FAS
Power
reduces labor costs up to 50%
Easy to order – Easier to install
If you are constructing a hospital, condominium
complex, office building or hotel and the wiring
project is substantial or repetitive, look to FAS Power
products from Legrand®/Cablofil. With FAS Power,
much of the electrical assembly is completed in
advance, dramatically cutting project completion
times and saving a minimum of 50% in labor costs.
With FAS Power, all of the device choices that you
have with standard construction are available, but
with the installation ease and labor savings of a prefabricated electrical assembly. Choose from Pass &
Seymour PlugTail outlets and switches or our full
line of pre-installed devices. You can also specify
per-cut lengths of MC cable to be pre-wired into
each assembly further reducing installation time.
FAS Power will speed up the rough-in phase of your
project and inspections will never be easier because
every assembly is UL or ETL listed.
200
introduction
introduction
Setting up the initial order is also made easy with our online
configurator that helps you design and specify the precise parts
you need. You can find it on our website at www.faspower.com.
www.legrand.us/cablofil 201
FAS Power Pre-fabricated
Wiring Assemblies
Rough-in is fast and easy with FAS Power. Pre-fabricated floor brackets slide under the
sill plate with no vertical measuring needed. Wall brackets with pre-mounted boxes
and rings quickly attach to the stud with switches and switch/outlet combinations in
place. And all assemblies can be pre-wired for fast installation with Pass & Seymour
PlugTail outlets and switches connected to Southwire MCAP™ branch circuit wiring using
push connector hardware. Assemblies can then be connected to a homerun enclosure
mounted to a Cablofil cable pathway. And for fast job starts, FAS Power products are
prepackaged and shipped to the requirements of the contractor.
Pre-wired
with Pass
& Seymour
PlugTail.
Each FAS Power assembly includes:
• Floor or wall bracket with one to four gang openings
• Pre-installed boxes
• Pre-installed plaster rings are available in 1/2” to 2” raise or
adjustable style
• Far side support arms
• PlugTail or standard devices can be pre-wired to MCAP™ cable or
packaged separately
• CJ6 wire manager
FAS Power can benefit you in many ways:
• Fast job starts – FAS Power is packaged and
shipped per contractor instructions
• Reduced rough-in time – Boxes are pre-mounted
and grounded
• Pre-installed plaster rings – can be specified to
fit any wall thickness
• Pre-wired to MC cable – FAS Power assemblies can be pre-wired
to pre-cut MCAP™ cable lengths
• Painless inspections – All assemblies are UL or ETL listed
• Faster finishes – with pre-wired assemblies, just install your
PlugTail outlet/switch or remove the cover from pre-installed
devices
FAS Power now
offers PlugTail
switches from
Pass & Seymour.
Connect to home runs
supported by Cablofil Tray.
introduction
introduction
• Wide variety of device choices – PlugTail allows you to make device
choices at finish or devices can be pre-installed and protected
during drywall installation
All products contained within this brochure are either UL or ETL listed.
202
www.legrand.us/cablofil 203
FAS Power Pre-fabricated Wiring Assemblies
Floor Bracket Wired Assemblies — 1 to 4 Openings
The FAS Power Floor Bracket Wired Assembly consists of a
in every FAS Power product, including P&S PlugTail wiring
floor bracket, 4” rings, back side support arm, 4 /16” x 2 /8”
devices and Southwire MCAP metallic clad cabling.
11
1
DOUBLE OPENING FLOOR BRACKET
TM
boxes and devices that are pre-wired to precut MC cable.
All pre-installed outlets and PlugTail devices are shielded
Installation: The floor bracket is quickly installed by
in plastic to keep them finish ready during the taping and
kicking the lower flange under the wall base then securing
painting process. The boxes are mounted independent of the
with screws using predrilled holes in the bracket. At finish,
rings to allow the devices to be used for in-line or multi-wire
PlugTail allows you to quickly connect to a wide choice of
branch circuits. Legrand /Cablofil uses quality components
P&S devices in a variety of colors.
