3-Way or More Applications (Multi-location)
Dimmer Remotes
Cat. No. VZØØR-10, Coordinating Dimmer Remote
Cat. No. VZØØR-1L, Matching Dimmer Remote
Cat. No. VZØSR-10, Coordinating Switch Remote
Cat. No. VZØSR-1L, Matching Switch Remote
120VAC, 60Hz
PK-93393-10-00-2A
INSTALLATION INSTRUCTIONS
WARNINGS AND CAUTIONS:
WARNINGS AND CAUTIONS:
• To be installed and/or used in accordance with appropriate electrical codes and regulations.
• If you are unsure about any part of these instructions, consult a qualified electrician.
• Use only one (1) Vizia™ dimmer in a multi-location circuit with up to 9 coordinating remotes without LEDs or up to 4 matching remotes with LEDs. The remote(s)
will turn the light on at the brightness level selected at the dimmer.
• To avoid overheating and possible damage to this device and other equipment, do not install to control a receptacle, fluorescent lighting, a motor- or a transformeroperated appliance.
• Recommended minimum wall box depth is 2-1/2".
• Maximum wire length from dimmer to all installed remotes cannot exceed 300 ft (90 m).
• For Hi-lume® or Eco-10™ (EcoSeries) electronic ballast applications, use instruction sheet that comes with the dimmer for multi-location applications.
• Disconnect power at circuit breaker or fuse when servicing, installing or removing fixture.
• Vizia™ remotes are not compatible with standard 3-way or 4-way switches. They must be used with compatible Vizia™ devices for multi-location switching.
• Use this device only with copper or copper clad wire. With aluminum wire use only devices marked CO/ALR or CU/AL.
Tools needed to install your Remote:
Slotted/Phillips Screwdriver
Pliers
Cutters
Step 4b 3-Way Wiring with Coordinating Remote (no LEDs)
Application:
Step 2 cont’d
Electrical Tape
Pencil
Ruler
Strip Gage (measure
bare wire here or
use gage on back of
the dimmer)
Changing the color of your Remote:
5/8"
(1.6 cm)
Your Remote includes three color options. The Remote ships with
the White frame attached. To change color of frame, proceed as
follows:
NOTE: Use check boxes
Step 1
when Steps are completed.
WARNING: TO AVOID FIRE, SHOCK, OR DEATH;
TURN OFF POWER at circuit breaker or fuse and test
that power is off before wiring!
���
��
���
��
���
��
���
��
���
��
���
��
���
��
���
��
���
��
���
��
���
��
���
��
• Make sure that the ends of the wires from the wall box are straight
(cut if necessary).
Step 4a
Matching Remote
NOTE: If the wiring in the wall box does not resemble
any of these configurations, consult a qualified
electrician.
Terminal
Screw marked
Black (BK)
BK
WH
Dimmer
Additional
Neutral Wire
4
BK
1
2
4
Terminal
Screw marked
Yellow/Red
(YL/RD)
YL/RD RD
3
3
YL/RD RD
1
5
5
Matching Remote (no LEDs) Dimmer
2
1
1
3
2
4
5
6
3
4
5
3-Way
1. Line or Load (See important
instruction below)
2. Neutral
3. Ground
4. First Traveler – note color
5. Second Traveler – note color
NOTE: For matching remote
w/LEDs installation, the First
Traveler becomes Line Hot.
4-Way
1. First Traveler – note color
2. Second Traveler – tagged
3. Neutral
4. Ground
5. Third Traveler – note color
6. Fourth Traveler – tagged
NOTE: For matching remote
w/LEDs installation, the First
Traveler becomes Line Hot.
IMPORTANT:
For 3-Way applications, note that one of the screw terminals from
the old switch being removed will usually be a different color (Black)
or labeled Common. Tag that wire with electrical tape and identify
as the common (Line or Load) in both the dimmer wall box and
remote wall box.
For 4-Way applications, note that the old switch being removed
will have 4 screws plus a ground screw. Tag the two same color
insulated wires with electrical tape.
Step 3
Hot (Black)
WH
BK
Green
Ground
Connect wires per WIRING DIAGRAM as follows:
• Green or bare copper wire in wall box to Green terminal screw.
• Line Hot (common) wall box wire identified (tagged) when removing
old switch and First Traveler to terminal screw marked "BK" or Black
dimmer lead.
• Second Traveler wall box wire from control to remote terminal screw
marked "YL/RD" (note wire color). This traveler from the remote
must go to terminal screw marked "YL/RD" or Yellow/Red control
lead.
