LV switch-disconnectors
Interpact INS/INV
40 to 2500 A
Modularity…
the sky is the limit
Building a New Electric World
General
contents
Presentation
Schneider Electric
2
Functions and characteristics
17
Installation recommendations
63
Dimensions and connection
87
Additionnal characteristics
105
Catalogue numbers
115
1
16
Schneider Electric
Functions and characteristics
Presentation
General characteristics
Switch-disconnector selection
18
20
Interpact INS40 to 160
Interpact INS250-100 to 630
Interpact INS630b to 2500
Interpact INV100 to 630
Interpact INV630b to 2500
20
24
28
32
36
Complete source-changeover assembly selection
40
Interpact INS250-100 to 630
40
Installation
Connection
44
45
Interpact INS40 to 160
Interpact INS250 to 630 / INV100 to 630
Interpact INS630b to 2500 / INV630b to 2500
45
48
51
Electrical and mechanical accessories
46
Interpact INS250 / INV100 to 250
Interpact INS320 to 630 / INV320 to 630
Interpact INS630b to 2500 / INV630b to 2500
46
47
50
Connection accessories
52
Distribution blocks
One-piece spreader
Insulation of live parts
52
53
54
Auxiliary contacts
Current measurements
Rotary handle
Coupling accessories
Disabling device closing
Switching to a replacement source
Accessories
55
56
57
58
59
60
61
Installation recommendations
Dimensions and connection
Additional characteristics
Catalogue numbers
Schneider Electric
2
63
85
103
113
17
Functions and
characteristics
Switch-disconnector selection (cont.)
Interpact INS40 to 160
052164_B
Interpact INS switch-disconnectors
Number of poles
Electrical characteristics as defined by IEC 60947-1 / 60947-3 and EN 60947-1 / 60947-3
Conventional thermal current (A)
Conventional thermal current
in enclosure
Rated insulation level (V)
Impulse-withstand voltage (kV)
Rated operational voltage (V)
at 60 °C
at 60 °C
Ui
Uimp
Ue
AC 50/60 Hz
Rated operational voltage AC20 and DC20 (V)
AC 50/60 Hz
DC
AC 50/60 Hz
Rated operational current (A)
Electrical AC
Ie
052168_A
Interpact INS80 switch-disconnector
Ith
Ithe
50/60 Hz
220-240 V
380-415 V
440-480 V (1)
500 V
660-690 V
Electrical DC
125 V (2P in series)
250 V (4P in series)
Rated operational power AC23 (kW)
Electrical AC
Rated duties
uninterrupted duty
intermittent duty
min. (switch-disconnector alone)
max. (with upstream protection circuit breaker)
1s
3s
20 s
30 s
059202_A
Interpact INS160 switch-disconnector
Short-circuit making capacity
Short-time withstand current
Icm
(kA peak)
Icw (A rms)
Suitability for isolation
Durability (category A) (O - C-O cycles)
50/60 Hz
220-240 V
230 V (NEMA)
380-415 V
440 V
480 V (NEMA)
500-525 V
660-690 V
Mechanical
Electrical AC
Interpact INS160 emergency-off switch-disconnector
50/60 Hz
220-240 V
380-415 V
440 V
500 V
690 V
Electrical DC
250 V
Positive contact indication
Visible break
Emergency-off switch disconnector
Degree of pollution
Upstream protection
See the “Additional characteristics” section, 308E5010
(1) Suitable for 480 V NEMA.
20
Schneider Electric
Switch-disconnector selection (cont.)
Interpact INS40 to 160 (cont.)
Functions and
characteristics
INS40
INS63
INS80
INS100
INS125
INS160
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
40
40
63
63
80
80
100
100
125
125
160
160
690
8
500
250
690
690
8
500
250
690
690
8
500
250
690
750
8
690
250
750
750
8
690
250
750
750
8
690
250
750
AC22A
40
40
40
40
–
AC23A
40
40
40
32
–
AC22A
63
63
63
63
–
AC23A
63
63
63
40
–
AC22A
80
80
80
80
–
AC23A
80
72
63
40
–
AC22A
100
100
100
100
100
AC23A
100
100
100
100
63
AC22A
125
125
125
125
125
AC23A
125
125
125
125
80
AC22A
160
160
160
160
160
AC23A
160
160
160
160
100
DC22A
40
40
DC23A
40
40
DC22A
63
63
DC23A
63
63
DC22A
80
80
DC23A
80
80
DC22A
100
100
DC23A
100
100
DC22A
125
125
DC23A
125
125
DC22A
160
160
DC23A
160
160
11
7.5
20
22
22
18.5
–
b
class 120 - 60 %
15
75
3000
1730
670
550
b
20000
15
15
30
30
30
22
–
b
class 120 - 60 %
15
75
3000
1730
670
550
b
20000
22
15
37
37
30
22
–
b
class 120 - 60 %
15
75
3000
1730
670
550
b
20000
22
22
45
55
55
55
55
b
class 120 - 60 %
20
154
5500
3175
1230
1000
b
15000
37
37
55
55
75
75
75
b
class 120 - 60 %
20
154
5500
3175
1230
1000
b
15000
45
45
75
90
90
110
90
b
–
20
154
5500
3175
1230
1000
b
15000
AC22A
1500
1500
1500
1500
–
AC23A
1500
1500
1500
1500
–
AC22A
1500
1500
1500
1500
–
AC23A
1500
1500
1500
1500
–
AC22A
1500
1500
1500
1500
–
AC23A
1500
1500
1500
1500
–
AC22A
1500
1500
1500
1500
1500
AC23A
1500
1500
1500
1500
1500
AC22A
1500
1500
1500
1500
1500
AC23A
1500
1500
1500
1500
1500
AC22A
1500
1500
1500
1500
1500
AC23A
1500
1500
1500
1500
1500
DC22A
1500
b
–
b
III
DC23A
1500
DC22A
1500
b
–
b
III
DC23A
1500
DC22A
1500
b
–
b
III
DC23A
1500
DC22A
1500
b
–
b
III
DC23A
1500
DC22A
1500
b
–
b
III
DC23A
1500
DC22A
1500
b
–
b
III
DC23A
1500
–
Schneider Electric
–
–
–
–
–
21
Switch-disconnector selection (cont.)
Interpact INS40 to 160 (cont.)
Functions and
characteristics
Interpact INS switch-disconnectors
Installation
Fixed, front connection
Fixed, rear connection
On symmetrical rails
On a backplate
Connection
By cables
By cables with lugs
Flat-facing bars
Edgewise bars
to bare cable connectors
directly to terminals
to spreaders
to vertical-connection adapters via cable-lug adapters
directly to terminals
to spreaders
to vertical-connection adapters
Indication and measurement auxiliaries
Auxiliary contacts
Voltage-presence indicator
Current-transformer module
Ammeter module
Control, locking and interlocking
Control
Locking
Interlocking
direct front rotary handle
extended front rotary handle
direct lateral rotary handle
extended lateral rotary handle
by keylock
by padlocks
by keylock
mechanical
Complete source-changeover assembly
Operating torque (Nm) (typical value for 3/4 poles with front handle)
Installation and connection accessories
Bare cable connectors
Rear connectors
Terminal extensions
Spreaders
One-piece spreader
Terminal shrouds
Terminal shields
Interphase-barrier
Front panel escutcheons
Coupling accessories
Tightening torque for electrical connections (Nm)
Dimensions and weights
Overall dimensions H x W x D (mm)
Approximate weight (kg)
3 poles
4 poles
3 poles
4 poles
Enclosure dimensions for Ithe
E90489
H x W x D (mm)
H
D
22
W
Schneider Electric
Switch-disconnector selection (cont.)
Interpact INS40 to 160 (cont.)
Functions and
characteristics
INS40
INS63
INS80
INS100
INS125
INS160
b
–
b
b
b
–
b
b
b
–
b
b
b
b
–
b
b
b
–
b
b
b
–
b
b
–
–
–
–
–
–
b
–
–
–
–
–
–
b
–
–
–
–
–
–
b
b
–
–
b
–
–
b
b
–
–
b
–
–
b
b
–
–
b
–
–
b
–
–
–
b
–
–
–
b
–
–
–
b
–
–
–
b
–
–
–
b
–
–
–
b
b
b
b
–
b
–
b
–
0.7 < C < 1.3
b
b
b
b
–
b
–
b
–
0.7 < C < 1.3
b
b
b
b
–
b
–
b
–
0.7 < C < 1.3
b
b
b
b
–
b
–
b
b
1.4 < C < 2
b
b
b
b
–
b
–
b
b
1.4 < C < 2
b
b
b
b
–
b
–
b
b
1.4 < C < 2
b
–
–
–
–
b
b
b
–
–
8
b
–
–
–
–
b
b
b
–
–
8
b
–
–
–
–
b
b
b
–
–
8
b
–
–
–
–
b
b
b
–
–
8
b
–
–
–
–
b
b
b
–
–
8
b
–
–
–
–
b
b
b
–
–
8
90 x 81 x 62.5
90 x 81 x 62.5
0.5
0.6
90 x 81 x 62.5
90 x 81 x 62.5
0.5
0.6
90 x 81 x 62.5
90 x 81 x 62.5
0.5
0.6
135 x 100 x 62.5
135 x 100 x 62.5
0.8
0.9
135 x 100 x 62.5
135 x 100 x 62.5
0.8
0.9
135 x 100 x 62.5
135 x 100 x 62.5
0.8
0.9
115 x 190 x 55
115 x 190 x 55
115 x 190 x 55
160 x 260 x 55
160 x 260 x 55
160 x 260 x 55
Schneider Electric
23
Functions and
characteristics
Switch-disconnector selection (cont.)
Interpact INS250-100 to 630
056648_A
Interpact INS switch-disconnectors INS
Number of poles
Electrical characteristics as defined by IEC 60947-1 / 60947-3 et EN 60947-1 / 60947-3
Conventional thermal current (A)
Conventional thermal current
in enclosure
Rated insulation level (V)
Impulse-withstand voltage (kV)
Rated operational voltage (V)
Ith
Ithe
at 60 °C
at 60 °C
Ui
Uimp
Ue
AC 50/60 Hz
Rated operational voltage AC20 and DC20 (V)
AC 50/60 Hz
DC
AC 50/60 Hz
Rated operational current (A)
Electrical AC
Ie
056652_B
Interpact INS250 switch-disconnector
50/60 Hz
220-240 V
380-415 V
440-480 V (1)
500-525 V
660-690 V
Electrical DC
125 V (2P in series)
250 V (4P in series)
Interpact INS250 emergency-off switch-disconnector
Rated operational power AC23 (kW)
Electrical AC
Rated duties
uninterrupted duty
intermittent duty
min. (switch-disconnector alone)
max. (with upstream protection circuit breaker)
1s
3s
20 s
30 s
Short-circuit making capacity
059487_B
Short-time withstand current
Icm
(kA peak)
Icw (A rms)
Suitability for isolation
Durability (category A) (O - C-O cycles)
50/60 Hz
220-240 V
230 V (NEMA)
380-415 V
440 V
480 V (NEMA)
500-525 V
660-690 V
Mechanical
Electrical AC
50/60 Hz
440 V
500 V
690 V
Electrical DC
250 V
Interpact INS400 switch-disconnector
Positive contact indication
Visible break
Emergency-off switch disconnector
Degree of pollution
Upstream protection
059488_B
See the “Additional characteristics” section, 308E5015
Interpact INS400 emergency-off switch-disconnector
(1) Suitable for 480 V NEMA.
(2) 550 A (DC).
24
Schneider Electric
Switch-disconnector selection (cont.)
Interpact INS250-100 to 630 (cont.)
Functions and
characteristics
INS250-100 INS250-160 INS250-200 INS250
INS320
INS400
INS500
INS630
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
100
100
160
160
200
200
250
250
320
320
400
400
500
500
630
630 (2)
750
8
690
250
750
750
8
690
250
750
750
8
690
250
750
750
8
690
250
750
750
8
690
250
750
750
8
690
250
750
750
8
690
250
750
750
8
690
250
750
AC22A
100
100
100
100
100
AC23A
100
100
100
100
100
AC22A
160
160
160
160
160
AC23A
160
160
160
160
160
AC22A
200
200
200
200
200
AC23A
200
200
200
200
200
AC22A
250
250
250
250
250
AC23A
250
250
250
250
250
AC22A
320
320
320
320
320
AC23A
320
320
320
320
320
AC22A
400
400
400
400
400
AC23A
400
400
400
400
400
AC22A
500
500
500
500
500
AC23A
500
500
500
500
500
AC22A
630
630
630
630
630
AC23A
630
630
630
630
630
DC22A
100
100
DC23A
100
100
DC22A
160
160
DC23A
160
160
DC22A
200
200
DC23A
200
200
DC22A
250
250
DC23A
250
250
DC22A
320
320
DC23A
320
320
DC22A
400
400
DC23A
400
400
DC22A
500
500
DC23A
500
500
DC22A
550
550
DC23A/B
550/630
550/630
22
22
45
55
55
55
55
b
class 120 - 60 %
30
330
8500
4900
2200
1800
b
15000
45
45
75
90
90
110
90
b
class 120 - 60 %
30
330
8500
4900
2200
1800
b
15000
55
55
90
110
110
132
160
b
class 120 - 60 %
30
330
8500
4900
2200
1800
b
15000
75
75
132
150
150
160
210
b
class 120 - 60 %
30
330
8500
4900
2200
1800
b
15000
90
90
160
185
185
220
250
b
class 120 - 60 %
50
330
20000
11500
4900
4000
b
10000
110
110
200
220
220
250
400
b
class 120 - 60 %
50
330
20000
11500
4900
4000
b
10000
132
150
250
250
250
355
500
b
class 120 - 60 %
50
330
20000
11500
4900
4000
b
10000
200
200
315
400
375
400
560
b
class 120 - 60 %
50
330
20000
11500
4900
4000
b
10000
AC22A
1500
1500
1500
AC23A
1500
1500
1500
AC22A
1500
1500
1500
AC23A
1500
1500
1500
AC22A
1500
1500
1500
AC23A
1500
1500
1500
AC22A
1500
1500
1500
AC23A
1500
1500
1500
AC22A
1500
1500
1500
AC22A
1500
1500
1500
AC22A
1500
1500
1500
AC22A
1500
1500
1500
DC22A
1500
b
–
b
III
DC23A
1500
DC22A
1500
b
–
b
III
DC23A
1500
DC22A
1500
b
–
b
III
DC23A
1500
DC22A
1500
b
–
b
III
DC23A
1500
DC23A
1000
b
–
b
III
DC23A
1000
b
–
b
III
DC23A
1000
b
–
b
III
DC23A
1000/200
b
–
b
III
–
–
–
–
–
Schneider Electric
–
–
–
AC23A
1500
1500
1500
AC23A
1500
1500
1500
AC23A
1500
1500
1500
AC23A
1500
1500
1500
25
Switch-disconnector selection (cont.)
Interpact INS250-100 to 630 (cont.)
Functions and
characteristics
Interpact INS switch-disconnectors
Installation
Fixed, front connection
Fixed, rear connection
On symmetrical rails
On a backplate
Connection
By cables
By cables with lugs
Flat-facing bars
Edgewise bars
to bare cable connectors
directly to terminals
to spreaders
to vertical-connection adapters
directly to terminals
to spreaders
to vertical-connection adapters
Indication and measurement auxiliaries
Auxiliary contacts
Voltage-presence indicator
Current-transformer module
Ammeter module
Control, locking and interlocking
Control
Locking
Interlocking
direct front rotary handle
extended front rotary handle
direct lateral rotary handle
extended lateral rotary handle
by keylock
by padlocks
by keylock
mechanical
Complete source-changeover assembly
Operating torque (Nm) (typical value for 3/4 poles with front handle)
Installation and connection accessories
Bare cable connectors
Rear connectors
Terminal extensions
Spreaders
One-piece spreader
Terminal shrouds
Terminal shields
Interphase-barrier
Front panel escutcheons
Coupling accessories
Tightening torque for electrical connections (Nm)
Dimensions and weights
Overall dimensions H x W x D (mm)
Approximate weight (kg)
3 poles
4 poles
3 poles
4 poles
Enclosure dimensions for Ithe
E90489
H x W x D (mm)
H
D
26
W
Schneider Electric
Switch-disconnector selection (cont.)
Interpact INS250-100 to 630 (cont.)
Fonctions et
caractéristiques
INS250-100 INS250-160 INS250-200 INS250
INS320
INS400
INS500
INS630
b
b
–
b
b
b
–
b
b
b
–
b
b
b
–
b
b
b
–
b
b
b
–
b
b
b
–
b
b
b
–
b
b
b
b
–
b
b
–
b
b
b
–
b
b
–
b
b
b
–
b
b
–
b
b
b
–
b
b
–
b
b
b
–
b
b
b
b
b
b
–
b
b
b
b
b
b
–
b
b
b
b
b
b
–
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
5 < C < 6.2
b
b
b
b
b
b
b
b
b
5 < C < 6.2
b
b
b
b
b
b
b
b
b
5 < C < 6.2
b
b
b
b
b
b
b
b
b
5 < C < 6.2
b
b
–
–
b
b
b
b
b
13.5 < C < 16.5
b
b
–
–
b
b
b
b
b
13.5 < C < 16.5
b
b
–
–
b
b
b
b
b
13.5 < C < 16.5
b
b
–
–
b
b
b
b
b
13.5 < C < 16.5
b
b
b
b
b
–
b
b
b
b
15
b
b
b
b
b
–
b
b
b
b
15
b
b
b
b
b
–
b
b
b
b
15
b
b
b
b
b
–
b
b
b
b
15
b
b
b
b
–
–
b
b
b
b
50
b
b
b
b
–
–
b
b
b
b
50
b
b
b
b
–
–
b
b
b
b
50
b
b
b
b
–
–
b
b
b
b
50
140 x 136 x 86
140 x 136 x 86
2
2.2
140 x 136 x 86
140 x 136 x 86
2
2.2
140 x 136 x 86
140 x 136 x 86
2
2.2
140 x 136 x 86
140 x 136 x 86
2
2.2
185 x 205 x 120
185 x 205 x 120
4.6
4.9
185 x 205 x 120
185 x 205 x 120
4.6
4.9
185 x 205 x 120
185 x 205 x 120
4.6
4.9
185 x 205 x 120
185 x 205 x 120
4.6
4.9
300 x 400 x 200
300 x 400 x 200
300 x 400 x 200
300 x 400 x 200
400 x 600 x 200
400 x 600 x 200
400 x 600 x 200
400 x 600 x 200
Schneider Electric
27
Functions and
characteristics
Switch-disconnector selection (cont.)
Interpact INS630b to 2500
Interpact INS switch-disconnectors
Number of poles
E59503_A
Electrical characteristics as defined by IEC 60947-1 / 60947-3 and EN 60947-1 / 60947-3
Conventional thermal current (A)
Conventional thermal current
in enclosure
Rated insulation level (V)
Impulse-withstand voltage (kV)
Rated operational voltage (V)
Ith
Ithe
at 60 °C
at 60 °C
Ui
Uimp
Ue
AC 50/60 Hz
AC 50/60 Hz
DC
Rated operational voltage AC20 and DC20 (V)
Rated operational current (A)
Ie
Electrical AC
50/60 Hz
220-240 V
380-415 V
440-480 V (1)
500-525 V
660-690 V
Electrical DC
Interpact INS800 switch-disconnector
E00000
125 V / (2P in series)
250 V / (4P in series)
Rated operational power AC23 (kW)
Electrical AC
Rated duties
uninterrupted duty
intermittent duty
min. (switch-disconnector alone)
max. (with upstream protection circuit breaker)
0.5 s
1s
3s
20 s
30 s
Nouvelle photo à venir
Short-circuit making capacity
Short-time withstand current
Suitability for isolation
Durability (category A) (O - C-O cycles)
Icm
(kA peak)
Icw (A rms)
Mechanical
Electrical AC
Interpact INS800 emergency-off switch-disconnector
50/60 Hz
220-240 V
230 V (NEMA)
380-415 V
440 V
480 V (NEMA)
500-525 V
660-690 V
50/60 Hz
220-240 V
380-415 V
440-480 V (1)
500-525 V
660-690 V
Electrical DC
125 V / 2 poles
250 V / 4 poles
Positive contact indication
Visible break
Emergency-off switch disconnector
Degree of pollution
Upstream protection
See the “Additional characteristics” section, 308E5025 and 308E5030
(1) Suitable for 480 V NEMA.
