INVITATION TO TENDER
AND
INSTRUCTIONS TO TENDERERS






Lab Equipment
Networking Labs
Softwares
Desktop Computers
On-Line 10 KVA & 15 KVA UPS
Furniture (Computer Chairs, Computer Tables, Executive Chairs, Seminar
Hall Chairs, Drawing Tables, 3-seater Desks, Single Bed Cot, Reading
Tables, S-type Chairs, etc.,)
 Air Conditioners
JNTUA COLLEGE OF ENGINEERING PULIVENDULA
Y.S.R. DISTRICT, PIN – 516 390
JNTUA COLLEGE OF ENGINEERING, PULIVENDULA
INVITATION TO TENDER AND
INSTRUCTIONS TO TENDERERS
FOR THE SUPPLY OF LAB EQUIPMENT NETWORKING LABS SOFTWARES,
FURNITURE AIR CONDITIONERS, 10KVA, 15KVA UPS & SEVERS etc.
JNTUA College of Engineering, Pulivendula invites tenders for the supply of lab equipment
networking of labs, softwares, furniture, air conditioners, 10KVA, 15KVA UPS & Severs etc. for
JNTUA College of Engineering, Pulivendula, as per specifications given in the schedules attached to
the Tender form annexed hereto. All offers should be made in English and should be written in both
figures and words.
The tender schedules can be obtained from the Principal, JNTUA College of Engineering,
Pulivendula on payment of Rs.2,250/- (Rs.2,000/- +12.5% Sales Tax) in the form of crossed Demand
Draft on any Nationalised Bank drawn in favour of the “Principal, JNTUA College of Engineering,
Pulivendula” payable at Pulivendula. Alternatively the tender schedules can be downloaded from the
website www.jntua.ac.in. Such vendors who use downloaded tender schedules for submitting bids
must enclose a demand draft for Rs.2,000/- +12.5% Sales Tax towards the tender fee along with the
bid in addition to EMD, otherwise the bid will be rejected.
Tender fee once paid is neither refundable nor adjustable for other tenders.
The JNTUA College of Engineering, Pulivendula reserves the right to select certain items (in
single or multiple units) and reject the others mentioned in the schedule. The institution reserves the
right to place the orders for individual items with different vendors. The JNTUA College of
Engineering, Pulivendula also reserves the right to revise or alter the specifications of the lab
equipment before acceptance of any tender.
Incomplete tenders, amendments and additions to tender after opening or late tenders are liable
to be ignored, and rejected.
EMD:
A Demand Draft, for an amount @2% of the estimated value of the schedule(s) for which the
tenderer is submitting the bid, drawn in favour of the “Principal, JNTUA College of Engineering,
Pulivendula” towards EMD must accompany the tender. Those without EMD will be rejected. The
EMD will be refunded to all the unsuccessful tenderers only after the purchase orders are placed on the
successful tenderer. The successful tenderer has to deposit an additional amount @3% on the contract
value as security money deposit.
The final acceptance of the material will be made only after delivering in good condition and
subject to satisfying specifications given by the college.
Vendor
BID PRICE:
1.
The contract shall be for the full quantity as described in the tender. Corrections, if any, shall
be made by crossing out, initialling, dating and re-writing.
2.
All duties, taxes and other levies payable by the vendor shall be included in the total price.
3.
The rates quoted by the bidder shall be fixed for the duration of the contract and shall be
included in the total price.
4.
The prices should be quoted in Indian Rupees only.
5.
The prices should be quoted with FOR destination.
6.
Packing, forwarding, insurance etc to vendors account.
7.
After satisfactory installation, testing and demonstration, training has to be provided to faculty
and staff to the satisfaction of the purchaser at vendor’s cost.
8.
The operation and maintenance manuals and lab manuals are to be supplied at vender’s cost.
9.
All essential accessories cost must be included in the price quoted.
10.
The cost of essential spares are to be quoted separately. This will be taken to into
consideration while bids are evaluated.
11.
Price bids are to be essentially signed by the vendor or person authorized by him.
12.
Each bidder shall submit only one quotation. Alternatives offer option, if any, must be
quoted in separate tender schedule.
VALIDITY OF QUOTATION
Quotation shall remain valid for a period of three months after the deadline date specified for
submission. The vendor shall extend the validity if required.
BIDDER QUALIFICATIONS
1.
Bidder must be a registered company with Sales Tax and Excise Departments and a true copy
of the such registration should be submitted along with the bid.
2.
The bidder should submit the financial turnover report for the last three years.
3.
The bidders should submit the list of customers along with year of supply and details of
equipment supplied.
4.
The bidders should submit Satisfactory Performance Certificates from the customers of this
equipment. The product approval certificate, if any, from reputed organizations may also be
submitted.
Vendor
EVALUATION OF QUOTATIONS:
The purchaser will evaluate and compare the quotations determined to be substantially
responsive i.e which
a) Are properly signed; and
b) Conform to the terms and conditions, and specifications mentioned in this
c) The quotations unless otherwise specified would be evaluated separately for each item
d) If the bidder is not the Original Equipment Manufacturer (OEM) they must Provide an
authorization certificate from the Original Equipment Manufacturer, stating that the bidder is
an approved agent of OEM and service warranty will be guaranteed by OEM in case the
agent’s license is aborted or any other reason whatsoever during the warranty period.
AWARD OF CONTRACT:
The purchaser will award the contract to the bidder whose quotation has been determined to be
substantially responsive and who has offered the lowest evaluated quotation price.
1.
Notwithstanding the above, the purchaser reserves the right to accept or reject any quotations
and to cancel the bidding process and reject all quotations at any time prior to the award of
contract.
2.
The institution reserves the right to place the orders for individual items with different
tenders.
3.
Right to Acceptance:
The Principal, JNTUA College of Engineering, Pulivendula does not bind himself to accept
the lowest on any tender and reserves to himself the right of accepting the whole or any part of
the tender or portion of the quantity offered the tenderer shall supply the same at the rate
quoted.
4.
The bidder, whose bid is accepted, will be notified for the award of contract by the purchaser
prior to expiry of the quotation validity period. The terms of the accepted offer shall be
incorporated in the purchase order.
DELIVERY:
All the goods ordered shall be delivered with proper packing within 15 days from the date of
issue of order.
Vendor
TERMS OF PAYMENT:
a)
Payment shall be made by JNTU College of Engineering, Pulivendula, after delivery at the
specified location, and after installation, commissioning and satisfactory demonstration
of
the goods with all specifications and standards to the entire satisfaction of the college.
b)
The bidder may give the details of bank and Account into which the payments are to be made.
c)
Normal commercial warranty/guarantee shall be applicable to the supplied goods.
DELIVERY OF TENDER:
Bids for each schedule of the tender is to be placed in separate envelope, clearly mentioning
schedule No. on it, and all these envelopes containing quotations for individual schedules are to be
placed in a bigger envelope. The Bigger Envelope must be super-scribed with the reference
No.(JNTUA/CEP/Tender Notice-2/2012, Date:05-05-2012)
The sealed tender should be addressed to:
The Principal,
JNTUA College of Engineering,
Pulivendula, YSR Dist.
Pin code: 516 390.
Bids in sealed covers should reach the above address latest by 4:00 PM hours on 28-052012. Tenders submitted after the specified time shall not be considered and no intimation will
be sent in this regard.
The college reserves the Right to reject any tender which fails to comply with the above
instructions. All tenders should be sent by Post or through messenger, to drop the tender in the sealed
tender box provided in the office. It is the responsibility of the tenderer to see that his tender offer is
delivered by the specified time at the above address. All further communication should be addressed to
the officer named above and by title only.
OTHER TERMS:
Tenderer should make their representative available on 28-05-2012 at 4:00 PM at the time of
opening tenders in the chambers of Principal or any other designated place within the college.
The temderer should produce Value Added Tax (VAT)-Registration certificate.
Tenderer should be responsible and bear any price escalation within the validity period
and also after the indent has been placed till the supply.
Sd/-PRINCIPAL
BID PARTICULARS
1.
Name of the Supplier
:
2.
Address of the Supplier
:
3.
Address of the Show Room/Workshop
:
4.
Display of goods
:
Yes / No
5.
EMD enclosed
:
Yes / No
DD No._____________ Bank:__________________________ Amount_________
6.
Name and address of the officer to whom all reference shall be made regarding this
tender enquiry
Name
:
Address
:
Telephone No. :
Fax No.
:
Mobile No.
:
e-mail
:
web
:
FORMAT OF QUOTATION
S.No
Schedule No...
(As given in the
Annexure)
Description
Goods
Specifications
Qty
Unit
Quoted Unit
rate in Rs.
Total Amount
In Figures
In words
Gross Total Cost: Rs...............................
We agree to supply the above goods in accordance with the technical specifications for a total
contract price of Rs....................... (Amount in figures)......................................... (Rs. Amount in
words) within the period specified in the invitation for Quotations.
We also confirm that the normal commercial warrantee / guarantee of ............... months shall
apply to the offered goods.
Signature for Supplier
ABSTRACT OF EQUIPMENT
Dept.
Schedule No
E.1
EEE
ECE
Bio-Tech
CSE Dept.
Chemistry
E.1.a
E.1.b
E.2
E.3
E.4
E.5
E-5.a
E.5.b
E.5.c
E.5.d
E.5.e
E.6.
E-7
E.8
E.8.a
E.8.b
E.8.c
E.8.d
E.8.e
E.8.f
E.8.g
E.8.h
E.8.i
E.8.j
E.8.k
E.8.l
E.8.m
E.8.n
E.9
E.9.a
E.9.b
E.9.c
E.9.d
E.9.e
E.9.f
E.10
E-11
E-12
Name of the Furniture/ Name of the Lab
Simulation Lab
Power System Software Packages
Mi-Power
PSCAD
Electrical Machines Lab
Power Electronics Lab
Power Systems Lab
Digital IC Design and Communication Lab
Xilinx Software (latest version) (10.1 I)
FPGA Trainer Kits
CPLD Trainer Kits
MAT LAB
Communication
MAT Lab Tool Boxes
simulink
Digital Signal Processor Kits
CRO
Microwave & Optical Communication Lab
Plant Tissue Culture Lab
Laminar airflow
Autoclave
Electronic Weighing Balance
Compound Microscope
Double Distillation Unit
Digital Ph Meter
Hot air oven
Green house facility
Refrigerator
Culture racks
Cooling centrifuge
Shaker incubator
Plant metabolite Extractor (soxillate)
Digital camera for explants documentation
Microbiology Laboratory
Floroscent Spectrophotometer
Gel Doc
Millipore Water purifier
Micro pippets
Ultra centrifuge
TDS conductivity meter
Microsoft Office Software
INFRARED SPECTROMETER (FTIR)
Gas Chromatography
Quantity
Estimated Amount
05 Users
02 Users
500000=00
300000=00
900000=00
295000=00
485000=00
25 users
10
10
25
02
20
30
500000=00
250000=00
250000=00
500000=00
01
01
01
01
01
01
01
01
01
01
01
01
01
01
60000=00
30000=00
23000=00
12000=00
53000=00
15000=00
40000=00
21000=00
40000=00
30000=00
70000=00
28000=00
20000=00
25000=00
01
01
01
20 Nos
01
01
30 users licenses
01
01
800000=00
600000=00
405000=00
500000=00
300000=00
600000=00
200000=00
500000=00
30000=00
150000=00
1100000=00
1050000=00
E.13
Physics
Mathematics
E-13.a
E-13.b
E-13.c
E-13.d
E-13.e
E-13.f
E-13.g
E-13.h
E-13.i
E-13.j
E-13.k
E-13.l
Ball Mill
Furnace
Hydraulic Pellet Press
Spin-coating Unit
Vacuum Coating Unit
LCR meter
Electrometer
Ferroelectric loop tracer
Oven
Magnetic Stirrer
Electronic Weighing Machine
Mortar-pestle
E-14
E. 14.a
E. 14.b
Computational Fluid Dynamics Lab
Mat Lab Software
Mathematica Software
01
01
01
01
01
01
01
01
01
02
01
01
500000=00
700000=00
300000=00
100000=00
500000=00
500000=00
800000=00
500000=00
100000=00
10000=00
50000=00
10000=00
10
10
400000=00
400000=00
Desk Top Computers and Other Items
Schedule No
S.1
S.2
S.2.a
S.2.b
S.2.c
S.2.d
S.3
S.4
S.5
S.6
S.6.a
S.6.b
S.6.c
S.6.d
S.7
S.7.a
S.7.b
S.7.c
S.9
S.9.a
S.9.b
S.9.c
S.10
S.10 (a)
S.10 (b)
Name of the Furniture/ Name of the Lab
Desk Top Computers
Net working
Net working (LAN)
Net working
Net working Internet connection
Net Working Internet connectivity
10 KVA Online UPS
15 KVA Online UPS
Air Conditioners
Printers
1. Laser jet printer with 12A cartridge
2. Desk jet printer
3. Dot Matrix Printer
1. Laser Jet Color Printer
2. Laser Jet Black and White
Printer
Printer cum scanner
Quantity
Estimated Amount
176
6170000=00
40 systems
65 systems
30 systems
10 systems
04
01
93
100000=00
120000=00
60000=00
30000=00
1000000=00
450000=00
3436000=00
04
02
01
01
01
01
02
70000=00
50000=00
20000=00
16000=00
Server
Server System
Server System
Server System
LCD Projector
LCD Projector
LCD Projector
LCD Projector
PAO System & Mike Set with Sound System
PAO System
Mike Set with sound system
01
02
01
300000=00
500000=00
200000=00
01
01
01
200000=00
60000=00
60000=00
02
01
100000=00
40000=00
Furniture
Schedule No
Name of the Furniture/ Name of the Lab
Quantity
F.1
F.2
F.3
F.3.a
F.3.b
F.4
F.4.a
F.4.b
F.4.c
F.4.d
F.5
F.5.a
F.5.b
F.6
Computer Table
Computer Chair
Modular Chairs
Modular Chairs
Modular Chairs
Executive Chairs
Executive Chairs
Executive Chairs
Executive Chairs
Executive Chairs
Acoustic system design for seminar halls
Acoustic system design (EEE)
Acoustic System design (ME)
Chair with attached Planck
Modular Furniture for 30 computers
(Computer Chair + Table + Partition work)
Laboratory Tables
Laboratory Stools
Table with electrical plug points, lockers, racks, acid proof
sheets
Seminar Hall Chairs
Class Room Boards Green
3-seater Desks
Podium
Dias
Dias
Dias (3 class rooms + 4)
Notice Board
Group Discussion Table
Lab working table
Single Bed cot with racks
Reading table
S-Type Chairs
Furniture for Lab
 MODULAR Wall BENCH (IN ‘u’ SHAPE
 MODULAR island BENCH
 wall mounted storage unit
110
110
500000=00
330000=00
240
300
720000=00
900000=00
30
30
25
30
150000=00
150000=00
100000=00
99000=00
30
30
250000=00
250000=00
150000=00
390000=00
F.7
F.8
F.9
F.10
F.11
F.12
F.13
F.14
F.15
F.15.a
F.15.b
F.16
F.17
F.18
F.19
F.20
F.21
F.22
24
96
06
Estimated Amount
288000=00
144000=00
168000=00
100
07
60
04
500000=00
42000=00
600000=00
40000=00
02
07
06
01
05
350
250
250
70000=00
210000=00
60000=00
30000=00
300000=00
2250000=00
600000=00
225000=00
200000=00
REGISTRAR i/c
SCHEDULE OF FURNITURE SPECIFICATIONS, SPECIAL TERMS AND CONDITIONS
FOR THE ITEMS IN SCHEDULES F1, F2, F3, F4, F5, F6, F7, F11, F13, F19 & F22
1.
Only the technically proficient companies who have a turn over exceeding Rs.100 lakhs, annually, and
who have executed projects of similar nature (at least Rs. 30.00 Lakhs in single order) in the past can
submit the quotations.
2.
As a proof of experience / competence, the suppliers should submit along with their quotation, a
statement showing similar nature of work as detailed above executed by them and also credentials from
the clients with whom there have worked for successful completion of their work. They should also
submit a list of their organizations, equipment available with them.
3.
The manufacturer should have in-house design and development capability to take care of any
modifications required in their products to suit the needs of the Principal, JNTUA College of
Engineering, Pulivendula.
4.
The manufacturer should be having in-house capability for manufacturing parts/components critical to
furniture equipment. The manufacturer should be able to exhibit in-house capability in terms of
moulding, welding, panel cutting and sizing and antirust treatment facility. Also should be having fully
automated powder coating booth, router machine, edge binder machine and hot press.
5.
For similar type of projects, the manufacturer must issue a letter of authorization that the vendor has
carried out or capable to implement new technology solutions based on their equipments. The letter of
authorization shall be signed by any person at below the rank of the Branch Manager of the region.
6.
The manufacturer should have capability to provide after sales service and should be in a position to
offer annual maintenance contract, at the premises of JNTUA College of Engineering, Pulivendula.
7.
The manufacturer should have affiliation with reputed body of furniture manufacturers and in-house
testing facility for establishing performance standards of the products.
8.
The supplier who do not fulfill the requisite qualifications and who do not finish documentary evidence
will be summarily rejected. Any misleading information will lead to disqualification of the tender.
9.
The supplier should be willing to get manufacturing capabilities inspected by the tendering committee
to judge the level of competency for undertaking the project. The manufacturer has to maintain the
location of the factory with all details.
10.
A Proof of certifications, agreements, and rate contract from Central and State Government
organization should be enclosed.
11.
The supplier should submit the proof of excise duty and sales tax certifications.
12.
The commercial bids should contain the following details clearly:
a) Unit price of each item to be indicated.
b) Sales tax if applicable
c) Customs duty if applicable.
d) Excise Duty if applicable.
e) Packing, forwarding and freight charges, if any.
f) Validity of quotation: 90 days.
13.
The supplier while submitting the quotation should invariably submit an Income-tax Clearance
Certificate.
14.
Consortium agreements and MOUs will not be considered.
15.
The Principal, JNTUA College of Engineering, Pulivendula reserves the right to assess the capacity /
capability of the suppliers in the overall interest of the institute without assigning any reason.
16.
The Principal, JNTUA College of Engineering, Pulivendula is not necessarily bound to accept the
lowest offer / bid.
17.
Payment will be made within the reasonable amount of time after the furniture is received in good
condition and within the stipulated time as per the specifications laid down and after the certification by
the Committee of JNTUA College of Engineering, Pulivendula.
18.
The furniture should be supplied within eight weeks from the date of issuing of purchase order.
19.
The institution reserves the right to place the orders for individual items with different tenders.
20.
The quantities indicated in the tender notifications are all subject to modification of the time of placing
orders.
21.
The company should have ISO 9001:2000 certification.
Sd/- PRINCIPAL
ABSTRACT OF SCHEDULE – E.1
Dept of Electrical and Electronics and Engineering
Simulation Lab
Schedule
No
Name of the Equipment
Quantity
E.1
Power System Software Packages
E1.a. Mi-Power
E1.b. PSCAD
5 Users
2 Users
Following page gives detailed specifications.
Estimated
Amount
500000=00
300000=00
EMD
Amount
10000=00
6000=00
ABSTRACT OF SCHEDULE – E.1
Dept of Electrical and Electronics and Engineering
Simulation Lab
Item: Power System Software Packages
A) MI POWER
B) PSCAD
E.1.a.MI POWER Software Specifications :( 5 Users)
A. Graphical User Interfaces

