Installation Instructions (USA only)
MODELS DSKS433 AND DSKS333 MUST BE INSTALLED WITH CONTROL PANEL AT BOTTOM IN ORDER TO OPERATE ADEQUATELY.
Questions? Call: 800.GE.CARES (US) or visit our web site at: www.GEAppliances.com (US)
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT- Save these instructions for local
inspector’s use.
• IMPORTANT- Observe all governing codes and
ordinances.
• Note to Installer -%HVXUHWROHDYHWKHVHLQVWUXFWLRQV
with the customer.
• Note to Customer - Keep these instructions with your
Owner’s Manual for future reference.
‡%HIRUH WKH ROG GU\HU LV UHPRYHG IURP VHUYLFH RU
discarded, remove the dryer door.
• Service information and the wiring diagram are located
in the control console.
• Do not allow children on or in the appliance. Close
supervision of children is necessary when the appliance
is used near children.
‡,QVWDOO WKH GU\HU ZKHUH WKH WHPSHUDWXUH LV DERYH ƒ)
for satisfactory operation of the dryer control system.
• Product failure due to improper installation is not
covered under the Warranty.
‡'U\HUV LQVWDOOHG LQ JDUDJHV LI DOORZHG E\ ORFDO FRGHV
PXVWEHHOHYDWHGLQFKHVFPDERYHWKHÀRRU
WARNING RISK OF FIRE
• To reduce the risk of severe injury or death, follow all installation
instructions.
‡&ORWKHV GU\HU LQVWDOODWLRQ PXVW EH SHUIRUPHG E\ D TXDOL¿HG
installer.
• Install the clothes dryer according to these instructions and
in accordance with local codes. In the absence of local codes,
installation must comply with the NATIONAL ELECTRICAL
CODE, ANSI/NFPA NO. 70.
• This dryer must be exhausted to the outdoors.
• Use only 4” rigid metal ducting for exhausting the clothes dryer to
the outdoors.
‡'2 127 LQVWDOO D FORWKHV GU\HU ZLWK ÀH[LEOH SODVWLF GXFWLQJ
PDWHULDOV ,I ÀH[LEOH PHWDO VHPLULJLG RU IRLOW\SH GXFW LV
installed, it must be UL listed and installed in accordance with
the instructions found in “Connecting The Dryer To House Vent”
on page 4 of this manual. Flexible venting materials are known
to collapse, be easily crushed, and trap lint. These conditions will
REVWUXFWGU\HUDLUÀRZDQGLQFUHDVHWKHULVNRI¿UH
• Do not install or store this appliance in any location where it
could be exposed to water and or weather.
‡6DYH WKHVH LQVWUXFWLRQV ,QVWDOOHUV %H VXUH WR OHDYH WKHVH
LQVWUXFWLRQVZLWKWKHFXVWRPHU
DETERMINE ELECTRICAL REQUIREMENTS FOR YOUR DRYER MODEL
‡7KLVGU\HUPXVWEHFRQQHFWHGWRDQLQGLYLGXDOEUDQFKFLUFXLWRISURSHUYROWDJHDQGIUHTXHQF\DVVSHFL¿HGRQ5DWLQJ3ODWHORFDWHGLQVLGH
GU\HUGRRUZLWKQRRWKHUDSSOLDQFHVRU¿[WXUHVDWWDFKHG
(;&(37,21
‡$ 9 UHFHSWDFOH LV ORFDWHG RQ WKH EDFN RQ WKH GU\HU DQG LV DYDLODEOH RQO\ IRU XVH ZLWK D ZDVKHU WKDW LV DȻ[HG WR WKH GU\HU ZLWK D
:')NLW,WPD\QRWEHXVHGIRUDQ\RWKHUDSSOLDQFHRUDQ\FRQGLWLRQVRWKHUWKDQVWDWHGDERYH99PRGHOVRQO\
‡%UDQFKFLUFXLWPXVWEHSURWHFWHGE\WKHUHTXLUHGWLPHGHOD\IXVHVRUFLUFXLWEUHDNHUV9RU9LQVWDOODWLRQDPSV9LQVWDOODWLRQRUDPSV
• The electrical installation must conform to the national and local codes.