(2) For vertical connection busbars only; for horizontal
connection busbars, see derating chart in "Installation
recommendations".
28
Schneider Electric
Switch-disconnector selection (cont.)
Interpact INS630b to 2500 (cont.)
Functions and
characteristics
INS630b
INS800
INS1000
INS1250
INS1600
INS2000
INS2500
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
630
630
800
800
1000
1000
1250
1250
1600 (2)
1600 (2)
2000
2000
2500
2500
1000
12
690
250
1000
1000
12
690
250
1000
1000
12
690
250
1000
1000
12
690
250
1000
1000
12
690
250
1000
1000
12
690
250
1000
1000
12
690
250
1000
AC21A/AC23A
AC21A
AC22A
AC23A
AC21A
AC22A
AC23A
AC21A
AC22A
AC23A
AC21A/B
AC22A/B
AC23A
AC21A/AC22A
AC23A AC21A/AC22A AC23A
630
630
630
630
630
800
800
800
800
800
800
800
800
800
800
800
800
800
800
800
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1250
1250
1250
1250
1250
1250
1250
1250
1250
1250
1250
1250
1250
1250
1250
1450/1600
1450/1600
1250/1600
1250/1600
1250/1600
1450/1600
1450/1600
1250/1600
1250/1600
1250/1600
1250
1250
1250
1250
1250
2000
2000
2000
2000
2000
–
–
–
–
–
DC21A/DC23A
DC21A
DC22A
DC23A
DC21A
DC22A
DC23A
DC21A
DC22A
DC23A
DC21A/B
DC22A
DC23A
DC21A/DC22A
DC23A DC21A/DC22A DC23A
630/2
630/4
800/2 800/2 800/2 1000/2 1000/2 1000/2 1250/2 1250/2 1250/2 1600/1600/2 1600/1600/2 1250/2 2000/2
800/4 800/4 800/4 1000/4 1000/4 1000/4 1250/4 1250/4 1250/4 1450/1600/4 1450/1600/4 1250/4 2000/4
200
200
315
400
375
400
560
b
class 120 - 60 %
105
330
50
35
20
20
8
b
5000
250
220
400
500
500
560
710
b
class 120 - 60 %
105
330
50
35
20
10
8
b
3000
315
250
560
630
600
710
900
b
class 120 - 60 %
105
330
50
35
20
10
8
b
3000
AC21A/AC23A
1000
1000
1000
1000
1000
AC21A
500
500
500
500
500
AC23A
500
500
500
500
500
AC21A
500
500
500
500
500
AC22A
500
500
500
500
500
AC23A
500
500
500
500
500
AC22A
500
500
500
500
500
AC23A
500
500
500
500
500
AC21A/B
500/100
500/100
500/100
500/100
500/100
AC22A/B
500/100
500/100
500/100
500/100
500/100
DC21A/DC23A
1000
1000
b
–
b
III
DC21A DC22A DC23A
500
500
500
500
500
500
b
–
b
III
DC21A
500
500
b
–
b
III
DC22A
500
500
DC23A DC21A DC22A
500
500
500
500
500
500
b
–
b
III
DC23A
500
500
DC21A
500
500
b
–
b
III
DC22A
500
500
–
–
–
Schneider Electric
AC22A
500
500
500
500
500
400
375
710
800
750
900
900
b
class 120 - 60 %
105
105
50
35
20
10
8
b
3000
AC21A
500
500
500
500
500
–
400
375
710
800
750
900
900
b
class 120 - 60 %
105
105
50
35
20
10
8
b
3000
–
–
–
2500
2500
2500
2500
2500
2500/2
2500/4
–
–
–
–
–
–
–
–
–
–
–
–
–
–
b
class 120 - 60 %
105
105
50
50
30
13
11
b
3000
–
–
–
–
–
–
–
b
class 120 - 60 %
105
105
50
50
30
13
11
b
3000
AC23A
500
500
500
500
500
AC21A/AC22A
500
500
500
500
500
AC21A/AC22A
500
500
500
500
500
DC23A
500
500
DC21A/DC22A
500
500
b
–
–
III
DC21A/DC22A
500
500
b
–
–
III
–
–
29
Switch-disconnector selection (cont.)
Interpact INS630b to 2500 (cont.)
Functions and
characteristics
Interpact INS switch-disconnectors
Installation
Fixed, front connection
Fixed, rear connection
On symmetrical rails
On a backplate
Connection
By cables
By cables with lugs
Flat-facing bars
Edgewise bars
to bare cable connectors
directly to terminals
to spreaders
to vertical-connection adapters via cable-lug adapters
directly to terminals
to spreaders
to vertical-connection adapters
Indication and measurement auxiliaries
Auxiliary contacts
Voltage-presence indicator
Current-transformer module
Ammeter module
Control, locking and interlocking
Control
Locking
Interlocking
direct front rotary handle
extended front rotary handle
direct lateral rotary handle
extended lateral rotary handle
by keylock
by padlocks
by keylock
mechanical
Complete source-changeover assembly
Operating torque (Nm) (typical value for 3/4 poles with front handle)
Installation and connection accessories
Bare cable connectors
Rear connectors
Terminal extensions
Spreaders
One-piece spreader
Terminal shrouds
Terminal shields
Interphase-barrier
Front panel escutcheons
Coupling accessories
Tightening torque for electrical connections (Nm)
Dimensions and weights
Overall dimensions H x W x D (mm)
Approximate weight (kg)
3 poles
4 poles
3 poles
4 poles
Enclosure dimensions for Ithe
E90489
H x W x D (mm)
H
D
30
W
Schneider Electric
Switch-disconnector selection (cont.)
Interpact INS630b to 2500 (cont.)
Functions and
characteristics
INS630b
INS800
INS1000
INS1250
INS1600
INS2000
INS2500
b
b
–
b
b
b
–
b
b
b
–
b
b
b
–
b
b
b
–
b
b
b
–
b
b
b
–
b
–
–
–
b
b
b
b
–
–
–
b
b
b
b
–
–
–
b
b
b
b
–
–
–
b
b
b
b
–
–
–
b
b
b
b
–
b
–
–
b
–
–
–
b
–
–
b
–
–
b
–
–
–
b
–
–
–
b
–
–
–
b
–
–
–
b
–
–
–
b
–
–
–
b
–
–
–
b
b
–
–
b
b
b
–
–
30
b
b
–
–
b
b
b
–
–
30
b
b
–
–
b
b
b
–
–
30
b
b
–
–
b
b
b
–
–
30
b
b
–
–
b
b
b
–
–
30
b
b
–
–
b
b
b
–
–
60
b
b
–
–
b
b
b
–
–
60
–
–
b
b
–
–
b
b
b
–
50
–
–
b
b
–
–
b
b
b
–
50
–
–
b
b
–
–
b
b
b
–
50
–
–
b
b
–
–
b
b
b
–
50
–
–
b
b
–
–
b
b
b
–
50
–
–
b
b
–
–
b
b
b
–
50
–
–
b
b
–
–
b
b
b
–
50
340 x 300 x 198
410 x 300 x 198
14
18
340 x 300 x 198
410 x 300 x 198
14
18
340 x 300 x 198
410 x 300 x 198
14
18
340 x 300 x 198
410 x 300 x 198
14
18
340 x 300 x 198
410 x 300 x 198
14
18
348 x 440 x 325
463 x 440 x 325
35
45
348 x 440 x 325
463 x 440 x 325
35
45
??? x ??? x ???
??? x ??? x ???
??? x ??? x ???
??? x ??? x ???
??? x ??? x ???
??? x ??? x ???
??? x ??? x ???
Schneider Electric
31
Functions and
characteristics
Switch-disconnector selection
Interpact INV100 to 630
056650_A
Interpact INV switch-disconnectors
Number of poles
Electrical characteristics as defined by IEC 60947-1 / 60947-3 and EN 60947-1 / 60947-3
Conventional thermal current (A)
Conventional thermal current
in enclosure
Rated insulation level (V)
Impulse-withstand voltage (kV)
Rated operational voltage (V)
Ith
Ithe
at 60 °C
at 60 °C
Ui
Uimp
Ue
AC 50/60 Hz
Rated operational voltage AC20 and DC20 (V)
AC 50/60 Hz
DC
AC 50/60 Hz
Rated operational current (A)
Electrical AC
Ie
Interpact INV250 switch-disconnector
50/60 Hz
220-240 V
380-415 V
440-480 V (1)
500-525 V
660-690 V
Electrical DC
056654_A
125 V (2P in series)
250 V (4P in series)
Rated operational power AC23 (kW)
Electrical AC
Rated duties
uninterrupted duty
intermittent duty
min. (switch-disconnector alone)
max. (with upstream protection circuit breaker)
1s
3s
20 s
30 s
Short-circuit making capacity
Short-time withstand current
Icm
(kA peak)
Icw (A rms)
Interpact INV250 emergency-off switch-disconnector
Suitability for isolation
Durability (category A) (O - C-O cycles)
50/60 Hz
220-240 V
230 V (NEMA)
380-415 V
440 V
480 V (NEMA)
500-525 V
660-690 V
Mechanical
Electrical AC
50/60 Hz
440 V
500 V
690 V
Electrical DC
250 V
Positive contact indication
Visible break
Emergency-off switch disconnector
Degree of pollution
Upstream protection
See the “Additional characteristics” section, 308E5015
(1) Suitable for 480 V NEMA.
(2) 550 A (DC).
32
Schneider Electric
Switch-disconnector selection (cont.)
Interpact INV100 to 630 (cont.)
Functions and
characteristics
INV100
INV160
INV200
INV250
INV320
INV400
INV500
INV630
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
100
100
160
160
200
200
250
250
320
320
400
400
500
500
630
630 (2)
750
8
690
250
750
750
8
690
250
750
750
8
690
250
750
750
8
690
250
750
750
8
690
250
750
750
8
690
250
750
750
8
690
250
750
750
8
690
250
750
AC21A
100
100
100
100
100
AC22A
100
100
100
100
100
AC23A
100
100
100
100
100
AC21A
160
160
160
160
160
AC22A
160
160
160
160
160
AC23A
160
160
160
160
160
AC21A
200
200
200
200
200
AC22A
200
200
200
200
200
AC23A
200
200
200
200
200
AC21A
250
250
250
250
250
AC22A
250
250
250
250
250
AC23A
250
250
250
200
200
AC21A
320
320
320
320
320
AC22A
320
320
320
320
320
AC23A
320
320
320
320
320
AC21A
400
400
400
400
400
AC22A
400
400
400
400
400
AC23A
400
400
400
400
400
AC21A
500
500
500
500
500
AC22A
500
500
500
500
500
AC23A
500
500
500
500
500
AC21A
630
630
630
630
630
AC22A
630
630
630
630
550
AC23A/B
630/630
630/630
630/630
500/630
500/630
DC21A DC22A DC23B DC21A DC22A DC23B DC21A DC22A DC23B DC21A DC22A DC23B DC21A DC22A DC23A DC21A DC22A DC23A DC21A DC22A DC23A DC21A DC22A DC23A/B
100 100 100 160 160 160 200 200 200 250 250 200 320 320 320 400 400 400 500 500 500 550 550 550/630
100 100 100 160 160 160 200 200 200 250 250 200 320 320 320 400 400 400 500 500 500 550 550 550/630
22
22
45
55
55
55
55
b
class 120 - 60 %
30
330
8500
4900
2200
1800
b
15000
45
45
75
90
50
110
90
b
class 120 - 60 %
30
330
8500
4900
2200
1800
b
15000
55
55
90
110
110
132
160
b
class 120 - 60 %
30
330
8500
4900
2200
1800
b
15000
75
75
132
150
150
132
160
b
class 120 - 60 %
30
330
8500
4900
2200
1800
b
15000
90
90
160
185
185
220
250
b
class 120 - 60 %
50
330
20000
11500
4900
4000
b
10000
110
110
200
220
220
250
400
b
class 120 - 60 %
50
330
20000
11500
4900
4000
b
10000
132
150
250
250
250
355
500
b
class 120 - 60 %
50
330
20000
11500
4900
4000
b
10000
200
200
315
400
375
400
560
b
class 120 - 60 %
50
330
20000
11500
4900
4000
b
10000
AC22A
1500
1500
1500
AC22A
1500
1500
1500
AC22A
1500
1500
1500
AC22A
1500
1500
1500
AC21A
1000
1000
1000
AC21A
1000
1000
1000
AC21A
1000
1000
1000
AC21A
1000
1000
1000
AC23A
1500
1500
1500
AC23A
1500
1500
1500
AC23A
1500
1500
1500
AC23A
1500
1500
1500
AC22A
1000
1000
1000
AC23A
1000
1000
1000
AC22A
1000
1000
1000
AC23A
1000
1000
1000
AC22A
1000
1000
1000
AC23A
1000
1000
1000
AC22A
1000
1000
1000
AC23A/B
1000/–
1000/–
1000/200
DC22A DC23A
1500 1500
b
b
b
III
DC22A DC23A
1500 1500
b
b
b
III
DC22A DC23A
1500 1500
b
b
b
III
DC22A DC23A
1500 1500
b
b
b
III
DC21A DC22A DC23A DC21A DC22A DC23A DC21A DC22A DC23A DC21A DC22A DC23A/B
1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000/200
b
b
b
b
b
b
b
b
b
b
b
b
III
III
III
III
–
–
–
–
–
Schneider Electric
–
–
–
33
Switch-disconnector selection (cont.)
Interpact INV100 to 630 (cont.)
Functions and
characteristics
Interpact INV switch-disconnectors
Installation
Fixed, front connection
Fixed, rear connection
On symmetrical rails
On a backplate
Connection
By cables
By cables with lugs
Flat-facing bars
Edgewise bars
to bare cable connectors
directly to terminals
to spreaders
to vertical-connection adapters via cable-lug adapters
directly to terminals
to spreaders
to vertical-connection adapters
Indication and measurement auxiliaries
Auxiliary contacts
Voltage-presence indicator
Current-transformer module
Ammeter module
Control, locking and interlocking
Control
Locking
Interlocking
direct front rotary handle
extended front rotary handle
direct lateral rotary handle
extended lateral rotary handle
by keylock
by padlocks
by keylock
mechanical
Complete source-changeover assembly
Operating torque (Nm) (typical value for 3/4 poles with front handle)
Installation and connection accessories
Bare cable connectors
Rear connectors
Terminal extensions
Spreaders
One-piece spreader
Terminal shrouds
Terminal shields
Interphase-barrier
Front panel escutcheons
Coupling accessories
Tightening torque for electrical connections (Nm)
Dimensions and weights
Overall dimensions H x W x D (mm)
Approximate weight (kg)
3 poles
4 poles
3 poles
4 poles
Enclosure dimensions for Ithe
E90489
H x W x D (mm)
H
D
34
W
Schneider Electric
Switch-disconnector selection (cont.)
Interpact INV100 to 630 (cont.)
Functions and
characteristics
INV100
INV160
INV200
INV250
INV320
INV400
INV500
INV630
b
b
–
b
b
b
–
b
b
b
–
b
b
b
–
b
b
b
–
b
b
b
–
b
b
b
–
b
b
b
–
b
b
b
b
–
b
b
–
b
b
b
–
b
b
–
b
b
b
–
b
b
–
b
b
b
–
b
b
–
b
b
b
–
b
b
b
b
b
b
–
b
b
b
b
b
b
–
b
b
b
b
b
b
–
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
–
5 < C < 6.2
b
b
b
b
b
b
b
b
–
5 < C < 6.2
b
b
b
b
b
b
b
b
–
5 < C < 6.2
b
b
b
b
b
b
b
b
–
5 < C < 6.2
b
b
–
–
b
b
b
b
–
13.5 < C < 16.5
b
b
–
–
b
b
b
b
–
13.5 < C < 16.5
b
b
–
–
b
b
b
b
–
13.5 < C < 16.5
b
b
–
–
b
b
b
b
–
13.5 < C < 16.5
b
b
b
b
b
–
b
b
b
b
15
b
b
b
b
b
–
b
b
b
b
15
b
b
b
b
b
–
b
b
b
b
15
b
b
b
b
b
–
b
b
b
b
15
b
b
b
b
b
–
b
b
b
b
50
b
b
b
b
b
–
b
b
b
b
50
b
b
b
b
b
–
b
b
b
b
50
b
b
b
b
b
–
b
b
b
b
50
140 x 136 x 86
140 x 136 x 86
2
2.2
140 x 136 x 86
140 x 136 x 86
2
2.2
140 x 136 x 86
140 x 136 x 86
2
2.2
140 x 136 x 86
140 x 136 x 86
2
2.2
185 x 205 x 120
185 x 205 x 120
4.6
4.9
185 x 205 x 120
185 x 205 x 120
4.6
4.9
185 x 205 x 120
185 x 205 x 120
4.6
4.9
185 x 205 x 120
185 x 205 x 120
4.6
4.9
300 x 400 x 200
300 x 400 x 200
300 x 400 x 200
300 x 400 x 200
400 x 600 x 200
400 x 600 x 200
400 x 600 x 200
400 x 600 x 200
Schneider Electric
35
E00000
Functions and
characteristics
Switch-disconnector selection (cont.)
Interpact INV630b to 2500
Interpact INV switch-disconnectors
Number of poles
Nouvelle photo à venir
Electrical characteristics as defined by IEC 60947-1 / 60947-3 and EN 60947-1 / 60947-3
Conventional thermal current (A)
Conventional thermal current
in enclosure
Rated insulation level (V)
Impulse-withstand voltage (kV)
Rated operational voltage (V)
Ith
Ithe
at 60 °C
at 60 °C
Ui
Uimp
Ue
AC 50/60 Hz
AC 50/60 Hz
DC
Rated operational voltage AC20 and DC20 (V)
Rated operational current (A)
Ie
Electrical AC
50/60 Hz
220-240 V
380-415 V
440-480 V (1)
500-525 V
660-690 V
Electrical DC
125 V (2P in series)
250 V (4P in series)
Interpact INV800 switch-disconnector
Electrical AC
Rated duties
uninterrupted duty
intermittent duty
min. (switch-disconnector alone)
max. (with upstream protection circuit breaker)
0.5 s
1s
3s
20 s
30 s
E00000
Rated operational power AC23 (kW)
Nouvelle photo à venir
Short-circuit making capacity
Short-time withstand current
Suitability for isolation
Durability (category A) (O - C-O cycles)
Icm
(kA peak)
Icw (A rms)
50/60 Hz
220-240 V
230 V (NEMA)
380-415 V
440 V
480 V (NEMA)
500-525 V
660-690 V
Mechanical
Electrical AC
Interpact INV800 emergency-off switch-disconnector
50/60 Hz
220-240 V
380-415 V
440-480 V (1)
500-525 V
660-690 V
Electrical DC
125 V / 2 pôles
250 V / 4 pôles
Positive contact indication
Visible break
Emergency-off switch disconnector
Degree of pollution
Upstream protection
See the “Additional characteristics” section, 308E5025 and 308E5030
(1) Suitable for 480 V NEMA.
(2) For vertical connection busbars only; for horizontal
connection busbars, see derating chart in "Installation
recommendations".
36
Schneider Electric
Switch-disconnector selection (cont.)
Interpact INV630b to 2500 (cont.)
