Disassembling the arm
Setting the rotational stop
O
Q
R
BUTTON
X
TM
180°
4
W
BUTTON
360°
b
BUTTON
CATCH
1
b BUTTON located at the lower
There is a 4
(Static-LIMB) ARM can be used for rotation
setting as well. The factory setting is for 360°
rotation. To set it to 180° rotation, push-in
the BUTTON on the Right-side of the lower
(Static-LIMB) ARM.
Rotating the monitor
S
180°
The MONITOR can be positioned in either
Landscape or Portrait orientation by simply
pivoting it 90° in either direction. A lock-out
feature stops the MONITOR from pivoting
beyond the limits.
Removing the side panels
U
To remove, use the FINGER-TABS at each
end to disengage the UPPER-CLIPS of the
SIDE-PANEL.
To switch the arm back to 360° of
rotation press the BUTTON in from the left
side of the lower arm.
To detach the FRONT-PIVOT from the
ARM, push forward the CATCH to
disengage and then Lift-Off the
FRONT-PIVOT from the ARM.
a
UNIVERSAL CLAMP
To remove the ARM, push-in the BUTTON
on the lower (Static-LIMB) ARM and Up-Lift
a
the entire ARM from the 1 BASE- SHAFT.
Attaching the side panels
T
Mount the LOWER-CLIPS at the bottom of
the SIDE-PANEL on the GROOVES of each
LIMB of the ARM. Complete the mounting
by snapping on the UPPER-CLIPS of the
SIDE-PANEL.
Changing the monitor
V
BUTTON
To detach the MONITOR from the ARM,
Press and Hold the BUTTON at the top
of the DISPLAY-MOUNT and Lift-Off the
MONITOR from the ARM.
For more information visit:
For more information visit:
www.zgonic.com
www.zgonic.com
© Copyright 2011
zgo ™ is a trademark of zgonic Pty Ltd
Adjusting the spring tension
F
E
6
1
BUTTON
1
4
L
b
4
1
d
1
c
1
a
c
3
7
TM
K
BUTTON
1
5
To install the
a
2
Push-in the BUTTON at the top of the BASESHAFT and slide the USB-HUB down the
c
1
BASE-SHAFT Tabs beneath the USB-HUB
d
will align itself with the 1 BASE-PLATE.
Monitor Arm you will need the following parts:
1 BASE
5 FRONT PIVOT
2 CLAMP
3 USB-HUB (OPTIONAL)
6 DISPLAY-MOUNT
7 SIDE PANELS (X4)
a
Push-in the BUTTON at the top of the BASEa
SHAFT and replace the 1 BASE-PLASTICb
SLEEVE and 1 BASE-METAL-SLEEVE onto
c
the 1 BASE-SHAFT.
Pull the 4 SPRING-COMPRESSION-HANDLE
outward from its stowed position in the
upper (Dynamic-LIMB) ARM.
Ensure the ARM is in the highest-position
before adjusting the tension.
H
G
M
K
N
4 ARM
Please note that all user interface parts are coloured light grey for easy identification.
Installing the base
Mounting the monitor
B
A
G
(-)
4
BUTTON
a
CLIP
1
c
4
(+)
Place the BASE flat on the desk-surface
and align it with the table-edge. The ARM
is able to tolerate desk-surfaces that are
not on level ground up to 3.5°.
Attach the CLAMP to the BASE underneath
the desk. For thinner desk mount the pins
in the top holes and for thicker desk
mount them in the lower holes.
D
C
1
1
To mount the ARM to the BASE assembly
(with or without USB-HUB, push-in the
c
BUTTON at the top of the 1 BASE- SHAFT
and slide the ARM down the
c
1
BASE-SHAFT.
I
a
a
2
+
Rotate the 4 SPRING-COMPRESSION-HANDLE
clockwise if MONITOR is too heavy and
anti-clockwise if too light. Continue adjusting
until the MONITOR “hanged” itself at the
highest-position. The User should be able
to move the MONITOR to stop at any height
thereafter. This completes the Spring-Tension
adjustment.
To save time when installing large
b
quantities, the 4 INDICATOR in the upper
(Dynamic-LIMB) ARM can be used as a
guide for the required tension.
J
M
O
P
b
4
c
a
a
free- hanging
Tighten the CLAMP to the desk by hand
a
winding the 2 HANDWHEEL in an
anti-clockwise direction. Alternatively for
multiple installations, user may use a battery
screwdriver with a 5mm hex bit. Ensure the
driver is on a low torque setting.
Push-in the BUTTON at the top of the
BASE- SHAFT and remove the
a
1
BASE-PLASTIC-SLEEVE and
b
1
BASE-METAL-SLEEVE from the
c
1
BASE- SHAFT.
Screw the DISPLAY-MOUNT onto the rear
of the MONITOR. The DISPLAY-MOUNT
accommodates both 75mm and 100mm
VESA hole-spacing.
-
Slide the CLIP of the FRONT-PIVOT into
the opening SLOT of the ARM.
BUTTON
1
b
To mount the MONITOR, slide the
DISPLAY-MOUNT down the FRONT-PIVOT
till it clicks.
a
Push the 4 SPRING-COMPRESSIONHANDLE back into its stowed position.
Route the cables around the hooks on
both sides of the lower (Static-LIMB)
and upper (Dynamic-LIMB) ARM.
Ensure sufficient “free-hanging” cable
below the MONITOR and between the
LIMBS to enable full movement in all
positions.