• Line Neutral wall box to remote terminal screw marked "WH".
3
3
4
4
YL/RD RD
5
5
Coordinating Remote (no LEDs)
not used
BK
WH
Black
RD
YL/RD
Hot (Black)
BK
Green
Ground
Green
Ground
Load
Dimmer
WIRING DIMMER (wall box with Load connection):
YL/RD
RD
Line
120VAC, 60Hz
White
WIRING DIMMER:
Connect wires per WIRING DIAGRAM as follows:
NOTE: When using the coordinating remote without LEDs, the dimmer
can be installed on either the Line or Load side of the 3-way circuit.
NOTE: Maximum wire length from dimmer to all installed remotes
cannot exceed 300 ft (90 m).
• Green or bare copper wire in wall box to Green terminal screw or
Green dimmer lead.
• Line Hot (common) wall box wire identified (tagged) when removing
old switch to dimmer terminal screw marked "BK" or Black dimmer
lead.
• First Traveler wall box wire to terminal screw marked "RD" or Red
dimmer lead (note wire color). This traveler from the dimmer must
go to the terminal screw on the remote marked "RD".
• Remove Red insulating label from terminal screw marked
"YL/RD" or Yellow/Red dimmer lead.
• Second Traveler wall box wire to terminal screw marked "YL/RD" or
Yellow/Red dimmer lead (note wire color). This traveler from the
dimmer must go to the terminal screw on the remote marked "YL/RD".
Black
YL/RD
BK
RD
YL/RD
Terminal
Screw marked
White (WH)
Wiring Dimmer (wall box with Load connection):
Additional
Neutral Wire
Black
2
BK
WH
Terminal
Screw marked
Black (BK)
1
2
White
4
YL/RD RD
4
3
1
Red
5
3
5
Terminal
Screw marked
Yellow/Red
(YL/RD)
Yellow/Red
Matching Remote (w/LEDs) Control
Hot (Black)
Line
120VAC, 60Hz
WH
BK
Green
Ground
YL/RD
White
Black
Green
Ground
Red
Black
Yellow/Red
Load
White
Neutral (White)
Connect wires per WIRING DIAGRAM as follows:
NOTE: "BK" and "RD" terminals on coordinating remote are
unused. Tighten both screws.
NOTE: Maximum wire length from control to last remote is
300 ft (90 m).
• Green or bare copper wire in wall box to Green terminal screw.
• Load wall box wire identified (tagged) when removing old switch
to First Traveler (note color as above).
• Second Traveler wall box wire (note color as above) to terminal
screw marked "YL/RD". This traveler from the remote must go to
the terminal screw marked "YL/RD" or Yellow/Red control lead.
• Remove White insulating label from terminal screw marked
"WH".
• Line Neutral wall box wire to terminal screw marked "WH".
• Proceed to Step 6.
Step 5a
WH
4-Way Wiring with Matching Remote (w/LEDs)
Application:
BK
YL/RD RD
WH
Ground
Line
120VAC, 60Hz
NOTE: Electronic Low-Voltage, Mark 10™, Quiet Fan
Speed and Electronic Switch installations only. NOTE:
Dimmer is depicted.
Terminal
Screw marked
White (WH)
BK
Black
WH
1
1
YL/RD RD
2
Green
3
4
5
3
Yellow/Red
WH
BK
not used
Green
Ground
Black
RD
not used
Load
4
5
Coordinating Remote (no LEDs)
YL/RD
Control
White
Black
Hot (Black)
Green
Ground
Red
Yellow/Red
Line
120VAC, 60Hz
White
Neutral (White)
WIRING CONTROL:
RD
YL/RD
Load
NOTE: The dimmer must be installed in a wall box that has a Load
connection. The matching remote must be installed in a wall box
with a Line Hot connection and a Neutral connection. A Neutral wire
to the matching remote needs to be added as shown.
If you are unsure about any part of these instructions, consult a
qualified electrician.
NOTE: Maximum wire length from dimmer to all installed remotes
cannot exceed 300 ft (90 m).
WIRING MATCHING REMOTE (4-Way wall box with Line
Hot connection):
Red
Terminal
Screw marked
Yellow/Red
(YL/RD)
Ground
YL/RD
White
White
2
YL/RD
YL/RD RD
Neutral (White)
Control
Coordinating Remote
BK
YL/RD RD
3-Way Wiring with Coordinating Remote (no
LEDs) for Controls with Neutral Connection
Application:
Step 4d
WIRING COORDINATING REMOTE:
Connect wires per WIRING DIAGRAM as follows:
NOTE: Maximum wire length from dimmer to last remote is
Load
300 ft (90 m).