Functions and
characteristics
INV630b
INV800
INV1000
INV1250
INV1600
INV2000
INV2500
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
630
630
800
800
1000
1000
1250
1250
1600 (2)
1600 (2)
2000
2000
2500
2500
1000
12
690
250
1000
1000
12
690
250
1000
1000
12
690
250
1000
1000
12
690
250
1000
1000
12
690
250
1000
1000
12
690
250
1000
1000
12
690
250
1000
AC21A/AC22A/AC23B
630
630
630
630
630
AC21A/AC22A/AC23B
800
800
800
800
800
AC21A/AC22A/AC23B
1000
1000
1000
1000
1000
AC21A/AC22A/AC23B
1250
1250
1250
1250
1250
AC21A/B-AC22A/B
1450/1600
1450/1600
1250/1600
1250/1600
1250/1600
AC23B
1250
1250
1250
1250
1250
AC21A/AC22A
2000
2000
2000
2000
2000
AC23B
–
–
–
–
–
AC21A/AC22A
2500
2500
2500
2500
2500
DC21A/DC22A/DC23B
630/2
630/4
DC21A/DC22A/DC23B
800/2
800/4
DC21A/DC22A/DC23B
1000/2
1000/4
DC21A/DC22A/DC23B
1250/2
1250/4
DC21A/DC22A
1600/1600/2
1450/1600/4
DC23B
1250/2
1250/4
DC21A/DC22A
2000/2
2000/4
DC23B
–
–
DC21A/DC22A DC23B
2500/2
–
2500/4
–
200
200
315
400
375
400
560
b
class 120 - 60 %
105
330
50
35
20
10
8
b
5000
250
220
400
500
300
560
710
b
class 120 - 60 %
105
330
50
35
20
10
8
b
3000
315
250
560
630
600
710
900
b
class 120 - 60 %
105
330
50
35
20
10
8
b
3000
400
375
710
800
750
900
900
b
class 120 - 60 %
105
105
50
35
20
10
8
b
3000
400
375
710
800
750
900
900
b
class 120 - 60 %
105
105
50
35
20
10
8
b
3000
AC21A/AC22A
1000
1000
1000
1000
1000
AC23B
200
200
200
200
200
AC21A/AC22A
500
500
500
500
500
AC21A/AC22A
500
500
500
500
500
AC21A/AC22A
500
500
500
500
500
AC21A/B-AC22A/B
500/100
500/100
500/100
500/100
500/100
DC21A/DC22A
1000
1000
b
b
b
III
DC23B
200
200
DC21A/DC22A DC23B DC21A/DC22A DC23B DC21A/DC22A DC23B DC21A/DC22A
500
100
500
100
500
100
500
500
100
500
100
500
100
500
b
b
b
b
b
b
b
b
b
b
b
b
III
III
III
III
–
Schneider Electric
–
AC23B
100
100
100
100
100
–
AC23B
100
100
100
100
100
–
AC23B
100
100
100
100
100
–
AC23B
–
–
–
–
–
–
–
–
–
–
–
–
b
class 120 - 60 %
105
105
50
50
30
13
11
b
3000
–
–
–
–
–
–
–
b
class 120 - 60 %
105
105
50
50
30
13
11
b
3000
AC23B
100
100
100
100
100
AC21A/AC22A
500
500
500
500
500
AC23B
–
–
–
–
–
AC21A/AC22A
500
500
500
500
500
DC23B
100
100
DC21A/DC22A
500
500
b
b
–
III
DC23B
–
–
DC21A/DC22A DC23B
500
–
500
–
b
b
–
III
–
AC23B
–
–
–
–
–
–
37
Switch-disconnector selection (cont.)
Interpact INV630b to 2500 (cont.)
Functions and
characteristics
Interpact INV switch-disconnectors
Installation
Fixed, front connection
Fixed, rear connection
On symmetrical rails
On a backplate
Connection
By cables
By cables with lugs
Flat-facing bars
Edgewise bars
to bare cable connectors
directly to terminals
to spreaders
to vertical-connection adapters via cable-lug adapters
directly to terminals
to spreaders
to vertical-connection adapters
Indication and measurement auxiliaries
Auxiliary contacts
Voltage-presence indicator
Current-transformer module
Ammeter module
Control, locking and interlocking
Control
Locking
Interlocking
direct front rotary handle
extended front rotary handle
direct lateral rotary handle
extended lateral rotary handle
by keylock
by padlocks
by keylock
mechanical
Complete source-changeover assembly
Operating torque (Nm) (typical value for 3/4 poles with front handle)
Installation and connection accessories
Bare cable connectors
Rear connectors
Terminal extensions
Spreaders
One-piece spreader
Terminal shrouds
Terminal shields
Interphase-barrier
Front panel escutcheons
Coupling accessories
Tightening torque for electrical connections (Nm)
Dimensions and weights
Overall dimensions H x W x D (mm)
Approximate weight (kg)
3 poles
4 poles
3 poles
4 poles
Enclosure dimensions for Ithe
E90489
H x W x D (mm)
H
D
38
W
Schneider Electric
Switch-disconnector selection (cont.)
Interpact INV630b to 2500 (cont.)
Functions and
characteristics
INV630b
INV800
INV1000
INV1250
INV1600
INV2000
INV2500
b
b
–
b
b
b
–
b
b
b
–
b
b
b
–
b
b
b
–
b
b
b
–
b
b
b
–
b
–
–
–
b
b
b
b
–
–
–
b
b
b
b
–
–
–
b
b
b
b
–
–
–
b
b
b
b
–
–
–
b
b
b
b
–
b
–
–
b
–
–
–
b
–
–
b
–
–
b
–
–
–
b
–
–
–
b
–
–
–
b
–
–
–
b
–
–
–
b
–
–
–
b
–
–
–
b
b
–
–
b
b
b
–
–
30
b
b
–
–
b
b
b
–
–
30
b
b
–
–
b
b
b
–
–
30
b
b
–
–
b
b
b
–
–
30
b
b
–
–
b
b
b
–
–
30
b
b
–
–
b
b
b
–
–
60
b
b
–
–
b
b
b
–
–
60
–
–
b
b
–
–
b
b
b
–
50
–
–
b
b
–
–
b
b
b
–
50
–
–
b
b
–
–
b
b
b
–
50
–
–
b
b
–
–
b
b
b
–
50
–
–
b
b
–
–
b
b
b
–
50
–
–
b
b
–
–
b
b
b
–
50
–
–
b
b
–
–
b
b
b
–
50
340 x 300 x 198
410 x 300 x 198
14
18
340 x 300 x 198
410 x 300 x 198
14
18
340 x 300 x 198
410 x 300 x 198
14
18
340 x 300 x 198
410 x 300 x 198
14
18
340 x 300 x 198
410 x 300 x 198
14
18
348 x 440 x 325
463 x 440 x 325
35
45
348 x 440 x 325
463 x 440 x 325
35
45
??? x ??? x ???
??? x ??? x ???
??? x ??? x ???
??? x ??? x ???
??? x ??? x ???
??? x ??? x ???
??? x ??? x ???
Schneider Electric
39
E00000
Functions and
characteristics
Complete source-changeover
assembly selection
Interpact INS250-100 to 630 (cont.)
Interpact INS switch-disconnectors
Number of poles
Nouvelle photo à venir
Electrical characteristics as defined by IEC 60947-1 / 60947-3 and EN 60947-1 / 60947-3
Conventional thermal current (A)
Conventional thermal current
in enclosure
Rated insulation level (V)
Impulse-withstand voltage (kV)
Rated operational voltage (V)
Ith
Ithe
at 60 °C
at 60 °C
Ui
Uimp
Ue
AC 50/60 Hz
Rated operational voltage AC20 and DC20 (V)
AC 50/60 Hz
DC
AC 50/60 Hz
Rated operational current (A)
Electrical AC
Ie
50/60 Hz
220-240 V
380-415 V
440-480 V (1)
500-525 V
660-690 V
Electrical DC
Complete assembly ????
125 V (2P in series)
250 V (4P in series)
E00000
Rated duties
Short-circuit making capacity
Nouvelle photo à venir
Short-time withstand current
Icm
(kA peak)
Icw (A rms)
Suitability for isolation
Durability (category A) (O - C-O cycles)
uninterrupted duty
intermittent duty
min. (switch-disconnector alone)
max. (with upstream protection circuit breaker)
1s
3s
20 s
30 s
Mechanical
Electrique AC
50/60 Hz
440 V
500 V
690 V
Electrique DC
250 V
Positive contact indication
Visible break
Emergency-off switch disconnector
Degree of pollution
Complete assembly ????
Upstream protection
See the “Additional characteristics” section, 308E5015
(1) Suitable for 480 V NEMA.
40
Schneider Electric
Complete source-changeover
assembly selection (cont.)
Interpact INS250-100 to 630 (cont.)
Functions and
characteristics
INS250-100 INS250-160 INS250-200 INS250
INS320
INS400
INS500
INS630
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
100
100
160
160
200
200
250
250
320
320
400
400
500
500
630
630
750
8
690
250
750
750
8
690
250
750
750
8
690
250
750
750
8
690
250
750
750
8
690
250
750
750
8
690
250
750
750
8
690
250
750
750
8
690
250
750
AC22A
100
100
100
100
100
AC23A
100
100
100
100
100
AC22A
160
160
160
160
160
AC23A
160
160
160
160
160
AC22A
200
200
200
200
200
AC23A
200
200
200
200
200
AC22A
250
250
250
250
250
AC23A
250
250
250
250
250
AC22A
320
320
320
320
320
AC23A
320
320
320
320
320
AC22A
400
400
400
400
400
AC23A
400
400
400
400
400
AC22A
500
500
500
500
500
AC23A
500
500
500
500
500
AC22A
630
630
630
630
630
AC23A
630
630
630
630
630
DC22A DC23A
100
100
100
100
b
class 120 - 60 %
30
330
8500
4900
2200
1800
b
15000
DC22A DC23A
160
160
160
160
b
class 120 - 60 %
30
330
8500
4900
2200
1800
b
15000
DC22A DC23A
200
200
200
200
b
class 120 - 60 %
30
330
8500
4900
2200
1800
b
15000
DC22A DC23A
250
250
250
250
b
class 120 - 60 %
30
330
8500
4900
2200
1800
b
15000
DC22A DC23A
320
320
320
320
b
class 120 - 60 %
50
330
20000
11500
4900
4000
b
10000
DC22A DC23A
400
400
400
400
b
class 120 - 60 %
50
330
20000
11500
4900
4000
b
10000
DC22A DC23A
500
500
500
500
b
class 120 - 60 %
50
330
20000
11500
4900
4000
b
10000
DC22A DC23A/B
550
550/630
550
550/630
b
class 120 - 60 %
50
330
20000
11500
4900
4000
b
10000
AC22A
1500
1500
1500
AC23A
1500
1500
1500
AC22A
1500
1500
1500
AC23A
1500
1500
1500
AC22A
1500
1500
1500
AC23A
1500
1500
1500
AC22A
1500
1500
1500
AC23A
1500
1500
1500
AC22A
1500
1500
1500
AC22A
1500
1500
1500
AC22A
1500
1500
1500
AC22A
1500
1500
1500
DC22A
1500
b
–
–
III
DC23A
1500
DC22A
1500
b
–
–
III
DC23A
1500
DC22A
1500
b
–
–
III
DC23A
1500
DC22A
1500
b
–
–
III
DC23A
1500
DC23A/B
1000/–
b
–
–
III
DC23A/B
1000/–
b
–
–
III
DC23A/B
1000/–
b
–
–
III
DC23A/B
1000/200
b
–
–
III
–
–
–
–
–
Schneider Electric
–
–
–
AC23A
1500
1500
1500
AC23A
1500
1500
1500
AC23A
1500
1500
1500
AC23A
1500
1500
1500
41
Functions and
characteristics
Complete source-changeover
assembly selection (cont.)
Interpact INS250-100 to 630 (cont.)
Interpact INS switch-disconnectors
Installation and connection
Fixed, front connection
Fixed, rear connection
On symmetrical rails
On a backplate
Connection
By cables
By cables with lugs
Flat-facing bars
Edgewise bars
to bare cable connectors
directly to terminals
to spreaders
to vertical-connection adapters via cable-lug adapters
directly to terminals
to spreaders
to vertical-connection adapters
Indication and measurement auxiliaries
Auxiliary contacts
Voltage-presence indicator
Current-transformer module
Ammeter module
Control, locking and interlocking
Control
Locking
direct front rotary handle
extended front rotary handle
direct lateral rotary handle
extended lateral rotary handle
by keylock
by padlocks
Complete source-changeover assembly
Operating torque (Nm) (typical value for 3/4 poles with front handle)
Installation and connection accessories
Bare cable connectors
Rear connectors
Terminal extensions
Spreaders
One-piece spreader
Terminal shrouds
Terminal shields
Interphase-barrier
Front panel escutcheons
Coupling accessories
Tightening torque for electrical connections (Nm)
Dimensions and weights
Overall dimensions H x W x D (mm)
Approximate weight (kg)
42
3 poles
4 poles
3 poles
4 poles
Schneider Electric
Complete source-changeover
assembly selection (cont.)
Interpact INS250-100 to 630 (cont.)
Functions and
characteristics
INS250-100 INS250-160 INS250-200 INS250
INS320
NS400
INS500
INS630
b
b
–
b
b
b
–
b
b
b
–
b
b
b
–
b
b
b
–
b
b
b
–
b
b
b
–
b
b
b
–
b
b
b
b
–
b
b
–
b
b
b
–
b
b
–
b
b
b
–
b
b
–
b
b
b
–
b
b
–
b
b
b
–
b
b
b
b
b
b
–
b
b
b
b
b
b
–
b
b
b
b
b
b
–
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
–
–
b
b
b
5 < C < 6.2
b
b
–
–
b
b
b
5 < C < 6.2
b
b
–
–
b
b
b
5 < C < 6.2
b
b
–
–
b
b
b
5 < C < 6.2
b
b
–
–
b
b
b
13.5 < C < 16.5
b
b
–
–
b
b
b
13.5 < C < 16.5
b
b
–
–
b
b
b
13.5 < C < 16.5
b
b
–
–
b
b
b
13.5 < C < 16.5
b
b
–
b
–
–
b
b
–
b
15
b
b
–
b
–
–
b
b
–
b
15
b
b
–
b
–
–
b
b
–
b
15
b
b
–
b
–
–
b
b
–
b
15
b
b
–
b
–
–
b
b
–
b
50
b
b
–
b
–
–
b
b
–
b
50
b
b
–
b
–
–
b
b
–
b
50
b
b
–
b
–
–
b
b
–
b
50
140 x 136 x 86
140 x 136 x 86
6.4
6.4
140 x 136 x 86
140 x 136 x 86
6.4
6.4
140 x 136 x 86
140 x 136 x 86
6.4
6.4
140 x 136 x 86
140 x 136 x 86
6.4
6.4
185 x 205 x 120
185 x 205 x 120
13.5
???
185 x 205 x 120
185 x 205 x 120
13.5
???
185 x 205 x 120
185 x 205 x 120
13.5
???
185 x 205 x 120
185 x 205 x 120
13.5
13.5
Schneider Electric
43
052760_A
Functions and
characteristics
Installation
Interpact INS and INV switch-disconnectors offer a number of rational installation
solutions to optimise available space inside enclosures. They may be installed in
individual enclosures or as incomers in power distribution or control panels.
b Interpact INS40 to 160 switch-disconnectors have a standard 45 mm high front
and may be clipped onto a Multifix or symmetrical rail. They may be installed in all
Multi 9 modular enclosures, including Pragma, Prisma, etc.
b Interpact INS250 to 630 and INV100 to 630 switch-disconnectors may be
installed on mounting plates or rails. Installation as incomers in Prisma power
distribution cubicles is very flexible:
v the mounting plates are the same as those used for Compact NS circuit breakers
and are identical for direct and extended handles
v installation in 300 mm ducts is possible for ratings up to 630 A.
Local isolation enclosure
b each individual enclosure includes:
v a door with a cut-out
v a mounting plate
v accessories required for extended front or lateral
rotary handle
v removable plates (without holes) for cable entry.
The Interpact INS switch-disconnector must be order
separately.
E90491
E56047_A
Individual enclosures
Heavy-duty individual
enclosure (sheet metal or
plastic)
056699_A
Power distribution incomer in a Prisma cubicle
b the enclosures in the Pragma range are:
v made of self-extinguishing insulating material
v supplied with all accessories (terminal blocks,
blanking plates, etc.)
v rated class 2.
E54453
Pragma modular enclosures
Interpact INS40 on a
symmetrical rail
b the metal cubicles and enclosures in the Prisma
range are highly adaptable to the type of installation:
v basic cubicle or enclosure
v multifix rail
v modular front plates
v distribution accessories
v ducts for running cables or installing terminals
v plain or transparent doors.
E54454
Prisma metal cubicles and enclosures
Installation in a 300 mm
duct
Power distribution incomer in a Prisma GK cubicle
44
Schneider Electric
Connection
Interpact INS40 to 160
E92189
Functions and
characteristics
Terminal shields
Sealable long terminal
shield
Terminal shroud
Interphase
barrier
Auxiliary contact
Extended lateral
control
Interpact
INS40 to 160
Lateral control
on functional
enclosure
Lateral rotary
control
ON
ON
I
I
OFF
Emergency-off
Distribution
connector
1-cable
connector
OFF
0
Extended rotary
control
0
Emergency-off
extended rotary
control
E39432
.2
.1
E38888
Interpact INS40 to INS80 switch-disconnectors are
equipped as standard with connectors for bare copper
or aluminium cables.
Distribution connector
This connector screws directly into the switchdisconnector terminals for connection of three cables
of the following types:
b 1 to 10 mm2 flexible cables (1)
b 1.5 to 16 mm2 rigid cables.
.4
E54455
Interpact INS40 to INS80
N
E54456
Connection of bars or cables with lugs
Interpact INS100 to INS160 switch-disconnectors are
equipped as standard with terminals comprising nuts
with M6 screws for direct connection of insulated bars
or cables with lugs.
Lugs
The special lugs for copper cables may be used for
cables with cross-sectional areas up to 95 mm2.
Secure the lugs by hexagonal crimping or punching.
Lugs are supplied with interphase-barrier and are
compatible with the terminal shields.
.1
N
E38889
E54463
Interpact INS100 to INS160
Lug for copper cable
E30707
b 1-cable connectors for Interpact INS100/125/160 snap
directly onto the terminals, for cables 1.5 to 95 mm2 (1).
b distribution connectors are designed for four cables
with cross-section areas 1.5 to 25 mm2 rigid or 1.5 to
16 mm2 flexible (1). They screw directly to the
terminals. The interphase-barrier supplied with the
distribution connectors may be replaced by long
terminal shields.
E32424
.2
.1
E32423
.4
E54457
Connection of bare cables (Cu or Al)
1-cable
connector
Distribution
connector
N
(1) Connection of 1.5 to 4 mm2 flexible cables requires
crimped or auto-crimping ferrules.
Schneider Electric
45
Electrical and mechanical
accessories
Interpact INS250
Interpact INV100 to 250
E72527
Functions and
characteristics
E72527
Sealable long terminal shield
for spreaders
One-piece spreader
Interphase
barrier
I
ON
Spreader
Handle
support
Rear connections
I
ON
OFF
O
OFF
O
Interpact
INS250
Extended lateral
rotary control
Emergency-off
extended
rotary control
Direct lateral
rotary control
I
ON
O
OFF
Locking by
keylock
I
ON
O
OFF
Lateral rotary
control
Auxiliary
contacts
Visible break (INV)
ON
I
OFF
ON
Current transformer
module
Emergency-off
extended rotary control
0
I
OFF
0
I
ON
O
OFF
Escutcheon
Emergency-off
Ammeter module
16
A
12
8
4
0
160/5
Coupling accessory
46
Sealable short
terminal shield
Schneider Electric
Electrical and mechanical
accessories (cont.)
Interpact INS320 to 630
Interpact INV320 to 630
E92190
Functions and
characteristics
Sealable long
terminal shield
Bare cable
connectors
Spreader
Right-angle
terminal
extension
Edgewise
teminal
extension
Interphase
barrier
Rear connections
Interpact
INS400 to 630
Locking
by keylock
Emergency-off
extended rotary
control
Auxiliary
contacts
Extended rotary
control
Visible break (INV)
Current transformer
module
Ammeter module
Emergency-off
Escutcheon
16
A
12
8
4
0
160/5
Sealable short
terminal shield
Coupling accessory
Schneider Electric
47
E18601
Straight terminal extensions
for INS/INV250
Edgewise terminal
extensions for INS/INV320
to 630
Lug for copper cables
E30907
E54460
ø5...8
Right-angle terminal
extensions
E21276
E54459
E54462
ø5...8
Interpact INS250 to INS630 and INV100 to INV630
switch-disconnectors are equipped as standard with
terminals receiving snap-in nuts and screws
(M8 for INS/INV up to 250, M10 from 320 upwards) for
direct connection of insulated bars or cables with lugs.
