8-2011
NREZ016
CAL. Z016 (R23 SERIES)
Start/Stop
S1
Set
S3
S2
LIGH
T
RESET
S3
24 HOUR
RESET
P
1. Press and hold Button S1 or S2. Then press Button S3 to switch the display.
* The time display format in either 12-hour indication or in 24-hour indication can be selected
alternately.
* Under the 12-hour indication format, "P" mark
appears in the afternoon, but no AM mark appears in the morning. Under the 24-hour indication format, no mark appears on the display.
S1
LIGH
T
ST/STP
* Press and hold Button S3 for 3 seconds to show
the ALARM TIME.
* Press and hold Button S1 to show the MONTH/
DATE or DATE/MONTH. Release Button S1 to return to the NORMAL TIME display.
* Press Button S3 at any time to return to the NORMAL TIME display.
P
E
MOD
S2
PRESS AND
HOLD
NORMAL TIME
T
LIGH
E
MOD
PRESS
M O N T H / DAT E
T
LIGH
RESET
S2
E
PRESS
DAT E / M O N T H
■ H OW TO S E T A L A R M T I M E
T
LIGH
RESET
S2
E
MOD
S3
S1
ST/STP
P
NORMAL TIME
PRESS
AND
HOLD
S3
S3
LIGH
T
PRESS
ST/STP
S2
E
MOD
RESET
S2
ST/STP
P
S1
ST/STP
T
P
MOD
1. From NORMAL TIME display, press and hold Button S3 for 3 seconds to show the ALARM TIME
display.
2.Press Button S3 again to set the time and calendar. The second digits start flashing.
3. Press Button S2 to set the second digits to “00.“
* When the second digits count any number
from “ 30” to “ 59,” one minute is added.
4.Press Button S1 to move on to minutes setting.
The minute digits start flashing.
* Selection of the digits to be adjusted (flashing)
is made in the order below by pressing Button
S1 and then pressing Button S2 to be set.
* One digit (flashing) is increased with each
pressing of Button S2. To move the digits quickly, keep the Button pressed.
5. After all adjustments are completed, press Button S3 to return to the NORMAL TIME display.
LIGH
S1
ST/STP
■ H OW T O S E T N O R M A L T I M E
S3
S2
■ H OW TO D I S P L AY M O N T H / DAT E
SECONDS
P
S1
RESET
MINUTES
HOURS
P
1. From NORMAL TIME display, press and hold Button S1 to show the MONTH/DATE display.
2. While keeping Button S1 pressed, press Button
S2 to switch to the DATE/MONTH display.
3. Press Button S2 again to switch back to the
MONTH/DATE display.
* The display format in either DATE/MONTH indication or in MONTH/DATE indication can be
selected alternately by pressing Button S2.
AFTERNOON
Mode
AFTERNOON
RESET
S4
ALARM
SIGNAL
S3
ST/STP
CHIME
SIGNAL
Light
PRESS
ST/STP
DAY O F
THE WEEK
S2
OR
12 HOUR
MOD
E
■ D I S P L AY A N D B U T TO N O P E R AT I O N
S1
PRESS AND HOLD
MOD
E
1. Digital time displays: Hour, Minute, Second,
Month, Date and day of the week.
2. Daily alarm: The alarm can be set to sound at
the designated time on a 24-hour basis.
3. Chime: The chime can be set to sound every
hour on the hour with a single beep.
4. Stopwatch: The stopwatch can measure up
to 23 hour s 59 minutes and 59 seconds in
1/100-second increments for the first first 39
minutes and 59. 99 seconds, and in 1-second
increments thereafter. Lap time measurement
is available.
5. I l l u m i n a t i n g l i g h t : T h e b u i l t - i n e l e c t r o luminescent (EL) backlight illuminates the
display for easy viewing in darkness.
■ H O W T O S W I T C H 1 2 - H O U R / 2 4 - H O U R
F O R M AT
LIGH
T
■ C H A R AC T E R I S T I C S
NORMAL TIME
E
S3
RESET
RESET
E
PRESS
S1
PRESS
LIGH
T
ST/STP
S1
P
E
MOD
ST/STP
T
S2
PRESS
S2
LIGH
PRESS
RESET
MONTH
SETTING
SECONDS
SETTING
E
MOD
RESET
P
DATE
SETTING
PRESS
PRESS
MINUTES
SETTING
S2
RESET
1. From NORMAL TIME display, press and hold Button S3 for 3 seconds to show the ALARM TIME
display. The hour digits start flashing.