• Green or bare copper wire in wall box to Green terminal screw.
White
• Load wall box wire identified (tagged) when removing old switch to
Neutral (White)
terminal screw marked "BK".
• First Traveler wall box wire (note color as above) to terminal screw
NOTE: The dimmer must be installed in a wall box that has a Load
marked "RD". This traveler from the remote must go to the terminal
connection. The matching remote must be installed in a wall box
screw on the dimmer marked "RD" or Red dimmer lead.
with a Line Hot connection and a Neutral connection. A Neutral wire
• Second Traveler wall box wire (note color as above) to terminal
to the matching remote needs to be added as shown.
screw marked "YL/RD". This traveler from the remote must go to
If you are unsure about any part of these instructions, consult a
the terminal screw on the dimmer marked "YL/RD" or Yellow/Red
qualified electrician.
dimmer lead.
NOTE: Maximum wire length from dimmer to all installed remotes cannot • Remote terminal screw marked "WH" should have White insulation
exceed 300 ft.
label affixed.
Wiring Matching Remote (wall box with Line Hot connection):
NOTE: If insulating label is not affixed to terminal screw marked
Connect wires per WIRING DIAGRAM as follows:
"WH", use electrical tape to cover.
• Green or bare copper wire in wall box to Green terminal screw.
• Proceed to Step 6.
• Line Hot (common) wall box wire identified (tagged) when removing
old switch and First Traveler to dimmer terminal screw marked “BK”
Step 4c 3-Way Wiring with Matching Remote (w/
LEDs) for Controls with Neutral Connection
or the Black dimmer lead.
Application:
• Second Traveler wall box wire from dimmer to remote terminal screw
NOTE: Electronic Low-Voltage, Mark 10™, Quiet Fan
marked “YL/RD” (note wire color). This traveler from the remote
Speed and Electronic Switch installations only.
must go to the terminal screw on the dimmer marked “YL/RD” or the
NOTE: Dimmer is depicted.
Yellow/Red dimmer lead.
Matching Remote
Control
• Line Neutral wall box to remote terminal screw marked “WH”.
Green
Line
120VAC, 60Hz
Step 4d cont’d
WIRING COORDINATING REMOTE:
NOTE: Incandescent and Magnetic Low-Voltage
Connect wires per WIRING DIAGRAM as follows:
installations only. NOTE: Screw terminal dimmer
• Green or bare copper wire in wall box to Green terminal screw or
depicted.
Green control lead.
• Load wall box wire identified
Dimmer
Matching Remote
Matching Remote
(tagged) when removing old
(3-Way Wall box from Step 2)
(4-Way Wall box from Step 2) (3-Way Wall box from Step 2)
switch to terminal screw marked
Terminal
Terminal
Additional
Screw marked
Screw marked
Additional
"RD" or Red control lead.
Neutral Wire
White (WH)
White (WH)
Neutral Wire
• First Traveler Line Hot to terminal
4
2
screw marked "BK" or Black
3
1
Terminal
Terminal
1
Screw
marked
Screw
marked
2
control lead.
Black (BK)
Black (BK)
5
4
3
• Remove Red insulating label from
4
3
1
Terminal
2
terminal screw marked "YL/RD" or ScrewTerminal
marked
Screw marked
5
5
Yellow/Red
Yellow/Red
Yellow/Red control lead.
6
(YL/RD)
(YL/RD)
• Second Traveler wall box wire
(note color as above) to terminal
screw marked "YL/RD" or Yellow/
Red control lead. This traveler from the control must go to the
Matching Remote Matching Remote
terminal screw on the remote marked "YL/RD".
Dimmer
(w/LEDs)
(w/LEDs)
• Line neutral wall box wire to terminal screw marked "WH" or
White control lead.
Hot (Black)
BK
WH
WH
BK
BK
Green
Green
• Proceed to Step 6.
Green Ground
Black
BK
Green
Ground
Connect wires per WIRING DIAGRAM as follows:
• Green or bare copper wire in wall box to Green terminal screw or
Green dimmer lead.
Preparing and connecting wires:
• Load wall box wire identified (tagged) when removing old switch to
This remote can be wired using side wire terminal screws
dimmer terminal screw marked “RD” or the Red dimmer lead.
or through backwire openings. Choose appropriate wire
• First Traveler Line Hot to dimmer terminal screw marked “BK” or the
stripping specifications accordingly.