Power System Network Editor
Database Manager
Batch Mode Interface
MultiGraph Plotter
AutoCAD Interface
Free Programmable Blocks
Automatic Single Line Diagram Generator
Report Generator
A. Power LFA - Load Flow Analysis
Fast-DeCoupled option
Newton – Raphson option
Gauss – Seidel method option
Frequency dependent load flow
Contingency ranking
Present Worth Computation
Real & Reactive power optimization
Custom Reports
B. Power SCS - Short-Circuit Study
Multi-case / Multi islanding / Multi generation version
Motor contribution
Earthing and Zigzag transformer
Reactor Sizing
Loop & Radial systems
Traveling shunt fault
Custom Reports
C. Power TRS - Transient Stability Study
Unlimited disturbances
Motor Starting analysis
User defined Control system (AVR, SVC,
HVDC, ULTC)
IEEE PSS and Text + Graphical outputs
D. Power RCD - Relay Co-ordination
Automatic / Interactive / Manual Primary-back-up relay pairs generation
Phase and Earth relay co-ordination
Optimum setting for Motor relays
Extensive database of relays and fuse
Pick, drag and drop relay curves
Fault simulation and relay trip sequence
Export to AutoCAD
Optional inclusion of motor contribution during fault simulation
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
Economic Dispatch
Harmonic analysis
Long term demand forecast
Line and Cable parameter calculation
Sub-Synchronous Resonance
Voltage Instability Analysis
Dynamic stability study with
Network Reduction
Electro Magnetic Transient Stability (EMTP)
Ground Mat Design
K.
L.
M.
N.
O.
P.
Q.
R.
S.
T.
U.
V.
W.
X.
Y.
Z.
Three-phase Load Flow
Contingency analysis
Network reconfiguration (Express feeder)
Voltage regulator placement
Cost benefit analysis
Over current relay co-ordination
Long term load forecasting
Energy loss consumption
DTC relocation
Switching optimization
Cost estimation module
Line Re-conductoring
Short circuit studies
Cable parameter calculation
Line parameter calculation
DC-load flows
E.1.b. PSCAD Latest Version: [2 users]
 Component definitions cmp files
 Plot curves exported as CSV through clipboard into Excel or other data analysis
software
 Graphic elements to WMF/BMP through clipboard into MS word or equivalent
 Backward compatible files “save as” as to PACAD® V4.1,V4.0,V3 psl/psc files.
Note: backward compatibility is limited to the features available in the target
version.
EMTDCTM Output
 Common Transient Data Exchange (COMTRADE) IEEE-C37.111 is supported for years
1991 in both ASCII and BINARY (with some limitations)
 Output for time domain trace storage (ASCII)
 Output for frequency domain data storage (ASCII)
 Output for storage channel information (ASCII)
ABSTRACT OF SCHEDULE – E.2
Department of Electrical and Electronics Department
Electrical Machines Lab
Estimated Amount: Rs. 9,00,000=00
Schedule
No.
Name of the Equipment
E.2
1.
Electrical Machines Lab
Cylindrical rotor synchronous machine [AC Alternator Coupled
with DC Shunt Motor (5 H.P)]
Three winding Transformer Test Kit
Three Phase Squirrel cage induction motor [5 H.P] with star
connected type
D.C.Shunt Generator coupled with DC shunt motor [5 H.P]
identical set to conduct Hopkinson’s test
D.C Series Generator coupled with DC series motor [5 H.P]
identical set to conduct Load test on series generator
Three phase slip ring induction motor [5 H.P] with star
connected type with loading arrangement like break drum and
spring balances
DC compound motor [5 H.P] with break drum and spring
balances
Auxiliary DC shunt motor with a synchronous generator [5 H.P]
with synchronizing lamps [To conduct experiment of V and
Inverted V curves]
Single Phase Loading Rheostats
2.
3.
4.
5.
6.
7.
8.
9.
Quantity
1
2
1
1
1
1
1
1
2
Estimated Amount: Rs. 9,00,000=00
EMD Cost: Rs. 18,000=00
Following page gives detailed specifications
ABSTRACT OF SCHEDULE – E.2
Dept of Electrical and Electronics and Engineering
Electrical Machines Lab
SL. No
1.
2. A
NT CIRCUIT OF
Name of the item with specifications
Cylindrical rotor synchronous machine [AC Alternator
Coupled with DC Shunt motor (5 H.P)]
a) D.C.Shunt Motor (K.W.3.7, Volt 200, RPM.1500)
b) A.C.Generator (K.W 3.7, 3 phase, Volts:415, RPM.1500,
self excited type)
c) Class F type insulation, mounted on M.S Base frame&
Coupling, and also 3 point Starter, self-regulated in screen
protected drip-proof enclosure, Confirming to IS 4722
d) Metering Equipment
1. Ammeter – MI- 1– 5 A -1
2. Voltmeter -MI - 0 – 300 V-600 V -1
3. Wattmeter - LPF – 150 V/5A- 1
4. Wattmeter - UPF -300 V/2.5A – 1
THREE WINDING TRANSFORMER TEST KIT
a) PANEL DESCRIPTION:
TRANSFORMER SPECIFICATION : 2KVA
PRIMARY VOLTAGE
: 220V
SEC
: 110V,1KVA
TERTIARY
: 63.5V,1KVA
VARIAC;
: 12A
WATTMETER
: LPF\UPF (DIGITAL) 20A
VOLTMETER
:750V,AC - MI – 1NO
AMMETER
: 20A, AC - MI – 2NOS.
Quantity
One
Two
Necessary protection devices, push button & indicators are
provided.
3.
4.
b) Single phase Delta connected transformers[2 kVA]
Three phase squirrel cage induction motor [5 H.P] with
star connected type
a) Class F type insulation, Base Plate & Coupling and also
D.O.L Starter, self-regulated in screen protected drip-proof
enclosure, Confirming to IS 4722.
b) Metering Equipment
1. Ammeter – MI- 1– 5 A -1
2. Voltmeter -MI - 0 – 300 V-600 V -1
3. Wattmeter - LPF – 150 V/5A 1
4. Wattmeter - UPF -300 V/2.5A – 1
D.C Shunt Generator coupled with DC Shunt motor (5
H.P) identical set to conduct Hopkinson’s test
a) DC Shunt Motor (K.W 3.7 Volt220, R.P.M.1500)
b) D.C. Generator (K.W.3.7, Volt 200, RPM.1500)
c) Class F type insulation, mounted on M.S Base frame&
Coupling, and also 3 point Starter , self-regulated in screen
protected drip-proof enclosure, Confirming to IS 4722.
d) Metering Equipment
1 Voltmeter[ 0 – 600 V] -MC -1
2 Voltmeter[ 0 – 300 V]- MC -2
3 Ammeter [0 – 20 A] -MC -2
4 Ammeter [0 – 2 A] - MC -2
6 SPST knife switch - 1
One
One
5.
6.
7.
8.
D.C Series Generator coupled with DC Series motor (5
H.P) identical set to conduct Load test on series generator
a) DC Series Motor (K.W 3.7 Volt220, R.P.M.1500)
b) D.C Series Genetrator (K.W.3.7, Volt 200, RPM.1500)
c) Class F type insulation, mounted on M.S Base frame&
Coupling, and also 3 point Starter , self-regulated in screen
protected drip-proof enclosure, Confirming to IS 4722.
d) Metering Equipment
1. Voltmeter -0 – 300 V - MC -1
2. Ammeter- 0 – 10/20 A - MC -1
3. Loading Rheostat - 5 KW -1
Three phase slip ring induction motor [5 H.P] with star
connected type with loading arrangement like break drum
and spring balances
a) Class F type insulation, Base Plate & Coupling and also
Rotor resistance Starter, self-regulated in screen protected
drip-proof enclosure, Confirming to IS 4722.
b) Metering Equipment
1. Ammeter – MI- 1– 5 A -1
2. Voltmeter -MI - 0 – 300 V-600 V -1
3. Wattmeter - LPF – 150 V/5A 1
4. Wattmeter - UPF -300 V/2.5A – 1
DC Compound motor (5 H.P) with break drum and
spring balances
a) D.C. Compound Motor (K.W.3.7 Volts: 220V, R.P.M.1500)
b) Class F type insulation, Base Plate & Coupling and also
Four point Starter, self-regulated in screen protected dripproof enclosure, Confirming to IS 4722
c) Metering Equipment
1. Ammeter – MC- 1– 20 A -1
2. Voltmeter -MC - 0 – 300 V -1
3. Rheostat – 350 ohms, 1.2 A
4. Rheostat – 180 ohms, 2 A
Auxiliary DC Shunt motor with a synchronous generator
(5 H.P) with synchronizing lamps [To conduct experiment
of V and Inverted V curves]
a)DC Shunt Motor (K.W 3.7 Volt220, R.P.M.1500)
b) A.C.Generator (K.W 3.7, 3 phase, Volts:415, RPM.1500,
self excited type)
c)Class F type insulation, mounted on M.S Base frame&
Coupling, and also 3 point Starter , self-regulated in screen
protected drip-proof enclosure, Confirming to IS 4722.
c)radius of shaft is 2.5cm
d) Metering Equipment
1. Ammeter – MI- 1– 5 A -1
2. Voltmeter -MI - 0 – 300 V-600 V -1
3. Wattmeter - LPF – 150 V/5A- 1
4. Wattmeter - UPF -300 V/2.5A – 1
4. Synchronizing lamps – three one for each phase with
holders and house on base plate
One
One
One
One
9.
Single Phase Loading Rheostats
Current: 0 to 30A,
(With casing and 10 steps switching arrangement in steps of
1A, 10 steps switching arrangement in steps of 2A)
Two
ABSTRACT OF SCHEDULE E.3
Department of Electrical and Electronics Department
Power Electronics Lab
Estimated Amount: Rs. 2,95,000=00
Schedule
E.3
1.
2.
3.
4.
5.
Name of the Equipment
Quantity
Power Electronics Lab
Single Phase full controlled Bridge converter with R & RL
Loads
Single Phase dual converter with R Load and RL Loads
Single Phase bridge inverter with R Load and RL Loads
Single Phase half controlled bridge converter with R-Load
Notice Boards
[10*4 feets] Glass covered with lock inside wealvet cloth
2
2
2
2
5
Estimated Amount: Rs. 2,95,000=00
EMD Cost: Rs. 5,900=00
Following page gives detailed specifications
ABSTRACT OF SCHEDULE – E.3
Dept of Electrical and Electronics and Engineering
Power Electronics Lab
S. No
01.
Name Of The Equipment Wit Brief Specification
Single phase full controlled Bridge Converter With R and RL Loads
Quantity
a) 1 ph fully controlled bridge converter unit- 220V/5A: 25A/1200V devices provided with
suitable meters &MCB.
b) Single phase converter triggering unit.
Firing circuit: Single phase bridge converter firing circuit is based on timer oscillator,
pulse generator, pulse amplifier, pulse triggering method. Inverter frequency can be varied
from 25Hz to 250Hz. Two output pulses are taken across isolation pulse transformer to
trigger two SCRs of series inverter power circuit.
Power circuit: Power circuit section of the parallel converter consists of two inverter grade
SCR. Two fast recovery diodes, commutation split inductors, two commutation capacitors.
Each device is mounted on proper heat sink protected by fuse di/dt limiting inductor and
RC snubber components
Device ratings: 16A/1200V with Tq=20Us.
02.
Single Phase dual converter with R load and RL Loads
a) single phase dual converter power circuit 230V/5A, 1-phase isolation
transformer with tappings 230V/5A, R-load 150  /2A, L-load 0-50150mH/2A
b) Single phase dual converter firing unit
Two
Two
Firing circuit: Single phase bridge converter firing circuit is based on timer oscillator,
pulse generator, pulse amplifier, pulse triggering method. Inverter frequency can be varied
from 25Hz to 250Hz. Two output pulses are taken across isolation pulse transformer to
trigger two SCRs of series inverter power circuit.
Power circuit: Power circuit section of the parallel converter consists of two inverter grade
SCR. Two fast recovery diodes, commutation split inductors, two commutation capacitors.
Each device is mounted on proper heat sink protected by fuse di/dt limiting inductor and
RC snubber components
Device ratings: 16A/1200V with Tq=20Us.
03.
Single phase bridge inverter with R load and RL loads
a)1 phase MC murray bridge inverter with firing circuit – 30V/2A
1-pahse Mc Murray bed ford inverter with firing unit 30V/5A,
b) 1-phase parrall bridge inverter with firing circuit 30V/2A, R-load 50  /2A, Lload 0-50-150mH/2A
Two
Firing circuit: Single phase bridge inverter firing circuit is based on timer oscillator, pulse
generator, pulse amplifier, pulse triggering method. Inverter frequency can be varied from
25Hz to 250Hz. Two output pulses are taken across isolation pulse transformer to trigger
two SCRs of series inverter power circuit.
Power circuit: Power circuit section of the parallel inverter consists of two inverter grade
SCR. Two fast recovery diodes, commutation split inductors, two commutation capacitors.
Each device is mounted on proper heat sink protected by fuse di/dt limiting inductor and
RC snubber components
Device ratings: 16A/1200V with Tq=20Us..
04.
05.
Single phase half controlled bridge converter with R-load
a) Single phase Half Controlled Converter Power circuit 230V/5A,1ph
isolation transformer with tappings 230V/5A and R-Load with 150  /5A
b) Single phase converter firing unit
Notice boards
[10*4 feets] Glass covered with lock- inside wealvet cloth
Two
Five
ABSTRACT OF SCHEDULE – E.4
Department of Electrical and Electronics Department
Power Systems Lab
Estimated Amount: Rs. 4,85,000=00
Schedule
E.4
1.
2.
3.
4.
5.
Name of the Equipment
Quantity
Power Systems Lab
Characteristics of (IDMT) over current relay
[Electronomagnetic Type or Earth Fault with Testing kit Non
Directional Electromechanical Type] Test Kit
Characteristics of solid state negative phase sequence current
relay (DMT)-Test Kit
Numerical Over Voltage / Under Voltage Relay Test Kit
Characteristics of % Bias with differential relay testing kit
Electromagnetic type static type
Chairs Attached Planks
1
1
1
1
25
Estimated Amount: Rs. 4,85,000=00
EMD Cost: Rs. 9,700=00
Following page gives detailed specifications
SCHEDULE – E.4
Dept of Electrical and Electronics and Engineering
Power Systems Lab
S.No
Name Of The Equipment Wit Brief Specification
01.
CHARACTERISTICS OF (IDMT) OVER CURRENT RELAY
[ELECTROMAGNETIC TYPE OR EARTH FAULT WITH TESTING KIT
NON DIRECTIONAL ELECTROMECHANICAL TYPE]TEST KIT
Quantity
one
RELAY SPECIFICATION:
 C.T.SEC: 1A OR 5A
 NON- DIRECTIONAL
 PLUG SETTING: 50% - 200%
 TIME MULTIPLIER SETTING: 0.1 – 1 ,
 OUTPUT : 8A relay 1NO.
 Characteristics : 3sec-10times
 Auxiliary supply : Self powered / powered
 Construction : Draw out
Accuracy
 The relay conforms to error class index E 7.5 as per BS 142-1966 and 7.5 as
per IS 3231-1965, at ten times reference current setting.
 The relays comply fully with the requirements of IS 3231-1965 and are
suitable for use in normal tropical environments.
Input voltage : 220v ac , 50hz, 500va
Output current : output current continuous variable with range selection.
No of ranges 6 : 1A, 2A, 5A, 10A, 20A & 50A - selectable
Current injection : output current short switch provided for setting the output current
Burden : 3VA
Current output : pure sine wave technique
duty : Intermittent
Ammeter : 2A 3 ½ DIGIT DIGITAL
Range of experiments:
 Study of over current relay operation.
 Time characteristic.
 Time characteristic at different TMS
 To study of operating time.
 To Study of pick up current level.
 To Study drop off (reset level) current.
 Flag or target
 Study of draw out construction.
02.
CHARACTERISTICS OF SOLID STATE NEGATIVE PHASE SEQUENCE
CURRENT RELAY (DMT)– TEST KIT
RELAY SPECIFICATION:
C.T. SEC : 1A OR 5A
Negative Phase sequence current I2s= 10% or 20% or 30%
DMT : 3,6 & 9 sec.
OUTPUT : 0.5 second 7500VA with maximum of 30 amps and 660 volts, ac or dc.
Auxiliary supply : powered
Resetting voltage : 90% or more of the voltage setting.
Construction : Draw out
Accuracy
Reference conditions: Ambient temperature: 27 C ±2 C
Frequency: 50 Hz. –0.5%
Auxiliary voltage: Rated value
One
Accuracy under reference conditions: Pick-up error: ±10%
Time error at all settings: ±10%
Impulse voltage The relay complies with the requirements of IEC 255-5/IS
8686-1977/BS 142 Section 1.3.
Range of experiments:
Study of negative sequence relay operation.
DMT Time characteristic.
To study of operating time.
To Study of pick up level.
To Study drop off (reset level) voltage.
Flag or target
03.
NUMERICAL OVER VOLTAGE / UNDER VOLTAGE RELAY TEST KIT
i) Electromagnetic Type
ii) Microprocessor Type
RELAY SPECIFICATION:
P.T. SEC : 110VAC,220v, 415vac selectable
PLUG SETTING:
OV MODE: 105% to 180% of Vn in steps of 5%.
UV MODE: 95% to 20% of Vn in steps of 5%.
TIME MULTIPLIER SETTING: 0.1 – 1.6 in steps of 0.1
OUTPUT : 2 C/O ( self reset ) 2kva/240W (R)
Characteristics :
Normal Inverse 3.5 sec in O/U mode.
Normal Inverse 5.7sec in U/V mode.
Definite time 1,10,100secs.
Auxiliary supply : powered - 95v to 240v AC/DC
Resetting voltage :
90%-95% of set voltage Vs for Over voltage. .±5% of Vs.
For Under voltage ; 105% - 110% of set value.±5% of Vs.
Construction : Draw out
Accuracy
As per IS 3231:1987. Refer fig7 for details. The curve is given for Vn=110v. For
Vn=240 and Vn=415v it
is limited by over load capacity.
As per Error Class 5. IS3231:1987
Reset Time: Less than 50msec.
Over load capacity : Upto 800 volts.
Input voltage : 220v ac , 50hz,
Output Voltage : output voltage 0 - 660v continuous variable.
Capacity : 220VA
Duty : Continuous
Voltmeter : 200V AC, 3½ DIGIT DIGITAL
Time interval meter : Selectron 0.0001 sec accuracy. (auto range / manual range
programmable)
Protection Timer: Selectron 0-99sec digital.
Range of experiments:
Over voltage mode:
Study of over voltage relay operation.
Time characteristic. IDMT / DMT
Time characteristic at different TMS
To study of operating time.
To Study of pick up voltage level.
To Study drop off (reset level) voltage.
Flag or target
Study of % error.
Under voltage mode:
one
04.
05.
Study of under voltage relay operation.
Time characteristic IDMT / DMT
Time characteristic at different TMS
To study of operating time.
To Study of pick up voltage level.
To Study drop off (reset level) voltage.
Flag or target
Study of % error.
CHARACTERISTICS OF % BIAS WITH DIFFERENTIAL RELAY TESTING
KIT
ELECTROMAGNETIC TYPE
STATIC TYPE
SPECIFICATION:
This test set-up consists of the following
1. Static % differential relay –MBCH series
2. Relay set-up with meter
One no. of static % differential relay
Electricity board approved Relays
L&T,Alstom/,ashida/,ABB,/Siemens/Reyrolle.
CT secondary current:
1A or 5A
% Setting Range. 10% - 50% of in steps of 10% 2 biased inputs
Meters:
1. Two nos of 3 ½ digit ammeter - MECO to indicate current
2. Variable current source Two numbers
3. One no. of automatic relay tripping time measurement circuit.
4. One no. of micro controller based Time
5. Interval Meter LED display
6. One no of ON push button
7. One no. of Off /rest push button
8. Potential free Outputs NO & NC
9. Time Interval meter Internal / External selectable.
10. Built in Auxiliary power source.
11. Provision for RELAY ‘NO’ / ‘NC’ connection
Input voltage : 415v ac , 50hz, 3 Ph.
Output Voltage : output voltage 0 -415V
Duty : Continuous
Ammeter : 1Aac, 3½ DIGIT DIGITAL
CT : In build
Time interval meter : Selectron 0.0001 sec accuracy. (auto range / manual range
programmable)
Protection Timer : Selectron 0-99sec digital.
3 PH. MOTOR : 0.5HP
Rheostat : 1no.
Chairs Attached Planks
Back support height:2ft, MS pipe 1” hallow round pipe, Flat patti:17×2 mm (5 Supports)
Poly urethane moulded foam: Height:24”, Widhth:18.5”, Thickness :3.5”, Sound proof cloth
cover 7 mm thickness with double color,
Backside cover: PVC fiber 24” ×18.5” with suitable thickness
Back fix:4 bolts
Chair seat:
Frame: 18” ×18” with (40 mm ×20 mm)hollow tube on top of it 4 mm hard board with two
supports.
Poly urethane moulded foam seat : 18” ×18”, cushion thickness 2”.
Seat Fix: 16 gauge back brackets(Four bolts)
Sound proof cloth cover 7 mm thickness with double color. Plank of writing pad with suitable
suitable material like hard fiber/wood
One
25
ABSTRACT OF SCHEDULE – E.5
Department of Electronics and Communication Engineering
Schedule
E.5
Name of the Equipment
E5.a
E5.b
E5.c
E5.d
E5.e
XILINX (Latest Version) {10.1I}
FPGA Trainer Kits
CPLD Trainer Kits
Communication Simulink
[MAT LAB & Tool Boxes]
Digital Signal Processor Kits
Following page gives detailed specifications
Quantity
Estimated
EMD
25 Users
10 Nos
10 Nos
25 users
500000=00 10000=00
250000=00 5000=00
250000=00 5000=00
500000=00 10000=00
20 Nos
800000=00 16000=00
SCHEDULE – E.5
Dept of Electronics and Communications Engineering
E.5.a Xilinx ISE Package – Latest Version
(Combination of Xilinx Synthesis tool XST + Place & Route software for Xilinx)
25 User License
E.5.b. SPARTAN-II FPGA Module:
1. Xilinx’s SPARTRAN-II FPGA device XC2SXX –3 TQ144
2. Jumpers for selection of configuration mode
3. SPROM socket on which Xilinx 17xx series SPROM can be used
4. On board 2.5V & 3.3V for core and I/O voltage
5. I/O voltage can be vary from 0 to 3.3V for various I/O standards
6. LED indication on successful configuration of device
7. Probing facility i.e. all IOBs of the device are brought on connector
E.5.c. CPLD Module:
1.
2.
3.
4.
Xilinx’s CPLD Device XC95XX-15 PC84.
Additional PLCC 44Pins Socket for Programming PLCC 44 pin Device.
Probing Facility i.e. all device IOBs are brought on Connector.
The same Module can be used as CPLD Programmer for PLCC 84 & 44 Pin
Devices.
Downloading cable:
The downloading cable is used to interface the trainer to computer via parallel port for
downloading the design into target device.
Power Supply:
Power supply module with trainer is specially designed for 230Vac/50 Hz
E.5.D.COMMUNICATION SIMULINK
DESCRIPTION
LICENCES
MATLAB 7.12
Neural Network Toolbox 7.0.1
25
2
Fuzzy Logic Toolbox 2.2.13
2
Signal Processing Toolbox 6.15
5
DSP System Toolbox 8.0
5
Communications System Toolbox 5.0
5
Image Processing Toolbox 7.2
5
Simulink 7.7
2
Embedded Coder 6.0
2
E.5.e. DSP STARTER KIT (DSK) TMS320C6713 WITH CCS* DSP
STARTER KIT FOR THE TMS320C6713 HARDWARE FEATURES:
Texas Instrument’s TMS320C6713 DSP operating at 225 MHz
Embedded USBJTAG controller with plug and play drivers, USB cable
Included TL V320AIC codec
2M x 32 on board SDRAM 512K bytes of an board Flash ROM
3 Expansion Connectors (memory interface, peripheral interface and host port
interface) On board IEEE 1149. I JTAG connection for optional emulator debug.
Four 3.5 mm audio jacks(micro phone, line-in, speaker and line out) 4 user
definable LED’s and 4 position dip switch, user definable +5 Volt operation only,
Power supply included
Size : 8.25” X 4.5” (210 X 115 mm), 0.062 thick, 6 layers
Compatable with spectrum digital DSK wire wrap prototype card.
SOFTWARE FEATURES:
TMS 320C6713 DSK Specified Code Composer Studio
ABSTRACT OF SCHEDULE – E.6
Dept of Electronics and Communication Engineering
CRO
Schedule
No
E.6
Name of the Equipment
CRO
Following page gives detailed specifications
Quantity
30
Estimated
Amount
600000=00
EMD
Amount
12000=00
SCHEDULE – E.6
Dept of Electronics and Communications Engineering
CRO
S.No
01
02
03
Parameter
Bandwidth
Number of Channels
Operating Modes
04
Vertical Deflection (Y)
05
06
07
08
09
10
11
Y-magnification
Accuracy
Rise time
Input impedance
Input Coupling
Input Voltage (Max.)
Time Base(T) Coefficients
12
13
14
15
16
17
18
Hold OFF time
Saw tooth output
Trigger modes
Trigger Source
Trigger coupling
Slope
TV Sync
19
20
Z –modulation
Calibrator
21
22
23
Power
Operating condition
Accessories
24
Guarantee/Warranty
Description
30 MHz
2
Ch 1/Ch2/Ch1&2, alternate and Chopped modes,
Addition or difference ±Ch1, ±Ch2 (with invert switch for
both the channels), X-Y mode: same sensitivity in both
directions.
5mV/div to 20 V/div with at-least 12 calibrated steps in 12-5 sequence.
× 5 to 1 mV (DC to 10 MHz)
± 2% both of vertical and horizontal deflections
< 12 ns
1 MΩ in parallel with 25 pF
DC-AC-GND
400 V(DC + AC peak)
At-least 18 calibrated steps in 1-2-5 sequence 0.5μs/div
to 0.2 s/div. with ×10 to 20 ns/div, indication when
UNCAL
Variable control to 1:10
5 Vpp
Auto or variable level with indication.
Ch1, Ch2, Ext, Alternate, Line
AC, DC, line, High Frequency, Low frequency
Positive or Negative Slope
Active TV Sync Separator with TV-V, TV-H values marked
on Time Base
5V (TTL)
Square wave 0.2 V and 2 V, with ±1%, 1 kHz for probe
compensation
190 V – 250 V, 50Hz, 40 VA
0 – 45o C, 90% RH
Service and Operating manuals, TWO Switchable probes:
x1 – x10, 50 ohms termination, differential probe, and
carrying case.
Guarantee period of one year or two years of warranty
(in case of warranty 90% payment may be made at the
time of supply and remaining 10% will be paid after the
warranty period
ABSTRACT OF SCHEDULE – E.7
Dept of Electronics and Communication Engineering
MICROWAVE
Schedule
No
E.7
& OPTICAL COMMUNICATION LAB
Name of the Equipment
Microwave and Optical Communication Lab
Following page gives detailed specifications
Estimated
Amount
405000=00
EMD
Amount
8100=00
SCHEDULE – E.7
Dept of Electronics and Communications Engineering
MICROWAVE & OPTICAL COMMUNICATION LAB
Optical Fiber Trainer Kits with standard specifications for conducting the following
Experiments.
1. Characterization of LED. (At wave lengths 660nm & 850nm)
2. Characterization of Laser Diode.( At wave lengths 660nm & 850nm)
3. Intensity modulation of Laser output through an optical fiber.
4. Fiber Optical Digital link.
5. Measurement of NA.
6. Measurement of losses for Analog Optical link.
Optical Fiber Trainer (OFT) kit specifications:











