Influence on the Motor
Yunyan Xia, Dawei Meng, Qian Wang
College of Electrical and Electronic Engineering, Harbin University of Science and Technology
ID: 5061 HP-7
Simulation Analysis of Transformer Inrush Current Based on the same Switching Angle
Guozheng Qi, Zhizhen Liu, Yong Yang, Weiping Liao, Xiaodong Qu, Kai Xu, Hongxing Chen
School of Electrical Engineering, Shandong University
ID: 5063 HP-8
Equivalent Magnetic Circuit Model of Novel Disk Transverse-flux segment-stator Permanent
Magnet Brushless Machine
1
Yanliang Xu, 2Xiao Gong
1
School of Electrical Engineering, Shandong University
2
Zhongke Shengchuang (Qingdao) Electrical Co., Ltd
ID: 5065 HP-9
Calculation Methodology of Winding Temperature Field in Large Power Transformers based on
Fluid Network
Yongming Xu, Fei Liu
College of Electrical and Electronic Engineering, Harbin University of Science and Technology
ID: 5072 HP-10
Equivalent Parameter Estimation of a Single-sided Linear Induction Motor Based on
Electromagnetic Field Induced by Current FFT-Wave
66
Jun Di, Yu Fan, Yajing Liu
School of Electrical Engineering, Beijing Jiaotong University
ID: 5089 HP-11
Investigation of the Heat Characteristic Based on the Thermal Network Method for High Power
Density Motor
Yongming Xu, Mengmeng Ai, Xue Yang
Electrical and Electronic Engineering College, Harbin University of Science and Technology
ID: 5107 HP-12
Design of Differential Mode Filter for Suppressing Common Mode Voltage of Motor
Xiaojun Liu, Guangming Zhang, Lei Mei, Deming Wang
College of electrical engineering and control science, Nanjing Tech University
ID: 5114 HP-13
Nonlinear Flux Linkage Modeling of a Bearingless Permanent Magnet Synchronous Motor Based
on AW-LSSVM Regression Algorithm
1
Xiaodong Sun, 1Shuai Luo, 1Long Chen, 1Zebin Yang, 1Jianfeng Chen, 2Jianguo Zhu, 2Youguang Guo
1
Automotive Engineering Research Institute, Jiangsu University
2
School of Electrical, Mechanical and Mechatronic Systems, University of Technology, Sydney,
Sydney, Australia
ID: 5139 HP-14
Electromagnetic Scattering Field Calculation of UHV Power Transmission Line at VHF Based on
Fitting Algorithm
Bo Tang, Youxian Peng, Hongying Cao, Rui Sun, Zhuo Wu
China Three Gorges University
ID: 5152 HP-15
Improved Finite-Control-Set Model Predictive Control Algorithm for Disc Coreless Permanent
Magnet Synchronous Motor based ThreeLevel NPC Inverter
1
Xiaoguang Wang, 1Yun Zhao, 1Xinhua Li, 2Wei Xu
1
School of Electrical and Electronic Engineering, Hubei University of Technology
2
School of Electrical Engineering and Automation, Huazhong University of Science and Technology
ID: 5158 HP-16
Parameter Estimation of Dielectric Response Circuit using Improved Mathematical Model
Tao Zhang, Xiaoqin Li, Qian Zou
College of Electrical Engineering and New Energy, China Three Gorges University
ID: 5166 HP-17
Variable-Reluctance Resolver Rotor Design Based on FEA and Matlab Co-Simulation
Wentao Li, Surong Huang
Shanghai University
ID: 5170 HP-18
Harmonic Detection Method based on Positive Sequence Extractor of Fundamental Current
Tao Chen, Lu Yang Wang, He Xing Wang, Shu Juan Yuan, Ning Gao
Electric Power Engineering, Shanghai University of Electric Power
ID: 5212 HP-19
Parameter Calculation of Solid Wires in Transformer Windings
1,2
Xiaojing Liu, 1Youhua Wang, 2Jianguo Zhu, 2Youguang Guo, 1,2Chengcheng Liu
1
Province-Ministry Joint Key Laboratory of Electromagnetic Field and Electrical Apparatus Reliability,
Hebei University of Technology
2
School of Electrical, Mechanical and Mechatronic Systems, University of Technology Sydney, NSW,
Australia
ID: 5223 HP-20
Determination of JA Core Hysteresis Model Parameters Based on Fuzzy- Shuffled Frog Leaping
Algorithm
67
Yang Wang, Zhi Zhen Liu
School of Electrical Engineering Energy, Shandong University
ID: 5250 HP-21
Design and Calculation of Planar Eddy Current Coil in Coin Identification
Naming Zhang, Shuhong Wang
State Key Laboratory of Electrical Insulation and Power Equipment, School of Electrical Engineering,
Xi'an Jiaotong University
ID: 5251 HP-22
Electromagnetic-thermal Simulation of Cold Crucible Considering Surface-to-Surface Heat
Radiation
1
Hailin Li, 1Shuhong Wang, 1Youpeng Huangfu, 1Song Wang, 2Jianguo Zhu
1
State Key Laboratory of Electrical Insulation and Power Equipment, School of Electrical
Engineering, Xi'an Jiaotong University
2
School of Electrical, Mechanical and Mechatronic Systems, University of Technology, Sydney, NSW
2007, Australia
ID: 5255 HP-23
Optimal Design of Rectifier Transformer
Xi Tao, Shuhong Wang, Youpeng Huangfu, Dongsheng Yuan, Song Wang
School of electrical engineering, Xi’an Jiaotong University
ID: 5256 HP-24
Modeling the Stress Dependence of Magnetic Hysteresis Based on Stoner-Wohlfarth Theory
1,2
Weijie Xu, 1Nana Duan, 1Shuhong Wang, 2Youguang Guo, 2Jianguo Zhu
1
State Key Laboratory of Electrical Insulation and Power Equipment, School of Electrical
Engineering, Xi’an Jiaotong University
2
School of Electrical, Mechanical and Mechatronic Systems, University of Technology, Sydney, NSW
2007, Australia
ID: 5268 HP-25
Numerical Analysis of Three-Phase CSR of TCT Type
1
Guang Yang, 1Lin Li, 2Xile Zhang
1
State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources, North
China Electric Power University
2
Baoding Tianwei Baobian Electric Co., Ltd
ID: 5273 HP-26
A 3-D Magnetic Equivalent Circuit of an Axial-Flux MEMS Micromotor
1
Xiaofeng Ding, 1Guanliang Liu, 1Hong Guo, 2Hua Bai
1
School of Automation Science and Electrical Engineering, Beihang University
2
Department of Electrical and Computer Engineering, Kettering University, Flint, MI, USA
ID: 5275 HP-27
Torque Improvement of Variable Speed Multiphase Induction Motor Injecting Third-Order
Harmonic
Huijuan Liu, Jun Wang
School of Electrical Engineering, Beijing Jiaotong University