Terminal extensions (right-angle, edgewise,
spreaders) are available to solve all connection
problems. For Interpact INS/INV630 switchdisconnectors, connection most often requires the
52.5 or 70 mm pitch spreaders.
Lugs
Lugs are different for copper and aluminium cables.
They are supplied with interphase-barrier and are
compatible with the long terminal shields.
b the small lugs for copper cables may be used for
cables with the following cross-sectional areas:
v 120, 150 or 185 mm2 (INS/INV up to 250)
v 240 or 300 mm2 (INS/INV up to 630).
Secure the lugs by hexagonal crimping or punching.
b the small lugs for aluminium cables may be used for
cables with the following cross-sectional areas:
v 150 or 185 mm2 (INS/INV up to 250)
v 240 or 300 mm2 (INS/INV up to 630).
Secure the lugs by hexagonal crimping.
Spreaders
Spreaders increase the pitch of the terminals.
They are not compatible with terminal shields.
The one-piece spreader increases the pitch to
correspond to that of the upstream device and
provides protection against direct contact
(see 308E2060).
E54463
E54456
Front connection of bars or cables
with lugs
E18600
Connection
Interpact INS250 to 630
Interpact INV100 to 630
Functions and
characteristics
ø5...8
E18599
Lug for aluminium cables
E54464
E54461
Spreaders
ø5...8
One-piece spreader
48
Schneider Electric
ø5...8
E54469
1-cable connector for
INS250 and INV100-250
1-cable connector
for INS/INV320 to 630
E54470
E54465
E54466
ø5...8
Bare-cable connectors for Interpact INS/INV switchdisconnectors may be used for both copper and
aluminium cables.
1-cable connectors for Interpact INS250
and INV100 to 250
The connectors snap directly on to the device
terminals or clip onto right-angle and straight terminal
extensions as well as spreaders.
1-cable and 2-cable connectors for Interpact
INS/INV320 to 630
The connectors are screwed to device terminals or
right-angle terminal extensions.
Distribution connectors for Interpact INS250
and INV100 to 250
These connectors are screwed directly to device
terminals. Interphase-barrier are supplied with
distribution connectors, but may be replaced by long
terminal shields. Each connector can receive six
cables with cross-sectional areas ranging from 1.5 to
35 mm2 each.
Polybloc distribution block for Interpact INS250
and INV100 to 250
The Polybloc connects directly to the device terminals
and is used to connect up to six or nine flexible or rigid
cables with cross-sectional areas not exceeding
10 mm2, to each pole. Connection is made to spring
terminals without screws.
2-cable connector
for INS/INV320 to 630
E54471
E54457
Front connection of bare cables
E54468
Connection (cont.)
Interpact INS250 to 630
Interpact INV100 to 630 (cont.)
Functions and
characteristics
E54472
Distribution connector for
INS250 and INV100 to 250
Two lengths
E54467
Rear connections for bars or cables with lugs are
available in two lengths. Bars may be positioned flat,
on edge or at 45° angles depending on how the rear
connections are positioned.
The rear connections are simply fitted to the device
connection terminals. All combinations of rear
connection lengths and positions are possible on a
given switch-disconnector. The switch-disconnector is
mounted on a backplate.
For the connection of cables without lugs, the 1-cable
connectors for Interpact INS250 and INV100 to 250
may be simply clipped onto the rear connections.
E94208
E54456
Rear connection
E54473
Polybloc distribution block for
INS250 and INV100 to 250
Four positions
Schneider Electric
49
Electrical and mechanical
accessories
Interpact INS630b to 2500
Interpact INV630b to 2500
E92191
Functions and
characteristics
Terminal shield
Interphase-barrier
Cable lug adapter
Spreader
Vertical connection
adapter
Base for terminal shield
Interpact
INS800 to 1600
O
OFF
Locking
by keylock
Emergency-off
extended
rotary control
FO
FF
OF
trippe
d
reset
OFF
trippe
Auxiliary contacts
Visible break (INV)
reset
OFF
ON
I
0
d
ON
I
0
Extended rotary
control
OO
OF
OFFF
Escutcheon
Emergency-off (y 1600)
50
Schneider Electric
Functions and
characteristics
Connection
Interpact INS630b to 2500
Interpact INV630b to 2500
Bars
Interpact switch-disconnectors are equipped with
terminals and captive screws for direct connection
of bars.
E88661
E88865
E88887
Direct connection
E88869
Adapters for cables with crimped lugs
Cable-lug adapters are used in conjunction with
vertical connection adapters. They may be used
to connect one to four cables (y 300 mm2)
with crimped lugs.
To ensure adequate mechanical strength, the cablelug adapters must be secured together by spacers.
E88668
E88868
Vertical connection adapters
For connection of edgewise bars.
E88666
E88867
Spreaders
Spreaders increase the pole pitch of a switchdisconnector for greater clearance between the bars.
They are not compatible with terminal shields.
E88663
Connection with accessories
Schneider Electric
51
Connection accessories
Distribution blocks
053997_A
Functions and
characteristics
E54477
Distribloc
3 outgoing
spring terminals
1 to 6 flexible or rigid
Mounting
on backplate
7 outgoing
spring terminals
1 to 4 flexible
or rigid
Clips onto
symmetrical
rail
Distribloc 125 A
E54475
2 outgoing
spring terminals
1 to 10 flexible
1 to 16 rigid
1 incoming
tunnel terminal 35
6 to 35 flexible
10 to 50 rigid
1 outgoing
tunnel terminal 25
4 to 16 flexible
4 to 25 rigid
Modular
cover
Circuit
identification
N
Distribloc is a four-pole distribution block offering:
b 13 outgoing terminals per phase (12 spring terminals and 1 tunnel terminal)
b 1 incoming tunnel terminal for 35 mm2 flexible cable (50 mm2 rigid).
Distribloc exists in two versions:
v Distribloc 125, for switch-disconnectors rated up to 125 A
v Distribloc 160, supplied with prefabricated connections, for direct connection to
switch-disconnectors INS100 to INS160.
Distribloc is supplied with a modular cover that fulfils a number of functions:
b circuit identification: a protected label identifies the various circuits
b aesthetics: the cover has the same design as the associated Interpact INS
switch-disconnector
b user information: all required information is indicated on the cover.
Distribloc can be installed:
b on a symmetrical rail or a backplate
b to the left, the right or under the switch-disconnector, depending on the desired
layout of the switchboard. Installation to the left is particularly useful when the INS
switch-disconnector is equipped with a lateral handle.
Electrical characteristics
b rated short-time withstand current (Icw) = 4.5 kA rms / 1 second.
b rated peak withstand current (Ipk) = 20 kA peak.
b rated insulation voltage (Ui) = 690 V AC.
N
N
041153_A
Multi-stage distribution block 125 A (40°)
b 4 x 10 holes (5 x 10 mm2, 4 x 16 mm2, 1 x 35 mm2)
dimensions: width 88 mm, height 92 mm, depth 51 mm,
distance between fixing centres 68 mm.
b 4 x 17 holes (8 x 10 mm2, 8 x 16 mm2, 1 x 35 mm2)
dimensions: width 125 mm, height 92 mm, depth 51 mm,
distance between fixing centres 105 mm.
v supplied with insulating cover
v easy mounting on Multifix or symmetrical rail
v mounting on slotted plate using screws.
Electrical characteristics
b rated short-time withstand current (Icw) = 3.5 kA rms / 1 second
b rated peak withstand current (Ipk) = 20 kA peak
b rated insulation voltage (Ui) = 500 V AC.
52
Schneider Electric
056384_A
Connection of large cables may require an increase in
the distance between the switch-disconnector terminals.
The one-piece spreader is an accessory that can also be
fitted on Compact NS circuit breakers. It offers the
following features:
b increases the pitch of the switch-disconnector
terminals to correspond to that of the upstream device
b compatible with all the connection and insulation
accessories available for the upstream device
(connectors, terminal extensions, etc.)
b enhances insulation between phases in comparison
with standard spreaders.
One-piece spreader
E54200
Connection accessories (cont.)
One-piece spreader
Functions and
characteristics
INS250
INS320 to 630
INV100 to 250 INV320 to 630
Pitch without
spreaders (mm)
Pitch with
standard
spreaders (mm)
Pitch with
one-piece
spreader (mm)
35
45
45
52.5 or 70
45
–
ø5...8
Mounting
Mounting at the back of a
switchboard
Schneider Electric
Connection and insulation
accessories are identical to
those for Compact NS
E54541
E54548
When equipped with a one-piece spreader, INS and INV
switch-disconnectors may be installed either at the back
of a switchboard or on the front panel with a front
alignment base.
b devices with different frame sizes can thus be
aligned in the switchboard
b the same mounting plate can be used for all devices
(including Compact NS circuit breakers).
Mounting on the front panel
with a front alignment base
53
Connection accessories (cont.)
Insulation of live parts
Terminal shields for INS and INV switchdisconnectors
E54476
Functions and
characteristics
056063_A
Lead-sealable insulation accessories used to protect
against direct contact with power circuits.
b degree of protection: IP40.5
b supplied with lead-sealing accessories.
Interphase-barrier for INS/INV
b safety accessories providing maximum insulation
between the phases of the power connection
b easy installation by snapping into the case
b may be combined with all other connection
accessories, except the terminal shields and terminal
shrouds.
Terminal shields for Interpact
INS and INV
These insulation accessories are used for protection
against direct contact with live connection screws. It is
also possible to attach an insulating plate (not
supplied) to the shrouds to avoid any contact with the
power conductors.
E54542
Terminal shrouds for INS40 to INS160
Spare viewport for Interpact INV switchdisconnectors
Viewports are darkened by the electrical arc. A new
viewport may be installed to maintain the visible-break
function.
E54543
Interphase-barrier for
Interpact INS and INV
.4
.2
.1
N
Ø5
5
88
E51003
Terminal shrouds for
Interpact INS40 to 160
(with insulating plate to avoid
contact with the conductors)
Spare viewport for
Interpact INV
54
Schneider Electric
Auxiliary contacts
044314_A
Functions and
characteristics
Interpact INS and INV
E54504
CAO
or CAF
or OF
N
Ø5
5
8
CAO
or CAF
or OF
Auxiliary contact for Interpact
INS and INV
E54499
Interpact INS40 to 160
ø5...8
Interpact INS250
and INV100 to 250
CAO
or CAF
or OF
One or four common-point changeover contacts can be used to remote switchdisconnector status information for indications, electrical interlocking, relays, etc.
Functions
Each contact may be used for the following functions:
b OF (ON/OFF): indicates the position of the switch-disconnector poles
b CAM (early-make or early-break function): indicates the position of the handle.
Used in particular for:
v CAO early-break switch (auxiliary contacts open before the main contacts), used,
for example, to automatically open a circuit breaker or a contactor before opening
the Interpact INS
v CAF early-make switch (auxiliary contacts close before the main contacts).
b switching of very small loads. A “low-level” version of the auxiliary contacts exists
for switching very small loads (for example, to control a PLC or electronic circuits).
Standards
The auxiliary contacts comply with international standard IEC 60947-5.1.
Installation
They simply snap in under the auxiliaries cover (supplied as standard) of the
switch-disconnector.
Insulation
Sealable auxiliary shield to protect against direct contact with power circuits.
Electrical characteristics of auxiliary contacts for Interpact INS and INV
Rated thermal current (A)
Minimum load
Standard
6
10 mA at 24 V
AC
E54500
Utilisation category
(IEC 60947-5-1)
Operational current (A) 24 V
48 V
110 V
220/240 V
250 V
380/415 V
440 V
660/690 V
CAO or CAF
OF1
OF2
OF3
E88715
Interpact INS/INV320 to 630
CAO or CAF
Low level
5
1 mA at 4 V
DC
AC
DC
AC12 AC15 DC12 DC14 AC12 AC15 DC12 DC14
6
6
6
6
6
6
5
4
6
6
6
3
3
0.1
2.5
2.5
0.8
1
0.2
0.05
0.3
0.03
5
5
5
5
3
3
2.5
2
5
5
1.5
1.5
5
2.5
0.8
1
0.2
0.05
0.3
0.03
Interpact INS40 to 2500, INV100 to 2500
Possible combinations
Interpact
OF block
CAM block (CAO or CAF)
INS40 to 160
INS250
INS400/630
INS630b/1600
INS2000/2500
2
2
3
3
3
2
2
1
1
1
or
or
and
and
and
OF1
OF2
OF3
E88929
Interpact INS/INV800 to 1600
CAO or CAF
OF1
OF2
OF3
Interpact INS/INV2000 to 2500
Schneider Electric
55
Functions and
characteristics
Current measurements
057355_A
Ammeter module
For Interpact INS250 to 630 and INV100 to 630.
Function
Measures and displays the current of each phase (phase selection by a threeposition switch on the front) on a dial-type ammeter.
Installation
b connects directly to the downstream terminals of the switch-disconnector
(except on a INS250 with a direct handle)
b the ammeter clips into the module housing in any of four 90° positions, i.e. the
switch-disconnector may be installed horizontally or vertically
b degree of protection: IP40 IK 07
b class II insulation between front and power circuits.
Electrical characteristics
Accuracy class 4.5.
Current-transformer module
Interpact INV250 with ammeter module
56
For Interpact INS250 to 630 and INV100 to 630.
Function
Measure phase currents for display by an ammeter or a Digipact IM or PM module
(not supplied, see the corresponding catalogue).
Installation
b connects directly to the downstream terminals of the switch-disconnector
b degree of protection: IP40.3
b class II insulation between front and power circuits
b connection via six built-in terminals for cables with a cross-sectional area
of 2.5 mm2.
Electrical characteristics
b current transformer with 5 A secondary winding
b accuracy class 3 for the following values of consumed output power:
v 100 A rating - 1.6 VA
v 150 A rating - 3 VA
v 250 A rating - 5 VA
v 400/630 A rating - 8 VA.
Schneider Electric
Functions and
characteristics
Rotary handle
052171_A
INS40-160
INS250
INS320-630
INS630b-1600 INS2000-2500
INV100-250
INV320-630
INV630b-1600 INV2000-2500
Standard rotary handle
Front direct
Standard
Standard
Standard
Standard
Standard
Lateral direct
Standard
With conversion
No
No
No
Front extended
Optional
Optional
Optional
Optional
Optional
Lateral extended
Optional (2)
Optional
No
No
No
Red and yellow rotary handle for emergency-off switch-disconnectors
056656_A
Interpact INS160 with lateral direct rotary handle
Front direct
Standard
Standard
Standard
Standard
No (3)
Lateral direct
Standard
With conversion
No
No
No
Front extended
Optional
Optional
Lateral extended
Optional (1) (2) Optional (1)
Optional
Optional
No (3)
No
No
No
or
E54502
Direct rotary handle
on INS40 to 160
or
ø5...8
E54503
Direct rotary handle on
INS250 and INV100 to 250
Direct rotary handle
on INS/INV320 to 630
E88716
059495_A
N
056652_A
.1
Interpact INS630 with front extended rotary handle
.2
Interpact INS250 with lateral extended rotary handle
Direct rotary handle
b degree of protection IP40.5
b the switch-disconnector may be locked in the OFF
position by one to three padlocks, hasp diameter 5 to
8 mm (not supplied).
Models
b standard with black handle
b emergency-off version with red handle and yellow
front for machine-tool control.
Extended rotary handle
Makes it possible to operate the switch-disconnector,
installed inside a switchboard, from the front or side of
the switchboard. The extended rotary handle may be
installed on the front or the side of the switchdisconnector. Degree of protection IP55.7.
Operation
b suitability for isolation is maintained
b door opening is prevented when the switchdisconnector is in ON position (for front handle only)
b the switch-disconnector may be locked in the OFF
position by one to three padlocks, hasp diameter 5 to
8 mm (not supplied). Locking prevents opening of the
switchboard door (for front handle only).
Models
b standard: with black handle
b emergency-off: with red handle and yellow front for
machine-tool control.
Installation
The extended rotary handle is made up of:
b an assembly that replaces the direct rotary handle
on the Interpact switch-disconnector (secured by
screws)
b an assembly (handle and front plate) to be mounted
on the door or the side of the switchboard. This
assembly is always secured in the same position,
whether the switch-disconnector is installed vertically
or horizontally
b an adjustable extension shaft (see pages
308E4040).
.4
Interpact INS and INV
E54501
(1) The basic switch-disconnector must be the emergency-off (red and yellow) version
(2) Two models for universal enclosures and for Prisma G enclosures
(3) Emergency-off versions not available for INS/INV2000-2500.
Direct rotary handle
on INS/INV800 to 1600
Interpact INS250 emergency-off version with front direct
rotary handle
Schneider Electric
57
E88932
Functions and
characteristics
Coupling accessories
Coupling accessory
This accessory simplifies connection of bars or cables with lugs when coupling two
Compact NS100 to 630 circuit breakers or two Interpact INS/INV100 to 630 switchdisconnectors of the same size.
Pitch between outgoing terminals:
b Interpact INS250 and INV100 to 250: 35 mm
b Interpact INS/INV320 to 630: 52.5 mm
b Compact NS100 to 250: 35 mm
b Compact NS400 to 630: 52.5 mm.
Connection and insulation accessories
The coupling accessory may be fitted with the same connection and insulation
accessories as the coupled circuit breakers or switch-disconnectors.
Possible combinations
Downstream coupling
possible
pitch of outgoing
terminals (mm)
b
b
b
b
b
b
35
35
35
52.5
52.5
52.5
b
b
35
52.5
b
b
35
52.5
Manual source-changeover
INS250 (100 to 250 A) with rotary handle
NS100/250 with rotary handle
NS100/250 on mounting plate with toggle
INS400/630 (320 to 630 A) with rotary handle
NS400/630 with rotary handle
NS400/630 on mounting plate with rotary handle
Complete source-changeover assembly
INS250 (100 to 250 A) complete assembly
INS400/630 (320 to 630 A) complete assembly
Remote-operated source changeover
NS100/250
NS400/630
58
Schneider Electric
Disabling device closing
Functions and
characteristics
056649_A
Padlocking
E89551
b INS40 to 2500 A
b INV100 to 2500 A
b complete source-changeover assembly from 100 to 630 A.
Switch-disconnectors may be locked in the OFF position:
The handle is designed for locking by up to three padlocks (not supplied).
Locking in the OFF position guarantees isolation as defined by the IEC 60947-3
standard. The handle may also be lead-sealed in the OFF position.
.2
.1
E32426
.4
N
Padlocked Interpact INS250 switch-disconnector
Ø5
5
88
Keylocking
E54544
E89552
b INS250-100 to 2500 A
b INV100 to 2500 A
b complete source-changeover assembly from 100 to 630 A.
INS250 to 630, INV100 to 630 or INV1000 to 2500 switch-disconnectors may be
locked in the OFF position using a keylock (optional) that may be installed in the
hole prepared for that purpose on the front of the devices.
The key may not be removed when the switch-disconnector is in the ON position.
Keylocks can also be fitted on switch-disconnectors equipped with extended rotary
handles.
ø5...8
INS/INV switch disconnectors
Locking by padlocks
Locking by keylock
Door locking (2)
Door lock defeat (2)
Door locking,
device padlocked (2)
Lead-sealable handle
INS40 to 80
INS100 to 160
ON
v
–
b
b (1)
–
INS250-100 to 250
INV100 to 250
OFF
ON
b
v
b
v
–
b
–
b (1)
b
–
INS320 to 630
INV320 to 630
OFF
ON
b
v
b
v
–
b
–
b (1)
b
–
INS630b to 1600
INV630b to 1600
OFF
ON
b
v
b
v
–
b
–
b (1)
b
–
INS2000 to 2500
INV2000 to 2500
OFF
ON
b
v
b
v
–
b
–
b (1)
b
–
OFF
b
–
–
–
b
ON
v
–
b
b (1)
–
OFF
b
–
–
–
b
b
v
b
v
b
b
b
b
v
v
v
v
Complete source changeover assembly
INS250-100 to 250
Normal ON
OFF
v
b
v
b
b
–
b (1)
–
–
b
Locking by padlocks
Locking by keylock
Door locking (2)
Door lock defeat (2)
Door locking,
device padlocked (2)
Lead-sealable handle
v
b
v by simple modification of the standard rotary handle.
b (1) using a special tool.
