HMT (INTERNATIONAL) LIMITED
A Govt. of India Undertaking
(OPEN TENDER)
BID DOCUMENTS
FOR SUPPLY, INSTALLATION & COMMISSIONING, TRIAL OF
Pillar Drilling Machine, Pedestal Drilling Machine, Welding Equipment, Electrical &
Electronic Trainers, Electrical Appliances, Electrical & Electronic Equipment, Electrical
Meters
For
Upgradation & Modernisation of Rajiv Gandhi School of Production and Art,
Ulaanbaatar, Mongolia – Phase – II
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated 27-10-2014
CLOSING ON: 18-11-2014, TIME 14.00 HRS
TECHNICAL BID OPENING ON: 18-11-2014 TIME 14.30 HRS
PLACE: HMT(I) Board Room, HMT Bhavan,No.59, Bellary Road, Bangalore.
The Tender document issued against payment of Rs 2,500.00 (Rupees Two Thousand Five Hundred only) in
the form of a Demand Draft towards cost of tender document. The Bidder who choose to download tender
document from website must submit the Demand Draft towards cost of the Tender documents along with
Technical bids in Envelope-I.
1.
2.
3.
4.
5.
ATTENTION
Only sealed Tenders shall be entertained. All joints of envelope should be
sealed with wax or with cello tape to ensure it is tamper proof.
Tenders not sealed shall be rejected straight away.
Do not use window envelope.
Lot-wise Technical Bid and Commercial Bid to be put in a separate cover superscribing Tender Ref. No., Date, Submission date, Lot number and Bidder address
on the top of envelope.
The Bidder may depute their authorized representative to witness the tender
opening for both Technical and Commercial Bids.
HMT Bhavan, No.59, Bellary Road, Bangalore 560 032
Tel: 91- 80- 2333 9060, Fax: 91- 80- 2333 9048 / 2333 9286
Web Site: www.hmti.com E-mail:contactus@hmti.com
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 1 of 115
INDEX
SECTION I : INVITATION FOR BIDS(IFB)
1.
Invitation
2.
Contact Information
3.
Two Bid System
4.
Date of Submission and opening of Technical Bid
SECTION II: INSTRUCTIONS TO BIDDERS (ITB)
1.
Definitions and Interpretation
2.
Compliance of Requirements
3.
Place of Delivery of Supplies
4.
Criteria for pre qualification of Bidder
5.
Cost of Bid documents
6.
Earnest Money / Bid Guarantee
7.
8.
9.
10.
11.
12.
13.
14.
15.
Period of Validity of Bids
Deadlines for submission of bids
Opening and Evaluation of Bids
Comparison of Bids
Award Criteria
HMT(I) right to amend scope of work
Corrupt & fraudulent practices
Interpretation of the clauses in the tender document
General
SECTION III: SPECIAL CONDITIONS OF CONTRACT (SCC)
1.
Execution
2.
Colour
3.
Electricals
4.
Delivery period
5.
Inspection, Re-Inspection & Acceptance
6.
Packing
7.
Port of Shipment / Discharge
8.
Freight & Insurance
9.
Consignee
10.
Invoice to
11.
Price
12.
Payment Terms – For Supplies
13.
Payment Terms – For Services Portion
14.
Penalty for Delayed Supplies
15.
Clearance for Despatch
16.
Name & Address of the Shipping Agent
17.
Technical Documents
18.
Bought Outs
19.
Rejection & Risk
20.
Performance Bank guarantee
21.
International Warranty
22.
Erection & Commissioning
23.
Arbitration
24.
Jurisdiction
25.
Force Majeure
SECTION IV: SCHEDULE OF REQUIRMENTS / SCOPE OF SUPPLY (SR)
SECTION V: COMMERCIAL
Annexure – 1
Price Schedule
Annexure – 2
Proforma for statement of deviations from Tender conditions
Annexure – 3
Proforma for Commercial details & previous experience
Annexure – 4
Proforma for Performance Bank Guarantee
Annexure – 5
Proforma for Vendor Appraisal
Annexure – 6
Proforma for Vendor Registration
Annexure – 7
Proforma for Bank Guarantee for Bid Guarantee
Annexure – 8
Qlity and Packing details
Enclosure-1
Detailed Technical Specifications
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 2 of 115
SECTION I: INVITATION FOR BIDS (IFB)
1.
HMT (International) Ltd, [HMT (I)] Bangalore invites sealed bids from eligible Indian bidders for supply,
installation, commissioning, Trial of following items for Upgradation & Modernisation of Rajiv Gandhi School of
Production & Art, Ulaanbaatar, Mongolia – Phase II as per Schedule of Requirements / Scope of Supplies (SR) (Section IV)
Sl.No
1
2
3
4
5
6
7
LOT Reference
LOT – 1
LOT – 2
LOT – 3
LOT – 4
LOT – 5
LOT – 6
LOT – 7
ITEM
Machine Tools – Pillar & Pedestal Drilling Machines
Welding Equipment
Electrical Machine Trainers
Electrical Appliances
Electrical & Electronic Equipment
Electronic Trainers
Electrical Meters
HMT(I) invites sealed bids from eligible bidders for the Supplies as above with details listed in Section IV.
Part bidding among the Lots is allowed and Part bidding within the lot is not allowed. Bidders shall quote for all
the items within the lot.
2.
Contact information
The General Manager, Projects
HMT (International) Limited,
59, Bellary Road, Bangalore-560032, INDIA
Tel No.: 080- 23339060
Fax No.: 080- 23339048 / 23339286
E-mail: contactus@hmti.com / ksridhar@hmti.com
3.
Two bid System
The two bid system will be followed. The bidder must submit his offer in two separate sealed envelopes as
explained below:
Offer in the prescribed forms Section – V, Annexure 1 to 8 should be submitted in the following manner.
Envelope I: “Technical bid”: The sealed envelope shall contain all the copies of Lot-wise technical bids together
with Commercial Bids separately without indicating the prices. This envelope shall be clearly marked “Part I Technical bid”, indicating Tender No., Lot Number, Closing Date & Time and bidder address duly filled-in
(separately for each Lot).
The Envelope-I should be duly sealed on all joints with wax or tamperproof sealing using cello tape.
This part shall include / indicate the following:
1.
The Bidder shall provide requisite documentary evidence for pre-qualification criteria as stated below, failing
which, the Bids may result in rejection:
• The Bidder’s average annual turnover for 3 years shall be atleast as mentioned below against each Lot
in the last three financial years.
LOT -1: Rs.10.0 lakh (Rupees Ten lakh only)
LOT -2: Rs.90.00 lakh (Rupees Ninety lakh only)
LOT -3: Rs.5.00 crore (Rupees Five crore only)
LOT -4: Rs.20.00 lakh (Rupees Twenty lakh only)
LOT -5: Rs.10.00 lakh (Rupees Ten lakh only)
LOT -6: Rs.5.00 crore (Rupees Five crore only)
LOT -7: Rs.20.00 lakh (Rupees Twenty lakh only)
- The Total Annual turnover to bid for all the Lots is Rs 1150.00 lakh only (Total Rupees One
thousand One hundred Fifty lakh only).
- The Bidder shall quote for all the Lots or part bid among the lots mentioned under Scope of Supply.
However, part bidding within the lots is not allowed.
- In case, the Bidder quotes for more than one lot, the turn over shall be sum of the value given
against each lots.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 3 of 115
2.
•
The Bidder must have minimum 3 years continuous experience in manufacturing / supply of items
specified in the Scope of Supply. Attach at least one Purchase Order copy of each year separately for
three years.
•
Bidder should submit satisfactory certificate from at least 2 reputed clients to whom similar nature of
supplies have been made.
The Bidder shall submit Earnest Money Deposit as indicated below against each lot in the form of Demand
Draft drawn in favour of HMT (International) Limited payable at Bangalore in separate envelopes for each lot
in the Technical Bid. .
LOT -1:
LOT -2:
LOT -3:
LOT -4:
LOT -5:
LOT -6:
LOT -7:
Rs.5,200/- (Rupees Five thousand Two hundred only)
Rs. 61,400/- (Rupees Sixty One thousand Four hundred only)
Rs. 76,700/- (Rupees Seventy Six thousand Seven hundred only)
Rs. 16,300/- (Rupees Sixteen thousand Three only)
Rs. 7,800/- (Rupees Seven thousand Eight hundred only)
Rs. 80,500/- (Rupees Eighty thousand Five hundred only)
Rs. 13,000/- (Rupees Thirteen thousand only)
- The Total Earnest Money Deposit to bid for all the Lots is Rs.2,60,900/- (Rupees Two lakh Sixty thousand
Nine hundred only)
- The Bidder shall quote for all the Lots or part bid among the lots mentioned under Scope of Supply.
However, part bidding within the lots is not allowed.
- In case, the Bidder quotes for more than one lot, the Earnest Money Deposit shall be sum of the value given
against each lots.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
The bidder must be a manufacturer or an authorized dealer or HMTI vendor.
Technical bids without prescribed cost toward tender cost & EMD in the form of Demand Draft/ Purchase
receipt will be rejected summarily.
Bid documents Purchase Receipt or DD in favour of HMT(I), Bangalore for Rs.2,500/- if tender documents are
downloaded from website.
Duly filled Technical bid for each Lot separately with proper seal and signature of the authorized person on
each page of the bid submitted.
Complete Scope of Supplies with all necessary details and acceptance of commercial terms and conditions as
provided under Section IV & V Lot-wise separately.
Make / Model for each of the item to be specified in the bid and the Catalogues to be enclosed with the
technical bid.
Bids shall be valid for a minimum period of 90 (ninety) days from the last date of submission.
Furnish acceptance for providing Performance Bank Guarantee for 10% of the contract value in the event of
tender being awarded.
Point-wise details for the services/requirements/details required in the bid documents shall be furnished. If
there are any deviations, the same should be clearly specified in Annexure-2 of Section-V.
Self attested copy of VAT registration certificate as applicable.
List of customers both domestic & overseas to whom similar supplies have been provided in the past 3 years
in the prescribed format Section-V, Annexure-3.
Satisfactory certificate from at least 2 reputed clients to whom similar nature of supplies has been rendered.
Vendor Registration form – Section – V, Annexure – 5 duly filled {Only for New Vendors of HMT(I)}.
Copy of ISO-9000 Certificate, if applicable.
Payment Terms. As per clause 13 in Section-III. Specify deviations if any.
A copy of “Un-Priced Section – V, Annexure–1” i.e., a copy of the Price Schedule without the price details.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 4 of 115
Envelope II: “COMMERCIAL BID”: This sealed envelope shall contain price details. This envelope shall be clearly
marked “Part II - Commercial Bid”, indicating Tender No., Date & Time, Lot Number and bidder address duly filled
(separately for each Lot).
The Envelope – II should be duly sealed on all joints with wax or tamperproof sealing using cello tape.
o Prices should be offered in Indian Rupees only. Should furnish break up of price as required in Section V;
Annexure – I. The prices quoted shall be for FOR Chennai Port and considered firm and not subject to any
change.
4.
o
The supplies will be inspected by HMTI by deputing quality assurance personnel to the vendor’s worksite.
Vendors are required to reimburse the Cost of Inspection at 6% of the total order value + Service Tax as
applicable.
o
All prices & other information like discount etc., having a bearing on the prices shall be written both in figures
& words in the prescribed offer form. In the event of difference, the price in words shall be valid and binding.
If any service tax is applicable, the same should be indicated separately.
o
The terms of payment for supplies will be as indicated under clause 13 in Section-III – Terms and conditions of
the tender. The bidder has to accept the payment terms. Any deviation in the payment terms offered shall be
considered and suitable Bank interest of 18% per annum will be loaded for comparison purposes only.
However acceptance of the payment terms indicated by the bidder is subject to approval of HMT(I) Purchase
Committee.
o
The bidder should quote their lowest possible price.
o
L1 shall be decided on Lot price basis.
Date of submission of bids and opening of the Technical bid:
Both the envelopes (Part I & II) Lot-wise shall be put in one cover, duly sealed on all joints with wax or tamperproof
sealing using cello tape and super scribing Tender No., closing date & time, opening date & time, Lot number and
Bidder address.
The envelopes, which are not sealed, will be rejected straightaway/summarily.
The sealed bids should be dropped in the tender box provided in the HMT(I) office and ensure delivery on or
before 1400 hrs (IST) on the closing date. Late offers will not be considered.
Last date for submission of bids: 18.11.2014 up to 14.00 hrs
Technical bids will be opened on 18.11.2014 at 14.30 hrs in the Board room of HMT(I) office,
Bangalore.
End Of Section - I
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 5 of 115
SECTION II- INSTRUCTIONS TO BIDDERS (ITB)
1
2
3
4
4.1
Definitions and Interpretation
The “HMT(I)” / “BUYER” means: HMT(International) Limited, No.59, Bellary Road, Bangalore-560 032.
The “Supplier” means any firm/institute/company to whom the contract is awarded.
“SITE” means Rajiv Gandhi School of Production & Art, Ulaanbaatar, Mongolia, where the supplies are required to be
supplied, installed / erected and commissioned.
“PROJECT” means ‘Upgradation & Modernisation of Rajiv Gandhi School of Production and Art, Ulaanbaatar, Mongolia –
Phase – II’
Compliance of Requirements
The supplies offered should be in accordance with the stipulated requirements in the “Scope of Supply”. The bidder shall
indicate his compliance or non-compliance against each of the requirements.
Place of Delivery of supplies
All supplies are to be delivered to HMT(I)’s shipping agent at FOR Chennai as per the instructions given by HMT(I) at the
time of dispatch.
Criteria for pre qualification of Bidder
The Bidder shall satisfy the following prequalification criteria:
The Bidder shall provide satisfactory documentary evidence acceptable to HMT(I) to show that:
The Bidder’s average annual turnover to be at least as indicated below in the last three financial years. The Bidders
should furnish audited accounts for previous 3 years.
LOT -1: Rs.10.0 lakh (Rupees Ten lakh only)
LOT -2: Rs.90.00 lakh (Rupees Ninety lakh only)
LOT -3: Rs.5.00 crore (Rupees Five crore only)
LOT -4: Rs.20.00 lakh (Rupees Twenty lakh only)
LOT -5: Rs.10.00 lakh (Rupees Ten lakh only)
LOT -6: Rs.5.00 crore (Rupees Five crore only)
LOT -7: Rs.20.00 lakh (Rupees Twenty lakh only)
-
4.2
4.3
5
6
6.1
6.2
6.3
6.4
6.5
The Total Annual turnover to bid for all the Lots is Rs 1150.00 lakh only (Total Rupees One thousand One
hundred Fifty lakh only).
The Bidder must have minimum 3 years continuous experience in manufacturing / supply of items specified in the Scope
of Supply. Attach at least one Purchase Order copy of each year separately for three years.
Bidder should submit satisfactory certificate from at least 2 reputed clients to whom similar nature of supplies has been
rendered.
If the Bidder does not submit the above required information along with documentary evidence at the time of bidding;
the bid may be rejected.
Cost of bid documents
o The cost of bid document is Rs. 2,500.00 (Rupees Two Thousand Five hundred only).
o The cost shall be payable in the form of a crossed Bank draft in favour of HMT (International) Ltd, Payable at
Bangalore and kept along with the Technical bid documents in Envelope –I, if the bid documents are downloaded
from website.
o If the documents are purchased from HMT (International) Limited, copy of the receipt for payment of cost of bid
documents shall be kept along with the Technical bid documents in Envelope –I.
o In case, the Bidder quotes for more than one lot, the copy of the receipt for payment of cost of bid documents shall
be kept along with the Technical bid documents in Envelope –I for each lots separately.
o If the cost of bid document is not paid before opening of the Technical bid, the bids will be rejected straightaway/
summarily.
Earnest Money Deposit
Earnest Money Deposit for the amount as stipulated in the “Bid Invitation” shall accompany Technical bid documents of
tender. The Earnest Money Deposit shall be in the forma of a crossed Bank Draft in favour of HMT (International) Ltd,
Payable at Bangalore. In case, the Bidder quotes for more than one lot, the copy of the crossed Bank Draft shall be kept
along with the Technical Bid documents in Envelope –I for each lot separately.
The Earnest Money Deposit shall remain deposited with HMT(I) for a period of 90 (ninety) days from the date of opening
of tenders. If the validity of the offer is extended, the EMD shall remain with HMT(I).
No interest will be payable by HMT(I) for the Earnest Money Deposit.
The Earnest Money deposited is liable to be forfeited if the bidder withdraw or amends, impairs or derogates from the
tender in any respect within the validity period of his offer.
The Earnest Money Deposit of the successful bidder will be returned after the P.O. is released on successful Bidder and
duly accepted and submission of Performance Guarantee.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 6 of 115
SECTION II- INSTRUCTIONS TO BIDDERS (ITB)
6.6
6.7
6.8
7
7.1
7.2
8
8.1
8.2
9
9.1
9.2
9.3
9.4
9.5
10
10.1
11
11.1
11.2
11.3
11.4
12
12.1
If the successful Bidder fails to furnish a contract performance guarantee, then the earnest money shall be liable to be
forfeited.
The Earnest Money Deposit of all unsuccessful Bidders will be returned to the bidder by HMT(I) after finalization of
contract with the successful bidder.
If Earnest Money Deposit as stipulated in the “Bid Invitation” is not enclosed in the Technical documents in Envelope –I,
the bid will be rejected straight away / summarily
Period of validity of bids
Bids shall be valid for a minimum period of 90 days from the last date of submission.
HMT(I) may ask for the bidder’s consent to extend the period of validity. Such request and the response shall be made in
writing only. A bidder agreeing to the request for extension will not be permitted to modify his bid. Technical
clarifications, if any, shall be furnished by Bidder within one week’s time.
Deadlines for submission of bids
Bids must be received by HMT(I) before the due date and time at the address specified in the tender document. In the
event of the specified date for the submission of bids being declared as a holiday for HMT(I), the bid-closing deadline will
stand extended to the next working day up to the same time.
HMT(I) may extend this deadline for submission of bids by amending the bid documents and same will be suitably
notified in HMT(I) website: www.hmti.com
Any bid received by HMT(I) after the deadline for submission of bids, will not be accepted and returned unopened to the
bidder.
Opening of Commercial bids by HMT(I)
The Technical Bids will be evaluated to shortlist the eligible bidders.
Bidder whose Technical Bid is found to be acceptable and meeting the eligibility requirements as specified in “Clause 4”
will be informed about the date and time of the opening of the Commercial Bid.
HMT(I) will open Commercial Bids of only the technically accepted and short listed bids, in the presence of the bidder or
their authorized representative who choose to attend the bid opening, at the time and date to be informed later.
The bidder’s authorized representative who attends the bid opening shall sign an attendance register as a proof for
having attended the bid opening.
The bidder’s name, bid prices, discounts and such other details considered as appropriate by HMT(I), will be announced
at the time of opening of the Commercial Bids.
Comparison of Bids
Bids received against the tender will be evaluated by the Technical Evaluation Committee (TEC) to ascertain the technical
suitability and will be shortlisted.
Short listed Technical bids only will be considered for Commercial Bid opening and commercial evaluation.
Award Criteria
HMT(I) will award the contract to the eligible bidder whose technical bid has been accepted and determined as the
lowest evaluated Commercial Bid on Lot-wise basis.
Should the amount put in words differ from the amount put in figures, or if there is an arithmetical error, the lesser
amount will be taken unless the difference is attributable to an obvious error, whereupon the correct amount will be
taken.
If more than one bidder quotes same lowest price, HMT(I) reserves the right to award the contract at its own discretion.
HMT(I) reserves the right to increase or decrease the quantum of supplies offered by the successful bidder at the rates &
other terms and conditions offered by them. The Bidder is bound to accept the increase or decrease in the quantum of
supplies during awarding of the contract.
HMT(I)’s Right to amend Scope of Supplies
HMT(I) reserves the right to accept or reject any or all bids without assigning any reason whatsoever.
12.2
HMT(I) reserves the right to increase or decrease the scope of supplies indicated in the bid documents after the award of
the tender and payment shall be made on pro-rata basis.
12.3
HMT(I) reserves the right to cancel/short close/extend the order at any given point of time due to Force Majeure or
directions from the Governments of India or Mongolia.
12.4
HMT(I) reserves the right to cancel / short close the order due to non-satisfactory performance by any of the service /
supply offered. Cost / damages arising out of such cancellation / short closure shall have to be borne by the bidder
12.5
Buyer shall recall any of the experts deputed to the project site on non-compliance to the rule of the land or guidelines
laid down by Govt. of India / Govt. of Mongolia / HMT(I) or any act that does not correspond to ethical behavior. Cost /
damages arising in such an event shall be borne by the bidder and shall forthwith send suitable replacement.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 7 of 115
SECTION II- INSTRUCTIONS TO BIDDERS (ITB)
13
13.1
13.2
13.3
14
15
15.1
15.2
15.3
15.4
15.5
15.6
15.7
Corrupt or Fraudulent Practices.
HMT(I) requires that the bidders who wish to bid for this project have highest standards of ethics.
HMT(I) will reject a bid if it determines that the Bidder recommended for award has engaged in corrupt or fraudulent
practices while competing for this contract;
HMT(I) may declare a vendor ineligible, either indefinitely or for a short period, if HMT(I) is aware that the vendor has
engaged in corrupt and fraudulent practice during the execution of the contract.
Interpretation of the clauses in the Tender Document / Contract Document
In case of any ambiguity/ dispute in the interpretation of any of the clauses in this Tender Document, HMT(I)'s
interpretation of the clauses shall be final and binding on all parties.
General
All offers shall be either Computer prints or hand written neatly in indelible ink. Tenders shall be free from CORRECTION
AND ERASURES, and Corrections if any, must be attested. Each page of the offer must be numbered consecutively, should
bear the tender number and should be signed by the Bidder at the bottom. A reference to the total number of pages
comprising offer must be made at the top right hand corner of the first page.
The Bidders must ensure that the conditions laid down for submission of offers detailed in the preceding paras, are
completely and correctly fulfilled.
The submission of any offer connected with these supplies and documents shall constitute an agreement that the Bidder
shall have no cause of action or claim, against HMT(I) for rejecting the offer. HMT(I) shall always be at liberty to reject or
accept any offer or offers at its sole discretion
Offers shall be deemed to be under consideration immediately after they are opened and until such time the official
intimation of award of contract is made by HMT(I) to the Bidder. While the offers are under consideration, Bidders and or
their representatives or other interested parties are advised to refrain from contacting HMT(I) by any means. If
necessary, HMT(I) will obtain clarifications on the offers by requesting for such information from any or all the Bidders,
only in writing. Bidders will not be permitted to change the contents of their offers after the offers have been opened.
Any individual(s) signing the tender and related documents should be a competent, authorised person or original copy of
power of authorization issued by the competent authority should accompany the tender.
Offers shall be as per the Instructions to Bidders and Terms & Conditions of contract given in bid documents. However
the Bidder shall indicate his acceptance or otherwise against each of clause and sub clauses of the Instruction to Bidders
and Terms & Condition of contract. For this purpose, the Bidder shall enclose a separate statement as per format
Section-V(2) indicating only the deviations from any clause or sub clause of the Instructions to Bidders and Terms &
Conditions of contract which Bidder proposes with justification for each deviation. The HMT(I), however reserves the
right to accept or reject these deviations and decision there on shall be final and binding.
Bids shall be complete in all respects accompanied by detailed literature, brochures with all necessary details in ENGLISH
or otherwise, the bids will not be considered.
End of Section - II
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 8 of 115
SECTION III: SPECIAL CONDITIONS OF CONTRACT (SCC)
1
2
3
4
5
Execution: Metric System
Colour : As specified in the Technical Specifications.
Electricals: Main supply: 380 V, 3 Ph, 50Hz AC 4 wired / 220 V, 1 Ph, 50Hz AC Supply
Delivery period for supplies: FOR Chennai within 8 weeks from the date of purchase order.
Delivery is the essence of the Contract. If there is delay penalty as per clause 14 is applicable.
Inspection, Re inspection and Acceptance:
The items shall be manufactured as per International Standards. The standards followed should be accepted by HMT(I). For this
purpose, the supplier shall furnish HMT(I) the standards being followed immediately for acceptance. The supplies will be
inspected by HMT(I) as decided by HMT(I). If any of the item is found defective, HMT(I) reserves right to procure the substitute
for the defective items from elsewhere at the risk and cost of the supplier and recover from the supplier the extra expenditure,
if any incurred by HMT(I). Consignment shall be dispatched only after getting clearance from HMT(I).
At least 2 weeks prior intimation regarding readiness of supplies, in all respects must be furnished to HMT(I) for inspection by
HMT(I) Quality Assurance Department or by its authorized representative. Complete equipment, standard/special accessories
attachments, tooling, etc including packing cases must be offered for inspection. HMT(I) reserves right to inspect the items by
HMT(I) and customer representative at supplier’s works.
6
7
8
9
10
11
12
13
14
15
16
17
The supplies will be inspected by HMTI by deputing HMTI’s quality assurance personnel to the vendor’s worksite. Inspection
and other deputation charges for the deputation of HMTI personnel shall have to be borne by the vendor. Vendors are required
to reimburse the Cost of Inspection at 6%of the total order value + Service Tax as applicable.
Packing:
All Supplies shall be packed in seaworthy wooden cases suitable for shipment by 20ft / 40 ft containers of size (LXBXH):
5900mmx2300mmx2300mm / 12000mmx2300x2300mm respectively.
Packing cases must have case-wise detailed packing list to be put inside the cases. Also, 3 copies of casewise packing list to be
sent to HMT(I) immediately after packing. All Necessary tools, fixtures, instruments, trail materials, consumables etc., for
installation to be sent along with the items. Packing to be made in the presence of HMT(I) inspection engineers.
Port of Shipment/ Discharge: Chennai Port / Port Ulaanbaatar, Mongolia.
Freight & Insurance:
Supplier to dispatch the goods on Freight Prepaid – Door Delivery basis to HMT(I) shipping agent at Chennai port of shipment.
Transit insurance to be arranged by supplier. Supplier to inform HMT(I), despatch details like Lorry receipt No., No. of Packing
cases, Gross Weight, Net Weight etc., immediately after dispatch from works.
Consignee: Consignee will be intimated later
Invoice to : HMT (International) Limited, 59, Bellary Road, Bangalore – 560 032, India TIN NO. 29760097661
A/c. RGSPA, Mongolia
Price: The price shall be FOR Chennai Port and considered firm and no escalation will be permitted.
Payment Terms for supplies:
100% payment for supplies will be payable on 60th day from the date of delivery to our shipping agent at Chennai. If the
Payment terms are not acceptable, the vendors can quote their own payment terms. 18% per annum interest will be loaded to
the quoted price for arriving at the total price for price evaluation only as per tender terms. However, the acceptance of the
payment terms indicated is at the sole discretion of HMT(I) Management.
All bank charges such as L/c opening charges, negotiation charges, etc., are to the account of supplier, if supplier requires
payment by inland L/C.
Payment for services portion: The payment will be made after getting certificate confirming successful Installation and
customer Training at site.
Penalty for delayed Supply and Services:
HMT(I) reserves the right to levy penalty @ 1.0 percent of order value per week of delay beyond the scheduled deliveries /
execution of the contract successfully, subject to maximum of 10% of the contract value. HMT(I) reserves the right to cancel the
contract in case the delay is more than 10 weeks. The penalties, if any shall be recovered by invoking the Performance Bank
Guarantee or withholding the amount out of the payments due.
Clearance for Despatch:
Equipment shall be dispatched only after getting clearance from HMT(I). Such clearance shall be furnished only after receipt of
a certificate from Supplier stating that the snags, if any, pointed out by HMT(I) Engineer/Customer’s representative have been
duly attended to. HMT(I) shall have the right to hold up the dispatch for want of any clearance from the customer. The
consignment shall be shipped through a reputed Transporters in a direct truck to reach HMT(I)’s shipping agent with out any
transshipment.