ID: 5300 HP-28
Design and Analysis of a Linear Slotless Generator with Improved Halbach PM Arrays for Wave
Energy Conversion
1,2
Jing Zhang, 2Haitao Yu, 2Minqiang Hu, 2Lei Huang
1
Department of Electrical Engineering, Jinling Institute of Technology
2
School of Electrical Engineering, Southeast University
ID: 5309 HP-29
Performance Simulation of Flux Modulation Permanent Magnet Machines With Three Topologies
1
HuiJuan Liu, 1Yue Hao, 2ShuangXia Niu, 1JingXiong Zhang
68
1
School of Electrical Engineering, Beijing Jiaotong University
Dept. of Electrical and Electronic Engineering, The Hong Kong Polytechnic University
ID: 5313 HP-30
Performance Analysis of a PM Brushless Roter Claw Pole Motor Using 3D FEM
1
Zhenyang Zhang, 1Huijuan Liu, 1Yue Hao, 2Weinong Fu
1
School of Electrical Engineering, Beijing Jiaotong University
2
Dept. of Electrical and Electronic Engineering, The Hong Kong Polytechnic University
ID: 5323 HP-31
Estimation of Measurement Uncertainty for Devices with Extreme Fisher Information
Xuan Xie, Xifeng Li, Dongjie Bi, Yongle Xie
School of Automation Engineering, University of Electronic Science and Technology of China
ID: 5326 HP-32
A Novel Artificial Bee Colony Algorithm for Brushless DC Wheel Design
Xiu Zhang, Xin Zhang
College of Electronic and Communication Engineering, Tianjin Normal University
ID: 5349 HP-33
2D FEM Transient Analysis of Permanent Magnet Motor Considering Skin Effect of Stator
Winding
1
Junquan Chen, 1Dong Wang, 1Siwei Cheng, 2Zhishu Yu
1
National Key Laboratory of Science and Technology on Vessel Integrated Power System, Naval
University of Engineering
2
Zhejiang Province Institute of Metrology
ID: 5351 HP-34
Theoretical Analysis and Design of an Extremely Low Frequency Magnetic Field Stimulation
System for Tumor suppression
Naming Zhang, Shuhong Wang
State Key Laboratory of Electrical Insulation and Power Equipment, School of Electrical Engineering,
Xi'an Jiaotong University
ID: 5356 HP-35
EMC Prediction Method of High Voltage Multi-Circuit Transmission on the Same Tower Based on
Improved Least Squares Method
Hua Xue, Haixia Li
College of Electrical Engineering Shanghai University of Electric Power Shanghai, CHINA
ID: 5373 HP-36
Stainless Steel Weld Defect Detection Using Eddy Current Pulsed Thermography
1
Yuhua Cheng, 1Libing Bai, 2Fan Yang, 1Yifan Chen, 3Shenhua Jiang, 1Chun Yin
1
School of Automation Engineering, University of Electronic Science and Technology of China,
Chengdu 611731, China
2
NDT, Nuclear Power Institute of China, Chengdu 610041, China
3
CNNP Nuclear Power Operations Management Co. Ltd., Qinshan 314300, China
2
HTS Application Workshop (in Chinese)
14:00 PM to 16:30 PM, Monday, November 23, 2015, Lecture Hall of Lehu Hotel, Shanghai University
Chairs: Jincang Zhang
14:00 PM W-1 (Invited)
Research and Applications for Superconducting Microwave Devices and Systems
Yusheng He
Institute of Physics, Chinese Academy of Sciences, Beijing, China
14:30 PM W-2 (Invited)
69
Expectations and Problems of Applying SMES to Electric Power System
Yuejin Tang
Huazhong University of Science and Technology, Wuhan, China
15:00 PM W-3 (Invited)
Supconducting Fault Current Limiter
Ying Xin
Tianjin University, Tianjin, China
15:30 PM W-4 (Invited)
Practical Superconducting Materials and Their Challenges for Power Applications
Chuanbing Cai
Shanghai University, Shanghai, China
70
ASEMD2015
Shanghai, China
Nov.20-23, 2015
Author Index
08
Index of Sessions
Cui, Y. M.
A
Adamenkov, A. A1-1
Amelichev, V.
A1-1
Ali, M. H.
D3-4
B
Badel, A.
Bagdhadi, M.
Bai. C. Y.
Bao, X. H.
Bartolomé, E.
Bian, Y. B.
Bin, L.
Blednov, A.
3PL-01
2PL-03
A2-2
B2-6
1PL-02
F2-4
B2-3
A1-1
C
Cai, C. B.
Cao, B. S.
Cao, L.
Cao, W. P.
Calleja, A.
Cayado, P.
Chamorro, N.
Chang, K.
Chen, D. X.
Chen, G. X.
Chen, J. Q.
Chen, L.
Chen, M.
Chen, S. Z.
Chen X. Y.
Chen, Y. S.
Chen, Y. Y.
Chen, Z. H.
Cheng, J. S.
Cheng, X. X.
Chepikov, V.
Chikumoto, N.
Chu, G.
Cicéron, J.
Coll, M.
Coombs, T. A.
Cui, C. Y.
Cui, S. M.
A2-2
F2-3
H1-3
D2-2
1PL-02
1PL-02
1PL-02
G-4
A1-4,H1-1
E1-7
A2-4, E2-8
C-7
E2-1
G-4
A1-5, C-9
H1-6
B2-6
A2-4
E1-1,G-5
G-8
A1-1
B1-4
B2-2
3PL-01
1PL-02
2PL-03
B2-8
D1-4
A2-7,E1-5
D
Dai, S. T.
Dai, W.
Dai,Y. M.
Dong, H.
Dong, J.
Dong, J. N.
Dong, K.
Du, B. X.
Du, J. J.
Duan, K. J.
Duan, N. N.
B2-1
G-1
G-5
B1-6
E1-5
H3-3
C-6,G-6
G-3,G-8,G-9
H2-7,H3-8
H2-4
H2-1,H3-2
E
El-Amary, N.H.
D3-4
F
Fan, F.
Fan,Y.
Fang, F. X.
Fang, J.
A2-2
H1-1
H2-2
A1-4,B2-3,
H1-1,E2-5
A2-5
1PL-02
C-3
H2-4
2PL-03
F2-5
E1-4,D2-5
D1-7
B2-2
Fang, Y. Q.
Farjas, J.
Farrok, O.
Feng, X.
Fu, L.
Fu, W.
Fu, W. N.
Fu, X.H.
Fuger, R.
G
Gao, L.
Gao, P.
Gao, Y. H.
Gao, Y. T.
Garzon, A.
Gázquez, J.
Geng, J.
Geng, Y. S.
Gong, K.
Gong, T. Y.
Gorbunova, D.
71
F2-4
D3-8
H2-2
D2-4
1PL-02
1PL-02
2PL-03
A1-6,B2-7
B1-9
B2-5
A1-1
Gou, C. C.
Granados, X.
Guan, W. M.
Guina, A.
Guo, B. C.
Guo, K. G.
Guo, X. B.
Guo, Y. G.
Guo, Y. Q.
E1-6, E2-7
1PL-02
H2-2
B2-2
H3-3
D2-6
F2-3
A1-3, B2-4,D1-5,
C-3,H1-2,
H2-1,H3-2
A2-2
H
Hamabe, M.
Han, T.
Hao, L.
Hao, Y.
Hayakawa, N.
He, F.
He, H. B.
He, Y. S.
Ho, S. L.
Holzapfel, B.
Hong, Z.
Hossain, M. B.
Hu, D.
Hu, M.Q.
Hu, X.N.
Hu, Y.
Hu, Y. P.
Huang, G. H.
Huang, L.
Huang, X. G.
Huang, X. H.
Huang, X. Z.
Huang, Y. K.
Huo, Y. J.
B1-4
G-8
D1-7
H2-6
G-2
A1-7
C-5
F2-4
D2-5
2PL-01
B1-3
A1-3
B1-3
C-6,G-6
E2-6
E2-6
B2-6
A2-5
C-6,G-6
H1-7
F2-5
D3-1
D2-6,H3-3
A1-4
I
Ibrahim, H. E. A. D3-4
Islam, M. R.
A1-3
Ivanov, Y. V.
B1-4
J
Ji, L.
A2-5, F2-2
Ji, J.H.
Jia, J. F.
Jiang, S. Y.
Jiao, Y. J.
Jin, B. B.
Jin F.
Jin, J.X.
D3-5
C-1
H2-3
F2-5
F1-3
A1-5
B1-8, G-3,G-9
K
Kalitka, V.
Kamenev, A.
Kang, R.
Kaul, A.
Kells, J.
Kong, H. Y.
Kong, Y.
Kou, B. Q.
A1-1
A1-1
E1-3
A1-1
B2-2
H2-2
D1-3
D3-7, H1-6
L
Labes, K.
Lahoubi, M.
Lei. G.
Lee, L.
Lee, W.
Lei, G.
Li, B.
Li, B. T.
Li, C. G.
Li, C. S.
Li, D.W.
Li, H.
Li, J.
Li, J. D.
Li, J. L.