(2) with extended rotary control.
Schneider Electric
Replacement ON
v
v
b
b (1)
–
INS320 to 630
Normal ON
v
v
b
b (1)
–
OFF
b
b
–
–
b
Replacement ON
v
v
b
b (1)
–
v
v
b
v
59
Functions and
characteristics
Switching to a replacement source
A source-changeover system is made up of
two switch-disconnectors or circuit breakers
that are mechanically interlocked.
The mechanism prevents the simultaneous
connection (even transient) of both sources.
Switching from one source to the other can
be achieved by:
b a keylock-type interlocking system
b a mechanical interlocking system
b a complete source-changeover assembly.
Possible positions
Normal
Replacement
Source
changeover
1
0
INS40...160
By keylock
Mechanical
b
Complete assembly
0
1
0
0
INS250
INV100...250
INS320...630
INV320...630
INS630b…2500
b
b
b
b
b
b
b
Interlocking of two devices using keylocks and a captive key
Interlocking is based on two identical keylocks with a single key and a keylock
adapter (different for each device). This solution enables interlocking between two
devices that are physically distant or that have very different characteristics.
Interlocking of two devices with rotary handles
E55460
The direct or extended rotary handles are padlocked with the devices in the OFF
position. The mechanism prevents simultaneous closing of the devices, but allows
them to be opened.
ø5...8
Possible combinations of “Normal” and “Replacement” source switch-disconnectors
ø5...8
rating
“Normal” N
“Replacement” R
INS40
INS63
INS80
INS100
INS125
INS160
INS40
INS63
INS80
INS100
INS125
INS160
Interpact INS (1)
E88930
40
63
80
100
125
160
ON
Interpact INS/INV (2)
I
ø5...8
ON
I
ø5...8
ø5...8
ø5...8
O OFF
O OFF
100
160
200
250
320
400
500
630
INS250-100/INV100
INS250-160/INV160
INS250-200/INV200
INS250-250/INV250
INS320/INV320
INS400/INV400
INS500/INV500
INS630/INV630
(1) With extended rotary handles
only.
(2) Possible with INV, but visiblebreak function is significantly
impaired.
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b b
b b b
b b b b
b b b
b b
b
b
b b
b b b
b b b b
b b b
b b
b
INS250-100/INV100
INS250-160/INV160
INS250-200/INV200
INS250-250/INV250
INS320/INV320
INS400/INV400
INS500/INV500
INS630/INV630
Complete source-changeover assembly for two switchdisconnectors
E89553
These assemblies provide an easy way to implement source changeover functions with:
b a single 3-position rotary handle that controls the two switch-disconnectors
(Normal source ON, OFF, Replacement source ON)
b a smaller size, taking up less room in the switchboard.
A complete source changeover assembly can be ordered with a single catalogue
number.
Possible combinations of “Normal” and “Replacement” source switch-disconnectors
ratings
100
160
200
250
320
400
500
630
“Normal” N
INS250 -100
INS250 -160
INS200 -200
INS250 -250
INS320
INS400
INS500
INS630
b
b
b
b
b
“Replacement” R
INS250 -100
INS250 -160
INS250 -200
INS250 -250
INS320
INS400
INS500
INS630
b
b
b
60
Schneider Electric
Accessories
Functions and
characteristics
Front-panel escutcheons
E55276
E55275
Escutcheons for switch-disconnectors and ammeter modules
Mounted on switchboard panel from the front using four screws.
ø5...8
160
A
120
80
40
0
160/5A
Escutcheon for ammeter
modules
Escutcheon for switchdisconnectors
Identification labels
E18595
Interpact INS40 to 160 switch-disconnectors may receive Telemecanique
prefabricated labels, catalogue number AB1- (eight characters). Interpact INS250
to 630 and INV100 to 630 switch-disconnectors are supplied as standard with a
clip-on label for handwritten indications.
These devices also come with a nameplate into which a label can be inserted.
052760_A
P
D E P. P O M
.P
DE P
O
push
to
trip
Individual enclosures
Interpact INS and INV switch-disconnectors equipped with a front handle may be
installed in individual enclosures.
All fixed, front connections are possible, except right-angle and edgewise terminal
extensions. Spreaders may be installed in the enclosures intended for Interpact
INS250 to 630 and INV100 to 630 switch-disconnectors.
Heavy-duty metal individual enclosure for Interpact INS (IP557)
b metal enclosure
b door with keylock and cut-out for switch-disconnector rotary handle
b extended rotary front handle
b device mounting plate
b removable plate (without holes) for cable entry through bottom.
Heavy-duty insulating individual enclosure for Interpact INS and INV (IP557)
b metal enclosure
b transparent cover, screwed, lead sealable, with cut-out for switch-disconnector
rotary handle
b extended rotary front handle
b device mounting plate
b removable plates (without holes) for cable entry through bottom and/or top.
Dimensions
Metal enclosures
Interpact INS40 to 160
Interpact INS250
Interpact INV100 to 250
Interpact INS320 to 630
Interpact INV320 to 630
Insulating enclosures
Interpact INS40 to 160
Interpact INS250
Interpact INV100 to 250
Interpact INS320 to 630
Interpact INV320 to 630
Schneider Electric
WxHxD
350 x 350 x 250
350 x 450 x 250
350 x 650 x 250
WxHxD
270 x 180 x 185
270 x 360 x 235
360 x 720 x 235
61
62
Schneider Electric
Installation recommendations
Presentation
Functions and characteristics
2
17
Operating principle
Possible installation positions and mounting
techniques
Implementation
Interpact INS40 to 80
Interpact INS100 to 160
Interpact INS250-100 to 250, Interpact INV100 to 250
Complete source-changeover assembly
INS250-100 to 250
Interpact INS320 to 630, Interpact INV320 to 630
Complete source-changeover assembly
INS320 to 630
Connection
64
74
78
INS630b to 1600 and INV630b to 1600
INS2000 to 2500 and INV2000 to 2500
78
82
Use at high temperatures
84
Dimensions and connection
Additional characteristics
Catalogue numbers
Schneider Electric
66
67
68
69
70
85
103
113
63
Installation
recommendations
Operating principle
INS250-100 to 250
INV100 to 250
E94150
OFF
ON
OFF
CAOF
OFF
OFF
ON
OFF
ON
OFF
INS320 to 630
INV320 to 630
ON
OFF
E94151
OFF
OFF
CAM
OF
64
OFF
OFF
ON
ON
OFF
OFF
ON
OFF
Schneider Electric
Installation
recommendations
Operating principle (cont.)
E90497
INS630b to 2500
INV630b to 2500
CAM
OF
OFF
ON
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
ON
OFF
ON
Schneider Electric
OFF
ON
65
Possible installation positions
and mounting techniques
Installation
recommendations
E55418
E55417
E55416
Possible installation positions
ø5...8
ø5...8
ø5...8
E55420
E55419
ø5...8
ø5...8
Possible mounting
INS40 to 160
E55597
.1
.4
.2
E55596
.2
.1
.4
.2
.1
E55421
.4
N
N
N
Ø5
5
Ø5
5
88
Ø5
5
Symmetrical rail
88
88
Plain mounting plate
Slotted mounting plate
E55422
E55416
E55423
INS250-100 to 630 - INV100 to 630
ø5...8
Rails
ø5...8
ø5...8
Plain mounting plate
Slotted mounting plate
E88862
E88863
INS/INV800 to 2500
Rails
66
Plain mounting plate
Schneider Electric
Installation
recommendations
Implementation
Reverse supply
E55424
Interpact switch-disconnectors may be supplied indifferently via the top or bottom
terminals, without any reduction in performance.
ø5...8
Neutral pole position
On Merlin Gerin switch-disconnectors, the neutral pole is traditionally located on
the left-hand side. On the INS and INV ranges, the four poles are identical and the
neutral pole can therefore be located on the right-hand side simply by adding an
appropriate label.
Conductor materials and electrodynamic forces
E55425
to the busbars
Interpact switch-disconnectors may be connected using either bare copper, tinned
copper or tinned aluminium conductors (flexible or rigid bars, cables).
In the event of a short-circuit, thermal and electrodynamic forces are exerted on the
conductors. The conductors must therefore be adequately sized and suitably
supported.
Note that the terminals of electrical devices (switch-disconnectors, contactors,
circuit breakers, etc.) should not be considered to contribute to the support of the
conductors.
Cables ties and flexible bars
outgoing cables
The table below indicates the maximum distances between cable ties depending
on the prospective short-circuit current.
Care must be taken not to exceed a distance of 400 mm between ties mechanically
secured to the switchboard frame.
Type of tie
Max. distance
between ties (mm)
Short-circuit
current (kA rms)
"Panduit" type
Width: 4,5 mm
Max. load: 22 kg
Colour: white
"Sarel" type
Width: 9 mm
Max. load: 90 kg
Colour: black
200
100
50
350
200
100
70
10
15
20
20
27
35
45
50 (double
ties)
100
Note: for cables u 50 mm2, 9 mm wide ties must be used.
Schneider Electric
67
Interpact INS40 to 80
E39432
Installation
recommendations
Front connection of bare copper and
aluminium cables
.4
.2
.1
N
E38888
b Interpact INS40 to INS80 switch-disconnectors are equipped as standard with
connectors for bare copper and aluminium cables
b distribution connectors may be screwed directly to the switch-disconnector
terminals and can be used to connect three cables.
Pole pitch
Distribution connector
If 500 V y U y 690 V,
interphase-barrier or
long terminal shields
are mandatory
18 mm
E89682
e
Bars
Cables
L
Torque
S
e (mm)
L (mm)
L (mm)
S (mm2)
Cu / Al
5 Nm
Standard
device
With distribution
connector
y5
13
y 10
1.5 to 50 rigid
1.5 to 35 flexible
2 Nm
13
y 10
1.5 to 16 rigid
1 to 10 flexible (1)
L
(1) Connection of 1.5 to 4 mm2 flexible cables requires crimped or auto-crimping ferrules.
Insulation of live parts
E88935
E89674
b with long terminal shields
b with terminal shrouds.
Terminal shields
68
Terminal shrouds
Schneider Electric
Interpact INS100 to 160
E32424
E30707
Installation
recommendations
Front connection of bare copper and
aluminium cables
.2
.1
E32423
.4
b 1-cable connectors snap directly onto the device terminals
b distribution connectors for 4 flexible cables are screwed directly to the device
terminals. These connectors are supplied with interphase-barrier (mandatory
installation) which may be replaced by long terminal shields
b Distribloc distribution block supplied via tunnel terminals. Provides 12 screwless
spring type and 1 screw type outgoing terminals.
1-cable
Distribution
connector
connector
1-cable
connector
N
E54545
If 500 V y U y 690 V,
interphase-barrier or
long terminal shields
are mandatory
E55598
Distribution
connector
Lugs
L
Torque
15
10 to 95 rigid
10 to 95 flexible
10
15
1.5 to 25 rigid
1.5 to 16 flexible (1)
3
Distribloc
S
Torque
(Nm)
Supply 5 Nm
Distribution 3 Nm
(1) Connection of 1.5 to 4 mm2 flexible cables requires crimped or auto-crimping ferrules.
Distribloc
E54463
Front connection of insulated bars and
cables with crimped lugs
E38889
.1
Interpact INS100 to INS160 switch-disconnectors are equipped as standard with
terminals comprising nuts with M6 screws, for direct connection of insulated bars
and cables with crimped lugs.
Lugs
The small lugs for copper cables may be used for cables with cross-sectional areas
up to 95 mm2. Secure the lugs by hexagonal crimping or punching.
Lugs are supplied with interphase-barrier and are compatible with the terminal
shields.
Pole pitch
N
E89683
Small lugs for copper cables
If 500 V y U y 690 V,
interphase-barrier or
long terminal shields
are mandatory
L (mm)
S (mm2)
Cu / Al
(Nm)
Bar
30 mm
Dimensions
E90303
Bars
e
Lugs
Ø
Torque
d (mm)
e (mm)
L (mm)
L (mm)
ø (mm)
(Nm)
y 10
2…6.4
y 21
15
u 6.2
8
d
L
Insulation of live parts
E89675
E89674
L
Accessories
Interphase-barrier
b distribution blocks, lugs, right-angle/straight/edgewise terminal extensions and
spreaders are supplied with interphase-barrier
b interphase-barrier may be positioned horizontally or vertically
b they may be replaced by long terminal shields.
Interphase-barrier
E88935
Terminal shields
Terminal shrouds
Schneider Electric
69
Interpact INS250-100 to 250
Interpact INV100 to 250
Complete source-changeover
assembly INS250-100 to 250
E54468
Installation
recommendations
Front connection of bare copper and
aluminium cables
b 1-cable connectors snap directly on to the device terminals or are clipped on to
the right-angle or straight terminal extensions or spreaders.
These connectors are supplied with interphase-barrier.
Material: steel I y 160 A and tinned aluminium I y 250 A.
b 6-cable distribution connectors are screwed directly to the device terminals.
These connectors are supplied with interphase-barrier (mandatory installation)
which may be replaced by long terminal shields.
Material: tinned aluminium.
b Polybloc distribution blocks, for 6 or 9 rigid or flexible cables, are connected
directly to the device terminals. Cable connection is made in spring type terminals
and does not require screws.
E54471
E54465
1-cable connector
¯5...8
If 500 V y U y 690 V,
interphase-barrier or
long terminal shields
are mandatory
E54545
Distribution connector
L
1-cable
connector
steel
y 160A
Aluminium
y 250A
L (mm)
S (mm2) Cu / Al
Torque (Nm)
20
1.5…95 (1)
12
20
10…16
15
25…35
20
50…185
26
E54472
Distribution connector, 6 cables Cu or Al
L (mm)
S (mm2) Cu / Al
Torque (Nm)
S
15 ou 30
1.5…6 (1)
4
8...35
6
Polybloc distribution block, 6 or 9 cables
L (mm)
S (mm2) Cu / Al
Polybloc distribution block
12
1.5…10
(1) Connection of 1.5 to 4 mm2 flexible cables requires crimped or auto-crimping ferrules.
E55426
Dimensions
¯5...8
E55450
E55341
1-cable connector
25,5
Z
44
19
57,5
57,5
Z
X
X
Distribution connector, 6 cables
Z
E55427
Y
X
98,5
166
70
66,5
Schneider Electric
Interpact INS250-100 to 250
Interpact INV100 to 250
Complete source-changeover
assembly INS250-100 to 250 (cont.)
E54463
Installation
recommendations
Front connection of insulated bars and
cables with crimped lugs
E54459
Interpact INS250-100 to INS250 and INV100 to 250 switch-disconnectors are
equipped as standard with terminals receiving snap-in nuts and screws (M8 for
INS/INV up to 250, M10 from 320 upwards) for direct connection of insulated bars
or cables with lugs.
Small lugs for copper cables
E30907
Lugs
Small lugs for aluminium
cables
E89683
¯5...8
Lugs are different for copper and aluminium cables. They are supplied with
interphase-barrier and are compatible with the long terminal shields.
b the small lugs for copper cables may be used for cables with the following crosssectional areas:
v 120, 150 or 185 mm2 (INS/INV up to 250)
Secure the lugs by hexagonal crimping or punching.
b the small lugs for aluminium cables may be used for cables with the following
cross-sectional areas:
v 150 or 185 mm2 (INS/INV up to 250)
Secure the lugs by hexagonal crimping.
Bar
35 mm
If 500 V y U y 690 V,
interphase-barrier or
long terminal shields
are mandatory
Pole pitch
Dimensions
Bars
E90303
e
Ø
Lugs
d
L
Torque
d (mm)
e (mm)
L (mm)
Ø (mm)
L (mm)
Ø (mm)
(Nm)
y 10
y6
y 25
u 10
y 25
u 10
15
L
E55434
Dimensions
10,5
57,5
Z
X
Accessories
E54476
E55445
Insulation of live parts
Interphase-barrier
b distribution blocks, lugs, right-angle/straight/edgewise terminal extensions and
spreaders are supplied with interphase-barrier
b interphase-barrier may be positioned horizontally or vertically
b they may be replaced by long terminal shields.
¯5...8
Interphase-barrier
Schneider Electric
Terminal shields
71
Interpact INS250-100 to 250
Interpact INV100 to 250
Complete source-changeover
assembly INS250-100 to 250 (cont.)
Installation
recommendations
Front connection with accessories
Right-angle
extensions
E90490
E54460
Straight terminal
extensions
Material: tinned copper.
Material: tinned copper
Installation on upstream
terminals
E18601
¯5...8
E18600
Connection of two
cables with lugs
If 500 V y U y 690 V,
interphase-barrier or
long terminal shields
are mandatory
Insulation stripping lengths and tightening torques for cables, bare bars and cables
with lugs are identical to those for direct connection to devices.
E55599
E18599
Material: tinned copper.
E90490
Spreader
Separate parts
Connection of two cables
with lugs
One-piece spreader
Pole pitch
45 mm
Dimensions
E50303
Bars
L (mm)
d (mm)
e (mm)
Ø (mm)
L (mm)
Ø (mm)
(Nm)
e
Ø
Cosses
d
Torque
L
y 25
y 10
y6
8.5
y 25
8.5
15 (1)
L
(1) Tightening torque for spreader
Spreaders, straight terminal extensions and right-angle terminal extensions are
supplied with interphase-barrier.
Dimensions
Right-angle terminal extensions
E55436
39,5
Spreader and straight terminal extensions
114
4
45
159
45
45
45
45
19,5
20,5
E55440
57,5
30
98,5
Z
X
X
17,5
Y
Z
Y
One-piece spreader 3P/4P
180,5
45
Z
98
45
Z
98
E55342
45
43,5
125,5
X
Y
24
72
Schneider Electric
Interpact INS250-100 to 250
Interpact INV100 to 250
Complete source-changeover
assembly INS250-100 to 250 (cont.)
Installation
recommendations
E55446
E25967
Rear connection
Bars or cables with crimped lugs
Interpact INS250-100 to INS250 and INV100 to 250 switch-disconnectors may be
equipped with long or short rear connections, or a mix of the two. The connections
may be positioned flat, on edge or at 45° angles, or any combination thereof.
Material of rear connections: tinned copper.
¯5...8
Connection of bars or cables
with lugs
E90303
Bars
L (mm)
d (mm)
e (mm)
Ø (mm)
L (mm)
Ø (mm)
(Nm)
e
E89683
If 500 V y U y 690 V,
short terminal shields
are mandatory
Dimensions
Bar
L
Ø
Lugs
d
Torque
y 25
y 10
y6
>8
y 25
>8
5 (1)
L
E54473
(1) Tightening torque for rear connections.
Two lenghts
E55447
Dimensions
10
∅8,6
∅20
13
18
57,5
E54474
43 short RC
88 long RC
X
Z
6
Four positions
Bare cables (copper or aluminium)
E54545
E55459
E25969
switch-disconnectors, the rear connections may be equipped with 1-cable
connectors secured by clips.
L
S
Schneider Electric
steel
y 160A
Aluminium
y 250A
L (mm)
S (mm2) Cu / Al
torque (Nm)
20
1.5…95 (1)
12
20
10…16
15
25…35
20
50…185
26
Distribution connector, 6 cables Cu or Al
¯5...8
If 500 V y U y 690 V,
short terminal shields
are mandatory
1-cable
connector
L (mm)
S (mm2) Cu / Al
torque (Nm)
15 or 30
1.5…6 (1)
4
8...35
6
(1) Connection of 1.5 to 4 mm2 flexible cables requires crimped or auto-crimping ferrules.
Insulation stripping lengths and tightening torques for cables, bare bars and cables
with lugs are identical to those for direct connection to devices.
73
Interpact INS320 to 630
Interpact INV320 to 630
Complete source-changeover
assembly INS320 to 630
E55428
E54469
Installation
recommendations
Front connection of bare copper and
aluminium cables
1-cable connector
Torque
E54545
E54470
1-cable and 2-cable connectors, made of tinned aluminium for copper and
aluminium cables, are screwed to the device terminals or to right-angle terminal
extensions. These connectors are supplied with interphase-barrier.