®
CF218 - RPT - 058 - 350 - MC122 - 1
back side
support arm
4” ring
4 11/16” x 2 1/8”
Box
SINGLE OPENING FLOOR BRACKET
pushwire
connectors
back side
support arm
box
mounting
height
4” ring
floor bracket
single gang
receptacle
(Not Included)
single gang
receptacle
(Not Included)
4 11/16” x 2 1/8” Box
pushwire
connectors
FOUR OPENING FLOOR BRACKET
THREE OPENING FLOOR BRACKET
TR
HG
box
mounting
height
204
single opening floor bracket catalog numbering example:
CF1 18
Bracket Type
CF1 – Floor Bracket,
Wired with Pushwire
Connectors, (1) Opening
Floor Brackets are
available with 1 thru 4
openings
Box
Mounting
Height
Box mounting
heights are
available at 12”,
15”, 18” and 24”
-
RPT
-
058
TR
-
Wiring
Components
Ring
See a complete
list of options on
page 213
See a complete
list of options on
page 213
350
-
MC122
Back Side
Arm Support
See a complete
list of options on
page 213
HG
box
mounting
height
box
mounting
height
MC Cable
single gang
receptacle
(Not Included)
(First, Second, Third,
Fourth Opening)
See a complete
list of options on
page 213
CF318 - PRT - D - D - 350 - MC122 - 1
CF418 - RPT - D - 0 - D - 058 - 350 - MC122 - 1
For a comprehensive list of floor bracket wiring assembly options, use our handy configurator at www.legrand.us/cablofil.
TR
HG
TR
f l o o r & w a l l b rx xa cx kx ex t a s s Y .
f l o o r &x xwxaxlxl b r a c k e t a s s Y .
floor bracket
single gang
receptacle
(Not Included)
www.legrand.us/cablofil 205
HG
FAS Power Pre-fabricated Wiring Assemblies
Wall Bracket Wiring Assemblies — 1 to 4 Openings
The FAS Power Wall Bracket Wired Assembly consists of a
uses quality components in every FAS Power product,
wall bracket, 4” rings, back side support arm, 4 /16” x 2 /8”
including P&S PlugTail wiring devices and Southwire
boxes and devices that are pre-wired to precut MC cable.
MCAP metallic clad cabling.
11
1
DOUBLE OPENING WALL BRACKET WIRED ASSEMBLY
WITH SINGLE GANG ADJUSTABLE RING
THREE OPENING WALL BRACKET WIRED ASSEMBLY
TM
All pre-installed outlets, switches and PlugTail devices
are shielded in plastic to keep them finish ready during
Installation: The wall bracket is quickly installed with
the taping and painting process. The boxes are mounted
screws using predrilled holes in the bracket. At finish,
independent of the rings to allow the devices to be used
PlugTail allows you to quickly connect to a wide choice
for in-line or multi-wire branch circuits. Legrand /Cablofil
of Pass & Seymour devices in a variety of colors.
®
16”
91/2”
SINGLE OPENING WALL BRACKET WIRED ASSEMBLY
5”
5”
4” ring
wall bracket
4 11/16” x 2 1/8” Box
plugtail
back side
support arm
cw2 - 0 - spt - APR1 - 350 - mc202
5”
single pole
switches
(Not Included)
SS
FOUR OPENING WALL BRACKET WIRED ASSEMBLY
cw3 - SGPT - 0 - 0 - 058- 350 - mc122 / mc122-1
S
GFI
3/4 GANG WALL BRACKET WIRED ASSEMBLY
pushwire
connectors
26”
26”
91/2”
5”
5”
206
single opening WALL bracket catalog numbering example:
Cw1
Bracket Type
CF1 – Floor Bracket,
Wired with Pushwire
Connectors, (1) Opening
Wall Brackets are
available with 1 thru 4
openings
- SS P T
- 058
- 350
-
MC202/MC202-1
Wiring
Components
Plaster
Ring
Back Side
Arm Support
See a complete
list of options on
page 213
See a complete
list of options on
page 213
See a complete
list of options on
page 213
For a comprehensive list of wall bracket wiring assembly options, use our handy configurator at www.legrand.us/cablofil.
MC Cable
(First, Second, Third,
Fourth Opening)
See a complete
list of options on
page 213
cw4 - 0 - J - 058 - 350
J
cw34 - SSSPT - 058 - 350
SSS
f l o o r & wa l l b r a c k e t a s s Y.
f l o o r & wa l l b r a c k e t a s s Y.
SS
www.legrand.us/cablofil 207
FAS Power Pre-fabricated Wiring Assemblies
Floor & Wall Brackets
The Floor Bracket is the centerpiece of our product line and represents
The Wall Bracket offers unsurpassed versatility for the installation of electrical boxes
FLOOR BRACKETS
the latest innovation by our Wiring Systems. The patented design permits
PRODUCT NO. (EA)
GANG
CENTER
HEIGHT
F112
1
12”
the bracket. Accepts 4” and 5” rings, and 4” and 4 11/16” x 2 1/8” boxes mounted horizontally
F115
1
15”
or vertically.
