CCTV
6. Mounting the Camera
Fix the mount to the casing in the correct area before attaching the bracket
(not supplied). See the diagram below illustrating how the mount for the
bracket can be fixed to either the top or the bottom of the camera:
Bottom Mount (supplied fixed)
Top Mount
Note: Should you wish to use this camera externally you will require an Xvision external housing.
CCTV
TECHNICAL SUPPORT:
For Technical Support for any Xvision product please contact your
local distributor.
LIMITED WARRANTY:
This product is supplied with a 2 Year warranty. The Warranty excludes
products that have been misused, (including accidental damage) and
damage caused by normal wear and tear. In the unlikely event that you
encounter a problem with this product, it should be returned to the place
of purchase.
Model: PCC225-2
Colour 480 TVL CCTV Camera
Specifications
Model:
PCC225-2
Picture Type:
Colour
Image Sensor:
Sony 1/3” Super HAD CCD
DSP:
Resolution:
Lens Viewing Angle:
Minimum Illumination:
Audio:
Xvision IXC1
480TVL
Various (CS/C Mount)
0.1 Lux
Yes
Operating Voltage:
12V DC 200mA
Suggested Power Supply:
12V DC 300mA
Mounting:
Weatherproofing:
Dimensions:
Wall/Ceiling (bracket required)
Yes (using optional housing)
(WxHxD) 63x59x118mm
Before you begin
Manufactured exclusively for Xvision - www.x-vision.co.uk
UK/Europe
Xvision Group (UK)
Unit 2, Valley Point,
Beddington Farm Road,
Croydon
Surrey. CR0 4WP
Email: sales@x-vision.co.uk
Middle East
Burjuman Tower,
18th Floor
PO Box 121828
Dubai 43659
United Arab Emirates
Email: mesales@x-vision.co.uk
Far East
Kyoung Am Building
157-27 Samsung-dong
Kangnam-ku
135 090 Seoul
Korea
Email: globalsales@x-vision.co.uk
North America
100 Park Avenue
New York City,
New York
10017
United States
Email: usasales@x-vision.co.uk
zz Please unpack the box carefully and identify that all the parts are present.
zz Do not open the camera housing. This will void the warranty and break the
warranty seal inside the camera.
zz Make sure you use only the recommended power supply. Damage caused to
the camera by incorrect voltage or wiring is not covered by the warranty.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT OPEN OR REMOVE
COVER OR BACK. NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE.
Model:
PCC225-2
Colour 480 TVL CCTV Camera
Thank you for purchasing this Xvision camera. Before operating this
product, please read this instruction manual carefully.
4. Connections
5. Operating Instructions
1. Product Description
The PCC225-2 is a high quality Colour Body Camera with a High
Resolution Sony 1/3” Super HAD CCD and Xvision IXC1 DSP for great
colour balance, resulting in a naturally vibrant image. The CCTV
Camera is designed for use in high risk applications where high
resolution surveillance is required. The camera is supplied without lens
and mounting equipment, a wide range of accessories are available for
use with the camera, including lenses, brackets and housings.
On the rear of the units you will find the following:
VIDEO OUT - Allows you to connect BNC plug to enable Video.
2. Features
AUDIO OUT - Allows you to connect a Phono socket to enable Audio.
zzSony 1/3” Super HAD CCD image sensor for 480 TVL resolution images
zzCS/C Mount connection for use with a variety of lenses
zz0.1 lux low light sensitivity
zzThe camera can be mounted internally or externally using optional
brackets and housings.
3. Contents
Lens Mount Dial
Rear of PCC225-2
AUTO IRIS - Allows you to connect an Auto Iris lens.
VIDEO or DC - Match this setting to the type of Auto Iris lens.
AWB (AUTO WHITE BALANCE) or OFF - Set this to AWB when the
camera image requires automatic adjustment of the colour temperature
to match the type of light available, so that white and other colours
appear as natural as possible.
1.Remove the cap from the top of the Lens mount.
2.Screw the lens into the lens mount.
3.Connect the video output to the monitor or other video device through a
75 Ohms type coaxial cable.
4.Connect the power source with a DC jack. The LED indicator will light up
5.Once the picture appears on the monitor, adjust the focus and iris of the
lens to obtain the best picture.
6.If the focus is still not clear, adjust the camera and lens as follows:
-- Aim the camera at a subject more than 20 metres away.
-- Turn the lens and the lens mount dial until the subject is in focus & the picture is clear.
-- Tighten the lens mount screw.
To back focus the camera
Loosen the Lens Mount screw located on the side of the camera (using
a screwdriver) and then turn the Lens Mount dial as required to adjust
the back focus as shown in the diagram. Tighten the screw after any
adjustments have been made.
Lens Mount
Screw
AGC (AUTOMATIC GAIN CONTROL) or OFF - Set to AGC to apply
Automatic Gain Control which will brighten the picture when in a dark
environment.
PCC225-2 Camera
Lens Mount
Dial
EE (AUTO ELECTRONIC EXPOSURE) or AI (AUTO IRIS)- Set this to
AI when using an Auto Iris lens, or to EE when using a standard lens.
Lens Mount
screw
Mount for
bracket*
* The camera will be supplied with the Mount for the bracket pre-attached to the base of the camera.
The camera bracket (not supplied) can be attached to the top of the camera by adjusting the mount.
See ‘Mounting the Camera’ for more information.
BLC (BACK LIGHT COMPENSATION) or ON - Set to BLC when
viewing objects against a very bright background. This setting will
brighten the whole scene so the object can be seen clearly.
LEVEL - When using DC Auto Iris lenses this adjustment screw allows you
to alter the video level (brightness of the image).
PCC225-2 Camera Front
Installation of the Auto Iris Connector
Set the pin assignment as shown:
Pin 1:
Pin 2:
Pin 3:
Pin 4:
VIDEO Drive
D.C. Drive
12V DC
No Use
Video Signal
Video Drive
Damp Damp +
Driver +
Driver -