Black dimmer lead.
• Remove Red insulating label from terminal screw marked “YL/RD” or
Yellow/Red dimmer lead.
• Second Traveler wall box wire (note color as above) to dimmer
terminal screw marked “YL/RD” or the Yellow/Red dimmer lead. This
traveler from the dimmer must go to the terminal screw on the remote
marked “YL/RD”.
Cut
• Proceed to Step 6.
(if necessary)
WIRING MATCHING REMOTE (wall box with Line Hot
connection):
2
Neutral (White)
3-Way Wiring with Matching Remote (w/LEDs)
Application:
Terminal
Screw marked
White (WH)
1
BK
2
• Remove insulation from each wire in the wall box as shown.
NOTE: Incandescent and Magnetic Low-Voltage
installations only. NOTE: Screw terminal dimmer
depicted.
Identifying your wiring application (most
common):
1
YL/RD RD
5/8"
(1.6 cm)
2
Step 2
WH
BK
Terminal
Screw marked
Red (RD)
Back Wire
(either hole may be used)
Back wire openings use
#14-12 AWG solid copper wire
only.
INSTALLING YOUR REMOTE
Terminal
Screw marked
Black (BK)
Terminal
Screw marked
Yellow/Red
(YL/RD)
Line up tabs and
press in side to
attach
Dimmer
Coordinating Remote
Side Wire Connection
Side wire terminals accept
#14 AWG solid
Bl copper wire
only.
Strip Gage (measure
bare wire here or
use gage on back of
the dimmer)
Push in side at tab
to release
NOTE: Incandescent and Magnetic Low-Voltage
installations only. NOTE: Screw terminal dimmer
depicted.
NOTE: The control must be installed in a wall box that has a Load
connection. The matching remote must be installed in a wall box with
a Line Hot connection and a Neutral connection. A Neutral wire to the
matching remote needs to be added as shown.
If you are unsure about any part of these instructions, consult a
qualified electrician.
NOTE: Maximum wire length from control to all installed remotes
cannot exceed 300 ft (90 m).
Connect wires per WIRING DIAGRAM as follows:
NOTE: The control must be installed in a wall box that has a Line Hot
Connection.
NOTE: Maximum wire length from dimmer to all installed remotes
cannot exceed 300 ft (90 m).
• Green or bare copper wire in wall box to Green terminal screw or
Green control lead.
• Line Hot (common) wall box wire identified (tagged) when removing
old switch to terminal screw marked "BK" or Black control lead.
• First Traveler wall box wire to terminal screw marked "RD" or Red
control lead (note wire color).
• Remove Red insulating label from terminal screw marked "YL/RD"
or Yellow/Red control lead.
• Second Traveler wall box wire to terminal screw marked "YL/RD"
or Yellow/Red control lead (note wire color). This traveler from
the control must go to the terminal screw on the remote marked
"YL/RD".
• Line Neutral wall box wire to terminal screw marked "WH" or White
control lead.
Connect wires per WIRING DIAGRAM as follows:
• Green or bare copper wire in wall box to Green terminal screw.
• First Traveler and Third Traveler wall box wire from dimmer in
the 3-way box to remote terminal screw marked "BK" in the
4-way box, and to the terminal screw marked "BK" of the
remaining remote in the 3-way box.
• Second Traveler (tagged) and Fourth Traveler (tagged) wall box
wire from dimmer in the 3-way box to remote terminal screw
marked "YL/RD" in the 4-way box, and to the terminal screw
marked "YL/RD" of the remaining remote in the 3-way box (note
wire colors). This traveler from the remotes must go to the
terminal screw on the dimmer marked "YL/RD" or the Yellow/Red
dimmer lead.
• Line Neutral wall box wire to remote terminal screw marked
"WH".
WIRING MATCHING REMOTE (3-Way wall box with Line
Hot connection):
Connect wires per WIRING DIAGRAM as follows:
• Green or bare copper wire in wall box to Green terminal screw.
• Line Hot (common) wall box wire identified (tagged) when
removing old switch and First Traveler dimmer terminal screw
marked "BK" or the Black dimmer lead.
• Second Traveler wall box wire from dimmer to remote terminal
screw marked "YL/RD" (note wire color as above). This traveler
from the remote must go to the terminal screw on the dimmer
marked "YL/RD" or the Yellow/Red dimmer lead.
