User & Programming Guide We thank you for your purchase of E-Motion™ automated shades from Elite Window Fashions™. Your shades have been custom programmed by our factory to automatically stop at the top and bottom of your windows. Please consult this guide for proper shade operation. Programming instructions can be found on pg 2 of this sheet and, if necessary, step-by-step instructions on how to reprogram and adjust the shade limits. 5 Channel Handheld Remote Operating Instructions (available in black or white finish) Channel LED Lights 1 2 3 4 Raise Shade: Press and hold Lower Shade: Press and hold 5 Stop Shade: Press Up Stop C L Change Channels Limit Confirm Front View button for 1-2 seconds. button while shade is in motion. Tilt Shade (High-Lite® & Sheer Horizontal Shades only): Press and release or button. Transmitter Model: BF-305W Freq: 433.92MHz Battery: CR2430 Down button for 1-2 seconds. Change Channels: Press or arrows to change channels. The numbered LED lights at the top of the remote indicate the current channel. When all LED lights are on, the remote will operate all shades. Rear View 1 or 2 Channel Wall Remote (available in black or white finish, 2 Channel Wall Remote Shown) Operating Instructions Raise Shade: Press and hold Lower Shade: Press and hold LED Light Stop Shade: Press Up Stop button for 1-2 seconds. button for 1-2 seconds. button while shade is in motion. Tilt Shade (High-Lite® & Sheer Horizontal Shades only): Press and release or button. Down Channel 1 Buttons Channel 2 Buttons Confirm Button 2 Channel Wall Remote: Left-side control buttons = Channel 1 Right-side control buttons = Channel 2 Limit Button (cover plate removed) Pg. 1 Programming/Adding a Shade to Your Handheld or Wall Remote Control 1) Press and hold the red button on motor for 1-2 seconds until the shade jogs. 2) For handheld remotes use the channel buttons to select the desired channel to which you want to program the motor. For wall remotes press any button on the left side to select channel 1 or any button on the right to select channel 2. 3) Using a paperclip or pen, press the Confirm button on your handheld or wall remote. The shade will jog to confirm successful programming. Repeat steps 1-3 when programming new shades or if adding existing shades to a new channel or remote. Removing a Shade From Your Handheld or Wall Remote Control This will remove the shade from all channels and remotes to which it was assigned. But don’t worry, we know what you’re thinking....... the upper and lower limits will remain in the motor’s memory. 1) Press and hold the red button on the motor for 4-5 seconds (motor will cycle through two distinct sets of jogs). The motor has now been removed from all channels and remotes. Setting or Adjusting Shade Limit Positions IMPORTANT NOTE: By setting or adjusting new shade limit positions, you will be temporarily erasing both the upper and lower stop positions. As a result, the shade will NOT stop on its own during this process and damage to your shade may occur as a result of not following or not completing these instructions. ALL STEPS must be completed to properly set new limits. Before You Begin: Only one shade can have its limits adjusted at one time. If the shade needing adjustment is the only one assigned to the channel, please continue below. If the shade is on a channel that also controls other shades: a) Disconnect the power (battery wand or DC transformer) from all other shades or b) Remove the programming of all other shades from the channel and remote (see section above). 1) Select the channel of the shade you want to adjust: - For handheld remotes use the channel buttons to select the desired channel to which you want to program the motor. - For wall remotes press any button on the left side to select channel 1 or any button on the right to select channel 2. 2) Press and hold the Limit button on your handheld or wall remote for 5-6 seconds until the motor jogs. 3) Press “down” button to send shade down. WARNING: MOTOR WILL NOT STOP ON ITS OWN! 4) Press “stop” button once the shade reaches desired position at the window sill. Once stopped, the shade can be finely adjusted in small increments by pressing “up” or “down” buttons. 5) When satisfied, use a pen or paperclip to press “Confirm” to set the lower limit stop position. CONTINUE TO STEP 6. 6) Press “up” button to send shade up. WARNING: MOTOR WILL NOT STOP ON ITS OWN! 7) Press “stop” button when shade is 2” - 3” from top to prevent damage to the shade. Once stopped, shade can be finely adjusted in small increments by pressing “up” or “down” buttons. 8) When satisfied, use a pen or paperclip to press “Confirm” to set the new upper limit stop position. follow us on: www.elitewf.com Copyright © 2015 Elite Window Fashions™ | 1 Applewood Crescent, Unit 1 Concord, Ontario, Canada L4K 4K1 Tel: 1-800-387-3566 | Fax: 1-800-665-3672 | email: customerservice@elitewf.com Pg. 2