Trainer Kit (transceiver)
Electrical Section: 12 (64Kbits/sec) channels, including one slot for 16-bit Marker, User
programmable two 8-bit frame markers in the alternate frame, Manchester Coding / Decoding,
Data Rate - 768 Kbits/sec, 1.5 Mbits/sec after Manchester coding, 2 Voice PCM channels, Alaw Voice coding.
Optical Section : LED Operating Wavelength - 850nm & 650nm, Detector – Si, PIN Photo
Diode, FWHM Spectral Width - 100nm, Fiber - 1000micron plastic Fiber( 1m & 3m length).
Other Features: Expansion ports, Programmable marker settings, Single & Double marker for
False marker study, Latch type data switches for ‘1’ or ‘0’ transmission, Provision for feeding
TTL thru’ these data switches & Complete functional block diagram showing different stages
with test points and BNC ports for all I/O operations should be available.
Phone handsets for Voice communication
Plastic fibers of various lengths (up to 3 m.)
I/O ports to interface user built circuitry with the trainer
I/O BNCs to observe/measure and feed-in signals
Accessories
o NA measurement unit
o Fiber aligning unit
o EMI generation unit
o Expansion port cables for external circuit interface
o Special electrical patch cords to interconnect blocks, setup electrical copper link etc.,
Power supply unit with AC input varying from 190 V – 250 V
Service and User manuals
Guarantee/Warranty
Guarantee period of one year or two years of warranty
(in case of warranty 90% payment may be made at the
time of supply and remaining 10% will be paid after the
warranty period
1.
GUNN DIODE BASED MICROWAVE BENCH SPECIFICATIONS
(X-BAND: 8.2 GHz – 12.4 GHz)
1
GUNN Oscillator
GUNN Power supply
PIN Modulator
SPECIFICATIONS OF GUNN POWER SUPPLY:
Gunn bias voltage - 0.5 to 12 V
Current - 0 to 1.5A (Max)
Regulation - 0.2%for +10% Mains
Ripple - 2mv (rms)
Type of modulation - internal as well as
by using PIN Modulator
Modulation amplitude - 0 to 15V peak to peak
Output connector - BNC (F) for both gunn bias
& PIN modulator
Mains - 230V, 50Hz, 115 WATT approx.
Isolator
Direct Measuring Frequency Meter
Variable Attenuator (0-30 db)
Slotted Section with tunable detector
Detector Mount
VSWR Meter
SPECIFICATIONS FOR VSWR METER:
Amplifier Type - High gain tuned at one frequency
2 Sets
Frequency
1000Hz
Sensitivity - 0.1microvolt at 200
ohms for full scale
Band width - 25 to 30 Hz
Range - 60 db min in 10 db scale
Accuracy - 0.15 db on one range
Meter Linearity - 1% of Full scale
Scale-selector - Normal, Expander
Gain control - coarse & fine
Input - BNC (F,) 20000hms impendence
Input selector - Crystal, (4.5 ma) and
high (8.75 ma)
Mains Power - 230V, 50hz
Tunable Probe
Movable Short
Matched Termination
S S Tuner
Wave Guide Stand-5 no.
Cooling Fan
BNC Cable-2 No.
TNC Cable
Guarantee/Warranty
Guarantee period of one year or two years of
warranty
(in case of warranty 90% payment may be made at the
time of supply and remaining 10% will be paid after
the warranty period
2. Reflex klystron BASED MICROWAVE BENCH SPECIFICATIONS
(X-BAND: 8.2 GHz – 12.4 GHz)
2
Klystron Mount
Klystron Power supply
Klystron tube
SPECIFICATIONS FOR REFLEX KLYSTRON POWER
SUPPLY:
Beam voltage-220 to 450v
Beam current-50
Operating voltage-300V (approx.)
Reppler supply-5 t0 250V (negative W.R.T cathode)
Modulation:- internal square wave 500 to 2500Hz
with variable frequency & amplitude, saw tooth
wave
150-300hz variable frequency & amplitude.
Mains-230v, 50 Hz, 115 watts approx
Isolator
Direct Measuring Frequency Meter
Variable Attenuator (0-30db)
Detector Mount
Mechanical Turn Table
Standard Gain Horn
E Plane Bend
H Plane Bend
VSWR Meter
SPECIFICATIONS FOR VSWR METER:
Amplifier Type - High gain tuned at one frequency
Frequency - 1000Hz
Sensitivity - 0.1microvolt at 200
ohms for full scale
Band width - 25 to 30 Hz
Range - 60 db min in 10 db scale
Accuracy - 0.15 db on one range
Meter Linearity - 1% of Full scale
Scale-selector - Normal, Expander
Gain control - coarse & fine
Input - BNC (F,) 20000hms impendence
Input selector - Crystal, (4.5 ma) and
high (8.75 ma)
Mains Power - 230V, 50hz
Cooling Fan
Pickup Horn
Slotted Antenna-Broad Wall
Slotted Antenna-Narrow Wall
Dielectric Antena
E- Sectorial Horn
H-Sectorial Horn
Parabolic Disc
Pyramidal Horn
BNC Cable
Fasterners
Wave Guide Stand-5 No.
Guarantee/Warranty
2 Sets
Guarantee period of one year or two years of warranty
(in case of warranty 90% payment may be made at the time of supply and
remaining 10% will be paid after the warranty period
3. Reflex klystron BASED MICROWAVE BENCH SPECIFICATIONS
(X-BAND: 8.2 GHz – 12.4 GHz)
3
KLYSTRON MOUNT
Klystron tube
KLYSTRON POWER SUPPLY
SPECIFICATIONS FOR REFLEX KLYSTRON POWER
SUPPLY:
Beam voltage-220 to 450v
Beam current-50
Operating voltage-300V (approx.)
Reppler supply-5 t0 250V (negative W.R.T cathode)
Modulation:- internal square wave 500 to 2500Hz
with variable frequency & amplitude, saw tooth
Wave 150-300hz variable frequency & amplitude.
Mains-230v, 50 Hz, 115 watts approx
Isolator
Direct Measuring Frequency Meter (DRF)
Variable Attenuator (0-30 db)
Slotted Section with tunable detector
Tunable Probe
Detector Mount
Movable Short
Matched Termination
Waveguide Stand
VSWR
SPECIFICATIONS FOR VSWR METER:
Amplifier Type - High gain tuned at one frequency
Frequency - 1000Hz
Sensitivity - 0.1microvolt at 200
ohms for full scale
Band width - 25 to 30 Hz
Range - 60 db min in 10 db scale
Accuracy - 0.15 db on one range
Meter Linearity - 1% of Full scale
Scale-selector - Normal, Expander
Gain control - coarse & fine
Input - BNC (F,) 20000hms impendence
Input selector - Crystal, (4.5 ma) and
high (8.75 ma)
Mains Power - 230V, 50hz
Cooling Fan
Fixed Attenuator:3db
Fixed Attenuator:6db
Fixed Attenuator 10 db
Variable Att.20db
E-Plane Tee
H-Plane Tee
Magic Tee
M.H.D Coupler:3db
MHD coupler 10db
M.H.D Coupler:20 db
C.D.Coupler:20db
T. Circulator
Y . Circulator
1 Set
BNC Cable
Fastners
Guarantee/Warranty Guarantee period of one year or two years of warranty
(in case of warranty 90% payment may be made at the time
of supply and remaining 10% will be paid after the warranty
period
ABSTRACT OF SCHEDULE – E.8
Dept of Bio-Technology
PLANT TISSUE CULTURE LAB
Schedule
No
E.8
E.8.a
E.8.b
E.8.c
E.8.d
E.8.e
E.8.f
E.8.g
E.8.h
E.8.i
E.8.j
E.8.k
E.8.l
E.8.m
E.8.n
Name of the Equipment
Estimated
Amount
EMD
Amount
Plant Tissue Culture Lab
Laminar airflow
Autoclave
Electronic Weighing Balance
Compound Microscope
Double Distillation Unit
Digital Ph Meter
Hot air oven
Green house facility
Refrigerator
Culture racks
Cooling centrifuge
Shaker incubator
Plant metabolite Extractor (soxillate)
Digital camera for explants documentation
Following page gives detailed specifications
60000=00
30000=00
23000=00
12000=00
53000=00
15000=00
40000=00
21000=00
40000=00
30000=00
70000=00
28000=00
20000=00
25000=00
1200=00
600=00
460=00
240=00
1060=00
300=00
800=00
420=00
800=00
600=00
1400=00
560=00
400=00
500=00
SCHEDULE – E.8
Dept of Bio-Technology
PLANT TISSUE CULTURE LAB
E.8.a. LAMINAR AIR FLOW
 Type – Horizontal
 HEPA of 0.3µ of an efficiency of 99.97% down to 0.3µ media is of glass fiber & made of
pleats back & frown in an anodized Aluminum frame.
 Pre filter of dry fiber washable type with the frame of on all the sides.
 Statically Balanced motor blower Assembly (Heavy Duty)
 Air Velocity - Between 0.4 to 0.5 mls +-20%
Noise level is very low
Vibration is also very low.
 Normal working fluorescent Light.
 Static pressure Manometer
 In U. V. Light 1 x 30/15 watts.
 Front Door of Acrylic Sheet (Transparent)
 Gas cock/ Burner

Working Area Size

2’x2’x2’ Mild Steel Body
Optional Accessories: U.V resistant poly carbonate sheet in place of Acrylic sheet
2’X2’X2’
E.8.b. AUTOCLAVE











Type – Horizontal
Capacity – interior chamber of the unit - 200L
Double walled with inner chamber made of stainless steel outer made of mild steel duly
painted.
Pressure Range : 0-20 P.S.I / 0-30 P.S.I
AUTOMATIC PRESSURE CONTROL SWITCH
Electrically Heated Lid with easy paddle lifting arrangement.
Lid is made of thick stainless steel plate controls the pressure.
pressure release valve drain safety valve,
water level indicator
Neoprene rubber gasket joints less.
Supplied with stainless steel basket plug and cord to work on 220V AC supply HZ.
CHAMBER SIZE: LOAD:
350X550MM 14”X22” 2KW (Inner Stain less steel & Outer Mild steel)
E.8.c.ELECTRONIC WEIGHING BALANCE
 Type – Analytical/ Laboratory
 Capacity – 220 grams
 Sensitivity- 0.001gm
 Calibration – Fully automatic, 100% accuracy
 Power supply – 2 way AC adapter and rechargeable battery
 High contrast, large backlight LCD display
 Wind break shield with lid
 Level indication gauge and adjustable leveling screws
 Pan – large silky stainless steel, detachable for easy maintenance
 Other standard features and accessories etc.
E.8.d. COMPOUND MICROSCOPE
 Magnification 100 x – 600 x
 standard set complete with two eyepieces H 10x and 15x,
 Hard anti-reflection coated colour parfocal archromat Objectives 10x and 40x,
 360° rotating head with one 30° inclined eyepiece and one vertical eyepeice with diopter
 Built-in sub stage fixed condensers with iris diaphragm,
 Pain square stage (100 x 100mm) with two clips
 Plano-concave mirror in adjustable fork mount
 20-watt, 12-volt extra-bright halogen illumination with a variable rheostat for precise lighting
control
E.8.e.DOUBLE DISTILLATION UNIT
 Model-Automatic Cabinet Water Still 2D (Borosilicate Glass).
 Out Put 4 Ltrs/Hr.
 Distillate quality – Pyrogen free
 Minimum pressure – 3 p.s.i
 Conductivity - 0.8µS/cm
E.8.f. DIGITAL pH-METER






Range
- 0.0 to 14.0
Accuracy - +/- 0.01
Type
- water proof design
Resolution - 0.01 pH
Display
- 3 ½ Digit LED Display
Accessories Glass Electrode, Electrode Stand, Dust Covers, Buffer Solutions & Instruction
Manual
E.8.g. HOT-AIR-OVEN
 Triple walled in construction with inner made of stainless steel-304 and exterior of G.I./ M.S
sheet duly finished in grey powder coated shade.
 Temperature Range: 5: - above ambient to 250o C.
 Temperature Accuracy: +/- 1o C.
 Size: 14” x 14” x 14”
 Capacity: CFT 1.6 Lit 45, Watts 1500.
 Digital Controller
E.8.h. GREEN HOUSE FACILITY

Green house Net
Length: 16 Feet
Width: 20Feet
Height: 16Feet
E.8.i. REFRIGERATOR









320Lit,
Double door with freezer
Compartment temperature range 1oC to 4oC
Freezer temperature range -1oC to -20oC
Temperature stability ± 3oC
Automatic defrost
Compartment lights
Full size adjustable shelves
Other standard accessories: mounting stand, Voltage stabilizer.
E.8.j. CULTURE RACKS
 Length - 4 Feet
 Height- 6 Feet
 Width- 1.5 Feet
 5 Shelves
 4 tube lights for each shelves
E.8.k. COOLING CENTRIFUGE



Temperature range: 40C
R-244 Angle Head (With Polypropylene Tubes) Size: 12 x 15ml
R-248 Angle Head (with Polypropylene Tubes) Size: 24x1.5ml

Voltage Stabilizer: Input: 170Volts to 260Volts,
Output: 220-240Volts
E.8.l. SHAKER INCUBATOR