• Line Neutral wall box wire to remote terminal screw marked
"WH".
Step 5a cont’d 4-Way Wiring with Matching Remote (w/LEDs)
Application:
4-Way Wiring with Matching Remote (w/LEDs) for Controls
with Neutral Connection Application:
Step 5c
NOTE: Incandescent and Magnetic Low-Voltage installations
only. NOTE: Screw terminal dimmer depicted.
NOTE: Electronic Low-Voltage, Mark 10™, Quiet Fan Speed and Electronic
Switch installations only. NOTE: Dimmer is depicted.
WIRING DIMMER (3-Way wall box with Load connection):
Connect wires per WIRING DIAGRAM as follows:
• Green or bare copper wire in wall box to Green terminal screw or Green dimmer
lead.
• Load wall box wire identified (tagged) when removing old switch to dimmer terminal
screw marked "RD" or the Red dimmer lead.
• First Traveler Line Hot to dimmer terminal screw marked "BK" or the Black dimmer
lead.
• Remove Red insulating label from terminal screw marked "YL/RD" or the Yellow/
Red dimmer lead.
• Second Traveler wall box wire (note color as above) to dimmer terminal screw
marked "YL/RD" or the Yellow/Red dimmer lead. This traveler from the dimmer
must go to the terminal screw on the remote marked "YL/RD".
• Proceed to Step 6.
Step 5b
NOTE: Incandescent and Magnetic Low-Voltage installations only.
NOTE: Screw terminal dimmer depicted.
Coordinating Remote
(3-Way Wall box from Step 2)
Coordinating Remote
Dimmer
(4-Way Box from Step 2) (3-Way Wall Box from Step 2)
Terminal
Screw marked
Red (RD)
BK
WH
Terminal
Screw marked
Black (BK)
1
Terminal
Screw marked
Red (RD)
BK
YL/RD RD
1
BK
3
4
3
4
1
YL/RD RD
5
2
WH
BK
4
Terminal
Screw marked
Yellow/Red
(YL/RD)
3
YL/RD RD
5
Black
4
3
1
2
White
4
Terminal
Screw marked
Yellow/Red
(YL/RD)
5
WH
BK
Terminal
Screw marked
Black (BK)
1
Green
2
YL/RD RD
3
1
Red
6
5
Yellow/Red
Matching Remote Matching Remote
(w/LEDs)
(w/LEDs)
WH
Line
120VAC, 60Hz
Green
Ground
Green
Ground
YL/RD
YL/RD
Green
Ground
Black
Yellow/Red
Red
5
Load
White
WIRING MATCHING REMOTE (4-Way wall box with Line Hot connection):
Coordinating Remote
(no LEDs)
not used
Black
Load
WH
Coordinating Remote
(no LEDs)
BK
not used
WH
Green
Ground
RD
YL/RD
not used
BK
Green
Ground
RD
Dimmer
YL/RD
Hot (Black)
BK
Green
Ground
RD
YL/RD
Line
120VAC, 60Hz
White
Neutral (White)
WIRING COORDINATING REMOTE (4-Way box):
Connect wires per WIRING DIAGRAM as follows:
NOTE: Maximum wire length from dimmer to last remote is 300 ft (90 m).
• Green or bare copper wire in wall box to Green terminal screw.
• First Traveler and Third Traveler wall box wire (note wire colors) to terminal
screw marked "RD". These travelers from the remote in the 4-way box must go to
the terminal screw on the dimmer marked "RD" or Red dimmer lead, and to the
terminal screw marked "RD" of the remaining remote in the 3-way box.
• Second Traveler (tagged) and Fourth Traveler (tagged) wall box wire (note wire
colors) to terminal screw marked "YL/RD". These travelers from the remote in
the 4-way box must go to the terminal screw on the dimmer marked "YL/RD" or
the Yellow/Red dimmer lead, and to the terminal screw marked "YL/RD" of the
remaining remote in the 3-way box.
• Remote terminal screw marked "WH" should have White insulation label affixed.
NOTE: If insulating label is not affixed to terminal screw marked "WH", use
electrical tape to cover. Remote terminal screw marked "BK" is not used. Use
electrical tape to cover.
WIRING DIMMER (3-Way box):
Connect wires per WIRING DIAGRAM as follows:
NOTE: When using the coordinating remote without LEDs, the dimmer can be
installed on either the Line or Load side of the 3-way circuit.
NOTE: Maximum wire length from dimmer to all installed remotes cannot exceed
300 ft (90 m).