Name & Address of the Shipping Agent : Will be informed at the time of dispatch clearance by HMT(I).
Technical Documents:
Supplier to forward the detailed drawings of the all machines / equipment in 3 sets, indicating details about civil work required,
Electrical, Pneumatic, Water connection points etc., immediately on receipt of Purchase Order.
Instruction / Operating Systems / Spare Parts Manual and other relevant documents pertaining to the Equipment must be in
English and should be supplied in (3) three sets as follows :
o 2 Sets of Manuals along with the machine / equipment
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 9 of 115
SECTION III: SPECIAL CONDITIONS OF CONTRACT (SCC)
18
19
20
21
22
23
24
25
o 1 set Manual to HMT(I), Bangalore
o Two copies of Electrical wiring drawings (along with the machine / equipment)
o Instructions for commissioning (One copy along with the machine / equipment) and one copy to HMT(I)
o Final Test & Inspection Report (along with the machine / equipment)
Bought Outs:
All the bought-out items such as bearings, belts, electricals, motors, contactors, switches etc., shall correspond to ISI /
International Specifications and shall be of reputed make like, SKF, FENNER, SIEMENS & TELEMECHANIC etc.,
Rejection & Risk:
If, HMT(I) finds that the materials supplied are not of correct quality or not according to the specifications as indicated in the
bid offer, then HMT(I) will be entitled to reject the offer
Performance Bank Guarantee (PBG):
The successful bidder will be required to furnish Performance Bank Guarantee for 10% amount of the Contract value, as per the
format attached to this document (Refer Section – V; Annexure – 4). This bank guarantee shall remain valid until the expiry of
warranty period or for the period of 12 months beyond the completion of Erection & Commissioning. If the Bidder is not
acceptable to furnish Performance Guarantee 10% of the contract value will be retained as “Retention Money” till expiry of
warranty period or for the period of 12 months beyond the completion of Erection & Commissioning. .
International Warranty:
The supplies shall be guaranteed against defects of material and workmanship for a period of 12 months from the date of
commissioning, Until the expiry of the warranty period, the supplier is obliged to do repairs, modifications, setting right and
adjustments considered necessary to guarantee the rated output and to replace any part of the machine / equipment found
defective and necessitate replacement due to design, manufacture, and material defect during the warranty period at project
site in Mongolia.
The supplier will arrange for free supply and replace/repair at his cost at site any part that may be found defective and
necessitates replacement due to design, manufacture and material defect during warranty period.
HMT(I) shall provide airfare, local hospitality to experts deputed during the warranty period as per the mutually agreed terms.
Installation:
o The supplier shall depute, the required technical personnel for carrying out installation and providing training to the
customers personnel in operation & maintenance of items at project site in Mongolia.
o HMT(I) shall arrange to provide, free furnished bachelor’s accommodation, local transport and necessary assistance in
getting VISA for the Technical Personnel deputed to site in Mongolia. To & Fro Airfare, Boarding expenses, Travel Insurance
and incidental expenses to be borne by the supplier.
o The supplier shall depute their personnel within 15 days from the date of intimation of readiness at project site in
Mongolia.
o In case the technical personnel extended their period of stay beyond the stipulated/required/agreed time, the additional
cost for their extended stay has to be borne by the supplier.
Arbitration:
All disputes of any kind arising out of supply, acceptance, warranty maintenance etc., shall be referred after issuance of 30 days
notice in writing clearly mentioning the nature of dispute to a single arbitrator to be appointed by HMT(I). The venue for
arbitration shall be Bangalore.
Jurisdiction:
The disputes, legal matters, court matters, if any shall be subject to Bangalore jurisdiction only.
Force Majeure:
HMT(I) may consider relaxing the penalty and delivery requirements, as specified in this document, if and to the extent that,
the delay in performance or other failure to perform its obligations under the Contract is the result of a Force Majeure. Force
Majeure is defined as an event of effect that cannot reasonably be anticipated such as acts of God (like earthquakes, floods,
storms etc.), acts of states, the direct and indirect consequences of wars (declared or undeclared), hostilities, national
emergencies, civil commotion and strikes at successful Bidder’s premises.
Either party shall be excused from performance of their obligation during or to the extent that performance is prevented by the
occurrence of unforeseen causes beyond the control of and without the negligence of the party claiming excuse. Such causes
shall include, without limitation, strike, go slow , other concerted acts of workmen, lockout, Act of God, war, fire, explosion,
action of elements, flood, epidemic, riot, sabotage, embargo, blockade, civil disturbance and Governmental restrictions or
limitations etc.
The party claiming excuse shall give immediate written notice thereof to the other, in any case not later that 15 (fifteen) days,
following the occurrence of such event. If performance is held for a continuous period of more than 3 (three) months from the
date of first notice, then the parties shall review the situation and agree upon any course of action so as to protect the interest
of both.
End of Section - III
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 10 of 115
SECTION – IV: SCHEDULE OF REQUIREMENTS / SCOPE OF SUPPLIES (SR)
Schedule of Requirements / Scope of Supplies is as detailed below
LOT – 1 Machine Tools - Pillar & Pedestal Drilling Machines
Project: Upgradation & Modernisation of Rajiv Gandhi School of Production and Art, Ulaanbaatar, Mongolia –
Phase – II
Sl.
Annex.
Qty
Remarks /
Description
Brief Specification
No.
Ref.
In Nos.
Deviations
1
4/45
Pillar Type Drilling Machine
Drilling Cap.: 20mm/MT2, Tapping
2
Cap. : M12, Feed: Hand
2
6/13
Pillar Type Drilling Machine
Drilling Cap.: 13mm/MT1, Feed:
1
Hand
3
6/09
Pedestal Grinding Machine
Centre distance between wheels
1
(approx.): 420 mm, Height from
base to Spindle Centre (approx):
910 mm, Wheel Size: 200mm
FOR DETAILED TECHNICAL SPECIFICATIONS REFER ENCLOSURE - I
LOT - 2 Welding Equipment
Project: Upgradation & Modernisation of Rajiv Gandhi School of Production and Art, Ulaanbaatar, Mongolia –
Phase – II
Sl.
Annex.
Qty
Remarks /
Description
Brief Specification
No.
Ref.
In Nos.
Deviations
1
6/17
Welding Transformer
40 – 300A
4
2
6/18
Welding Transformer
40 – 400A
4
3
6/19
Welding Rectifier
1
4
6/20
Spot Welding Machine
1
5
6/21
Mig Welding Equipment
60 – 400A
2
6
6/22
Tig Welding Equipment
40 – 400A
2
7
6/23
Submerged Arc Welding
1000A
2
8
6/24
Oxy - Acetylene Gas Welding
4
Equipment
9
6/25
Portable Flame Cutting
1
Machine
FOR DETAILED TECHNICAL SPECIFICATIONS REFER ENCLOSURE - II
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 11 of 115
LOT - 3 Electrical Machine Trainers
Project: Upgradation & Modernisation of Rajiv Gandhi School of Production and Art, Ulaanbaatar, Mongolia –
Phase – II
Sl.
Annex.
Qty
Remarks /
Description
Brief Specification
No.
Ref.
In Nos. Deviations
1
Electrical Machine Trainer
1
4/1
1.1
Work Table for Electrical Machine Trainer
1
4/2
2.
Industrial Control Trainer
1
2.2
Worktable for Industrial Control Trainer
1
4/3
3.
3 Phase AC Motor Fault Simulator
1
3.1
Work Table for 3 Phase AC Motor Fault
1
Simulator
4/4
4
House Wiring Installation Trainer
1
4.1
Work Table for House Wiring Installation
1
Trainer
4/5
5
Electrical Control Trainer
1
5.1
Work Table for Electrical Control Trainer
1
4/6
6
Power Electronics Trainer
1
6.1
Work Table for Power Electronics Trainer
1
4/7
7
Applied Power Electronics Trainer
1 Set
7.1
Work Table for Applied Power Electronics
1
Trainer
4/8
8
Electrical Trainer
1
8.1
Work Table for Electrical Trainer
1
9
3-Phase Induction Motor Speed Control
1
4/9
Trainer
9.1
Work Table for 3-Phase Induction Motor
1
Speed Control Trainer
10
3-Phase Induction Motor Fault Simulator
1
4/10
10.1
Work Table for 3-Phase Induction Motor
1
Fault Simulator
4/11
11
Motor Generator (AC to DC) set
1
11.1
Work Table for Motor Generator (AC to DC)
1
set
12
Motor Generator
1
4/12
(DC to AC) set
12.1
Work Table for Motor Generator
1
(DC to AC) set
4/13
13
DC Generators
1
13.1
Work Table for DC Generators
1
14
Motor Series DC , Motor Shunt DC &Motor
1
4/15,
4/16 & Compound Wound DC
4/17
14.1
Work Table for Motor Series DC , Motor
1
Shunt DC &Motor Compound Wound DC
4/18
15
Motor Squirrel-cage AC
1
15.1
Work Table for Motor Squirrel-cage AC
1
16
Motor wound slip ring AC
1
4/19
16.1
Work Table for Motor wound slip ring AC
1
17
4/20 & Motor Series AC &Motor Capacitor AC
1
4/21
17.1
Work Table for Motor Series AC & Motor
1
Capacitor AC
18
4/22
Motor Universal AC
1
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 12 of 115
Project: Upgradation & Modernisation of Rajiv Gandhi School of Production and Art, Ulaanbaatar, Mongolia –
Phase – II
Sl.
Annex.
Qty
Remarks /
Description
Brief Specification
No.
Ref.
In Nos. Deviations
18.1
Work Table for Motor Universal AC
1
4/23
19
Stepper motor
1
19.1
Work Table for Stepper motor
1
4/42
20
Thyristor / IGBT controlled DC trainer
1 HP Motor
1
20.1
Work Table for Thyristor / IGBT controlled
1
DC trainer
4/43
21
Thyristor / IGBT controlled AC trainer
Motor Drive 2HP with
1
VVVF control.
21.1
Work Table for Thyristor / IGBT controlled
1
AC trainer
22
4/155 Electrical Table for experiments / Test Electrical
3
&
Bench
4 /156
FOR DETAILED TECHNICAL SPECIFICATIONS REFER ENCLOSURE – III
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 13 of 115
LOT - 4 Electrical Appliances
Project: Upgradation & Modernisation of Rajiv Gandhi School of Production and Art, Ulaanbaatar, Mongolia
– Phase – II
Remarks
Sl. Annex
ITEM
Brief Specification
Qty /
No
Ref.
Deviation
1.
4/24 Fan
Ceiling Fan of AC 230 V, 1200 mm blades
2
2. 4/115 Electric Hot plate
1500W, 220V with temp control
3
3. 4/116 Electrical Kettle
1000 Watts
3
4. 4/117 Electric Iron box
1200Watts, 230V,
3
5. 4/118 Immersion heater
1000W, 230V
3
6. 4/119 Geyser
Geyser of minimum 25 litres capacity – 230 V
2
(Storage type)
7. 4/120 Induction stove
minimum 120 W to 2000W
2
8. 4/121 Microwave Oven
Micro Oven of minimum 30 Litres capacity
2
convection type.
9. 4/122 Electric Cooker
Automatic Electric Rice Cooker 1.8 Litre
2
Capacity (
10. 4/148 Sodium vapor Lamp
240v, 80W
2
fitting
11. 4/149 Florescent lamp fitting
230 V, 4 FT, Electronic choke 40W
7
&
Tube Light
4/160
12. 4/150 Mercury vapor lamp
240 V, 80 W
2
fitting
13. 4/158 Domestic water pump
Capacity of 1 HP
3
with starter
14. 4/159 Electric Toaster
2
15. 4/162 Semi Automatic Washing minimum 3.5 Kg Capacity
2
machine
16. 4/163 Automatic Washing
minimum 3.5 Kg Capacity
2
machine
17. 4/164 Wall Fan
Wall fan of 18" sweep blade size
3
18.
3/1
P.A Amplifier
Power output: 160W
2
19.
3/8
T.V. colour set
I. LED Smart TV with the following specification.
1
a) Screen size: 42 inches (107 cms) LED
Display
II. LED TV with the following specification.
1
a) Screen size: 40 inches LED Display
20. 3/21 Inter com System
2
21. 3/25 Push button telephone
2
set
22. 3/28 T.V. Camera Color
Full set of Handy cam corder with & Other
2
accessories with 240GB hard disk
23. 3/29 Cord less
Digital Cordless Telephone , 2.4GHz Frequency
2
Telephone set
24. 3/83 Loud Speakers
2 Way Loudspeakers with woofer
2
25. 3/84 Microphone
Wireless Microphone with wireless receiver for
8
enhanced mobility
26. 3/85 Headphone- earphone
8
Sets
FOR DETAILED TECHNICAL SPECIFICATIONS REFER ENCLOSURE - IV
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 14 of 115
LOT - 5 ELECTRICAL & ELECTRONIC EQUIPMENT:
Project: Upgradation & Modernisation of Rajiv Gandhi School of Production and Art, Ulaanbaatar, Mongolia
– Phase – II
Remarks
Sl. Annex
ITEM
Brief Specification
Qty /
No Ref.
Deviation
1
3/4
Sweep generator with
3
X-Y display with marker
2
3/11 Signal Injector
8
3
3/18 Logic Probes
Display: LED
8
4
3/44 Power Supply Unit
Output voltage: Fixed ± 5 V, ± 12 V DC
10
5
3/50 Cell phone PCB holder - To hold the PCB’s of cell phone of different types
1
Lot
& minimum 4 types
Lot
6
3/64 Solenoid with core
Solenoid valve with core
4
7
3/65 Electric bells set of
One Set consisting of Eight Nos of different types
8
different types
of Electric bells of both AC & DC
sets
8
3/66 Battery Eliminator
The output voltages is selectable from 0-2V DC,
8
4V DC, 6V DC, 8V DC, 10V DC, 12V DC at 3A.
Display of voltages & Currents through voltmeter
and ammeter.
9
3/86 Receiver aco real kit
3
10 3/87 Service Oscillator
3
11 3/88 Signal Tracer
3
12 4/40 Battery Charger
With variable output of 1KW
2
13 4/102 Wheat stone bridge
Range : 0 – 10 KOhm
2
14 4/108 Load bank
Load range: 0 - 5 KW in different steps
2
15 4/111 DC power supply
Output: 0-100V, 5A.
3
16 4/113 Servo Voltage Stabilizer Rating: 1 KVA.
2
1
17 4/145 Motor Winding Set
• Armature winding of FHP AC motor set for
motor winding practice.
1
• Armature winding of FHP DC motor set
for motor winding practice.
18 4/146 Auto transformer
three phase
1
19 4/161 Earth Resistance Tester Earth Resistance: 0-2000 Ω
2
FOR DETAILED TECHNICAL SPECIFICATIONS REFER ENCLOSURE - V
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 15 of 115
LOT - 6 Electronic Trainers
Project: Upgradation & Modernisation of Rajiv Gandhi School of Production and Art, Ulaanbaatar, Mongolia –
Phase – II
Sl. Annex
Remarks /
ITEM
Brief Specification
Qty
No Ref.
Deviation
1
4/26 Oscilloscope - Digital
30 MHz Digital Storage Oscilloscope
10
&
3/2
2
3/5
Bread Board trainer with
2
kits
Sets
3
3/22 C.R.O. Trainer kit
Bandwidth: 25-30 MHz
4
&
3/23
4
3/3
Power Supply set
Power Supply Set 0-30V & 0-300V DC
8
5
3/6
AC Bridge rectifier Trainer
1
6
3/7
TV Trainer kit
LCD/LED Television Trainer
4
7
3/9
Pattern generator
Colour Pattern Generator:
3
8
3/10
Signal generator Am/Fm
Frequency Range: 1 Hz - 10 MHz
3
9
3/12
Distortion meter
Frequency: 20 Hz to 20 KHz
1
10
3/13
Strain gauge with load cell
Approximately 400 gm
2
11
12
3/15
3/16
DVD Trainer kit
Micro Processor Training kit
System: PAL, NTSC
1
3
13
3/17
&
4/32
Linear Digital I.C Trainer
5
14
3/19
Frequency Counter
15
3/20
A.F/R.F Oscillator
Digital Circuits to be covered: Minimum Basic logic gates, Universal gates, Flip-flops,
Counters, Multiplexers / Demultiplexers,
Encoder / Decoder, Full/Half Adder &
Substractor.
Frequency range: 10 Hz to 1 GHz with
minimum 2 steps, variable control between
steps
Radio Frequency Range: 10 MHz to 150 Mhz
Audio frequency Range: 10 Hz to 20 KHz
16
Function Generator Trainer
Kit
3
17
3/24
&
4/29
3/30
2
18
3/32
Cellular telephone set
trainer
SMPS Trainer
19
3/35
2
20
3/36
21
3/37
22
3/41
Electrical & Electronics
system Trainer
Communication system
trainer
EPABX Trainer kit
(Electronic Exchange)
EPROM Kit
3
3
2
2
2
Program Memory: Minimum 64 Kb
Display: LCD /LED
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 16 of 115
1
Project: Upgradation & Modernisation of Rajiv Gandhi School of Production and Art, Ulaanbaatar, Mongolia –
Phase – II
Sl. Annex
Remarks /
ITEM
Brief Specification
Qty
No Ref.
Deviation
23 3/42 A to D Trainer kit
1
24 3/43 D to A Trainer kit
1
25 3/71 Transistor Tester
2
26 3/72 I.C. Tester
2
27 3/89
A.F. Oscillator
Audio frequency: 1 Hz to 1 MHz
3
28 3/90 Frequency Modulator
Frequency range: 1Hz to 100 KHz
2
29 4/25 Industrial PLC trainer kit
1
30 4/30 Discrete Component trainer
2
&
3/14
31 4/31 Linear I.C. Trainer
1
32 4/44 Experimental Power
Power Devices :, Triac, UJT & SCR
1
Electronics Trainer
33 4/112 Inverter, sine wave
Power: 1KVA
2
FOR DETAILED TECHNICAL SPECIFICATIONS REFER ENCLOSURE - VI
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 17 of 115
LOT - 7 Electrical Meters
Project: Upgradation & Modernisation of Rajiv Gandhi School of Production and Art, Ulaanbaatar, Mongolia
– Phase – II
Sl.
Annex
Remarks /
ITEM
Brief Specification
Make
Qty
No
Ref.
Deviation
1
4/85 & Digital Multi
ISI STANDARD
18
3/48
meter
2
3/53
Digital Ohm
Upto 10 M.ohm range
ISI STANDARD
2
meter
3
4/114 Rheostats - set
MEC/
4 sets
&
TOSHNIWAL/
3/68
ISI STANDARD
4
3/73
DC/AC Ammeter Ammeter DC Digital portable AE / MECO /
3
type, 0-5 A range.
ELC /
Ammeter AC Digital portable UNITECH/
3
INDOTECH/
type, 0-5 A range.
ISI STANDARD
5
3/74
DC/AC Ammeter Ammeter DC Digital portable AE / MECO /
3
ELC /
type, 0-500 mA range.
Ammeter AC Digital portable UNITECH/
3
INDOTECH/
type, 0-500 mA range.
ISI STANDARD
6
3/75
DC/AC Ammeter Ammeter DC Digital portable AE / MECO /
3
type, 0-1 mA range.
ELC /
Ammeter AC Digital portable UNITECH/
3
INDOTECH/
type, 0-1 mA range.
ISI STANDARD
7
3/76
DC/AC Ammeter Ammeter DC Digital portable AE / MECO /
3
type, 0-5 mA range.
ELC /
Ammeter AC Digital portable UNITECH/
3
INDOTECH/
type, 0-5 mA range.
ISI STANDARD
8
3/77
DC/AC Ammeter Ammeter DC Digital portable AE / MECO /
3
ELC /
type, 0-100 mA range.
Ammeter AC Digital portable UNITECH/
3
INDOTECH/
type, 0-100 mA range.
ISI STANDARD
9
3/78
DC/AC
Voltmeter DC/AC, Digital AE / MECO /
3
Voltmeter
portable type, 0-5 V range
ELC /
UNITECH/
INDOTECH/
ISI STANDARD
10
3/79
DC/AC
Voltmeter DC/AC, Digital AE / MECO /
3
Voltmeter
portable type 0-10 V range
ELC /
UNITECH/
INDOTECH/
ISI STANDARD
11
3/80
DC/AC
Voltmeter DC/AC, Digital AE / MECO /
3
Voltmeter
portable type 0-50 V range
ELC /
UNITECH/
INDOTECH/
ISI STANDARD
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 18 of 115
Project: Upgradation & Modernisation of Rajiv Gandhi School of Production and Art, Ulaanbaatar, Mongolia
– Phase – II
Sl.
Annex
Remarks /
ITEM
Brief Specification
Make
Qty
No
Ref.
Deviation
12
3/81
DC/AC
Voltmeter DC/AC, Digital AE / MECO /
3
Voltmeter
portable type 0-500 V range
ELC /
UNITECH/
INDOTECH/
ISI STANDARD
13
4/41
M.C.B
MDS /
2 sets
SIEMENS /
GLOSTAR/
ISI STANDARD
14
4/84
Analog multi
AE / MECO /
4
Meter
PROTECT /
METRAVI /
MASTECH/
ISI STANDARD
15
4/86
A.C. Voltmeter,
AE / MECO /
2
MI
ELC / NIPPEN
/ BRISTEL /
UNITECH
/INDOTECH/
ISI STANDARD
2
16
4/87
Milli Voltmeter
100 – 0 -100 millivolts,
AE / MECO /
centre zero
ELC / NIPPEN/
ISI STANDARD
2
17
4/88
D.C Milli
0 - 500 mA
AE / MECO /
ammeter
ELC / NIPPEN/
ISI STANDARD
18
4/89
D.C. Ammeter
0 – 1 A,MC,
AE / MECO /
2
MC
ELC / NIPPEN/
ISI STANDARD
19
4/90
Ammeter MC
Portable, MC, Range: 0-5 A
AE / MECCO /
2
UNITECH
/INDOTECH/
ISI STANDARD
20
4/91
Ammeter MC
Portable, MC, Range: 0-15-25 AE / MECCO /
2
A
UNITECH/
INDOTECH/
ISI STANDARD
21
4/92
A.C. Ammeter
Portable , MI, Range 0-5 A
MECO / EIC /
2
MI
NIPPEN /
BRISTEL/
ISI STANDARD
22
4/93
A.C. Ammeter
Portable, MI, Class-1, Multi
MECO / EIC /
2
MI
Range
NIPPEN /
0-15-25 A
BRISTEL/
ISI STANDARD
23
4/94
K.W. Meter
AE / MECO /
2
ECI / NIPPEN /
INDOTECH/
ISI STANDARD
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 19 of 115
Project: Upgradation & Modernisation of Rajiv Gandhi School of Production and Art, Ulaanbaatar, Mongolia
– Phase – II
Sl.
Annex
Remarks /
ITEM
Brief Specification
Make
Qty
No
Ref.
Deviation
24
4/95
A.C. Energy
TECHNO /
2
Meter
UNITECH
/INDO TECH/
ISI STANDARD
25
4/96
Single Phase
AE / MECCO/
2
power factor
EIC / NIPPEN /
meter
INDOTECH /
MEC/
ISI STANDARD
26
4/97
Frequency
ISI STANDARD
2
Meter
27
4/99
Growler
Inside & Outside Growler set
MASTECH/
2 set
MEC/
ISI STANDARD
28
4/100 Tong tester/
0 - 5 -10 Amps,
ISI STANDARD
2
Clamp meter
29
4/101 Megger set
Megger set of range 500 Volts WACO/MAST
2 sets
& 1000Volts
ECH/
ISI STANDARD
30
4/123 Flux meter
Digital flux meter
ISI STANDARD
2
31
4/124 Lux meter
Lux meter
KUSUM/MAS
2
TECH/
LUTRON/
ISI STANDARD
32
4/157 Clamp on
Digital Clamp meter
KUSAM –
3
Ammeter
MECO/
ISI STANDARD
FOR DETAILED TECHNICAL SPECIFICATIONS REFER ENCLOSURE - VII
End of Section – IV
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 20 of 115
SECTION V– COMMERCIAL
Annexure – 1
PRICE SCHEDULE
LOT – 1 Machine Tools
Project: Upgradation & Modernisation of Rajiv Gandhi School of Production and Art, Ulaanbaatar,
Phase – II
Unit FOR
Sl.
Annex
Chennai
ITEM
Brief Specification
Qty
No
Ref.
Port Price
in Ind. Rs
1
4/45
Pillar
Type
Drilling Drilling
Cap.:
20mm/MT2,
2
Machine
Tapping Cap. : M12, Feed: Hand
2
6/13
Pillar
Type
Drilling Drilling Cap.: 13mm/MT2, Feed:
1
Machine
Hand
3
6/09
Pedestal
Grinding Centre distance between wheels
1
Machine
(approx.): 420 mm, Height from
base to Spindle Centre (approx):
910 mm, Wheel Size: 200mm
Total FOR Chennai Port Prices in Indian Rupees
Total Indian Rupees (in words)
Mongolia –
Total FOR
Chennai
Port Price
in Ind. Rs.
It is hereby certified that we have understood the instruction to Bidders and also the Terms & Conditions of
Contract attached to the tender and have thoroughly examined and are aware of the nature of
supplies/services required and our offer is to render supplies/services strictly in accordance with the
requirements and according to the terms of the tender. We agree to abide solely by the terms & conditions of
contract and other conditions of the tender in accordance with the tender documents if the contract is
awarded to us.
We hereby offer to render supplies/ services as detailed above or such portion thereof as you may specify in
the acceptance of tender at the price quoted and agree to hold this offer open for acceptance for a period of
90 days from the date of opening of tender. We shall be bound by the communication of acceptance
dispatched within the prescribed time.
We possess the necessary License from the Government of India/State Government for rendering the supplies
/ services.
Dated:……………………………..
Signature and seal of Authorized Signatory
NOTE
1.
2.
3.
4.
5.
The offer must be submitted as per above proforma. The Bidder may use his letterhead to submit his offer.
No erasures or alternations in the text of the offer are permitted.
Any correction made in offer shall be initialed by the Bidder.
VALUES should be both in figures and Words.
The prices quoted should be most competitive
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 21 of 115
LOT - 2 Welding Equipment
Project: Upgradation & Modernisation of Rajiv Gandhi School of Production and Art, Ulaanbaatar, Mongolia –
Phase – II
Unit FOR
Total FOR
Sl.
Annex
Chennai Port
Chennai
ITEM
Brief Specification
Qty
Price in Ind.
Port Price
No
Ref.
Rs
in Ind. Rs.
1
6/17
Welding Transformer
40 – 300A
4
2
6/18
Welding Transformer
40 – 400A
4
3
6/19
Welding Rectifier
1
4
6/20
Spot Welding Machine
1
5
6/21
Mig Welding Equipment
60 – 400A
2
6
6/22
Tig Welding Equipment
40 – 400A
2
7
6/23
Submerged Arc Welding
1000A
2
8
6/24
Oxy - Acetylene Gas Welding
4
Equipment
9
6/25
Portable Flame Cutting Machine
1
Total FOR Chennai Port Prices in Indian Rupees
Cost towards Installation, Commissioning and training the customer’s personnel in operation and maintenance
for above Pre Printing Equipment at project site in Mongolia
*Total Indian Rupees (in words)
*Total should include the cost towards the following:
a. Deputation of technical personnel for carrying out installation, commissioning, trials, training the
customer’s personnel in operation and maintenance of above equipment at project site in Mongolia.
b. Necessary tools, fixtures, instruments, trial materials, consumables, etc, for Installation and training have
to be sent along with the supplies.
Please indicate the man day rates considered for deputation on the format given below
Sl No.
