TL074
TL074A - TL074B
LOW NOISE J-FET QUAD OPERATIONAL AMPLIFIERS
■ WIDE COMMON-MODE (UP TO VCC+) AND
DIFFERENTIAL VOLTAGE RANGE
■ LOW INPUT BIAS AND OFFSET CURRENT
■ LOW NOISE en = 15nV/√Hz (typ)
■ OUTPUT SHORT-CIRCUIT PROTECTION
N
DIP14
(Plastic Package)
■ HIGH INPUT IMPEDANCE J–FET INPUT
STAGE
■ LOW HARMONIC DISTORTION : 0.01% (typ)
■ INTERNAL FREQUENCY COMPENSATION
■ LATCH UP FREE OPERATION
■ HIGH SLEW RATE : 13V/µs (typ)
D
SO14
(Plastic Micropackage)
ORDER CODE
DESCRIPTION
Package
The TL074, TL074A and TL074B are high speed
J–FET input quad operational amplifiers incorporating well matched, high voltage J–FET and bipolar transistors in a monolithic integrated circuit.
The devices feature high slew rates, low input bias
and offset currents, and low offset voltage temperature coefficient.
Part Number
Temperature Range
TL074M/AM/BM
TL074I/AI/BI
TL074C/AC/BC
Example : TL074IN
-55°C, +125°C
-40°C, +105°C
0°C, +70°C
N
D
•
•
•
•
•
•
N = Dual in Line Package (DIP)
D = Small Outline Package (SO) - also available in Tape & Reel (DT)
PIN CONNECTIONS (top view)
Output 1 1
14 Output 4
Inverting Input 1 2
-
-
13 Inverting Input 4
Non-inverting Input 1 3
+
+
12 Non-inverting Input 4
11 VCC -
VCC + 4
Non-inverting Input 2 5
Inverting Input 2 6
Output 2 7
March 2001
+
+
-
-
10 Non-inverting Input 3
9
Inverting Input 3
8
Output 3
1/11
TL074- TL074A - TL074B
SCHEMATIC DIAGRAM
VCC
N on- i nver t ing
i nput
I nver t ing
input
1 0 0Ω
2 0 0Ω
Output
1 0 0Ω
1/4 TL074
30k
8.2k
1.3k
1.3k
35k
35k
1 0 0Ω
VCC
ABSOLUTE MAXIMUM RATINGS
Symbol
VCC
Parameter
Supply voltage - note
TL074M, AM, BM
1)
2)
Vi
Input Voltage - note
Vid
Differential Input Voltage - note 3)
Ptot
Power Dissipation
Output Short-circuit Duration - note
4)
Toper
Operating Free-air Temperature Range
Tstg
Storage Temperature Range
1.
2.
3.
4.
2/11
TL074I, AI, BI
TL074C, AC, BC
Unit
±18
V
±15
V
±30
V
680
mW
Infinite
-55 to +125
-40 to +105
-65 to +150
0 to +70
°C
°C
All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages where the zero reference
level is the midpoint between VCC + and VCC -.
The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less.
Differential voltages are the non-inverting input terminal with respect to the inverting input terminal.
The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the dissipation rating
is not exceeded
TL074 - TL074A - TL074B
ELECTRICAL CHARACTERISTICS
VCC = ±15V, Tamb = +25°C (unless otherwise specified)
Symbol
TL074I,M,AC,AI,AM,
BC,BI,BM
Parameter
Min.
Input Offset Voltage (Rs = 50Ω)
Tamb = +25°C
Vio
DV io
Input Offset Voltage Drift
Input Offset Current - note
Tamb = +25°C
Tmin ≤ T amb ≤ T max
Iib
Input Bias Current -note 1
Tamb = +25°C
Tmin ≤ Tamb ≤ Tmax
Max.
3
3
1
10
6
3
13
7
5
Unit
Min.
Typ.
Max.