• Green or bare copper wire in wall box to Green terminal screw or Green dimmer
lead.
• Line Hot (common) wall box wire identified (tagged) when removing old switch to
dimmer terminal screw marked "BK" or Black dimmer lead.
• First Traveler wall box wire to dimmer terminal screw marked "RD" or Red dimmer
lead (note wire color as above). This traveler from the dimmer must go to the
terminal screw on the remote marked "RD".
• Remove Red insulating label from terminal screw marked "YL/RD" or Yellow/Red
dimmer lead.
• Second Traveler wall box wire to dimmer terminal screw marked "YL/RD" or Yellow/
Red dimmer lead (note wire color as above). This traveler from the dimmer must
go to the terminal screw on the remote marked "YL/RD".
WIRING COORDINATING REMOTE (3-Way box):
Connect wires per WIRING DIAGRAM as follows:
NOTE: Maximum wire length from dimmer to last remote is 300 ft (90 m).
• Green or bare copper wire in wall box to Green terminal screw.
• Load wall box wire identified (tagged) when removing old switch to terminal screw
marked "BK".
• First Traveler wall box wire (note color as above) to terminal screw marked "RD".
This traveler from the remote must go to the terminal screw on the dimmer marked
"RD" or the Red dimmer lead.
• Second Traveler wall box wire (note color as above) to terminal screw marked
"YL/RD". This traveler from the remote must go to the terminal screw on the
dimmer marked "YL/RD" or the Yellow/Red dimmer lead.
• Remote terminal screw marked "WH" should have White insulation label affixed.
NOTE: If insulating label is not affixed to terminal screw marked "WH", use
electrical tape to cover.
• Proceed to Step 6.
WIRING COORDINATING REMOTE (4-Way box):
Connect wires per WIRING DIAGRAM as follows:
NOTE: "BK" and "RD" terminals on coordinating remote are unused. Tighten both
screws.
NOTE: Maximum wire length from dimmer to last remote is 300 ft (90 m).
• Green or bare copper wire in wall box to Green terminal screw.
• Connect First Traveler wall box wire to Third Traveler wall box wire (note wire colors)
to terminal screw marked "RD" of remote in 4-way box, and to terminal screw marked
"RD" of the remaining remote in 3-way box.
• Connect Second Traveler and Fourth Traveler wall box wire (note wire colors) to
terminal screw marked "YL/RD" of remote in 4-way box, and to terminal screw marked
"YL/RD" of the remaining remote in 3-way box.
This traveler from the remotes must go to the terminal screw marked "YL/RD" or
Yellow/Red control lead.
• Remove White insulating label from terminal screw marked "WH".
• Line Neutral wall box wire to terminal screw marked "WH".
WIRING CONTROL (3-Way box):
Black
White
BK
WH
BK
Control
NOTE: The control must be installed in a wall box that has a Load connection. The
matching remote must be installed in a wall box with a Line Hot connection and a Neutral
connection. A Neutral wire to the matching remote needs to be added as shown.
If you are unsure about any part of these instructions, consult a qualified electrician.
NOTE: Maximum wire length from control to all installed remotes cannot exceed
300 ft (90 m).
4
YL/RD RD
Terminal
Screw marked
Yellow/Red
(YL/RD)
Terminal
Screw marked
Yellow/Red
(YL/RD)
Terminal
Screw marked
Black (BK)
Additional
Neutral Wire
Terminal
Screw marked
White (WH)
Additional
Neutral Wire
2
3
2
6
5
Terminal
Screw marked
White (WH)
Matching Remote
Control
(4-Way Box from Step 2) (3-Way Wall Box from Step 2)
Neutral (White)
WH
2
Matching Remote
(3-Way Wall box from Step 2)
Hot (Black)
4-Way Wiring with Coordinating Remote (no LEDs)
Application:
Step 5d cont’d
Connect wires per WIRING DIAGRAM as follows:
• Green or bare copper wire in wall box to Green terminal screw.
• First Traveler and Third Traveler wall box wire to remote terminal screw marked "BK"
in 4-way box, and to terminal screw marked "BK" of the remaining remote in 3-way
box.
• Second Traveler (tagged) and Fourth Traveler (tagged) wall box wire from control in
3-way box to remote terminal screw marked "YL/RD" in 4-way box and to terminal
screw marked "YL/RD" of the remaining remote in 3-way box (note wire colors). This
traveler from the remotes must go to the terminal screw marked "YL/RD" or
Yellow/Red control lead.