Li, J. W.
Li, J. Z.
Li, L. K.
Li, L. N.
Li, L. Y.
Li, N.
Li, Q.
Li, Q. Q.
Li, T. T.
Li, S.
Li, X. T.
Li, Y.
Li, Y. J.
Li, Z.
Li, Z. M.
Li, Z. Y.
Liang, W. Q.
Lin, F.
Lin, H. Y.
Lin, J. K.
Lin, J. X.
Lin, M. Y.
Lissington, T.
Liu E. W.
Liu, F.
Liu, G. H.
Liu, H. J.
B2-2
A2-6
D1-5, H1-2
A1-1
F1-1
B2-4
A1-7, C-1
C-1
F2-4
C-2
D1-1, D2-4
F2-4
D1-1, D3-1, G-3
B1-9
D1-6
A2-2
H3-5
B2-8, G-5
E1-4
F1-6
F2-6
E1-2, H2-3, 3PL-02
A1-7
AP-6
H1-1
B2-5
E1-1, E1-6
E2-2, H1-3
D3-3, H1-4,1PL-02
BP-4, E1-9
B1-3
G-6
E2-6
D2-6
H2-4
A2-2
D1-3,D1-7,F2-6
B2-2
A1-5
E1-1
E2-1
H2-6
Liu, H. W.
Liu, J. H.
Liu, K.
Liu, R. H.
Liu, T.
Liu, W.
Liu, X. M.
Liu, Y.
Liu, Z. Y.
F2-1
E1-6,E2-7,G-5
B2-5
H1-5
F1-5
E1-9
A2-2
B1-9
A2-2, A1-6,
B2-7, G-7
H3-4
A2-2
H3-8
H2-3
H2-3
D2-3
A2-7
H2-7
Liu, Z. Z.
Lu, Y. M.
Lu, H. Y.
Lu, Z.
Luo, G.
Luo, X.
Lu, G.
Lu, H. Y.
M
Ma, G. L.
Ma, G. T.
Ma, Y. H.
Makarevich, A.
Mankevich, A.
Markelov, A.
Martynova, I.
Mashaly,R.I.
MasudRana, M.
Matsekh, A.
Matsuda, K.
Midou, N.
Molodyk, A.
Morrow, J.
Moysykh, M.
Mu, C.X.
Mundet, B.
Muramatsu, K.
E1-9
B2-5
B1-3
A1-1
A1-1
A1-1
A1-1
D3-4
A1-3
B2-2
2PL-03
B1-1
A1-1
D2-2
A1-1
C-5, H3-1
1PL-02
H2-2
N
Ngamroo, I.
Ni, Z. P.
Nijhuis, A.
Niu, S. X.
C-6
E1-1
E2-5
D2-3, D2-5,H2-6
O
Rao, J.
Ren, A.
Ren, L.
Petrykin, V.
Ricart, S.
Ros, J.
Roura, P.
Ryu, K.
D2-4
A1-7
B1-6,B1-9,C-7
A1-1
1PL-02
1PL-02
1PL-02
B1-3
S
Samolienkov, S.
Sánchez, C. F.
Satoru, Y.
Schwartz, J.
Shah, M.
Sheikh, M. R. I.
Shen, S.
Shi, J.
Soler, L.
Solovyov, V.
Song, G. M.
Song, S. S.
Song, Y. T.
Stangl, A.
Su, D. L.
Su, Z. Z.
Sun, B. Y.
Sun, J.
Sun, L.
A1-1
1PL-02
A1-6, B2-7, G-7
1PL-01
1PL-04
C-3
B1-6
B1-9
1PL-02
3PL-03
H2-3
E1-6
2PL-02,E1-3
1PL-02
A2-6
E1-8
H1-7
B1-4
F2-4
T
Takano, H.
Tan, Q.
Tan, Y. X.
Tang, F.
Tang, L.
Tang, T.
Tang, X.
Tang, Y.
Tang, Y. F.
Tang, Y. J.
Tixador, P.
Tu, Q. Z.
B1-4
D3-1
A1-6,
B1-7,B2-7, G-7
C-7
H3-1
B1-2
A2-3
B1-6
C-5
B1-9
3PL-01
H2-4
U
Obradors, X.
Otabe, E. S.
Ou, R.
1PL-02
B1-4
C-2
P
Peng, J. G.
Pi, W.
Pop, C.
Pu, S. L.
Puig, T.
H3-6
E1-5,E1-7
1PL-02
A2-6
1PL-02
Q
Qiu, M.
Qu, R. H.
E1-9
D2-4
R
Rabiul Islam, M. C-3
Palau, A.
1PL-02
72
Usoskin, A.
1PL-02
V
Vachirasriciikul, S.C-6
Vallés, F.
1PL-02
Vilardell, M.
1PL-02
Villarejo, B.
1PL-02
Vlad, V R.
1PL-02
Vyatkin, V. S.
B1-4
W
Wan, Y.
Wang, D.
Wang, D. H.
Wang, G. J.
Wang, H.
D1-4
D2-6 , E1-8
D3-6, H3-7
D2-7
B2-8, E1-1
E2-7, F1-5, F1-6
Wang, J.
Wang, J. H
Wang, J. S.
Wang, K.
Wang, L.
Wang, P.
Wang, Q.
Wang, Q, J.
Wang, Q. L.
Wang, S. H.
Wang, X. H.
Wang, X. L.
Wang, X. P.
Wang, X. Y.
Wang, Y.
Wang, Y. C.
Wang, Y. S.
Wang, Z.
Wang, Z. T.
Watanabe H.
Wei, B.
Wei, W.
Wei, Z. Q.
Wen, J. B.
Wu, C.
Wu, G. L.
Wu, J.
Wu, L. T.
Wu, S. P.
Wu, Y.
Wu, Z. S.
F2-4
1PL-05,A1-6,
B2-7, G-7
B2-5
D3-2, E1-8
E1-6,E1-3,E2-7
D2-7
D1-6
D3-1,D3-3,H1-4
E1-1,B2-8
C-4, H2-1,H3-2
D3-6,H3-7
A2-1
D1-2
D2-7,D3-8,
H2-7,H3-8
B1-3,H3-4
D2-5
A2-2,E1-5
B1-5,E1-9, E1-7
B1-6,F1-6
B2-5
B1-4
F2-3
A2-3
B1-8
H3-5
H2-3
HP-5
H3-6
E1-8
D1-4
F2-4
A1-4
X
Xia, L.
Xiang, B.
Xiao, M.
Xiao, X. Y.
Xie, Q. L.
Xin, Y.
Xing, Y. Q.
Xiong, W.
Xiong, Y. X.
E1-1
A1-6, B1-7,
B2-7,G-7
G-9
C-2
A2-5
B1-8
G-3,G-9
F1-6
E2-8
Xu, D.
Xu, J. Y.
Xu, L.
Xu, W.
D1-3,D1-7,F2-6
E1-1
F2-6
B2-4, C-3,
D1-5,H1-2,H3-1
H2-1,H3-2
B2-8
D1-6
A1-4
Xu, W. J.
Xu, X. N.
Xu, Y. X.
Xue, Y. R.
Y
Yao, Z.
Yamaguchi, S.
Yan, L. G.
Yan, S. L.
Yang, C.
Yang, H.
Yang, H. S.
Yang, K.
Yang, M. M.
Yang, Q. X.
Yang, W. H.
Ye, C. Q.
Yin, L.
Yin, M. L.
Yin, S. W.
You, L. X.
Yu, G. D.
Yu, H. T.
Yu, S. Y.
Yu, T.
Yue, H. W.
Yue, S. H.
B1-3
B1-4
E1-1,E2-6
A2-5
B2-5
D2-6
B1-3
A1-6, B1-7,
B2-7, G-7
F1-3
E2-2,H1-3
E1-1
B2-5
A1-4
A1-7
A2-7
1PL-03
D1-6
C-6,G-6
D1-2
F2-4
A2-5
H1-7
Z
Zha, G. Q.
Zhang, C.