Chamber Volume : 180 Liter
Max Shaking Capacity: 9 Liter.
Approx External Dimension: Width 70 x Depth 78 x Height 125.
Temperature Range: 5oC to 60 oC.
Control speed form 20 to 250 RPM along with universal platform (without flask holding
clamps)
500ml x 16 flasks
Voltage Stabilizer Model: Input: 170Volts to 260Volts, output; 220-240 Volts
Clamsps for holding conical flacks: Capacity 500ml
E.8.m. PLANT METABOLITE EXTRACTER (SOXILATE)
 Capacity: 1000ml,
 Flasks: 6,
 1800watts
E.8.n. DIGITAL CAMERA FOR EXPLANTS DOCUMENTATION
 Resolution -16 megapixel
 10X zoom
 Optical zoom – yes
 Digital zoom – yes
 LCD display
 Video function
 LCD size -3inches
 USB - USB 2.0 Hi-Speed
ABSTRACT OF SCHEDULE – E.9
Dept of Bio-Technology
Microbiology Laboratory
Schedule
No.
E.9
E.9.a
E.9.b
E.9.c
E.9.d
E.9.e
E.9.f
Name of the Equipment
Microbiology Laboratory
Floroscent Spectrophotometer
Gel Doc
Millipore Water purifier
Micro pippets
Ultra centrifuge
TDS conductivity meter
Following page gives detailed specifications
Quantity
Estimated
Amount
EMD
Amount
01
01
01
20 Nos
01
01
500000=00
300000=00
600000=00
200000=00
500000=00
30000=00
10000=00
6000=00
12000=00
4000=00
10000=00
600=00
SCHEDULE – E.9
Dept of Bio-Technology
E.9.a. Fluorescence Spectrophotometer
PC
controlled
Fluorescence
Spectrophotometer
(220
V)
capable
of
measuring
Fluorescence, Phosphorescence, Chemiluminescence and Bioluminescence with the following
technical specifications should be quoted:
S.No Parameter
Description
1
Light Source
2
Measuring Wavelength
3
4
Optical System
Sensitivity
5
6
7
Spectral Bandpass
Resolution
Minimum sample volume
8
9
10
Wavelength accuracy
Wavelength Scan Speed
Data Collection Rate
11
12
Filter System
Detector
13
Working temperature
14
15
Power Compliance
Software
16
Cell
17
18
Micro Cell
Cell Holder
19
Peltier Capabilities
20
PC / Printer
21
22
UPS
Optional accessories
Software controlled Polarized light generated using an Ozone
free Xenon Lamp
200 – 900 nm (Excitation and 200 – 900 nm (Emission) or
better, Zero Order Settable.
Monochromator with advanced grating
S/N Ratio of 800:1 or better (RMS) using Raman band of
water
variable / adjustable
± 2 nm (Minimum)
0.6mL (in use of standard 10mm rectangular cell)
± 1.5 nm or better
0.01 – 24000 nm/min
At least 80 data points/sec for fluorescence mode
measurements
Should comprise of software selectable emission filters
Photomultiplier Detector with support for the range 200 – 900
nm / High Performance PMT
15 to 35 ,45 to 80% (condensation not allowed, 70% or less at
35 or higher)
230 Volts, 50Hz
Compatible with Windows Vista, Windows XP, Windows
7 etc. should have various data analysis facilities like
arithmetic functions, smoothing, First to fourth
order
derivatives, area peak, normalization, merger difference
interpolate and Specific application
Programs should also be provided for determination of
phosphorescence,
simple
quantitation
and
kinetic
evaluations, GLP compliant.
One pair of standard 10 mm quartz cell with PTFE lid – 10X10
mm path length
10 mm length quartz micro cells
Peltier controlled One and Four 10 mm cuvette holding capacity
& magnetically stirred cell holder
Supplied through instrument manufacturer only software
controlled Temperature range 0 to 100º C (Min.) with
temperature stability ± 0.5º C (Max.)
Branded, to be supplied with the instrument with operating
system on CD and Microsoft Office Pro as well as licensed
latest antivirus programme. Printer compatible with Windows
Vista, Windows XP, Windows 7 etc.
An instrument compatible UPS to be provided with the system
Any other accessory useful for handling different types of
samples (such as Film/Powder and film, Kindly specify
details and use)
E.9.b. GEL DOC (GEL DOCUMENTATION SYSTEM)
The Gel Documentation system is a compact system for acquiring gel photographs and can be easily
accommodated in any part of the laboratory. The system should be able to image fluorescent DNA,
RNA, protein gels and calorimetric gels.
S.No Parameter
Description
Camera
1
2
Camera Resolution
Pixel array.
3
Pixel Density
4
Pixel Size
5
Lens
Illumination
7
Fluorescence
8
White Light
9
Epi-UV
Filters
10
Mounting
11
Type
12
Included with System
13
Optional
14
Custom filters
1.44 mega pixel resolution
1360x1024
12-16 Bit
4.6× 4.6 micron
Motorized and automated 6x zoom, 8 - 48 mm, f1.2 – closed
UV Trans-illumination, standard
White Light conversion screen, optional
254nm, 306, 370nm, optional
Motorized 6 position wheel - "drop in" filter design
Optical Band Pass, 52 mm
590 nm (Ethidium bromide, Ruby Red, Texas Red, Ruby
Orange)
435 nm (DAPI, STYO Blue), 535 (SYBR Green, SYBR
Gold, Fluorescein, Rhodamine, Eosin, Acrydine OrangeDNA), 570 nm (Pyronin Y), 670 nm (Acrydine OrangeRNA)
Inquire
Instrument
15
Overall dimensions(in)
54.6 x 42.67 x 83.8 cm (l x w x h)
16
Mass - camera unit
12.7 kg
17
Mass - Cabinet
44.4 kg
18
Power
120v or 240v
Computer Interface
IEEE 1394 6-pin 400 speed (FIREWIRE) PC and Macintosh
compatible, Serial connection (PC), and Serial to USB for
Macintosh
Performance Specifications
19
Resolution
34 micron/pixel at full zoom
20
Field of View
Supports up to 24.5 x 33 cm
21
Dynamic Range
>3.4 orders of magnitude
22
Data Acquisition
14-bit file accumulations
23
Binning Options
none
24
Detection Modes
Fluorescence
White light
Software
25
Analysis software
Molecular Imaging Software
26
Capture software
Molecular Imaging Software
Exposure Modes
27
Standard exposure
0.001 – 16 sec per exposure, up to 32 accumulations
28
Time lapse exposure
0.01 – 16 sec per exposure, minimum interval = 5 sec
E.9.c MILLIPORE WATER PURIFIER SYSTEM
System should be capable of producing type II (10-15Megaohm resistivity ) with pretreatment cartridge,
Reverse Osmosis, Electro Deionization,with feed water acceptance upto 2000micro Siemens c conductivity ,
Fouling Index (SDI) < 12, Total Chlorine < 3 ppm.
STAGE 1
2 Stage pretreatment system
PREFILTER
5 micron and 1 micron wrapped type depth filter
Less than 50 Db noise levels
Automatic low/high pressure cut off
DC pump with 0-2 pressure at 120L /hr
Inlet screen filter to DC pump
Operating weight 10.5 kg
Optional filters : 0.5 micron
SDI 50, TDS upt0 5000
STAGE 2
Pretreatment cartridge with anti scaling compound
Pump with unique temperature feedback mechanism
High flux Thin film composite polyamide RO membrane
rejection
with 94- 99%
Recirculation loop with capillary tube and diaphragm valve
Mixed bed ion electro deionization module with auto regeneration by a weak
electric current, eliminating the need for chemical regeneration or replacement
of DI resin cartridges .
EDI (Electro deionization) module that should not require softening pretreatment.
Carbon beads at cathode of the EDI module to prevent scaling of the module
Permeate divert valve which will divert low quality water to the drain.
Coaxial resistivity cell with a flow through design and a cell constant of
0.01cm-1
Display both compensated and non-compensated temperature accurate within
±0.1°C.
Type II Water flow rate @ 3 l/hr
STAGE 3
A cylindrical reservoir with a 50 liter capacity
Labclose mode
The system should have lab close mode option by which the system
automatically recalculates and maintains the quality of water daily even if the
system is not operated for 2 months
RFID TAG
The consumables should have RFID tag and detector in order to prevent
duplicate consumables and maintain traceability adhering to GLP norms
PRINTER
The Dispensing arm should have RS 232 port for taking printout directly from
COMPATABILITY dispensing POD
COMPUTER
COMPATIBIL-ITY
The system should be compatible with computer system for data
accesing.System history reports can be downloaded to a computer for storage or
to print out hard copy
CE,cUL,FCC
ceritified
The system should ensure efficiency and safety of operation ,the system is
certified for safety and electromagnetic compatibility
The system is designed to meet or exceed requirements as described by ISO
ISO
3696,ASTM 3696 ( Grade 2 Water) : ASTM D1193 ( Type II resistivity and TOC table 1
D1193
Specifications ) .
Pure (Type II) water:
TOC (ppb) …………………………………………….< 30
Flow rate ……………………………………………… 3 L/hr
Resistivity…………………………………………10- 15 Mega Ohms
E.9.d.MICRO PIPETTES
Light Spring forces reduced radically symptoms of RSI. The smooth and steady
1
pipetting action ensures more accurate and precise results
Soft Touch Tip Ejector
2
Patented gearing mechanism to lower the tip ejection forces, especially beneficial
3
when ejecting
tips with multichannel pipette
4
Easy to open for quick in lab service.
5
Adjustable finger rest: adjustable 120 degrees enables optimal position for
ejecting
the tips for best ergonomics, user can relax the pipetting hand between
6
pipetting cycles
Antimicrobial surface-Handle has antimicrobial treatment to avoid contamination.
7
Pipetting hat-when pipetting the hat rotates freely to prevent accidental volume
8
alteration
Advance Volume Gearing Mechanism - AVG
9
Self Supportive modular volume adjustment mechanism is separated from the
pipette hull therefore enhancing precision and accuracy and durability of the whole
10
mechanism
Precision click volume adjustment enabling 50 precision clicks per revolution
11
enabling 0.1ul steps
12
13
14
RANGE:
Adjustment mechanism is thermally isolated from the pipette hull to eradicate
hand warmth effect.
Enhance display resolution-big clear white and black display
Super blow-out
1) 0.2-20µl,
2) 1-10 µl
3) 10-100 µl
4) 100-1000 µl
E.9.e. ULTRA CENTRIFUGE
1
The Centrifuge should have a feature to install and remove rotor without tool in less
than 5 seconds with just a push of a button for quick and easy change of rotors for
different applications
It must be able to display both air/chamber temperature as well as temperature in the
2
sample
Dual Timer mode- At Start and at Speed
3
It must have an option for automatic lid opening at the end of the run
4
It must have capability of password protection for the programs.
5
It must have capability of password protection for lid opening
6
Temp. Range : -100C to 400C
7
Max. Capacity: 4 x 750ml
8
It must be able to display set parameters together with actual values, and parameters
9
must be readable at a distance of at least 5 meters
It must be UL listed, CSA Certified, CE Marked, IVD Complaint, Certified Bio safety,
10
WEEE, RoHS
The angle rotors must be manufactured from a highly corrosion and fatigue resistant
11
Carbon Fiber material. The Fixed Angle Carbon Fiber rotors should be warranted for
at least 12 to 15 years
It must be supplied with Fixed Angle Rotor capable of running a minimum of
12
48 x 2 ml micro tubes at speeds of at least 15200 RPM, 25314 x g.
It must be supplied with one more fixed angle rotor 6 x 100 ml, with 50ml and 15ml
13
adapters for round bottom tubes.
E.9.f. TDS CONDUCTIVITY METER
S.no
Parameter
Description
1
TDS Range
0 - 9990 ppm (mg/L)
2
Temp. Range
0 - 80 degrees Celsius
3
Resolution
1ppm, 1 degree Celsius (also available in 10 ppm)
4
Accuracy
+/- 2%
5
Conversion Factor
NaCl (avg. 0.5)
6
ATC
7
Power source
Built-in
sensor
for
Automatic
Temperature
Compensation of 1 to 50 degrees Celsius (33 to 122
degrees Fahrenheit)
2 x 1.5V button cell batteries (included) (357A)
8
Battery life
1000 hours of usage
9
Dimensions
15.5 x 3.1 x 2.3cm (6.1 x 1.25 x 1 inches)
10
Weight with case
76.5g (2.7 oz)
11
Weight without case
56.7g (2 oz)
ABSTRACT OF SCHEDULE – E.10
Dept of Computer Science and Engineering
Microsoft Office Software
Schedule
No
E.10
Name of the Equipment
Microsoft Office Software
Quantity
30 user licenses
Following page gives detailed specifications
Estimated
Amount
150000=00
EMD
Amount
3000=00
SCHEDULE – E.10
Dept of Computer Science and Engineering
Microsoft Office Software
S.No
1
2
3
4
5
6
Item
Edition
License Type
Quantity
Compatibility
Media Kit
Price
Specifications
Professional Edition of Latest version
Perpetual License
30 User Licenses
Should be compatible with Window XP and Windows 7
Yes
Inclusive of all taxes and should include Postal charges for
Media Kit
ABSTRACT OF SCHEDULE – E.11
Dept of Chemistry
Schedule
No
E.11
Name of the Equipment
INFRARED
SPECTROMETER (FTIR)
Quantity
01
Following page gives detailed specifications
Estimated
Amount
1000000=00
EMD
Amount
20000=00
SCHEDULE – E.11
Dept of Chemistry
INFRARED SPECTROMETER (FTIR) – 1 No
1. Optical performance
Wavelength Range
Spectral Resolution
Wavelength Precision
Wavelength Accuracy
Signal-to-Noise
2. Optical System
General
Interferometer
Optics
Detectors
Source
Beam splitter
Desiccant
Validation
Optical Windows
3. Data System
Signal sampling
Connectivity/Ports
Accessory recognition
Error Trapping
Component Checks
Power save mode
Operating Range
Typical desiccant lifetime
7,000– 350 Cm-1 optimized, proprietary KBr beam splitter
5100-550 Cm-1 with ZnSe optics
0.5 cm-1 standard
0.01 cm-1 at 3000 cm-1
0.05 cm-1 at 3000 cm-1
9,300:1 peak-peak, 5 seconds
32,000:1 peak-peak, 1 minute
14,500:1 peak-peak, 5 seconds
50,000:1 peak-peak, 1 minute
with optional performance pack
Field proven, rugged opto mechanical system with outstanding
performance and reproducibility, even in humid and tropical
environment, Vibration isolated base plate
High stability Rotary Michelson interferometer and, selfcompensating for dynamic alignment changes due to a tilt and shear
Kinematically mounted, zero alignment optics , with high
reflectivity and a low-angle off axis design. Proprietary Optics
Guard system for extended desiccant life and additional optical
component protection.
High linearity room temperature detector (standard).
Long-life source with proprietary hot-spot stabilization. User
replaceable from outside instrument
Proprietary extended range KBr
Long-life desiccant system accepts disposable packs. Software
controlled desiccant status indicator
Software controlled validation wheel option containing a
polystyrene reference material, traceable to a NIST
standard for wave number accuracy and a Schott NG11 filter for
ordinate repeatability (Optional)
KBr (standard), ZnSe option for exceptionally high humidity
environments
Over-sampling delta-sigma converter
USB, wireless and TCP/IP interface allows direct connection with
PC/LAN
Accessories to be automatically detected by the software as soon as
they are locked into the sampling area. Instrument parameters are
optimized for the installed accessory. Accessories information
stored with spectral data
All sample spectra are checked for common spectroscopic and
sampling problems.
Individual component checks under software control can be
executed on-demand or automatically scheduled at preset
times/intervals
Instrument standby and power-up can be automatically scheduled
15 – 350 C
5 years at 250 C and 90% relative humidity
4. Software and data
interpretation
General
Software
Sample Table
Reports
Processing
Scanalyse
Materials testing
Quantitative analysis
User training
Computer and printer
Accessories
A single software platform incorporates all of the functions required
for infrared analyses; instrument control, data manipulation and
analysis, and flexible report utilities. A suite of optional software
packages provide advanced capabilities or functions designed for
specific application areas. Optional Spectrum Touch functionality
optimised for touchscreen operation allows simple user interface for
turnkey operation with selected applications.
Multi-language software guiding users through every step of
operation with color coded alerts making it easy to see whether
samples meet specifications
Increases productivity by enabling multiple samples to be defined in
batches facilitating continuous operation
Quick print facility for graphs, spectra and results windows. Send to
Word functions for simple formatting via Microsoft Word
1st – 4th derivative with a variable filter, smooth (Savitsky-Golay,
moving average and triangular), difference, normalization, A, %T,
%R, KM, LOG (1/R), ordinate modes, cm-1, nm and micron
abscissa modes, +,-,*,/, difference, baseline correction, smooth,
deconvolution, normalize, interpolate, blank, Kramers-Kronig, ATR
correction, peak table, peak height and peak area.
Enables real time update of spectral information plus results to
provide faster feedback of information data status
Spectral comparison algorithm and Euclidean searching. Spectral
searching against commercially available or customer-developed
libraries
Single frequency, method development software. Spectrum includes
Beer’s Law, and chemometrics-based quantitative prediction
Provide training after the installation including instrument handling,
software operation with the packages environment.
Instrument has to connectivity with system and printer for data
purpose (Optional)
Other related accessories as per the specification
ABSTRACT OF SCHEDULE –E.12
DEPARTMENT OF CHEMISTRY
Schedule
Name of the Item
No
Gas Chromatography
E. 12
Following gives detailed specifications
Quantity
01
Estimated
Amount
EMD
Amount
1050000=00 21000=00
SCHEDULE –E.12
DEPARTMENT OF CHEMISTRY
TENDER SPECIFICATIONS FOR THE SUPPLY, DELIVERY, INSTALLATION OF
GAS CHROMATOGRAPHY -1No
Specifications for Gas Chromatograph with Manual injector, FID, ECD and TCD detectors
Requirement: One Number
System Capabilities:
Supports simultaneously: Two inlets, - Three detectors (third detector as TCD), and four detector
signals. The Gas Chromatograph must be a microprocessor controlled, dual channel with extensive
self-diagnostics and programmable pneumatic controls (EPCs) which can be operated by an external
PC through chromatography software besides meeting the other specifications as follows:
Column Oven: GLC oven should have been calibrated by NABL / ISO 17025-2005 accredited
laboratory
Operating temp. range: Ambient to temperature + 4.0 0 C to 4500 C
Temperature set resolution: should be 0.10C
Maximum achievable Temperature ramp rates is about 120 °C/min
Cooling rate: 4500 C to ambient in 4 minutes
Oven ramps: Oven must support 18 oven ramps wit 19 plateaus or more, negative ramps should be
allowed.
Oven cool down (22 °C ambient) 450 to 50 °C in 4.0 min
Column overheat protection: user defined up to 450° C
Electronic pneumatic controls for inlets and detectors:
Pneumatics must be electronic and programmable. Each EPC unit is optimized for its intended use
with a specific inlets and detector option.
Inlet pneumatics: Inlet must have electronic pneumatic control of carrier, split and septum purge gas,
including electronic ON/OFF
Pressure set point precision: Pressure set points must be able to be adjusted by increments of
0.001psi, with typical control + 0.001 for the range of 0.000 to 99.999 psi
Pressure/flow ramps: user must be able to set up to a maximum of three pressure/flow ramps in
addition to injecting at a different (pulsed) pressure.
Inlets
Type: capillary column injection port.
Inlet must allow option of modes of functing of split, splitless mode, - Pressure-pulsed split/splitless
mode
Pressure sensor accuracy: must have + 2% full scale pressure accuracy or better.
Flow sensor accuracy: must have a minimum of + 5% accuracy with + 0.5% repeatability.
Temperature range: ambient to 450 0C
Maintenance: Inlet sealing system is built in standard with each S/SL inlet for quick, easy, injector
liner changes for quick maintenance.
Detectors:
FID (Flame Ionization Detector)
Minimum detect ability: must have a minimum detect ability of 1.6 pg C/s or better.
Linear Dynamic range: must have greater than 107
Must be able to set data rate up to 500 Hz to accommodate peaks as narrow as 10 msec at half height
Must have maximum operating temperature of 450 °C
Must have electronic pneumatic control of make-up, H2 and air flows (with electronic ON/OFF). Air:
0 to 800mL/min,-H2 : 0 to 100 mL/min, -Makeup gas (N2 or He): 0 to 100 mL/min
Column adoptability: should be able to accommodate either capillary column or packed columns
TCD (Thermal conductivity detector)
• Minimum detectable level: 400 pg tridecane/mL with He carrier. (This value may be affected by
laboratory environment).
• Linear dynamic range: > 105 ± 5%
• Signal polarity can be run-programmed for components having higher thermal conductivity than the
carrier gas.
• Maximum temperature: 400 °C
• Standard EPC for 2 gases (He, H2, or N2 matched to carrier gas type)
• Make-up gas: 0 to 12 mL/min
• Reference gas: 0 to 100 mL/min
Electron Capture Detector-ECD (Optional)
Minimum detectable level:< 5.5 fg/mL lindane
Must have maximum operating temperature of 400 °C
Must have Standard EPC makeup gas types: argon/5% methane or nitrogen; 0 to 150 mL/min
Must have Linear dynamic range: > 5 × 104 with lindane
Must be equipped with hidden anode and high velocity flows to Minimizes contamination and
optimizes sensitivity
Data Handling Software :
- The chromatography software should be of latest of its version and be able to collect the data from
two
detectors simultaneously.
- The software should facilitate easy method building, data integration and custom report generation.
- The GC data system must have an integrated retention time-locking module for analyzing target
compounds in complex matrices. The software module must provide the creation of custom compound
databases for quick identification of analytes
- The software should facilitate manual as well as auto integration of the data.
- The software should have all the features required for audit trail under GLP/GMP with a password
locking facility.
- The software should have a real time display of the chromatogram and the process sample details.
- Software should be capable of data acquisition and processing and automatic integration.
- Report generation and interpretation should be automatic.
Computer and printer (Optional):
- The personal computer with latest processor/configuration with LCD monitor and Laser jet. Printer
should be supplied along with the instrument.
- The latest software which is compatible with the chromatography software should be supplied. A
Original windows latest software which is compatible with the chromatography software be supplied
with the system.
- The PC should be connected to the GC with an SIM to be able to communicate with the system
for its operation as well as process the date.
Gas cylinders
- Gas cylinders Nitrogen 2 Nos ultrapure grade IOLAR
- Above all cylinders Duly filled with gases
- Along with double stage gas regulators made of brass and filtration panel.
Other conditions:

The specifications are only a guide line and the supplier is at liberty to quote the better options
also, but the Instrument model should have been brought in to the market recently with a
proven record whose working demonstration can be arranged within the town in a short notice.