No. of Persons required for Installation,
Commissioning and Training of LOT 2 equipment
No. of Man days Cost per man day
required
(In Rs.)
It is hereby certified that we have understood the instruction to Bidders and also the Terms & Conditions of
Contract attached to the tender and have thoroughly examined and are aware of the nature of
supplies/services required and our offer is to render supplies/services strictly in accordance with the
requirements and according to the terms of the tender. We agree to abide solely by the terms & conditions of
contract and other conditions of the tender in accordance with the tender documents if the contract is
awarded to us.
We hereby offer to render supplies/ services as detailed above or such portion thereof as you may specify in
the acceptance of tender at the price quoted and agree to hold this offer open for acceptance for a period of
90 days from the date of opening of tender. We shall be bound by the communication of acceptance
dispatched within the prescribed time.
We possess the necessary License from the Government of India/State Government for rendering the supplies
/ services.
Dated:……………………………..
Signature and seal of Authorized Signatory
NOTE
1.
2.
3.
4.
5.
The offer must be submitted as per above proforma. The Bidder may use his letterhead to submit his offer.
No erasures or alternations in the text of the offer are permitted.
Any correction made in offer shall be initialed by the Bidder.
VALUES should be both in figures and Words.
The prices quoted should be most competitive
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 22 of 115
LOT - 3 Electrical Machine Trainers
Project: Upgradation & Modernisation of Rajiv Gandhi School of Production and Art, Ulaanbaatar,
Phase – II
Unit FOR
Chennai
Annex
Sl. No
ITEM
Brief Specification Qty
Port Price in
Ref.
Ind. Rs
1
Electrical Machine Trainer
1
4/1
1.1
Work Table for Electrical Machine
1
Trainer
4/2
2.
Industrial Control Trainer
1
2.2
Worktable for Industrial Control
1
Trainer
3.
3 Phase AC Motor Fault Simulator
1
4/3
3.1
Work Table for 3 Phase AC Motor Fault
1
Simulator
4/4
4
House Wiring Installation Trainer
1
4.1
Work Table for House Wiring
1
Installation Trainer
4/5
5
Electrical Control Trainer
1
5.1
Work Table for Electrical Control
1
Trainer
4/6
6
Power Electronics Trainer
1
6.1
Work Table for Power Electronics
1
Trainer
4/7
7
Applied Power Electronics Trainer
1 Set
7.1
Work Table for Applied Power
1
Electronics Trainer
4/8
8
Electrical Trainer
1
8.1
Work Table for Electrical Trainer
1
4/9
9
3-Phase Induction Motor Speed
1
Control Trainer
9.1
Work Table for 3-Phase Induction
1
Motor Speed Control Trainer
10
3-Phase Induction Motor Fault
1
4/10
Simulator
10.1
Work Table for 3-Phase Induction
1
Motor Fault Simulator
4/11
11
Motor Generator (AC to DC) set
1
11.1
Work Table for Motor Generator (AC to
1
DC) set
12
Motor Generator
1
4/12
(DC to AC) set
12.1
Work Table for Motor Generator
1
(DC to AC) set
4/13
13
DC Generators
1
13.1
Work Table for DC Generators
1
14
Motor Series DC , Motor Shunt DC
1
4/15,
4/16 & &Motor Compound Wound DC
4/17
14.1
1
Work Table for Motor Series DC ,
Motor Shunt DC &Motor Compound
Wound DC
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 23 of 115
Mongolia –
Total FOR
Chennai
Port Price
in Ind. Rs.
Project: Upgradation & Modernisation of Rajiv Gandhi School of Production and Art, Ulaanbaatar,
Phase – II
Unit FOR
Annex
Chennai
ITEM
Brief Specification Qty
Sl. No
Ref.
Port Price in
Ind. Rs
4/18
15
Motor Squirrel-cage AC
1
15.1
Work Table for Motor Squirrel-cage AC
1
4/19
16
Motor wound slip ring AC
1
16.1
Work Table for Motor wound slip ring
1
AC
4/20 & Motor Series AC &Motor Capacitor AC
17
1
4/21
17.1
Work Table for Motor Series AC &
1
Motor Capacitor AC
18
Motor Universal AC
1
4/22
18.1
Work Table for Motor Universal AC
1
19
Stepper motor
1
4/23
19.1
Work Table for Stepper motor
1
20
4/42
Thyristor / IGBT controlled DC trainer
1 HP Motor
1
20.1
1
Work Table for Thyristor / IGBT
controlled DC trainer
21
4/43
Thyristor / IGBT controlled AC trainer
Motor Drive 2HP
1
with
VVVF
control.
Work Table for Thyristor / IGBT
21.1
1
controlled AC trainer
22
4/155
Electrical Table for experiments / Test Electrical
3
&
Bench
4 /156
Total FOR Chennai Port Prices in Indian Rupees
Cost towards Installation, Commissioning and training the customer’s personnel in operation and
maintenance for above Pre Printing Equipment at project site in Mongolia.
*Total Indian Rupees (in words)
*Total should include the cost towards the following:
Mongolia –
Total FOR
Chennai
Port Price
in Ind. Rs.
a. Deputation of technical personnel for carrying out installation, commissioning, trials, training the
customer’s personnel in operation and maintenance of above equipment at project site in Mongolia.
b. Necessary tools, fixtures, instruments, trial materials, consumables, etc, for Installation and training have
to be sent along with the supplies.
Please indicate the man day rates considered for deputation on the format given below
Sl No.
No. of Persons required for Installation, No. of Man days Cost per man day
Commissioning & Training of LOT 3 equipment
required
(In Rs.)
It is hereby certified that we have understood the instruction to Bidders and also the Terms & Conditions of
Contract attached to the tender and have thoroughly examined and are aware of the nature of
supplies/services required and our offer is to render supplies/services strictly in accordance with the
requirements and according to the terms of the tender. We agree to abide solely by the terms & conditions of
contract and other conditions of the tender in accordance with the tender documents if the contract is
awarded to us.
We hereby offer to render supplies/ services as detailed above or such portion thereof as you may specify in
the acceptance of tender at the price quoted and agree to hold this offer open for acceptance for a period of
90 days from the date of opening of tender. We shall be bound by the communication of acceptance
dispatched within the prescribed time.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 24 of 115
We possess the necessary License from the Government of India/State Government for rendering the supplies
/ services.
Dated:……………………………..
Signature and seal of Authorized Signatory
NOTE
1.
2.
3.
4.
5.
The offer must be submitted as per above proforma. The Bidder may use his letterhead to submit his offer.
No erasures or alternations in the text of the offer are permitted.
Any correction made in offer shall be initialed by the Bidder.
VALUES should be both in figures and Words.
The prices quoted should be most competitive
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 25 of 115
LOT - 4 Electrical Appliances
Project: Upgradation & Modernisation of Rajiv Gandhi School of Production and Art, Ulaanbaatar,
Phase – II
Unit FOR
Sl.
Chennai
Annex Ref.
ITEM
Brief Specification
Qty
No
Port Price
in Ind. Rs
1.
4/24
Fan
Ceiling Fan of AC 230 V, 1200 mm
2
blades
2.
4/115
Electric Hot plate
1500W, 220V with temp control
3
3.
4/116
Electrical Kettle
1000 Watts
3
4.
4/117
Electric Iron box
1200Watts, 230V,
3
5.
4/118
Immersion heater
1000W, 230V
3
6.
4/119
Geyser
Geyser of minimum
25 litres
2
capacity – 230 V (Storage type)
7.
4/120
Induction stove
minimum 120 W to 2000W
2
8.
4/121
Microwave Oven
Micro Oven of minimum 30 Litres
2
capacity convection type.
9.
4/122
Electric Cooker
Automatic Electric Rice Cooker 1.8
2
Litre Capacity (
10.
4/148
Sodium vapor Lamp 240v, 80W
2
fitting
11.
4/149 &
Florescent lamp
230 V, 4 FT, Electronic choke 40W
7
4/160
fitting Tube Light
12.
4/150
Mercury vapor lamp 240 V, 80 W
2
fitting
13.
4/158
Domestic water
Capacity of 1 HP
3
pump with starter
14.
4/159
Electric Toaster
2
15.
4/162
Semi Automatic
minimum 3.5 Kg Capacity
2
Washing machine
16.
4/163
Automatic Washing minimum 3.5 Kg Capacity
2
machine
17.
4/164
Wall Fan
Wall fan of 18" sweep blade size
3
18.
3/1
P.A Amplifier
Power output: 160W
2
19.
3/8
T.V. colour set
I. LED Smart TV with the following
1
specification.
b) Screen size: 42 inches (107
cms) LED Display
II. LED TV with the following
1
specification.
b) Screen size: 40 inches LED
Display
20.
3/21
Inter com System
2
21.
3/25
Push button
2
telephone set
22.
3/28
T.V. Camera Color
Full set of Handy cam corder with &
2
Other accessories with 240GB hard
disk
23.
3/29
Cord less
Digital Cordless Telephone , 2.4GHz
2
Telephone set
Frequency
24.
3/83
Loud Speakers
2 Way Loudspeakers with woofer
2
25.
3/84
Microphone
Wireless Microphone with wireless
8
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 26 of 115
Mongolia –
Total FOR
Chennai
Port Price
in Ind. Rs.
Project: Upgradation & Modernisation of Rajiv Gandhi School of Production and Art, Ulaanbaatar,
Phase – II
Unit FOR
Sl.
Chennai
Annex Ref.
ITEM
Brief Specification
Qty
No
Port Price
in Ind. Rs
receiver for enhanced mobility
26.
3/85
Headphone8 Sets
earphone
Total FOR Chennai Port Prices in Indian Rupees
Total Indian Rupees (in words)
Mongolia –
Total FOR
Chennai
Port Price
in Ind. Rs.
It is hereby certified that we have understood the instruction to Bidders and also the Terms & Conditions of
Contract attached to the tender and have thoroughly examined and are aware of the nature of
supplies/services required and our offer is to render supplies/services strictly in accordance with the
requirements and according to the terms of the tender. We agree to abide solely by the terms & conditions of
contract and other conditions of the tender in accordance with the tender documents if the contract is
awarded to us.
We hereby offer to render supplies/ services as detailed above or such portion thereof as you may specify in
the acceptance of tender at the price quoted and agree to hold this offer open for acceptance for a period of
90 days from the date of opening of tender. We shall be bound by the communication of acceptance
dispatched within the prescribed time.
We possess the necessary License from the Government of India/State Government for rendering the supplies
/ services.
Dated:……………………………..
Signature and seal of Authorized Signatory
NOTE
1.
2.
3.
4.
5.
The offer must be submitted as per above proforma. The Bidder may use his letterhead to submit his offer.
No erasures or alternations in the text of the offer are permitted.
Any correction made in offer shall be initialed by the Bidder.
VALUES should be both in figures and Words.
The prices quoted should be most competitive
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 27 of 115
LOT - 5 ELECTRICAL & ELECTRONIC EQUIPMENT:
Project: Upgradation & Modernisation of Rajiv Gandhi School of Production and Art, Ulaanbaatar,
Phase – II
Unit FOR
Sl.
Chennai
Annex Ref.
ITEM
Brief Specification
Qty
No
Port Price
in Ind. Rs
1
3/4
Sweep generator with X-Y
3
display with marker
2
3/11
Signal Injector
8
3
3/18
Logic Probes
Display: LED
8
4
3/44
Power Supply Unit
Output voltage: Fixed ± 5 V,
10
± 12 V DC
5
3/50
Cell phone PCB holder To hold the PCB’s of cell
1 Lot
Lot
phone of different types &
minimum 4 types
6
3/64
Solenoid with core
Solenoid valve with core
4
7
3/65
Electric bells set of
One Set consisting of Eight
8
different types
Nos of different types of
sets
Electric bells of both AC &
DC
8
3/66
Battery Eliminator
The output voltages is
8
selectable from 0-2V DC, 4V
DC, 6V DC, 8V DC, 10V DC,
12V DC at 3A. Display of
voltages & Currents through
voltmeter and ammeter.
9
3/86
Receiver aco real kit
3
10
3/87
Service Oscillator
3
11
3/88
Signal Tracer
3
12
4/40
Battery Charger
With variable output of 1KW
2
13
4/102
Wheat stone bridge
Range : 0 – 10 KOhm
2
14
4/108
Load bank
Load range: 0 - 5 KW in
2
different steps
15
4/111
DC power supply
Output: 0-100V, 5A.
3
16
4/113
Servo Voltage Stabilizer
Rating: 1 KVA.
2
17
4/145
Motor Winding Set
1
• Armature winding of
FHP AC motor set
for motor winding
practice.
1
• Armature winding of
FHP DC motor set
for motor winding
practice.
18
4/146
Auto transformer
three phase
1
19
4/161
Earth Resistance Tester
Earth Resistance: 0-2000 Ω
2
Total FOR Chennai Port Prices in Indian Rupees
Total Indian Rupees (in words)
Mongolia –
Total FOR
Chennai
Port Price
in Ind. Rs.
It is hereby certified that we have understood the instruction to Bidders and also the Terms & Conditions of
Contract attached to the tender and have thoroughly examined and are aware of the nature of
supplies/services required and our offer is to render supplies/services strictly in accordance with the
requirements and according to the terms of the tender. We agree to abide solely by the terms & conditions of
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 28 of 115
contract and other conditions of the tender in accordance with the tender documents if the contract is
awarded to us.
We hereby offer to render supplies/ services as detailed above or such portion thereof as you may specify in
the acceptance of tender at the price quoted and agree to hold this offer open for acceptance for a period of
90 days from the date of opening of tender. We shall be bound by the communication of acceptance
dispatched within the prescribed time.
We possess the necessary License from the Government of India/State Government for rendering the supplies
/ services.
Dated:……………………………..
Signature and seal of Authorized Signatory
NOTE
1.
2.
3.
4.
5.
The offer must be submitted as per above proforma. The Bidder may use his letterhead to submit his offer.
No erasures or alternations in the text of the offer are permitted.
Any correction made in offer shall be initialed by the Bidder.
VALUES should be both in figures and Words.
The prices quoted should be most competitive
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 29 of 115
LOT - 6 Electronic Trainers
Project: Upgradation & Modernisation of Rajiv Gandhi School of Production and Art, Ulaanbaatar,
Phase – II
Unit FOR
Sl.
Chennai
Annex Ref.
ITEM
Brief Specification
Qty
No
Port Price in
Ind. Rs
1
4/26 &
Oscilloscope - Digital
30 MHz Digital Storage
10
3/2
Oscilloscope
2
3/5
Bread Board trainer with
2
kits
Sets
3
3/22 &
C.R.O. Trainer kit
Bandwidth: 25-30 MHz
4
3/23
4
3/3
Power Supply set
Power Supply Set 0-30V
8
& 0-300V DC
5
3/6
AC Bridge rectifier Trainer
1
6
3/7
TV Trainer kit
LCD/LED Television Trainer
4
7
3/9
Pattern generator
Colour Pattern Generator:
3
8
3/10
Signal generator Am/Fm
Frequency Range: 1 Hz 10 MHz
3
9
3/12
Distortion meter
Frequency: 20 Hz to 20
KHz
1
10
3/13
Strain gauge with load cell
approximately 400 gm
2
11
12
3/15
3/16
DVD Trainer kit
Micro Processor Training
kit
System: PAL, NTSC
1
3
13
3/17
&
4/32
Linear Digital I.C Trainer
5
14
3/19
Frequency Counter
15
3/20
A.F/R.F Oscillator
Digital Circuits to be
covered: Minimum - Basic
logic gates, Universal
gates, Flip-flops, Counters,
Multiplexers
/
Demultiplexers, Encoder /
Decoder, Full/Half Adder
& Substractor.
Frequency range: 10 Hz to
1 GHz with minimum 2
steps, variable control
between steps
Radio Frequency Range:
10 MHz to 150 Mhz
Audio frequency Range:
10 Hz to 20 KHz
16
Function Generator Trainer
Kit
3
17
3/24
&
4/29
3/30
2
18
3/32
Cellular telephone set
trainer
SMPS Trainer
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 30 of 115
3
3
2
Mongolia –
Total FOR
Chennai
Port Price
in Ind. Rs.
Project: Upgradation & Modernisation of Rajiv Gandhi School of Production and Art, Ulaanbaatar,
Phase – II
Unit FOR
Sl.
Chennai
Annex Ref.
ITEM
Brief Specification
Qty
No
Port Price in
Ind. Rs
19
3/35
20
3/36
21
3/37
22
3/41
23
24
25
26
27
3/42
3/43
3/71
3/72
3/89
Electrical & Electronics
system Trainer
Communication system
trainer
EPABX Trainer kit
(Electronic Exchange)
EPROM Kit
A to D Trainer kit
D to A Trainer kit
Transistor Tester
I.C. Tester
A.F. Oscillator
28
3/90
Frequency Modulator
29
30
4/25
4/30
&
3/14
4/31
4/44
Industrial PLC trainer kit
Discrete Component
trainer
31
32
Mongolia –
Total FOR
Chennai
Port Price
in Ind. Rs.
2
2
2
Program
Memory:
Minimum 64 Kb
Display: LCD /LED
Audio frequency: 1 Hz to
1 MHz
Frequency range: 1Hz to
100 KHz
1
1
1
2
2
3
2
1
2
Linear I.C. Trainer
1
Experimental Power
Power Devices : Triac, UJT
1
Electronics Trainer
& SCR
33
4/112
Inverter, sine wave
Power: 1KVA
2
Total FOR Chennai Port Prices in Indian Rupees
Cost towards Installation, Commissioning and training the customer’s personnel in operation and maintenance for
above Pre Printing Equipment at project site in Mongolia.
*Total Indian Rupees (in words)
*Total should include the cost towards the following:
a. Deputation of technical personnel for carrying out installation, commissioning, trials, training the
customer’s personnel in operation and maintenance of above equipment at project site in Mongolia.
b. Necessary tools, fixtures, instruments, trial materials, consumables, etc, for Installation and training have
to be sent along with the supplies.
Please indicate the man day rates considered for deputation on the format given below
Sl No.
No. of Persons required for Installation, No. of Man days Cost per man day
Commissioning & Training of LOT 3 equipment
required
(In Rs.)
It is hereby certified that we have understood the instruction to Bidders and also the Terms & Conditions of
Contract attached to the tender and have thoroughly examined and are aware of the nature of
supplies/services required and our offer is to render supplies/services strictly in accordance with the
requirements and according to the terms of the tender. We agree to abide solely by the terms & conditions of
contract and other conditions of the tender in accordance with the tender documents if the contract is
awarded to us.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 31 of 115
We hereby offer to render supplies/ services as detailed above or such portion thereof as you may specify in
the acceptance of tender at the price quoted and agree to hold this offer open for acceptance for a period of
90 days from the date of opening of tender. We shall be bound by the communication of acceptance
dispatched within the prescribed time.
We possess the necessary License from the Government of India/State Government for rendering the supplies
/ services.
Dated:……………………………..
Signature and seal of Authorized Signatory
NOTE
6.
7.
8.
9.
10.
The offer must be submitted as per above proforma. The Bidder may use his letterhead to submit his offer.
No erasures or alternations in the text of the offer are permitted.
Any correction made in offer shall be initialed by the Bidder.
VALUES should be both in figures and Words.
The prices quoted should be most competitive
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 32 of 115
LOT - 7 Electrical Meters
Project: Upgradation & Modernisation of Rajiv Gandhi School of Production and Art, Ulaanbaatar, Mongolia – Phase
– II
Unit FOR
Total FOR
Make
Chennai Port
Sl.
Annex
Brief
Chennai Port
ITEM
Qty
No
Ref.
Specification
Price in Ind.
Price in Ind. Rs.
Rs
1
4/85 &
Digital Multi
ISI STANDARD
18
3/48
meter
2
3/53
Digital Ohm
Upto 10 M.ohm ISI STANDARD
2
meter
range
3
4/114 & Rheostats - set
MEC/
4 sets
3/68
TOSHNIWAL/
ISI
STANDARD
4
3/73
DC/AC
Ammeter
DC AE / MECO /
3
Ammeter
Digital portable ELC /
type, 0-5 A range. UNITECH/
Ammeter
AC INDOTECH/
3
Digital portable ISI STANDARD
type, 0-5 A range.
5
6
7
8
3/74
3/75
3/76
3/77
DC/AC
Ammeter
DC/AC
Ammeter
DC/AC
Ammeter
DC/AC
Ammeter
Ammeter
DC
Digital portable
type, 0-500 mA
range.
Ammeter
AC
Digital portable
type, 0-500 mA
range.
Ammeter
DC
Digital portable
type,
0-1 mA
range.
Ammeter
AC
Digital portable
type,
0-1 mA
range.
Ammeter
DC
Digital portable
type, 0-5 mA
range.
Ammeter
AC
Digital portable
type, 0-5 mA
range.
Ammeter
DC
Digital portable
type, 0-100 mA
range.
Ammeter
AC
AE / MECO /
ELC /
UNITECH/
INDOTECH/
ISI STANDARD
AE / MECO /
ELC /
UNITECH/
INDOTECH/
ISI STANDARD
AE / MECO /
ELC /
UNITECH/
INDOTECH/
ISI STANDARD
AE / MECO /
ELC /
UNITECH/
INDOTECH/
ISI STANDARD
3
3
3
3
3
3
3
3
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 33 of 115
Project: Upgradation & Modernisation of Rajiv Gandhi School of Production and Art, Ulaanbaatar, Mongolia – Phase
– II
Unit FOR
Total FOR
Sl.
Annex
Brief
Make
Chennai Port
ITEM
Qty
Chennai Port
No
Ref.
Specification
Price in Ind.
Price in Ind. Rs.
Rs
Digital portable
type, 0-100 mA
range.
9
3/78
DC/AC
Voltmeter DC/AC, AE / MECO /
3
Voltmeter
Digital portable ELC /
type, 0-5 V range UNITECH/
INDOTECH/
ISI STANDARD
10
3/79
DC/AC
Voltmeter DC/AC, AE / MECO /
3
Voltmeter
Digital portable ELC /
type 0-10 V range UNITECH/
INDOTECH/
ISI STANDARD
11
3/80
DC/AC
Voltmeter DC/AC, AE / MECO /
3
Voltmeter
Digital portable ELC /
type 0-50 V range UNITECH/
INDOTECH/
ISI STANDARD
12
3/81
DC/AC
Voltmeter DC/AC, AE / MECO /
3
Voltmeter
Digital portable ELC /
type
0-500 V UNITECH/
range
INDOTECH/
ISI STANDARD
13
4/41
M.C.B
MDS /
2 sets
SIEMENS /
GLOSTAR/
ISI STANDARD
14
4/84
Analog multi
AE / MECO /
4
Meter
PROTECT /
METRAVI /
MASTECH/
ISI STANDARD
15
4/86
A.C. Voltmeter,
AE / MECO /
2
MI
ELC / NIPPEN
/ BRISTEL /
UNITECH
/INDOTECH/
ISI STANDARD
16
4/87
Milli Voltmeter 100 – 0 -100
AE / MECO /
2
centre zero
millivolts,
ELC / NIPPEN/
ISI STANDARD
2
17
4/88
D.C Milli
0 - 500 mA
AE / MECO /
ammeter
ELC / NIPPEN/
ISI STANDARD
18
4/89
D.C. Ammeter
0 – 1 A,MC,
AE / MECO /
2
MC
ELC / NIPPEN/
ISI STANDARD
19
4/90
Ammeter MC
Portable, MC,
AE / MECCO /
2
Range: 0-5 A
UNITECH
/INDOTECH/
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 34 of 115
Project: Upgradation & Modernisation of Rajiv Gandhi School of Production and Art, Ulaanbaatar, Mongolia – Phase
– II
Unit FOR
Total FOR
Sl.
Annex
Brief
Make
Chennai Port
ITEM
Qty
Chennai Port
No
Ref.
Specification
Price in Ind.
Price in Ind. Rs.
Rs
ISI STANDARD
20
4/91
Ammeter MC
Portable, MC,
AE / MECCO /
2
Range: 0-15-25 A UNITECH/
INDOTECH/
ISI STANDARD
21
4/92
A.C. Ammeter
Portable , MI,
MECO / EIC /
2
MI
Range 0-5 A
NIPPEN /
BRISTEL/
ISI STANDARD
22
4/93
A.C. Ammeter
Portable, MI,
MECO / EIC /
2
MI
Class-1, Multi
NIPPEN /
Range
BRISTEL/
0-15-25 A
ISI STANDARD
23
4/94
K.W. Meter
AE / MECO /
2
ECI / NIPPEN /
INDOTECH/
ISI STANDARD
24
4/95
A.C. Energy
TECHNO /
2
Meter
UNITECH
/INDO TECH/
ISI STANDARD
25
4/96
Single Phase
AE / MECCO/
2
power factor
EIC / NIPPEN /
meter
INDOTECH /
MEC/
ISI STANDARD
26
4/97
Frequency
ISI STANDARD
2
Meter
27
4/99
Growler
Inside & Outside
MASTECH/
2 set
Growler set
MEC/
ISI STANDARD
28
4/100
Tong tester/
0 - 5 -10 Amps,
ISI STANDARD
2
Clamp meter
29
4/101
Megger set
Megger set of
WACO/MAST
2 sets
range 500 Volts & ECH/
1000Volts
ISI STANDARD
30
4/123
Flux meter
Digital flux meter ISI STANDARD
2
31
4/124
Lux meter
Lux meter
KUSUM/MAS
2
TECH/
LUTRON/
ISI STANDARD
32
4/157
Clamp on
Digital Clamp
KUSAM –
3
Ammeter
meter
MECO/
ISI STANDARD
Total FOR Chennai Port Prices in Indian Rupees
Total Indian Rupees (in words)
It is hereby certified that we have understood the instruction to Bidders and also the Terms & Conditions of
Contract attached to the tender and have thoroughly examined and are aware of the nature of
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 35 of 115
supplies/services required and our offer is to render supplies/services strictly in accordance with the
requirements and according to the terms of the tender. We agree to abide solely by the terms & conditions of
contract and other conditions of the tender in accordance with the tender documents if the contract is
awarded to us.
We hereby offer to render supplies/ services as detailed above or such portion thereof as you may specify in
the acceptance of tender at the price quoted and agree to hold this offer open for acceptance for a period of
90 days from the date of opening of tender. We shall be bound by the communication of acceptance
dispatched within the prescribed time.
We possess the necessary License from the Government of India/State Government for rendering the supplies
/ services.
Dated:……………………………..
Signature and seal of Authorized Signatory
NOTE
11.
12.
13.
14.
15.
The offer must be submitted as per above proforma. The Bidder may use his letterhead to submit his offer.
No erasures or alternations in the text of the offer are permitted.
Any correction made in offer shall be initialed by the Bidder.
VALUES should be both in figures and Words.
The prices quoted should be most competitive
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 36 of 115
Annexure – 2
PROFORMA FOR STATEMENT OF DEVIATIONS FROM TENDER CONDITIONS
The following are the particulars of deviations from the requirements of the Instructions to Bidders and Terms & Conditions
of contract (To be enclosed for each lot separately): CLAUSE
DEVIATION
REMARKS
(Including justification)
…………………………………….
Signature and seal of
the Authorized Signatory
NOTE: Where there is no deviation, the statement should be returned duly
signed with an endorsement indicating “No Deviations”.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 37 of 115
Annexure – 3
PROFORMA FOR COMMERCIAL DETAILS & PREVIOUS EXPERIENCE
(i)
Is the firm registered with Govt. Authority/ Agency or MNC? If so, a copy of the registration certificate should be
enclosed.
(ii)
Name and address of the Banker
Details of major orders for the quoted supplies/services executed during the past three years should be furnished in the
following format.
Sl. #
Full Address of
Customer
Order No.
and Date
1
2
3
Description
Supplies
Services
4
of
/
Qty.