(Nm)
1-cable
connector
2-cable
connector
31
31
L
2-cable connector
S
If 500 V y U y 690 V,
interphase-barrier or
long terminal shields
are mandatory
Dimensions
1-cable connector
49
44
Z
E55431
E55429
Z
14
88,5
88,5
X
X
2-cable connector
46,5
E55430
Z
88,5
X
Insulation of live parts
E54476
Accessories
E88874
Interphase-barrier
b distribution blocks, lugs, right-angle/straight/edgewise terminal extensions and
spreaders are supplied with interphase-barrier
b interphase-barrier may be positioned horizontally or vertically
b they may be replaced by long terminal shields.
Interphase-barrier
74
Terminal shields
Schneider Electric
Interpact INS320 to 630
Interpact INV320 to 630
Complete source-changeover
assembly INS320 to 630 (cont.)
E54463
Installation
recommendations
Front connection of bars and cables with
crimped lugs
E88872
Interpact INS320 à 630 et INV320 à 630 switch-disconnectors are equipped as
standard with terminals receiving snap-in nuts and screws (INS/INV from 320 :
M10) for direct connection of bars or cables with lugs.
Small lugs for copper cables
E30907
Lugs
If 500 V y U y 690 V,
interphase-barrier or
long terminal shields
are mandatory
Lugs are different for copper and aluminium cables. They are supplied with
interphase-barrier and are compatible with the long terminal shields.
b the small lugs for copper cables may be used for cables with the following crosssectional areas:
v 240 or 300 mm2 (INS/INV up to 630).
Secure the lugs by hexagonal crimping or punching.
b the small lugs for aluminium cables may be used for cables with the following
cross-sectional areas:
v 240 or 300 mm2 (INS/INV up to 630).
Secure the lugs by hexagonal crimping.
Pole pitch
E89683
Small lugs for aluminium
cables
45 mm
Dimensions
Bars
E90303
Bar
e
L
Ø
Lugs
d
Torque
d (mm)
e (mm)
L (mm)
Ø (mm)
L (mm)
Ø (mm)
(Nm)
y 15
3 y e y 10
y 32
u 10
y 32
u 10
50
L
Dimensions
INS320 to 630 - INV320 to 630
E55433
Z
14
88,5
X
Schneider Electric
75
Interpact INS320 to 630
Interpact INV320 to 630
Complete source-changeover
assembly INS320 to 630 (cont.)
Installation
recommendations
Spreader
Straight terminal
extensions
Right-angle
terminal extensions
Material: tinned copper.
Material: tinned copper.
Material: tinned copper.
Installation on upstream
terminals
E88876
E88875
E88873
Bar
If 500 V y U y 690 V,
interphase-barrier or
long terminal shields
are mandatory
E88877
E89683
Front connection with accessories
Pole pitch
Without spreader
With spreader
45 mm
52.5 or 70 mm
Dimensions
E90303
Bars
L (mm)
d (mm)
e (mm)
Ø (mm)
L (mm)
Ø (mm)
(Nm)
e
Ø
Lugs
d
Torque
L
with
spreader
with edgewise
terminal ext.
y 40
y 20
3 y e y 10
12.5
y 40
12.5
50 (1)
y 32
y 15
3 y e y 10
> 10.5
y 32
10.5
50 (1)
L
(1) Tightening torque for spreader
Spreaders, straight terminal extensions and right-angle terminal extensions are
supplied with interphase-barrier.
Dimensions
Edgewise terminal extensions
58
vue F
E55438
E55444
F
Right-angle terminal extensions
Z
42
8
61
Z
34
8
88,5
88,5
X
X
Spreader
E55442
K10
K8
K9
K8
K8
K8
K8
26
39
108
X
22,5
Y
Y
Type
Spreader
76
width in mod. of 52.5 mm
width in mod. of 70 mm
Z
K8
K9
K10
52.5
70
187.5
240
135
170
Schneider Electric
Interpact INS320 to 630
Interpact INV320 to 630
Complete source-changeover
assembly INS320 to 630 (cont.)
E25967
Installation
recommendations
E88870
Rear connection of bars or cables with
crimped lugs
Interpact INS320 to 630 and INV320 to 630 switch-disconnectors may be equipped
with long or short rear connections, or a mix of the two. The connections may be
positioned flat, on edge or at 45° angles, or any combination thereof.
Material of rear connections: tinned copper.
Connection of bars or cables
with lugs
Bars
E90303
E88879
If 500 V y U y 690 V,
short terminal shields
are mandatory
Dimensions
L (mm)
d (mm)
e (mm)
Ø (mm)
L (mm)
Ø (mm)
(Nm)
e
Ø
Lugs
Two lenghts
d
L
Torque
y 32
y 15
3 y e y 10
> 10.5
y 32
> 10.5
20 (1)
L
E88880
(1) Tightening torque for rear connections.
Dimensions
Four positions
E89683
E55449
E55447
INS320 to 630 - INV320 to 630
10
∅8,6
∅20
15
∅23,2
13
18
14
30
Bar
57,5
43 short RC
88 long RC
50 short RC
115 long RC
X
Z
E25969
6
E88871
∅13
88,5
Z
X
8
Bare cables (copper or aluminium)
Interpact INS320 to 630 and INV320 to 630, switch-disconnectors,
the rear connections may be equipped with 1-cable connectors secured by clips.
Insulation stripping lengths and tightening torques for cables are identical to those
for direct connection to devices.
If 500 V y U y 690 V,
short terminal shields
are mandatory
Schneider Electric
77
Connection
INS630b to 1600 and
INV630b to 1600
Installation
recommendations
Front connection of insulated bars
Connection of bars
E88889
E88888
E88865
Interpact switch-disconnectors are equipped with terminals for direct connection
of bars.
2 Ø12 maxi
12,5
3 Ø12 maxi
12,5
25
12,5
25 25
80
50
15
Insulation of live parts
Accessories
E88866
E88682
Interphase-barrier
b interphase-barrier may be positioned horizontally or vertically
b they may be replaced by long terminal shields.
Interphase-barrier
Terminal shield
Compatibility of terminal shields + base for connections
Base
Terminal
Spreader
Interphase-barrier
shields
Base
Terminal shields
Spreader
Interphase-barrier
78
–
YES
NO
NO
YES
–
NO
NO
YES
NO
–
YES
NO
NO
YES
–
Schneider Electric
Installation
recommendations
Connection (cont.)
INS630b to 1600 and
INV630b to 1600 (cont.)
Connections
E88868
E88666
There are many solutions to connect bars:
b vertical connection adapters to connect edgewise bars
b spreaders with a 95 mm pole pitch to increase the clearance between bars.
E88663
Vertical connection adapters
E89547
E88867
Spreaders
Connection of cables with lugs
Cable-lug adapters are used in conjunction with vertical connection adapters.
Thwey may be used to connect one to four cables (y 300 mm2) with crimped lugs.
To ensure adequate mechanical strength, the cable-lug adapters must be secured
together by spacers.
E88668
E88869
Lugs for copper cables
Cable lug adapters
Schneider Electric
79
Connection (cont.)
INS630b to 1600 and
INV630b to 1600 (cont.)
Installation
recommendations
Dimensions
Connection with spreaders
97,5
110
95
95
70
70
70
95
70
70
12,5
12,5
202
187
E88671
202
187
E88670
E88669
95
95
X
X
X
187
202
187
202
Y
56,5
Y
15
Spreader details
13,5
=
25
30
82 52
15
=
38,5
13,5
=
25
30
82 52
15
5 Ø11
E88672
=
38,5
E89550
E89548
25
77
77
77
38,5
=
38,5
13,5
=
25
=
30
30
82 52
82 52
15
15
5 Ø11
5 Ø11
25
52
25
25
25
52
52
52
For 3P switch-disconnectors
13,5
=
For 4P switch-disconnectors
Connection with vertical connection adapters
135
70
135
70
70
70
70
15
E88675
221
206
171
E88674
E88673
15
X
X
X
171
206
221
Y
50,5
12
Y
Connector details
E88676
25
Note:
2 connection possibilities on vertical connection adapters
(21 mm between centres)
Recommended connection screws: M10 class 8.8.
Tightening torque: 50 Nm with contact washer.
80
89
= =
12,5
15
13
101
15
21
17
Schneider Electric
E89549
77
Connection (cont.)
INS630b to 1600 and
INV630b to 1600 (cont.)
Installation
recommendations
Connection using vertical connection adapters and cable-lug adapters
135
70
70
135
70
70
70
15
15
10
E88679
256
206
191
E88678
E88677
10
X
X
X
191
206
256
Y
155
Y
12
Cable lug adapter detail
184
50
50
50
17
E88680
15
50
80
5 Ø13
Schneider Electric
5 Ø11
81
Connection (cont.)
INS2000 to 2500 and
INV2000 to 2500
Installation
recommendations
Front connection of insulated bars
Connection of bars
E88889
E88888
E94444
Interpact switch-disconnectors are equipped with terminals for direct connection
of bars.
2 Ø12 maxi
12,5
3 Ø12 maxi
12,5
25
12,5
50
15
25 25
80
Insulation of live parts
Accessories
E94445
Interphase-barrier
82
Schneider Electric
Connection (cont.)
INS2000 to 2500 and
INV2000 to 2500 (cont.)
Installation
recommendations
Dimensions
Connection with spreaders
462,5
347,5
67,5
115
115
67,5
115
115
205
X
X
E94153
90
E94152
E94154
90
115
205
270
X
440
180
205
76
440
205
Y
24
270
180
Y
For switch-disconnectors 3P
Schneider Electric
E94158
E94157
E94156
E94155
Spreader details
For switch-disconnectors 4P
83
Use at high temperatures
Installation
recommendations
Power dissipated and resistance per pole
Interpact INS
Rating (A)
Resistance per pole (mΩ)
Power dissipated per pole (W)
Interpact INS/INV
Rating (A)
Resistance per pole (mΩ)
Power dissipated per pole (W)
40
63
80
100
125
160
40
0.3
0.5
63
0.3
1.2
80
0.3
1.9
100
0.2
2
125
0.2
3.1
160
0.2
5.1
100
160
200
250
320
400
500
630
100
0.15
1.5
160
0.15
4
200
0.15
6
250
0.15
9.5
320
0.06
6.1
400
0.06
9.6
500
0.06
15
630
0.06
24
Interpact INS/INV
800
1000
1250
1600
2000
2500
Rating (A)
Resistance per pole (mΩ)
Power dissipated per pole (W)
800
0.024
16
1000
0.024
24
1250
0.024
38
1600
0.024
62
2000
0.012
48
2500
0.012
75
40
63
80
100
125
160
63
63
63
80
80
80
100
100
100
125
125
125
160
160
150
100
160
200
250
320
400
500
630
100
100
100
160
160
160
200
200
200
250
250
250
320
320
320
400
400
400
500
500
500
630
590
550
Front connection with right-angle terminal extension + bare-cable connectors
Thermal current Ith at
55 °C
100
160
200
60 °C
100
160
200
65 °C
100
160
200
70 °C
100
160
200
250
250
250
240
320
320
320
320
400
400
400
400
500
500
500
500
630
590
550
510
Front connection / rear connection with ammeter or CT module
Thermal current Ith at
40 °C
100
160
50 °C
100
160
55 °C
100
160
60 °C
100
160
65 °C
100
160
70 °C
100
160
250
250
250
240
230
210
320
320
320
320
320
320
400
400
400
400
400
400
500
500
500
500
480
450
600
575
540
505
480
450
Temperature derating
Interpact INS
Front connection with bare-cable connectors or lugs
Thermal current Ith at
60 °C
40
65 °C
40
70 °C
40
Interpact INS/INV
Front connection / rear connection
Thermal current Ith at
60 °C
65 °C
70 °C
Interpact INS/INV
630b
Direct connection by flat-facing bars
Thermal current Ith at
40 °C
630
45 °C
630
50 °C
630
55 °C
630
60 °C
630
65 °C
630
70 °C
630
Interpact INS/INV
630b
800
1000
200
200
200
200
200
200
1600 (4 bars 50 x 5)
2000
2500
with or without with or without with
term. shield term. shield term. shield
1250
without
term. shield
with
term. shield
without
term. shield
without
term. shield
without
term. shield
800
800
800
800
800
800
800
1000
1000
1000
1000
1000
1000
1000
1250
1250
1250
1250
1250
1250
1060
1250
1250
1250
1250
1250
1250
1210
1600
1570
1500
1420
1340
1250
1060
1600
1600
1550
1470
1390
1300
1210
2000
2000
2000
2000
2000
2000
2000
2500
2500
2500
2500
2500
2500
2400
800
1000
1250
Connection by flat-facing bars via spreaders, WITHOUT terminal shields
Thermal current Ith at
40 °C
630
800
1000
1250
45 °C
630
800
1000
1250
50 °C
630
800
1000
1250
55 °C
630
800
1000
1250
60 °C
630
800
1000
1250
65 °C
630
800
1000
1250
70 °C
630
800
1000
1240
Interpact INS/INV
630b
800
1000
1250
1600 (3 bars 80 x 5)
1600
1600
1580
1500
1420
1330
1240
1600
with
without
term. shield term. shield
Connection of edgewise bars via vertical connection adapters or cables via vertical connection adapters with cable-lug adapters
Thermal current Ith at
40 °C
630
800
1000
1250
1600
1600
45 °C
630
800
1000
1250
1600
1600
50 °C
630
800
1000
1250
1600
1600
55 °C
630
800
1000
1250
1600
1600
60 °C
630
800
1000
1250
1600
1600
65 °C
630
800
1000
1250
1520
1560
70 °C
630
800
1000
1250
1410
1450
Thermal current Ith in Amps (QA)
84
Schneider Electric
Dimensions and connection
Presentation
Functions and characteristics
Installation recommendations
2
17
63
Interpact INS40 to 160
Interpact INS250-100 to 630
Interpact INV100 to 630
Interpact INS630b to 1600
Interpact INV630b to 1600
Interpact INS2000 to 2500
Interpact INV2000 to 2500
Mechanical interlocks for direct
and extended handles (INS40 to 630, INV100 to 630)
Complete source-changeover assembly
86
90
90
94
94
96
96
98
INS250-100 to 250 A and INS320 to 630
99
Installation of downstream coupling
99
100
(INS250-100 to 630, INV100 to 630)
Front panel accessories (INS250-100 to 2500, INV100 to 630)
Additional characteristics
Calalogue numbers
Schneider Electric
101
103
113
85
Interpact INS40 to 160
Dimensions
and connection
Dimensions
Front handle
E32252
E32250
Y
(a)
(b)
Y
E32255
K
H3
P5
X
H1
H7
X
X
H5
H
H2
H4
H6
120°
P
K1
L
P1
P2
P3
P4
K1 K1
K
(a) Terminal shields INS40/63/80
(b) Terminal shields INS100/125/160
L1
L2
Z
Dimensions (mm)
Type
INS40/63/80
INS100/125/160
H
H1
H2
H3
H4
H5
H6
H7
K
K1
L
L1
L2
P
P1
P2
P3
P4
P5
22.5
22.5
45
45
40.5
50
81
100
42.5
50
85
100
73.5
110
147
220
1
7.5
18
30
46
67.5
73
119
90
135
21.3
18.5
43
45
47
47
62.5
62.5
79
79
5
5
Extended front handle
E32609
Dimensions (mm)
E32610
Type
e
INS40/63/80
INS100/125/160
X
Type
INS40/63/80
INS100/125/160
Z
A (on back plate) B (on rail)
mini
maxi
mini
maxi
128
128
519
519
123
123
e
K
Length
of shaft
1…3
1…3
1
7.5
A – 69
A – 69
514
514
47
B
A
Door or front panel cutout for front handle
Direct
Extended
X
Type
C
R
K
INS40/63/80
INS100/125/160
47
47
92
137
1
7.5
E32611
E32261
Dimensions (mm)
=
C
=
Y
=
=
R
86
Schneider Electric
Interpact INS40 to 160 (cont.)
Dimensions
and connection
Dimensions
E32256
E32254
E32253
Standard lateral handle
X
X
120°
60°
P6
P7
Dimensions (mm)
Z
Y
L3
Type
L3
P6
P7
INS40/63/80
INS100/125/160
109
154
40
42.5
66.1
69.3
E38890
Extended lateral handle
65
32,5
E32613
e
I
75
120°
X
X
O
37,5
Y
33
B
P6
Z
Dimensions (mm)
Type
With shaft
INS40/63/80
INS100/125/160
Without shaft
INS40/63/80
INS100/125/160
B
mini
maxi
155
200
396
441
e
P6
Length
of shaft
1…3
1…3
40
42.5
B – 95
B – 140
B
e
P6
102
147
1…3
1…3
40
42.5
Lateral handle for functional enclosure
E38890
65
32,5
E38891
e
I
75
120°
X
X
O
37,5
Y
33
B
P6
Z
Dimensions (mm)
Type
Note:
Lines X and Y indicate the axes of symmetry of the
switch-disconnector.
Reference plane Z corresponds to the back of the switchdisconnector.
Schneider Electric
INS40/63/80
INS100/125/160
Enclosure Type
length
of shaft
B
e
P6
550 mm
600 mm
550 mm
600 mm
149
174
194
219
1…3
1…3
1…3
1…3
41.5
41.5
41.5
41.5
short
long
short
long
87
Interpact INS40 to 160 (cont.)
Dimensions
and connection
Dimensions (cont.)
E38892
Front panel cutout for extended handle
Ø6
Ø50
55°
X
Z
R = 36
23,4
23,4
P6
Installation
sur rail symétrique
On rail
On a backplate
C2
E32452
E32259
ØT
X
C1
Dimensions (mm)
Y
R1
R2
88
Type
INS40/63/80
INS100/125/160
C1
C2
R1
R2
ØT
U
40
37.5
80
75
10
22.5
36
60
4.5
4.5
35
35
Schneider Electric
Schneider Electric
89
Interpact INS250-100 to 630
Interpact INV100 to 630
Dimensions
and connection
Dimensions
E51178
E51177
Front handle
H3
X
H5
E51179
(a)
(b)
H7
X H8
H1
H
H2
H4
H6
K1
P
Z
P1
P2
P3
P4
Y
K1
K
L1
(a) Terminal shields
(b) Interphase-barrier
K1
L
Dimensions (mm)
Type
H
INS250
40
INV100/250
INS320/630 61.5
INV320/630
H1
H2
H3
H4
H5
H6
H7
H8
H11 K
K1
L
L1
P
P1
P2
P3
P4
80
68
136
148
296
166
332
115
57.5
17.5
35
70
140
21.5
86
96
131
138
123
102.5 205
215
430
–
–
177
88.5
22.5
45
92.5
185
26
120
130
160.4 162
Extended front handle
E54513
With escutcheon
Dimensions (mm)
E54514
Type
e
mini maxi
INS250
185 600 1…3
INS320/630 204 600 1…3
E90480
e
A
X
X
Type
K
P5
INS250
17.5 86
INS320/630 22.5 110
P6
88
112
Type
Length of shaft A
INS250
101
INS320/630 124
A
Z
47
P5
P6
Z
Door or front panel cutout for front handle
Standard without escutcheon
Standard with escutcheon
E54508
E51184
E90484
Extended
=
X
X
H9
=
C7
C6
Y
Y
L3
R6
R7
L4
Dimensions (mm)
Type
C6
INS250
51.5
INS320/630 76.5
90
C7
H9
L3
L4
R6
R7
103
153
82
127
65.5
85.5
131
171
81
101
162
202
Schneider Electric
Interpact INS250-100 to 630
Interpact INV100 to 630 (cont.)
Dimensions
and connection
Dimensions
Standard lateral handle for INS250-100 to 250 and INV100 to 250
E56573
E56574
91
X
100
50
Y
203
Extended lateral handle for INS250-100 to 250 and INV100 to 250
E56575
E56576
1...3
X
Y
152,5 mini
577 maxi
48
E56577
Door or front panel cutout for lateral handle
Installation
On panel fixed/FC
On panel fixed/RC
On rail
K1 K1 K1
L6
L5
E90473
E51183
E90472
Ø5
H11
X
X
H10
X
H8
H11
H10
H11
Y
Y
Y
L5
L6
Schneider Electric
Note:
Lines X and Y indicate the axes of symmetry of the
switch-disconnector.
Reference plane Z corresponds to the back of the switchdisconnector.
91
Interpact INS250-100 to 630
Interpact INV100 to 630 (cont.)