The manufacturer/supplier preferably provides support with required spares and services for a
minimum period of ten years of the model of the instrument quoted. All the required
accessories should be supplied along with the instruments for its optimum performance.

The manufacturer/supplier should arrange the training program in India for at least two faculty
or research scholars in operation of the instrument, its simple maintenance as well as
thoroughness in application of software either at JNTU, Pulivendula.

Supplier should supply with minimum spares and consumables that are required for working
and installation of the system.

Minimum 4 glass 20micro lit. Syringes for manual injections should be supplied along with the
system.
Important Note: The Instrument supplier must be either the original manufacturer or their
authorized distributor/dealer and an authorization letter to that effect must be enclosed along with
the quotation in case of latter.
ABSTRACT SCHEDULE –E.13
DEPARTMENT OF PHYSICS
Schedule
No
E-13.a
E-13.b
E-13.c
E-13.d
E-13.e
E-13.f
E-13 g
E-13 h
E-13 i
E-13.j
E-13.k
E-13.l
Name of the Item
Ball Mill
Furnace
Hydraulic Pellet Press
Spin-coating Unit
Vacuum Coating Unit
LCR meter
Electrometer
Ferroelectric loop tracer
Oven
Magnetic Stirrer
Electronic Weighing Machine
Mortar-pestle
Following gives detailed specifications
Quantity
01
01
01
01
01
01
01
01
01
02
01
01
Estimated
Amount
500000=00
700000=00
300000=00
100000=00
500000=00
500000=00
800000=00
500000=00
100000=00
10000=00
50000=00
10000=00
EMD
Amount
10000=00
14000=00
6000=00
2000=00
10000=00
10000=00
16000=00
10000=00
2000=00
200=00
1000=00
200=00
SCHEDULE –E.13
DEPARTMENT OF PHYSICS
E-13.a: Item
:
Ball Mill
Specifications of Ball Mill
S.No. Item
Specifications
1
Feed material
soft, hard, brittle, fibrous - dry or wet
2
3
4
Size reduction principle
Material feed size
Final fineness
impact, friction
< 10 mm
< 1 µm, for colloidal grinding < 0.1 µm
5
Batch size / feed quantity
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21.
No. of grinding stations
Speed ratio
Sun wheel speed
Effective sun wheel diameter
Type of grinding jars
Material of grinding tools
Grinding jar size
Grinding Balls of Zirconium
Setting of grinding time
Interval operation
Interval time
Pause time
Storable SOPs
Measurement of input energy
possible
Interface
Any related accessory
Max. 1 x 220 ml, max. 2 x 20 ml with stacked grinding
jars
1
1 : -2
100 - 650 min-1
141 mm
safety closure device for wet grinding
zirconium oxide
50 ml
10mm dia 12no’s;3mm 400pcs.
digital, 00:00:01 to 99:59:59
yes, with direction reversal
00:00:01 to 99:59:59
00:00:01 to 99:59:59
10
yes
21
Price
22
23
Installation
Commissioning
Demonstration
24
Operating Manuals
25
warranty
RS 232 / RS 485
The supplier should quote any related accessories (as
applicable)
Inclusive of all taxes and should include transportation and
fitting charges at customer site.
At customer site
and The supplier should make necessary commissioning of the
equipment with satisfactory experimental demo at customer
site
Must supply operating manuals in the form of hard copy and
soft copy (as applicable)
Must supply warranty of the equipment (as applicable)
E-13. b: Item
:
Furnace
Specifications of Furnace
S.No. Item
Specifications
1.
Type of Furnace
Muffle Furnace
2.
Maximum Temperature
1500°C
5
6
7
Max Continuous Temperature
Heating Elements
Insulation
8
9
10
11
12
13
14
15
16
1450°C
Silicon carbide elements
Low thermal mass ceramic fibre insulation and silicon
carbide elements, which radiate heat directly on to the work
piece, provide rapid heating and cooling. A robust silicon
carbide hearth tile is fitted as standard.
Steelwork
Outer case manufactured from zinc coated steel sheet
finished with a tough yet attractive epoxy paint. Double skin
construction allows natural air convection to maintain a cool
outer case.
Eurotherm
Temperature
3216P1
Control
advanced set point programming temperature controller with eight segmentpairs, each a ramp and a dwell. Scrolling text provides
additional information of current status to the user.
Temperature Sensors
Type '20/40'
Temperature Alarm
Should be available
Power Control
Via current limiting phase angle fire thyristor
Power Supply
220-240v single phase
Energy Rating
12 KW
Location of Controls
Within the furnace frame below the door.
Overall Ext. Dims
870mm High x 715mm Wide x 860mm Deep.
17
18.
19.
Weight
Heat up time
Gas inlet
17.
Any related accessory
18
Price
19
20
Installation
Commissioning
Demonstration
21
Operating Manuals
22
warranty
129Kg
50 minutes to 1400°C.
A 6mm hose connection on the outside of the furnace, piped
to a ceramic tube which leads gas (inert gas) into the
chamber.
The supplier should quote any related accessories (as
applicable)
Inclusive of all taxes and should include transportation and
fitting charges at customer site.
At customer site
and The supplier should make necessary commissioning of the
equipment with satisfactory experimental demo at customer
site
Must supply operating manuals in the form of hard copy and
soft copy (as applicable)
Must supply warranty of the equipment (as applicable)
E-13.c: Item
:
Hydraulic Pellet Press
Specifications of Hydraulic Pellet Press
S.No. Item
Specifications
1
Max. pressure
2
3
4
7
8
9.
Pressure force
Dies
Utility
pressing tools
Arrangement
Any related accessories
25t, hydraulic press with manual operation
1 - 25 t (10 - 250 kN)
ø 32 / ø 40 mm
To make high quality, stable pellets for characterization.
Available pressing tools (as applicable)
Compact bench top unit with Easy and safe operation
The supplier should quote any related accessories (as
applicable)
10.
Price
Inclusive of all taxes and should include transportation and
fitting charges at customer site.
11.
Installation
At customer site
12.
Commissioning
and The supplier should make necessary commissioning of the
Demonstration
equipment with satisfactory experimental demo at customer
site
13.
Operating Manuals
Must supply operating manuals in the form of hard copy and
soft copy (as applicable)
14.
warranty
Must supply warranty of the equipment (as applicable)
E-13.d: Item
:
Spin-coating Unit
Specifications of Spin-coating Unit
S.No. Name of the Unit
Item
Specifications
1.
Spin Coater
Precision controlling
micro controller
Speed range
100 RPM to 10000 RPM.
Speed accuracy
<±1% error across the full range.
Acceleration
2000 RPM/sec. (max.).
spinning control
Two stage
Mode selection switch
Single stage / Double stage
Real time display of RPM &
LED display
timing status
Current operation status
Status Panel
indication
Keypad and dial-knob
Input and control option.
Integrated vacuum release
on / off indication
switch on keypad
Calibration option
variable substrates
Spill drainage
Should be provided
Working chamber.
Teflon coated 8" diameter
substrate holder size
½”,1”,11/2”,2”,3” &4”
Integrated power on / off
Should be available
switch with indicator
Instrument dimension
15"(W), 10"(L) & 11"(H).
Power
230 / 220V AC
Wattage
150W
Power
220-240V/50,60Hz
2.
Oil Free
Vacuum Pump
Max. power
190
consumption(W)
Max. current (A)
1.0
Max. vacuum
730mmHg=97.33kPa=30Torr
Max. flow rate
33 I/min
Horse Power
1/4HP
3.
4.
5.
Manual Dispenser
Micro Syringe
Inert gas purging
port
Any related
accessories
Price
Pole
Net wet
Gross weight
Port thread
Noise Level
capacity
4P
7.6kg
8.6kg
5/16"
52dB
250 µl
Gas
Nitrogen
The supplier should quote any related accessories (as applicable)
Inclusive of all taxes and should include transportation and fitting
charges at customer site.
Installation
At customer site
7.
Commissioning and The supplier should make necessary commissioning of the
8.
Demonstration
equipment with satisfactory experimental demo at customer site
Operating Manuals
Must supply operating manuals in the form of hard copy and soft
9.
copy (as applicable)
warranty
Must supply warranty of the equipment (as applicable)
10
E-13.e: Item
:
Vacuum Coating Unit
Specifications of Vacuum Coating Unit
S.No. Item
Specifications
6.
1
2
HIGH VACUUM CHAMBER High Vacuum Chamber: cylindrical metal bell jar made of
FOR COATING
non-magnetic stainless steel SS-304
Dimensions: diameter 300mm x 400mm height.
Facility: With water cooling and view port window and Lgasket
Base plate: number of ports having 1” dia, for taking
various vacuum feed through for operation of different
gadgets.
CHAMBER ACCESSORIES
1. L.T. POWER SUPPLY
Thermal evaporation: 2 LT power supply transformers
(200Amps 10 Volts)
Two pairs of LT evaporation electrical feed should be
provided.
2. ION BOMBARDMENT
Discharge cleaning system:
super pure aluminum
electrode bar (3.5KV,50ma)
3. GAS INLET SYSTEM
4. VACUUM PUMPING
SYSTEM:
Gas inlet system:Needle Valve to inert gases.
a. ROTARY MECHANICAL PUMP:
Direct Drive Rotary mechanical
pump (250) LPM
b. DIFFUSION PUMP:
Oil diffusion pump: pumping speed
of 350 L/sec for high vacuum
operation.
c. HIGH VACUUM VALVE:
High vacuum valve: 4 ½”.
Quarter swing butterfly valve: 4”.
d. COLLAR: 4” collar
e. MOUNTING: The mounting frame
made out of M.S material. The frame
is powdered coated for dust-free
operation. Anti vibration mounts for
3.
PLUMBING LINES
4.
5.
6.
7.
POWER SUPPLY
WATER
Digital Thickness Monitor unit
SUBSTRATE HEATER
8.
9.
10.
11.
12.
13.
rotary vacuum pump should be
provided for the reducing the
vibrations.
f. VACUUM MEASURING GAUGES:
Stabilized Digital pirani gauge with
two pirani gauge heads must be
provided to independently monitor the
roughing and backing pressure.
The pirani gauge must measure vacuum
level from 0.999 to 0.001m.bar.
Stabilized Digital Penning gauge with
one gauge head should be provided to
monitor high vacuum, from 9.9 x 10-3
to 1 x 10-6 m.bar 10-6m.bar.
Plumbing lines: SS304 material of 1” NB with 02 Nos of
Butterfly valves for both backing and roughing operation.
220VAC, 50Hz, Single Phase, 15 Amps.
4-5 lit/min, 20-25 deg.C 24 PSI
Should be provided
Substrate heater: 450 degree.
The temperature measurement and control: Digital
Controller with K Type Thermocouple with SSR Power
Controller for feeding smooth power to the heater.
Glass & Wafer
Should be provided
Should be provided
Should be provided
Should be provided
Should be provided
Substrates
Rotation
Rotary and diffusion pumps oils
Vacuum grease
Diffusion pump heater
Evaporation sources of
Molybdenum boats &
Tungsten helical coils.
14.
Some
small
quantity
of Should be provided
evaporation grade Aluminium
15.
L N2 cylinder (25L) 50K
Should be provided
16.
Any related accessories
The supplier should quote any related accessories (as
applicable)
17.
Price
Inclusive of all taxes and should include transportation and
fitting charges at customer site.
18.
Installation
At customer site
19.
Commissioning
and The supplier should make necessary commissioning of the
Demonstration
equipment with satisfactory experimental demo at
customer site
20.
Operating Manuals
Must supply operating manuals in the form of hard copy
and soft copy (as applicable)
21.
warranty
Must supply warranty of the equipment (as applicable)
E-13. f: Item
:
LCR meter
Specifications of LCR meter
S.No. Item
Specifications
1
Measurement parameters
2
Measurement ranges |Z|, R, X
3
θ
|Z|, |Y|, θ, Rp, Rs (ESR), G, X, B,
Cp, Cs, Lp, Ls, D (tan δ), Q
10.00 mΩ to 200.00 MΩ (100 mΩ, 1 Ω, 10 Ω, 100 Ω, 1 kΩ,
10 kΩ, 100 kΩ, 1 MΩ, 10 MΩ, 100 MΩ)
-180.00° to +180.00°
4
C
0.3200 pF to 370.00 mF
5
6
7
8
9
10
L
D
Q
|Y|, G, B
Basic accuracy
Measurement frequency
11
Measurement signal levels
12
13
14
Output impedance
Display screen
Measurement time (typical
values for displaying |Z|)
Settings in memory
Comparator functions
16.000 nH to 750.00 kH
0.00001 to 9.99999
0.01 to 999.99
5.0000 nS to 99.999 S
Z : ± 0.08% rdg. θ : ± 0.05˚
42 Hz to 5 MHz (Up to 1 kHz (0.1 Hz steps); 1 kHz to 10
kHz (1 Hz); 10 kHz to 100 kHz (10 Hz); 100 kHz to 1 MHz
(100 Hz); 1MHz to 5 MHz (1 kHz)
10 mV to 5 V rms / 10μA to 100 mA rms
Voltage and constant voltage: 10 mV to 5 V rms (DC to 1
MHz) 50 mV to 1 V rms (1 MHz to 5 MHz) Maximum
short-circuit current 100 mA rms 1 mV steps
Constant current: 10 μA to 100 mA rms (DC to 1 MHz) 50
μA to 20 mA rms (1 MHz to 5 MHz) Maximum voltage 5 V
rms 10 μA rms steps
50 Ω
LCD with backlight / 99999 (full 5 digits)
FAST : 5 ms, NORMAL : 21 ms,
SLOW 1 / 2 : 72 ms / 140 ms
Maximum 30 sets
HI/IN/LO settings for two measurement parameters;
percentage, Δ%, or
absolute value settings
15
16
17
18
19
20
21
100, 120, 220 or 240 V(±10%) AC (selectable), 50/60 Hz
50 VA approx.
13.86”W × 4.88”H × 12.72”D
As applicable
(2 m/78.74”)
22
Power source
Maximum rated power
Dimensions
9518-01 GP-IB INTERFACE
9151-02
GP-IB
CONNECTION CABLE
FOUR-TERMINAL PROBE
23
24
DC BIAS VOLTAGE UNIT
Any related accessories
25
Price
26
Installation
As applicable
The supplier should quote any related accessories (as
applicable)
Inclusive of all taxes and should include transportation and
fitting charges at customer site.
At customer site
27
Commissioning
Demonstration
28
Operating Manuals
29
30
warranty
Any related accessories
E-13. g : Item
Specifications of Electrometer
S.No. Item
DC to 100 kHz
and The supplier should make necessary commissioning of the
equipment with satisfactory experimental demo at customer
site
Must supply operating manuals in the form of hard copy and
soft copy (as applicable)
Must supply warranty of the equipment (as applicable)
The supplier should quote any related accessories (as
applicable)
:
Electrometer
Specifications
1.
Electrometer
Measurement range:
Volts: 200mV to 200 V
Amp: 2 nA to 2 A
Ohms: 2 K Ω to 2 T Ω
Channels: independent, separately programmable 5 1/2-digit
measurement channels
Dual Channel: Dual channels allow measurements at each
node of a device Channel A and optional Channel B have
independent analog signal grounds and independent function
and range programming