F118
1
18”
Wall Brackets: 18 gage galvanized steel.
horizontally or vertically.
F124
1
24”
Support Arms: Attach to the back of the Wall Bracket to support the assembly against the
Floor Brackets: 16 gage galvanized steel.
F212
2
12”
wall behind. No attachment hardware is required. Purchased separately.
F215
2
15”
assembly against the wall behind. No attachment hardware is required.
F218
2
18”
Purchased separately.
F224
2
24”
F312
3
12”
F315
3
15”
F318
3
18”
F324
3
24”
F412
4
12”
F415
4
15”
F418
4
18”
F424
4
24”
fast installation anywhere between studs and ensures correct device
mounting height with no measuring required.
Installation: The Floor Bracket is installed by kicking the lower flange
under the wall base. Two holes are provided for attachment screws if
needed. Accepts 4” and 5” rings, and 4” and 4 /16” x 2 /8” boxes mounted
11
1
Support Arms: Attach to the back of the Floor Bracket to support the
Keyhole openings allow 4” or 4 11/16” x 2 1/8” boxes to
remain attached.
Support Arms (purchased separately) are attached to
the back of the Bracket using the two slots provided.
Attachment Holes for 4” Rings allows 4 11/16” x 2 1/8”
Boxes to be mounted independently.
Attachment Holes for 4 11/16” x 2 1/8” Boxes allow 4”
Rings to be mounted independently.
Note: Floor brackets are available without
CJ6 by adding an “N” to the end
of the catalog number. ( Example: F118-N )
5”
floor & wall br acke ts
W2
2
W3
3
W4
4
W34
3
W16SL
16” Slider
W24SL
24” Slider
Attachment Holes for 4” Rings allow 4 11/16” x 2 1/8” boxes
to be mounted.
91/2”
WI
W2
16”
W3
W24SL
W16SL
6”
6”
24”
16”
16”
24”
5”
5”
26”
W4
26”
W34
floor & wall br acke ts
208
F4
1
Support Arms (purchased separately) are attached to
the back of the Bracket using the two slots provided.
5”
F3
W1
Keyhole openings allow boxes to remain attached to
the Bracket when the rings are removed.
16”
F2
GANG
Wall Bracket attachment holes
11”
FI
PRODUCT NO. (EA)
Installation: The Wall Bracket is quickly installed with screws using the holes provided in
5”
center
height
wall BRACKETS
anywhere between studs at any height.
www.legrand.us/cablofil 209
FAS Power Pre-fabricated Wiring Assemblies
Accessories — Covers
Adjustable Rings, Support Arms & Pushwire Connectors
Metal Device Covers attach to the front
adjustable rings
of receptacles and switches to protect
DC-1
from possible damage caused by drywall
PRODUCT NO. (EA)
DEVICE TYPE
apr-1-5/8
single gang
5
apr-1
single gang
3
apr-2
two gang
5
installation or painting. For use on
Standard, Decorator and Toggle-type
APR-1
APR-2
APR-3
APR-R
devices.
raise
/8” TO 11/4”
/4” TO 11/2”
/8” TO 11/2”
Material: Covers are galvanized steel.
Adjustable Rings are useful in installation where wall thicknesses are
APR-3
three gang
3
/4” TO 11/2”
Hardware is zinc-plated steel.
unknown at the time of order or electrical rough in.
apr-R
3-0 round
3
/4” TO 11/2”
Material: Galvanized steel.
metal device covers
Pushwire Connectors make the job of
DEVICE TYPE
FASTENERS
included
dc-1
single gang
(2) #8-32 screws
than ever before. Simply strip the wire, insert
PRODUCT NO. (EA)
GANG
COLOR
dc-2
two gang
(4) #8-32 screws
the conductor into the connector and you have
PC-2-YL
2
YELLOW
a solid connection. The clear housing allows
PC-4-OR
4
ORANGE
for visual inspection to ensure the proper
PC-6-PL
6
PURPLE
connection of stranded or solid conductors.
PC-8-GY
8
GRAY
Integrated test ports allow for circuit testing
PC-6-GR
6
GREEN
under an energized condition.