208V AND 240V MODELS ARE NOT APPROVED FOR 120V INSTALLATION.
TOOLS YOU WILL NEED
MATERIALS YOU WILL NEED
SLIP JOINT PLIERS FLAT BLADE AND PHILLIPS SCREWDRIVERS
4" DIA. METAL DUCT (RECOMMENDED)
STACKING KITS FOR DRYERS
(Comes with individual Installation Instructions)
†
Over washer
- Use Wall Mount Kit WMK-35 or
- Stack Rack DSDR24 or
- Stack Rack DSR-24
†
For alcove and closet depth and width
UHTXLUHPHQWVVHHVSHFL¿FNLWLQVWUXFWLRQV
†
All stacking kits are available from your
local sales outlet.
4" DUCT
CLAMPS (2)
OR
4" DIA. FLEXIBLE METAL (SEMI-RIGID)
UL LISTED TRANSITION DUCT (IF NEEDED) 4" SPRING
KIT WX08X10077 (INCLUDES 2 ELBOWS) CLAMPS (2)
4" DIA. FLEXIBLE METAL (FOIL TYPE)
UL LISTED TRANSITION DUCT (IF NEEDED.)
EXHAUST
HOOD
SAFETY
GLASSES
DRYER POWER
CORD KIT
(NOT PROVIDED
WITH DRYER)
UL RATED
120/240V,30A
4" DIA. METAL 3/4" STRAIN RELIEF WITH 3 OR 4 PRONGS.
UL RECOGNIZED IDENTIFY THE PLUG
ELBOW
TYPE AS PER THE
HOUSE RECEPTACLE
BEFORE PURCHASING
LINE CORD.
GLOVES
DUCT TAPE
UNPACKING AND PREPARING FOR INSTALLATION
†
Prepare the area and exhaust for installation of new dryer.
†
&KHFNDQGHQVXUHWKHH[LVWLQJH[WHUQDOH[KDXVWLVFOHDQDQGPHHWVDWWDFKHGLQVWDOODWLRQVSHFL¿FDWLRQV
†
Remove the literature and accessories bag from the dryer drum. Place the literature in a convenient place.
†
Using foam pads from dryer carton, turn dryer upside down as shown.
†
Install knobs. For location, refer to the Owner’s Manual.
†
Dryer is now ready to be mounted above washer using accessory kit.
†
Remove the foam shipping pads from under dryer.
†
Move the dryer to the desired location.
†
Follow the steps in the following pages to connect the dryer to the external exhaust and power supply.
Printed in Mexico
234D2017P001 31-16710 02-13 GE
ELECTRICAL CONNECTION DETAILS
OBSERVE ALL GOVERNING CODES AND ORDINANCES
GROUNDING INSTRUCTIONS
•7KH RSHUDWLQJ YROWDJH 9ROWV $PSHUDJH $PSV DQG
)UHTXHQF\ +] RI WKLV GU\HU DUH LQGLFDWHG RQ WKH 5DWLQJ
Plate located to the right of the loading port.
• Connect this dryer to a circuit corresponding to that
indicated on Rating Plate and protected by fuses or a
circuit breaker in accordance with local codes.
• Use a power supply cord kit marked for use with clothes
GU\HU)RU9DQG9PRGHOVXVHDSRZHUVXSSO\FRUG
kit marked for use with clothes dryers.
DO NOT USE EXTENSION CORD WITH THIS APPLIANCE
)RUDOWHUQDWH9RU9SRZHUVXSSO\KRRNXSSURFHHG
DVIROORZV
• Connect supply wire leads to terminal block as shown on
sketch below, depending on type of installation.
• Make sure screws on terminal block are tight.
This appliance must be grounded. In the event of malfunction
or breakdown, grounding will reduce the risk of electric shock
by providing a path of least resistance for electrical current.
