Dynasty™ 200 COMPARISON CHART Miller Dynasty 200 DX Invertec V205T $2,680.00 $2,880.00 $2,848.00 Autoline 115-460 VAC ± 10% single or three phase Yes Yes No 115/230 VAC only TIG input Amps 115V 27 Amps 27 Amps 34 Amps 100% 100A @ 14V 60% 150A @ 17V 60% 150A @ 16V 100% 100A @ 14V 60% 150A @ 17V 60% 150A @ 16V 100% 100A @ 14V 60% 170A @ 16V Not available AC TIG Amperage Range 5-200 Amps 5-200 Amps 6-200 Amps Above 85Hz (AC output) the Invertec is limited to 170 amps. DC TIG Amperage Range 1-200 Amps 1-200 Amps 6-200 Amps Adjustable Start Parameter Time / Amperage Yes Time = 1-200 ms Amperage = 1-200A Yes Time = 1-200 ms Amperage = 1-200A No Pulse Control (AC) No 0.2 - 500PPS .25 - 2.5PPS Reduce heat input and gain greater control of the weld puddle with the full range of the Dynasty 200 DX Pulse Control (DC) No 0.2-500PPS 0.25-500PPS Similar Full Feature Sequencer w/ Triggering Options No Yes No Use for semi-automated or fully automated set-ups (i.e. weld lathes or turntables). Spot Time No Yes No Achieve uniform and repeatable spot welds. 60% 100A @ 25V 60% 130A @ 26V 60% 130A @ 26V 60% 100A @ 25V 60% 130A @ 26V 60% 130A @ 26V 60% 90A @ 23.6V 60% 150A @ 26V Not Applicable Similar Similar Use the Dynasty 200 on more job sites. Excellent Excellent Not Recommended Use the Dynasty 200 for all STICK applications, 200 amps and less. Excellent for code work. Yes Yes No Yes (5-10 volts) Yes (5-10 volts) No (54 volts) Yes Yes No List Price Duty Cycle Rating TIG (115V) 1-Phase TIG (230V) 1-Phase TIG (230-460V) 3-Phase Duty Cycle Rating STICK (115) 1-Phase STICK (230V) 1-Phase STICK (230-460) 3-Phase EXX10 Arc Performance Adaptive Hot Start Low OCV for STICK Starts Dual Digital Meters Miller Dynasty 200 SD Remarks Similar Take the Dynasty 200 anywhere - as long as you have 120-460 (± 10%) VAC 1 or 3 Phase, the Dynasty will automatically connect to the available power. The V205-T draws 7 amps more a the same output 150 A @17 V Similar Similar The Dynasty 200 will work on more job sites. In conjunction with the AC frequency control, the Dynasty 200 will weld thicker material on AC. The Dynasty offers better low end amperage control on Stainless or Carbon steel. Allows starts to be tailor made for any TIG application. Provides exceptional arc starting for all STICK applications. Limits the open circuit voltage during STICK welding to just 10 volts. Allows constant monitoring of voltage and amperage while welding. ☞ COMPARISON CHART Miller Dynasty 200 DX Invertec V205T Yes Yes No 30-99% 30-99% 35-85% 20-250 Hz 20-250 Hz 20-150 Hz Above 85 Hz -the Invertec is limited to 170 amps. Yes (operates off of 5-10 volts) Yes (operates off of 5-10 volts) No (DC only) The low voltage of Lift Arc reduces the risk of tungsten inclusions and produces fast, crisp starts even on aluminum. The V205T Touch Start uses a minimum of 54 volts. The result is sticky starts with a high rate of tungsten contamination. It cannot be used on aluminum. Fan on Demand Yes Yes No This reduces the amount of dirt pulled into the machine, prolongs the life, reduces maintenance and reduces noise. Parameter Protection Lockout Yes Yes No Limits parameter adjustment to only those parameters established by the Welding Engineer or other qualified personnel. Ensures that the weld procedure will be followed. Process Memory Recall AC Balance Control AC Frequency Control AC/DC Lift Arc Miller Dynasty 200 SD Remarks Setting up the Dynasty is fast and easy. The Invertec requires working with a complex and frustrating interface. The Dynasty offers a greater range of Balance Control. More oxide cleaning if needed or a more focused arc for greater precision. Weld thicker material and gain greater arc control with the Dynasty 200. Arc Hour Counter Yes Yes No Keep track of total hours or on a particular job. Arc Cycle Counter Yes Yes No Keep track of total arc starts. Help Messages Yes Yes No Aids in set-up and troubleshooting. Made in the USA. 11/02