PC-8-GR
8
GREEN
connecting wires easier and more reliable
AR-350
DC-2
Support Arms attach
to the back of Floor,
Plastic Device Covers attach to the front of receptacles,
switches or can be snapped onto empty mud rings to keep them
clean, dust free and finish ready during the taping and painting
process. The covers are replaced later with faceplates at the
DCP-2
trim out phase of construction.
DCP-3R
Brackets to support the
assembly against the
Wire Size Range
16-12 AWG Copper Solid Conductors
18-12 AWG Copper Stranded Conductors
PC-2-YL
PC-4-OR
wall behind the devices.
PC-6-GR
No attachment hardware
Material: Zinc-plated
PRODUCT
NO. (EA)
box size / DEVICE TYPE
FASTENERS
included
DCP-1
Single gang receptacle
(2) #8-32 screws
DCP-2
Double gang receptacle
(2) #8-32 screws
DCP-3
three gang receptacle
(2) #8-32 screws
DCP-4
four gang receptacle
(2) #8-32 screws
DCP-1T
Single gang toggle switch
(2) #8-32 screws
DCP-2T
Double gang toggle switch
(2) #8-32 screws
DCP-3T
Three gang toggle switch
(2) #8-32 screws
DCP-4T
Four gang toggle switch
(2) #8-32 screws
DCP-DT
DBL. gang toggle switch & device
(2) #8-32 screws
DCP-1R
Single gang plaster ring only
None
DCP-2R
Double gang plaster ring only
None
DCP-3R
Three gang plaster ring only
None
DCP-4R
Four gang plaster ring only
None
DCP-R
3" Round plaster ring only
None
steel.
SUPPORT ARMS
PRODUCT NO.
(EA)
WALL
DEPTH
AR-300
3”
AR-350
31/2”
AR-400
4”
AR-450
4 /2”
AR-500
5”
AR-550
51/2”
AR-600
6”
AR-650
61/2”
In-sure™
PUSHWIRE CONNECTORS
PRODUCT NO. (EA)
GANG
COLOR
In-Sure™ Push-In Wire Connectors features
PI-42-OR
1
Orange
an easy-grip design that combined with a low
PI-32-RD
2
Red
insertion force makes repetitive electrical
PI-33-OR
3
Orange
connections fast and easy. All In-Sure wire
PI-34-YL
4
Yellow
connectors accept either stranded or solid
wires and include stainless steel inserts that
restrict pull-out. Built-in check ports allow for
continuity testing.
PI-34-YL
1
PI-42-OR
PI-32-RD
PI-39-BL
Wire Size Range
20-12 AWG Solid
16-12 AWG Stranded (19 strand or less)
18 AWG Stranded (7 strand)
18-14 AWG Stranded Tin-Bonded
(19 strand or less)
PI-39-BL
3
Blue
Wire Size Range
14-10 AWG Solid
12-10 AWG Stranded (19 strand or less)
14-10 AWG Stranded Tin-Bonded
(19 strand or less)
All push style connectors used in FAS Power
assemblies conform to these standards:
Voltage Rating:
600 Volts, 1000 Volts for fixtures and signs
Current Rating:
Matches the largest conductor used
Temperature Rating: 105 Degrees C
other accessories
other accessories
DCP-1T
Wall, and Universal
is required.
plastic device covers
210
PUSHWIRE CONNECTORS
PRODUCT
NO. (EA)
www.legrand.us/cablofil 211
FAS Power Pre-fabricated Wiring Assemblies
Wire & Connector Accessories
Legrand®/Pass & Seymour receptacles
and switches meet the demands of any
commercial project.
Almost any device can be specified and pre-wired into FAS Power
assemblies including GFCI, HCF and Tamper-Resistant devices. All devices
are available in standard or decorator styles and 15 to 20 amp options. And
every installed device is protected with a plastic shield that keeps them
clean, dust free and finish-ready.
Also available is P&S PlugTail™– the fastest, most consistent and reliable
device installation ever. At rough-in, install the pre-stripped leads of a
PlugTail connector instead of pigtails. With no exposed terminals the
circuit can be powered up and tested at any time.
At finish, select from a wide array of color choices for the specified device,
click in the connector and tighten the mounting screws – installation takes
less than a minute. PlugTail reduces the chance of mistakes leading to
callbacks and eliminates missed deadlines with most of the labor savings
realized at the end of the job.
For more information about Pass & Seymour products,
go to www.passandseymour.com.