WARNING:
Improper connection of the
equipment grounding conductor can result in a risk of electric
VKRFN&KHFNZLWKDTXDOL¿HGHOHFWULFLDQRUVHUYLFHPDQLI\RX
are in doubt as to whether the appliance is properly grounded.
'RQRWPRGLI\WKHSOXJSURYLGHGZLWKWKHDSSOLDQFHLILWZLOOQRW¿W
WKHRXWOHWKDYHDSURSHURXWOHWLQVWDOOHGE\DTXDOL¿HGHOHFWULFLDQ
WARNING:
Appliance grounded to neutral
conductor through a link. If used in a mobile home, a new
construction, a recreational vehicle or if local codes do not
SHUPLWJURXQGLQJWKURXJKQHXWUDODFRQGXFWRUFRUGRUFDEOH
assembly for use with clothes dryers must be used with the
IROORZLQJ VSHFL¿FDWLRQV 7\SH 6W &DEOH 0LQ 9ROW
$PS ZLWK FORVHGORRS WHUPLQDOV DQG VHFXUHG ZLWK D 8/
recognized strain relief. See manufacturer’s instructions.
FOR THREE-WIRE SUPPLY
FOR FOUR-WIRE SUPPLY
(208V & 240V MODELS)
• Remove terminal block cover.
‡&RQQHFWWZR+27OLQHVWRRXWHUVFUHZV/DQG/RI
terminal block.
POWER SUPPLY
• Connect Neutral line to center
&25'$:*
VFUHZ1RIWHUPLQDOEORFN
MINIMUM COPPER
White Neutral Wire
Hot Wire
*UHHQ
*URXQGLQJ
Screw
*URXQG
Strap
Hot Wire
CONDUCTORS
$039
WITH TYPE UL
5(&2*1,=('
MINIMUM RATED
ƒ&
2592/7
23(5$7,21
OR 120/240 VOLT
6833/<86(21/<
$03)86(6
(208V & 240V MODELS)
• Remove terminal block cover.
‡5HPRYHJURXQGVWUDSDQGGLVFDUG5HVFUHZJUHHQ
grounding screw in place.
‡&RQQHFWWZR+27OLQHVWRRXWHUVFUHZV/DQG/RI
terminal block.
‡&RQQHFW1HXWUDOOLQHWRFHQWHUVFUHZ1RIWHUPLQDOEORFN
• Attach ground wire of power
supply to green grounding screw POWER SUPPLY CORD
beside terminal block. *UHHQRU<HOORZ $:*0,1,080
*UHHQ*URXQGLQJ6FUHZ
*URXQG:LUH
Hot
Wire
Hot
Wire
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED.
White Neutral Wire
&233(5&21'8&7256
$039:,7+&/26('
LOOP TERMINALS TYPE UL
5(&2*1,=('0,1,080
5$7('ƒ&
5(029(*5281'675$3
$1'',6&$5'25
92/723(5$7,2125
92/76833/<86(
21/<$03)86(6
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED.
• Properly strain relief the cordset or cable to the cable entry
hole with UL recognized strain relief.
• Replace terminal block cover.
• Properly strain relief the cordset or cable to the cable
entry hole with UL recognized strain relief.
• Replace terminal block cover.
3 WIRE RECEPTACLE
(10-30R)
X
Typical 30 amp receptacle for use where
local codes permit use of flexible type
power supply cord (pigtail).
G
W
Y
4-WIRE RECEPTACLE (14-30R)
Typical 30 amp receptacle for use
where local codes permit use of
flexible type power supply cord
(pigtail).
2
4-CONDUCTOR CORD
ASSEMBLY ( Type ST Cable)
Typical 30 amp cord assembly for
use where local codes do not
permit grounding through neutral.
EXHAUST INFORMATION
‡ (DFKWXUQRYHUžVKRXOGEHWUHDWHGDVRQHžWXUQ
WARNING -
SEALING OF JOINTS
IN CANADA AND IN THE
UNITED STATES, THE REQUIRED EXHAUST DUCT
DIAMETER IS 4 in (102mm). DO NOT USE DUCT LONGER
THAN SPECIFIED IN THE EXHAUST LENGTH TABLE.