Contract
Value in Rs.
Remarks
5
6
7
Signature:…………………………..
Name:………………………………..
Designation:……………………….
NOTE: A certificate from the customer should preferably be enclosed to indicate that the contract was satisfactorily performed.
To be enclosed for each lot separately.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 38 of 115
Annexure – 4
PROFORMA FOR PERFORMANCE BANK GUARANTEE
THE GENERAL MANAGER, PROJECTS
HMT (INTERNATIONAL) LTD.
HMT BHAVAN
59 BELLARY ROAD
BANGALORE – 560 032
DEAR SIR,
THIS DEED OF GUARANTEE EXECUTED BY …………………………………… BANK, (NAME AND ADDRESS OF THE BANK) (HEREINAFTER
REFERRED TO AS BANK) IN FAVOUR OF HMT (INTERNATIONAL) LTD. (HEREINAFTER REFERRED TO BENEFICIARY) NOT EXCEEDING
RS………. (RUPEES ………….. ONLY) AT THE REQUEST OF M/S. ……………………….. (HEREINAFTER REFERRED TO AS SUPPLIER).
WHEREAS THE SUPPLIER HAS APPROACHED BANK TO ISSUE BANK GUARANTEE IN YOUR FAVOUR FOR A SUM OF RS. ……………. (RUPEES
…………….. ONLY). WHEREAS THE SUPPLIER HAS RECEIVED PURCHASE ORDER NO. ………………….
……………………….
DATED ……………….
FOR RS
FOR PROVIDING SERVICES AS STATED IN THE PURCHASE ORDER. WHEREAS THE SUPPLIER HAS TO
SUBMIT PERFORMANCE GUARANTEE FOR TEN PERCENT OF THE VALUE OF SUPPLIES PORTION OF RS……………………………….AS STATED IN
THE SAID PURCHASE ORDER.
WE HEREBY CONFIRM AND STATE THAT WE AS GUARANTORS SHALL BE RESPONSIBLE TO YOU ON BEHALF OF THE “SUPPLIER” FOR A
TOTAL SUM OF RS………………… (RUPEES …………………………. ONLY) IN CASE OF VIOLATION OF ANY OF THE TERMS/CONDITIONS OF THE
SAID PURCHASE ORDER.
WE UNDERTAKE TO PAY YOU UPON FIRST WRITTEN DEMAND DECLARING THE “SUPPLIER” TO BE IN VIOLATION/BREACH OR
CONTRAVENTION OF ANY OF THE TERMS AND CONDITIONS, WITHOUT DEMUR OR ARGUMENT OR COURT ORDER OR RESOLUTION
WITHIN THE VALIDITY OF THIS GUARANTEE, A SUM OF RS………………… (RUPEES ……………….. ONLY) AS AFOREMENTIONED WITHOUT
YOUR HAVING TO PROVE TO US OR TO SHOW GROUNDS OR REASONS FOR YOUR DEMAND FOR THE SUM SPECIFIED HEREIN.
THE GUARANTEE CONTAINED HEREIN SHALL NOT BE AFFECTED BY ANY CHANGES IN THE CONSTITUTION OF THE BANK OR IN THE
CONSTITUTION OF THE BENEFICIARY VIZ. YOURSELF AND SHALL BE VALID TILL
(DATE)
FROM THE DATE OF ISSUE PROVIDED
HOWEVER THAT IN CASE DEMAND IS NOT MADE BY YOU UNDER THIS GUARANTEE ON OR BEFORE
(DATE) , BANK SHALL BE FULLY
ABSOLVED FROM ANY LIABILITY UNDER THIS GUARANTEE DEED.
WE HEREBY DECLARE AND STATE THAT THIS GUARANTEE UNLESS INVOKED BY YOU AS AFORESAID SHALL BE VALID TILL (DATE) FROM
THE DATE OF ISSUE AND SHALL BE NULL AND VOID THEREAFTER WHETHER THE ORIGINAL GUARANTEE IS RETURNED OR NOT
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 39 of 115
Annexure – 5
PROFORMA FOR VENDOR APPRAISAL
General Information
Vendor Code
1.
Company
M/s.
Phone:
Fax:
E-Mail:
City:
PIN:
2.
Web Site:
Contact Person
Name:
Designation:
E-Mail:
6.
Phone:
3.
Number of Years in Business :
4.
Number of Units :
5.
Total Number of Employees :
Major Customers
1)
4)
2)
5)
3)
6)
Y
7.
Sales Office/Authorized Distributor
If yes Indicate details below
A
M/s.
M/s.
PIN
PIN
Phone:
Phone:
Fax:
Fax:
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 40 of 115
N
C
E-Mail
E-Mail
M/s.
M/s.
PIN
PIN
Phone:
Phone :
Fax :
Fax :
E.Mail
E.Mail
Production & Service Capabilities
1
Product Range
a
f
b
g
c
h
d
I
e
j
2
Processes Existing in the Plant
Processes
1
2
3
4
5
6
7
8
Availability
Details
Conventional Machining
Y
N
Y
N
Y
N
Y
N
Y
N
Y
N
Y
N
Y
N
Y
N
Y
N
N.A
CNC Machining
Forging
Casting
Plating
Fabrication
Tool Making
Welding
9
Gear Manufacturing
10
Designing
Quality Information
1
Control adopted
Details
a
In-Process Inspection
b
Stage Inspection
Y
N
Y
N
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 41 of 115
c
Testing
Y
N
d
SQC/SPC
Y
N
2
Inspection & Testing Facility Available
Details
a
Material Testing
Y
N
b
Precision Measurement
Y
N
c
Furnace Testing
Y
N
d
Non-Destructive Testing
Y
N
e
Calibration
Y
N
3
Quality System Implemented-ISO 9000/QS 9000
Y
N
4
Capability to supply products with CE Marking
Y
N
5
Quality Level of Existing Products
Enclose Certificate
1
2
3
4
5
Poor
Fair
Good
Very Good
Excellent
Commercial & Financial Information
2011-12
1
2012-13
Annual Turnover for last 3 Years in Rs.Lakhs
Net Profit for the last 3 years Rs. Lakhs
2
Y
Exports
N
If Yes, Turnover for last 3 Years in Rs.Lakhs
3
Specify Countries to which Exports are made
USA
UK
Europe
Middle East
CIS Countries
Others
4
Any Collaboration
Y
N
If Yes, Indicate Details
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 42 of 115
2013-14
5
Any investment Envisaged for Expansion
Y
N
6
Is company following Direct Procurement Principle
Y
N
7
KST / CST Registration No.
8
Central Excise
No
Range
9
SSI Registration No.
10
Do you have Company Brochure
Y
N
11
Experience in handling Government of India's projects
Y
N
Y
N
If yes, value of projects executed so far Rs. Lakhs
12
Is the company registered with MEA ?
If Yes, Value of Supply done to MEA Projects
Direct supply
Thru Agency
Rs. Lakhs
13
Y
Supplies done to HMT(I)
If Yes, Value of Supplies done Rs. Lakhs
Details of supplies to HMT(I):
Compiled by:
Signature:
Name:
Date
Note:
1
Put √ in appropriate check box.
2
If space provided is not sufficient to provide details, please attach extra sheet.
3
Please attach catalogue/Brochure if available.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 43 of 115
N
Annexure - 6
PROFORMA FOR VENDOR REGISTRATION
S.N.
Description
Details
(a) Name and address of the vendor
(b) Please specify whether you are : Manufacturing Unit / Distributor / Agent etc.,
1
(c) Telephone No.
(d) Fax No.
(e) Email ID
(f) Company Profile (Please enclose)
(g) Turnover of the Company for the past three years
(h) Bankers Details
2
Quality system implemented - ISO 9000 / QS 2000 etc.
3
Name, address & Telephone No. of the owner / proprietor/partners
4
Sales Tax Registration No. - Central & State
6
Registration No.
7
Details of Products Manufactured / Distributed / offered. Please enclose brochure.
8
Details of Manufacturing Units / Workshops etc., available
9
Details of Machines, equipment, computers available
10
Manpower / Organization structure
11
List of Major Products / Services
12
Details of your major customers
13
Are you exporting Products / services? If so, please furnish
details of exports for past 3 years.
14
Are you providing training to overseas students/trainers and if so,
give details of the training courses conducted for last 3 years
15
Do you have branches or institutes under your group, If yes,
give details with address.
16
Whether you are affiliated / accredited to any Govt.
Agency / Reputed organization
Declaration: I / We declare that the details given above are true and correct.
Place :
Signature of Authorized person
Date :
(Note: Please attach detailed information in a separate sheet wherever required)
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 44 of 115
With Company Seal
ANNEXURE – 7
PROFORMA FOR BANK GUARANTEE FOR BID GUARATNTEE
To,
The General Manager (Projects)
HMT (International) Limited
HMT Bhavan, No.59, Bellary Road
BANGALORE – 560 032
Dear Sir,
In accordance with your invitation to tender No…………………………………..M/s. …………………………………………………………. hereinafter called
the bidder with the following Directors on their Board of Directors/Partners of the firm:
1.
2.
3.
4.
5.
wish to participate in the said tender for supplying Machine / equipment required for RGSPA Project at Ulaanbaatar, Mongolia being
implemented by HMT (International) Limited, Bangalore.
As a Bank Guarantee against Bid Guarantee for a sum of Rs…………(in words & figures) valid for 90 days from the date of opening of the
Tender No…………………… is required to be submitted by the bidder as a condition for the participation, this bank hereby guarantees and
undertakes during the above said period of 90 (Ninety) days to immediately pay, on demand by HMT (International) Limited,
Bangalore in writing the amount of Rs…… (words & figures) to HMT (International) Limited, Bangalore without any reservation and
recourse, if:
1)
2)
3)
The bidder after submitting his tender, modifies the rates or any of the terms and conditions thereof, except with the
previous written consent of the purchaser or
The bidder withdraws the said bid within 90 days after opening of bid or
The bidder having not withdrawn the bid, fails to furnish the contract of Performance Guarantee within the period
provided in the terms and conditions of the contract.
This guarantee shall be irrevocable and shall remain valid up to 4.00 p.m. on……………………………..if further extension to this guarantee
is required, the same shall be extended to such required periods on receiving instructions from M/s………………………………………………on
whose behalf this guarantee is issued.
Date………………….
Signature………………………..
Place…………………..
Printed Name…………………..
Witness
1.………………………..
……………………………………………………..
(Designation)
2………………………….
(Bank’s Common Seal)
(Note : This should be on bidders letter head)
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 45 of 115
ANNEXURE – 8
QUALITY AND PACKING DETAILS
1.
MACHINE / EQUIPMENT:
1.1
Machine / Equipment shall be manufactured and delivered in accordance with the specifications as given in this Tender and quality shall be as
per Indian / International Standards.
Goods supplied shall be new, genuine, unused and shall be of current models and of current productions.
Any alteration to the specifications, Design, Patterns etc. of the offered goods shall only be made upon the Buyer’s consent in writing.
The Tenderer warrants that the materials, metals, chemicals, paints, packing pieces etc. used in the manufacture of goods and all its packing
and packaging are fully trivialized and stable under tropical conditions. Any damages arising from the inadequate trivialization, shall be deemed
an inherent defects of manufacture.
1.2
1.3
1.4
1.5
BOUGHT-OUTS:
All the bought-out items such as bearings, belts, electricals, motors, contactors, switches, MCBs, fuses, transformers, rubber gaskets, O-rings,
conduit pipes, coolant and hydraulic hoses etc. shall correspond to ISI / International specifications, should preferably have CE mark and shall
be of reputed make like SKF, FENNER, BHARAT, BIJILEE, CUTTLER HAMMER, CROMPTON GREAVES, SIEMENS and TELEMECHNIC.
1.6
Bought-out accessories like Furnace Lamps, pumps, Panel Air conditioners, Oil Coolers, Panel Boards, Stabilizers, Transformers etc. should be
from reputed original equipment manufacturers.
1.7
Machine / Equipment aesthetics especially sheet metals, guards, doors, covering plates, castings are to be made to international standards.
Painting and finish of Furnaces are the most important aspects of aesthetics.
2.
INSTRUCTION & SPARE PARTS MANUALS:
2.1
Neatly printed manuals should be sent with the Machine / Equipment. Instruction Manuals should be of updated version containing complete
details of offered Machine / Equipment including customer name, Machine / Equipment number, Machine / Equipment model, year of
manufacture etc..
Drawings should be clear and legible. Xerox copies are not acceptable. Details of bought-out items used in the Machine/Equipment should be
included in the manual. Good quality paper should be used for printing of manuals.
All foundation drawings showing electrical, air, water and other service connections of Machine / equipment, with floor plans to be provided in
two sets, in English.
2.2
2.3
3.
SAFETY DEVICES:
Each Machines/equipment should be provided with adequate and all necessary safety devices for the protection of the operator/s, factory
personnel and the environment.
4.
OTHER CONDITIONS:
Since Machine / Equipment are being exported, Machine / Equipment including all accessories have to be built to ensure high quality
performance, aesthetic appearance in respect of general finish, painting, sheet metal fabrication and international safety regulations.
5.
PACKING INSTRUCTIONS:
5.1
5.2
5.3
Export worthy wooden / plywood packing as per Indian / International standards suitable for sea freight.
Equipment, accessories and spares are to be covered by thick silpaulin sheet or 1 mm thick polythene sheets and all openings are to be sealed .
All external bright / machined surfaces should be protected with coating of OKS-CORTEC VCI 369 N Rust preventive. OKS rust preventive to be
used.
Rust preventives to be used whose shelf life is not less than one year.
Packing list with respect to each case to be prepared and given to HMT(I) along with other documents.
Machine / Equipment should be firmly fixed to be base of packing case to prevent jerking or local movement.
Delivery Voucher should clearly indicate packing case dimension with net and Gross weight and case number if there are more than one case.
Photographs before and after packing to be taken and sent to HMT(I).
Handling marks of the packing cases to be shown on packing cases.
5.4
5.5
5.6
5.7
5.8
5.9
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 46 of 115
Enclosure – I
LOT-1 MACHINE TOOLS:
1. PILLAR TYPE DRILLING MACHINE – TYPE-1:
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Ref No. : 4/45 - Annexure 4
Sl. No.
Item
Brief Specification
Quantity
1
1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
1.11
1.12
1.13
2
2.1
2.2
2.3
2.4
2.5
2.6
2.8
3
4
5
Pillar Type Drilling Machine with all standard accessories and Electrical suitable for
380V, 3Phase, 50Hz AC supply and control Voltage 230V, 1 phase AC supply. MCB’s to be
used in place of fuses
Major specifications
Drilling capacity in steel / MT in spindle
20 mm / MT2
Tapping Capacity
M12
No./Range of spindle speeds
10/ 100-2700 rpm
Feed
Hand
Spindle traverse (Approx)
125 mm
Pillar diameter
>75 mm
Max. distance b/w center of spindle and
200 mm
column front
Max. distance b/w spindle and table
300 mm
Max. distance b/w spindle and base
600 mm
Table working surface diameter (Min)
370 mm
Base dimension (Approx)
385 x 375 mm (DxW)
Motor Power
0.75 kW
Coolant Motor Power
0.1 kw
Dual colour: Soft Grey (RAL-7035) and Himmel
Colour of the Machine:
Blue (RAL-5015) Polyurethane Paint
Required Accessories / Spares
Coolant pump motor and pipe fittings
Halogen machine lamp
Drill chuck 19 mm with key and arbor
Machine vice 4” swivel base with ‘T’ bolts
Reduction sleeve MT2-MT1
Service Tool Kit
DOL starter
Set of mechanical and electrical spare parts for 2 year normal operation. (Item wise
quantity with price to be provided)
Operation, Maintenance and spare parts manual
Items required for erection and
• Touch up paint - 1/2 litre each colour in
commissioning
airtight sealed containers, Paint brush
½” 1 no. for each colour
• Initial fill of
Hydraulic/Lubrication/Cutting Oil, if any
in separate sealed containers.
• Cotton waste- 2 kg, Cora cloth – 5 Mtrs
• Foundation bolts and leveling plates.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 47 of 115
2
1 set each
1 set each
1 set each
1 no. each
1 set each
1 set each
1 set each
1 set each
3 sets each
1 set each
2. PILLAR TYPE DRILLING MACHINE – TYPE-2:
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Ref No. : 6/13 of Annexure 6
Sl. No.
Item
Brief Specification
Quantity
1
1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
1.11
1.12
1.13
2
2.1
2.2
2.3
2.4
2.5
2.6
3
4
5
Pillar type Drilling Machine with all standard accessories and Electrical suitable for
380V, 3 Phase, 50cy AC supply and control Voltage 230V, 1 phase AC supply. MCB’s to be
used in place of fuses
Major specifications
Drilling capacity in steel / MT in spindle
13 mm / MT1
No./Range of spindle speeds
4/ 480-2080 rpm
Feed
Hand
Spindle traverse (Approx)
100 mm
Pillar diameter (Approx)
55 mm
Max. distance b/w center of spindle and
140 mm
pillar front
Max. distance b/w spindle and table
300 mm
Max. distance b/w spindle and base
930 mm
Table working dimension (Approx)
200 x 200 mm
Base dimension (Approx)
285 x 305 mm (DxW)
Motor Power
0.37 kW
Coolant Motor Power
0.1 kw
Dual colour: Soft Grey (RAL-7035) and Himmel
Colour of the Machine:
Blue (RAL-5015) Polyurethane Paint
Required Accessories / Spares
Coolant pump motor and pipe fittings
Halogen machine lamp
Drill chuck 13 mm with key and arbor
Machine vice 4” swivel base with ‘T’ bolts
Service Tool Kit
DOL starter
Set of mechanical and electrical spare parts for 2 year normal operation. (Item wise
quantity with price to be provided)
Operation, Maintenance and spare parts manual
Items required for erection and
• Touch up paint - 1/2 litre each colour in
commissioning
airtight sealed containers, Paint brush
½” 1 no. for each colour
• Initial fill of
Hydraulic/Lubrication/Cutting Oil, if any
in separate sealed containers.
• Cotton waste- 2 kg, Cora cloth – 5 Mtrs
• Foundation bolts and leveling plates.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 48 of 115
1
1 set
1 set
1 set
1 no.
1 set
1 no
1 set
3 sets
1 set
3. PEDESTAL GRINDING MACHINE:
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Ref No. : 6/9 of Annexure 6
Sl. No.
Item
Brief Specification
Quantity
1
1
1.1
1.2
1.3
1.4
1.5
1.6
2
2.1
2.2
2.3
2.4
3
4
5
Pedestal Grinding Machine with all standard accessories and Electrical suitable for 380V,
3Phase, 50cy AC supply and control Voltage 230V, 1 phase AC supply. MCB’s to be used in
place of fuses
Major specifications
Double ended with dynamically balanced motor with wheel guards having removable end
caves
Centre distance between wheels (Approx)
420 mm
Height from Base to spindle centre (Approx) 910 mm
Wheel speed (Approx)
2860 rpm
Motor Power
0.6 kW
Grinding Wheel size
200 x 25 x 19.05 mm
Dual colour: Soft Grey (RAL-7035) and
Colour of the Machine:
Himmel Blue (RAL-5015) Polyurethane Paint
Required Accessories / Spares
DOL starter
Spark protectors
Spare vitrified bonded grinding wheels
Service Tool set
Set of mechanical and electrical spare parts for 2 year normal operation. (Item wise quantity
with price to be provided)
Operation, Maintenance and spare parts manual
Items required for erection and
• Touch up paint - 1/2 litre each colour
commissioning
in airtight sealed containers, Paint
brush ½” 1 no. for each colour
• Initial fill of
Hydraulic/Lubrication/Cutting Oil, if
any in separate sealed containers.
• Cotton waste- 2 kg, Cora cloth – 5
Mtrs
• Set of anti vibration pads/Foundation
bolts and leveling plates.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 49 of 115
1
1 each
1 set each
5 nos each
1 set each
1 set each
3 sets each
1 set each
Enclosure – II
LOT-2 WELDING EQUIPMENT:
1. WELDING TRANSFORMER:
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Item : WELDING TRANSFORMER
Ref. No: 6/17 of Annexure 6
Qty : 4 Nos
Sl.
No.
Description
1
WELDING TRANSFORMER:
Welding transformer complete unit operating with 3 phase, 380V, 50 Hz AC, along with indefinitely variable
current regulator of 40 to 300 A, mounted on suitable Castor wheels as per the following specifications.
All the three phases are to draw current form the lines according to the load and should not draw a fixed current
with load or without load.
Open Circuit voltage to be atleast 80V for efficient arc striking.
The transformer should supply the required output and be able to dissipate its heat naturally without the use of
external fans.
BRIEF SPECIFICATION:
INPUT POWER:
Primary Voltage/ Phase / Frequency: 380 V, 3 Phase, 50Hz
Input power @ 100% Duty Cycle: 12 KVA
Input Switch Fuse Rating: 50 A
OUT PUT POWER:
Open Circuit Voltage: 80 V
Open Arc Voltage 22: 32 V
Welding Current Range: 40 -300 A
Max. Hand Welding Current @ 60% Duty Cycle: 300 A
Max. Continuous Welding Current @ 100% Duty Cycle welding: 180 A
Welding Electrode Range:2.0 -5.0 mm
GENERAL:
Type of cooling : Natural Air
Class of Insulation: H
Protection Class: IP 23
ACCESSORIES TO BE SUPPLIED ALONG WITH EACH EQUIPMENT-EACH SET CONTAINING FOLLOWING
Welding cable - 5 Meters length
1 No.
Electrode holder
2 Nos.
Earth cable – 5 Meters length
1 No.
Earthing clamp
1 No.
Welders cap
2 Nos.
Head shield
1 No.
Black glass
1 No.
Plain glass
2 Nos.
Hand gloves
1 Pair
Leg guard
1 Pair
Chipping hammer
1 No.
Wire brush
1 No.
Container bag
1 No.
General purpose Welding electrodes 20kg box
5 Boxes
SET OF SPARES FOR 2 YEARS OF NORMAL OPERATION (EACH EQUIPMENT 1 SET) Please Indicate the
1 No.
detailed list of spares with individual prices
Operation/ Service/ Spare parts manual – 2 sets to be sent along with Machine and 1 set to HMTI,
1 No.
Bangalore
a.
b.
c.
1.10
1.11
a.
b.
c.
1.12
a.
b.
c.
d.
e.
f.
1.13
a.
b.
c.
1.20
1.21
1.22
1.23
1.24
1.25
1.26
1.27
1.28
1.29
1.30
1.31
1.32
1.33
1.34
1.30
1.40
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 50 of 115
2. WELDING TRANSFORMER
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Item : WELDING TRANSFORMER
Ref. No: 6/18 of Annexure 6
Qty : 4 Nos
Sl. No.
Description
1
a.
b.
c.
1.10
1.11
a.
b.
c.
1.12
a.
b.
c.
d.
e.
f.
1.13
a.
b.
c.
1.20
1.21
1.22
1.23
1.24
1.25
1.26
1.27
1.28
1.29
1.30
1.31
1.32
1.33
1.34
1.40
1.41
1.50
WELDING TRANSFORMER: Welding transformer complete unit operating with 3 Ph, 380V, 50 Hz
AC, along with indefinitely variable current regulator of 40 TO 400A mounted on suitable caster
wheels as per the following specifications.
All the three phases are to draw current form the lines according to the load and should not
draw a fixed current with load or without load
Open Circuit voltage to be atleast 80V for efficient arc striking.
The transformer should supply the required output and be able to dissipate its heat naturally
without the use of external fans.
BRIEF SPECIFICATION:
INPUT POWER:
Primary Voltage / Phase / Frequency : 380v / 3phase / 50 Hz
Input Power @ 100% Duty Cycle - 15 KVA
Input Switch Fuse Rating – 60 A
OUT PUT POWER:
Open Circuit Voltage – 82 V
Open Arc Voltage – 22 – 36 V
Welding Current Range – 70 to 400 A
Max. Hand Welding Current @ 60% Duty Cycle – 400 A
Max. Continuous Welding Current @ 100% Duty Cycle – 240 A
Welding Electrode Range – 2.5 to 6.3 mm
GENERAL:
Type of cooling – Natural Air
Class of Insulation – H
Protection Class – IP 23
ACCESSORIES TO BE SUPPLIED ALONG WITH EACH EQUIPMENT-EACH SET CONTAINING
FOLLOWING
Welding cable – 5 meters
1 No.
Electrode holder
2 Nos.
Earth cable – 5 meters length
1 No.
Earthing clamp
1 No.
Welders cap
2 Nos.
Head shield
1 No.
Black glass
1 No.
Plain glass
2 Nos.
Hand gloves
1 Pair
Leg guard
1 Pair
Chipping hammer
1 No.
Wire brush
1 No.
Container bag
1 No.
General purpose Welding electrodes-20kg box
5 Boxes
SET OF SPARES FOR 2 YEARS OF NORMAL OPERATION (EACH EQUIPMENT 1 SET)
Please Indicate the detailed list of spares with individual prices
Operation/ Service/ Spare parts manual – 2 sets to be sent along with Machine
and 1 set to HMTI, Bangalore
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 51 of 115
1 No.
3. WELDING RECTIFIER
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Item : WELDING RECTIFIER
Ref. No: 6/91 of Annexure 6
Qty : 1 No
Sl. No.
Description
1
a.
b.
c.
d.
e.
1.10
1.11
a.
WELDING RECTIFIER:
Welding rectifier complete unit operating with 3 Ph, 380V, 50 Hz AC, diode based with output
current range up to 600A mounted on suitable wheels for easy manuorability as per the
following specifications.
The rectifier should have 3phase full wave bridge rectifier with a perfectly balanced transducer
and output choke.
Overload breaker to be fitted for control circuit for switch resetting.
Built in Hot start with provision to adjust the percentage of hot start for specific electrodes.
Transformer and magnetic amplifier to be of separate construction.
Remote amperage control on a 3pin connector with switch for selection.
BRIEF SPECIFICATION:
INPUT POWER:
Primary Voltage /Phase / Frequency: 380V/3 phase/50 Hz
b.
c.
1.12
a.
Input Power @ 100% Duty Cycle: 35 KVA
Input current @ 100% Duty Cycle: 50 A
OUTPUT POWER:
Open Circuit Voltage: 80 V
b.
c.
d.
e.
1.13
a.
b.
Welding Current Range: 60 – 600 A
Max. Welding Current @ 60% Duty Cycle: 600 A
Max. Welding Current @ 100% Duty Cycle: 465 A
Welding Electrode Range: 2– 6.3 mm
GENERAL:
Type of cooling: Forced Air
Class of Insulation: H
c.
1.20
Protection Class: IP23
ACCESSORIES TO BE SUPPLIED ALONG WITH EACH EQUIPMENT-EACH SET CONTAINING
FOLLOWING:
Welding cable – 5 meters
1 No.
Electrode holder
2 Nos.
Earth cable – 5 meters
1 No.
Earthing clamp
1 No.
Welders cap
2 Nos.
Head shield
1 No.
Black glass
1 No.
Plain glass
2 Nos.
Hand gloves
1 Pair
1.21
1.22
1.23
1.24
1.25
1.26
1.27
1.28
1.29
1.30
1.31
1.32
1.33
1.34
1.40
1.41
1.50
Leg guard
Chipping hammer
Wire brush
Container bag
General purpose Welding electrodes, 20kg box
SET OF SPARES FOR 2 YEARS OF NORMAL OPERATION ( EACH EQUIPMENT 1 SET)
Please Indicate the detailed list of spares with individual prices
Operation/ Service/ Spare parts manual – 2 Sets to be sent along with Machine
and 1 Set to HMTI, Bangalore.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 52 of 115
1 Pair
1 No.
1 No.
1 No.
5 Boxes
1 No.
4. SPOT WELDING MACHINE:
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Item : SPOT WELDING MACHINE
Ref. No: 6/20 of Annexure 6
Qty : 1 No
Sl. No.