Zhang, C. G.
Zhang, C. H.
Zhang, D. P.
Zhang, G. F.
Zhang, F. G.
Zhang, H.
Zhang, H, J.
Zhang, H. S.
Zhang, J. W.
F1-1
B2-6,D3-2
E2-2, H1-3,H3-7
D3-6
F1-5
F1-6
D1-2
B1-5,B2-5,H1-7
C-4
C-9
A1-7, G-9
73
Zhang, J. X.
Zhang, L.
Zhang, L. C.
Zhang, S. H.
Zhang, S. R.
Zhang, R.
Zhang, W.
Zhang, X.
Zhang, X. B.
Zhang, X. P.
Zhang, X. Q.
Zhang, X. Y.
Zhang, Y.
Zhang, Y. J.
Zhang, Y. K.
Zhao, B. Z.
Zhao, J. L.
Zhao, S. P.
Zhao, W. X.
Zhao, X.
Zhao, X. J.
Zhao, Y.
Zheng, D. N.
Zheng, F.
Zheng, J. Q.
Zheng, J. X.
Zhong, X. H.
Zhou, B.
Zhou, J. B.
Zhou, P. B.
Zhou, S. P.
Zhou, W.
Zhu, G.
Zhu, G. H.
Zhu, J. G.
Zhu, J. H.
Zhu, L. H.
Zou, J. B.
Zou, Z. C.
H2-6
D3-7, H1-6
B2-7
D3-2
F1-5
D1-1
D1-3,D1-7,F2-6
F1-5
E1-8
F2-3
F2-4
B2-3
C-2, D2-2,
D2-6, G-8
H1-5,HP-5
C-1
G-4
D1-7
F1-2
D3-5, E2-1
B1-6, B1-9
A2-5
A2-3
F1-4
F1-3
D3-5
E1-3
B1-2
D3-1
E1-6, E2-7,G-5
B2-5
F1-1
E2-5
G-5
F1-3
B2-4, C-3,
D1-5, H3-2, E2-2,
H1-2,H2-1
E1-9
H3-8
D1-6
C-2
Index of Poster
A
Ai, M. M.
Ai, M. M.
5089 HP-11
5085 DP-8
B
Bai, C. Y.
Bai, C. Y.
Bai, C. Y.
Bai, C. Y.
Bai, C. Y.
Bai, C. Y.
Bai, H.
Bai, L. B.
Bai, L. B.
Bai, L. B.
Bao, H. H.
Bao, H. H.
Bao, H. H.
Bao, X. H.
Bi, D. J.
Bi, D. J.
Bian, X. Y.
5238 AP-10
5299 AP-13
5304 AP-15
5320 AP-17
5322 AP-18
5328 AP-19
5273 HP-26
5374 CP-34
5375 CP-35
5373 HP-36
5193 FP-12
5194 FP-13
5380 DP-32
5221 EP-6
5323 HP-31
5034 FP-2
5162 CP-15
C
Cai, C. B.
Cai, C. B.
Cai, C. B.
Cai, C. B.
Cai, C. B.
Cai, C. B.
Cai, C. B.
Cai, C. B.
Cai, C. B.
Cao, B.S.
Cao, H. Y.
Chang, K.
Chen, A. Q.
Chen, D.
Chen, D.
Chen, D.
Chen, G. X.
Chen, G. X.
Chen, H.
Chen, H. X.
5081 AP-1
5097 AP-2
5238 AP-10
5299 AP-13
5304 AP-15
5320 AP-17
5322 AP-18
5328 AP-19
5391 AP-21
5337 FP-17
5139 HP-14
5286 EP-16
5056 CP-3
5029 CP-1
5027 HP-1
5030 FP-1
5154 AP-5
5146 GP-3
5200 EP-4
5061 HP-7
Chen, J.B.
Chen, J. F.
Chen, J.F.
Chen, J. Q.
Chen, J.Q.
Chen, K.
Chen, L.
Chen, L.
Chen, L.
Chen, S. Z.
Chen, T.
Chen, W. F.
Chen, X. Y.
Chen, X. Y.
Chen, Y.
Chen, Y.
Chen, Y. F.
Chen, Y. Y.
Chen, Z.
Cheng, H. S.
Cheng, J. S.
Cheng, M.
Cheng, S. W.
Cheng, S. W.
Cheng, Y. H.
Cheng, Y. H.
Cheng, Y. H.
Cui, B.
Cui, C. Y.
Cui, C. W.
Cui, G.H.
Cui, Y. J.
Cui, Y. J.
Cui, Y. M.
Chi, C. X.
Chi, C. X.
Cui, C. W.
Cui, C. Y.
Chen, Q.
Cao, R. W.
Cao, H. Y.
Cheng, Y.
5337 FP-17
5114 HP-13
5358 DP-31
5349 HP-33
5350 EP-26
5374 CP-34
5015 BP-17
5114 HP-13
5358 DP-31
5283 EP-14
5170 HP-18
5127 DP-15
5241 CP-20
5015 BP-17
5193 FP-12
5194 FP-13
5373 HP-36
5221 EP-6
5120 CP-10
5289 EP-17
5290 EP-18
5177 DP-21
5349 HP-33
5350 EP-26
5374 CP-34
5375 CP-35
5373 HP-36
5213 GP-9
5290 EP-18
5097 AP-2
5222 DP-23
5369 GP-12
5370 CP-33
5185 AP-9
5238 AP-10
5391 AP-21
5299 AP-13
5292 BP-20
5106 BP-3
5155 BP-8
5137 CP-12
5162 CP-15
D
Dai, R. J.
5069 CP-4
74
Dai, Y. M.
Dai, Y. M.
Dai, Y. M.
Di, J.
Ding, S. Y.
Ding, X. F.
Dou, W. Z.
Du, B. X.
Du, B. X.
Du, B. X.
Du, B. X.
Du, B. X.
Du, B. X.
Du, B. X.
Du, B. X.
Du, B. Y.
Du, Y.
Duan, N. N.
5280 EP-12
5282 EP-13
5289 EP-17
5072 HP-10
5222 DP-23
5273 HP-26
5320 AP-17
5206 GP-7
5239 GP-10
5348 GP-11
5076 GP-2
5153 GP-4
5190 GP-6
5211 GP-8
5213 GP-9
5144 DP-18
5177 DP-21
5256 HP-24
F
Fan, F.
Fan, F.
Fan, X.
Fan, Y.
Fang, C.
Fang, F. X.
Fang, H. Y.
Fang, J.
Fang, J.
Fang, S. H.
Fang, S. H.
Fang, S. H.
Fang, X.
Fang, Y. T.
Fang, Y. T.
Fang, Y. T.
Fang, Y. T.
Fang, Y.T.
Fang, Y. T.
Fang, Z.
Feng, F.
Feng, H. C.
Feng, N. j.
Feng, N. J.
Fu, N. W.
5299 AP-13
5304 AP-15
5099 AP-3
5072 HP-10
5370 CP-33
5357 CP-30
5306 BP-21
5109 BP-4
5184 BP-10
5236 EP-9
5319 DP-27
5235 EP-8
5068 DP-7
5283 EP-14
5286 EP-16
5234 BP-18
5276 EP-10
5122 EP-3
5285 EP-15
5135 CP-11
5240 AP-11
5144 DP-18
5217 EP-5
5210 CP-18
5335 DP-29
Fu, W. N.
Fu, X. H.
Fu, X. H.
Fu, X. H.
Fu, S. S.
5313 HP-30
5236 EP-9
5189 FP-11
5197 BP-11
5244 BP-19
G
Gao, N.
Gao, Q. X.
Gao, Y. H.
Ge, B. J.
Ge, S. Y.
Ge, S . Y.
Geng, Y. S.
Geng, Y. S.
Geng, Y. S.
Geng, Y. S.
Gong, K.
Gong, X.
Gou, C.
Gou, C. C.
Gu, Z. H.
Guan, T.
Guan, T. Y.
Guan, W. M.
Guan, X. H.
Guan, X. H.