• All joints should be tight to avoid leaks. The male end of each
section of duct must point away from the dryer.
• The duct shall not be assembled with screws or other fastening
means that extend into the duct and catch lint.
‡ 'XFWMRLQWVFDQEHPDGHDLUDQGPRLVWXUHWLJKWE\ZUDSSLQJWKH
overlapped joints with duct tape.
• Horizontal runs should slope down toward the outdoors 1/4 inch
per foot.
8VLQJH[KDXVWORQJHUWKDQVSHFL¿HGOHQJWKZLOO
• Increase the drying times and the energy cost.
• Reduce the dryer life.
‡$FFXPXODWHOLQWFUHDWLQJDSRWHQWLDO¿UHKD]DUG
WARNING -
INSULATION
BEFORE PERFORMING THIS
EXHAUST INSTALLATION, BE SURE TO DISCONNECT
THE DRYER FROM ITS ELECTRICAL SUPPLY.
Ductwork that runs through an unheated area or is near air conditioning
VKRXOGEHLQVXODWHGWRUHGXFHFRQGHQVDWLRQDQGOLQWEXLOGXS
EXHAUST CONNECTION
WARNING - TO REDUCE THE RISK OF
FIRE OR PERSONAL INJURY:
The correct exhaust installation is YOUR RESPONSIBILITY. Problems
due to incorrect installation are not covered by the warranty.
Remove and discard existing plastic or metal foil transition duct and
UHSODFHZLWK8/OLVWHGWUDQVLWLRQGXFW
The MAXIMUM ALLOWABLE duct length and number of bends of the
exhaust system depends upon the type of duct, number of turns, the
W\SHRIH[KDXVWKRRGZDOOFDSDQGDOOFRQGLWLRQVQRWHGEHORZ7KH
maximum duct length for rigid metal duct is shown in the table on
the next page.
• This clothes dryer must be exhausted to the outdoors.
• Use only 4” rigid metal ducting for the home exhaust duct.
‡8VH RQO\ µ ULJLG PHWDO RU 8/OLVWHG ÀH[LEOH PHWDO VHPLULJLG RU
IRLOW\SH GXFW WR FRQQHFW WKH GU\HU WR WKH KRPH H[KDXVW GXFW
It must be installed in accordance with the instructions found in
“Connecting the Dryer to House Vent” on page 4 of this manual.
• Do not terminate exhaust in a chimney, a wall, a ceiling, gas
YHQWFUDZOVSDFHDWWLFXQGHUDQHQFORVHGÀRRURULQDQ\RWKHU
concealed space of a building. The accumulated lint could create
DSRWHQWLDO¿UHKD]DUG
• Never terminate the exhaust into a common duct with a kitchen
exhaust system. A combination of grease and lint creates a
SRWHQWLDO¿UHKD]DUG
‡'RQRWXVHGXFWORQJHUWKDQVSHFL¿HGLQWKHH[KDXVWOHQJWKWDEOH
/RQJHUGXFWVFDQDFFXPXODWHOLQWFUHDWLQJDSRWHQWLDO¿UHKD]DUG
• Never install a screen in or over the exhaust duct. This will cause
OLQWWRDFFXPXODWHFUHDWLQJDSRWHQWLDO¿UHKD]DUG
• Do not assemble ductwork with any fasteners that extend into the
duct. These fasteners can accumulate lint, creating a potential
¿UHKD]DUG
• Do not obstruct incoming or exhausted air.
• Provide an access for inspection and cleaning of the exhaust
system, especially at turns and joints. Exhaust system shall be
inspected and cleaned at least once a year.
EXHAUST SYSTEM CHECK LIST
HOOD OR WALL CAP
• Terminate in a manner to prevent back drafts or entry of birds or
other wildlife.