Description
1
1.10
1.11
SPOT WELDING MACHINE:
Spot Welding Machine/Equipment complete unit operating across 2 phase, 380 V,50 Hz AC,
rated 25 KVA equipped with a 4 function synchronous CMOS IC control & Thyristor panel
including all standard accessories as per following specifications and accessories.
BRIEF SPECIFICATION:
INPUT POWER:
a.
b.
c.
1.12
a.
b.
c.
d.
e.
f.
g.
1.20
Power supply: 380 V
Phase / Frequency: 2 phase / 50 Hz
Rating @ 50% Duty Cycle: 25 KVA
MACHINE / EQUIPMENT DATA:
Throat depth: 450 mm
Rating @ 50% Duty Cycle: 25 KVA
Max secondary short circuit current at throat depth 450 mm: 14 KA
Standard stroke: 50 mm
Throat gap: 315 mm
Max electrode force at 5.6 Kg/cm2: 440 kg
Weld cylinder dia: 100 mm
ACCESSORIES TO BE SUPPLIED ALONG WITH MACHINE / EQUIPMENT
1.21
1.22
1.23
1.24
1.25
1.26
1.27
1.28
1.29
1.30
1.31
4.40
Welding Electrodes
Air Valve
Filter Regulator & Lubricator (FRL)
Copper Flex
Thyristor
Seal kit
Filter card
24 V DC Air valve coil (1/4 ” BSP)
Spare MCBs
SET OF SPARES FOR 2 YEARS OF NORMAL OPERATION (EACH EQUIPMENT 1 SET)
Please Indicate the detailed list of spares with individual prices
Operation/ Service/ Spare parts manual – 2 Sets to be sent along with Machine
and 1 Set to HMTI, Bangalore.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 53 of 115
20 Nos.
1 No.
1 No.
1 No.
1 No.
1 No.
1 No.
1 No.
1 No.
1 No.
5. MIG WELDING MACHINE:
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Item : MIG WELDING MACHINE:
Ref. No: 6/21 of Annexure 6
Qty : 2 Nos
Sl. No.
Description
1
a.
b.
1.10
MIG WELDING EQUIPMENT:
MIG Welding equipment complete unit operating on 3 Phase 380V, 50Hz, AC, thyristor based
power source, remote controlled indefinitely variable current of 60 – 400A along with wire
feeder & Torch, mounted on suitable wheels for easy manourablity as per following
specifications and accessories.(all accessories of the equipment shall confirm to ISI standard or
equivalent).
Secondary short circuit protection for the power source.
Crater voltage and crater current control facility
BRIEF SPECIFICATION:
1.11
a.
b.
c.
d.
1.12
a.
b.
INPUT POWER:
Supply Voltage - 380 V
Phase / Frequency: 3 phase / 50 Hz
Input Power @ 60% Duty Cycle: 21 KVA
Input Power @ 100% Duty Cycle: 19 KVA
OUTPUT POWER:
Open Circuit Voltage – 50 V
Welding Current Range – 60 to 400 A
c.
d.
1.13
a.
b.
Max. Welding Current / load - @ 60% Duty Cycle – 400A/34 V
Max. Welding Current / load - @ 100% Duty Cycle – 310A/ 29.5 V
GENERAL:
Type of cooling – Forced air
Class of Insulation – H
c.
1.14
a.
b.
c.
d.
1.15
a.
b.
c.
d.
1.20
1.22
1.23
1.24
1.25
Type of Current & Voltage Control – Remote control unit
WIRE FEEDER:
Wire drive motor – DC Motor 18 V/ 65 W
Wire Diameter – 0.8 to 1.6 mm
Wire Feed Speed – 1.2/18 meter/minutes
Drive System – 2 Roll quick release type
TORCH:
Max. Current Capacity @60% duty cycle:
under CO2 - 400 A
under MIG - 320 A
Type of Cooling – Gas
ACCESSORIES TO BE SUPPLIED ALONG WITH EACH EQUIPMENT – EACH SET CONTAINING
FOLLOWING
Carbon di oxide gas cylinder fitted with double stage double
1 Set
gauge pressure & flow regulators mounted on a trolley
Suitable CO2 Gas hose of 5 meters length
1 No.
Welding cable and control cable of each 5 meters length
1 Set
Earthing cable and clamps of 5 meters length
1 Set
Welders cap
2 Nos.
1.26
1.27
1.28
1.29
Head shield
Black and Plain Glass one number each
Chipping hammer
Wire brush
1.21
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 54 of 115
1 No.
1 Set
1 No.
1 No.
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Item : MIG WELDING MACHINE:
Ref. No: 6/21 of Annexure 6
Qty : 2 Nos
Sl. No.
Description
1.30
1.31
1.32
1.33
1.34
1.35
1.36
1.37
1.30
1.31
1.40
Container bag
1 No.
Anti spatter spray (100 ml pack)
10 Nos.
Contact tip 1.2 mm
25 Nos.
Tip holder
5 Nos.
Liner
3 Nos.
Roller (1.2 mm)
2 Nos.
General purpose copper coated Co2 wire (15 kgs. each)
10 Rolls
Gas Preheater
1 No.
SET OF SPARES FOR 2 YEARS OF NORMAL OPERATION ( EACH EQUIPMENT 1 SET)
Please Indicate the detailed list of spares with individual prices
Operation/ Service/ Spare parts manual – 2 Sets to be sent along with Machine
1 No.
and 1 Set to HMTI, Bangalore
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 55 of 115
6. TIG WELDING EQUIPMENT:
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Item : TIG WELDING EQUIPMENT
Ref. No: 6/22 of Annexure 6
Sl. No.
1
Qty : 2 Nos
1.10
1.11
a.
b.
c.
1.12
a.
b.
c.
d.
1.13
1.14
1.15
i.
a.
b.
ii.
a.
b.
c.
Description
TIG WELDING EQUIPMENT:
TIG Welding equipment complete unit operating on 3 Phase 380V, 50Hz, AC, thyristor based
power source, with variable current of 40 – 400A along with welding control unit & Torch,
mounted on suitable wheels for easy manourablity as per following specifications and
accessories.(all accessories of the equipment shall confirm to ISI standard or equivalent.
Power source with Line voltage compensation for maintaining weld consistency, keeping output
power constant even with line voltage changes of ± 10%
Remote on/off control for the easiness of operators to turn power source on /off from a
distance.
Power source with six pulse full wave thyristor control.
Foot current control remote for TIG welding where the output current will increase when the
welder increases the pressure on the foot remote but only to the set value of the current at the
power source.
BRIEF SPECIFICATION:
INPUT POWER:
Primary Voltage: 380V
Phase / Frequency: 3 phase / 50 Hz
Input Power @ 100% Duty Cycle: 19 KVA
OUTPUT POWER:
Open Circuit Voltage: 80 V
Welding Current Range: 20 – 400 A
Max. Welding Current @ 60% Duty Cycle: 400 A
Max. Welding Current @ 100% Duty Cycle: 310 A
Class of Insulation: H
Cooling: Forced Air
TIG WELDING CONTROL UNIT:
Input:
Primary Voltage: 230 V
Phase / Frequency: 1 phase /50 Hz
Rating:
Welding Current DC
@ 60% Duty Cycle: 300 A
@ 100% Duty Cycle: 240 A
iii.
iv.
v.
a.
b.
c.
1.16
i.
a.
b.
1.17
1.18
1.19
Gas Pre-flow Time: 0.1- 5 Sec
Gas Post Flow Time: 1 – 30 Sec
General:
Water Tank Capacity : 15 Litres
Protection Class: IP23
Mode of Operation: 2 / 4 Track
TORCH:
Max current carrying capacity
@ 60% Duty Cycle: 300 DC
@ 100% Duty Cycle: 230 DC
Type Cooling: water
Electrode capacity: 1.6, 2.4, 3.2 & 4
Foot current control remote: 1 no
a.
B
c.
d.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 56 of 115
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Item : TIG WELDING EQUIPMENT
Ref. No: 6/22 of Annexure 6
Sl. No.
1.20
Qty : 2 Nos
1.22
1.33
Description
ACCESSORIES TO BE SUPPLIED ALONG WITH EACH EQUIPMENT – EACH SET CONTAINING
FOLLOWING
Argon gas cylinder fitted with double stage double
1SET
gauge pressure & flow regulators mounted on a trolley
Suitable Argon Gas hose of 5 meters length
1 No.
Earthing cable and clamps of 5 meters length
1 Set
1.34
1.35
1.36
1.37
1.38
1.39
Welders cap
Head shield
Black and Plain Glass one number each
Hand gloves and leg guard one pair each
Chipping hammer
Wire brush
1.40
1.41
1.42
1.50
1.51
1.60
Container bag
Tungsten Electrode
Continuous welding consumables 1.6 mm dia. 20 Kg box
SET OF SPARES FOR 2 YEARS OF NORMAL OPERATION ( EACH EQUIPMENT 1 SET)
Please Indicate the detailed list of spares with individual prices
Operation/ Service/ Spare parts manual – 2 Sets to be sent along with Machine
and 1 Set to HMTI, Bangalore
1.21
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 57 of 115
2 Nos.
1 No.
1 Set
1 Set
1 Set
1 No.
1 No.
1 No.
10 Nos.
1 No.
7. SUBMERGED ARC WELDING:
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Item : SUBMERGED ARC WELDING
Ref. No: 6/23 of Annexure 6
Qty : 2 Nos
Sl. No.
Description
1
1.10
SUBMERGED ARC WELDING:
Submerged Arc Welding complete unit operating on 3 Phase 380V, 50Hz, AC, diode based power
source of welding current output of 1000 A along with Welding Head , mounted on suitable
wheels for easy manourablity as per following specifications and accessories.
BRIEF SPECIFICATION:
1.11
a.
b.
c.
INPUT POWER:
Power supply: 380V
Phase / Frequency: 3 phase / 50 Hz
Rating @ 60% Duty Cycle: Min 54 KVA
1.12
a.
b.
c.
d.
e.
f.
1.13
a.
b.
OUTPUT POWER:
Welding Current (Max): 1000 A
Open Circuit Voltage Range: 24 to 52 V
Max. Welding Current @ 60% Duty Cycle: 1000 A
Max. Welding Current @ 100% Duty Cycle: 800 A
Type of Insulation: F Class
Type of Cooling: Forced Air
WELDING HEAD:
Max welding current @ 60% duty cycle: 1500 A
Max welding current @ 100% duty cycle: 1250 A
c.
d.
1.14
i.
Wire Dia: 2,2.5,3,4,5 mm
Wire Speed Range: 0.5 – 4 meters per min
Control Unit:
Input Power: 42 V / 1 phase / 50 Hz
ii.
a.
b.
c.
d.
e.
f.
g.
h.
i.
1.20
1.21
1.22
1.23
1.24
1.25
1.26
1.27
1.28
1.29
Range of Adjustment:
Vertical (Z): Min 100 mm (Motorised)
Horizontal (X): Min 100 mm (Motorised)
Horizontal (Y): Min 140 mm (Manual)
Transverse to Head Travel: 45 Degree
Parallel to Head Travel: 30 Degree
Horizontal Swing: Min 270 Degree
Standard Bore for Spool: 285 to 315 mm
Flux Hooper Capacity: 10 Kgs
Wire reel capacity: 25 Kgs.
ACCESSORIES TO BE SUPPLIED ALONG WITH EACH EQUIPMENT – EACH SET CONTAINING
FOLLOWING
Set of Welding cables and Control cable each of 5 meters
1 Set
length (90 sq mm)
Earthing cable and clamps of 5 meters length
1 Set
Welders cap
2 Nos.
Head shield
1 No.
Black and Plain Glass one number each
1 Set
Hand gloves and leg guard one pair each
1 Set
Chipping hammer
1 No.
Wire brush
1 No.
Container bag
1 No.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 58 of 115
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Item : SUBMERGED ARC WELDING
Ref. No: 6/23 of Annexure 6
Qty : 2 Nos
Sl. No.
Description
1.30
1.31
1.32
1.33
1.34
1.40
1.41
1.50
Welding consumables SAW wire of 15 kg spool
12 Nos.
Flux: 100 kgs
Wire cutter- for cutting upto 5 mm wire
1 No.
Nozzle 3 mm
15 Nos.
Roller 3 mm
2 Nos.
SET OF SPARES FOR 2 YEARS OF NORMAL OPERATION ( EACH EQUIPMENT 1 SET)
Please Indicate the detailed list of spares with individual prices
Operation/ Service/ Spare parts manual – 2 Sets to be sent along with
1 No.
Machine and 1 Set to HMTI, Bangalore
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 59 of 115
8. OXY - ACETYLENE GAS WELDING EQUIPMENT:
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Item : OXY - ACETYLENE GAS WELDING EQUIPMENT
Ref. No: 6/24 of Annexure 6
Qty : 4 Nos
Sl. No.
Description
1
1.11
OXY - ACETYLENE GAS WELDING EQUIPMENT:
Oxy – Acetylene gas welding equipment complete unit with oxygen and acetylene cylinders
mounted on a suitable trolley with handle, each cylinder fitted with double stage double gauge
pressure & flow regulators, welding & cutting gun with following specifications and accessories.
(all accessories of the equipment shall confirm to ISI standard or equivalent).
CUTTING GUN:
Standard Cutting gun 450 mm length & cutting angle 90 degree fitted with flash back arrestor
and nozzle size 3/64 inch Suitable rubber hose of 10 meter length, ID 8 mm (inside diameter)
each for oxygen and acetylene gases along with hose connectors.
WELDING GUN:
Standard welding gun for preheating and brazing of sheet metals fitted with flash back arrestor
along with preheating tips Nos. 2,3,6,13,20&30 and brazing tips Nos. 1,2,3,4,5&6. Suitable
rubber hoses of 10 meter length, ID 8 mm (inside diameter) each for oxygen and acetylene gases
along with hose connectors.
ACCESSORIES TO BE SUPPLIED ALONG WITH EACH EQUIPMENT - EACH SET CONTAINING
FOLLOWING:
Welding Hose for oxygen, ID 8 mm & length 10 Meters
1 No.
1.12
Welding Hose for Acetylene, ID 8 mm & length 10 meters
1 No.
1.13
Hose Clips
1 Set
1.14
Set of spanners
1 Set
1.15
Hose Connectors
1 Set
1.16
Double stage double gauge regulators
1 Set
2.20
SET OF SPARES FOR 2 YEARS OF NORMAL OPERATION – ( EACH EQUIPMENT 1 SET)
1.21
Please Indicate the detailed list of spares with individual prices
1.30
Operation/ Service/ Spare parts manual – 2 sets to be sent along with Machine
and 1 set to HMTI, Bangalore
1.10
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 60 of 115
1 No.
9. PORTABLE FLAME CUTTING MACHINE
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Item : PORTABLE FLAME CUTTING MACHINE
Ref. No: 6/25 of Annexure 6
Sl. No.
1
Qty : 1 No
Description
1.10
PORTABLE FLAME CUTTING MACHINE :
Oxy – Acetylene gas based portable flame cutting Machine / Equipment complete unit with
oxygen and acetylene cylinders mounted on a suitable trolley with handle, each cylinders fitted
with double stage double gauge pressure & flow regulators and portable flame cutting Machine /
Equipment with following specifications and accessories.
All accessories of the equipment shall confirm to ISI standard or equivalent
Oxygen and acetylene cylinders mounted on a suitable trolley with handle, each cylinders fitted
with double stage double gauge pressure & flow regulators – 1Set
Suitable rubber hoses of 10 meter length, ID 5 mm (inside diameter) each for oxygen and
acetylene gases along with hose connectors- 1 Set
BRIEF SPECIFICATION:
1.11
Input Power Supply: 220 V Single Phase, 50Hz AC
1.12
Cutting Capacity: 100 mm thickness of mild steel
1.13
Straight Cut: 1.8 Meters length
1.14
Circle Cutting: 150 to 1200 mm dia
1.15
Bevel Cutting: Upto 45 degree
1.16
Cutting Speed: 100 to 1000 mm/ min
1.17
Horizontal Adjustment of torch: 80 mm
1.18
Vertical Adjustment of torch: 60 mm
1.20
1.21
ACCESSORIES TO BE SUPPLIED ALONG WITH EACH EQUIPMENT- EACH SET CONTAINING
FOLLOWING:
Aluminum Track – 1.8 meters
1 Set
1.22
1.23
ANM Nozzles- 1/16”, 3/64”, 1/32” (inches)
Attachment for circle cutting
2 Sets
1 Set
1.24
Welding Hose for Oxygen, ID 5 mm and length 10 meters
1 Set
1.25
Welding Hose for Acetylene, ID 5 mm and length 10 meters
1 Set
1.26
Hose Clips
1 Set
1.27
Set of Spanners
1 Set
1.28
Hose Connectors
1 Set
1.29
Double stage double gauge regulators
1 Set
1.30
SET OF SPARES FOR 2 YEARS OF NORMALOPERATION (EACH EQUIPMENT 1 SET)
1.31
Please Indicate the detailed list of spares with individual prices
1.40
Operation/ Service/ Spare parts manual – 2 sets to be sent along with Machine
and 1 set to HMTI, Bangalore
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 61 of 115
1 No.
Enclosure – III
LOT-3 ELECTRICAL MACHINE TRAINERS:
Sl.
No
1.
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Qty
Ref.
4/1
Electrical
a. Electrical Machine Trainer with powder coated sturdy table
1
Machine
top Aluminum flat demo panel system of dimension 1150-1190
Trainer
mm x 280 – 310 mm x 940 – 1000 mm, carrying the various high
voltage components housed in panel and essential accessories
and following 300W chasis mounted machines (8 Nos.)
1) DC Integrated m/c mounted as Dynamometer & with
speed/torque sensor acts in also as prime mover / loading
machine
2) 3 phase AC integrated 300W m/c chassis mounted
3) 1 phase AC Integrated 300W motor chassis mounted
4) 1 phase AC Integrated generator & Sync.300W M
5) Universal Motor AC/DC Integrated, 300W, Chassis mounted
6) Repulsion motor chassis mounted
7) Squirrel cage 3 phase AC 300W, 2 speed chassis mounted
motor
8) 3 phase salient pole synchronous Generator
Features:
• Aesthetically prepared colour printed water resistant
poly carbonate overlays with electrical circuit schematic
drawn for easy understanding. All test points and tags
well printed in colour.
• Should have 4 mm sturdy shrouded banana patch cords
and shrouded arrangements.
• All machines are mounted on finely painted sturdy base
frame with easy machine interchangeability.
• Provision for torque measurement delivered at shaft
with
better
resolution/readability
&
Speed
measurement. Digital display for speed & torque to be
provided.
• Provision for Speed Torque characteristics and efficiency
at various loads.
• Should be able to draw all graphs.
• Facilitates easy and safe wiring by students.
The Panel to house the following components:
1.
2.
3.
4.
5.
6.
7.
Input 3 phase DOL Starter panel
Integrated AC 1 phase measurement panel
Star-Delta starter panel
3 Phase wound Rotor & Sync. Motor panel
1 phase Motor, Alternator & Sync. Motor Panel
DC voltmeter and DC ammeter panel
SCR Actuator (variable DC) cum sensor signal
conditioning panel
8. Instrumentation Power supply cum and digital display
panel
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 62 of 115
Sl.
No
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Ref.
9. Resistor Load panel
10. LC Load panel
11. Variable AC & DC supply panel
12. Energy Meter panel
Qty
b. Accessories: Should provide Patch Cord Set – 1No., Rheostat
200W – 1No., Hand held non contact Digital tachometer – 1No,
Bidirectional power meter & analyzer – 1No.
c. Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
d. Spare Parts:
Set of spare parts recommended for two years normal
operation. List of spare parts to be enclosed.
NOTE : Following documents are mandatory and are to be
submitted along with Technical Bid :
1. Front & Back Panel drawing for detailed layout of Input /
Output terminals, Power switches, Metering with schematics.
2. Circuit drawings of complete Test Rig.
1.1
2.
4/1
4/2
Work Table
for Electrical
Machine
Trainer
Industrial
Control
Trainer
Work Table:
Work Table of dimension approximately 1200 – 1250 mm (L) x
600 – 650 mm (W), 740 - 780 (H) with powder coated suitable to
mount above trainer to be supplied. Work table to be comprised
of Table Top (18mm thickness) with smooth surface finish, MS
tubular frame (16 gauge), 3 drawers and castor wheels with
locking mechanism so that the table can be easily moved.
a. Industrial Control Trainer with powder coated sturdy table
top Aluminum flat demo panel system of modular structure
carrying the various high voltage components housed in panel
and essential accessories to facilitate easy and safe wiring by
students, study of components in electrical systems and their
operations, study of Hold ON Contact Logic, study of interlocking
contact logics with trip indication , study of DOL starter logic,
study of Star-Delta logic, study of phase reversal logic, study of
Earth Leakage fault and tripping threshold & study of sequential
logic to start motors in a process plant.
Features:
• Aesthetically prepared colour printed water resistant
poly carbonate overlays with electrical circuit schematic
drawn for easy understanding. All test points and tags
well printed in colour.
• Should have 4 mm sturdy shrouded banana patch cords
and shrouded arrangements.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 63 of 115
1
1
Sl.
No
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Qty
Ref.
• All machines are mounted on finely painted sturdy base
frame with easy machine interchangeability.
• Provision for torque measurement delivered at shaft
with
better
resolution/readability
&
Speed
measurement. Digital display for speed & torque to be
provided.
• Provision for Speed Torque characteristics and efficiency
at various loads.
• Should be able to draw all graphs.
• Facilitates easy and safe wiring by students.
The Panel to house the following components:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Input 3 phase DOL Starter panel
Lamp load panel
1 phase MCB isolator panel
Contractor panel
Over Load Relay panel
Push button panel
Proximity cum Limit switch panel
DC power supply panel
Relay panel
b. Accessories: Should provide Patch Cord Set – 1No., Rheostat
200W – 1No., Hand held non contact Digital tachometer – 1No,
Bidirectional power meter & analyzer – 1No.
c. Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
d. Spare Parts:
Set of spare parts recommended for two years normal
operation. List of spare parts to be enclosed.
NOTE : Following documents are mandatory and are to be
submitted along with Technical Bid :
2.1
4/2
1. Front & Back Panel drawing for detailed layout of Input /
Output terminals, Power switches, Metering with schematics.
2. Circuit drawings of complete Test Rig.
Worktable for Work Table:
Work Table of dimension approximately 1200 – 1250 mm (L) x
Industrial
600 – 650 mm (W), 740 - 780 (H) with powder coated suitable to
Control
mount above trainer to be supplied. Work table to be comprised
Trainer
of Table Top (18mm thickness) with smooth surface finish, MS
tubular frame (16 gauge), 3 drawers and castor wheels with
locking mechanism so that the table can be easily moved.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 64 of 115
1
Sl.
No
3.
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Qty
Ref.
4/3
3 Phase AC a. 3 Phase AC Motor Fault Simulator with powder coated sturdy
1
Motor Fault table top Aluminum flat demo panel system of dimension 890 –
Simulator
920 mm(L) x 280 – 320 mm(D) x 480-520 mm(H) carrying the
various high voltage components housed in panel and essential
accessories to study the following faults:
1) Over current
2) Under current
3) High temperature
4) Single phasing
5) Reverse phasing
6) Under voltage
7) Winding open
Features:
• Aesthetically prepared colour printed water resistant
poly carbonate overlays with electrical circuit schematic
drawn for easy understanding. All test points and tags
well printed in colour.
• Should have 4 mm sturdy shrouded banana patch cords
and shrouded arrangements.
• All machines are mounted on finely painted sturdy base
frame with easy machine interchangeability.
• Provision for torque measurement delivered at shaft
with
better
resolution/readability
&
Speed
measurement. Digital display for speed & torque to be
provided.
• Provision for Speed Torque characteristics and efficiency
at various loads.
• Should be able to draw all graphs.
• Facilitates easy and safe wiring by students.
• Fault simulator to be built on the panel on top of motor
shrouded under cover for carrying out the experiments.
• Each panel has colorful screw less overlays showing
circuit diagram & its connection tag numbers for easy
understanding and connections.
The Panel to house the following components:
•
•
•
•
•
Input 3 phase DOL Starter panel
AC voltmeter panel
AC ammeter panel
Start-Delta starter panel
3 Phase sequence indicator panel
Motor:
3 Phase squirrel cage induction motor 0.5 HP, 1500 RPM, 6
terminal motor to be provided.
•
•
Star-Delta starter panel
3 Phase wound Rotor & Sync. Motor panel
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 65 of 115
Sl.
No
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Qty
Ref.
• 1 phase Motor, Alternator & Sync. Motor Panel
• DC voltmeter and DC ammeter panel
• SCR Actuator (variable DC) cum sensor signal
conditioning panel
• Instrumentation Power supply cum and digital display
panel
• Resistor Load panel
• LC Load panel
• Variable AC & DC supply panel
• Energy Meter panel
b. Accessories: Should provide Patch Cord Set – 1No., Rheostat 1No., Hand held non contact Digital tachometer – 1No,
Bidirectional power meter & analyzer – 1No.
c. Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
d. Spare Parts:
Set of spare parts recommended for two years normal
operation. List of spare parts to be enclosed.
NOTE : Following documents are mandatory and are to be
submitted along with Technical Bid :
3.1
4/3
4.
4/4
1. Front & Back Panel drawing for detailed layout of Input /
Output terminals, Power switches, Metering with schematics.
2. Circuit drawings of complete Test Rig.
Work Table Work Table:
for 3 Phase AC Work Table of dimension approximately 1200 – 1250 mm (L) x
Motor Fault 600 – 650 mm (W), 740 - 780 (H) with powder coated suitable to
Simulator
mount above trainer to be supplied. Work table to be comprised
of Table Top (18mm thickness) with smooth surface finish, MS
tubular frame (16 gauge), 3 drawers and castor wheels with
locking mechanism so that the table can be easily moved.
House Wiring a. House Wiring Installation Trainer with powder coated sturdy
Installation
table top Aluminum flat demo panel system of modular
Trainer
structure carrying the various high voltage components housed
in panel and essential accessories to facilitate easy and safe
wiring by students, study of components in electrical systems
and their operations, study of Hold ON Contact Logic, study of
interlocking contact logics with trip indication , study of DOL
starter logic, study of Star-Delta logic, study of phase reversal
logic, study of Earth Leakage fault and tripping threshold & study
of sequential logic to start motors in a process plant.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 66 of 115
1
1
Sl.
No
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Qty
Ref.
Features:
• Aesthetically prepared colour printed water resistant
poly carbonate overlays with electrical circuit schematic
drawn for easy understanding. All test points and tags
well printed in colour.
• Should have 4 mm sturdy shrouded banana patch cords
and shrouded arrangements.
• All machines are mounted on finely painted sturdy base
frame with easy machine interchangeability.
• Provision for torque measurement delivered at shaft
with
better
resolution/readability
&
Speed
measurement. Digital display for speed & torque to be
provided.
• Provision for Speed Torque characteristics and efficiency
at various loads.
• Should be able to draw all graphs.
• Facilitates easy and safe wiring by students.
The Panel to house the following components:
10.
11.
12.
13.
14.
15.
16.
17.
18.
Input 3 phase DOL Starter panel
Lamp load panel
1 phase MCB isolator panel
Contractor panel
Over Load Relay panel
Push button panel
Proximity cum Limit switch panel
DC power supply panel
Relay panel
b. Accessories: Should provide Patch Cord Set – 1No., Rheostat
200W – 1No., Hand held non contact Digital tachometer – 1No,
Bidirectional power meter & analyzer – 1No.
c. Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
e. Spare Parts:
Set of spare parts recommended for two years normal
operation. List of spare parts to be enclosed.