Data Storage: up to 50 readings
Auto/Manual, Up, down
Zero check/Zero correction
Resolution:51/2 digits
Interfaceability: 6193 interface option
Filter
Display: Numeric, 0.56” LED digits
Input current: <0.4 PA
Power: 210-250V (50Hz)
Dimensions:17”x5”x16’ (WxHxD)
Weight: 9.8 kg.
2.
Any related accessories
The supplier should quote any related accessories (as
applicable)
3.
Price
Inclusive of all taxes and should include transportation and
fitting charges at customer site.
4.
Installation
At customer site
5.
Commissioning
and The supplier should make necessary commissioning of the
Demonstration
equipment with satisfactory experimental demo at customer
site
6.
Operating Manuals
Must supply operating manuals in the form of hard copy and
soft copy (as applicable)
7.
warranty
Must supply warranty of the equipment (as applicable)
E-13.h : Item
:
Ferroelectric loop tracer
Specifications of Ferroelectric loop tracer
S.No. Item
Specifications
1
Voltage Range
Number of ADC Bits
Minimum Charge Resolution
The Multi Ferroic Test System should allow below 10V is
capable of executing a single pass hysteresis loop in 100us
with no interlacing of the data acquisition. Using its 40MKz
clock, the Multi Ferroic will interface multiple loops to
generate an effective capture rate of 10MHz for a total loop
period of 10us. The 100V Multi Ferroic system will execute
up to the 20us limit. Also Able to execute Hysteresis,
Remanent hysteresis, small signal CV, IV, fatigue, imprint,
retention, and piezoelectric displacement from one hardware
configuration.
±100V (no external amp), ±10KV (with external amp)
16
1mC (w/HVI: 100 mC)
Maximum Charge Resolution
1mC (w/HVI: 100 mC)
Multi Ferroic Test System
2.
3.
4.
5.
Maximum Area Resolution
Hysteresis Frequency range
Minimum Pulse Width
Delay between Pulses
Minimum Leakage Current
Signal Cap Freq.
Output Rise Time Control
Input Capacitance
connecting cables
High Voltage Interface
Maximum Voltage Rating
> 100cm2
0.05 Hz 100 KHz
< 1 μs
< 50ks; Internal Clock: 25ns
< 2pA
1Hz (minimum), 1MHz (maximum)
105 scaling
< 100fF
Should be provided
High Speed Protection Current
Rating
High Speed Protection Trigger
Voltage
Low Speed Protection Delay
Time
Insulation Rating
connecting cables
High Voltage Power Amplifier
Output Voltage Range
Output Current Range
Input Voltage Range
DC Voltage gain
DC Voltage gain accuracy
Offset Voltage
Output Noise
Slew Rate
Settling time to 1%
Temperature Drift
Time Drift
voltage monitor of DC
accuracy
output noise
connecting cables
High Voltage Test Fixture
10 Amps
Maximum temperature
Maximum voltage
600°C
10KV
10KV (AC); Power: 220V AC, 50 Hz
2.1V
17ms
> 40KV DC
Should be provided
0 to ±10 KV DC
0 to ±2 mA DC
0 to ±10 V DC
1000V/V (noninverting)
better than 0.1%
< ±1V
< 50mV rms
> 30V/Î
Less than 700 Î
< 180 ppm/0C
< 50 ppm/hr
better than 0.1%
< 5mV rms
Should be provided
high temperature and high Should be provided
voltage cables
Displacement Sensor
Output Signal
0-10 Vdc
Drift
< 1% of full scale
Vibration Measurement 0-10Vdc
Output Signal:
Accuracy
within 1 % for peak to peak reading of full scale
Interface
RS 232
Displacement data accuracy
< 1% for signals from dc to 100 Hz
Vibration data accuracy
1% for peak-to-peak displacement of full scale
Display meter
Graphic LCD with 100 Hz response.
Supply
220V AC, 50 Hz
software for displacement and Should be provided
strain measurements
6.
With Photonic probe of maximum measurement range of 4 X 10-4 Inch, Sensing frequency of
100 kHz and Accuracy of ± 1% of full scale. With Probe Positioning fixture Capable of
positioning the Photonic probe over the sample to be measured and consisting of magnetic
base, mounting clamp and micrometer.
7.
.High Voltage Displacement
Text fixture
Maximum Voltage
10 KV
Maximum Temperature
200oC
stable
platform
for Should be provided
displacement measurements
8.
Any related accessories
The supplier should quote any related accessories (as
applicable)
9.
Price
Inclusive of all taxes and should include transportation and
fitting charges at customer site.
10.
Installation
At customer site
11.
Commissioning
and The supplier should make necessary commissioning of the
Demonstration
equipment with satisfactory experimental demo at customer
site
12.
Operating Manuals
Must supply operating manuals in the form of hard copy and
soft copy (as applicable)
13
warranty
Must supply warranty of the equipment (as applicable)
E-13.i: Item
:
Oven
Specifications of Oven
S.No. Item
Specifications
1
Inside Body
Stainless Steel ( SS 304 )
2
3
4
Out Side Body
No. of Selves
Body Structure
MS Powder coated with stove enamel paint.
2 Adjustable Perforated Selves.
Double Walled structure filled with glass wool insulation
5
6
7
No. of Heaters
Heater’s Quality
Air Circulation
8
9
10
11
12
13
14
15
16
Ventilation
Temp. Control
Temp. Display
Range of Temp
Accuracy
Least Count
Power
Inner Chamber Sizes
Any related accessories
17
Price
2 x 1000 Watts
High Quality Chrome Heater insulated with ceramic beads
By Air Circulating Fan to ensure even temperature
distribution.
Ventilation port with adjustable Opening.
By Digital Temperature indicator and Controller
Digital Temp. display
Ambient to 2500C (0 – 6000C)
0.1 0C
1 0C
220 Volt AC 50 Hz. Single Phase
24” x 24” x 24”
The supplier should quote any related accessories (as
applicable)
Inclusive of all taxes and should include transportation and
fitting charges at customer site.
18
19
Installation
Commissioning
Demonstration
At customer site
and The supplier should make necessary commissioning of the
equipment with satisfactory experimental demo at customer
site
20
Operating Manuals
Must supply operating manuals in the form of hard copy and
soft copy (as applicable)
21
warranty
Must supply warranty of the equipment (as applicable)
E-13.j: Item
:
Magnetic Stirrer
Specifications of Magnetic Stirrer
S.No. Item
Specifications
1
Magnetic Stirrer with Hot
Plate and Digital Speed
Indicator
Top housing: Stainless steel
Speed regulator: Variable with low and
high seed toggle switch
Other fitted items: Energy regulator and
Heating controller.
No. of stirring paddle: One.
Operating Voltage: 230V AC mains.
2
3.
Capacity
Any related accessories
4.
Price
5.
Installation
5 Litre
The supplier should quote any related accessories (as
applicable)
Inclusive of all taxes and should include transportation and
fitting charges at customer site.
At customer site
6.
Commissioning
and Demonstration
1.
Electronic weighing machine
The supplier should make necessary commissioning of the
equipment with satisfactory experimental demo at customer
site
7.
Operating Manuals
Must supply operating manuals in the form of hard copy and
soft copy (as applicable)
8.
warranty
Must supply warranty of the equipment (as applicable)
E-13. k: Item
:
Electronic Weighing Machine
Specifications of Electronic Weighing Machine
S.No. Item
Specifications
Capacity: 220gms
Readability: 0.0001gm (0.1mg)
Repeatability: 0.0001 gm
Non Linearity:±0.0003gm
2.
Any related accessories
3.
Price
4.
5.
Installation
Commissioning
Demonstration
Pan size: 80 mm diameter
Calibration: External
Housing Dimensions: 200 x 290 x 314 mm (WDH)
Weighing Units: mg, g, ct, oz, dwt, mom, GN
Power: 230 Volts AC, DC9V
Weight: approx. 3 kg
The supplier should quote any related accessories (as
applicable)
Inclusive of all taxes and should include transportation and
fitting charges at customer site.
At customer site
and The supplier should make necessary commissioning of the
equipment with satisfactory experimental demo at customer
6.
Operating Manuals
7.
warranty
E-13. l: Item
:
Specifications of Mortar-pestle
S.No. Item
1
site
Must supply operating manuals in the form of hard copy and
soft copy (as applicable)
Must supply warranty of the equipment (as applicable)
Mortar-pestle
Specifications
Mortar & Pestle
Quality: Original Natural Agate
2
3
Price
4.
warranty
Inside diameter approx: 5” I.D.
Inclusive of all taxes and should include transportation to
customer site.
Must supply warranty of the equipment (as applicable)
ABSTRACT OF SCHEDULE –E.14
DEPARTMENT OF MATHEMATICS
COMPUTATIONAL FLUID DYNAMICS LAB
Schedule
Quantity Estimated
Name of the Item
No
Amount
COMPUTATIONAL FLUID DYNAMICS LAB
E.14
E. 14.a
Mat Lab Software
10 users 400000=00
E. 14.b
Mathematica Software
10 users 400000=00
Following gives detailed specifications
EMD
Amount
8000=00
8000=00
SCHEDULE –E-14
DEPARTMENT OF MATHEMATICS
COMPUTATIONAL FLUID DYNAMICS LAB
E. 14.a
Item
:
Mat Lab Software
MAT-LAB With latest Version:
1.
2.
3.
4.
5.
6.
7.
6.
Quantity
10 users
10 users
10 users
10 users
10 users
10 users
10 users
10 users
10 users
MATLAB (Latest Version with following Toolboxes)
SIMULINK
Neural Network Toolbox
Fuzzy Logic Toolbox
Image Processing Tool Box
Bio Informatics
Optimization Tool Box
Genetic algorithms
Curve Fitting, Partial Differential Equations and all
7. Mathematical Tool Boxes
10 users
8 Statistical Tool Box, Mapping Tool Box
Note : 1.The Price quoted should include transportation and installation charges.
Item
:
Mathematic Software
Mathematic With latest Version:
E. 14.b
1. Mathematic (Latest Version with required Toolboxes)
2. All Mathematical related Tool Boxes
Quantity
10 users
10 Users
Note : 1.The Price quoted should include transportation and installation charges.
ABSTRACT SCHEDULE –S.1
Computers (Desk Top Computer Systems)
Schedule
No
S.1
Name of the Item
Computers (Desk Top Computer Systems)
Following gives detailed specifications
Quantity
176
Estimated
Amount
6170000=00
EMD
Amount
123400=00
SCHEDULE –S.1
Computers (Desk Top Computer Systems):
Specifications
S.No. Item
1.
Make and Model
2.
Processor
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
Chipset
Memory
Memory Expandability
Hard Disk Drive
Optical Drive
Network Interface
Graphics
I/O Ports
Expansion Slots
Monitor
Keyboard
Mouse
Warranty
Delivery
Price
18.
Operating Systems
Desktop Computer Systems
Specifications
Should be specified by the Vendor
Intel® Core i5 2.8GHz or Higher with FSB 1000 MHz or
Higher
Intel Chipset
4 GB DDR3 SDRAM
At least Upto 8 GB
500 GB SATA Hard Drive at 7200 rpm or better
DVD Writer with Dual layer write capability
10/100/1000 Mbps
Integrated Intel® Graphics Accelerator
Minimum of 6 USB Ports, Atleast 2 at front side
3 PCI Slots
18.5” Color TFT LCD Monitor
Standard Key Board
Optical Mouse
3 Years Comprehensive On Site Warranty
At the Customers site
Inclusive of all taxes and should include transportation and
installation charges at customer site
Should support for Microsoft and UNIX related Operating
Systems
ABSTRACT SCHEDULE –S.2
Net working
Schedule
Name of the Item
No
S.2
Networking
S.2.a
S.2.b
S.2.c
S.2.d
Net working (LAN)
Net working
Networking Internet connection
Networking Internet connectivity
Following gives detailed specifications
Quantity
40 systems
65 systems
30 systems
10 systems
Estimated
Amount
100000=00
120000=00
60000=00
30000=00
EMD
Amount
2000=00
2400=00
1200=00
600=00
SCHEDULE –S.2
Networking
S.2.a. Networking (LAN) Specification:
Task
: Networking of Simulation lab, computers Each of capacity 40 computers/
Peripherals
Connectivity
: Wired
No. of I/O boxes of standard make
: 40
No. of patch cards of standard make
: 40
No. of RJ45 connectors of standard make: 40 X 2 = 80
Approximate Length of the wire required: 1000 mts
Type of Cable
: CAT 6
No. of Switches (24 ports) of standard make: 3
No. of racks: 1 - capable of holding three switches
Ducts : Yes, of good quality for running the cable.
Warranty
: 1 year Warranty on parts
Note:
1.
You are requested to visit the computer labs to know the actual dimensions of the room
and physical alignment of systems before giving your quotations.
2.
The price quoted should include transportation, installation and labour charges for
fixing the ducts etc.
3.
Make of switches, I/O boxes etc has to be specified by the vendor
4.
The task of networking a computer lab shall be evaluated as a Unit for evaluation
S.2.b. Specifications
Networking of Labs Specifications
S.No.
Item
Specifications
1.
Connectivity
Wired
2.
No. of I/O boxes of standard make
65
3.
No. of patch cards of standard make
65
4.
No. of RJ45 connectors of standard
65 X 2 = 130
make
5.
Approximate Length of the wire
1200 mts
required
6.
Type of Cable of standard make
CAT 6
7.
No. of Switches (24 ports) of standard 3
make
8.
No. of racks
1 - capable of holding three switches
9.
Ducts
Yes, of good quality for running the
cable
10.
Warranty
1 year Warranty on parts
Note: 1. You are requested to visit the computer lab to know the actual dimensions of the
room and physical alignment of systems before giving your quotations
2. The price quoted should include transportation, installation and labour charges
for fixing the ducts etc.
3. Make of switches, I/O boxes etc has to be specified by the vendor.
4. The task of networking a computer lab shall be evaluated as a Unit.
S.2.c Specifications:
 BSNL Broad band connections
Networking of Labs Specifications
S.No.
Item
Specifications
1.
Connectivity
Wired
2.
No. of I/O boxes of standard make
30
3.
No. of patch cards of standard make
30
4.
No. of RJ45 connectors of standard
30 X 2 = 60
make
5.
Approximate Length of the wire
1200 mts
required
6.
Type of Cable of standard make
CAT 6
7.
No. of Switches (24 ports) of standard 3
make
8.
No. of racks
1 - capable of holding three switches
9.
Ducts
Yes, of good quality for running the
cable
10.
Warranty
1 year Warranty on parts
Note: 1. You are requested to visit the computer lab to know the actual dimensions of the
room and physical alignment of systems before giving your quotations
2. The price quoted should include transportation, installation and labour charges
for fixing the ducts etc.
3. Make of switches, I/O boxes etc has to be specified by the vendor.
4. The task of networking a computer lab shall be evaluated as a Unit.
S.2.d. Specificatons:
Networking of Labs Specifications
S.No.
Item
Specifications
1.
Connectivity
Wired
2.
No. of I/O boxes of standard make
65
3.
No. of patch cards of standard make
65
4.
No. of RJ45 connectors of standard
65 X 2 = 130
make
5.
Approximate Length of the wire
1200 mts
required
6.
Type of Cable of standard make
CAT 6
7.
No. of Switches (24 ports) of standard 3
make
8.
No. of racks
1 - capable of holding three switches
9.
Ducts
Yes, of good quality for running the
cable
10.
Warranty
1 year Warranty on parts
Note: 1. You are requested to visit the computer lab to know the actual dimensions of the
room and physical alignment of systems before giving your quotations
2. The price quoted should include transportation, installation and labour charges
for fixing the ducts etc.
3. Make of switches, I/O boxes etc has to be specified by the vendor.
4. The task of networking a computer lab shall be evaluated as a Unit.
ABSTRACT SCHEDULE –S.3
10 KVA Online UPS
Schedule
No
S.3
Name of the Equipment
10 KVA Online UPS
Following page gives detailed specifications
Quantity
Estimated
Amount
04
1000000=00
EMD
Amount
20000=00
SCHEDULE –S.3
S.3.a. Item: 10 KVA Online UPS
Specifications:
Input: 320V AC to 480V AC, 50Hz, Three phase, Four wire, Frequency: 50± 3 Hz
Output: Voltage: 230V AC/240V AC (Any One Voltage) Single Phase, Sine Wave
Frequency: 50Hz ±0.5Hz Free Running, optional ±0.05% & 50Hz ±3Hz Sync Mode
Regulation: ±1%
Inverter technology : PWM(On-Line Double Conversion with IGBT)
Crest Factor: 3:1
Distortion: ≤ 2%(Linear load)
Efficiency ; ≥ 85 % AC to AC (Linear Load)
Load power factor : 0.8 lag
Static Bypass /Batteries:
Maintenance-free SMF battery with suspended electrolyte: leak proof,
expected battery life 3-5 years, Recharge time of 6 hours,
Backup time of one hour at Full Load
Protections : Mains Over/Under Voltage, Phase Fail, DC Over/Under Voltage, Inverter
Over/Under Voltage, Inverter Overload, Overheat, Built-in Soft/Cold Start
and Snubber Circuits for Devices
LED Indicators: Mains ON, Inverter ON, Battery On Charge, Mains abnormal, Low
Battery Imminent, DC Over/Under Voltage, Inverter Over/Under
Voltage, Inverter Overload, Overheat,
Optional:Load On Inverter, Load On Aux. Supply, Manual Bypass On
Digital Metering: 16x2 LCD for I/P & O/P Volts, DC Volts, Frequency, Load & Battery
percentage (optional-I/P Volts)
Humidity: 95%, Temparature:0 to 450, Protection Class:IP21
Others:
Built in power buzzer Audible Alarm, Emergency Power Off, 10-50degree Celsius, 3 Years Onsite
Comprehensive Warranty
Back up time: 3Hrs on full load
ABSTRACT OF SCHEDULE –S.4
15 KVA Online UPS
Schedule
No
S.4
Name of the Equipment
15 KVA Online UPS
Following page gives detailed specifications
Quantity
Estimated
Amount
01
450000=00
EMD
Amount
9000=00
SCHEDULE –S.4
S.4. Item: 15 KVA Online UPS (Centralized Computer Centre)
Specifications
15 KVA Online UPS
Specifications
S.
No.
1.
2.
3.
4.
5.
Item
6.
7.
8.
9.
10.
11.
12.
13.
14.
Backup Time
Recharge Time
Transfer Time
Rack for Batteries
Transportation and Installation
Indicators
Lightening and Surge Protection
Protection
Electric Wire
15.
16.
Efficiency at full load
Warranty
17.
Price
18.
Protection
Make and Model
Capacity
Input Voltage
Output voltage
Batteries
To be specified by the vendor
15 KVA, 3 phase input, single phase output
360-450VAC, frequency 45-55Hz
230V +/- 2%, Pure Sine Wave
12V 100AH Sealed Lead Acid SMF Batteries
40 in number.
3 Hrs on Full Load
10 Hrs
0
Yes
Free of cost at customer site
Mains ON, Invertors ON, Charger ON
Yes
Input and Output – MCB
Wire Connecting UPS to Main Supply –
Should be provided by the vendor
92% or Better
3 Years Comprehensive On-site warranty for
UPS, 2 Years Comprehensive On-site
warranty for Batteries
Inclusive of all taxes and should include
transportation and installation charges at
customer site
At the point of inter-connections of the
batteries rubber covering should be provided
to prevent electrical shock
ABSTRACT OF SCHEDULE –S.5
Air conditioners
Schedule
No
S.5
Name of the Equipment
Air Conditioners
Following page gives detailed specifications
Quantity
Estimated
Amount
93
3436000=00
EMD
Amount
68720=00
SCHEDULE –S.5
Item: Air Conditioners
2.0 Ton Air Conditioner along with the following accessories
a) Stabilizer
b) Remote control
c) AC –box with 3 top pin, with MCB (6x4) and permanent type 3 pin socket.
Specifications
Make and model
: To be specified by the Vendor
Warranty
: One year comprehensive on-site warranty
Star Rating
: 5 star
Rated Cooling Capacity: 6700 (W)
Rated Power input
: 2400 (W)
Running Current
: 11.56 Amps
Air Flow volume
: 1000
Refrigerate
: R22
Compressor
: Rotary
Note:
1. The length of the card connecting AC’s to power point should be at least 4.0 mts.
(in case length of the wire required is more than 2m, it should be provided by the
vendor only)
2. The price quoted should include transportation and installation charges at JNTUA
College of Engineering, Pulivendula.
ABSTRACT OF SCHEDULE –S.6
Printers
Schedule
No
S.6
S.6.a
S.6.b
S.6.c
S.6.d
Name of the Equipment
Printers
1. Laser jet printer with 12A cartridge
2. Desk jet printer
3. Dot Matrix Printer
1. Laser Jet Color Printer
2. Laser Jet Black and White
Printer
Printer cum scanner
Following page gives detailed specifications.
Quantity
04
02
01
01
01
01
02
Estimated
Amount
EMD
Amount
