SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005
NATIONAL TECHNICAL SYSTEMS (NTS)
Plano Division
1701 E Plano Pkwy Suite 150
Plano, Texas 75074
Kimberly Zavala
Phone: 972 509 2566
Kimberly.Zavala@ntscorp.com
ELECTRICAL (EMC)
Valid to: December 31, 2017
Certificate Number: 0214.19
In recognition of the successful completion of the A2LA evaluation process (including an assessment of the
organization’s compliance with A2LA’s EPA ENERGY STAR Accreditation Program Requirements1),
accreditation is granted to this laboratory to perform the following tests:
Test Technology:
Emissions
Radiated Emissions
(3 m Semi Anechoic
Chamber,
10 m Semi Anechoic
Chamber)
Test Capabilities:
Test Method(s)2:
60 Hz to 40 GHz
Code of Federal Regulation (CFR) 47,
FCC Part 15 (Subpart B) using ANSI C63.4: 2003,
ANSI C63.4:2009 and ANSI C63.4:2014;
FCC Part 18 (using MP5)
CISPR 22; EN 55022; KN 22;
AS/NZS CISPR 22:2009+A1 :2010;
CISPR 32; EN 55032; CISPR 11; EN 55011;
AS/NZS CISPR 11:2011; KN 11;
VCCI V-3 (up to 6 GHz); CNS 13438 (up to 6 GHz);
TCVN 7189 (2009); CISPR 25; CISPR 12; ICES-003;
EN 13309; ISO 13766; ISO 11451-2; KN 32
MIL-PRF-28800F; MIL-STD-461 B-F
(Methods RE101, RE102, RE103); MIL-STD-462;
RTCA/DO-160 C-G (Sections 15, 21)
Conducted Emissions
30 Hz to 100 MHz
Code of Federal Regulation (CFR) 47,
FCC Part 15 (Subpart B) using ANSI C63.4:2003,
ANSI C63.4:2009 and ANSI C63.4:2014;
FCC Part 18 (using MP5)
CISPR 22; EN 55022; AS/NZS CISPR 22; KN 22;
CISPR 32; EN 55032; CISPR 11; EN 55011;
AS/NZS CISPR 11; KN 11; VCCI V-3; CNS 13438;
TCVN 7189 (2009); CISPR 25; ICES-003; ISO 13766
MIL-STD-461 B-F (Methods CE101, CE102);
MIL-STD-462; MIL-PRF-28800F;
RTCA/DO-160 C-G (Section 21)
(A2LA Cert. No. 0214.19) 01/15/2016
Page 1 of 6
Test Technology:
Test Capabilities:
Emissions (cont’d)
Current Harmonics
IEC/EN 61000-3-2; AS/NZS 61000.3.2
IEC/EN 61000-3-3; AS/NZS 61000.3.3
Flicker
Immunity
Electrostatic Discharge
(ESD)
Radiated Immunity
Test Method(s)2:
15 kV air,
8 kV contact
EN/IEC/KN 61000-4-2; MIL-PRF-28800F;
RTCA/DO-160 C-G (Section 25); ISO 10605; ISO 13766
10 kHz to 40 GHz
EN/IEC/KN 61000-4-3;
MIL-STD-461 B-F (Methods RS101, RS103);
MIL-STD-462; MIL-PRF-28800F;
DoD-STD-1399, Section 300A and B;
IEEE P1613; MIL-STD 1275;
IEC/EN 55104; ISO 13766; EN 13309; ISO 11451-2;
GR-1089-CORE; ISO 11452-2;
RTCA/DO-160 C-G (Section 20)
Electrical Fast
Transient/Burst
EN/IEC/KN 61000-4-4;
MIL-PRF-28800F;
IEEE P1613
Surge
EN/IEC/KN 61000-4-5;
IEEE P1613; IEEE 37.90.1;
K20; K21; RTCA/DO-160 C-G (Section 22)
Conducted Immunity
10 kHz to 400MHz
EN/IEC/KN 61000-4-6; MIL-STD-1399;
MIL-STD-461 B-F (Methods CS101, CS102, CS103,
CS104, CS105, CS109, CS114, CS115, CS116);
MIL-STD-462; MIL-PRF-28800F; RTCA/DO-160C-G
(Section 16, 17, 18,19, 20, 22)
Power Frequency
Magnetic Field Immunity
EN/IEC/KN 61000-4-8
Voltage Dips, Short
Interruptions and Line
Voltage Variations
EN/IEC/KN 61000-4-11
DC Power Transients
MIL-STD-704 A-F; EN 300 132; ANSI T1.315;
ATT-TP-76200; ATT-TP-76450
Lightning/AC Power
Cross
GR-1089-CORE; MIL-STD-704 A-F
Steady State Power
Induction
GR-1089-CORE; ETSI EN 300 386;
AT&T-TP76200
DC Potential
GR-1089-CORE; AT&T-TP76200
Electrical Safety
GR 1089-CORE; AT&T-TP76200
Bonding & Grounding
GR 1089-CORE; AT&T-TP76200
(A2LA Cert. No. 0214.19) 01/15/2016
Page 2 of 6
Test Technology:
Test Capabilities:
Immunity (Cont’d)
Insulation Resistance
Test Method(s)2:
GR-49-CORE; GR-937-CORE;
GR-950-CORE; GR-2916-CORE
Energy Efficiency for
Telecom. Equipment
ATIS-0600015; VZ.TPR.9205;
IEEE P1613
Heat Dissipation
GR-63-CORE; ATIS-0600010
DC Power Port
GR-1089-CORE (Section 10)
Wireless
EU