3
10
mV
TL074
TL074A
TL074B
TL074
TL074A
TL074B
Tmin ≤ Tamb ≤ Tmax
Iio
Typ.
TL074C
13
10
5
100
4
5
100
10
pA
nA
20
200
20
30
200
20
pA
nA
Avd
Large Signal Voltage Gain (R L = 2kΩ, Vo = ±10V)
Tamb = +25°C
Tmin ≤ Tamb ≤ Tmax
50
25
200
25
15
200
SVR
Supply Voltage Rejection Ratio (RS = 50Ω)
Tamb = +25°C
Tmin ≤ T amb ≤ Tmax
80
80
86
70
70
86
ICC
Supply Current, no load, per amplifier
Tamb = +25°C
Tmin ≤ T amb ≤ T max
V icm
Input Common Mode Voltage Range
CMR
Ios
±Vopp
SR
tr
Kov
GBP
Ri
V/mV
dB
mA
1.4
2.5
2.5
1.4
±11
+15
-12
±11
+15
-12
Common Mode Rejection Ratio (RS = 50Ω)
Tamb = +25°C
T min ≤ Tamb ≤ Tmax
80
80
86
70
70
86
Output Short-circuit Current
Tamb = +25°C
Tmin ≤ Tamb ≤ Tmax
10
10
40
10
10
40
10
12
10
12
12
13.5
10
12
10
12
12
13.5
8
13
8
13
Output Voltage Swing
Tamb = +25°C
Tmin ≤ T amb ≤ T max
2.5
2.5
V
dB
mA
60
60
60
60
V
RL = 2kΩ
RL = 10kΩ
RL = 2kΩ
RL = 10kΩ
Slew Rate (Tamb = +25°C)
Vin = 10V, RL = 2kΩ, CL = 100pF, unity gain
V/µs
µs
Rise Time (Tamb = +25°C)
Vin = 20mV, RL = 2kΩ, C L = 100pF, unity gain
Overshoot (Tamb = +25°C)
Vin = 20mV, RL = 2kΩ, C L = 100pF, unity gain
Gain Bandwidth Product (Tamb = +25°C)
Vin = 10mV, R L = 2kΩ, CL = 100pF, f= 100kHz
Input Resistance
µV/°C
10
1)
0.1
0.1
10
10
%
MHz
2
3
1012
2
3
1012
Ω
3/11
TL074- TL074A - TL074B
Symbol
Parameter
TL074I,M,AC,AI,AM,
BC,BI,BM
Min.
THD
en
∅m
Total Harmonic Distortion (Tamb = +25°C)
f= 1kHz, R L = 2kΩ,CL = 100pF, A v = 20dB,
Vo = 2V pp
Equivalent Input Noise Voltage
R S = 100Ω, f = 1KHz
Phase Margin
Channel separation
Vo1/Vo2
Av = 100
1.
4/11
Typ.
Max.
TL074C
Unit
Min.
Typ.
Max.
%
0.01
0.01
15
15
nV
-----------Hz
45
45
degrees
120
120
dB
The input bias currents are junction leakage currents which approximately double for every 10°C increase in the junction temperature.
TL074 - TL074A - TL074B
MAXIMUM PEAK-TO-PEAK OUTPUT
VOLTAGE versus FREQUENCY
MAXIMUM PEAK-TO-PEAK OUTPUT
VOLTAGE versus FREQUENCY
MAXIMUM PEAK-TO-PEAK OUTPUT
VOLTAGE versus FREE AIR TEMP.