Guan, X. H.
Guan, X. H.
Guo, B. C.
Guo, C. C.
Guo, C. C.
Guo, H.
Guo, K. K.
Guo, K. K.
Guo, X. B.
Guo, Y. N.
Guo, Y. G.
Guo, Y. G.
Guo, Y. G.
Guo, Y. G.
Guo, Y. G.
Guo, Y. G.
Guo, Y. G.
5170 HP-18
5028 DP-2
5357 CP-30
5068 DP-7
5243 CP-21
5253 CP-22
5201 BP-13
5205 BP-14
5215 BP-15
5216 BP-16
5360 BP-24
5063 HP-8
5015 BP-17
5292 BP-20
5322 AP-18
5230 DP-26
5222 DP-23
5357 CP-30
5115 FP-4
5116 FP-5
5117 FP-6
5332 FP-15
5319 DP-27
5285 EP-15
5279 EP-11
5273 HP-26
5235 EP-8
5236 EP-9
5337 FP-17
5118 CP-9
5212 HP-19
5114HP-13
5256 HP-24
5206 GP-7
5270 AP-12
5358 DP-31
5092 BP-2
Guo, Y. J.
Guo, Y. Q.
Guo, Y. Q.
Guo, Y. Q.
Guo, Y. Q.
Guo, Y. Q.
Guo, Y. Q.
5346 EP-25
5299 AP-13
5304 AP-15
5320 AP-17
5322 AP-18
5328 AP-19
5391 AP-21
H
Han, P.
Han, T.
Han, T.
Han, Y. W.
Hao, H. J.
Hao, Y.
He, M .J.
He, M. J.
Hong, Z.
Hong, Z.
Hu, D.
Hu, H. M.
Hu, H. M.
Hu, J. X.
Hu, M. Q.
Hu, M. Q.
Hu, M. Q.
Hu, X. N.
Hu, X. N.
Hu, X. N.
Hu, X. M.
Hu, Y.
Hu, Y.
Hu, Y. P.
Hua, X.
Huang, L.
Huang, L.
Huang, L.
Huang, L.
Huang, P. H.
Huang, P. H.
Huang, R. C.
Huang, S. R.
Huang, X. Y.
Huang, X. Y.
5297 EP-20
5206 GP-7
5213 GP-9
5382 BP-26
5313 HP-30
5309 HP-29
5037 DP-3
5039 DP-4
5240 AP-11
5376 BP-25
5376 BP-25
5296 EP-19
5297 EP-20
5306 BP-21
5300 HP-28
5210 CP-18
5217 EP-5
5276 EP-10
5279 EP-11
5070 EP-2
5292 BP-20
5276 EP-10
5070 EP-2
5221 EP-6
5287 CP-28
5300 HP-28
5200 EP-4
5217 EP-5
5198 BP-12
5190 GP-6
5211 GP-8
5015 BP-17
5166 HP-17
5122 EP-3
5234 BP-18
75
Huang, X. Z.
Huangfu, Y. P.
Huangfu, Y. P.
Huo, X. X.
Huo, X. X.
5119 DP-14
5251 HP-22
5255 HP-23
5243 CP-21
5253 CP-22
J
Ji, J. H.
Ji, J. H.
Ji, J. H.
Ji, J. H.
Ji, S. C.
Jia, G. L.
Jia, H. Y.
Jia, S. F.
Jia, Z.
Jiang, G. Z.
Jiang, H. T.
Jiang, J. P.
Jiang, L. N.
Jiang, S.
Jiang, S. H.
Jiang, S. Y.
Jiang, X. J.
Jiang, X. T.
Jiang, Y. J.
Jiang, Z. G.
Jin, B. B.
Jin, J. X.
Jin, J. X.
Jin, J. X.
Jin, J. X.
Jin, J. X.
Jin, J. X.
Jin, J. X.
Jin, Y.
Jin, Z.
Jin, Z.
Jing, L. B.
Jing, L. B.
5100 DP-11
5131 DP-16
5163 FP-7
5165 BP-9
5369 GP-12
5230 DP-26
5127 DP-15
5306 BP-21
5127 DP-15
5114 HP-13
5137 CP-12
5348 GP-11
5337 FP-17
5222 DP-23
5373 HP-36
5042 HP-3
5015 BP-17
5228 DP-25
5179 FP-9
5085 DP-8
5347 FP-18
5270 AP-12
5092 BP-2
5354 BP-23
5265 CP-25
5267 CP-26
5190 GP-6
5211 GP-8
5155 BP-8
5240 AP-11
5376 BP-25
5025 DP-1
5028 DP-2
K
Kong, H. Y.
5357 CP-30
Kreeumporn, W. 5113 BP-6
L
Lee, W.
Lei, G.
Lei, G.
Lei, J. H.
Li, B.
Li, B.
Li, C. S.
Li, C. S.
Li, C. S.
Li, D. W.
Li, D. W.
Li, G. D.
Li, G. H.
Li, G. W.
Li, H. L.
Li, H. L.
Li, H. X.
Li, J.
Li, J.
Li, J.
Li, J.
Li, J.
Li, J. L.
Li, J. W.
Li, J. W.
Li, J. W.
Li, J. Y.
Li, L.
Li, L. K.
Li, L. K.
Li, L. Y.
Li, L. Y.
Li, M.
Li, N.
Li, N.
Li, Q.
Li, Q.
Li, S. G.
Li, T. T.
Li, T. T.
Li, T. T.
5390 AP-20
5057 EP-1
5092 BP-2
5116 FP-5
5362 CP-31
5363 CP-32
5120 CP-10
5138 CP-13
5168 CP-16
5306 BP-21
5334 BP-22
5243 CP-21
5165 BP-9
5161 DP-20
5251 HP-22
5257 CP-23
5356 HP-35
5076 GP-2
5190 GP-6
5206 GP-7
5348 GP-11
5306 BP-21
5171 FP-8
5146 GP-3
5154 AP-5
5301 AP-14
5140 BP-7
5268 HP-25
5290 EP-18
5289 EP-17
5333 DP-28
5343 DP-30
5301 AP-14
5189 FP-11
5231 FP-14
5042 HP-3
5094 C-8
5033 HP-2
5146 GP-3
5154 AP-5
5145 AP-4
Li, T.T.
Li, W. k.
Li, W. T.
Li, W. T.
Li, X.
Li, X.
Li, X. F.
Li, X. H.
Li, X. L.
Li, X. L.
Li, X. N.
Li, X. Q.
Li, X. Y.
Li, X. Y.
Li, X. Y.
Li, X. Y.
Li, X. Y.
Li, Y.
Li, Y.
Li, Y.
Li, Y.
Li, Y.
Li, Y.
Li, Z. M.
Li, Z. Y.
Liang, S. Z.
Liao, W. P.
Lin, C. Y.
Lin, F.
Lin, H. Y.
Lin, K. H.
Lin, M. Y.
Lin, M. Y.
Lin, M. Y.
Lin, M. Y.
Liu, C. C.
Liu, D. S.
Liu, F.
Liu, F.
Liu, F.
Liu, F.
Liu, F. F.
Liu, G. H.
Liu, G. H.
5146 GP-3
5228 DP-25
5166 HP-17
5238 AP-10
5283 EP-14
5286 EP-16
5323 HP-31
5152HP-15
5348 GP-11
5348 GP-11
5184 BP-10
5158 HP-16
5202 CP-17
5210 CP-19
5263 CP-24
5140 BP-7
5176 CP-17
5309 HP-29
5160 DP-19
5228 DP-25
5175 AP-8
5101 CP-7
5135 CP-11
5109 BP-4
5376 BP-25
5122 EP-3
5061 HP-7
5369 GP-12
5334 BP-22
5236 EP-9
5238 AP-10
5236 EP-9
5189 FP-11
5231 FP-14
5197 BP-11
5212 HP-19
5153 GP-4
5065 HP-9
5115 FP-4
5117 FP-6
5066 GP-1
5162 CP-15
5100 DP-11
5163 FP-7
76
Liu, G. H.