ETSI 300 200-2; ETSI EN 300 328; ETSI EN 300 330-2;
ETSI EN 300 440-2; ETSI EN 301 893
Industry Canada Radio
Standards Specifications
(RSS)
RSS-GEN; RSS-119; RSS-123; RSS-125; RSS-127;
RSS-130; RSS-131; RSS-132; RSS-133; RSS-139;
RSS-210; RSS-310
Intentional and
Unintentional Radiators
to FCC Regulations
(Up to 40GHz) Excluding
HAC (Supports TCB
Scopes A1-A4 and B1-B4)
47 CFR (FCC Rules) Part 15.A;
47 CFR (FCC Rules) Part 15.B,
using ANSI C63.10:2009 and C63.10:2013;
47 CFR (FCC Rules) Part 15.C,
using ANSI C63.10:2009 and C63.10:2013;
47 CFR (FCC Rules) Part 15.E,
using ANSI C63.10:2009 and C63.10:2013;
47 CFR (FCC Rules) Parts 22 (Cellular and Non-Cellular),
24, 27, 74, 80, 87, 90, 95, and 101,
using ANSI/TIA 603-C-2004
Energy Management
American National
Standard for Electric
Meters Code for
Electricity Metering /
Electricicy Meters – 0.2
and 0.5 Accuracy Classes
ENERGY STAR Testing1
Office Equipment
Computers
ANSI C12.1/C12.20
(excluding tests 20, 21, 36, 37, and 38)
ENERGY STAR Test Method for Computers (Oct-2014);
ENERGY STAR Program Requirements Product
Specification for Computers (Ver. 6.1, Oct-2014)
Enterprise Servers
ENERGY STAR Program Requirements Product
Specification for Computer servers (Ver. 2.0, Oct-2013);
Standard Performance Evaluation Corporation (SPEC)
most current Server Efficiency Rating Tool (SERT)
Imaging Equipment
ENERGY STAR Imaging Equipment Test Method
(Rev. Oct-2014); ENERGY STAR Program Requirements,
Product Specification for Imaging Equipment
(Ver. 2.0 Oct-2014)
(A2LA Cert. No. 0214.19) 01/15/2016
Page 3 of 6
Test Technology:
Test Capabilities:
Test Method(s)2:
Generic/Product Family
Standards and Industry
Standards
IEC/EN 61000-6-1; IEC/EN/KN 61000-6-2;
IEC/EN 61000-6-3; IEC/EN/KN 61000-6-4;
CISPR 24; EN 55024; KN 24; EN 61326;
ETSI EN 300 386; GR-1089-CORE;
ATT-TP-76200; IEC/EN 60601-1-2; EN 50082;
AS/NZS 61000.6.3; AS/NZS 61000.6.4;
EN 61326; IEC 60601-1-2;
CISPR 14-1; KN 14-1; CISPR 14-2; KN 14-2;
EN 55014-2; KN 35
Hearing Aid Compatibility
CS03 Part V, Issue 9, Amendment 1, 2009;
FCC Part 68.316; FCC Part 68.317
Telecom
Analog 2 Wire
T1 1.54 Mbps
AS/CA S002:2015 Analogue Interworking and Noninterference Requirements for Customer Equipment for
Connection to the Public Switched Telephone Network;
AS/CA S003:2015 Telecommunications Technical
Standard (Requirements for Customer Access Equipment
for connection to a Telecommunications Network
CS03- Part 1 (Analog TE), Issue 9, Amendment 4, 2010;
ETSI EN 301 437 Voice Analog TE;
ETSI ES 203 021 Analog TE;
TIA 968-B Analog 2 Wire TE; HKCA 2011 (Analog TE);
PSTN 01(Analog TE, Taiwan); TBR 21 (Analog TE,
historical);
IDA TS PSTN:2011;
ETSI EN 301 437 Voice Analog TE;
Ministry of Communications Specification 023/96;
PTC 200, Requirements for Connection of Customer
Equipment to Analogue Lines;
JATE (Analog Telephone Terminals)
CS03 Part 11 (1.5M), Issue 9, Amendment 1, 2012;
TIA 968-B 1.54 Mbps TE;
HKCA 2017 (1.5M DTMF);
ID0002: DS1 Terminal Equipment Technical
Specifications;
ITU-T G 703: 2011 (Digital Interface);
JATE (1.5M)
ISDN 1.54 Mbps-PRI
CS03 Part VI (1.5 M ISDN PRI), Issue 9, Amendment 1,
2012; TBR 4 (ISDN PRI);
PTC 220, Requirements for Private Voice Networks
connected to the PSTN/ISDN
E1 2.0M
AS/ACIF S016:2015 (E1 CE);
TBR 12 (E1); TBR 13 (E1);
ITU-T G 703: 2001 (Digital Interface);
JATE (2.0M);
ITU-T G 823: 2000 (E1 Jitter and Wander)
(A2LA Cert. No. 0214.19) 01/15/2016
Page 4 of 6
Test Technology:
Test Capabilities:
Telecom (Cont’d)
xDSL
Product Safety
Test Method(s)2:
AS/ACIF S041:2015, Requirements for Customer
Equipment for connection to a metallic local loop interface