• Termination should present minimal resistance to the exhaust
DLU ÀRZ DQG VKRXOG UHTXLUH OLWWOH RU QR PDLQWHQDQFH WR SUHYHQW
clogging.
• Never install a screen in or over the exhaust duct. This could cause
lint build up.
• Wall caps must be installed at least 12 in. above ground level or any
other obstruction with the opening pointed down.
SEPARATION OF TURNS
For best performance, separate all turns by at least 4 ft. of straight
duct, including distance between last turn and exhaust hood.
TURNS OTHER THAN 90º
‡ 2QHWXUQRIžRUOHVVPD\EHLJQRUHG
‡ 7ZRžWXUQVVKRXOGEHWUHDWHGDVRQHžWXUQ
ALTERNATE EXHAUST INSTRUCTIONS
IF YOUR DRYER COMES WITH REAR EXHAUST,
TO CHANGE TO SIDE OR BOTTOM EXHAUST:
IF YOUR DRYER COMES WITH TOP EXHAUST,
TO CHANGE TO SIDE OR REAR EXHAUST:
6”
Left knockout
• Remove rear access panel.
• Remove access panel at back of dryer to gain access
‡'LVFRQQHFW UHWDLQLQJ SODWH DQG ƒ HOERZ E\ UHPRYLQJ
to internal ducts.
203
mm
Blower
(8”)
mounting screw from the chassis and remove tape
• Disconnect duct exhaust from blower housing
securing elbow to blower housing.
UHPRYHWDSHVHFXULQJGXFW
• Remove cover plate from rear access panel and place
FOR SIDE EXHAUST:
Bottom
over top exhaust opening.
knockout
‡5HPRYHGHVLUHGNQRFNRXWSODWHHLWKHUULJKWRUOHIWVLGH
FOR SIDE EXHAUST:
‡&XWDPPòµOHQJWKRIPPµGLDULJLG
Right knockout
‡5HPRYHGHVLUHGNQRFNRXWSODWHHLWKHUULJKWRUOHIWVLGH
89 mm
GXFWDVVKRZQUHPRYHEXUUVIURPFXWHGJH
‡7DNH WKH GXFW SUHYLRXVO\ UHPRYHG DQG FXW D PP
(3½”)
• Attach this extension duct to blower housing duct.
òµ OHQJWK RI PP µ GLD ULJLG GXFW DV VKRZQ
‡$WWDFKDƒHOERZIDFLQJGHVLUHGRSHQLQJ
295 mm (11½”)
UHPRYHEXUUVIURPFXWHGJH
For Rear Exhaust
‡$WWDFKDVHFWLRQRIPPµGLDULJLGGXFW
115 mm (4½”)
•
Attach this extension duct to blower housing duct.
For
Side
Exhaust
to elbow to protrude through side of cabinet.
‡$WWDFKWKHƒHOERZIDFLQJGHVLUHGRSHQLQJ
• Seal all joints with duct tape.
‡$WWDFKDVHFWLRQRIPPµGLDULJLGGXFWWRHOERZWR
Rigid
• Reinstall rear access panel.
Metallic
protrude through side of cabinet.
Ducting
FOR BOTTOM EXHAUST:
Cut Here
• Seal all joints with duct tape.
• Remove cover plate at bottom of dryer.
• Reinstall rear access panel.
EXTENSION DUCT
‡,QVWDOODƒHOERZ
FOR REAR EXHAUST:
• Seal all joints with duct tape.
It is importat to replace the ground clip after
‡&XWDPPò´OHQJWKRIPPµGLDULJLG
cutting the exhaust duct, (on rear exhaust model)
• Reinstall rear access panel.
GXFWDVVKRZQUHPRYHEXUUVIURPFXWHGJH
‡3ODFHFRYHUSODWHUHPRYHGIURPERWWRP
• Attach this extension duct to blower housing.
RIGU\HURYHUUHDUH[KDXVWRSHQLQJ
• Seal all joints with duct tape. Reinstall near access panel.