FAS Power Components
OUTLETS
FAS Power prewired assemblies can specified with any length of MC cable
up to 99 feet in stranded or solid conductor types. IG and HCF versions are
also available. Type MC cable can be used anywhere Type MC or AC cable is
permitted.
l
050
½” raise
RPT
PlugTail for Duplex Outlet
l
l
058
5
RR
2 Duplex Outlets
l
l
075
¾” raise
wire & connector accessories
212
For more information about Southwire cabling products,
go to www.southwire.com.
®
/8” raise
PlugTail for 2 Duplex Outlets
l
l
100
1” raise
Tamper Resistant Duplex Outlet
l
l
125
1 1/4” raise
RTRPT
PlugTail for Tamper Resistant Duplex Outlet
l
l
150
1 1/2” raise
RRTR
2 Tamper Resistant Duplex Outlets
l
l
PlugTail for 2 Tamper Resistant Duplex Outlets
200
2” raise
l
l
Hospital Grade Duplex Outlet
APR
Adjustable
l
l
RHGPT
PlugTail for Hospital Grade Duplex Outlet
l
l
RRHG
2 Hospital Grade Duplex Outlets
l
l
PlugTail for 2 Hospital Grade Duplex Outlets
l
l
250
Duplex Outlet - Half Hot
l
l
300
3” wall depth
PlugTail for Duplex Outlet - Half Hot
l
l
350
3 ½” wall depth
RRPT
RTR
RRTRPT
RHG
RRHGPT
R/SL
R/SLPT
BACK SIDE ARM SUPPORT
2 ½” wall depth
Duplex GFCI Outlet
l
l
400
4” wall depth
GPT
PlugTail for Duplex GFCI Outlet
l
l
450
4 ½” wall depth
GG
2 Duplex GFCI Oulets
l
l
500
5” wall depth
PlugTail for 2 Duplex GFCI Oulets
l
l
550
5 ½” wall depth
Tamper Resistant Duplex GFCI Outlet
l
l
600
6” wall depth
PlugTail for Tamper Resistant Duplex GFCI Outlet
l
l
Hospital Grade Duplex GFCI Outlet
l
l
PlugTail for Hospital Grade Duplex GFCI Outlet
l
l
1 Single Pole & Duplex GFCI Outlet
l
Stranded
PlugTail for 1 Single Pole & Duplex GFCI Outlet
l
Solid
G
GGPT
GTR
GTRPT
GHG
GHGPT
SG
SGPT
MC CABLE type
hcf Stranded
Isolated Ground Duplex Outlet
l
l
RIGPT
PlugTail for Isolated Ground Duplex Outlet
l
l
hcf Solid
RRIG
2 Isolated Ground Duplex Outlets
l
l
Stranded ap
PlugTail for 2 Isolated Ground Duplex Outlets
l
l
Solid ap
RIG
hcf Stranded ap
SWITCHES
S
SPT
S3
S3PT
SS
Single-Pole Switch
l
PlugTail for Single-Pole Switch
l
Three-Way Switch
l
PlugTail for Three-Way Switch
l
2 Single-Pole Switches
l
12/4
ig Solid
l
S3S3
2 Three-Way Switches
l
PlugTail for 2 Three-Way Switches
l
1 Single Pole and 1 Three-Way Switch
l
PlugTail for 1 Single Pole and 1 Three-Way Switch
l
1 Gang Ring and 4” Box
l
l
1 Gang Ring and 4” Box with Ground Pigtail
l
l
2 Gang Ring and 4” Box
l
l
SS3PT
12/3
ig Stranded
PlugTail for 2 Single-Pole Switches
SS3
12/2
hcf Solid ap
SSPT
S3S3PT
conductors
MC CABLE
D
DGP
DD
2 Gang Ring and 4” Box with Ground Pigtail
l
l
T
1 Gang Ring Only
l
l
TT
2 Gang Ring Only
l
l
Junction Box
l
DDGP
J
4S0
4” Box Only
l
l
5S0
5” Box Only
l
l
wire & connector accessories
For additional labor savings consider using Southwire MC . UL and
NEC® compliant, it’s patented design eliminates the need for anti-short
bushings, separate ground-wire terminations and paper covering removal
from each conductor. MCAP ™ all purpose cable speeds branch circuit
make-up by up to 30% while providing a 350% better ground continuity
plan. For health care applications HFC MCAP ™ is also available.
AP ™
PLASTER RINGs
l
RRIGPT
Using MC cable with FAS Power helps you
gain a competitive advantage on every job.
Wall Floor
Duplex Outlet
R
www.legrand.us/cablofil 213