NOTE : Following documents are mandatory and are to be
submitted along with Technical Bid :
1. Front & Back Panel drawing for detailed layout of Input /
Output terminals, Power switches, Metering with schematics.
2. Circuit drawings of complete Test Rig.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 67 of 115
Sl.
No
4.1
5
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Qty
Ref.
4/4
Work Table Work Table:
1
for
House Work Table of dimension approximately 1200 – 1250 mm (L) x
600 – 650 mm (W), 740 - 780 (H) with powder coated suitable to
Wiring
mount above trainer to be supplied. Work table to be comprised
Installation
of Table Top (18mm thickness) with smooth surface finish, MS
Trainer
tubular frame (16 gauge), 3 drawers and castor wheels with
locking mechanism so that the table can be easily moved.
4/5
Electrical
1
a. Electrical Control Trainer of dimension 450-480 mm(W) x 150
Control
– 170 mm(H) x 330 – 360 mm(D) containing Analog PID & with
Trainer
PC based PID controller with PID Software, Computer Interface
Adapter & USB IO module.
Features:
• Aesthetically prepared colour printed water resistant
poly carbonate overlays with electrical circuit schematic
drawn for easy understanding. All test points and tags
well printed in colour.
• Should have 4 mm sturdy shrouded banana patch cords
and shrouded arrangements.
• Provision for torque measurement delivered at shaft
with
better
resolution/readability
&
Speed
measurement. Digital display for speed & torque to be
provided.
• Provision for Speed Torque characteristics and efficiency
at various loads.
• Should be able to draw all graphs.
• Facilitates easy and safe wiring by students.
• Study of Analog PID and Digital PID.
• Facility to monitor behavior of the PID output & process
variable either on PC screen or on CRO.
• PC based PID controller with P,PI,PID control.
• To different processes using simulated building blocks as
well as real life processes using replaceable experiment
panels.
• Graph printing facility.
• Top board should contain Builtin Power supply and
Digital display unit.
• Operating voltage: 220-240 V +10%
Analog PID Controller:
•
•
•
Controller Selection: P,PI, PD, PID with slide switch
Built in Function Generator (Sine, triangular & square)
Test points for Process Error, Set Point, Measured Value,
Controller output.
PC based PID Controller:
•
•
PID software in CD form should be capable of installing
on XP, WIN7 or latest windows OS systems.
PID controller mode with parameters like Integral Time,
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 68 of 115
Sl.
No
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Qty
Ref.
Derivative Time, Derivative Gain Kd etc.
• Computer Interface Adapter to be provided to prevent
damage to PC parallel port due to wrong connections.
• USB IO module to be interface Computer Interface
adapter to USB PC port to be provided.
The following process setups (table top) to be provided for
performing experiments :
•
•
•
AC Servo Motor with synchro Control transformer and
servo pot – 1No.
Magnetic amplifier units – 2 Nos.
Potentiometric error detection cum Magnetic Amplifier
– 1No.
b. Accessories: Required number of patch cords and other
necessary accessories to be provided.
c. Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
d. Spare Parts:
Set of spare parts recommended for two years normal
operation. List of spare parts to be enclosed.
NOTE : Following documents are mandatory and are to be
submitted along with Technical Bid :
5.1
4/5
6
4/6
1. Front & Back Panel drawing for detailed layout of Input /
Output terminals, Power switches, Metering with schematics.
2. Circuit drawings of complete Test Rig.
Work Table Work Table:
for Electrical Work Table of dimension approximately 1200 – 1250 mm (L) x
600 – 650 mm (W), 740 - 780 (H) with powder coated suitable to
Control
mount above trainer to be supplied. Work table to be comprised
Trainer
of Table Top (18mm thickness) with smooth surface finish, MS
tubular frame (16 gauge), 3 drawers and castor wheels with
locking mechanism so that the table can be easily moved.
Power
Electronics
Trainer
a. Power Electronics Trainer containing a Master unit carrying
useful experiment resources like Built in Power supplies, RLC
loads, Battery charging supply etc. while the central slot will hold
replaceable experiment panels. Each multi experiment panel is
secured in an suitable molded plastic sturdy enclosure and has
colorful screw less overlay showing circuit & Connection through
Sturdy Banana Sockets & Patch Chords.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 69 of 115
1
1
Sl.
No
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Ref.
DC Supply: 12 – 15V
AC Supply: 230 V
Features:
• Aesthetically prepared colour printed water resistant
poly carbonate overlays with electrical circuit schematic
drawn for easy understanding. All test points and tags
well printed in colour.
• Should have 4 mm sturdy shrouded banana patch cords
and shrouded arrangements.
• Provision for torque measurement delivered at shaft
with
better
resolution/readability
&
Speed
measurement. Digital display for speed & torque to be
provided.
• Provision for Speed Torque characteristics and efficiency
at various loads.
• Should be able to draw all graphs.
• Facilitates easy and safe wiring by students.
The following panels to be provided for performing experiments
:
Converter / Inverter Panel:
•
•
•
•
•
•
•
•
Half Wave & Full Wave Fully Controlled converter
SCR Controlled Converter 1 phase with R-L Load
Study of SCR converter (Open Loop) output with
Inductance
Input and Capacitance Input filters
Effect of Source Impedance on performance of SCR
converters.
Study of closed loop SCR converters with Resistive Load.
Study of closed loop SCR converters with Motor Load
Study of full wave -half controlled SCR bridge.
Triggering circuit / dv/dt Protection panel:
•
•
•
•
•
•
Study of SCR dv/dt protection using gate termination.
Study of SCR dv/dt protection using gate reverse bias
with resistance.
Study of SCR dv/dt protection using gate reverse bias
with resistance and diode.
Study of SCR dv/dt protection using polarised snubber.
Study of SCR dv/dt protection using polarised RC
snubber with discharge resistor.
Study of Triac dv/dt protection using RC Snubber.
IGBT / MOSFET Inverter Panel: To study switching characteristics
of MOSFET / IGBT.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 70 of 115
Qty
Sl.
No
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Qty
Ref.
b. Accessories:
• Required number of patch cords to be provided.
• Power Scope attachment CRO for off ground differential
measurements upto 1000Vdc to facilitate checking
inverter/converter waveform – 1 No.
• Foot mounting Permanent Magnet DC motor (PMDC)
(200W/2000RPM) with Tachogenerator and brake pully
arrangement loading arrangement using spring
balances– 1No.
c. Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
d. Spare Parts:
Set of spare parts recommended for two years normal
operation. List of spare parts to be enclosed.
NOTE : Following documents are mandatory and are to be
submitted along with Technical Bid :
6.1
4/6
7
4/7
1. Front & Back Panel drawing for detailed layout of Input /
Output terminals, Power switches, Metering with schematics.
2. Circuit drawings of complete Test Rig.
Work Table Work Table:
for
Power Work Table of dimension approximately 1200 – 1250 mm (L) x
600 – 650 mm (W), 740 - 780 (H) with powder coated suitable to
Electronics
mount above trainer to be supplied. Work table to be comprised
Trainer
of Table Top (18mm thickness) with smooth surface finish, MS
tubular frame (16 gauge), 3 drawers and castor wheels with
locking mechanism so that the table can be easily moved.
Applied
a. Applied Power Electronics Trainer to with powder coated
Power
sturdy table top Aluminum flat demo panel system of
Electronics
dimension 940 – 1000 mm(L) x 280 – 320 mm(D) x 520-560
Trainer
mm(H) to study Open loop torque speed characteristics and
Closed loop speed control using Armature voltage / speed feed
back and consists of
•
•
•
DC Motor Thyristorised speed control trainer with
200V/200W chasis mounted PMDC motor with
electrical
tachogenerator
and
brake
pully
arrangement – 1No.
3 Phase HV thyristor Control trainer – 1No.
UPS Trainer to study and working of offline UPS -1 No.
Features:
• Aesthetically prepared colour printed water resistant
poly carbonate overlays with electrical circuit schematic
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 71 of 115
1
1 Set
Sl.
No
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Qty
Ref.
drawn for easy understanding. All test points and tags
well printed in colour.
• Should have 4 mm sturdy shrouded banana patch cords
and shrouded arrangements.
• All machines are mounted on finely painted sturdy base
frame with easy machine interchangeability.
• Provision for torque measurement delivered at shaft
with
better
resolution/readability
&
Speed
measurement. Digital display for speed & torque to be
provided.
• Provision for Speed Torque characteristics and efficiency
at various loads.
• Should be able to draw all graphs.
• Facilitates easy and safe wiring by students.
b. Accessories:
Required number of patch cords and other necessary accessories
to be provided.
c. Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
d. Spare Parts:
Set of spare parts recommended for two years normal
operation. List of spare parts to be enclosed.
NOTE : Following documents are mandatory and are to be
submitted along with Technical Bid :
1. Front & Back Panel drawing for detailed layout of Input /
Output terminals, Power switches, Metering with schematics.
2. Circuit drawings of complete Test Rig.
7.1
8
4/7
4/8
Work Table
for Applied
Power
Electronics
Trainer
Work Table:
Electrical
Trainer
a. Electrical Transformer Trainer with Flat demo panel systems
of dimension 950 – 970 (L) x 280 – 320 (W) x 700 – 740 (H)
containing 1 Phase 300VA (2Nos.) and 3 Phase 300 VA(1No.)
Transformer Trainers.
1
Work Table of dimension approximately 1200 – 1250 mm (L) x
600 – 650 mm (W), 740 - 780 (H) with powder coated suitable to
mount above trainer to be supplied. Work table to be comprised
of Table Top (18mm thickness) with smooth surface finish, MS
tubular frame (16 gauge), 3 drawers and castor wheels with
locking mechanism so that the table can be easily moved.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 72 of 115
1
Sl.
No
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Ref.
Single Phase:
Primary: 0 -230 V
Secondary: 200 V
Three Phase:
Primary: 0 -415 V
Secondary: 220 V
Features:
• Aesthetically prepared colour printed water resistant
poly carbonate overlays with electrical circuit schematic
drawn for easy understanding. All test points and tags
well printed in colour.
• Should have 4 mm sturdy shrouded banana patch cords
and shrouded arrangements.
• All machines are mounted on finely painted sturdy base
frame with easy machine interchangeability.
• Provision for torque measurement delivered at shaft
with
better
resolution/readability
&
Speed
measurement. Digital display for speed & torque to be
provided.
• Provision for Speed Torque characteristics and efficiency
at various loads.
• Should be able to draw all graphs.
• Facilitates easy and safe wiring by students.
• Study of Transformer regulation.
• Measurement of winding temperature.
• Effect of type of load on transformer output waveform.
• Study of Three phase transformer connections.
The Panel to house the following components:
•
•
•
•
•
•
•
Input 3 phase DOL Starter panel
AC Primary & Secondary voltmeter panel.
Resistive load panel
Dimmer panel
1 phase Transformer Panel
3 phase Transformer Panel
MCB isolator panel
b. Accessories: Required number of patch cords , suitable
wattmeter – 1No and other necessary accessories to be
provided.
c. Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 73 of 115
Qty
Sl.
No
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Ref.
supported with observator tables for easy learning.
Qty
d. Spare Parts:
Set of spare parts recommended for two years normal
operation. List of spare parts to be enclosed.
NOTE : Following documents are mandatory and are to be
submitted along with Technical Bid :
8.1
4/8
9
4/9
1. Front & Back Panel drawing for detailed layout of Input /
Output terminals, Power switches, Metering with schematics.
2. Circuit drawings of complete Test Rig.
Work Table Work Table:
for Electrical Work Table of dimension approximately 1200 – 1250 mm (L) x
600 – 650 mm (W), 740 - 780 (H) with powder coated suitable to
Trainer
mount above trainer to be supplied. Work table to be comprised
of Table Top (18mm thickness) with smooth surface finish, MS
tubular frame (16 gauge), 3 drawers and castor wheels with
locking mechanism so that the table can be easily moved.
3-Phase
a. 3-Phase Induction Motor Speed Control Trainer with powder
Induction
coated sturdy table top Aluminum flat demo panel system of
Motor Speed dimension 940-1000 mm(L) x 280 – 320 mm(W) x 520 – 560
Control
mm(H) containing 0.5 HP squirrel cage induction motor foot
Trainer
mounted on chasis with brake pulley and Hand Held tacho
meter.
Features:
•
•
•
•
•
•
•
Aesthetically prepared colour printed water resistant
poly carbonate overlays with electrical circuit schematic
drawn for easy understanding. All test points and tags
well printed in colour.
Should have 4 mm sturdy shrouded banana patch cords
and shrouded arrangements.
All machines are mounted on finely painted sturdy base
frame with easy machine interchangeability.
Provision for torque measurement delivered at shaft
with
better
resolution/readability
&
Speed
measurement. Digital display for speed & torque to be
provided.
Provision for Speed Torque characteristics and efficiency
at various loads.
Should be able to draw all graphs.
Facilitates easy and safe wiring by students.
The Panel to house the following components:
•
•
•
•
1 phase motor, alternator panel
AC voltmeter panel
AC ammeter panel
IGBT controlled AC drive panel
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 74 of 115
1
1
Sl.
No
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Ref.
Qty
b. Accessories: Required number of patch cords and other
necessary accessories to be provided.
c. Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
d. Spare Parts:
Set of spare parts recommended for two years normal
operation. List of spare parts to be enclosed.
NOTE : Following documents are mandatory and are to be
submitted along with Technical Bid :
9.1
4/9
Work Table
for
3-Phase
Induction
Motor Speed
Control
Trainer
10
4/10
3-Phase
Induction
Motor Fault
Simulator
1. Front & Back Panel drawing for detailed layout of Input /
Output terminals, Power switches, Metering with schematics.
2. Circuit drawings of complete Test Rig.
Work Table:
Work Table of dimension approximately 1200 – 1250 mm (L) x
600 – 650 mm (W), 740 - 780 (H) with powder coated suitable to
mount above trainer to be supplied. Work table to be comprised
of Table Top (18mm thickness) with smooth surface finish, MS
tubular frame (16 gauge), 3 drawers and castor wheels with
locking mechanism so that the table can be easily moved.
a. 3-Phase Induction Motor Fault Simulator with powder coated
sturdy table top Aluminum flat demo panel system of dimension
900-950 mm(L) x 280 – 320 mm(D) x 450 – 520 mm(H)
containing 0.5 HP squirrel cage induction motor foot mounted
on chasis with brake pulley and Hand Held tacho meter.
Features:
• Aesthetically prepared colour printed water resistant
poly carbonate overlays with electrical circuit schematic
drawn for easy understanding. All test points and tags
well printed in colour.
• Should have 4 mm sturdy shrouded banana patch cords
and shrouded arrangements.
• All machines are mounted on finely painted sturdy base
frame with easy machine interchangeability.
• Provision for torque measurement delivered at shaft
with
better
resolution/readability
&
Speed
measurement. Digital display for speed & torque to be
provided.
• Provision for Speed Torque characteristics and efficiency
at various loads.
• Should be able to draw all graphs.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 75 of 115
1
1
Sl.
No
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Ref.
• Facilitates easy and safe wiring by students.
Qty
The Panel to house the following components:
•
•
•
•
Input 3 phase DOL starter panel
AC voltmeter panel
AC ammeter panel
Star delta starter panel
b. Accessories: Required number of patch cords and other
necessary accessories to be provided.
c. Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
d. Spare Parts:
Set of spare parts recommended for two years normal
operation. List of spare parts to be enclosed.
NOTE : Following documents are mandatory and are to be
submitted along with Technical Bid :
10.1 4/10
Work Table
for
3-Phase
Induction
Motor Fault
Simulator
11
Motor
Generator (AC
to DC) set
4/11
1. Front & Back Panel drawing for detailed layout of Input /
Output terminals, Power switches, Metering with schematics.
2. Circuit drawings of complete Test Rig.
Work Table:
Work Table of dimension approximately 1200 – 1250 mm (L) x
600 – 650 mm (W), 740 - 780 (H) with powder coated suitable to
mount above trainer to be supplied. Work table to be comprised
of Table Top (18mm thickness) with smooth surface finish, MS
tubular frame (16 gauge), 3 drawers and castor wheels with
locking mechanism so that the table can be easily moved.
a. Motor Generator (AC to DC) set with powder coated sturdy
table top Aluminum flat demo panel system of dimension 11501200 mm(L) x 280 – 320 mm(D) x 970 – 1000 mm(H) containing
3 Phase 3HP, 400V, 1500 RPM Induction Motor is coupled to a
DC Shunt Generator to study Speed torque curve of Shunt
motor, DC series motor, DC compound motor and V-I efficiency
curve of DC shunt generator, DC series generator, DC compound
generator.
Features:
• Aesthetically prepared colour printed water resistant
poly carbonate overlays with electrical circuit schematic
drawn for easy understanding. All test points and tags
well printed in colour.
• Should have 4 mm sturdy shrouded banana patch cords
and shrouded arrangements.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 76 of 115
1
1
Sl.
No
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Ref.
•
•
•
•
•
Qty
All machines are mounted on finely painted sturdy base
frame with easy machine interchangeability.
Provision for torque measurement delivered at shaft
with
better
resolution/readability
&
Speed
measurement. Digital display for speed & torque to be
provided.
Provision for Speed Torque characteristics and efficiency
at various loads.
Should be able to draw all graphs.
Facilitates easy and safe wiring by students.
The Panel to house the following components:
•
•
•
•
•
•
•
DOL starter panel
Star delta starter panel
Energy meter panel
DC voltmeter panel
DC ammeter panel
Resistor load panel
Variable AC/DC power supply panel
b. Accessories: Required number of patch cords and other
necessary accessories to be provided.
c. Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
d. Spare Parts:
Set of spare parts recommended for two years normal
operation. List of spare parts to be enclosed.
NOTE : Following documents are mandatory and are to be
submitted along with Technical Bid :
1. Front & Back Panel drawing for detailed layout of Input /
Output terminals, Power switches, Metering with schematics.
2. Circuit drawings of complete Test Rig.
11.1 4/11
Work Table
for
Motor
Generator (AC
to DC) set
Work Table:
Work Table of dimension approximately 1200 – 1250 mm (L) x
600 – 650 mm (W), 740 - 780 (H) with powder coated suitable to
mount above trainer to be supplied. Work table to be comprised
of Table Top (18mm thickness) with smooth surface finish, MS
tubular frame (16 gauge), 3 drawers and castor wheels with
locking mechanism so that the table can be easily moved.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 77 of 115
1
Sl.
No
12
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Qty
Ref.
4/12
Motor
a. Motor Generator (DC to AC) set with powder coated sturdy
1
Generator
table top Aluminum flat demo panel system of dimension 1150(DC to AC) set 1200 mm(L) x 280 – 320 mm(D) x 970 – 1000 mm(H) containing
3hp 230V 1500 RPM DC Shunt motor coupled to 2KVA
Alternator.
Features:
• Aesthetically prepared colour printed water resistant
poly carbonate overlays with electrical circuit schematic
drawn for easy understanding. All test points and tags
well printed in colour.
• Should have 4 mm sturdy shrouded banana patch cords
and shrouded arrangements.
• All machines are mounted on finely painted sturdy base
frame with easy machine interchangeability.
• Provision for torque measurement delivered at shaft
with
better
resolution/readability
&
Speed
measurement. Digital display for speed & torque to be
provided.
• Provision for Speed Torque characteristics and efficiency
at various loads.
• Should be able to draw all graphs.
• Facilitates easy and safe wiring by students.
The Panel to house the following components:
•
•
•
•
•
•
•
DOL starter panel
Star delta starter panel
Energy meter panel
DC voltmeter panel
DC ammeter panel
Resistor load panel
Variable AC/DC power supply panel
b. Accessories: Required number of patch cords and other
necessary accessories to be provided.
c. Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
d. Spare Parts:
Set of spare parts recommended for two years normal
operation. List of spare parts to be enclosed.
NOTE : Following documents are mandatory and are to be
submitted along with Technical Bid :
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 78 of 115
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Qty
Ref.
1. Front & Back Panel drawing for detailed layout of Input /
Output terminals, Power switches, Metering with schematics.
2. Circuit drawings of complete Test Rig.
12.1 4/12
Work Table Work Table:
1
for
Motor Work Table of dimension approximately 1200 – 1250 mm (L) x
600 – 650 mm (W), 740 - 780 (H) with powder coated suitable to
Generator
(DC to AC) set mount above trainer to be supplied. Work table to be comprised
of Table Top (18mm thickness) with smooth surface finish, MS
tubular frame (16 gauge), 3 drawers and castor wheels with
locking mechanism so that the table can be easily moved.
13
4/13
DC Generators a. DC Generator trainer with powder coated sturdy table top
1
Aluminum flat demo panel system of dimension 1150-1200
mm(L) x 280 – 320 mm(D) x 970 – 1000 mm(H) containing 1 DC
Shunt Generator set 1KW 230V 1500RPM and 1 DC Compound
Generator set 1KW 230V 1500RPM to study Speed torque and
efficiency of Shunt motor, DC series motor, DC compound
motor.
Sl.
No
Features:
• Aesthetically prepared colour printed water resistant
poly carbonate overlays with electrical circuit schematic
drawn for easy understanding. All test points and tags
well printed in colour.
• Should have 4 mm sturdy shrouded banana patch cords
and shrouded arrangements.
• All machines are mounted on finely painted sturdy base
frame with easy machine interchangeability.
• Provision for torque measurement delivered at shaft
with
better
resolution/readability
&
Speed
measurement. Digital display for speed & torque to be
provided.
• Provision for Speed Torque characteristics and efficiency
at various loads.
• Should be able to draw all graphs.
• Facilitates easy and safe wiring by students.
The Panel to house the following components:
•
•
•
DC voltmeter panel
DC ammeter panel
Power supply panel
b. Accessories: Required number of patch cords and other
necessary accessories to be provided.
c. Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 79 of 115
Sl.
No
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Ref.
Qty
d. Spare Parts:
Set of spare parts recommended for two years normal
operation. List of spare parts to be enclosed.
NOTE : Following documents are mandatory and are to be
submitted along with Technical Bid :
13.1 4/13
14
Work Table
for
DC
Generators
4/15,
Motor Series
4/16 & DC , Motor
4/17
Shunt
DC
&Motor
Compound
Wound DC
1. Front & Back Panel drawing for detailed layout of Input /
Output terminals, Power switches, Metering with schematics.
2. Circuit drawings of complete Test Rig.
Work Table:
Work Table of dimension approximately 1200 – 1250 mm (L) x
600 – 650 mm (W), 740 - 780 (H) with powder coated suitable to
mount above trainer to be supplied. Work table to be comprised
of Table Top (18mm thickness) with smooth surface finish, MS
tubular frame (16 gauge), 3 drawers and castor wheels with
locking mechanism so that the table can be easily moved.
a. DC Series, DC Shunt Motor & DC Compound wound Motor
trainer with powder coated sturdy table top Aluminum flat
demo panel system of dimension 940 – 1000 mm(L) x 280 320mm x 530 – 570 mm(H) containing the following motors to
study open loop torque speed characteristics and closed loop
speed control.
• 1 No. DC series motor 230V, 2 HP
(1.5 KW) with
mechanical brake loading system
• 1 No. DC Shunt motor 230V, 3 HP (2.2KW) with
mechanical brake loading system
• 1 No. DC compound wound, 230V, 2 HP ( 1.5 KW) with
mechanical brake loading system
Features:
• Aesthetically prepared colour printed water resistant
poly carbonate overlays with electrical circuit schematic
drawn for easy understanding. All test points and tags
well printed in colour.
• Should have 4 mm sturdy shrouded banana patch cords
and shrouded arrangements.
• All machines are mounted on finely painted sturdy base
frame with easy machine interchangeability.
• Provision for torque measurement delivered at shaft
with
better
resolution/readability
&
Speed
measurement. Digital display for speed & torque to be
provided.
• Provision for Speed Torque characteristics and efficiency
at various loads.
• Should be able to draw all graphs.
• Facilitates easy and safe wiring by students.
The Panel to house the following components:
•
DC voltmeter panel
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 80 of 115
1
1
Sl.
No
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Ref.
• DC ammeter panel
• Power supply panel
Qty
b. Accessories: Required number of patch cords and other
necessary accessories to be provided.
c. Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
d. Spare Parts:
Set of spare parts recommended for two years normal
operation. List of spare parts to be enclosed.
NOTE : Following documents are mandatory and are to be
submitted along with Technical Bid :
14.1 4/15,
Work Table
4/16 & for
Motor
4/17
Series DC ,
Motor Shunt
DC
&Motor
Compound
Wound DC
15
4/18
Motor
Squirrel-cage
AC
1. Front & Back Panel drawing for detailed layout of Input /
Output terminals, Power switches, Metering with schematics.
2. Circuit drawings of complete Test Rig.
Work Table:
Work Table of dimension approximately 1200 – 1250 mm (L) x
600 – 650 mm (W), 740 - 780 (H) with powder coated suitable to
mount above trainer to be supplied. Work table to be comprised
of Table Top (18mm thickness) with smooth surface finish, MS
tubular frame (16 gauge), 3 drawers and castor wheels with
locking mechanism so that the table can be easily moved.
a. AC 3 Ph Squirrel-cage Induction Motor with powder coated
sturdy table top Aluminum flat demo panel system of dimension
940 – 1000 mm(L) x 280 - 320mm x 530 – 570 mm(H) containing
3 phase, 400V, 50 Hz, 3 HP with mechanical brake loading system
to study Speed torque curves and efficiency of squirrel cage
rotor induction motor.
Features:
• Aesthetically prepared colour printed water resistant
poly carbonate overlays with electrical circuit schematic
drawn for easy understanding. All test points and tags
well printed in colour.
• Should have 4 mm sturdy shrouded banana patch cords
and shrouded arrangements.
• All machines are mounted on finely painted sturdy base
frame with easy machine interchangeability.
• Provision for torque measurement delivered at shaft
with
better
resolution/readability
&
Speed
measurement. Digital display for speed & torque to be
provided.
• Provision for Speed Torque characteristics and efficiency
at various loads.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 81 of 115
1
1
Sl.
No
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Ref.
• Should be able to draw all graphs.
• Facilitates easy and safe wiring by students.
Qty
The Panel to house the following components:
•
•
•
Motor panel
DC voltmeter panel
DC ammeter panel
b. Accessories: Required number of patch cords and other
necessary accessories to be provided.
c. Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
d. Spare Parts:
Set of spare parts recommended for two years normal
operation. List of spare parts to be enclosed.
NOTE : Following documents are mandatory and are to be
submitted along with Technical Bid :
1. Front & Back Panel drawing for detailed layout of Input /
Output terminals, Power switches, Metering with schematics.
2.Circuit drawings of complete Test Rig.
15.1 4/18
Work Table Work Table:
for
Motor
Squirrel-cage
Work Table of dimension approximately 1200 – 1250 mm (L) x
AC
600 – 650 mm (W), 740 - 780 (H) with powder coated suitable to
mount above trainer to be supplied. Work table to be comprised
of Table Top (18mm thickness) with smooth surface finish, MS
tubular frame (16 gauge), 3 drawers and castor wheels with
locking mechanism so that the table can be easily moved.
1
16
Motor wound a. AC 3 Ph Wound rotor (Slip ring) Motor with powder coated
slip ring AC
sturdy table top Aluminum flat demo panel system of dimension
940 – 1000 mm(L) x 280 - 320mm x 530 – 570 mm(H) containing
AC phase wound slip ring type 3phase, 400V, 3 HP with
mechanical brake loading system to study Speed torque curves
and efficiency of AC 3 Phase Slip ring motor.
1
4/19
Features:
• Aesthetically prepared colour printed water resistant
poly carbonate overlays with electrical circuit schematic
drawn for easy understanding. All test points and tags
well printed in colour.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 82 of 115
Sl.
No
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Qty
Ref.