Liu, G. H.
Liu, G. H.
Liu, G. L.
Liu, G. W.
Liu, H. J.
Liu, H. J.
Liu, H. W.
Liu, H. W.
Liu, H. W.
Liu, H. W.
Liu, H. X.
Liu, H. Y.
Liu, J.
Liu, J. H.
Liu, J. H.
Liu, J. H.
Liu, J. W.
Liu, K.
Liu, K.
Liu, K.
Liu, L.
Liu, L.
Liu, L.
Liu, L.
Liu, L. K.
Liu, Q. S.
Liu, R.
Liu, T.
Liu, T.
Liu, T.
Liu, W.
Liu, W. Y.
Liu, X. J.
Liu, X. J.
Liu, X. J.
Liu, X. M.
Liu, X. M.
Liu, Y.
Liu, Y.
Liu, Y.
Liu, Y. J.
Liu, Y. L.
Liu, Y. Q.
5163 FP-7
5099 AP-3
5106 BP-3
5273 HP-26
5161 DP-20
5275 HP-27
5309 HP-29
5115 FP-4
5116 FP-5
5117 FP-6
5332 FP-15
5183 DP-22
5313 HP-30
5198 BP-12
5285 EP-15
5283 EP-14
5286 EP-16
5115 FP-4
5236 EP-9
5183 DP-22
5197 BP-11
5025 DP-1
5028 DP-2
5044 FP-3
5030 FP-3
5038 CP-2
5127 DP-15
5137 CP-12
5030 FP-1
5027 HP-1
5029 CP-1
5109 BP-4
5347 FP-18
5297 EP-20
5107 HP-12
5212 HP-19
5097 AP-2
5299 AP-13
5289 EP-17
5360 BP-24
5138 CP-13
5072 HP-10
5335 DP-29
5157 CP-14
Liu, Z. Y.
Liu, Z. Y.
Liu, Z. Y.
Liu, Z. Y.
Liu, Z. Y.
Liu, Z. Y.
Liu, Z. Y.
Liu, Z. Y.
Liu, Z. Y.
Liu, Z. Y.
Liu, Z. Z.
Liu, Z. Z.
Liu, Z. Z.
Liu, Z. Z.
Lu, B. L.
Lu, W. H.
Lu, Y. M.
Lu, Y. M.
Lu, Y. M.
Lu, Y. M.
Lu, Y. M.
Lu, Y. M.
Lu, Z.
Lu. S.
Luo, C. J.
Luo, G.
Luo, S.
Luo, S. A.
Luo, X.
Lu, G.
Lu, G. Q.
5299 AP-13
5304 AP-15
5320 AP-17
5322 AP-18
5328 AP-19
5391 AP-21
5201 BP-13
5205 BP-14
5215 BP-15
5216 BP-16
5061 HP-7
5223 HP-20
5182 FP-10
5182 FP-10
5105 DP-12
5370 CP-33
5299 AP-13
5304 AP-15
5320 AP-17
5322 AP-18
5328 AP-19
5391 AP-21
5042 HP-3
5287 CP-28
5337 FP-17
5042 HP-3
5358 DP-31
5114 HP-13
5336 FP-16
5185 AP-9
5141 DP-17
M
Ma, H. Z.
Ma, L.
Ma, M, N.
Ma, M.
Ma, X. F.
Ma, Z. L.
Ma, Z. L.
Mao, J.
Mao, Y. Y.
Mao, Y.X.
Mei, L.
5198 BP-12
5034 FP-2
5343 DP-30
5333 DP-28
5184 BP-10
5206 GP-7
5206 GP-7
5015 BP-17
5042 HP-3
5100 DP-11
5107 HP-12
Meng, D.
Meng, D. W.
Miao, J. Y.
Mou, Y.
Mou, Y.
Mou, Y.
Mu, C. X.
Mu, C. X.
Mu, C. X.
Mu, C. X.
Mu, C. X.
Mu, C. X.
Mu, C. X.
Muramatsu,
5054 HP-6
5055 DP-6
5174 AP-7
5030 FP-1
5027 HP-1
5029 CP-1
5046 HP-4
5265 CP-25
5040 DP-5
5179 FP-9
5056 CP-3
5069 CP-4
5267 CP-26
5357 CP-30
N
Ngamroo, I.
Ngamroo, I.
Ni, J. J.
Ning, Z. Y.
Niu, P.
Niu, P.
Niu, S. X.
Niu, S. X.
Niu, S. X.
Niu, S. X.
5111 BP-5
5113 BP-6
5141 DP-17
5068 DP-7
5034 FP-2
5034 FP-2
5309 HP-29
5335 DP-29
5336 FP-16
5336 FP-16
O
Ou, R.
Ou, X. B.
Ou, Y. Z.
Ou, Y. Z.
5168 CP-16
5369 GP-12
5362 CP-31
5363 CP-32
P
Peng, J. G.
Peng, L.
Peng, Y.
Peng, Y.
Peng, Y. X.
Peng, Y. X.
Pi, W.
Pi, W.
5044 FP-3
5081 AP-1
5115 FP-4
5116 FP-5
5139 HP-14
5137 CP-12
5146 GP-3
5156 AP-6
77
Q
Qi, G. Z.
Qi, G. Z.
Qiang, T.
Qin, F.
Qin, F.
Qin, M.
Qiu, M.
Qiu, M.
Qu, D. M.
Qu, D. M.
Qu, R. H.
Qu, R. H.
Qu, X. D.
5061 HP-7
5182 FP-10
5119 DP-14
5115 FP-4
5116 FP-5
5184 BP-10
5109 BP-4
5244 BP-19
5182 FP-10
5182 FP-10
5306 BP-21
5334 BP-22
5061 HP-7
R
Ren, B. P.
Ren, B. P.
Ren, B.P.
Ren, H.
Ren, L.
Ren, L.
5117 FP-6
5115 FP-4
5116 FP-5
5391 AP-21
5360 BP-24
5140 BP-7
S
Satoru, Y.
5215 BP-15
Satoru, Y.
Sheng, J.
Shi .X. L.
Shi, C. J.
Shi, C. J.
Shi, C. J.
Shi, J.
Shi, L. W.
Shi, P. T.
Shi, Z. C.
Shi, Z. C.
Shi. X. L.
Song,H. Y.
Song, Y. B.
Su, F. F.
Su, F. F.
5216 BP-16
5376 BP-25
5304 AP-15
5146 GP-3
5154 AP-5
5317 AP-16
5360 BP-24
5110 DP-13
5098 CP-6
5210 CP-18
5217 EP-5
5391 AP-21
5238 AP-10
5205 BP-14
5347 FP-18
5347 FP-18
Su, J.
Su, J. G.
Su, J. G.
Su, Z. Z.
Su, Z. Z.
Sun, R.
Sun, R.
Sun, W. S.
Sun, W. S.
Sun, X. D.
Sun, X. D.
Sun, Y. D.
Sun, Y. X.
5015 BP-17
5213 GP-9
5213 GP-9
5233 EP-7
5346 EP-25
5139 HP-14
5135 CP-11
5290 EP-18
5289 EP-17
5114 HP-13
5358 DP-31
5177 DP-21
5177 DP-21
T
Tan, X. R.
5159 GP-5
Tan, X. R.
Tan, Y. X.
Tang, B.
Tang, B.
Tang, B.
Tang, Y.
Tao, X.
Tao, X.
Tian, M. X.
Tian, M. X.
Tian, X. R.
Tian, Y.
Tian, Y.
Tian, Y.
Tian, Y. X.
Tian, Y. X.
5159 GP-5
5215 BP-15
5139 HP-14
5135 CP-11
5137 CP-12
5140 BP-7
5255 HP-23
5257 CP-23
5098 CP-6
5118 CP-9
5157 CP-14
5228 DP-25
5347 FP-18
5347 FP-18
5201 BP-13
5205 BP-14
W
W, X. D.
5144 DP-18
Wang, Z.
Wang, B.
Wang, D.
