SUPER
DIGITAL PANEL METER
www
STORE
YOUR BEST ONLINE STORE
Operation Manual
Thank you for purchasing our product !
2-Year Limited Warranty SUPERwwwSTORE warrants your newly purchased product against defects in
material and workmanship existing at the time of manufacture for a period of two years from the date of purchase.
Warranty Registration is not necessary to obtain the applicable warranty on the product. The date of purchase will
be used to determine the warranty period when warranty service is requested.
It is important to read the Setup Guide before installing or commissioning this instrument
as it contains important information relating to safety and EMC.
Please verify the panel cutout dimensions and mount according to instructions.
SAFETY CONSIDERATIONS
Unpacking and Inspection
Your instrument has been carefully tested and inspected prior to shipment. Unpack
the instrument and inspect for obvious shipping damage. Please do not attempt to
install or operate the unit if damage is found.
This instrument is a panel mount device protected in accordance with Class I of EN
61010. Installation of this instrument should be done by Qualified personnel. In order
to ensure safe operation, the following instructions should be followed.
This instrument has no power-on switch; it will be in operation as soon as power is connected.
Do not make signal wiring changes or connections when power is applied to the instrument.
Make signal connections before power is applied and, if reconnection is required, disconnect
the power before such wiring is attempted. Do not connect more than one meter to the same
power supply if the meters cannot use the same signal ground.
Do not exceed voltage rating stated on the specifications.
Always disconnect power before changing signal and power connections.
Do not use this instrument on a work bench without its case for safety reasons.
Do not operate this instrument in flammable or explosive atmospheres.
Do not expose this instrument to rain or moisture.
Whenever EMC is an issue, always use shielded cables.
Instrument which will not be installed immediately should be stored in a clean, dry location.
WARNING:
The use of this instrument in a manner other than specified may impair the
protection of the instrument and subject the user to hazard.
Careful use of the instrument will provide years of reliable service.
Please consult your licensed electrician/electrical engineer for professional advice before installation.
At the end of its life cycle, dispose of this product in accordance with local and national disposal regulations.
The information contained in this document is believed to be correct but SUPERwwwSTORE DigitalWorld
accepts no liability for any errors it contains, and reserves the right to alter specifications without notice.
© Copyright 2009 SUPERwwwSTORE DigitalWorld. All rights reserved. This document may not be copied,
photocopied, reproduced, translated, or reduced to any electronic medium or machine-readable form,
in whole or in part, without prior written consent of SUPERwwwSTORE DigitalWorld.
-- 1 --
SUPERwwwSTORE
- Digital DC Voltage & Current Panel Meters (5035)
KEY FEATURES:
-Dual-Slope integration A/D converter system
-Ultra-bright 7-Segment Backlight LCD display
-12.7 mm (0.5 inches) digit height
-Blue/red/green/white/orange colour displays available
-The switch can be used to turn the backlight ON/OFF.
-Can be powered from same source (6~24Vdc) being measured
-Polarity : Automatic, "-" displayed
-Automatic zero reading for 0V input
-High input impedance
-Low cost high accuracy
-Input signal and power supply can have common ground
-Can be re-calibrated by adjusting the calibration potentiometer
-4-Pin connection cable (300 mm) included
-Easy to install (DIY), snap-in/mount in panel
-Ideal for auto, boat, industrial & domestic uses
5035 LCD Display Digital Panel Meter
Please check to make sure that the type of meter
you have received is exactly the SAME as
shown in the picture above.
OPERATION SPECIFICATION:
Power Source … … … … … … … .. 5V to 24V DC powered
Power Consumption … … … … … <50 mA
Maximum Count........................ ±1999 (3-1/2 digits)
Operating Temperature… … … … 0 to +60°C (32 to 140°F)
Storage Temperature … … … … -20 to +80°C (-4 to 176°F)
Humidity… … … … … … … … … … . Below 90% RH
Over Range Indication… … … … .. "1" or "-1" shown in the display
Weight … … … … … … … … … … . 47.2 g
Panel Cutout … … … … … … … … 71 x 39 mm
Meter Dimensions … … … … … … 79(W) x 43(H) x 25(D) mm
RANGES AND ELECTRICAL SPECIFICATION:
DC VOLTAGE MODELS
Measuring Range
Accuracy
Resolution
4-pin Pigtail Connector included
Input Impedance
1 mV
1 M ohm
0 ~ 1.999 V
0.001 V
1 M ohm
0 ~ 19.99 V
0.01 V
1 M ohm
0.1 V
1 M ohm
0.1 V
1 M ohm
0 ~ 500 V
1V
10 M ohm
0 ~ 1000 V
1V
10 M ohm
0 ~ 1999 V
1V
10 M ohm
0 ~ 1999 mV
0 ~ 50.0 V
0 ~ 199.9 V
±0.2%
DC CURRENT MODELS
Measuring Range
Accuracy
0 ~ 1999 mA
Resolution
Shunt *
1 mA
Built-in
0.001 A
Built-in
0.01 A
Built-in
0.01 A
10A 75mV
0.01 A
20A 75mV
0 ~ 50.0 A
0.1 A
50A 75mV
0 ~ 100.0 A
0.1 A
100A 75mV
0 ~ 199.9 A
0.1 A
200A 75mV
0 ~ 1.999 A
0 ~ 5.00 A
0 ~ 10.00 A
0 ~ 19.99 A
±0.2%
Sample Rate
Max. Input Signal
2.5 Reading/sec.
<5 V
<5 V
<25 V
<100 V
<250 V
<1000 V
<1500 V
<2200 V
Sample Rate
Max. Input Signal
<3000 mA
<3 A
2.5 Reading/sec.
<6 A
<12 A
<25 A
<60 A
<120 A
<220 A
* An appropriate 75mV Shunt (sold at our Store) must be used for an ammeter (10 amps or over) to read amps/current.
-- 2 --
SUPERwwwSTORE
- Digital Panel Meter Installation and Wiring Diagram
DIMENSIONS All dimensions in mm (inches)
SIDE VIEW
20 (0.8)
a = 2 (0.08)
b = 23 (0.9)
71 (2.8)
CONNECTOR WIRING
Calibration
Potentiometer
v
v
IN
Power Source
+
_ Power Source (6V~24V DC)
_ Volts/Amps to be measured
IN
+- -
+
43 (1.7)
45 (1.8)
PANEL CUTOUT SIZE
b
39 (1.5)
a
79 (3.1)
+ Volts/Amps to be measured
REAR VIEW
CAUTION: Damage to the unit may occur if the power source/signal polarity is reversed OR power source >24Vdc is apllied.
WIRING
INFORMATION
VOLTMETER … … To be connected in PARALLEL in the circuit
… … … To be connected in SERIES in the circuit
AMMETER
…
…
… … … To be used with Ammeter (10A or over) & must be in LOW side (nearest to -NEGATIVE terminal)
SHUNT
LOAD … … … … … … Any device such as a lamp, horn, wiper motor,alarm,...that consumes electricity. And Load
must be used & activated when measuring amps/current.
A) VOLTMETER
Powered by the same source (6~24Vdc)
Powered by a separate supply source
LOAD
Signal
Input
LOAD
+
+
_
_
_
_
v
Voltmeter
_
Signal Input
IN
_
-
_
_
_
_
+
_
_
+
v
Voltmeter
_
+
_ v
_ IvN
+ IN
_
IN
-v
_
-
_
+
+
-v
+
6~24V DC
6~24V DC
+
_v
_ IvN
+ IN
B) AMP METER / AMMETER
Powered by the same source (6~24Vdc)
LOAD
LOAD
SHUNT
+
SHUNT
_
_
Signal Input
_
_
A
Ammeter
_
_
v
IN
-
_
_
_
6~24 V DC
__ _
_
+
_
_
_
_ +_
+
_ v
_ IvN
+ IN
_
_
_
_
+
_
_
_
_
+
_
+
A
Ammeter
6~24V DC
_
_
+
v
IN
-
+
_v
_ IvN
+ IN
Signal Input
Powered by a separate supply source
C) VOLTMETER + AMMETER
Powered by the same source (6~24Vdc)
LOAD
SHUNT
LOAD
_
_
v
IN
-
v
+
_ v
_ IvN
+ IN
_
+
_
_
_
_
+
SHUNT
+
Signal Input
_
_
_
_ _
A
Ammeter
+
_
_
_
6~24V
_ DC
v
IN
-
_
_
_
6~24 V DC
_ _ _
_
+
_
__
_ +_
+
_ v
_ IvN
+ IN
_
_
_
_
+
_
_
_
_
_
+
+
v
+
_v
_ IvN
+ IN
_
_
_
_
+
v
IN
-
+
_
A
Ammeter
6~24V DC
_
_
+
v
IN
-
+
_v
_ IvN
+ IN
Signal Input
Powered by separate supply sources
_
_
_
_
Voltmeter
Voltmeter
Please consult your licensed electrician/electrical engineer for professional advice before installation.
-- 3 --