• Should have 4 mm sturdy shrouded banana patch cords
and shrouded arrangements.
• All machines are mounted on finely painted sturdy base
frame with easy machine interchangeability.
• Provision for torque measurement delivered at shaft
with
better
resolution/readability
&
Speed
measurement. Digital display for speed & torque to be
provided.
• Provision for Speed Torque characteristics and efficiency
at various loads.
• Should be able to draw all graphs.
• Facilitates easy and safe wiring by students.
The Panel to house the following components:
•
•
•
•
•
3 phase DOL starter panel
Switch panel
DC voltmeter panel
DC ammeter panel
Power supply panel
b. Accessories: Required number of patch cords and other
necessary accessories to be provided.
c. Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
d. Spare Parts:
Set of spare parts recommended for two years normal
operation. List of spare parts to be enclosed.
NOTE : Following documents are mandatory and are to be
submitted along with Technical Bid :
16.1 4/19
1. Front & Back Panel drawing for detailed layout of Input /
Output terminals, Power switches, Metering with schematics.
3.
Circuit drawings of complete Test Rig.
4.
Work Table Work Table:
for
Motor
wound
slip Work Table of dimension approximately 1200 – 1250 mm (L) x
ring AC
600 – 650 mm (W), 740 - 780 (H) with powder coated suitable to
mount above trainer to be supplied. Work table to be comprised
of Table Top (18mm thickness) with smooth surface finish, MS
tubular frame (16 gauge), 3 drawers and castor wheels with
locking mechanism so that the table can be easily moved.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 83 of 115
1
Sl.
No
17
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Qty
Ref.
4/20 & Motor Series
1
4/21
AC
&Motor a. AC Series Motor and AC 1 Ph Capacitor start – Capacitor run
Capacitor AC
Motor trainer with powder coated sturdy table top Aluminum
flat demo panel system of dimension 940 – 1000 mm(L) x 280 320mm x 530 – 570 mm(H) containing the following Motors to
study Speed torque curves of AC Series & Capacitor motors.
•
•
1 No. 0.25 to 0.5 HP AC Single Phase Motor 230V, 50Hz
with mechanical brake loading system
1 No. AC single phase 230V, 50Hz, 1 HP capacitor type
motor with mechanical brake loading system
Features:
• Aesthetically prepared colour printed water resistant
poly carbonate overlays with electrical circuit schematic
drawn for easy understanding. All test points and tags
well printed in colour.
• Should have 4 mm sturdy shrouded banana patch cords
and shrouded arrangements.
• All machines are mounted on finely painted sturdy base
frame with easy machine interchangeability.
• Provision for torque measurement delivered at shaft
with
better
resolution/readability
&
Speed
measurement. Digital display for speed & torque to be
provided.
• Provision for Speed Torque characteristics and efficiency
at various loads.
• Should be able to draw all graphs.
• Facilitates easy and safe wiring by students.
The Panel to house the following components:
•
•
•
Motor panel
DC voltmeter panel
DC ammeter panel
b. Accessories: Required number of patch cords and other
necessary accessories to be provided.
c. Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
d. Spare Parts:
Set of spare parts recommended for two years normal
operation. List of spare parts to be enclosed.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 84 of 115
Sl.
No
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Qty
Ref.
NOTE : Following documents are mandatory and are to be
submitted along with Technical Bid :
1. Front & Back Panel drawing for detailed layout of Input /
Output terminals, Power switches, Metering with schematics.
2. Circuit drawings of complete Test Rig.
17.1 4/20 & Work Table Work Table:
4/21
for
Motor Work Table of dimension approximately 1200 – 1250 mm (L) x
Series AC & 600 – 650 mm (W), 740 - 780 (H) with powder coated suitable to
Motor
mount above trainer to be supplied. Work table to be comprised
Capacitor AC
of Table Top (18mm thickness) with smooth surface finish, MS
tubular frame (16 gauge), 3 drawers and castor wheels with
locking mechanism so that the table can be easily moved.
18
4/22
Motor
Universal AC
a. AC Universal Motor with powder coated sturdy table top
Aluminum flat demo panel system of dimension 940-1000 mm(L)
x 280 – 320 mm(W) x 520 – 570 mm(H) containing 0.25 to 0.5
HP AC Single Phase Universal Motor, 230V, 50Hz with
mechanical brake loading system to study characteristics of AC
Universal motor.
Features:
• Aesthetically prepared colour printed water resistant
poly carbonate overlays with electrical circuit schematic
drawn for easy understanding. All test points and tags
well printed in colour.
• Should have 4 mm sturdy shrouded banana patch cords
and shrouded arrangements.
• All machines are mounted on finely painted sturdy base
frame with easy machine interchangeability.
• Provision for torque measurement delivered at shaft
with
better
resolution/readability
&
Speed
measurement. Digital display for speed & torque to be
provided.
• Provision for Speed Torque characteristics and efficiency
at various loads.
• Should be able to draw all graphs.
• Facilitates easy and safe wiring by students.
The Panel to house the following components:
•
•
•
AC voltmeter panel
AC ammeter panel
Power supply panel
b. Accessories: Required number of patch cords and other
necessary accessories to be provided.
c. Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 85 of 115
1
1
Sl.
No
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Qty
Ref.
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
d. Spare Parts:
Set of spare parts recommended for two years normal
operation. List of spare parts to be enclosed.
NOTE : Following documents are mandatory and are to be
submitted along with Technical Bid :
18.1 4/22
19
4/23
1. Front & Back Panel drawing for detailed layout of Input /
Output terminals, Power switches, Metering with schematics.
2. Circuit drawings of complete Test Rig.
Work Table Work Table:
for
Motor Work Table of dimension approximately 1200 – 1250 mm (L) x
600 – 650 mm (W), 740 - 780 (H) with powder coated suitable to
Universal AC
mount above trainer to be supplied. Work table to be comprised
of Table Top (18mm thickness) with smooth surface finish, MS
tubular frame (16 gauge), 3 drawers and castor wheels with
locking mechanism so that the table can be easily moved.
Stepper motor a. Stepper Motor Trainer of dimension 450-480 mm(W) x 150 –
170 mm(H) x 330 – 360 mm(D) with Stepper motor
demonstration panel with computer based digital controller to
study the speed, director and operation of Stepper motor,
Position control by step and continuous operation.
Features:
• Aesthetically prepared colour printed water resistant
poly carbonate overlays with electrical circuit schematic
drawn for easy understanding. All test points and tags
well printed in colour.
• Should have 4 mm sturdy shrouded banana patch cords
and shrouded arrangements.
• Provision for torque measurement delivered at shaft
with
better
resolution/readability
&
Speed
measurement. Digital display for speed & torque to be
provided.
• Provision for Speed Torque characteristics and efficiency
at various loads.
• Should be able to draw all graphs.
• Facilitates easy and safe wiring by students.
• PC based Digital controller.
b. Accessories: Required number of patch cords and other
necessary accessories to be provided.
c. Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 86 of 115
1
1
Sl.
No
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Ref.
supported with observator tables for easy learning.
Qty
d. Spare Parts:
Set of spare parts recommended for two years normal
operation. List of spare parts to be enclosed.
NOTE : Following documents are mandatory and are to be
submitted along with Technical Bid :
19.1 4/23
20
4/42
1. Front & Back Panel drawing for detailed layout of Input /
Output terminals, Power switches, Metering with schematics.
2. Circuit drawings of complete Test Rig.
Work Table Work Table:
for
Stepper Work Table of dimension approximately 1200 – 1250 mm (L) x
600 – 650 mm (W), 740 - 780 (H) with powder coated suitable to
motor
mount above trainer to be supplied. Work table to be comprised
of Table Top (18mm thickness) with smooth surface finish, MS
tubular frame (16 gauge), 3 drawers and castor wheels with
locking mechanism so that the table can be easily moved.
Thyristor
/ a. Thyristor / IGBT controlled DC trainer with powder coated
IGBT
sturdy table top Aluminum flat demo panel system of dimension
controlled DC 940 – 1000 mm(L) x 280 - 320mm (W) x 530 – 570 mm(H)
trainer
containing Motor Drive 1HP Shunt type.
Features:
• Aesthetically prepared colour printed water resistant
poly carbonate overlays with electrical circuit schematic
drawn for easy understanding. All test points and tags
well printed in colour.
• Should have 4 mm sturdy shrouded banana patch cords
and shrouded arrangements.
• All machines are mounted on finely painted sturdy base
frame with easy machine interchangeability.
• Provision for torque measurement delivered at shaft
with
better
resolution/readability
&
Speed
measurement. Digital display for speed & torque to be
provided.
• Provision for Speed Torque characteristics and efficiency
at various loads.
• Should be able to draw all graphs.
• Facilitates easy and safe wiring by students.
• Study of Full bridge controlled / uncontrolled converter,
Half bridge controlled / uncontrolled converter.
• Study of Motor speed control using Thyristor /IGBT
The Panel to house the following components:
•
•
•
•
DOL Starter panel
DC voltmeter panel
DC ammeter panel
Power supply panel
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 87 of 115
1
1
Sl.
No
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Ref.
• Thyristor /IGBT power module
Qty
b. Accessories: Required number of patch cords and other
necessary accessories to be provided.
c. Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
d. Spare Parts:
Set of spare parts recommended for two years normal
operation. List of spare parts to be enclosed.
NOTE : Following documents are mandatory and are to be
submitted along with Technical Bid :
20.1 4/42
Work Table
for Thyristor /
IGBT
controlled DC
trainer
21
Thyristor
/
IGBT
controlled AC
trainer
4/43
1. Front & Back Panel drawing for detailed layout of Input /
Output terminals, Power switches, Metering with schematics.
2. Circuit drawings of complete Test Rig.
Work Table:
Work Table of dimension approximately 1200 – 1250 mm (L) x
600 – 650 mm (W), 740 - 780 (H) with powder coated suitable to
mount above trainer to be supplied. Work table to be comprised
of Table Top (18mm thickness) with smooth surface finish, MS
tubular frame (16 gauge), 3 drawers and castor wheels with
locking mechanism so that the table can be easily moved.
a. Thyristor / IGBT controlled AC trainer with powder coated
sturdy table top Aluminum flat demo panel system of dimension
940-1000 mm(L) x 280 – 320 mm(W) x 520 – 560 mm(H)
containing Motor Drive 2HP with VVVF control.
Features:
•
•
•
•
•
•
Aesthetically prepared colour printed water resistant
poly carbonate overlays with electrical circuit schematic
drawn for easy understanding. All test points and tags
well printed in colour.
Should have 4 mm sturdy shrouded banana patch cords
and shrouded arrangements.
All machines are mounted on finely painted sturdy base
frame with easy machine interchangeability.
Provision for torque measurement delivered at shaft
with
better
resolution/readability
&
Speed
measurement. Digital display for speed & torque to be
provided.
Provision for Speed Torque characteristics and efficiency
at various loads.
Should be able to draw all graphs.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 88 of 115
1
1
Sl.
No
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Ref.
• Facilitates easy and safe wiring by students.
Qty
The Panel to house the following components:
•
•
•
•
Motor, alternator panel
AC voltmeter panel
AC ammeter panel
Thyristor / IGBT controlled AC drive panel
b. Accessories: Required number of patch cords and other
necessary accessories to be provided.
c. Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
d. Spare Parts:
Set of spare parts recommended for two years normal
operation. List of spare parts to be enclosed.
NOTE : Following documents are mandatory and are to be
submitted along with Technical Bid :
1. Front & Back Panel drawing for detailed layout of Input /
Output terminals, Power switches, Metering with schematics.
2.Circuit drawings of complete Test Rig.
21.1 4/43
Work Table
for Thyristor /
IGBT
controlled DC
trainer
Work Table:
Work Table of dimension approximately 1200 – 1250 mm (L) x
600 – 650 mm (W), 740 - 780 (H) with powder coated suitable to
mount above trainer to be supplied. Work table to be comprised
of Table Top (18mm thickness) with smooth surface finish, MS
tubular frame (16 gauge), 3 drawers and castor wheels with
locking mechanism so that the table can be easily moved.
1
22
Electrical
Electrical Table for experiments / Test Bench:
Table
for
experiments / Electrical workbench antistatic to enable easy, fast and accurate
Test Bench
testing of different Electrical equipment. . Three phase 415V /
Single phase, 230 Volt, 50 Hz input supply sockets to be
provided.
3
4/155
&
4 /156
Consist of 3 partitions as below:
1. Bottom structure: Work Table of dimension approximately
1200 – 1250 mm (L) x 600 – 650 mm (W), 740 – 780 (H) to
be comprised of Table Top with antistatic rubber sheet
(18mm thickness) and smooth surface finish, MS tubular
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 89 of 115
Sl.
No
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Qty
Ref.
frame (16 gauge), 3 drawers and castor wheels with locking
mechanism so that the table can be easily moved.
2. Middle Cabinet structure of dimension 250 -300mm (H) on
top of table top to house power sources and MCBs etc.
3. Top Cabinet structure of dimension 250 -300mm (H) to
house different electrical equipment.
The following components to be housed in the Electrical
workbench
• Regulated DC power supply: 0 to 25 V minimum
• Unregulated DC power supply: 0 to 250 V
• Auto transformer: 0 to 415V, Current: 0 to 5A
• Single phase multifunction meters: 0 to 230 V, Current: 0
to 5A
• Three phase multifunction meters: 0 to 415V, Current: 0
to 5A
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 90 of 115
Enclosure - IV
LOT – 4 ELECTRICAL APPLIANCES:
6.
ELECTRICAL APPLIANCES
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Qty
Ref.
4/24
Fan
Ceiling Fan of AC 230 V, 1200 mm blades
2
4/115 Electric Hot plate 1500W, 220V with temp control
3
4/116 Electrical Kettle
Electrical Kettle Cordless with 360 degree rotational base and a
3
capacity of 1.7 litres
Stainless steel body, Concealed stainless steel heating element,
Water level gauge, Auto off on boiling, On/Off switch with light
indicator, 1000 Watts 230V power
4/117 Electric Iron box Automatic Iron box with minimum 1200Watts, 230V, Variable
3
steam control, and auto shut off and temp control.
4/118 Immersion
Immersion heating coil set consisting of 1000W, 230V
3
heater
4/119 Geyser
Geyser of minimum 25 litres capacity – 230 V (Storage type)
2
7.
4/120
Induction stove
8.
4/121
Microwave Oven
9.
4/122
Electric Cooker
Automatic Electric Rice Cooker 1.8 Litre Capacity (Raw Rice) 700
Watts, 230 V, Single phase, AC Electric supply, Teflon coated
cooking pan Cooking indicator, Detachable power cord Auto
shut off
2
10.
4/148
240v, 80W
2
11.
230 V, 4 FT, Electronic choke 40W
7
12.
4/149
&
4/160
4/150
Sodium vapor
Lamp fitting
Florescent lamp
fitting Tube Light
240 V, 80 W
2
13.
4/158
Mercury vapor
lamp fitting
Domestic water
pump with
starter
Water Pump Single Stage, Self-priming type, with Manganese /
Bronze impellers. Steel shafts and close grained Cast Iron parts.
Capacity of 1 HP
3
14.
4/159
Electric Toaster
Auto Pop Electric Toaster, 2 Slice capacity, 250 Watts, 230 V,
Single phase, AC Electric supply, Auto pop up, Cool touch body
Variable browning control, Cord storage, 250 W Heating
Element & Heating adjustment
2
15.
4/162
Washing machine Semi automatic of minimum 3.5 Kg Capacity,
Minimum 2 wash program, 240V 50 Hz AC Power supply
2
16.
4/163
Washing machine Fully automatic of minimum 3.5 Kg Capacity,
Minimum 8 wash program, 240V 50 Hz AC Power supply
2
17.
4/164
Semi Automatic
Washing
machine
Automatic
Washing
machine
Wall Fan
Wall fan of 18" sweep blade size
3
Sl.
No
1.
2.
3.
4.
5.
Electric Induction stove of minimum 120 W to 2000W 8 bands
adjustable power, Digital display to show time, power & temp,
Minimum temperature of 70 to 270 deg, 8 bands adjustable,
with Multi function & timer.
Micro Oven of minimum 30 Litres capacity convection type.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 91 of 115
2
2
ELECTRICAL APPLIANCES
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
18.
3/1
P.A Amplifier
19.
3/8
T.V. colour set
Full set of public address system with 5 cordless Mics & 2 set of
column type Loud speakers with wall mounting brackets
Specification:
Power output: 160W
Outputs: Preamp 200 mV/600 Ω, Line 1V/1 KΩ
Speaker Outputs: 4 Ω,8 Ω,70 V & 100V
Power Supply: AC:220-240V 50/60Hz or DC: 24 V
I. LED Smart TV with the following specification.
c) Screen size: 42 inches (107 cms) LED Display
d) Screen Resolution: Minimum 1920 x 1080p
e) Colour System: PAL, SECAM, NTSC
f) Display Resolution: Full HD
g) Backlight Module: LED
h) Ethernet Connection facility
i) Wi-Fi Connectivity facility
j) Access to Social networks like Twitter, Skype etc.
k) View Angle: 88-90 Degree (Right/Left), 88-90 Degree
(Up/Down)
l) HDMI Connections: Minimum 4
m) USB ports: Minimum 2
n) USB Play: MPEG1 / MPEG2PS/ MPEG2TS/ MP4Part10/
MP4Part2/ AVI(XVID)/ MOV/ WMV/ MKV/ WEBM/
3GPP/ MP3/ WMA/ WAV
o) Headphone Out facility
p) Intelligent MPEG Noise Reduction
q) Other features: Motionflow, Intelligent Picture, ,
Advanced Contrast Enhancer, 3D Comb Filter, Clear
Phase Speaker, Power Saving Modes, Parental Control
Accessories: Remote Control, Batteries
Power requirement: AC:220-240V, 50 Hz
II. LED TV with the following specification.
2
1
1
r)
s)
t)
u)
v)
w)
x)
y)
Screen size: 40 inches LED Display
Screen Resolution: Minimum 1920 x 1080p
Colour System: PAL, NTSC
Display Resolution: Full HD
Backlight Module: LED
HDMI Connections: Minimum 2
USB ports: Minimum 1
USB Play: MPEG1, MPEG2PS, MPEG2TS, AVCHD, , AVI
(XviD), AVI (Motion JPEG), WMV9, MKV, WEBM
z) Intelligent Noise Reduction
20.
3/21
Inter com
System
Accessories: Remote Control, Batteries
Power requirement: AC:220-240V, 50 Hz
Full set of Intercom system with 10 nos of push Button
telephone set having 6 to 11 station capacity, All – master
system or any combination of masters and remotes, multiple
simultaneous conversations, Selective electronic tone calling
(For master only), masters can call any station in system, remote
station can only calls its associated master station.
Intercom system with tone/pulse switchable, led status
indication and work without operator.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 92 of 115
2
ELECTRICAL APPLIANCES
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
21.
3/25
Push button
telephone set
22.
3/28
T.V. Camera
Color
Push button telephone set with international Standards features
like caller-ID, 16 digit LCD display, 30 incoming memory, 5
outgoing memory, Real time clock with year, date & month
display, conversation time display, redial memory, redial call
back, ringer volume control, Tone/pulse switch able.
Full set of Handy cam corder with & Other accessories with
•
•
•
•
•
•
•
•
•
•
2
2
240GB hard disk
1920 x 1080 full HD
10x Optical Zoom
120x Digital Zoom
HDMI & USB Terminal facility
HD/SD Video codec
Movie recording on memory stick and SD/SDHC memory
card
CMOS Image sensor
Dolby digital stereo 5.1 channel audio format
LCD display
Accessories: Carry case, AC Adaptor, Rechargeable Battery Pack,
USB Cable, HDMI Cable
Power requirement: AC:220-240V, 50 Hz
23.
3/29
Cord less
Telephone set
Digital Cordless Telephone with caller ID containing handset,
base, battery, charger of 2.4GHz Frequency of following
Specification:
Specific Channel Numbers: 90 Channels
Number of Lines: 1 Line
Power Source for Base unit : AC adapter
LCD (Handset), 5 hour talk time, Speaker in handset, Illuminated
Display Handset, Caller ID with 50-Name & Number Call Log, 5
Redial Memory, Clock/Alarm.
2
24.
3/83
Loud Speakers
2 Way Loudspeakers with woofer with the following
Specification:
2
•
•
•
Peak Power: 320W
RMS Power: 120W
Frequency Response: 35Hz - 30,000Hz
25.
3/84
Microphone
Wireless Microphone with wireless receiver for enhanced
mobility.
Frequency Response: 50 -15,000 HZ
Impedance: 500 Ohm
Working distance: 10 to 30m
8
26.
3/85
Headphoneearphone
HEADPHONE- EARPHONE (One set consists of One each)
8
Sets
HEAD PHONE WITH MICROPHONE:
Type: Closed, dynamic, Bluetooth Stereo
Frequency Response: 10-24,000 Hz
Power Source / Battery Type: Built-in Lithium ion Rechargeable
Battery.
Battery Life: Approx. 30 hrs Communication Time
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 93 of 115
ELECTRICAL APPLIANCES
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
EARPHONE:
Superb sound quality with Digital Sound Enhancement Engine
Type: Closed
Power Handling Capacity: 100mW
Frequency response: 5-25,000 Hz
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 94 of 115
Enclosure – V
LOT-5 ELECTRICAL & ELECTRONIC EQUIPMENT:
Sl.
No
1
ELECTRONIC EQUIPMENT
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Qty
Ref.
3/4
Sweep generator SWEEP GENERATOR WITH X-Y DISPLAY WITH MARKER
3
with X-Y display
Sweep: 25 MHz to 240MHz, Digital Readout of selected channel
with marker
on LED display
Output Level: ≥ 315 mV r.m.s
Marker Generator:
RF Marker : 30-240MHz
CRT Display:
CRT: 14cms rectangle flat faced CRT
2
3/11
Signal Injector
3
3/18
Logic Probes
4
3/44
Power Supply
Unit
5
3/50
Cell phone PCB
holder - Lot
6
3/64
7
3/65
8
3/66
Solenoid with
core
Electric bells set
of different types
Battery
Eliminator
9
3/86
Receiver aco real
kit
Set of spare parts recommended for 2 years normal operation.
Please indicate the detailed list of spares.
SIGNAL INJECTOR
Pen / portable type with Battery operated to inject the signals
by pressing. The injectors have signal source of 1 KHz Audio
signal
LOGIC PROBES for analyzing and troubleshooting the logical
states (Boolean 0 or 1) of a digital circuit.
Display: LED
Output voltage: Fixed ± 5 V, ± 12 V DC
Ripple: < 2mV,
Power supply: 230 V 50Hz.
CELL PHONE PCB HOLDER
To hold the PCB’s of cell phone of different types & minimum 4
types
Solenoid valve with core
One Set consisting of Eight Nos of different types of Electric
bells of both AC & DC for demonstrating the working function.
BATTERY ELIMINATOR
The output voltages is selectable from 0-2V DC, 4V DC, 6V DC,
8V DC, 10V DC, 12V DC at 3A. Display of voltages & Currents
through voltmeter and ammeter.
Receiver aco real kit showing all the sections of radio AM/FM
receiver separately with block diagrams printed on front panel
showing its output. Each stage out put are brought out the
terminal as a test point to observe its output and working
principles.
AM radio receiver: Super heterodyne
Frequency Range: 500 Khz to 1 MHz
FM radio receiver:
Frequency Range: 88 Mhz to 108 MHz
•
•
•
To study the theory and practice of active circuits used
in analog telecommunication related to AM/FM radio
receivers Meter
To study AM radio receiver
To study of image frequencies for AM
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 95 of 115
8
8
10
1 Lot
4
8 sets
8
3
Sl.
No
10
11
12
13
14
ELECTRONIC EQUIPMENT
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Qty
Ref.
• To study FM radio receiver
• To measure the frequency response of Audio amplifier
3/87
Service Oscillator SERVICE OSCILLATOR
3
Servicing Oscillator is designed for use in servicing of Televisions,
Valve Radio and Transistor Radio Receivers.
Specifications;
Accuracy of Frequency: Approximate ±1%.
Internal Modulation Frequency: Approximate 400Hz.
% Modulation: Approximate 30%.
Power Source: 230V 50Hz AC or 9 Volt DC
3/88
Signal Tracer
SIGNAL TRACER
3
Operating voltage :230V AC / 12V DC
Power input
: 28W RMS,
Input channels : 2 Mic x 0.5 mV / 2.5 Kohms
4/40
Battery Charger
BATTERY CHARGER
2
With variable output of 1KW
Input Operating Voltage of 230V, 50 Hz & Output voltage
selectable 6V, 12V & 24V batteries
Portable with digital display of voltage and Current using
Voltmeter and Ammeter with ON/OFF switch, Fuse, Indicator for
supply ON overload, reverse polarity protection with heavy duty
terminals, Battery connecting leads and clamps 1 set along with
charger, Hydrometer, Battery Cell voltage tester to check the
voltage Operating Voltage of 230V, 50 Hz,. are to be supplied.
The charger unit provided with trolley to move from one place
to other.
4/102 Wheat stone
Wheat Stone Bridge with DC power supply and Galvanometer
2
bridge
Technical Specifications:
DC Power Supply : 5V
Resistance : 80 Ohm
Type : Variable
Range : 0 – 10 KOhm
4/108 Load bank
Resistance type Load bank with on board switches to provide
2
load for various experiments. Trolley for flexible movement to
be provided.
15
4/111
DC power supply
16
4/113
Servo Voltage
Stabilizer
Load range: 0 - 5 KW in different steps
DC power supply
Good Regulation and Low Ripple
Technical Specification:
Output: 0-100V, 5A.
Protection: Short and Over load
Indication: Digital Meter for Voltage and Current Indication.
Power Supply: 230 V ±10 %, 50Hz
SERVO VOLTAGE STABILIZER
Demonstration model showing the working principle of Servo
stabilizer with Servo motor and voltage corrector
Specifications;
Input Voltage Range: 150V to 230 V AC., Single-phase
Output Voltage: 220VAC. Nominal, Internally Settable to 220V
to 240V.
Output Voltage Indication: By Digital Voltmeter
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 96 of 115
3
2
Sl.
No
17
18
19
ELECTRONIC EQUIPMENT
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Qty
Ref.
Electronic under/over voltage Protection
Upper Limit: 230V AC
Lower Limit: 150V AC
Over Load Indication: By LED
Rating: 1 KVA.
4/145 Motor Winding
Armature winding of FHP AC motor set for motor winding
1
Set
practice. The set should contain the following:
• Shaft
• Insulating paper
• Bearings with assembly manual
• Rotor
• Copper coil
• Body
1
Armature winding of FHP DC motor set for motor winding
practice. The set should contain the following:
• Brush holder
• Shaft
• Insulating paper
• Commutator
• Bearings with assembly manual
• Carbon brush
• Rotor
• Copper coil
• Body
4/146 Auto
Auto transformer three phase
1
transformer
Output voltage: Variable 0-470V AC at 6A
Input Voltage: 400V Three Phase, 50 Hz AC
4/161
Earth Resistance
Tester
EARTH RESISTANCE TESTER
Earth Resistance: 0-2000 Ω
Earth Voltage: 0-200V
Display: Digit display
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 97 of 115
2
Enclosure-VI
LOT-6 ELECTRONIC TRAINERS:
Sl.
No
1
ELECTRONIC TRAINERS
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Ref.
Digital Storage Oscilloscope.