DRYER TOP VIEW
Front of dryer
152 mm
ALCOVE OR CLOSET INSTALLATION
EXHAUST LENGTH CALCULATION
• If your dryer is approved for installation in an alcove or closet,
it will be stated on a label on the dryer back. The installation
PXVWFRQIRUPWRWKHIROORZLQJVSHFL¿FDWLRQV
RIGID (Preferred)
3DUWVDUHDYDLODEOHIURP\RXUORFDOVHUYLFHRUJDQL]DWLRQ
:;;µ;·'XFW
:;;(OERZ
:;;µ;·'XFW
:;;$OXPLQXPKRRG
WARNING:
TO PREVENT LARGE AMOUNTS
OF LINT AND MOISTURE FROM ACCUMULATING AND TO
MAINTAIN DRYER EFFICIENCY, THIS MACHINE MUST BE
EXHAUSTED OUTDOORS.
• Minimum clearances between dryer cabinet and adjacent
ZDOOVRURWKHUVXUIDFHVDUH
RECOMMENDED MAXIMUM LENGTH
Exhaust Hood Types
Use only for short
run installations
Recommended
4" DIA.
4" DIA.
4"
No. of 90°
Elbows
0
1
2
3
Rigid
Metal
14 m (46 ft)
11 m (37 ft)
9 m (30 ft)
7 m (23 ft)
2-1/2"
Rigid
Metal
11 m (37 ft)
9 m (30 ft)
6.5 m (22 ft)
4.5 m (15 ft)
Alcove
Closet
Sides
0”
1”
Top
1”
1”
Front
µ
Rear
µ
µ
‡0LQLPXP YHUWLFDO VSDFH IURP ÀRRU WR RYHUKHDG FDELQHWV
FHLOLQJHWFLVLQ
• Closet doors must be louvered or otherwise ventilated and must
FRQWDLQDWOHDVWVTXDUHLQFKHVRIRSHQDUHDHTXDOO\GLVWULEXWHG,I
the closet contains both a washer and a dryer, doors must contain
at least 120 square inches of open area equally distributed.
• )RUHYHU\H[WUDƒHOERZUHGXFHWKHDOORZDEOHYHQWV\VWHPOHQJWK
by 10 ft.
• 7ZRƒHOERZVZLOOEHWUHDWHGOLNHRQHƒHOERZ
• )RUWKHVLGHH[KDXVWLQVWDOODWLRQVDGGRQHƒHOERZWRWKHFKDUW
• The total vent system length includes all the straight portions and
HOERZVRIWKHV\VWHPWUDQVLWLRQGXFWLQFOXGHG
FLEXIBLE
7RWDO OHQJWK RI ÀH[LEOH PHWDO GXFW VKDOO QRW H[FHHG IW P 7KH
IROORZLQJNLWLVDYDLODEOHIURP\RXORFDOVHUYLFHRUJDQL]DWLRQ
NOTE: The clearances stated above are minimums.
Consideration must be given to the type accessory kit
XVHGZLWKGU\HU5HIHUWRWKHVSHFL¿FNLWLQVWUXFWLRQIRU
details.
.LW:;;µGLDÀH[LEOHPHWDOVHPLULJLG8/OLVWHGWUDQVLWLRQ
GXFWLQFOXGHVHOERZV
CONNECTING THE DRYER TO HOUSE VENT
RIGID METAL TRANSITION DUCT
• For best drying performance, a rigid metal transition duct is
recommended.
• Rigid metal transition ducts reduce the risk of crushing and
kinking.
UL-LISTED FLEXIBLE METAL (SEMI-RIGID) TRANSITION DUCT
‡,IULJLGPHWDOGXFWFDQQRWEHXVHGWKHQ8/OLVWHGÀH[LEOHPHW
DOVHPLULJLGGXFWLQJFDQEHXVHG.LW:;;
‡ 1HYHU LQVWDOO ÀH[LEOH PHWDO GXFW LQ ZDOOV FHLOLQJV ÀRRUV RU
other enclosed spaces.