70000=00
1400=00
50000=00
1000=00
20000=00
16000=00
400=00
320=00
SCHEDULE –S.6
Printers
S.6.a. 1) Laser Jet - Specifications
Printer capacity and ratings
Print Speed
Media input tray capacity
Output bin capacity
Minimum paper size
Maximum paper size
Base memory
Print resolution
Port availability
USB
Warranty
 18 pages per minute(ppm) for A4-size
paper.
 First page out in less than 8.5 seconds
Up to 260 sheets.
Up to 100 sheets.
76 by 127 mm (3 by 5 inches).
216 by 356 mm (8.5 by 14 inches).
32 MB of RAM
Upto 1200 x 1200 dpi.
Compatible with USB 2.0 specification.
1 year comprehensive on-site Warranty
S.6.a. 2) Desk Jet printer: Specifications
Printer capacity and ratings
Print Speed Black –A4 draft
Print speed black (ISO, laser comparable)
Print speed color (ISO, laser comparable)
Print quality black (best)
Upto 16 pages per minute(ppm)
Up to 5.5 ppm.
Maximum paper size
Base memory
Up to 4. ppm
Upto 600 dpi
216 by 356 mm (8.5 by 14 inches).
Integrated
Number of print cartridges
2 [1 black, 1 Tri-color (cyan, magenta, yellow)]
Port availability
USB
Warranty
Compatible with USB 2.0 specification.
1 year comprehensive on-site Warranty
S.6.a. 3) Dot Matrix printer [80 columns]: Specifications
Printer capacity and ratings
Letter Quality
Print speed
75
Draft 10 cpi
Letter Quality (12 cpi) (cps)
Ribbon Cartridge (Type)
Ribbon Cartridge (Colours)
Width (mm)
Height (mm)
Depth (mm)
90
Fabric Ribbon Cartridge
Black
366
159
275
Maximum Line Spacing (Inches)
Original plus Carbon Copies
Built-In-Fonts (Scalable Font Sizes)
Port availability
USB
Warranty
1/360
1+3
8 - 32
Compatible with USB 2.0 specification.
1 year comprehensive on-site Warranty
Note: Vendor has to give compliance report of the product with the specifications given. The bid
without compliance report shall be rejected.
S.6.b.1.Item: Laser Jet Color Printer Specifications
Laser Jet Color Printer
Specifications
300 sheets
Ethernet support
Hi-speed USB 2.0
Automatic
128 MB
1 Year Comprehensive Onsite warranty
Upto 15 pages per minute
2
Inclusive of all taxes and should include
transportation and installation charges at
customer site
S.6.b.2: Item: Laser Jet Black and White Printer Specifications
Laser Jet Black and White Printer
S. No.
Item
Specifications
1.
Input Capacity
500 sheets
2.
Network Ready
Yes
3.
Connectivity standard
Hi-speed USB 2.0 and Giga bit Ethernet
4.
Payer Trays
Two
5.
Print Resolution
1200 x 1200 dpi
6.
Memory
128 MB
7.
Warranty
1 Year Comprehensive Onsite warranty
8.
Print Speed
Upto 30 pages per minute
9.
Duplex printing
Automatic Preferred but not mandatory
11.
Price
Inclusive of all taxes and should include transportation
and installation charges at customer site
S.6.c. Item : Printer Specifications
S.No. Item
Specifications
S. No.
1.
2.
3.
4.
5.
6.
7.
8.
11.
Item
Input Capacity
Networking
Connectivity standard
Duplex printing
Memory
Warranty
Print Speed
Paper Trays
Price
1
All in one
Print, Copy, Scan, Fax
2
3
4
Print/copy
machine
sheet ADF
up to 26 ppm
Flatbed
35-sheet ADF
5
6
7
8
11
Monthly duty cycle
monthly page volume
input tray
priority tray
Price
12.
13.
14.
Installation
Commissioning
Demonstration
Operating Manuals
15.
warranty
up to 8000 pages
500 to 2000
250-sheet
10-sheet
Inclusive of all taxes and should include transportation and
fitting charges at customer site.
At customer site
and The supplier should make necessary commissioning of the
printer with satisfactory experimental demo at customer site
Must supply operating manuals in the form of hard copy and
soft copy (as applicable)
Must supply warranty of the equipment (as applicable)
S.6.d. Printer cum Scanner Specifications:
Printer capacity and ratings
Print Speed
Media input tray capacity
Output bin capacity
Minimum paper size
Maximum paper size
Base memory
Print resolution
Scanner
Port availability
USB
Warranty
 18 pages per minute(ppm) for A4-size
Paper.
 First page out in less than 8.5 seconds
Up to 260 sheets.
Up to 100 sheets.
76 by 127 mm (3 by 5 inches).
216 by 356 mm (8.5 by 14 inches).
32 MB of RAM
Upto 1200 x 1200 dpi.
A4 compatibility
Compatible with USB 2.0 specification.
1 year comprehensive on-site Warranty
Note: Vendor has to give compliance report of the product with the specifications given. The bid
without compliance report shall be rejected.
ABSTRACT OF SCHEDULE –S.7
Server
Schedule
No
Name of the Equipment
Quantity
Estimated
Amount
01
02
01
300000=00
500000=00
200000=00
EMD
Amount
Server
S.7
a. Server System
b. Server System
c. Server System
Following page gives detailed specifications
6000=00
10000=00
4000=00
SCHEDULE –S.7
S.7.a. Server System Specifications:
S. No Item
Specification
1
Make
To be specified by the Vendor
2
Processor
At least two six core Intel Xeon Processors
3
Server mounting
Tower mount
4
Chip set
Intel chipset
5
Memory
16 GB ECC DDR3
6
Memory expandability
At least upto 64 GB
7
Hard disk
Four 500 GB SATA/SAS
8
Optical drive
DVD Writer
9
Network interface Card
Dual independent 10/100/1000 Mbps Ethernet Controller
10
11
Raid controllers
At least 1 serial and 6 USB 2.0 ports, at least two front
side
Yes
12
Floppy Drive
3.5” Floppy drive
13
Monitor
22’’ TFT LCD color monitor
14
Keyboard
Multimedia Keyboard
15
Mouse
Optical scroll mouse
16
Delivery
At the customer site
Inclusive all taxes and should include transportation and
installation charges at customer site
Should support for Microsoft and unix related operating
system
3 years on site comprehensive warranty
Should be supplied in the form of CD / DVD and
preferable made available in the equipment manufactures
web site
17
18
19
I/O Ports
Price
Operating systems
Warranty
20
Drivers
S.7.b. Server System Specifications
S.No.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Item
Make and Model
Processor
Chipset
Memory
Memory Expandability
Hard Disk Drive
Optical Drive
Bays
Network Interface
10.
11.
12.
Graphics
I/O Ports
RAID Controllers
Specifications
Should be specified by the Vender
Atleast Two 6 core Intel Xeon Processors
Intel Chipset
16 GB ECC DDR3
Atleast Upto 64 GB
Four 500 GB SATA/SAS
DVD Writer with Dual layer write capability
Minimum of 8 Bays
Two 10/100/1000 Mbps Wired LAN Cards, one Wireless LAN
Card with Antenna and Supporting standards IEEE 802.11 a/b/g
Integrated Intel® Graphics Accelerator
Minimum of 6 USB Ports, Atleast 2 at front side
YES
13.
14.
15.
16.
17.
18.
Floppy Drive
Monitor
Keyboard
Mouse
Operating Systems
Drivers
19.
20.
21.
Warranty
Delivery
Price
3.5” floppy Drive
22” Color TFT LCD Monitor
Standard Key Board
Optical Mouse
Should support Microsoft and UNIX related Operating Systems
Should be supplied in the form of CD/DVD and preferably made
available in the equipment manufactures web site
3 Years Comprehensive On Site Warranty
At the Customer’s site
Inclusive of all taxes and should include transportation and
installation charges at customer site
S.7.c. Server System Specifications
S.No Item
Specification
1
Make
To be specified by the Vendor
2
Processor
At least two six core Intel Xeon Processors
3
Server mounting
Tower mount
4
Chip set
Intel chipset
5
Memory
16 GB ECC DDR3
6
Memory expandability
At least upto 64 GB
7
Hard disk
Four 500 GB SATA/SAS
8
Optical drive
DVD Writer
9
Network interface Card
Dual independent 10/100/1000 Mbps Ethernet Controller
10
I/O Ports
At least 1 serial and 6 USB 2.0 ports, at least two front side
11
Raid controllers
Yes
12
Floppy Drive
3.5” Floppy drive
13
Monitor
22’’ TFT LCD color monitor
14
Keyboard
Multimedia Keyboard with USB
15
Mouse
Optical scroll mouse
16
Delivery
At the customer site
Inclusive all taxes and should include transportation and
installation charges at customer site
Should support for Microsoft and unix related operating system
17
Price
18
Operating systems
19
Warranty
20
Drivers
3 years on site comprehensive warranty
Should be supplied in the form of CD / DVD and preferable
made available in the equipment manufactures web site
ABSTRACT OF SCHEDULE –S.8
LCD Projector
Schedule
No
S.8
Name of the Equipment
LCD Projector
a. LCD Projector
b. LCD Projector
c. LCD Projector
Following page gives detailed specifications
Quantity
Estimated
Amount
01
01
01
200000=00
60000=00
60000=00
EMD
Amount
4000=00
1200=00
1200=00
SCHEDULE –S.8
S.8.a. LCD Projector
Description
SPECIFICATIONS
Qty
SL. No
01
02
LCD Projector
CEILING MOUNT KIT
Brightness: 5000 ANSI Lumens
Contrast (Full On/Off) : 2000:1
Variable Iris: Yes
High Brightness:
ANSI Lumens:**, Contrast Ratio: **
High contrast:
ANSI Lumens:**, Contrast Ratio: **
Audible Noise: 36 db,
Economy mode:30 db
Size (cm) (HxWxD) : 10 x 40 x 32
Std. Lens: Focus :Normal, Zoom Normal: 1.70:1
Throw Dist (m) : 1.4 - 9.1
Image Size (cm) : 76 – 762, Digital Zoom :**
Digital Keystone: Horz & Vert, Lens Shift: Horz & Vert,
Warranty: 4 years, Performance: Horizontal-Sync Range 15.0
to 106.0 khZ, V-Sync Range:50 to 120khz
Compatibility: HDTV:720p, 1080i, 1080p/60, 1080p/50, 576i,
1125i
EDTV/480p:yes, SDTV/480i: yes
Component Video: yes, Digital Input: HDMI
Display: Type : 2 cm 3 LCD, Native: 1024*768 pixels
Maximum:1600*1200 pixels, Aspect Ratio:4:3(XGA),
Light Source: Type:245W
UHP, Life:2500 hours,
Eco. Life:5000 hours, Speakers: 16 w mono,
Max. Power:380 w, Voltage:100-240 Volts,
Special: Closed captioning, Black board mode, RS 232 port,
USB Port, Wired Networking
Joint for titling the unit upto 10 horizontally 20 vertically
01
01
Various distance elements to level the projector bottom
Metallic silver,
with all mounting screws
Internal cable channel
03
White board
Ferrite Cores
01
Double shielded (foil and braided)
Quality HP-15 connectors
Molded connectors
Easy to use screws caps
Lengths from 1’ to 100’
Male-to-Male or Male-to-Female ends
3 Analog & 8 signal connectors
04
Wireless Presenter
Built-in slideshow buttons
01
50-foot effective range with 2.4 GHz wireless technology
Red laser pointer with LED indicator
Plug-and-play, no software required
Storable receiver and carrying case
Battery-power indicator
05
Interactive
Board
Writing
06
S.8.b. LCD Projector
On/Off switch
With all necessary connections to the kit
VGA CABLES- 20Mtrs Video Cables – 20 Mtrs, HDMI
Cable- 20 Mtrs, VGA/ Video Patch Plates, HDMI Patch
Plate, Installation, Carry bag, Testing kit with all
requirements
Complete installation.
01
SL. No
01
Description
LCD Projector
SPECIFICATIONS
Brightness: 3000 ANSI Lumens
Contrast (Full On/Off) : 2000:1
Variable Iris: Yes
High Brightness:
ANSI Lumens:**, Contrast Ratio: **
High contrast:
ANSI Lumens:**, Contrast Ratio: **
Audible Noise: 36 db,
Economy mode:30 db
Size (cm) (HxWxD) : 10 x 40 x 32
Std. Lens: Focus :Normal, Zoom Normal: 1.70:1
Throw Dist (m) : 1.4 - 9.1
Image Size (cm) : 76 – 762, Digital Zoom :**
Component Video: yes, Digital Input: HDMI
Display: Type : 2 cm 3 LCD, Native: 1024*768 pixels
Maximum:1600*1200 pixels, Aspect Ratio:4:3(XGA),
Light Source: Type: 245W
UHP, Life:2500 hours,
Eco. Life:5000 hours, Speakers: 16 w mono,
Max. Power:380 w, Voltage:100-240 Volts,
Special: Closed captioning, Black board mode, RS 232 port,
USB Port, Wired Networking.
Hanging wall mounted Screen
CEILING MOUNT KIT
Joint for titling the unit upto 10 horizontally 20 vertically
3 Analog & 8 signal connectors
Video Cables – 20 Mtrs, HDMI Cable , 1.4 a - 20 Mtrs,
VGA/ Video Patch Plates and HDMI Patch Plate
Installation, Carry bag, Testing kit with all requirements Complete installation.
Qty
01
S.8.c. LCD Projector:
SL. No
01
Description
LCD Projector
SPECIFICATIONS
Brightness: 5000 ANSI Lumens
Contrast (Full On/Off) : 2000:1
Variable Iris: Yes
High Brightness:
ANSI Lumens:**, Contrast Ratio: **
High contrast:
ANSI Lumens:**, Contrast Ratio: **
Audible Noise: 36 db,
Economy mode:30 db
Size (cm) (HxWxD) : 10 x 40 x 32
Std. Lens: Focus :Normal, Zoom Normal: 1.70:1
Throw Dist (m) : 1.4 - 9.1
Image Size (cm) : 76 – 762, Digital Zoom :**
Digital Keystone: Horizontal & Vertical, Lens Shift: Horizontal &
Vertical
Warranty: 4 years, Performance: Horizontal-Sync Range 15.0 to
106.0 khZ, V-Sync Range:50 to 120khz
Compatibility: HDTV:720p, 1080i, 1080p/60, 1080p/50, 576i,
1125i
EDTV/480p:yes, SDTV/480i: yes
Component Video: yes, Digital Input: HDMI
Display: Type : 2 cm 3 LCD, Native: 1024*768 pixels
Maximum:1600*1200 pixels, Aspect Ratio:4:3(XGA),
Light Source: Type: 245W UHP, Life: 2500 hours,
Eco.
Life:5000 hours, Speakers: 16 w mono,
Max. Power:380 w, Voltage:100-240 Volts,
Special: Closed captioning, Black board mode, RS 232 port, USB
Port, Wired Networking.
Remote operated projector for On/Off and Display adjustments
02
MOTORISED SREEN
03
CEILING MOUNT KIT
04
VGA CABLES- 20Mtrs
05
Video Cables – 20 Mtrs, HDMI Cable , 1.4 a - 20 Mtrs, VGA/ Video Patch Plates and HDMI Patch
Plate
Built-in slideshow buttons
Wireless Presenter
06
07
08
Interactive Writing Board
Peaceful and smooth Tubular Motor, Heat, Protection System which prolongs
Motor's lifetime.
Synchronous Motor: 110-220VAC 50Hz. Octagonal Steel Housing.
High- quality screen which offers clear and vivid picture.
IR and RF are available. Changing the traditional control ways which makes it easy
to operate.
Joint for titling the unit up to +/- 35° horizontally & vertically. Various distance
elements to level the projector. Bottom frame Metallic silver, with all mounting
screws and Internal cable channel
Ferrite Cores
Double shielded (foil and braided)
Quality HP-15 connectors
Molded connectors
Easy to use screws caps
Lengths from 1’ to 100’
Male-to-Male or Male-to-Female ends
3 Analog & 8 signal connectors
50-foot effective range with 2.4 GHz wireless technology
Red laser pointer with LED indicator
Plug-and-play, no software required
Storable receiver and carrying case
Battery-power indicator
On/Off switch
With all necessary connections to the kit
Installation, Carry bag, Testing kit with all requirements Complete installation.
ABSTRACT OF SCHEDULE –S.9
PAO system & Mike Set with sound system
Schedule
No
S.9 (a)
S.9 (b)
Name of the Equipment
PAO System
Mike Set with sound system
Following page gives detailed specifications
Quantity
Estimated
Amount
02
01
100000=00
40000=00
EMD
Amount
2000=00
800=00
SCHEDULE –S.9 (a)
S.9 Item: PAO System
SL.
No
01
Powered Speakers
Frequency Range (-10 dB): 39 Hz -20 kHz (EQ in ‘Flat’ position)
Frequency Response (±3 dB): 42 Hz - 18 kHz (EQ in ‘Flat’ position)
Coverage Pattern: 100° H x 60° V nominal
Directivity Index (DI): 9 dB
Directivity Factor (Q): 8
Crossover Frequency: 2.2 kHz
System Power Rating: 450 W continuous, 900 W peak
LF Power amp: 350 W continuous at driver impedance
HF Power amp: 100 W continuous at driver impedance
02
03
Brackets for speakers
12 Channel Mixer
Customised / tiltable
04
Wireless Hand Mike
05
Collar Mike
06
Podium Mike
07
08
Speaker cable
Connectors & Other
Interconnects
AV Rack
09
Description
SPECIFICATIONS
FrequencyCentre – 125, 250,500,1K, 2K, 4K, 8K
Gain - += 15db
Usb – format usb 1.1
VHF
Band
frequency
Quartz
Lock
Control.
•
Operating
Frequency
Range:
160-245
MHz
•
Single
Channel
Non-Diversity
Receiver.
•
Output:
Balanced
XLR
/
Unbalanced
1/4”
phone
jack.
•
Frequency
Response
:
50Hz
15Hz
• Transmitter Battery Type: 9 V Alkaline
UHF
Band
frequency
Quartz
Lock
Control.
Operating Frequency Range: 720-865MHz.
Single
Channel
Non-Diversity
Receiver.
Output:
Balanced
XLR
/
Unbalanced
¼
phone
jack.
Frequency Response: 50Hz - 15kHz
Frequency Response: 50KHz to 17 Hz,
Dynamic Range(Typical) 96.2 dB to 100dB at 0 gain
Signal to noise ratio
Cardioids:66.0 dB, Super cardioids:67.5dB
Max. Input sound Level:
Cardioids:124.2 dB, Super cardioids:122.7dB
All Values:+6dB at 0 gain
Power Requirements: 11-52 V DC phantom, 2.0 mA,
Output Impedance:180 ohms actual
powered
Qty
04 Nos
04 No
01 No
02 Nos
02 Nos
01 No
60 Mtrs
8 Nos
Height:
890 mm
Width:
530 mm
Depth:
530 mm
SCHEDULE –S.9 (b)
S.9 Item: Mike set with sound system Specifications: Schedule no- 7
Mike set with sound system - specifications
Quantity required – 1
Sound system with amplifier –
a) Amplifier (dual channel) – SSA – 160 Watts
b) Speakers (quantity – 6); 30 Watts
c) Frequency range – 80 Hz – 20 KHz
d) Snesitivity (1 W – 1M) – 86 dB+/- 2 db
e) Impedance (100 V)- 330/670/1.33 KΏ
f) Power capacity – 30/15/7.5 W
g) Collar mike – Micel – 11, frequency – 220 – 600 mhz
h) Receiver – frequency 200.600 Mhz
i) Wireless – microphone – Dynamic VHF
j) Receiver- frequency 239.3320 MHz
01 No
SCHEDULE –F.1
Computer Table
Schedule
No
F.1
Name of the Equipment
Computer Table
Following page gives detailed specifications
Quantity
Estimated
Amount
110
500000=00
EMD
Amount
10000=00
SCHEDULE –F.1
Computer Table
Specifications of Computer Tables
Note:
S.No. Item
1
Make and Model
Specifications
To be Specified by the vendor
2
3
Length
Width
3 ft
2.5 ft
4
Height
5
Price
2.5 ft
Inclusive of all taxes and should include
transportation and fitting charges at customer site.
1.Plank with slider and locking system for placing keyboard and mouse
2. Provision in the form of plank for placing CPU at the bottom of the table
should be provided.
ABSTRACT OF SCHEDULE –F.2
Computer Chair
Schedule
No
F.2
Name of the Equipment
Computer Chair
Following page gives detailed specifications
Quantity
Estimated
Amount
110
330000=00
EMD
Amount
6600=00
SCHEDULE –F.2
Computer Chair
Specifications
S. No.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Computer Chairs
Item
Specifications
Type
Revolving Chair with super quality castor twin
nylon wheels
Arm Rest
arm rest wide enough and comfortable for placing
hands
Seat height
Adjustable - Min: 8cm, Max: 16cm,
Total height
Min: 100cm, Max:113cm
Rear rest
50cm
Area of seat rest
47 cm x 46 cm
Area of rear rest
47 cm x 50 cm
Pneumatic height adjustment
At a press of a lever, seat be adjusted to the required
height, provide a cushioning effect
Swivel Mechanism
360 degree lateral movement
Moulded Foam
The seat and back rest are made up of moulded foam
of right density and thickness
Price
Inclusive of all taxes and should include
transportation and fitting charges at customer site
ABSTRACT OF SCHEDULE –F.3
Modular Chairs
Schedule
No
F.3
F.3.a
F.3.b
Name of the Equipment
Modular Chairs
Modular Chairs
Modular chairs
Following page gives detailed specifications
Quantity
Estimated
Amount
EMD
Amount
240
300
720000=00
900000=00
14400=00
18000=00
SCHEDULE –F.3
F.3.a. Modular Chair Specification:
Back support height: 2ft, MS pipe 1” hallow round pipe, Flat patti: 17×2 mm (5 Supports)
Poly urethane moulded foam: Height: 24”, Widhth:18.5”, Thickness :3.5”, Sound proof cloth cover 7 mm
thickness with double color,
Backside cover: PVC fiber 24” ×18.5” with suitable thickness
Back fix:4 bolts
Chair seat:
Frame: 18” ×18” with (40 mm ×20 mm) hollow tube on top of it 4 mm hard board with two supports.
Poly urethane moulded foam seat : 18” ×18”, cushion thickness 2”.
Seat Fix: 16 gauge back brackets (Four bolts)
Sound proof cloth cover 7 mm thickness with double color.
F.3.b. Modular Chair Specifications:
Seat are made of rubber fitted on molded plywood of 12 mm thickness
Foam, The chair is made of 25.4mm (1 Inch) and the gage of pipe is 2 MM that is 14 gage
High :-865 mm,
Width :-720 mm,
Depth :-540 mm
ABSTRACT OF SCHEDULE –F.4
Executive Chairs
Schedule
No
F.4
F.4.a
F.4.b
F.4.c
F.4.d
Name of the
Equipment