• Line Neutral wall box wire to remote terminal screw marked "WH".
WIRING MATCHING REMOTE (3-Way wall box with Line Hot connection):
Connect wires per WIRING DIAGRAM as follows:
• Green or bare copper wire in wall box to Green terminal screw.
• Line Hot (common) wall box wire identified (tagged) when removing old switch and
First Traveler wall box wire to control terminal screw marked "BK" or Black dimmer
lead.
• Second Traveler wall box wire from control to remote terminal screw marked "YL/RD"
(note wire color as above). This traveler from the remote must go to the terminal
screw marked "YL/RD" or Yellow/Red dimmer lead.
• Line Neutral wall box wire to remote terminal screw marked "WH".
WIRING CONTROL (3-Way wall box with Load connection):
Connect wires per WIRING DIAGRAM as follows:
NOTE: The control must be installed in a wall box that has a Line Hot connection.
NOTE: Maximum wire length from control to all installed remotes cannot exceed 300 ft
(90 m).
• Green or bare copper wire in wall box to Green terminal screw or Green control lead.
• Line Hot (common) wall box wire identified (tagged) when removing old switch to
terminal screw marked "BK" or Black control lead.
• First Traveler wall box wire to terminal screw marked "RD" or Red control lead (note
wire color as above).
• Remove Red insulating label from terminal screw marked "YL/RD" or Yellow/Red
control lead.
• Second Traveler wall box wire to terminal screw marked "YL/RD" or Yellow/Red
control lead (note wire color as above). This traveler from the control must go to the
terminal screw on the remote marked "YL/RD".
• Line Neutral wall box wire to terminal screw marked "WH" or White control lead.
WIRING COORDINATING REMOTE (3-Way box):
Connect wires per WIRING DIAGRAM as follows:
NOTE: "BK" and "RD" terminals on coordinating remote are unused. Tighten both
screws.
NOTE: Maximum wire length from control to last remote is 300 ft (90 m).
• Green or bare copper wire in wall box to Green terminal screw.
• Load wall box wire identified (tagged) when removing old switch to First Traveler (note
color as above).
• Second Traveler wall box wire (note color as above) to terminal screw marked
"YL/RD". This traveler from the remote must go to the terminal screw marked "YL/RD"
or Yellow/Red control lead.
• Remove White insulating label from terminal screw marked "WH".
• Line Neutral wall box wire to terminal screw marked "WH".
• Proceed to Step 6.
Coordinating Remote
(4-Way Box from Step 2)
Terminal
Screw marked
Yellow/Red
(YL/RD)
BK
WH
3
1
Terminal
Screw marked
Black (BK)
2
Terminal
Screw marked
Yellow/Red
(YL/RD)
4
YL/RD RD
5
BK
WH
White
3
4
YL/RD RD
2
1
• Restore power at circuit breaker or fuse.
• See applicable operation section to ensure dimmer or switch is functioning properly.
If lights do not turn ON, refer to the TROUBLESHOOTING section.
Green
5
3
6
Red
Yellow/Red
4
WH
Black
not used
WH
Green
Ground
RD
not used
Load
BK
Coordinating Remote
(no LEDs)
YL/RD
BK
not used
Green
Ground
RD
not used
YL/RD
Control
White
Green
Ground
Red
Black
NOTE: The lights will turn ON at brightness set on dimmer’s DIM/BRIGHT bar. The
lighting can be controlled from either the dimmer or the remote location.
Push Pad (Default settings)
LED
Brightness DIM/BRIGHT Turn ON from OFF position:
Tap – Lights turn ON to preset level.
Display
Bar
Press and Hold – Lights turn ON to full bright.
Turn OFF from ON position:
Tap – Lights turn OFF.
Press and Hold for 2 seconds – Lights remain ON for 10
seconds and then turn OFF.
DIM/BRIGHT Bar
BRIGHTEN:
Press upper half of DIM/BRIGHT Bar – Lights brighten to
desired level.
DIM:
Press lower half of DIM/BRIGHT Bar – Lights dim to desired
level.
If you continue to hold, the lights will DIM to minimum level
and then turn OFF.
Push Pad Locator
If there is a power outage, when the power is restored
Light
the lights will return to the last setting before the power
interruption.
VZ0SR Switch Remote Operation (Switch may be unlighted):
NOTE: The lights will turn ON at brightness set on dimmer’s DIM/BRIGHT bar. The
lighting can be controlled from either the dimmer or the remote location.