MAXIMUM PEAK-TO-PEAK OUTPUT
VOLTAGE versus LOAD RESISTANCE
MAXIMUM PEAK-TO-PEAK OUTPUT
VOLTAGE versus SUPPLY VOLTAGE
MAXIMUM PEAK-TO-PEAKOUTPUT
VOLTAGE (V)
MAXIMUM PEAK-TO-PEAK OUTPUT
VOLTAGE versus FREQUENCY
30
25
RL = 10 kΩ
Tamb = +25°C
20
15
10
5
0
2
4
6
8
10
12
SUPPLY VOLTAGE ( V)
14
16
5/11
TL074- TL074A - TL074B
INPUT BIAS CURRENT versus FREE AIR
TEMPERATURE
LARGE SIGNAL DIFFERENTIAL VOLTAGE
AMPLIFICATION versus FREE AIR TEMP.
100
1000
15V
400
10
DIFFERENTIAL VOLTAGE
AMPLIFICATION (V/V)
INPUT BIAS CURRENT (nA)
V CC =
1
0.1
0.01
-50
200
100
40
20
V CC =
10
4
VO =
2
R
L
15V
10V
= 2k
Ω
1
-25
0
25
50
75
100
-75
125
-50
-25
TEMPERATURE (°C)
LARGE SIGNAL DIFFERENTIAL VOLTAGE
AMPLIFICATION AND PHASE SHIFT versus
FREQUENCY
25
50
75
100
125
TOTAL POWER DISSIPATION versus FREE AIR
TEMPERATURE
250
100
180
DIFFERENTIAL
VOLTAGE
AMPLIFICATION
(left scale)
PHASE SHIFT
(right s ca le)
10
90
R = 2 kΩ
L
C L = 1 00p F
V CC = 15 V
T amb = +125 C
1
100
1K
10K
0
10 0K
1M
10M
TOTAL POWER DISSIPATION(mW)
DIFFERENTIAL VOLTAGE
AMPLIFICATION (V/V)
0
TEMPERATURE (°C)
225
VCC = 15V
No signal
No load
200
175
150
125
100
75
50
25
0
-75
FREQUENCY (Hz)
-50
-25
0
25
50
75
100
125
TEMPERATURE (°C)
SUPPLY CURRENT PER AMPLIFIER versus
FREE AIR TEMPERATURE
COMMON MODE REJECTION RATIO versus
FREE AIR TEMPERATURE
89
V CC =
1.6
No signal
No load
1.4
15V
1.2
1.0
0.8
0.6
0.4
0.2
0
-75
-50
-25
0
25
50
TEMPERATURE (°C)
6/11
75
100
125
COMMON MODE MODE REJECTION
RATIO (dB)
SUPPLY CURRENT (mA)
2.0
1.8
88
R L = 10 kΩ
V C C=
15V
87
86
85
84
83
-75
-50
-25
0
25
50
TEMPERATURE (°C)
75
100
125
TL074 - TL074A - TL074B
OUTPUT VOLTAGE versus ELAPSED TIME
28
6
24
4
OUTPUT
OUTPUT VOLTAGE (mV)
INPUT AND OUTPUT VOLTAGES
(V)
VOLTAGE FOLLOWER LARGE SIGNAL PULSE
RESPONSE
INPUT
2
0
VCC= 15V
R L = 2 kΩ
C L= 100pF
Ta mb = +25 C
-2
-4
-6
0
0.5
1
1.5
OVERSHOOT
20
90%
16
12
8
V
4
10%
0
t
2
2.5
3
-4
3.5
= 15V
0
0.1
Tamb = +25°C
r
0.2
TIME (µs )
0.3
0.5
0.4
0.6
0.7
TIME ( µs)
EQUIVALENT INPUT NOISE VOLTAGE versus
FREQUENCY
TOTAL HARMONIC DISTORTION versus
FREQUENCY
70
A
V
15V
= 10
R S = 100 Ω
T amb = +25°C
50
40
30
20
10
0
10
40
100
400
1k
4k
FREQUENCY (Hz)
10k
40k 100k
TOTAL HARMONIC DISTORTION
(%)
1
VCC =
60
EQUIVALENT INPUT NOISE
VOLTAGE (nV/VHz)
CC
R L = 2k Ω
V VCC = = 15V
15V
CC
11
AA
V V= =
VV
= 6V
O (rms)
(rms) = 6V
0.4
O
0.1
0.04
T amb
+25°C
T amb= =