Wang, D.
Wang, D.
Wang, D.
Wang, D.
Wang, D. H.
Wang, D. H.
5068 DP-7
5236 EP-9
5349 HP-33
5236 EP-9
5233 EP-7
5350 EP-26
5346 EP-25
5312 EP-22
5225 DP-24
Wang, D. M.
Wang, H.
Wang, H.
Wang, H.
Wang, H.
Wang, H. L.
Wang, H. S.
Wang, H. S.
Wang, H. T.
Wang, J.
Wang, J. H.
Wang, J. H.
Wang, J. H.
Wang, K.
Wang, K.
Wang, L. Y.
Wang, L. Y.
Wang, M, M.
Wang, M. Q.
Wang, Q.
Wang, Q.
Wang, Q.
Wang, Q.
Wang, Q. l.
Wang, S.
Wang, S.
Wang, S. C.
Wang, S. H.
Wang, S. H.
Wang, S. H.
Wang, S. H.
Wang, S. H.
Wang, S. H.
Wang, S. Y.
Wang, X. D.
Wang, X. G.
Wang, X. G.
Wang, X. H.
Wang, X. H.
Wang, X. H.
Wang, Y.
Wang, Y. F.
Wang, Y. H.
Wang, Y. L.
78
5107 HP-12
5279 EP-11
5292 BP-20
5282 EP-13
5286 EP-16
5140 BP-7
5285 EP-15
5283 EP-14
5319 DP-27
5275 HP-27
5201 BP-13
5215 BP-15
5216 BP-16
5090 DP-9
5233 EP-7
5170 HP-18
5287 CP-27
5370 CP-33
5222 DP-23
5054 HP-6
5160 DP-19
5171 FP-8
5171 FP-8
5070 EP-2
5251 HP-22
5255 HP-23
5354 BP-23
5251 HP-22
5256 HP-24
5250 HP-21
5351 HP-34
5257 CP-23
5201 BP-13
5131 DP-16
5253 CP-22
5152 HP-15
5076 GP-2
5170 HP-18
5312 EP-22
5225 DP-24
5223 HP-20
5287 CP-28
5212 HP-19
5354 BP-23
Wang, Y. S.
Wang, Y. S.
Wang, Y. S.
Wang, Y. S.
Wang, Y. S.
Wang, Y. S.
Wang, Y. S.
Wang, Y. S.
Wang, Y. S.
Wang, Y. S.
Wang, Z. Y.
Wei, Bi.
Wei, Bi.
Wei, D.
Wei, Y. H.
Wei, Y. H.
Wei, Y. H.
Wei, Y. H.
Wei, Y. H.
Wei, Y. Y.
Wen, P.
Wen, P.
Wen, P.
Wu, C. T.
Wu, D. Y.
Wu, L. T.
Wu, W.
Wu, X. Z.
Wu, X. Z.
Wu, Z.
5146 GP-3
5154 AP-5
5156 AP-6
5174 AP-7
5175 AP-8
5185 AP-9
5301 AP-14
5317 AP-16
5078 BP-1
5145 AP-4
5057 EP-1
5337 FP-17
5337 FP-17
5384 BP-27
5030 FP-1
5027 HP-1
5027 HP-1
5029 CP-1
5030 FP-1
5171 FP-8
5115 FP-4
5116 FP-5
5332 FP-15
5287 CP-27
5168 CP-16
5233 EP-7
5240 AP-11
5090 DP-9
5091 DP-10
5139 HP-14
X
Xia, Y. Y.
5054 HP-6
Xia, Y. Y.
Xiang, B.
Xiao, F.
Xiao, M.
Xiao, X. Y.
Xiao, X. Y.
Xiao, X. Y.
Xie, X.
Xie, Y. L.
Xie, Y. L.
Xing, X.
5055 DP-6
5205 BP-14
5177 DP-21
5239 GP-10
5120 CP-10
5138 CP-13
5168 CP-16
5323 HP-31
5323 HP-31
5034 FP-2
5287 CP-28
Xing, Y. Q.
Xing, Y. Q.
Xing, Y. Q.
Xing, Y. Q.
Xing, Y. Q.
Xing, Z, X.
Xiong, B.
Xiong, B.
Xiong, Y. X.
Xiong, Y. X.
Xu, D.
Xu, H. K.
Xu, J. W.
Xu, J. W.
Xu, J. W.
Xu, K.
Xu, L.
Xu, L.
Xu, L.
Xu, L.
Xu, W.
Xu, W.
Xu, W.
Xu, W.
Xu, W.
Xu, W.
Xu, W.
Xu, W.
Xu, W.
Xu, W.
Xu, W.
Xu, W.
Xu, W.
Xu, W.
Xu, W.
Xu, W.
Xu, W. J.
Xu, X. Z.
Xu, Y. L.
Xu, Y. l.
Xu, Y. M.
Xu, Y. M.
Xu, Y. M.
Xu, Y. M.
5076 GP-2
5190 GP-6
5211 GP-8
5239 GP-10
5348 GP-11
5102 CP-8
5215 BP-15
5216 BP-16
5350 EP-26
5346 EP-25
5231 FP-14
5347 FP-18
5285 EP-15
5279 EP-11
5292 BP-20
5061 HP-7
5189 FP-11
5231 FP-14
5099 AP-3
5165 BP-9
5296 EP-19
5297 EP-20
5046 HP-4
5152 HP-15
5047 H2-5
5265 CP-25
5267 CP-26
5037 DP-3
5039 DP-4
5040 DP-5
5057 EP-1
5179 FP-9
5092 BP-2
5038 CP-2
5056 CP-3
5069 CP-4
5256 HP-24
5144 DP-18
5063 HP-8
5105 DP-12
5065 HP-9
5089 HP-11
5085 DP-8
5066 GP-1
Xu, Y. M.
Xu, Y. X.
Xu, Y. X.
Xu, Z. W.
Xue, H.
5066 GP-1
5160 DP-19
5171 FP-8
5296 EP-19
5356 HP-35
Y
Yan, J.
5205 BP-14
Yan, K.
Yan, L. G.
Yan, L. G.
Yan, N.
Yan, Y. C.
Yang, F.
Yang, F.
Yang, F.
Yang, G.
Yang, H.
Yang, H.
Yang, H. Y.
Yang, K.
Yang, K.
Yang, L.
Yang, M. M.
Yang, X.
Yang, Y.
Yang, Y.
Yang, Y.
Yang, Y.
Yang, Z. B.
Yang, Z. B.
Yang, Z. X.
Yang, Z. X.
5280 EP-12
5276 EP-10
5070 EP-2
5102 CP-8
5141 DP-17
5373 HP-36
5320 AP-17
5328 AP-19
5268 HP-25
5236 EP-9
5235 EP-8
5183 DP-22
5205 BP-14
5215 BP-15
5119 DP-14
5347 FP-18
5089 HP-11
5061 HP-7
5182 FP-10
5193 FP-12
5194 FP-13
5114 HP-13
5358 DP-31
5030 FP-1
5027 HP-1
Yang, Z. X.
5029 CP-1
Yao, K.
Yi, X.Q.
Yin, C.
Yin, C.
Yin, C.
Yin, L.
Yu, G. D.
Yu, H. T.
Yu, H. T.
Yu, H. T.
5094 C-8
5346 EP-25
5373 HP-36
5374 CP-34
5375 CP-35
5184 BP-10
5171 FP-8
5300 HP-28
5200 EP-4
5217 EP-5
79
Yu, H.T.
Yu, J.
Yu, J.
Yu, L.
Yu, Y.
Yu, Z. S.
Yu, Z. S.
Yuan, D. S.
Yuan, D. S.
Yuan, S. J.
Yuan, W. J.
5210 CP-18
5320 AP-17
5322 AP-18
5127 DP-15
5213 GP-9
5349 HP-33
5350 EP-26
5255 HP-23
5257 CP-23
5170 HP-18
5244 BP-19
Z
Zeng, Y.
5106 BP-3
Zha, G. Q.