2.Press Button S2 to set hour digits.
3.Press Button S1 to move on to minutes setting.
4.Press Button S2 to set minute digits setting.
5. After all settings are completed, press Button
S3 to return to the NORMAL TIME display.
Engagement/Disengagement of ALARM &
CHIME
* Press and hold Button S2, and then press Button S1, the ALARM and CHIME can be engaged or disengaged in the order below.
* The ALARM signal and/or CHIME signal appear
or disappear on the display accordingly.
S2
NORMAL TIME
CHIME
SIGNAL
PRESS
S1
LIGH
T
P
S1
E
S2
E
MOD
RESET
MOD
P
ALARM
SIGNAL
ST/STP
ST/STP
PRESS
S1
S2
RESET
E
MOD
RESET
P
S2
S1
PRESS
T
T
P
MOD
ST/STP
LIGH
T
ST/STP
S1
PRESS
HOURS
PRESS SETTING
LIGH
RESET
T
T
LIGH
LIGH
S3
PRESS
LIGH
MINUTES
SETTING
ALARM
PRESS
S2
ALARM MODE
E
E
E
MOD
MOD
PRESS
DAY OF WEEK
SETTING
LIGH
T
ST/STP
P
P
MOD
ST/STP
ST/STP
P
RESET
P
PRESS
AND
HOLD
S3
MOD
PRESS
ALARM &
PRESS
PRESS
S1
ALARM
S1
LIGHT
LIGHT
ST/STP
RESET
P
CHIME
OFF
P
MODE
CHIME ON
RESET
CHIME OFF
CHIME
ON
PRESS
PRESS AND
HOLD
S1
RESET
P
MODE
S2
PRESS
ST/STP
PRESS AND
HOLD
LIGHT
E
MOD
Note:
1. If your watch is not equipped with Button S4,
this function is not available.
2. The backlight of the watch employs an electro-luminescent (EL) light, which tends to lose
illuminating power after very long use.
3. The illumination provided by backlight may be
hard to see when viewed under direct sunlight.
* When the illuminating light becomes dim, replace the batteries with new ones.
LIGHT
PRESS
ST/STP
LIGH
T
S2
MODE
P
ST/STP
S4
PRESS AND
HOLD
P
MODE
■ H OW TO U S E E L B AC K L I G H T
ST/STP
CHIME ON
ALARM ON
* In NORMAL TIME display, press Button S4 to
illuminate the display for approximately 3 seconds.
PRESS
S2
RESET
S2
PRESS
AND
HOLD
CHIME ON
RESET
HOURS
SETTING
ALARM & CHIME
S1
S2
ALARM
OFF
OFF
How to stop the alarm while sounding
The alarm sounds for 20 seconds at the designated time. To stop it manually while sounding, press
Button S2.
■ H OW TO U S E S TO P WAT C H
■ B AT T E R Y C H A N G E
* From NORMAL TIME display, press Button S3 to
go to the STOPWATCH mode.
1. The miniature batter y SEIKO CR1220, Maxell
CR1220 or SONY CR1220, which powers your
watch, should last approximately 2 years. However, because it is inserted at the factory, the
actual life of the battery once in your possession may be less than 2 years.
2. Be sure to replace the battery to prevent any
possible malfunction as soon as it runs down.
3. To replace the battery we recommend taking
the watch to a local watch repair shop.
S TO P WAT C H M O D E
T
LIGH
Reset/Lap
MOD
E
RESET
P
S3
S1
ST/STP
Mode
Start/Stop
Note:
If the alarm is used for more than 20 seconds a
day and/or the illuminating light for more than
8 seconds a day, the battery life may be less
than the specified period.
S2
HOURS MINUTES SECONDS
Standard Measurement
1.Press Button S1 to start and stop the STOPWATCH.
2.Press Button S2 to reset the STOPWATCH to
"0:00:00."