Dimensions
and connection
Dimensions
E90475
Switch-disconnector equipped
with current transformer
E94201
E90474
Switch-disconnector with ammeter module
Direct handle (*)
Extended handle
X
X
X
H15 H17 H19
H9 H11 H13
H15 H17 H19
H14 H16 H18
H14 H16 H18
H8 H10 H12
P1
P2
P47
P1
P2
P47
P1
P2
P3 (1)
P4 (2)
Z
Z
Z
(*) Only for INS250/INV100 to 250.
(1) To front of direct handle.
(2) To front of key.
Front panel cutout
E90476
E94202
E90477
Switch-disconnector with ammeter module
Direct handle (*)
Extended handle
X
X
X
C23
C22
C28
C29
(*)
C27
C27
Z
Z
P43
185 y A y 600
Y
R16
R17
R14
R15
(*) Only for INS250/INV100 to 250 with
direct handle and ammeter module.
Note:
lines X and Y indicate the axes of symmetry of the switchdisconnector.
Reference plane Z corresponds to the back of the switchdisconnector.
92
Schneider Electric
Interpact INS250-100 to 630
Interpact INV100 to 630 (cont.)
Dimensions
and connection
Connection (for direct rotary handle equipped with ammeter module)
On a backplate
Fixed front connection
On rails
Fixed rear connection
K2
K1
K
K1
K1
ØT
ØT4
K2
X
E21521
E90479
E90478
K
X
G1
X
G
G7
G6
U(e)
G9
G1
G
G8
G7
G6
ØT
Y
Y
Y
Connection (for extended rotary handle equipped with ammeter module)
On a backplate
Fixed front connection
On rails
Fixed rear connection
K2
K
K1
K1
K1
ØT4
E94258
K2
E94257
E94256
ØT
X
K
U(e)
X
X
G1
G1
G
G
G11
G13
G11
G10
G10
G12
ØT
Y
Y
Y
Dimensions (mm)
Type
C22
C23
C27
C28
C29
G
G1
G6
G7
G8
G9
G10
G11
G12
G13
INS/INV100 to 250
INS/INV320 to 630
41
63.5
82
127
56.5
56.5
187
162
??
??
62.5
100
125
200
137.5
200
200
300
145
213.5
215
327
??
??
??
??
??
??
??
??
Type
H8
H9
H10
H11
H12
H13
H14
H15
H16
H17
H18
H19
INS/INV100 to 250
INS/INV320 to 630
216
202.5
282
305
231.5
217.5
??
??
??
??
??
??
??
??
??
??
??
??
??
??
??
??
??
??
Type
K
K1
K2
P1
P2
P3
P4
P43
P47
R14
R15
R16
R17
ØT
ØT4
U(e)
INS/INV100 to 250
INS/INV320 to 630
17.5
22.5
35
45
70
90
81
95.5
86
110
131
160.4
138
162
89
112
137
162
48.5
64.5
97
129
46.5
64.5
93
93
6
6
22
32
y 32
y 32
Schneider Electric
93
Interpact INS630b to 1600
Interpact INV630b to 1600
Dimensions
and connection
Dimensions
Direct front handle
3 poles
E88687
(a)
4 poles
(b)
(a)
(b)
260,5
E88688
E88689
247
185
X
270
117,5
270
X
X 270
300
150
247
Y
Y
260,5
70
70
56,5
105
105,5
70
70
20
210
140,5
70
175
20
280
340
410
146,5
(a) Terminal shields
(b) Interphase-barrier
198
Z
E88692
Extended front handle
E88693
Dimensions (mm)
e
Type
A
INS630b/1600
mini
210
maxi
583.5
e
K
Length
1…3
87
of shaft A
?
R100
30°
X
X
H1
H
30°
Y
K
Z
A
Note:
Lines X and Y indicate the axes of symmetry of the
switch-disconnector.
Reference plane Z corresponds to the back of the switchdisconnector.
94
Schneider Electric
Interpact INS630b to 1600
Interpact INV630b to 1600 (cont.)
Dimensions
and connection
E90305
Door or front panel cutout for extended handle
Direct front handle
Extended front handle
B
E88694
E90471
A
X
G
X
F
Y
Z
E
C
D
Cutout for switch-disconnector cover (mm)
Type
3P
4P
A
D
E
F
G
107
107
299
369
103
173
108
108
216
216
Cutout for switch-disconnector front (mm)
Type
3P
4P
B
D
E
F
G
142
142
268
228
85
155
95.5
95.5
191
191
Cutout for escutcheon (mm)
Type
3P
4P
C
D
E
F
G
132
132
327
397
110
180
121.5
121.5
243
243
Installation
E88884
On rail
E88690
On backplate
Ø9
X
X
180
90
90
Y
Y
320 (3P)
390 (4P)
Schneider Electric
115 (3P)
185 (4P)
180
320 (3P)
390 (4P)
115 (3P)
185 (4P)
95
Interpact INS2000 to 2500
Interpact INV2000 to 2500
Dimensions
and connection
Dimensions
Direct front handle
3 poles
4 poles
X
X 410
X
210
440
185
235
Y
390
Y
186,5
17,5
221,5
177,5
227,5
247,5
E94162
E94160
E94161
177,5
51
132,5
51
410
62,5
462,5
347,5
320
96
Schneider Electric
Interpact INS2000 to 2500
Interpact INV2000 to 2500 (cont.)
Dimensions
and connection
E90471
E94163
Door or front panel cutout for extended handle
Direct front handle
X
G
F
Y
E
D
E94451
Extended front handle
Cutout for switch-disconnector cover (mm)
E88694
Type
e
3P
4P
A
D
E
F
G
188
188
299
369
103
173
108
108
216
216
Cutout for switch-disconnector front (mm)
X
Type
3P
4P
B
D
E
F
G
223
223
268
228
85
155
95.5
95.5
191
191
Cutout for escutcheon (mm)
Z
Type
A
3P
4P
64
C
D
E
F
G
213
213
327
397
110
180
121.5
121.5
243
243
Installation
E88690
On backplate
Ø9
X
180
90
Y
320 (3P)
390 (4P)
Schneider Electric
115 (3P)
185 (4P)
97
Mechanical interlocks for direct
and extended handles
Dimensions
and connection
(INS40 to 630, INV100 to 630)
Dimensions for direct handle (INS250-100 to 630 and INV100 to 630)
E54511
E54510
F
P
X
X
Q
D
C
Y
Y
E
B
G
A
Z
Dimensions (mm)
Door cutout for direct handle
Type
E54512
INS250
INV100/250
INS320/630
INV320/630
A
B
C
325 90
D
E
87.5 175 70
F
H
K
L
M
N
G
156 17.5 295 75.5 150 75
P
Q
106 68
136
416 115 100 200 92.5 210 22.5 386 100 175 74.5 130 102.5 205
N
X
Y
M
Y
H
H
F
L
K
Dimensions for extended handle (INS40 to 630 and INV100 to 630)
E55451
E55452
F
P
X
X
Q
D
C
Y
G
Y
B
E
47
A
Z
Door cutout for extended handle
H
Dimensions (mm)
Type
A
B
C
D
E
F
G
H
mini maxi
P
Q
INS40/80
INS100/160
INS250
INV100/250
INS320/630
INV320/630
325
325
325
90
90
90
87.5
87.5
87.5
175
175
175
46
70
70
156
156
156
155
200
185
396
441
600
0
0
17.5
45
50
68
90
100
136
416
115
100
200
92.5
210
204
600
22.5
102.5 205
E55453
H
X
Y
Y
Note:
lines X and Y indicate the axes of symmetry of the switch-disconnector.
Reference plane Z corresponds to the back of the switch-disconnector.
F
98
Schneider Electric
Complete source changeover
assembly
INS250-100 to 250 A
and INS320 to 630
Dimensions
and connection
E68354
Dimensions of the complete source-changeover assembly with a direct handle
Y
E68355
Y
D
E
X
A
B
C
Dimensions (mm)
Front cutout
Type
E68356
INS250
INS320/630
A
B
60.4
82.5
130.4 296
175
395
C
D
E
68
136
102.5 205
F
G
H
131
155
61.8
87
279.3 42
383.7 64
I
J
K
84
128
156
210
I
X
J
Y
Y
G
K
H
E90486
E90485
Dimensions of the complete source-changeover assembly with an extended handle
Y
Y
F
X
G
X
H
C
A
D
E
B
Z
Dimensions (mm)
E90487
Door cutout
X
Type
A
B
C
D
E
F
G
H
I
J
INS250
INV100/250
INS320/630
INV320/630
136
631
35
70
295.4
50
100
132
60.4
155.7
163
658
45
90
395
75
150
205
82.5
210
Note:
lines X and Y indicate the axes of symmetry of the switch-disconnector.
Reference plane Z corresponds to the back of the switch-disconnector.
Y
Y
I
J
Schneider Electric
99
99
Installation of downstream
coupling
Dimensions
and connection
(INS250-100 to 630, INV100 to 630)
Dimensions
Y
E55454
E55455
Y
X
X
L38
L37
Connection
E55456
Dimensions
Y
Y
Y
L28
Y
L29
E55458
L30
L35
L36
E55457
L31
X
K9
G30
G3
K1 K1 K1
K8
G29 G52
G2
K1 K1 K1
X
K4
K3
G28
K16
K2 K2 K2
L32
L39
L33
L34
L40
Dimensions (mm)
Type
INS250
INV100/250
INS320/630
INV320/630
G2
105.5
G3
169
G28
225.2
G29
83.5
G30
127.5
G52
143.5
K1
35
K2
35
K3
51
K4
156
K8
57.5
K9
157.5
K16
25.4
141
240.7
315
118.4
163.4
202.5
45
52.5
75
210
88.5
225.7
26.1
Type
INS250
INV100/250
INS320/630
INV320/630
L28
320
L29
82.2
L30
300
L31
72.2
L32
16.4
L33
123
L34
139.5
L35
74.5
L36
19.5
L37
70
L38
21.5
L39
24.9
L40
140
420
105.2
400
95.2
11.1
187.5
184.7
96.5
24
92.5
26
22.4
210
100
Schneider Electric
Front-panel accessories
Dimensions
and connection
(INS250-100 to 2500, INV100 to 2500)
Front-panel escutcheon
E56500
E56501
E56502
For switch-disconnectors
M6
A2
M7
D1
D2
Dimensions (mm)
Type
INS250
INV100/250
INS320/630
INV320/630
INS630b/2500
INV630b/2500
3P
4P
A2
D1
D2
M6
M7
174
3.5
6.5
114
101
215.5
3.5
6.5
164
151
346
416
3.5
3.5
11.5
11.5
257.5
257.5
242 x 326.5
242 x 396.5
E21650
E21652
E21651
For ammeter module
93,5
157
80,5
3,5
6,5
E94165
E94164
Front alignment (only for INS/INV250-100)
ø5...8
Schneider Electric
101
102
Schneider Electric
Additional characteristics
Presentation
Functions and characteristics
Installation recommendations
Dimensions and connection
Schneider Electric
2
17
63
85
Protection of switch-disconnectors
104
INS40 to 160 by Compact NS circuit breaker or fuse
INS/INV100 to 630 by Compact NS circuit breaker or fuse
INS/INV630b to 2500 by Compact NS circuit breaker or fuse
INS/INV630b to 2500 by Masterpact circuit breakers NT and NW
104
106
108
110
Catalogue numbers
113
103
Additional characteristics
Protection
of switch-disconnectors
INS40 to 160 by Compact NS circuit
breaker or fuse
E88710
Interpact INS switch-disconnectors
Upstream protection
By circuit breaker
380/415 V
ø5...8
By circuit breaker
440/480 V (*)
By circuit breaker
500 V (INS40 to INS80)
500/525 V (INS100 to INS160)
By circuit breaker
690 V
Per fuse
500 V
(*) Applicable for 480 V
NEMA.
(1) Mandatory protection
by an external thermal
relay.
(2) No external thermal
protection.
104
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type aM (1) / max. rating (A)
Isc max.
making capacity
type gG (2) / max. rating (A)
Isc max.
making capacity
type gG (1) / max. rating (A)
Isc max.
making capacity
type BS (2) / max. rating (A)
Isc max.
making capacity
type BS (1) / max. rating (A)
Isc max.
making capacity
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
Schneider Electric
Additional characteristics
Protection
of switch-disconnectors (cont.)
INS40 to 160 by Compact NS circuit
breaker or fuse (cont.)
INS40
INS63
INS80
INS100
INS125
INS160
NS100N / 40
25
52
NS100H-L / 40
36
75
NS160N / 40
25
52
NS160H-L / 40
25
52
NSC100N / 40
18
37
NG125N / 40
25
52
NG125H / 40
36
75
NG125L / 40
50
105
NSA160N / 40
30
63
NS100N / 40
25
52
NS100H-L / 40
35
73
NS160N / 40
25
52
NS160H-L / 40
25
52
NSC100N / 40
18
37
NS100N / 40
18
36
NS100H-L / 40
18-25
36-53
NS160N / 40
15
30
NS160H-L / 40
15
30
NSC100N / 40
10
17
–
–
–
–
–
–
–
–
–
–
–
–
40
80
176
32
100
220
125
100
220
32
80
176
125 & 100M125
80
176
NS100N / 63
25
52
NS100H-L / 63
36
75
NS160N / 63
25
52
NS160H-L / 63
25
52
NSC100N / 63
18
37
NG125N / 63
25
52
NG125H / 63
36
75
NG125L / 63
50
105
NSA160N / 63
30
63
NS100N / 63
25
52
NS100H-L / 63
35
73
NS160N / 63
25
52
NS160H-L / 63
25
52
NSC100N / 63
18
37
NS100N / 63
18
36
NS100H-L / 63
18-25
36-53
NS160N / 63
15
30
NS160H-L / 63
15
30
NSC100N / 63
10
17
–
–
–
–
–
–
–
–
–
–
–
–
63
80
176
50
100
220
125
100
220
50 & 32M50
80
176
125 & 100M125
80
176
NS100N / 80
25
52
NS100H-L / 80
36
75
NS160N / 80
25
52
NS160H-L / 80
25
52
NSC100N / 80
18
37
NG125N / 80
25
52
NG125H / 80
36
75
NG125L / 80
50
105
NSA160N / 80
30
63
NS100N / 80
25
52
NS100H-L / 80
35
73
NS160N / 80
25
52
NS160H-L / 80
25
52
NSC100N / 80
18
37
NS100N / 80
18
36
NS100H-L / 80
18-25
36-53
NS160N / 80
15
30
NS160H-L / 80
15
30
NSC100N / 80
10
17
–
–
–
–
–
–
–
–
–
–
–
–
80
80
176
63
100
220
125
100
220
63 & 32M63
80
176
125 & 100M125
80
176
NS100N / 100
25
52
NS100H-L / 100
70
154
NS160-250N / 100
36
75
NS160-250H-L / 100
70
154
NSC100N / 100
18
37
NG125N / 100
25
52
NS160-250N / 125
36
75
NS160-250H-L / 125
70
154
NS160-250N / 160
36
75
NS160-250H-L /160
70
154
Schneider Electric
NSA160N / 100
30
63
NS100N / 100
25
52
NS100H-L / 100
65
143
NS160-250N / 100
35
73
NS160-250H-L / 100
65
143
NSC100N / 100
18
37
NS100N / 100
18
36
NS100H-L / 100
35-100
73-220
NS160-250N / 100
22
46
NS160-250H-L / 100
22
46
NSC100N / 100
10
17
NS100N / 100
8
14
NS100H-L / 100
10-75
17-165
NS160-250N / 100
8
14
NS160-250H-L / 100
10-20
17-40
100
80
176
80
100
220
160
100
220
80 & 63M80
80
176
160 & 100M160
80
176
NG125N / 125
25
52
NSA160N / 125
30
63
NS160N / 160
30
63
NS160-250N / 125
35
73
NS160-250H-L / 125
65
143
NS160-250N / 160
35
73
NS160-250H-L /160
65
143
NS160-250N / 125
22
46
NS160-250H-L / 125
22
46
NS160-250N / 160
22
46
NS160-250H-L /160
22
46
NS160-250N / 125
8
14
NS160-250H-L / 125
10-20
17-40
125
55
121
100
100
220
160
100
220
100 & 63M100
80
176
160 & 100M160
80
176
NS160-250N / 160
8
14
NS160-250H-L /160
10-20
17-40
160
33
69
125
100
220
160
100
220
125 & 100M125
80
176
160 & 100M160
80
176
105
Additional characteristics
Protection
of switch-disconnectors (cont.)
INS/INV100 to 630 by Compact NS
circuit breaker or fuse
E88711
Interpact INS switch-disconnectors
Upstream protection
By circuit breaker
380/415 V
push
to
trip
90 %Ir
105
alarm
STR
23 SE
test
By circuit breaker
440/480 V (*)
By circuit breaker
500 V
By circuit breaker
525 V
By circuit breaker
690 V
By fuse
500 V
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type aM (1) max. rating (A)
Isc max.
making capacity
type gG (2) max. rating (A)
Isc max.
making capacity
type gG (1) max. rating (A)
Isc max.
making capacity
type BS (2) max. rating (A)
Isc max.
making capacity
type BS (1) max. rating (A)
Isc max.
making capacity
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
INS250-100
INV100
INS250-160
INV160
NS100-160-250N/100
25-36-36
53-75-75
NS100-160-250H/100
70
154
NS100-160-250L/100
150
330
NS100-160-250N/100
25-25-35
53-53-73
NS100-160-250H/100
65
143
NS100-160-250L/100
130
286
NS100-160-250N/100
18
36
NS100-160-250H/100
50
105
NS100-160-250L/100
100-70-70
220-154-154
NS100-160-250N/100
18
36
NS100-160-250H/100
35
73
NS100-160-250L/100
100-50-50
220-105-105
NS100-160-250N/100
8
14
NS100-160-250H/100
10
17
NS100-160-250L/100
75-20-20
165-40-40
100
100
220
80
100
220
100
100
220
80 and 63M80
80
176
250 and 200M250
80
176
NS160-250N/160
36
75
NS160-250H/160
70
154
NS160-250L/160
150
330
NS160-250N/160
35
73
NS160-250H/160
65
143
NS160-250L/160
130
286
NS160-250N/160
30
63
NS160-250H/160
50
105
NS160-250L/160
70
154
NS160-250N/160
22
46
NS160-250H/160
35
73
NS160-250L/160
50
105
NS160-250N/160
8
14
NS160-250H/160
10
17
NS160-250L/160
20
40
160
100
220
125
100
220
160
100
220
125 and 100M125
80
176
250 and 200M250
80
176
(*) Applicable for 480 V NEMA.
(1) Mandatory protection by an external thermal relay.
(2) No external thermal protection.
106
Schneider Electric
Additional characteristics
Protection
of switch-disconnectors (cont.)