4/26 & Oscilloscope 3/2
Digital
30 MHz Digital Storage Oscilloscope with
Qty
10
Bandwidth: 30MHz
Channels: 2
Rise Time: <10ns
Equivalent Sampling Rate: 20 GSa/s
Memory Depth: 32Kpts
Maximum Input Voltage: 400V peak
Input Coupling: AC, DC, GND
Triggering Modes : Auto/Normal/Single
Triggering Types: Edge, Pulse Width, Slope, Video, Alternate
Display: LCD Colour
Power supply : 230 V +/- 10 % 50 Hz
USB Support: Yes
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
2
3/5
Bread Board
trainer with kits
Set of spare parts recommended for 2 years normal operation
Bread Board trainer with built-in power supply to perform
experiments using Resistors, Capacitors, Inductors, Transistors,
Diode, LED, IC etc. and to have Hands on learning by
constructing different circuits.
•
•
•
•
Breadboard panel with minimum 1200 tie points and
400 distribution points.
Connections through Sturdy banana sockets and patch
cords.
Built in Variable power supply and Function generator to
perform experiments.
Manual containing different types of experiments using
breadboard to be supplied.
Built-in Power Supply: +-5V, +-12V, variable 0 to +-12V
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 98 of 115
2
Sets
Sl.
No
3
ELECTRONIC TRAINERS
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Ref.
supported with observator tables for easy learning.
3/22 &
3/23
C.R.O. Trainer kit
Set of Jumper wires, Resistors, Capacitors, Inductors,
Transistors, Diodes, ICs, LEDs and spares recommended for
conducting experiments for 2 years to be provided.
C.R.O. Trainer kit.
C.R.O. Trainer kit with Fault creation & rectification provided.
Qty
4
Bandwidth: 25-30 MHz
Channel: Dual Channel
Maximum Input Voltage: 300V peak
Triggering Modes : Auto/Normal
Coupling: AC
Slope: Positive or Negative
Accuracy: +-3%
Input Coupling: AC,DC, GND
Risetime: <18 ns
Component Tester:
Test Voltage – Max 8.6 V, Test Current – 8mA
Power supply : 230 V +/- 10 % 50 Hz
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
4
3/3
Set of spare parts recommended for 2 years normal operation
Power Supply set Power Supply Set 0-30V & 0-300V DC
Range: 0-30Volts Variable and 0-300Volts Variable DC Power
supply with Overload & Shot circuit Protection.
8
Ripple Noise: < 2mVrms
Display: Digital for voltage & Current reading
Operating Temperature: 0 to 45 deg
Power supply : 230 V +/- 10 % 50 Hz
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
5
3/6
AC Bridge
rectifier Trainer
Set of spare parts recommended for 2 years normal operation:
A.C Bridge rectifier Trainer kit to study characteristics of
• Half wave rectifier
• Full wave rectifier
• Bridge rectifier
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 99 of 115
1
Sl.
No
ELECTRONIC TRAINERS
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Ref.
Qty
Connections through Sturdy banana sockets and patch cords.
Test points to be provided.
Power supply : 230 V +/- 10 % 50 Hz
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
6
3/7
TV Trainer kit
Set of spare parts recommended for 2 years normal operation
LCD/LED Television Trainer to study working principle of
LCD/LED Television.
•
•
•
•
4
Study the block diagram and operating principle of
LCD/LED TV
Study the functions of controls on Remote
Study of waveforms/signals of different sections
Study of switch faults and troubleshooting in different
sections
Reception: NTSC/PAL
Display: 22’’ LCD /LED
List of faults: 12V supply, 5V supply, Standby voltage, Monitor,
USB, Audio/Video, LCD.
Interface: USB, HDMI
Trigger Modes: Auto, Normal, Single
On Screen Display to set: Volume, Brightness, Contrast, Colour,
Channel & Band selection, Tuning.
Test Points & faults to be provided.
Power supply : 230 V +/- 10 % 50 Hz
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
7
3/9
Pattern
generator
Set of spare parts recommended for 2 years normal operation:
Colour Pattern Generator:
System: PAL
Patterns : Minimum - Vertical bar, horizontal bar, dots, Circle
pattern.
Frequency: 1 Khz Sine wave
Video carrier:
Lower VHF band : 40-60 MHz
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 100 of 115
3
Sl.
No
ELECTRONIC TRAINERS
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Ref.
Upper VHF band : 170-230 MHz
Power supply: 230 V ±10 %, 50 Hz
Qty
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
8
3/10
Signal generator
Am/Fm
Set of spare parts recommended for 2 years normal operation:
Signal Generator AM/FM
Modulation: AM, FM
Frequency Range: 1 Hz - 10 MHz
Output Waveform: Sine, Square, Triangle, Ramp, Pulse
Square Wave Rise & Fall time: < 60ns
CMOS/TTL Output Rise & Fall time: < 30ns
Display: LCD
Output Impedence: approximately 50 ohms
Output Voltage: approximately 20Vpp
3
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
9
3/12
Distortion meter
Set of spare parts recommended for 2 years normal operation:
Distortion Meter to detect frequencies that cause harmonic
distortion.
1
Frequency: 20 Hz to 20 KHz
Input Voltage: 600mv - 50 Vrms
Input Impedance: <= 60Kohms
Output Impedance: <= 10Kohms
Display: LCD/LED
Power supply: 230 V ±10 %, 50 Hz
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
10
3/13
Strain gauge
with load cell
Set of spare parts recommended for 2 years normal operation:
Strain Gauge Trainer
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 101 of 115
2
Sl.
No
ELECTRONIC TRAINERS
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Ref.
• Study of Strain measurement using Strain gauges and
cantilevel assembly.
• Gauge factor determination, Strain indicator,
Displacement measurement.
• Test points to observe input output of each block with
High repeatability and reliability.
Qty
Maximum bearable weight : approximately 400 gm
Display: LCD/LED
Accuracy: 0.01mm
Gauge Factor: 2.1
Power Supply : 230 V ±10 %, 50 Hz
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
11
3/15
DVD Trainer kit
Set of spare parts recommended for 2 years normal operation
DVD Player Trainer
•
•
•
•
1
Study the block diagram and operating principle of DVD
Player
Study of circuit diagram and functions
Study and observation of waveforms of different
sections
Study of switch faults and troubleshooting in different
sections
System: PAL, NTSC
Sound System: External speaker and Headphone
Circuit Block: On board/ front panel block diagram.
Test Points to be provided
Power Supply: 230V ± 10%, 50Hz
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
12
3/16
Micro Processor
Training kit
Set of spare parts recommended for 2 years normal operation
8085 / 8086 Microprocessor Training Kit to provide basic
information about 8085 and 8086 microprocessor and
peripherals
CPU: 8085 / 8086 Microprocessor
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 102 of 115
3
Sl.
No
ELECTRONIC TRAINERS
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Ref.
ROM: Minimum 64Kbytes EPROM with battery backup
Display: LCD/LED
Keyboard: Hexadecimal
Interface: RS232 C
Bus: All address, data & control lines
Faults: Pins of Address bus, Data bus
Power Supply: 230V ± 10%, 50Hz
Qty
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
13
3/17
&
4/32
Linear Digital I.C
Trainer
Set of spare parts recommended for 2 years normal operation
Linear Digital I.C Trainer with built-in DC power supply of 5V. On
board resources such as logic switches/inputs for providing
inputs to digital ICs.
5
Digital Circuits to be covered: Minimum - Basic logic gates,
Universal gates, Flip-flops, Counters, Multiplexers /
Demultiplexers,
Encoder / Decoder, Full/Half Adder &
Substractor.
Connections: Easy interconnections between circuits
Indicators: LCD/LED
Power Supply: 230 V ±10 %, 50Hz
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
14
3/19
Frequency
Counter
Set of spare parts recommended for 2 years normal operation
Frequency counter to study the fundamental principle and
functioning of Frequency Counter.
Technical specification:
Frequency range: 10 Hz to 1 GHz with minimum 2 steps, variable
control between steps
Input Impedance: 50 -60 ohm
Input Coupling: AC
Frequency display: LCD/LED
Power supply: 230 V AC+/- 10% 50 Hz
Instruction Manual:
Should contain Information on features, operation and
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 103 of 115
3
Sl.
No
15
ELECTRONIC TRAINERS
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Qty
Ref.
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
3/20
Set of spare parts recommended for 2 years normal operation
A.F/R.F Oscillator A.F/R.F OSCILLATOR
To study both Audio frequency (AF) and Radio Frequency (RF)
oscillators.
3
Radio Frequency Range: 10 MHz to 150 Mhz
Audio frequency Range: 10 Hz to 20 KHz
Modulation: AM/FM
Waveform : Sine, Square, Triangle
Display: LCD/LED
Power Supply : AC 230 V ±10 %, 50 Hz
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
16
3/24
&
4/29
Function
Generator
Trainer Kit
Set of spare parts recommended for 2 years normal operation
Function Generator Trainer
To study working principle & various faults of Function
Generator. The Trainer to allow students to produce the
different waveforms and to understand the concept of their
generation.
•
•
•
•
•
Study of Sinusoidal Waveform Generation.
Study of Triangular Waveform Generation.
Study of Square Waveform Generation.
Study of TTL Waveform Generation.
Fault creation and troubleshooting
Frequency range: 1Hz to 100 KHz
Waveforms: Sine, Square, Triangle, TTL
Test Points: Faults & Test points to be provided
Display: LCD/LED
Power Supply : 230V AC, 50 Hz ±10%
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 104 of 115
3
Sl.
No
17
ELECTRONIC TRAINERS
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Ref.
3/30
Cellular
telephone set
trainer
Set of spare parts recommended for 2 years normal operation
Cellular Telephone Trainer
Qty
2
To study working principle & various faults of Cellular telephone.
•
•
•
•
•
Understanding of GSM technology, its network, GSM
capability & data services
To Study Mobile Transmission & Reception concepts
To Study Mobile charging concepts
To Study different faults & troubleshooting
To Study Bluetooth concepts
Cellular System : GSM 900/1800
Rx frequency band: 1710 – 1785 Mhz
Tx Frequency band: 1805 – 1880 Mhz
Channel spacing : 180 – 210 Khz
On board sections : keypad, SIM, charging circuit, LCD/LED
Display etc.
Power Supply: 230 V ±10%, 50Hz
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
18
3/32
SMPS Trainer
Set of spare parts recommended for 2 years normal operation
SMPS Trainer
To study working principle & various faults of SMPS (Switched
Mode Power Supply).
•
•
•
Study of Regulation
Study of various faults & their removal in SMPS circuit.
Block diagram printed on front panel
Input: 230 V AC ±10%, 50 Hz
Output: +- 12V / 5V DC
Test Points: to be provided
Power Supply: 230 V ±10%, 50Hz
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 105 of 115
2
Sl.
No
19
ELECTRONIC TRAINERS
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Ref.
3/35
Electrical &
Electronics
system Trainer
Set of spare parts recommended for 2 years normal operation
Electrical & Electronics system Trainer
Electrical & Electronics system Trainer to study the following:
•
•
•
•
•
•
•
•
Qty
2
Study of Resistance, Current and Voltage measurements
Study of Ohms law
Study of Kirchoff’s Laws
Study of R-L, R-L-C Series and Parallel circuits
Study of Norton, Thevenin, Superposition, Tellegan,
Millman theorems
Study of 2 port Network parameters.
Study of Active & Reactive power measurements
Study of RMS value measurements
Power Supply: 230 V ±10%, 50Hz
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
20
3/36
Communication
system trainer
Set of spare parts recommended for 2 years normal operation
Communication system trainer to study Amplitude Modulation
& Demodulation and Frequency Modulation & Demodulation.
Amplitude Modulation & Demodulation
Signal Source: 300 hz to 3 Khz
Amplitude: 0 to 5 V variable
•
•
•
•
•
Study and observation of Amplitude Modulation
Study of Balanced modulator
Study of Envelope detector
Study of DSB modulation & demodulation with
Transmitted carrier, Suppressed carrier
Study of SSB modulation & demodulation
Frequency Modulation & Demodulation:
Signal Source: 1 Khz to 3 Khz
•
•
•
•
Study and observation of Frequency Modulation
Study of Varactor, Phase modulator
Study of Phase Locked Loop & Quadrature detector
Study of Pre-emphasis & De-emphasis.
Test Points: to be provided
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 106 of 115
2
Sl.
No
21
ELECTRONIC TRAINERS
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Qty
Ref.
Power supply: 230 V+/- 10% 50Hz
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
3/37
Set of spare parts recommended for 2 years normal operation
EPABX Trainer kit EPABX Trainer
(Electronic
To study working principle of EPABX (Electronic Private
Exchange)
Automatic Telephone Exchange).
Telephone instruments
required for training to be provided.
•
•
•
•
2
On board circuit diagram to be provided.
Switched Faults and Test Points to be provided.
Study of Trunk unit and ring detection.
Study of relay switching mechanism.
Standard Features: Tones such as Dial, Redial, Busy, Call
transfer, Do not disturb etc.
Dialing: DTMF, Pulse
Program Memory: Minimum 128 Kb
Power supply : 230 V ±10%, 50 Hz
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
22
3/41
EPROM Kit
Set of spare parts recommended for 2 years normal operation
EPROM TRAINER KIT
To provide practical and experimental knowledge of EPROM.
•
•
•
The schematic circuit diagram should be printed on
P.C.B. for all terminals, switches, components and power
supplies.
Supports all operations such as read, write, erase,
program etc.
Connections through Sturdy banana sockets and patch
cords.
Program Memory: Minimum 64 Kb
Display: LCD /LED
Power supply : 230 V ±10%, 50 Hz
Instruction Manual:
Should contain Information on features, operation and
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 107 of 115
1
Sl.
No
23
ELECTRONIC TRAINERS
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Qty
Ref.
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
3/42
A to D Trainer kit
Set of spare parts recommended for 2 years normal operation
A to D Trainer
Analog to Digital Converter with built in DC power supply.
Connections through Sturdy banana sockets and patch cords.
1
ADC: 4 or 8 bit
Types: Minimum Dual Slope, Ramp, Successive approximation
Output Indication: LED
Test Points: to be provided
Power Supply: 230 V ±10 %, 50Hz
24
3/43
D to A Trainer kit
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
Set of spare parts recommended for 2 years normal operation
D to A Trainer
Digital to Analog Converter with built in DC power supply.
Connections through Sturdy banana sockets and patch cords
1
D/A Conversion: 4 or 8 bit
Types: Minimum R-2R ladder, binary-weighted
Output Indication: LED
Power Supply: 230 V ±10 %, 50Hz
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
25
3/71
Transistor Tester
Set of spare parts recommended for 2 years normal operation
Transistor Tester to study and test different types of
Transistors.
•
•
•
Study of NPN & PNP Transistors
Short Circuit and Open Circuit test for NPN and PNP
transistors.
Study of characteristics of NPN Transistor in Common
Base, Common Emitter & Common Collector
Configurations
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 108 of 115
2
Sl.
No
ELECTRONIC TRAINERS
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Qty
Ref.
• Study of characteristics of PNP Transistor in Common
Base, Common Emitter & Common Collector
Configurations
• Test points to be provided.
Power Supply : 230 V ±10 %, 50 Hz
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
26
3/72
Set of spare parts recommended for 2 years normal operation
Universal IC Tester
Universal IC Tester to study the characteristics of Both analog
and digital ICs.
I.C. Tester
•
•
2
To test a wide range of Digital IC's like 7400, 7401, 7402,
7403, 7404, etc.
To test a wide range of Analog IC's such as 555, 556,
etc..
Display: LCD /LED / Seven segment display
Power Supply: 230 V ±10 %, 50 Hz
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
27
3/89
A.F. Oscillator
Set of spare parts recommended for 2 years normal operation
AF Oscillator
To study Audio frequency (AF) oscillator.
Audio frequency: 1 Hz to 1 MHz
Waveforms : Minimum Sine, Square, Triangle
Square Wave Rise & Fall Time: ≤ 120 ns
Pulse Duty Cycle: 10 to 90 %
Output Voltage: 18 – 22 Vpp
DC Offset: Approximately +- 5V
Display: LCD /LED
Power Supply : AC 230 V ±10 %, 50 Hz
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 109 of 115
3
Sl.
No
28
ELECTRONIC TRAINERS
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Qty
Ref.
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
3/90
Set of spare parts recommended for 2 years normal operation
Frequency Modulator to study different types of Frequency
Modulators.
Frequency
Modulator
2
Frequency range: 1Hz to 100 KHz
Modulators: Reactance, Varactor, Armstrong
Test points: to be provided
Display: LCD / LED
Power supply: 230 V+/- 10% 50Hz
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
29
4/25
Industrial PLC
trainer kit
Set of spare parts recommended for 2 years normal operation
Industrial PLC trainer kit
To study the working of PLC's used for industrial applications.
Connections through Sturdy banana sockets and patch cords.
Software in the form of CD to be provided.
The following experiments to be perfumed on PLC trainer:
•
•
•
•
•
•
Process Control
Water Level Control
Traffic Signal Control
Motor Speed Control
Home Automation control like Light Switching & Door
Bell Control
Elevator Control
Programming: Ladder
Interfacing: RS232C
Display: LED
Power supply: 230 V+/- 10% 50Hz
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 110 of 115
1
Sl.
No
30
ELECTRONIC TRAINERS
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Qty
Ref.
Set of spare parts recommended for 2 years normal operation
4/30
Discrete
Discrete component Trainer with built-in power supply to study
2
&
basic semiconductor devices. Connections through Sturdy
Component
3/14
banana sockets and patch cords.
trainer
Components: Resistors, Capacitors, Inductors, diodes, NPN&
PNP Transistors, BJT, FET, MOSFET etc.
Power Supply: 230 V ±10 %, 50Hz
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
31
4/31
Set of spare parts recommended for 2 years normal operation
Linear I.C. Trainer with built-in power supply to study different
types of Operational amplifiers. Connections through Sturdy
banana sockets and patch cords.
Linear I.C.
Trainer
1
Operational Amplifiers: Comparator, Schmitt Trigger, Inverting,
Non inverting, Summer, Difference, Differentiator, Log &
Antilog, Low Pass filter, High Pass filter, Band pass & Band Stop
filter, Samp & Hold, Timer
Power Supply: 230 V ±10 %, 50Hz
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
32
4/44
Experimental
Power
Electronics
Trainer
Set of spare parts recommended for 2 years normal operation
Experimental Power Electronics Trainer
To study Characteristics of Triac, UJT , SCR. Connections through
Sturdy banana sockets and patch cords
Power Devices :, Triac, UJT & SCR
Applications: Fan regulator, Temperature control, Timer, AC
power control, Switch & Relay
Power Supply: 230 V ±10 %, 50Hz
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 111 of 115
1
Sl.
No
33
ELECTRONIC TRAINERS
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Qty
Ref.
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
4/112
Inverter, sine
wave
Set of spare parts recommended for 2 years normal operation
Inverter, Sine Wave: To study about conversion of DC into AC.
•
•
•
•
•
To understand the function of Inverter
Different blocks can be explained like charging of
battery, DC to AC conversion.
To understand the charging of battery
To study the Inverter circuit
To study the different faults and there troubleshooting
in Inverter circuit
Output voltage: 220 V AC
Battery: 12V DC
Power: 1KVA
Main Supply: 230 V ±10 %, 50Hz
Instruction Manual:
Should contain Information on features, operation and
maintenance. Instructional manual having list of Experiments,
brief introduction, circuits, apparatus used, procedure,
tabulation etc. Well illustrated documents with clean figure,
theoretical explanation to be provided. Log of experiments
supported with observator tables for easy learning.
Set of spare parts recommended for 2 years normal operation
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 112 of 115
2
Enclosure-VII
LOT – 7 ELECTRICAL METERS:
Sl.
No
1
2
3
4
5
6
7
8
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Make
Ref.
4/85 & Digital Multi
Digital multi meter with pair of test leads, ISI STANDARD
3/48
meter
carrying case, battery, instruction manual and
spare fuse to measure AC - DC volts and
currents, resistance, continuity testing, palm size
with built-in tilt stand, 3½ digit – 1999 counts
display with 9v battery power
3/53
Digital Ohm
Digital Ohm meter Upto 10 M.ohm range, 3½ ISI STANDARD
meter
digit 7 segments LED display with over range
indication and 7 no of resolutions, 230V 50 Hz
AC power supply.
4/114 Rheostats Single Phase Tubular type Rheostats of following MEC/
&
set
ranges :
TOSHNIWAL/
3/68
a. 0-1 Ohm, 5 Amp,
ISI STANDARD
b. 0-10 Ohm, 5 Amp,
c. 0–25 Ohm, 1 Amp,
d. 0–300 Ohm, 1 Amp,
e. 0 – 1000 Ohm, 0.5 Amp
(one Set consisting of One each above)
3/73
DC/AC
Ammeter DC Digital portable type, 0-5 A range.
AE / MECO / ELC
Ammeter
/ UNITECH/
Ammeter AC Digital portable type, 0-5 A range.
INDOTECH/
ISI STANDARD
3/74
3/75
3/76
3/77
DC/AC
Ammeter
DC/AC
Ammeter
DC/AC
Ammeter
DC/AC
Ammeter
9
3/78
DC/AC
Voltmeter
10
3/79
DC/AC
Voltmeter
Ammeter DC Digital portable type, 0-500 mA
range.
Ammeter AC Digital portable type, 0-500 mA
range.
Ammeter DC Digital portable type, 0-1 mA range.
Qty
18
2
4 sets
3
3
AE / MECO / ELC
/ UNITECH/
INDOTECH/
ISI STANDARD
AE / MECO / ELC
/ UNITECH/
Ammeter AC Digital portable type, 0-1 mA range. INDOTECH/
ISI STANDARD
Ammeter DC Digital portable type, 0-5 mA range. AE / MECO / ELC
/ UNITECH/
Ammeter AC Digital portable type, 0-5 mA range. INDOTECH/
ISI STANDARD
3
Ammeter DC Digital portable type, 0-100 mA
range.
Ammeter AC Digital portable type, 0-100 mA
range.
Voltmeter DC/AC, Digital portable type, 0-5 V
range
3
AE / MECO / ELC
/ UNITECH/
INDOTECH/
ISI STANDARD
AE / MECO / ELC
/ UNITECH/
INDOTECH/
ISI STANDARD
Voltmeter DC/AC, Digital portable type 0-10 V AE / MECO / ELC
range
/ UNITECH/
INDOTECH/
ISI STANDARD
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 113 of 115
3
3
3
3
3
3
3
3
Sl.
No
11
12
13
14
15
16
17
18
19
20
21
22
23
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Make
Ref.
3/80
DC/AC
Voltmeter DC/AC, Digital portable type 0-50 V AE / MECO / ELC
Voltmeter
range
/ UNITECH/
INDOTECH/
ISI STANDARD
3/81
DC/AC
Voltmeter DC/AC, Digital portable type 0-500 V AE / MECO / ELC
Voltmeter
range
/ UNITECH/
INDOTECH/
ISI STANDARD
4/41
M.C.B
One each MCB type of
MDS / SIEMENS /
a. 2 pole 250V, 16 Amps rated mounted on
GLOSTAR/
MCB panel
ISI STANDARD
b.
3 pole 500V, 16 Amps rated mounted on
MCB panel
4/84
Analog multi Analog multi meter with pair of test leads,
AE / MECO /
Meter
carrying case, battery, instruction manual and
PROTECT /
accessories fuse to measure AC - DC volts &
METRAVI /
currents, resistance, continuity testing with 9V
MASTECH/
power and measuring range 0 to 1000 M ohms
ISI STANDARD
and testing voltage of 2.5 to 500 volts
4/86
A.C.
Multi Range: 0-250- 500 V AC, MI with anti
AE / MECO / ELC
Voltmeter, MI parallax mirror, Knife edge pointer, portable type / NIPPEN /
BRISTEL /
UNITECH
/INDOTECH/
ISI STANDARD
4/87
Milli
Portable milli voltmeter with centre zero 100 – AE / MECO / ELC
Voltmeter
0 -100 millivolts, portable type with anti parallax / NIPPEN/
centre zero
mirror, Knife edge mirror
ISI STANDARD
4/88
D.C Milli
Portable milli ammeter of range: 0 - 500 mA
AE / MECO / ELC
ammeter
portable type with anti parallax mirror, Knife
/ NIPPEN/
edge mirror
ISI STANDARD
4/89
D.C.
Portable Ammeter of Range: 0 – 1 A,MC,
AE / MECO / ELC
Ammeter MC portable type with anti parallax mirror, Knife
/ NIPPEN/
edge mirror
ISI STANDARD
4/90
Ammeter MC Portable, MC, Range:
AE / MECCO /
0-5 A
UNITECH
/INDOTECH/
ISI STANDARD
4/91
Ammeter MC Portable, MC, Range:
AE / MECCO /
0-15-25 A
UNITECH/
INDOTECH/
ISI STANDARD
4/92
A.C. Ammeter Portable , MI, Range 0-5 A
MECO / EIC /
MI
NIPPEN /
BRISTEL/
ISI STANDARD
4/93
A.C. Ammeter Portable, MI, Class-1, Multi Range
MECO / EIC /
MI
0-15-25 A
NIPPEN /
BRISTEL/
ISI STANDARD
4/94
K.W. Meter
Portable watt meter dynamo motor type of multi AE / MECO / ECI
range 0-1-3 KW, 2.5/5A with anti parallax
/ NIPPEN /
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 114 of 115
Qty
3
3
2 sets
4
2
2
2
2
2
2
2
2
2
Sl.
No
24
25
26
27
28
29
30
31
32
Project: Upgradation & Modernisation of RGPCPA, Ulaanbatar, Mongolia – IInd Phase
Annex
ITEM
Brief Specification
Make
Ref.
mirror and knife edge pointer.
INDOTECH/
ISI STANDARD
4/95
A.C. Energy
Induction type, Single phase, 240 V, 50 Hz, 5A
TECHNO /
Meter
panel mounting type.
UNITECH /INDO
TECH/
ISI STANDARD
4/96
Single Phase
Portable Digital power factor of 0.5 lag to 0.5
AE / MECCO/
power factor lead, 0-110- 230 Volts, current of 1-5 Amps
EIC / NIPPEN /
meter
INDOTECH /
MEC/
ISI STANDARD
4/97
Frequency
Digital frequency meter with main frequency
ISI STANDARD
Meter
range of 30 Hz to 70 Hz & 0.01 resolution, 180 230V AC power supply.
4/99
Growler
Inside & Outside Growler set of two consisting of MASTECH/
one each of .
MEC/
a. Growler Outside: To test DC motor armature, ISI STANDARD
provision with drop test current measurement
across segments 240 volts 1 ohms 50 Hz.
b. Growler Internal: To test AC starter winding
with indicator 240 volts 1 ohms 50 H z.
4/100 Tong tester/
0 - 5 -10 Amps, provision to measure voltage of ISI STANDARD
Clamp meter 0 -250 - 500 volts digital type
4/101 Megger set
One each Generator type Megger set of range
WACO/MASTEC
500 Volts & 1000Volts
H/
ISI STANDARD
ISI STANDARD
4/123 Flux meter
Digital flux meter : To measure DC Magnetic
fields, voltage integration, ferro magnetic
detectors, EMF Tester.
Specification:
Input Power : 240 V, 50 Hz, 25VA.
Input Resistance : 10 Kilo Ohms
Output Resistance : 1 Kilo Ohms
Output Voltage: 1 Kilomaxwell turns
Display: 3½ digit LED/LCD
4/124 Lux meter
Lux meter with 3 1/2 digits LCD display,
KUSUM/MASTEC
maximum reading value display 1999, 0-50000
H/
Lux range, 1Lux resolution.
LUTRON/
ISI STANDARD
4/157 Clamp on
Digital Clamp meter with accessories like test
KUSAM – MECO/
Ammeter
leads, carrying case, manual. etc. with 3 1/2 digits ISI STANDARD
2000 counts display to measure AC current up to
600A, AC Voltage, DC voltage, resistance, diode
test..etc
End of Section - V
TENDER NO: HMTI/PROJ/RGSPA-II/S-001/2014 Dated: 27.10.2014
Page 115 of 115
Qty
2
2
2
2 set
2
2 sets
2
2
3