S1
S2
Start
Stop
Reset
PRESS
LIGHT
RESET
MODE
MODE
RESET
S3
P
S TO P WAT C H
• WATER RESISTANT
PRESS
START
S1
Condition Accidental
of use
contact Swimming
with water, and taking
such as
Indication
a shower
splashes
on the dial/
and
rain
case back
RESET
LIGHT
MODE
RESET
P
S2
S3
ST/STP
PRESS
PRESS
No
Indication
WAT E R R E S I S TA N T
WAT E R R E S I S TA N T
( 5 0 M / 5 BA R )
WAT E R R E S I S TA N T
STOP
LIGHT
ST/STP
PRESS
S1
MODE
RESET
P
CAUTION
Do not expose the old battery to fire
or recharge it. Keep it at a place beyond the reach of chil­dren. If a child
swallows it, consult a doctor immediately.
ST/STP
ST/STP
LIGHT
NORMAL TIME
RETURN
This watch contains precise electronic components. Never attempt to open the case or remove the back cover.
• BATTERY
S1
P
■ CA R E O F YO U R L O R U S WAT C H
(100M/10 BAR
or above
Stopwatch display
(
Skin
diving
Scuba
diving
NO
NO
NO
NO
YES
NO
NO
NO
YES
YES
NO
NO
YES
YES
YES
NO
ST/STP
ST/STP
LIGHT
MODE
MODE
RESET
P
RESET
LIGHT
* If your watch is 200 M/20 BAR, 100 M/10 BAR or
50 M/5 BAR water resistant, it is so indicated on
the dial/case back.
• Do not operate the buttons when the watch is
wet.
1/100 SECONDS
SECONDS
• If the watch is exposed to salt water, rinse it in
After 39 minutes and
For the first 39 minutes
fresh water and then wipe it thoroughly dry.
and 59. 99 seconds , 59. 99 seconds, hours,
minutes, and seconds • Should you find any water or condensation inminutes, seconds, and
side the watch, immediately have it checked.
are displayed.
1/100 seconds are
Water can corrode electric parts inside the
displayed.
case.
P
Lap Time Measurement
S1
S2
S2
Start
Lap 1
Lap 2
S1
S2
S2
Stop Last lap Reset
PRESS
LIGHT
ST/STP
MODE
RESET
S3
P
MODE
NORMAL TIME
RESET
LIGHT
ST/STP
P
S TO P WAT C H
PRESS
RETURN
S3
RESET
PRESS
LIGHT
RESET
LIGHT
ST/STP
MODE
MODE
RESET
P
PRESS
S2
PRESS
S1
S2
ST/STP
P
START
RECALL LAP
MEMORY
LAP
PRESS
STOP
LIGHT
ST/STP
MODE
RESET
ST/STP
LIGHT
S2
P
Caution:
Leather straps are not water resistant except so
indicated, even if the watch head is water resistant.
• ALLERGIC REACTION
Because the case and band touch the skin directly, it is important to clean them regularly. If
not, shirt sleeves may be stained and those with
delicate skin may develop a rash. Please wear
the watch with some play to avoid any possible
allergic reaction. If you develop a rash on your
wrist, stop wearing and consult a physician.
• MAGNETISM
Your watch will be adversely affected by strong
magnetism. Keep it away from close contact with
magnetic objects. • SHOCKS AND VIBRATIONS
Your watch may be worn for normal sports activities, but be careful not to drop it or hit it on hard
surfaces.
• TEMPERATURE
Your watch is preadjusted so that constant accuracy may be insured at normal tem­pera­ture.
• CLEANING
Use only a soft cloth and clean water for cleaning
your watch. Never use chemicals, as the waterproof gasket will corrode.
MODE
RESET
P
PRESS
S1
LAP
* While the stopwatch is measuring, press Button S2 button to take lap times.
* Measurement and release of lap times can
be repeated by pressing Button S2.
HOW TO RECALL THE LAP TIME DATA
Lap time data obtained in the STOPWATCH
mode can be recalled after measurement.
After stopping the stopwatch, press Button S2
to view the recorded lap times.
The lap times will be displayed one after another with each press of the button.
*Press Button S3 to return to the NORMAL TIME
display.
■ S E R V I C E
When your LORUS watch requires repair or servicing, please see the enclosed WARRANTY/GUARANTEE.
Printed in China