‡7RWDOOHQJWKRIÀH[LEOHPHWDOGXFWVKRXOGQRWH[FHHGIHHW
P
• For many applications, installing elbows at both the dryer
DQGWKHZDOOLVKLJKO\UHFRPPHQGHGVHHLOOXVWUDWLRQVEHORZ
Elbows allow the dryer to sit close to the wall without kinking
and or crushing the transition duct, maximizing drying
performance.
• Avoid resting the duct on sharp objects.
UL-LISTED FLEXIBLE METAL (FOIL-TYPE) TRANSITION DUCT
• In special installations, it may be necessary to connect the
GU\HUWRWKHKRXVHYHQWXVLQJDÀH[LEOHPHWDOIRLOW\SHGXFW
$ 8/OLVWHG ÀH[LEOH PHWDO IRLOW\SH GXFW PD\ EH XVHG 21/<
LQLQVWDOODWLRQVZKHUHULJLGPHWDORUÀH[LEOHPHWDOVHPLULJLG
ducting cannot be used AND where a 4” diameter can be
maintained throughout the entire length of the transition duct.
‡,Q&DQDGDDQGWKH8QLWHG6WDWHVRQO\WKHÀH[LEOHPHWDOIRLO
W\SH GXFWV WKDW FRPSO\ ZLWK WKH ´2XWOLQH IRU &ORWKHV 'U\HU
7UDQVLWLRQ'XFW6XEMHFW$µVKDOOEHXVHG
‡ 1HYHU LQVWDOO ÀH[LEOH PHWDO GXFW LQ ZDOOV FHLOLQJV ÀRRUV RU
other enclosed spaces.
‡7RWDOOHQJWKRIÀH[LEOHPHWDOGXFWVKRXOGQRWH[FHHGIHHW
P
• Avoid resting the duct on sharp objects.
For best drying performance
1 Slide one end of the duct over the clothes dryer outlet pipe.
2. Secure the duct with a clamp.
:LWKWKHGU\HULQLWVSHUPDQHQWSRVLWLRQH[WHQGWKHGXFWWR
its full length. Allow 2” of duct to overlap the exhaust pipe.
&XWRȺDQGUHPRYHH[FHVVGXFW.HHSWKHGXFWDVVWUDLJKWDV
SRVVLEOHIRUPD[LPXPDLUÀRZ
4. Secure the duct to the exhaust pipe with the other clamp.
WHEN INSTALLED IN MANUFACTURED (MOBILE) HOMES
NOTE TO INSTALLER - AFTER INSTALLATION CHECK
Dryer must be exhausted to the outside. Exhaust MUST NOT be
terminated beneath mobile home. Exhaust material MUST NOT
support combustion. Installation MUST conform to Manufactured
+RPH&RQVWUXFWLRQ6DIHW\6WDQGDUG7LWOH&)53DUW
or when such standard is not applicable, the American National
6WDQGDUGRI0RELOH+RPHV$16,1)5$1R%)RUHOHFWULFDO
connection, see “Connecting dryer using 4 wire connection”.
THE FOLLOWING:
†(;+$867'8&70XVWPHHWVSHFVRQSDJH1RH[FHVVLYH
WXUQV1RNLQNVRUREVWUXFWLRQVWRDLUÀRZ
†(;+$867+22'6KRXOGZRUNIUHHO\DQGRSHQGRZQZDUG
†*5281',1*'U\HUPXVWEHSURSHUO\JURXQGHGWRFRQIRUPWR
local codes and ordinance requirements.
†23(5$7,217XUQGU\HURQDQGFKHFNIRUKHDW
†+$1'&86720(57+(2:1(5·60$18$/*LYHLQVWUXFWLRQVRQ
RSHUDWLQJWKHGU\HU$QVZHUDQ\TXHVWLRQV
†*,9(7+(6(,167$//$7,21,16758&7,216WRWKHFXVWRPHU
USE OF CASTERS (120V PORTABLE MODELS ONLY)
4
For a portable installation screw casters into the holes on the bottom of the
dryer. Refer to the “Installation Instructions for caster assembly” sheet to
install casters.