Quantity
Estimated
Amount
30
30
25
30
150000=00
150000=00
100000=00
99000=00
Executive Chairs
Executive Chairs
Executive Chairs
Executive Chairs
Executive Chairs
Following page gives detailed specifications
EMD
Amount
3000=00
3000=00
2000=00
1980=00
SCHEDULE –F.4
Executive Chairs
E.4.a. Executive Chairs Specifications:
Body Line High Back
Jumbo base with nylon castors, Auto seat height adjustable, Tilting Mechanism with single position,
Spring tension control adaptable to body weight, Moulded cushion that provides additional support,
Lumber support and contoured back poly Uthin Armset.
12mm thick hot pressed revolving Chair with chrome base. Cushion seat and back PU. High back.
Having one touch gas adjustment feature to suit varying height push back mechanism.
Poly urethane moulded foam: Height:24”, Widhth:18.5”, Backside cover: PVC fiber 24” ×18.5” with suitable
thickness
Chair seat:
Frame: 18” ×18” with (40 mm ×20 mm)hollow tube on top of it 4 mm hard board with two supports.
Poly urethane moulded foam seat : 18” ×18”, cushion thickness 2”.
Sound proof cloth cover 7 mm thickness with double color.
E.4.b. Executive Chairs Specifications:
The chair is of Fixed Back Model Single seat & Black, leatherite Upholstery with high density foam
Chrome Plated steel Base of 12 gage and SS Coated pipe
Height :- 925
Width :- 570
Depth :- 720
E.4.c. Executive Chairs Specifications:
The Chair is made of netted Back, Lethe rite seat, Pu Foam, Extra Pressure Springs, Pu Adjustable
Arm rests, Tilt Mechanism, Center tilt Mechanism with Allows infinite variation of height
adjustment
High
Width
Depth
:- 940-830mm
:- 590 mm
:- 630 mm
E.4.d. Executive Chairs Specifications:
Polyurethane Molded Cushion ,with fixed cotton Cloth (Preferable color cloth), 40 density for seat and
30 density for back rest, round CRC 14 gage thickness of pipe, 40/50 Microns powder coated paint,
High :-830 mm
Width :-545 mm
Depth :-600 mm
ABSTRACT OF SCHEDULE –F.5
Acoustic system deign
Schedule
No
F.5
F.5.a
F.5.b.
Name of the Equipment
Estimated
Amount
EMD
Amount
Acoustic system design for Seminar
halls
Acoustic system design (EEE)
Acoustic System design (ME)
250000=00
250000=00
5000=00
5000=00
Following page gives detailed specifications
SCHEDULE –F.5
E.5.a: Acoustic System Design Specifications:
Sl. No
1.
2.
3.
4.
5.
Description
POWERED LED LIGHT FITTINGS 9W LED
Rope Lights + 4 CFL
POP (Fall Ceiling)
Acoustic Carpet
Installation
SPECIFICATIONS
Include wiring cost
2400Sqft
2400Sqft
Testing ,commissioning ,training and installation
Qty
18
04
----
E.5.b.Acoustic System Design specifications:
SL.No
01
Description
Powered Speakers
02
03
Brackets for speakers
12 Channel Mixer
04
Wireless Hand Mike
05
Collar Mike
06
Podium Mike wireless
07
08
Speaker cable
Connectors & Other
Interconnects
AV Rack
09
10
11
12
13
POWERED
LED
LIGHT FITTINGS 9W
LED
Rope Lights + 4 CFL
POP (Fall Ceiling)
Acoustic Carpet
SPECIFICATIONS
Frequency Range (-10 dB): 39 Hz -20 kHz (EQ in ‘Flat’ position)
Frequency Response (±3 dB): 42 Hz - 18 kHz (EQ in ‘Flat’ position)
Coverage Pattern: 100° H x 60° V nominal
Directivity Index (DI): 9 dB
Directivity Factor (Q): 8
Crossover Frequency: 2.2 kHz
System Power Rating: 450 W continuous, 900 W peak
LF Power amp: 350 W continuous at driver impedance
HF Power amp: 100 W continuous at driver impedance
Customised / tiltable
FrequencyCentre – 125, 250,500,1K, 2K, 4K, 8K
Gain - += 15db
Usb – format usb 1.1
VHF
Band
frequency
Quartz
Lock
Control.
• Operating
Frequency
Range:
160-245
MHz
• Single
Channel
Non-Diversity
Receiver.
• Output:
Balanced
XLR
/
Unbalanced
1/4”
phone
jack.
• Frequency
Response
:
50Hz
15Hz
• Transmitter Battery Type: 9 V Alkaline
UHF
Band
frequency
Quartz
Lock
Control.
Operating Frequency Range: 720-865MHz.
Single
Channel
Non-Diversity
Receiver.
Output:
Balanced
XLR
/
Unbalanced
¼
phone
jack.
Frequency Response: 50Hz - 15kHz
Frequency Response: 50KHz to 17 Hz,
Dynamic Range(Typical) 96.2 dB to 100dB at 0 gain
Signal to noise ratio
Cardioids:66.0 dB, Super cardioids:67.5dB
Max. Input sound Level:
Cardioids:124.2 dB, Super cardioids:122.7dB
All Values:+6dB at 0 gain
Power Requirements: 11-52 V DC phantom, 2.0 mA,
Output Impedance:180 ohms actual
powered
Qty
04 Nos
04 No
01 No
02 Nos
02 Nos
01 No
120 Mtrs
12 Nos
Height: 890 mm
Width: 530 mm
Depth: 530 mm
Include wiring cost
2400Sqft
Himalyan Acoustics ‘APHONY FIBRETTE Ceiling tiles made of
Wood Fibre cement composites 15mm thick with an option of colours
as per the choice of the Architect/ person in charge of size 595x595 .
Has excellent noise absorption of 1.00 NRC as per ISO: 354-1985 and
ASTM 423-90 a, Density 400 Kg/ m3, meets stringent Fire Ratings
ASTM D- 876, weather resistance as per IS 3308, Thermal Insulation
as per IS:3346-1980 with relative humidity of 90% RH at 60o
Celsius(140o Fahrenheit) for 15 days= No deterioration. Conforms to
En 131682001 and are RoHS Complaint. Can be installed on
T24/silhouette t grid system as per the choice of the architect/engineer
specially designed for Acoustic vibration management and long life
with a backing of 50mm HA Absorb Wool (50x500) for excellent results
1256 Sqft.
01 No
18
04
06
ABSTRACT OF SCHEDULE –F.6
Chair with attached Planck
Schedule
No
F.6
Quantity
Estimated
Amount
EMD
Amount
30
150000=00
3000=00
Name of the Equipment
Chair with attached Planck
Following page gives detailed specifications
SCHEDULE –F.6
CHAIRS WITH WRITING PAD Specifications:
Specifications:1) Size: 54X61X80CM
2) Stackable, plastic back cover.
3)1.0MM tube thickness
4) fabric or PU surface
ABSTRACT OF SCHEDULE –F.7
Modular Furniture for 30 computers (Computer Chair + Table + Partition work)
Schedule
No
F.7
Quantity
Estimated
Amount
EMD
Amount
30
390000=00
7800=00
Name of the Equipment
Modular Furniture for 30 computers
(Computer Chair + Table + Partition work)
Following page gives detailed specifications
ABSTRACT OF SCHEDULE –F.7
Furniture for 30 computers (Computer Chair + Table + Partition work)
Modular furniture for 30 Desk top systems
(Computer chairs + Computer tables + Partition work)
Computer Chairs
Chair should has adjustable tilting mechanism which is responsive for body movement.
3600 swivel mechanism and twin wheel castors for free movement.
Modular Computer work stations to house 30 computers
Note: All the dimensions are in mm
 Dimensions given are approximate values. The actual dimensions of a room may vary.
 Modular furniture is required for 30 Computer systems. (In the figure 30 workstations are
shown)
 Partition of glass for separation of each system
ABSTRACT OF SCHEDULE –F.8
Tables (Laboratory Tables)
Schedule
No
F.8
Name of the Equipment
Laboratory Tables
Following page gives detailed specifications
Quantity
24
Estimated
Amount
288000=00
EMD amount
5760=00
SCHEDULE –F.8
Laboratory Tables for Labs
Specifications:
S. No
1
2
3
Specifications
Length-6f
Width-4f
Height-2.5f
Iron pipe dimension are: Sq-pipe 1 ½” & 16 guage thick with plastic bushes with all iron is powder
coated painted, Standard conditions should be included along with above specifications.
ABSTRACT OF SCHEDULE –F.9
Laboratory Stools
Schedule
No
F.9
Name of the Equipment
Laboratory Stools
Following page gives detailed specifications
Quantity
96
Estimated
Amount
144000=00
EMD
Amount
2880=00
SCHEDULE –F.9
Laboratory stools for Labs
Specifications:
S. No
1
2
3
Specifications
Length-1.5f
Width-1.5f
Height-2f
Iron pipe dimension are: 1” sq-pipe with 16 16 guage thick with plastic bushes with all iron is powder
coated painted, Standard conditions should be included along with above specifications.
ABSTRACT SCHEDULE –F.10
Table with Electrical Plug points, lockers, racks, acid proof sheets
Schedule
No
F.10
Name of the Equipment
Quantity
Table with electrical plug points,
lockers, racks, acid proof sheets
06
Following page gives detailed specifications
Estimated
Amount
168000=00
EMD Amount
3360=00
SCHEDULE –F.10
Table with Electrical Plug points, lockers, racks, acid proof sheets
Specifications:
S.No
1
2
3
4
5
Specifications
Acid proof sheet for the tables (6 X 4 feet)
Racks for keeping chemicals (6 X 2 feet)
Lockers for 2 keys
Racks for keeping Stock solutions.
Electrical plugs 2 (15 Amps)
ABSTRACT SCHEDULE –F.11
Seminar hall chairs
Schedule
No
F.11
Name of the Equipment
Seminar Hall Chairs
Following page gives detailed specifications
Quantity
100
Estimated
Amount
500000=00
EMD Amount
10000=00
SCHEDULE –F.11
Seminar hall chairs specifications:
Item – Seminar Hall chairs
Specifications:
1
Seat Pan width
2
Seat Back Height
3
Seat Back Width
4
Seat Back Tilt
18”-20” with a waterfall sloping front edge.
minimum 14”
12” - 15”
8
adjustable 0-15 degrees
5
6
7
7
8
9
Arm rest height
Padding
Gauge of supporting rods
Make & Model
Delivery
Seat and backrest
Minmimum 7 “
seat pan, backrest and armrests
Min 1mm
Should be specified by the vendor
At the customer site
Cushion/puff type
ABSTRACT SCHEDULE –F.12
Class Room Boards Green
Schedule
No
F.12
Name of the Equipment
Class Room Boards Green
Following page gives detailed specifications
Quantity
07
Estimated
Amount
42000=00
EMD Amount
840=00
SCHEDULE –F.12
Class room boards green
Specifications
Height
Width
Colour
Type
Clamps
Delivery
Price
4 ft
12 ft
Green
Chalk writeable
Yes
At the customer site
Inclusive of all the taxes and should include
transportation and installation is at the risk
of the suppliers charges
ABSTRACT SCHEDULE –F.13
3-seater Desks
Schedule
No
F.13
Name of the Equipment
3-seater Desks
Following page gives detailed specifications
Quantity
60
Estimated
Amount
600000=00
EMD Amount
12000=00
SCHEDULE –F.13
3-seater Desks
Specifications:
Specifications
Width
Seat width
Bookshelf height
Supporting material
Seat height
Seat material
Delivery
Price
Back rest height
Seat length
3’ 10’’
1’ 2”
2’10’’
powder coated iron – width – 1”
1’6’’
Wooden
At the customer site
Inclusive of all the taxes and should include
transportation charges
8“
3’ 9”
ABSTRACT SCHEDULE –F.14
Podium
Schedule
No
F.14
Name of the Equipment
Podium
Following page gives detailed specifications
Quantity
04
Estimated
Amount
40000=00
EMD Amount
800=00
Schedule- F.14
Podium Specifications:
Height front
Height backside
Width
Podium hand rest width
Material
Thickness of Material
Delivery
47 “
3’ 9’’
23’’
23’’
Wooden
Minimum 1”
At the customer site
ABSTRACT SCHEDULE –F.15
Dias
Schedule
No
F.15
F.15.a
F.15.b
Name of the Equipment
Dias
Dias
Dias (3 class rooms + 4)
Following page gives detailed specifications
Quantity
02
07
Estimated
Amount
70000=00
210000=00
EMD Amount
1400=00
4200=00
Schedule no – F.15
F.15.a. Dias Specifications:
Sl. No
1.
Description
Dias
SPECIFICATIONS
Length 15 Feet, Width 12 Feet Height 1.5 feet with two steps at
each side
Gurgen Plywood of 18 inch (Water Proof)
Podium of gurgen plywood with three racks 5 feets (Angle curved at
top glass fitted
F.15.b. Dias Specifications:
Specifications – class room
Height
Length
1‘
Width
Material
Delivery
Specifications – Seminar hall
7 ‘(quantity -1) , 8’ (quantity – 2)
Hollow wooden
At the customer site
Height
Length
1 ‘ 6”, with one step
Width
Material
Delivery
12 ‘
Hollow wooden
At the customer site
20 ‘
20 ‘
ABSTRACT SCHEDULE –F.16
Notice Board
Schedule
No
F.16
Name of the Equipment
Notice Board
Following page gives detailed specifications
Quantity
Estimated
Amount
EMD
Amount
06
60000=00
1200=00
SCHEDULE –F.16
Notice boards
Width
Height
Type
Clamps
12 ‘
4’
Pin cushion
Wall clamps
ABSTRACT SCHEDULE –F.17
Group discursion Table
Schedule
No
F.17
Name of the Equipment
Group Discussion Table
Following page gives detailed specifications
Estimated
Amount
EMD Amount
Quantity
01
30000=00
600=00
SCHEDULE –F.17
Group Discussion table Specification:
Group Discussion table with out chairs should be made out of 25mm thick PLB top with duck nose
edges. The table is to be arranged in “U” shape as shown in drawing with table overall size 1200X600
mm. It should have appropriate connecting tops with duck nose edges. The under structure should be
made with 16mm PLB.
ABSTRACT OF SCHEDULE –F.18
Lab working table
Schedule
No
F.18
Name of the Equipment
Lab working table
Following page gives detailed specifications
Quantity
Estimated
Amount
EMD
Amount
05
300000=00
6000=00
SCHEDULE –F.18
Lab Working Table
1. Table dimension
: 3600 x 1500 x 900 mm (l x b x h)
2. Materials for table construction
a) Table top: The table top shall be made of finely polished 18 mm ±1 mm thick
black Colour Granite with rounded edges.
b) Under bench modules:
i) Shall be made up of 20 gauge pretreated Galvanished iron
Sheet and completely finished with epoxy powder coating.
ii) Modules shall be provided with top drawer and bottom
cupboard with horizontal removable inner partition and
with lockable doors and aesthetic stainless steel handles
iii) The under-bench modules will be arranged alternatively,
keeping sufficient space in between for knee space. The
base of the modules will be provided with skirting panels
for aesthetic look.
iv) Sink with swan neck tap and waste pipe up to end of lower c)
Quantity of modules: Modules as per drawing on both side of table (3 Nos. each side)
d) Quantity of Knee Hole Space : As per drawing (2 Nos each side of total 4 Nos.)
e) Reagent racks: Three Nos. of two tier Reagent Rack each with 2 Nos. of electrical point
per side on the table as per drawing
f) Colour: Colour combination of IVORY and drawer fronts contrasting ORCHID BLUE for
aesthetic appeal by powder coating technique.
ABSTRACT OF SCHEDULE –F.19
Single Bed cot with racks
Schedule
No
F.19
Name of the Equipment
Single Bed cot with racks
Following page gives detailed specifications
Quantity
Estimated
Amount
EMD
Amount
350
2250000=00
45000=00
SCHEDULE –F.19
Single Bed Cot with racks
Specifications of Single Bed Cot with racks
S.No. Item Perticulars
Specifications
1
Size
75” x 30”
Frame
Head rest Pipe
Plywood
40 x 40 x 1.60 mm Square MS CRCA pipe.
20 x 1.6 mm MS CRCA
72” x 30” plywood having thickness of 25mm
manufactured by ISO9001 certified company duly
supported by cross bars.
Alkid Amino Liquid paint in desired shade should be
duly oven backed.
Paint
Storage :
(a) Shelf of Size
900(w) x 450(d) x 450(h) mm with front panel as
shown in drawing.
(b)Storage unit of 2 doors 900(w) x 450(h) mm (Space divided into 2
made of MS Sheets with compartments).Lockable 2 doors (external locking)
partition
should
have
provision for pad lacking
dimensions:
Note:
1.The Price quoted
customer’s site.
should
include
transportation
and
installation
*** Vendor is requested to visit the customer site before giving the quotation.
charges
at
ABSTRACT OF SCHEDULE –F.20
Reading Table
Schedule
No
F.20
Name of the Equipment
Reading table
Quantity
Estimated
Amount
EMD
Amount
250
600000=00
12000=00
Total Estimated Amount Rs.600000=00
Following page gives detailed specifications
SCHEDULE –F.20
Reading Tables
Specifications of Reading Tables
S.No. Item
1
Make and Model
Specifications
To be Specified by the vendor
2
3
Length
Width
3 ft
2 ft
4
Height
5
Price
2.5 ft
Inclusive of all taxes and should include
transporatation and fitting charges at customer site.
Note:1. 1” hollow round M S pipe with 16 gauge and plate is 16 G thick ness.
2. Detailed specifications as per the sheet enclosed.
ABSTRACT OF SCHEDULE –F.21
S-Type Chairs
Schedule
No
F.21
Name of the Equipment
S-Type Chairs
Quantity
Estimated
Amount
EMD
Amount
250
225000=00
4500=00
Total Estimated Amount Rs.225000=00
Following page gives detailed specifications
SCHEDULE –F.21
S Type Chairs
Specifications of S type Chairs
S.No. Item
Specifications
1
Type
2
Arm Rest
11
Price
S-type- all made with Iron, Back and Front Iron
plate(16 gauge), Pipe-16 gauge.
Arm rest wide enough and comfortable for placing
hands.
Inclusive of all taxes and should include
transporation and fitting charges at customer site.
1” hollow round M S pipe with 16 gauge. Detailed
specifications as per the sheet enclosed.
ABSTRACT OF SCHEDULE –F.22
Furniture for lab
Schedule
No
F.22
Estimated
Amount
EMD Amount
200000=00
4000=00
Name of the Equipment
Furniture for Lab
 MODULAR Wall BENCH (IN ‘u’ SHAPE
 MODULAR island BENCH
 wall mounted storage unit
Following page gives detailed specifications
SCHEDULE –F.22
Furniture for lab
F-22: Item
:
Furniture for the lab (Lab tables with fittings)
MODULAR WALL BENCH (IN ‘U’ SHAPE) – AS PER THE DIAGRAM
DIMENSION
( 49 L X 2 . 5 B X 2 . 8 H ) FEET
M. O. C.
EPOXY POWDER COATED CRCA MODULES
EXTERNAL FINISH
EPOXY POWDER COATED.
INTERNAL FINISH
EPOXY POWDER COATED.
WORKING SURFACE
19 MM THICK POLISHED GRANITE WITH MOULDED EDGES
BOTTOM ARRANGEMENTS
12 NOS. MODULE, EACH OF 2 . 5 FEET. LENGTH WITH 2 SHUTTERS,
ONE INTERNAL SHELVE .
ELECTRICAL POINTS
5 / 15 A SOCKETS ON BENCH - 16 NOS. ON PANEL BOX FLEXIBLE
COLOUR
FITTING AS PER REQUIREMENT POSITION
STANDARD COLOUR
MODULAR ISLAND BENCH - AS PER THE DIAGRAM
DIMENSION
M. O. C.
EXTERNAL FINISH
INTERNAL FINISH
BOTTOM ARRANGEMENTS
WORKING SURFACE
COLOUR
ELECTRICAL POINTS
( 11 L X 4 B X 2 . 8 H ) FEET.
EPOXY POWDER COATED CRCA MODULES
EPOXY POWDER COATED.
EPOXY POWDER COATED.
06 NOS. MODULE, EACH OF 2 . 5 FEET. LENGTH WITH 2 SHUTTERS, 1
DRAWER AND ONE INTERNAL SHELVE.
19 MM THICK POLISHED GRANITE WITH MOULDED EDGES
STANDARD COLOUR
5 / 15 A SOCKETS ON BENCH - 12 NOS. ON PANEL BOX , FLEXIBLE
FITTING AS PER REQUIREMENT POSITION
WALL MOUNTED STORAGE UNIT – 2 NOS.
DIMENSION
M. O. C.
EXTERNAL FINISH
INTERNAL FINISH
DOORS
COLOUR
( 6 L X 1 . 5 B X 2 H ) FEET
EPOXY POWDERCOATED CRCA.
EPOXY POWDER COATED.
EPOXY POWDER COATED.
OPAQUE OPENABLE TYPE
IVORY / BLUE
Note:
The stating wall bench from the entry door should consists of suitable Plank with slider and locking
system for placing keyboard and mouse and the bottom should have Provision in the form of racks for
placing CPU at the bottom of the table. The bench should be provided with necessary electrical fitting
for the computer systems and the printer.
Conditions:
1.
Price
2.
3.
4.
Installation
Commissioning
Demonstration
warranty
Inclusive of all taxes and should include transportation and
fitting charges at customer site.
At customer site
and The supplier should make necessary satisfactory
commissioning of the tables with necessary fittings.
Must supply warranty of the fittings (as applicable)
JNTUA COLLEGE OF ENGINEERING
PULIVENDULA-516390, Y.S.R. District, A.P
Rc.No. JNTUA/CEP/Tender Notice-2/2012
Date: 05.05.2012
TENDER NOTICE
Sealed tenders are invited from the reputed dealers/suppliers for the supply
of different Lab Equipments/Softwares/Computers, Projectors/ UPS/ Air
Conditioners/ Furniture (Computer Chairs & Tables, Seminar Hall Chairs, 3seater Desks, Single Bed Cots, Reading Tables, etc.) for JNTUA College of
Engineering, Pulivendula, YSR dt,, A.P
Details of the tender can be obtained from the undersigned from 04.05.2012
on payment of Rs. 2,000/- + 12.5% Sales Tax (Non-refundable) in the form of
Demand Draft payable at Pulivendula in favour of The Principal, JNTUA
College of Engineering, Pulivendula (A.P.) drawn on any nationalized
bank, not before 05.05.2012. The tender document can also be downloaded
from website www.jntua.ac.in.The sealed tenders should reach the
undersigned on or before 28.05.2012 by 4:00 pm.
Sd/--- PRINCIPAL