+25°C
0.01
0.004
0.001
100
400
1k
4k
10k
40k
100k
FREQUENCY (Hz)
7/11
TL074- TL074A - TL074B
PARAMETER MEASUREMENT INFORMATION
Figure 1 : Voltage Follower
Figure 2 : Gain-of-10 Inverting Amplifier
10k Ω
1k Ω
-
eI
1/4
eo
TL074
RL
CL = 100pF
TYPICAL APPLICATIONS
AUDIO DISTRIBUTION AMPLIFIER
fO = 100 kHz
1/4
1M
Ω
T L074
Output A
1 µF
1/4
-
T L074
1/4
Input
TL074
100k
Ω
100k
100k
1OO µF
Ω
Ω
V CC+
-
100k Ω
1/4
T L074
8/11
Output B
Output C
TL074 - TL074A - TL074B
TYPICAL APPLICATIONS (continued)
POSITIVE FEEDBACK BANDPASS FILTER
16 k Ω
16 k Ω
22 0p F
2 20 pF
43 k Ω
43 k Ω
43 k Ω
Input
22 0p F
1/4
TL 07 4
22 0p F
43 k Ω
30 k Ω
43 k Ω
30k Ω
-
1/4
TL 07 4
43 k Ω
-
1/4
1/4
TL 07 4
TL 07 4
1 .5 k Ω
1.5 k Ω
Output B
Ground
Output A
OUTPUT A
SECOND ORDER BANDPASS FILT ER
fo = 100kHz; Q = 30; Gain = 16
OUTPUT B
CASCADED BANDPASS FILTE R
fo = 100kHz; Q = 69; Gain = 16
9/11
TL074- TL074A - TL074B
PACKAGE MECHANICAL DATA
14 PINS - PLASTIC DIP
Millimeters
Inches
Dim.
Min.
10/11
a1
B
b
b1
D
E
e
e3
F
i
L
0.51
1.39
Z
1.27
Typ.
Max.
Min.
1.65
0.020
0.055
0.5
0.25
Typ.
Max.
0.065
0.020
0.010
20
0.787
8.5
2.54
15.24
0.335
0.100
0.600
7.1
5.1
0.280
0.201
3.3
0.130
2.54
0.050
0.100
TL074 - TL074A - TL074B
PACKAGE MECHANICAL DATA
14 PINS - PLASTIC MICROPACKAGE (SO)
G
c1
b1
e
a1
b
A
a2
C
L
s
e3
E
D
M
8
1
7
F
14
Millimeters
Inches
Dim.
Min.
A
a1
a2
b
b1
C
c1
D (1)
E
e
e3
F (1)
G
L
M
S
Typ.
Max.
Min.
0.1
1.75
0.2
1.6
0.004
0.069
0.008
0.063
0.35
0.19
0.46
0.25
0.014
0.007
0.018
0.010
0.5
Typ.
Max.
0.020
45° (typ.)
8.55
5.8
8.75
6.2
0.336
0.228
1.27
7.62
3.8
4.6
0.5
0.344
0.244
0.050
0.300
4.0
5.3
1.27
0.68
0.150
0.181
0.020
0.157
0.208
0.050
0.027
8° (max.)
Note : (1) D and F do not include mold flash or protrusions - Mold flash or protrusions shall not exceed 0.15mm (.066 inc) ONLY FOR DATA BOOK.
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted
by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject
to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not
authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
 The ST logo is a registered trademark of STMicroelectronics
 2001 STMicroelectronics - Printed in Italy - All Rights Reserved
STMicroelectronics GROUP OF COMPANIES
Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco
Singapore - Spain - Sweden - Switzerland - United Kingdom
 http://www.st.com
11/11