5390 AP-20
Zhang , H.
Zhang, B.
Zhang, B.
5078 BP-1
5159 GP-5
5101 CP-7
Zhang, C.
5221 EP-6
Zhang, C. H.
Zhang, C. H.
Zhang, D.
Zhang, D. Y.
Zhang, F.
Zhang, F. G.
5312 EP-22
5225 DP-24
5243 CP-21
5384 BP-27
5370 CP-33
5230 DP-26
Zhang, G. G.
5161 DP-20
Zhang, G. M.
Zhang, G. Q.
Zhang, H. J.
Zhang, H. M.
5107 HP-12
5338 CP-29
5257 CP-23
5244 BP-19
Zhang, H. S.
5241 CP-20
Zhang, J.
Zhang, J.
Zhang, J.
Zhang, J. G.
Zhang, J. W.
Zhang, J. X.
Zhang, K. H.
Zhang, L. H.
Zhang, M.
Zhang, N. M.
Zhang, N. M.
Zhang, S. N.
Zhang, T.
5300 HP-28
5374 CP-34
5375 CP-35
5153 GP-4
5239 GP-10
5309 HP-29
5234 BP-18
5360 BP-24
5244 BP-19
5250 HP-21
5351 HP-34
5183 DP-22
5158 HP-16
Zhang, T.
Zhang, T.
Zhang, W.
Zhang, W.
Zhang, W.
Zhang, X.
Zhang, X. B.
Zhang, X. L.
Zhang, X. Z.
Zhang, Y.
Zhang, Y.
Zhang, Y.
Zhang, Y.
Zhang, Y. P.
Zhang, Y. P.
Zhang, Y. Z.
Zhang, Z. Q.
Zhang, Z. Y.
Zhang, Z. Y.
Zhao, H.
Zhao, H. Y.
Zhao, M.
Zhao, S. C.
Zhao, S. P.
Zhao, W. X.
5159 GP-5
5157 CP-14
5193 FP-12
5194 FP-13
5231 FP-14
5326 HP-32
5233 EP-7
5268 HP-25
5382 BP-26
5090 DP-9
5091 DP-10
5235 EP-8
5030 FP-1
5027 HP-1
5029 CP-1
5155 BP-8
5055 DP-6
5313 HP-30
5299 AP-13
5033 HP-2
5094 C-8
5183 DP-22
5322 AP-18
5347 FP-18
5100 DP-11
Zhao, W. X.
5131 DP-16
Zhao, W. X.
Zhao, W. X.
Zhao, W. X.
Zhao, W. X.
Zhao, Y.
Zhao, Y.
Zheng, F.
Zheng, J. Q.
Zheng, X. D.
Zheng, X. D.
Zheng, Y.
Zheng, Z. X.
Zhong, W. B.
Zhong, W. B.
Zhou, A. B.
Zhou, B.
Zhou, B.
Zhou, D.
Zhou, F.
Zhou, J. B.
Zhou, J. B.
Zhou, Q. B.
Zhou, Q. W.
Zhou, S. P.
Zhou, X.
Zhou, Z. C.
80
5163 FP-7
5099 AP-3
5106 BP-3
5165 BP-9
5152 HP-15
5240 AP-11
5347 FP-18
5163 FP-7
5109 BP-4
5184 BP-10
5230 DP-26
5138 CP-13
5210 CP-18
5217 EP-5
5360 BP-24
5110 DP-13
5119 DP-14
5369 GP-12
5290 EP-18
5279 EP-11
5292 BP-20
5162 CP-15
5370 CP-33
5390 AP-20
5360 BP-24
5168 CP-16
Zhu, G. H
Zhu, H. Q.
Zhu, J. G.
Zhu, J. G.
Zhu, J. G.
5347 FP-18
5177 DP-21
5212 HP-19
5251 HP-22
5256 HP-24
Zhu, J. G.
5358 DP-31
Zhu, J. G.
Zhu, J. G.
5057 EP-1
5092 BP-2
Zhu, J. G.
5270 AP-12
Zhu, J. H.
5109 BP-4
Zhu, J. H.
5184 BP-10
Zhu, J. H.
Zhu, L.
Zhu, S. S.
Zhu, X. H.
Zhu, X. Y.
Zhu, Y. H.
Zhu, Y. Y.
Zou, J. B.
Zou, J. B.
Zou, J. B.
Zou, J. Q.
Zou, Q.
5244 BP-19
5369 GP-12
5332 FP-15
5253 CP-22
5177 DP-21
5350 EP-26
5370 CP-33
5160 DP-19
5183 DP-22
5171 FP-8
5047 H2-5
5158 HP-16
Note
Exhibitions
ZUFA
Company Profile：Hengli Eletek Co., Ltd. was founded in 1992 with the mission to
become a leading supplier of thermal processing solutions to the global electronics and
materials markets. The company is currently headquartered in Hefei, China. Hengli conveyor
belt furnaces are widely used in industries such as microelectronic packaging (including lC,
SMT, HIC, MCM and MEMS manufacturing), solar cell (photovoltaic) manufacturing, as well as
advanced materials processing. In addition, Hengli manufactures surface treatment lines for
electronic and military markets and custom systems for specific customer applications.
With the promise of high efficiency, high performance, high reliability, and low cost, all
Hengli associates serve their customers with honesty, integrity and value．Hengli products and
services have been highly appreciated by customers from more than 20 countries & regions
located in North America, South America, Europe, Asia, and Australia. You are sincerely
invited to visit Hengli and try their innovative products.
business philosophy: integrity and win-win innovation and development focus on
customer excellence Constant has always adhere to customer-centric, rapid response to
customer demand, in good faith and common growth, innovation and creative thinking with
technology development, and strive to achieve the electronics industry dedicated excellent
equipment supplier.
Contact Us： NO.19 Hehuan Road, New & High Tech Development Zone, Anhui, China 230088;
Tel: 0551-65846903 Fax: 0551-65846907
218 Xinghu Street, Suzhou Industrial Park, Jiangshu Province, China 215123
Tel：0512-67900119
Suzhou Advanced Materials Research Institute Incorporated
Suzhou Advanced Materials Research Institute Incorporated (SAMRI) was
established in January of 2011. Its 5000-m2 facility is located by the scenic Dushu Lake in
Suzhou Industrial Park (SIP). The total investment so far is 500 Million CNY, jointly funded
by the Etern Group of China and the China-Singapore SIP Venture Fund. SAMRI develops
and manufactures the advanced km-class high-temperature superconducting (HTS) tapes
with YBa2Cu3O7- film as conducting layer, and the application devices as well. With a
strong technical team, the company is the lead organization responsible for the completion
of a national “863” high-tech project “Development of Advanced Superconducting
Materials” during the 12th five-year term.
Our company has established the China’s first complete production line for the
advanced HTS tapes in a 10000-class clean room. The yearly production capacity is
600km. 5 types of product with world-class performance are available now. The technical
specs are listed in the following tables:
Product Type
Minimum Ic（A）
Width（mm）
SCCS
Premium SCCS
DCCS
SCSS
12mm w/o Cu
100
150
160
250
300
4.5
4.5
4.5
12
12
0.18-0.20
0.18-0.20
0.23-0.25
0.2-0.3
0.105
Thickness of Stabilizer（mm）
0.1
0.1
0.1
0.1-0.25
0
Critical Tensile Stress（MPa）
400
400
400
450
550
25
25
30
50
10
Total Thickness（mm）
Crtical Bend Radius（mm）
Recommended Applications
Power Cables,Propulsion Motor, EM Launcher, Plasma Rocket,
Wind/Hydraulic Generators, SMES, etc.
Resistive-Type Fault Current Limiter
SCCS: Single-Core w/o Cu Stabilizer; DCCS: Double-Core w/o Cu Stabilizer; SCSS: Single-Core w/o S.S. Stabilizer
SAMRI also produces and sales metal-organic precursors as listed as follows:
Contact：Mr. Lei Guan Email: guanlei@samri.org.cn Mobile：86.13962699288
Acknowledgement