IMPORTANT SAFTEY INSTRUCTIONS Must be installed by a qualified technician. Read these installation instructions. Keep these instructions for future use. Follow all instructions. Install in accordance with manufacturer's instructions. FAILURE TO FOLLOW INSTRUCTIONS COULD RESULT IN DEATH OR SERIOUS INJURY. FAILURE TO FOLLOW INSTRUCTIONS VOIDS WARRANTY. This luminaire must be mounted or supported independently of an outlet box. Make sure electrical connections are wired correctly. Power and neutral wires must be connected to the luminaire disconnect. Insert the power wire into the black colored insert and the neutral wire into the white colored insert. The ground must be connected. Do not defeat the safety purpose of the grounding wire inside the chassis. The chassis must be grounded to avoid possible electrical shock. CAUTION READ ALL INSTRUCTIONS PRIOR TO INSTALLATION WARNING: TO PREVENT INJURY, THE MIRROR MUST BE INSTALLED IN ACCORDANCE WITH THE MANUFACTURER’S INSTRUCTIONS CAUTION: THE ONLY USER SERVICEABLE PARTS INSIDE ARE THE LAMPS. OTHER COMPONENTS MUST BE SERVICED BY QUALIFIED ELECTRICIANS. LUMINAIRE DISCONNECT MUST BE DISCONNECTED PRIOR TO COMPONENT SERVICING UNPACKING YOUR LIGHTED MIRROR Verify Contents Prior to installation, unpack items and verify contents. The lighted mirror comes with 2 boxes and lamps (or LEDs which come pre-installed in the chassis): BOX 1: CHASSIS ASSEMBLY Label will end with -C. BOX 2: MIRROR ASSEMBLY WITH INTEGRAL HANGERS Label will end with -M. Please note, the Fusion chassis and mirror images are shown here, but these instructions are meant to be used for all wall mounted lighted mirrors. 2 THERE’S ONLY ONE™ ELECTRIC MIRROR® | E sales@electricmirror.com | T +1 425 776-4946 | F +1 425-491-8200 | W www.electricmirror.com INSTALLATION 1. MOUNT THE CHASSIS ON THE WALL Before mounting chassis on wall, identify mirror location on wall. Drill marks should be measured from the edge of the mirror NOT FROM EDGE OF CHASSIS. There are multiple mounting holes that can be chosen from to accommodate mounting locations. The chassis shall be installed with a minimum of (4) 1/4” x 1-1/2” lag screws or other engineering approved fasteners. Use wall anchors or reinforced backing areas to support chassis. See individual product specifications for mounting hole locations. 2. INSTALL LAMPS (For Lighted Mirrors with LEDs pre-installed, skip to step 3.) Lamps should fit within the lamp holders provided in chassis. Rotate lamps to lock into place. 3. WIRING DETAILS Please note, all electrical installations should be carried out by a fully qualified electrician in conformance with the National Electrical Code and local building codes. 4. POWER CONNECTION Before proceeding to power supply wiring, make sure the MC cable is brought in through the wall and into the chassis knockout. READ AND COMPLY WITH THE INSTRUCTIONS ON THE DIMMING CONTROLLER. Insert ground wire in the grounded connector. Insert the hot and neutral wires into the luminaire disconnect. The hot wire is inserted into the black port (number 1) and the neutral wire is inserted into the white port (number 2). Base model Lighted Mirrors with T5 Fluroescents are not dimmable (without a dimming ballast upgrade). For Lighted Mirrors with the dimming ballast upgrade, or dimmable LEDs, please refer to the dimming requirement document. For other upgrade options such as Keen or Vive, please refer to those instructions. For the Night Light upgrade with a dimmable lighted mirror, a separate on/off switch if required. A base model lighted mirror with T5 Fluorescents and a night light upgrade (no dimming) can use the following switch: 15A, 120/277V, rocker or toggle, double-throw center-off maintained contact single pole. MODEL: Leviton #5685-2W or equivalent. (Not provided by Electric Mirror). THERE’S ONLY ONE™ ELECTRIC MIRROR® | E sales@electricmirror.com | T +1 425 776-4946 | F +1 425-491-8200 | W www.electricmirror.com 3 A lighted mirror with the LED clock upgrade will typically require both a switched hardwire connection for the lights and a separate unswitched hardwire connection for the clock. 5. MIRROR MOUNTING After wiring process is completed, mirror is ready to be hung on the chassis. The weight of the mirror is supported at the top of the chassis. The mirror clip, at the bottom of mirror, is used to keep the mirror from moving away from the wall. Hang mirror on chassis by aligning tabs on chassis through mirror hanger slots while holding the mirror against the chassis. Slide the mirror down inserting the chassis tabs into the hanger slots. Make sure all tabs are engaged through hanger slots and the mirror clip overlaps the chassis flange. Make sure to leave a 1” clearance above the glass so the mirror can lift above the chassis tab for installation and maintenance. Width x Height Orientation All Lighted Mirrors must be mounted in the width x height orientation shown. Since the mirror hangs on the chassis using gravity, it cannot be mounted sideways. A Note about Recessed Installations The Lighted Mirrors are meant to be surface mounted, typically. If you would like to recess your Lighted Mirror, ensure that the ¼” mirror is proud of the wall and just the chassis should be partially recessed. Make sure to leave a 1” clearance above the glass so the mirror can lift up for installation and maintenance. 4 THERE’S ONLY ONE™ ELECTRIC MIRROR® | E sales@electricmirror.com | T +1 425 776-4946 | F +1 425-491-8200 | W www.electricmirror.com