of a Telecommunications Network Part 2: Broadband;
AS/ACIF S043:2015, Requirements for Customer
Equipment for connection to a metallic local loop interface
of a Telecommunications Network;
CS03 Part VIII xDSL(A3 2007), Issue 9, Amendment 4,
2009; ETSI TS 101 270 VDSL;
ETSI TS 101 388 V1.3.1 (2002 ADSL);
TIA 968-B xDSL;
ITU-T G 991.2 (2003, SHDSL);
ITU-T G 991.2 (A3, 2005, SHDSL);
ITU-T G 992.1 (1999, ADSL);
ITU-T G 992.3 (2005, ADSL2);
ITU-T G 992.3 (A5, 2008, ADSL2);
ITU-T G 992.3 (2005, ADSL2+);
ITU-T G 992.5 (2005, VDSL);
ITU-T G 992.5 (A5, 2008, ADSL2+);
ITU-T G 993.1 (2004, VDSL);
ITU-T G 993.2 (2006, VDSL2)

























Insulation Resistance
Leakage Current
Temperature Rise
Dielectric Strength
Short Circuit Tests
Grounding Impedance
Overvoltage Tests
Handle Strength
Cord Anchorage
Force Test
Clearance and
Creepage Distance
Measurement
Temperature/Humidity
(Environmental
Conditioning)
Enclosure/Material
Integrity
Current/Voltage/Watts
Measurement
Impact (Steel Ball and
Impact Hammer)
Stability
Mold Stress Relief
Accessibility
Drop Tests
Overload Tests
Wallmount Test
Strain Relief
Abnormal Operations
(Induced Faults)
Marking Durability
Impulse/Lightning
Testing
(A2LA Cert. No. 0214.19) 01/15/2016
CSA C22.2 No. 61010-1; EN 61010-1;
IEC 61010-1; UL 61010-1; IEC 61010-2-101;
CSA C22.2 No. 61010-2-81; IEC 61010-2-81;
EN 61010-2-81; CSA C22.2 No. 61010-1-12;
EN 60825-1 (excluding section 9);
CSA C22.2 No. 60950-1; IEC 60950-1; EN 60950-1;
UL 60950-1; AS/NZS 60950-1:2011; IEC 60065;
CSA C22.2 No. 61010-1; EN 61010-1;
IEC 61010-1; UL 61010-1; IEC 61010-2-101;
CSA C22.2 No. 61010-2-81; IEC 61010-2-81;
EN 61010-2-81; CSA C22.2 No. 61010-1-12;
EN 60825-1 (excluding section 9);
CSA C22.2 No. 60950-1; IEC 60950-1; EN 60950-1;
UL 60950-1; AS/NZS 60950-1; IEC 60065
Page 5 of 6
1
A2LA provides accreditation to the U.S. EPA’s Conditions and Criteria for Recognition of Laboratories for the
ENERGY STAR Program by verifying an organization’s compliance to A2LA document R222 - Specific
Requirements - EPA ENERGY STAR Accreditation Program and to the related test methods listed above
Accreditation by A2LA does not infer Recognition by the EPA for ENERGY STAR testing.
Please verify this organization’s recognition status at the EPA’s website, located at
http://www.energystar.gov/index.cfm?fuseaction=recognized_bodies_list.show_RCB_search_form
2
When the date, revision or edition of a test method standard is not identified on the scope of accreditation, the
laboratory is required to be using the current version within one year of the date of publication, per part C.,
Section 1 of A2LA R101 - General Requirements-Accreditation of ISO-IEC 17025 Laboratories.
(A2LA Cert. No. 0214.19) 01/15/2016
Page 6 of 6
Accredited Laboratory
A2LA has accredited
NATIONAL TECHNICAL SYSTEMS (NTS)
Plano, TX
for technical competence in the field of
Electrical Testing
This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005
General requirements for the competence of testing and calibration laboratories. This laboratory also meets the
requirements of any additional program requirements in the Electrical field. This accreditation demonstrates technical
competence for a defined scope and the operation of a laboratory quality management system
(refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009).
Presented this 15th day of January 2016.
_______________________
Senior Director of Quality & Communications
For the Accreditation Council
Certificate Number 0214.19
Valid to December 31, 2017
For the tests to which this accreditation applies, please refer to the laboratory’s Electrical Scope of Accreditation.