Push Pad (Default settings)
Turn ON from OFF position:
Tap – Lights turn ON to preset level.
Turn OFF from ON position:
Tap – Lights turn OFF.
If there is a power outage, when the
power is restored the lights will return
to the last setting before the power
interruption.
For additional information, contact Leviton’s Techline at
1-800-824-3005 or visit Leviton’s website at www.leviton.com
U.S. & Foreign Patents Pending
Copyright© 2006 Leviton Manufacturing Co., Inc.
All Rights Including Trade Dress Rights Reserved
Eco-10™ (Eco Series) is a trademark and Hi-lume® is a registered trademark of
Lutron Electronics Inc.
FCC COMPLIANCE STATEMENT
5
Coordinating Remote
(no LEDs)
VZ00R Dimmer Remote Operation (Dimmer may be unlighted):
• Lights Flickering
- Lamp has a bad connection.
- Wires not secured firmly under terminal screws of dimmer and/or remote.
• Light does not turn ON and Locator LED does not turn ON
- Circuit breaker or fuse has tripped.
- Lamp is burned out.
- Lamp Neutral connection is not wired.
• Intermittent dimmer operation
- Minimum load is under 40W.
• Remote does not operate lights
- Ensure that total wire length does not exceed 300 ft (90 m).
1
2
OPERATION
CLEANING: Clean with a damp cloth. DO NOT use chemical cleaners.
TROUBLESHOOTING
NOTE: Dress wires with a bend as shown in diagram in order to
relieve stress when mounting device.
Black
Terminal
Screw marked
Black (BK)
Restore power at circuit breaker or fuse. Installation is complete.
Locator
Light
Control
(3-Way Wall Box from Step 2)
Terminal
Screw marked
White (WH)
Step 8 Restore Power:
Push Pad
NOTE: Electronic Low-Voltage, Mark 10™, Quiet Fan Speed and
Electronic Switch installations only. NOTE: Dimmer is depicted.
Terminal
Screw marked
White (WH)
Installation may now be completed by tightening
mounting screws into wall box. Attach wallplate.
• Position all wires to provide room in outlet wall box for device.
• Ensure that the word "TOP" is facing up on the device strap.
• Partially screw in mounting screws in wall box mounting hole.
4-Way Wiring with Coordinating Remote (no LEDs) for Controls
with Neutral Connection Application:
Coordinating Remote
(3-Way Wall box from Step 2)
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE.
Step 6 Testing your Remote prior to completely
mounting in wall box:
Connect wires per WIRING DIAGRAM as follows:
• Green or bare copper wire in wall box to Green terminal screw or Green dimmer lead.
• Load wall box wire identified (tagged) when removing old switch to terminal screw
marked "RD" or Red control lead.
• First Traveler Line Hot to terminal screw marked "BK" or Black control lead.
• Remove Red insulating label from terminal screw marked "YL/RD" or Yellow/Red
control lead.
• Second Traveler wall box wire (note color as above) to terminal screw marked
"YL/RD" or Yellow/Red control lead. This traveler from the control must go to the
terminal screw on the remote marked "YL/RD".
• Line Neutral wall box wire to terminal screw marked "WH" or White control lead.
• Proceed to Step 6.
Step 5d
Step 7 Dimmer Remote Mounting:
Hot (Black)
Yellow/Red
Line
120VAC, 60Hz
White
Neutral (White)
This equipment has been tested and found to comply with the limits for a Class B
Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment OFF
and ON, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving Antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/tv technician for help.
PK-93393-10-00-2A
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for five years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option, if within such five year period the product is returned prepaid, with proof of purchase
date, and a description of the problem to Leviton Manufacturing Co., Inc., Att: Quality Assurance Department, 59-25 Little Neck Parkway, Little Neck, New York 11362-2591. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in
any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a particular purpose, is limited to five
years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
FOLD SCHEME
16.5¨
Cat. No.
6
5
4
3
2
1
15.0¨
LEVITON INSTRUCTION SHEET/MANUAL
SPECIFICATIONS
PK-93393-10-00-2A
Black
Helvetica
40 Lb. offset
Paper size:
Overall size: 16.5" x 15" (printing spec)
Final fold size: 2.75" X 3.75" (Locking fold)
Cat. No.
2.75¨
DOCUMENTATION
N/A
KKC
Cat. No.
1/24/06
3.75¨
Final Fold Size
Fold Line
Panel Line
#'s =
Fold Sequence