INS/INV100 to 630 by Compact NS
circuit breaker or fuse
INS250-200
INV200
INS250
INV250
INS320
INV320
INS400
INV400
INS500
INV500
INS630
INV630
NS250N/200
36
75
NS250H/200
70
154
NS250L/200
150
330
NS250N/200
35
73
NS250H/200
65
143
NS250L/200
130
286
NS250N/200
30
63
NS250H/200
50
105
NS250L/200
70
154
NS250N/200
22
46
NS250H/200
35
73
NS250L/200
50
105
NS250N/200
8
14
NS250H/200
10
17
NS250L/200
20
40
200
100
220
160
100
220
200
100
220
160 and 100M160
80
176
250 and 200M250
80
176
NS250N/250
36
75
NS250H/250
70
154
NS250L/250
150
330
NS250N/250
35
73
NS250H/250
65
143
NS250L/250
130
286
NS250N/250
30
63
NS250H/250
50
105
NS250L/250
70
154
NS250N/250
22
46
NS250H/250
35
73
NS250L/250
50
105
NS250N/250
8
14
NS250H/250
10
17
NS250L/250
20
40
250
100
220
160
100
220
200
100
220
200 and 100M200
80
176
250 and 200M250
80
176
NS400-630N/320
45
94
NS400-630H/320
70
154
NS400-630L/320
150
330
NS400-630N/320
42
88
NS400-630H/320
65
143
NS400-630L/320
130
286
NS400-630N/320
30
63
NS400-630H/320
50
105
NS400-630L/320
100-70
220-154
NS400-630N/320
22
46
NS400-630H/320
35
73
NS400-630L/320
100-50
220-105
NS400-630N/320
10
17
NS400-630H/320
20
40
NS400-630L/320
75-35
165-73
320
100
220
250
100
220
320
100
220
250 and 200M250
80
176
355 and 315M355
80
176
NS400-630N/400
45
94
NS400-630H/400
70
154
NS400-630L/400
150
330
NS400-630N/400
42
88
NS400-630H/400
65
143
NS400-630L/400
130
286
NS400-630N/400
30
63
NS400-630H/400
50
105
NS400-630L/400
100-70
220-154
NS400-630N/400
22
46
NS400-630H/400
35
73
NS400-630L/400
100-50
220-105
NS400-630N/400
10
17
NS400-630H/400
20
40
NS400-630L/400
75-35
165-73
400
100
220
315
100
220
400
100
220
315 and 200M315
80
176
355 and 315M355
80
176
NS630N/500
45
94
NS630H/500
70
154
NS630L/500
150
330
NS630N/500
42
88
NS630H/500
65
143
NS630L/500
130
286
NS630N/500
30
63
NS630H/500
50
105
NS630L/500
70
154
NS630N/500
22
46
NS630H/500
35
73
NS630L/500
50
105
NS630N/500
10
17
NS630H/500
20
42
NS630L/500
35
73
500
100
220
400
100
220
500
100
220
400
80
176
450 and 400M450
80
176
NS630N/630
45
94
NS630H/630500
70
154
NS630L/630
150
330
NS630N/630
42
88
NS630H/630
65
143
NS630L/630
130
286
NS630N/630
30
63
NS630H/630
50
105
NS630L/630
70
154
NS630N/630
22
46
NS630H/630
35
73
NS630L/630
50
105
NS630N/630
10
17
NS630H/630
20
42
NS630L/630
35
73
500
100
220
500
100
220
630
100
220
500
80
176
450 and 400M450
80
176
Schneider Electric
107
E88712
Additional characteristics
Protection
of switch-disconnectors (cont.)
INS/INV630b to 2500 by Compact NS
circuit breaker or fuse
Interpact INS/INV switch-disconnectors
Upstream protection
By circuit breaker Compact NS
By circuit breaker
type / max. rating (A)
380/415 V
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
By circuit breaker
type / max. rating (A)
440/480 V (*)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
By circuit breaker
type / max. rating (A)
500 V/525 V
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
By circuit breaker
type / max. rating (A)
690 V
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
By fuse
By fuse
500V
Type aM (1) / max. rating (A)
Isc max.
making capacity
Type gG (2) / max. rating (A)
Isc max.
making capacity
Type gG (1) / max. rating (A)
Isc max.
making capacity
Type BS (2) / max. rating (A)
Isc max.
making capacity
Type BS (1) / max. rating (A)
Isc max.
making capacity
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
(*) Applicable for 480 V NEMA.
(1) Mandatory protection by an external thermal relay.
(2) No external thermal protection.
108
Schneider Electric
Additional characteristics
Protection
of switch-disconnectors (cont.)
INS/INV630b to 2500 by Compact NS
circuit breaker or fuse (cont.)
INS/INV630b
INS/INV800
INS/INV1000
INS/INV1250
INS/INV1600
INS/INV2000
INS/INV2500
NS630bN/630
50
105
NS630bH/630
50
105
NS630bL/630
150
330
NS630bN/630
50
105
NS630bH/630
50
105
NS630bL/630
130
286
NS630bN/630
40
84
NS630bH/630
50
105
NS630bL/630
100
220
NS630bN/630
30
63
NS630bH/630
42
88
NS630bL/630
25
53
NS800N/800
50
105
NS800H/800
50
105
NS800L/800
150
330
NS800N/800
50
105
NS800H/800
50
105
NS800L/800
130
286
NS800N/800
40
84
NS800H/800
50
105
NS800L/800
100
220
NS800N/800
30
63
NS800H/800
42
88
NS800L/800
25
53
NS1000N/1000
50
105
NS1000H/1000
50
105
NS1000L/1000
150
330
NS1000N/1000
50
105
NS1000H/1000
50
105
NS1000L/1000
130
286
NS1000N/1000
40
84
NS1000H/1000
50
105
NS1000L/1000
100
220
NS1000N/1000
30
63
NS1000H/1000
42
88
NS1000L/1000
25
53
NS1250N/1250
50
105
NS1250H/1250
50
105
–
–
–
NS1250N/1250
50
105
NS1250H/1250
50
105
–
–
–
NS1250N/1250
40
84
NS1250H/1250
50
105
–
–
–
NS1250N/1250
30
63
NS1250H/1250
42
88
–
–
–
NS1600N - NS1600bN/1600
50
105
NS1600H - NS1600bH/1600
50
105
–
–
–
NS1600N - NS1600bN/1600
50
105
NS1600H - NS1600bH/1600
50
105
–
–
–
NS1600N - NS1600bN/1600
40
84
NS1600H - NS1600bH/1600
50
105
–
–
–
NS1600bN/1600
30
63
NS1600bH/1600
42
88
–
–
–
NS2000N/2000
50
105
NS2000H/2000
50
105
–
–
–
NS2000N/2000
50
105
NS2000H/2000
50
105
–
–
–
NS2000N/2000
50
105
NS2000H/2000
50
105
–
–
–
NS2000N/2000
50
105
NS2000H/2000
50
105
–
–
–
NS2500N/2500
50
105
NS2500H/2500
50
105
–
–
–
NS2500N/2500
50
105
NS2500H/2500
50
105
–
–
–
NS2500N/2500
50
105
NS2500H/2500
50
105
–
–
–
NS2500N/2500
50
105
NS2500H/2500
50
105
–
–
–
630
100
220
630
100
220
1250
100
220
630
80
176
1250
80
176
800
100
220
630
100
220
1250
100
220
630
80
176
1250
80
176
1000
100
220
800
100
220
1250
100
220
800
80
176
1250
80
176
1250
100
220
1000
100
220
1250
100
220
1000
80
176
1250
80
176
1250
100
220
1250
100
220
1250
100
220
1250
80
176
1250
80
176
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Schneider Electric
–
–
–
–
–
–
–
–
–
109
Additional characteristics
Protection
of switch-disconnectors (cont.)
INS/INV630b to 2500 by Masterpact
circuit breakers NT and NW
E88713
Interpact INS/INV switch-disconnectors
Upstream protection
I
O
push
ON
push
OFF
rged
discha
O OFF
By Masterpact circuit breaker NT H1
By circuit breaker
type / max. rating (A)
220/690 V
Isc max.
making capacity
By Masterpact circuit breaker NT L1
By circuit breaker
type / max. rating (A)
220/525 V
Isc max.
making capacity
By circuit breaker
type / max. rating (A)
690 V
Isc max.
making capacity
By Masterpact circuit breaker NW N1-H1-H2-H3
By circuit breaker
type / max. rating (A)
220/440-480 V (*)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
By circuit breaker
type / max. rating (A)
500 V/525 V
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
By circuit breaker
type / max. rating (A)
690 V
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
type / max. rating (A)
Isc max.
making capacity
By Masterpact circuit breaker NW L1
By circuit breaker
type / max. rating (A)
220/690 V
Isc max.
making capacity
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
kA rms.
kA peak
DIN OFF / DIN ON
DIN OFF / DIN ON
(*) Applicable for 480 V NEMA.
110
Schneider Electric
Additional characteristics
Protection
of switch-disconnectors (cont.)
INS/INV630b to 2500 by Masterpact
circuit breakers NT and NW (cont.)
INS/INV630b
INS/INV800
INS/INV1000
INS/INV1250
INS/INV 1600
INS/INV2000
INS/INV2500
NT08H1/630
43
88
NT08H1/800
42
88
NT10H1/1000
42
88
NT12H1/1000
42
88
NT16H1/1600
42
88
–
–
–
–
–
–
NT08L1/630
100
220
NT08L1/630
25
53
NT08L1/800
100
220
NT08L1/800
25
53
NT10L1/1000
100
220
NT10L1/1000
25
53
NT12L1/1250
100
220
NT12L1/1250
25
53
NT16L1/1600
100
220
NT16L1/1600
25
53
–
–
–
–
–
–
–
–
–
–
–
–
NW08/N1/630
42
88
NW08H1/630
50
105
NW08H2/630
50
105
–
–
–
NW08/N1/630
42
88
NW08H1/630
50
105
NW08H2/630
50
105
–
–
–
NW08/N1/630
50
105
NW08H1/630
50
105
NW08H2/630
50
105
–
–
–
NW08/N1/800
42
88
NW08H1/800
50
105
NW08H2/800
50
105
–
–
–
NW08/N1/800
42
88
NW08H1/800
50
105
NW08H2/800
50
105
–
–
–
NW08/N1/800
50
105
NW08H1/800
50
105
NW08H2/800
50
105
–
–
–
NW10N1/1000
42
88
NW10H1/1000
50
105
NW10H2/1000
50
105
–
–
–
NW10N1/1000
42
88
NW10H1/1000
50
105
NW10H2/1000
50
105
–
–
–
NW10N1/1000
50
105
NW10H1/1000
50
105
NW10H2/1000
50
105
–
–
–
NW12N1/1250
42
88
NW12H1/1250
50
105
NW12H2/1250
50
105
–
–
–
NW12N1/1250
42
88
NW12H1/1250
50
105
NW12H2/1250
50
105
–
–
–
NW12N1/1250
50
105
NW12H1/1250
50
105
NW12H2/1250
50
105
–
–
–
NW16N1/1600
42
88
NW16H1/1600
50
105
NW16H2/1600
50
105
–
–
–
NW16N1/1600
42
88
NW16H1/1600
50
105
NW16H2/1600
50
105
–
–
–
NW16N1/1600
50
105
NW16H1/1600
50
105
NW16H2/1600
50
105
–
–
–
–
–
–
NW20H1/2000
50
105
NW20H2/2000
50
105
NW20H3/2000
50
105
–
–
–
NW20H1/2000
50
105
NW20H2/2000
50
105
NW20H3/2000
50
105
–
–
–
NW20H1/2000
50
105
NW20H2/2000
50
105
NW20H3/2000
50
105
–
–
–
NW25H1/2500
50
105
NW25H2/2500
50
105
NW25H3/2500
50
105
–
–
–
NW25H1/2500
50
105
NW25H2/2500
50
105
NW25H3/2500
50
105
–
–
–
NW25H1/2500
50
105
NW25H2/2500
50
105
NW25H3/2500
50
105
NW08L1/630
50
105
NW08L1/800
50
105
NW10L1/1000
50
105
NW12L1/1250
50
105
NW16L1/1600
50
105
NW20L1/2000
50
105
–
–
–
Schneider Electric
111
112
Schneider Electric
Catalogue numbers
Schneider Electric
Presentation
Functions and characteristics
Installation recommandations
Dimensions and connection
Additional characteristics
2
17
63
85
103
INS40 to 160
114
Complete fixed/FC device and accessories
Accessories
114
115
INS250-100 to 630
117
Complete fixed/FC device and accessories
117
INV100 to 630
118
Complete fixed/FC device and specific accessories
118
INS250-100 to 250 and INV100 to 250
119
Accessories
119
INS320 to 630 and INV320 to 630
122
Accessories
122
INS630b to 2500
124
Complete fixed/FC device and accessories
124
INV630b to 2500
125
Complete fixed/FC device and specific accessories
125
INS630b to 2500 and INV630b to 2500
126
Accessories
126
113
Catalogue numbers
INS40 to 160
Complete fixed/FC device and
accessories
Interpact INS40 to 160 standard version with black handle
Interpact INS40
Interpact INS63
Interpact INS80
3P
28900
28902
28904
4P
28901
28903
28905
Interpact INS100
Interpact INS125
Interpact INS160
3P
28908
28910
28912
4P
28909
28911
28913
Interpact INS40
Interpact INS63
Interpact INS80
3P
28916
28918
28920
4P
28917
28919
28921
Interpact INS100
Interpact INS125
Interpact INS160
3P
28924
28926
28928
4P
28925
28927
28929
.2
.1
E33366
E33365
.4
Interpact INS40 to 160 with red handle and yellow front
.2
.1
E33366
E33365
.4
Individual enclosures
IP55 heavy-duty sheetmetal enclosure
E90492
For INS40 to INS160 with extended standard rotary handle
For INS40 to INS160 with extended red handle on yellow front
31208
31209
For INS40 to INS160 with extended standard rotary handle
For INS40 to INS160 with extended red handle on yellow front
28967
28968
N
E32419
IP55 heavy-duty insulating enclosure
Connection accessories
Distribloc distribution block (for bare cables)
E33404
INS40 to 125
INS100 to 160
125 A, 12 outgoing spring terminals (7 x 4 mm2 + 3 x 6 mm2
+ 2 x 10 mm2) + 1 outgoing tunnel terminal (25 mm2)
160 A, 12 outgoing spring terminals (7 x 4 mm2 + 3 x 6 mm2
+ 2 x 10 mm2) + 1 outgoing tunnel terminal (25 mm2) with
prefabricated connections
(2)
07105
(2)
07106
125 A, 4 x 10 holes (5 x 10 mm2 + 4 x 16 mm2 + 1 x 35 mm2)
125 A, 4 x 17 holes (8 x 10 mm2 + 8 x 16 mm2 + 1 x 35 mm2)
(2)
13512
13514
E26801
Multi-stage distribution block (for bare cables)
INS40 to 125
INS40 to 125
(2)
Connectors for bare Cu or Al cables
INS100 to 160 S < 95 mm2
Set of 3
Set of 4
28947
28948
Distribution connector for
3 rigid cables up to 16 mm2 or
3 flexible cables up to 10 mm2
INS40 to 80
Set of 3
Set of 4
19096
19091
Distribution connector for
4 rigid cables up to 25 mm2 or
4 flexible cables up to 16 mm2
INS100 to 160
Set of 3
Set of 4
28949
28950
E30707
E39432
E32424
Snap-on
(2) Product sold by MGA
308E6010.fm/114
2 août 2002 10:15
Schneider Electric
Catalogue numbers
INS40 to 160 (cont.)
Accessories
Connection accessories (cont.)
E27797
Crimp lugs for copper cables
For 95 mm2 cables with
interphase barriers
INS100 to 160
Set of 3
Set of 4
28951
28952
INS40 to 80
INS100 to 160
3P/4P
3P/4P
Set of 2
Set of 2
28955
28956
INS40 to 80
INS100 to 160
3P/4P
3P/4P
Set of 2
Set of 2
28957
28958
INS100 to 160
3P/4P
Set of 6
28959
E24075
Terminal shrouds
E32457
Terminal shields
E88893
Interphase barriers
E94206
E94166
Special connection accessories for INS100DC
Terminal extensions for series or parallel connection of two poles (1)
1 terminal ext.
(1) Series connection of:
2 poles = 1 terminal extension
3 poles = 2 terminal extensions
4 poles = 3 terminal extensions
Parallel connection of:
2 poles = 2 terminal extensions
3 poles = set of 2 terminal extensions (29499)
4 poles = 4 terminal extensions
Terminal extensions for parallel connection of three poles
Set of 2 terminal
extensions
4P terminal shields for series connection of poles
Set of 1
4P terminal shields for parallel connection of poles (2P/4P)
Set of 1
29498
1 OF / CAF / CAO (standard)
1 OF / CAF / CAO (low level)
INS40 to 160
INS40 to 160
29450
29452
29499
29496
29497
Electrical auxiliaries
E18608
Auxiliary contacts
Rotary handles
Accessories for conversion to extended rotary handles
E33405
Front control
E51011
Lateral control
Schneider Electric
Lateral control on G, GX or
PRAGMA F functional enclosure
2 août 2002 10:15
Black handle
Red handle
on yellow front
Black handle
Red handle on yellow front (1)
Black handle
INS40 to 160
INS40 to 160
28941
28942
INS40 to 160
INS40 to 160
INS40 to 160
28943
28944
28945
Red handle on yellow front (1)
INS40 to 160
28946
308E6010.fm/115
Catalogue numbers
INS40 to 160 (cont.)
Accessories (cont.)
Locking and interlocking
Handle locking
.4
.2
.1
Built-in
N
E32426
By 1 to 3 padlocks (OFF position), hasp dia. 5 to 8 mm, or by lead seals
Ø5
5
88
E89637
Interlocking for extended rotary handles
Mechanical
28953
Black handle
Red handle (1)
28962
28963
¿5...8
Spare parts
.1
N
E32411
.2
.4
or
(1) For red/yellow switch versions only.
308E6010.fm/116
2 août 2002 10:15
Schneider Electric
Catalogue numbers
INS250-100 to 630
Complete fixed/FC device and
accessories
3P
31100
31104
31102
31106
4P
31101
31105
31103
31107
Interpact INS320
Interpact INS400
Interpact INS500
Interpact INS630
3P
31108
31110
31112
31114
4P
31109
31111
31113
31115
E50995
Interpact INS250-100A
Interpact INS250-160A
Interpact INS250-200A
Interpact INS250
3P
31120
31124
31122
31126
4P
31121
31125
31123
31127
Interpact INS320
Interpact INS400
Interpact INS500
Interpact INS630
3P
31128
31130
31132
31134
4P
31129
31131
31133
31135
3P
31140
31144
31142
31146
31148
31150
31152
31154
4P
31141
31145
31143
31147
31149
31151
31153
31155
3P
29358
4P
29359
29324
32620
32565
E50996
E50995
Interpact INS250-100A
Interpact INS250-160A
Interpact INS250-200A
Interpact INS250
E50996
Interpact INS250 to 630 standard version with black handle
Interpact INS250 to 630 with red handle and yellow front
Source changeover systems
Complete assembly
E89638
With Interpact INS250-100A
With Interpact INS250-160A
With Interpact INS250-200A
With Interpact INS250
With Interpact INS320
With Interpact INS400
With Interpact INS500
With Interpact INS630
Downstream coupling accessories
E50998
For Interpact INS250
Long downstream 3P/4P terminal shields (set of 2)
For Interpact INS320 to 630
Long downstream 3P/4P terminal shields (set of 2)
32619
Individual enclosures
IP55 heavy-duty sheetmetal enclosure
E90492
For INS250-100 to 250 with extended standard rotary handle
For INS250-100 to 250 with extended red rotary handle on yellow front
For INS320 to 630 with extended standard rotary handle
For INS320 to 630 with extended red rotary handle on yellow front
31210
31211
31212
31213
N
E32419
IP55 heavy-duty insulating enclosure
Schneider Electric
For INS250-100 to 250 with extended standard rotary handle
For INS250-100 to 250 with extended red rotary handle on yellow front
For INS320 to 630 with extended standard rotary handle
For INS320 to 630 with extended red rotary handle on yellow front
2 août 2002 10:15
31204
31205
31206
31207
308E6010.fm/117
Catalogue numbers
INV100 to 630
Complete fixed/FC device and
specific accessories
E51002
E51001
Interpact INV100 to 630 standard version with black handle
Interpact INV100
Interpact INV160
Interpact INV200
Interpact INV250
3P
31160
31164
31162
31166
4P
31161
31165
31163
31167
Interpact INV320
Interpact INV400
Interpact INV500
Interpact INV630
3P
31168
31170
31172
31174
4P
31169
31171
31173
31175
Interpact INV100
Interpact INV160
Interpact INV200
Interpact INV250
3P
31180
31184
31182
31186
4P
31181
31185
31183
31187
Interpact INV320
Interpact INV400
Interpact INV500
Interpact INV630
3P
31188
31190
31192
31194
4P
31189
31191
31193
31195
E51002
E51001
Interpact INV100 to 630 with red handle and yellow front
Individual enclosures
For INV100 to 250 with extended standard rotary handle
For INV100 to 250 with extended red rotary handle on yellow front
For INV320 to 630 with extended standard rotary handle
For INV320 to 630 with extended red rotary handle on yellow front
N
E32419
IP55 heavy-duty insulating enclosure
31204
31205
31206
31207
E89642
Combination with Compact NS devices for "tarif jaune / tarif vert"
INV100 to 250 combination with NS250
INV320 to 630 combination with NS250
Front alignment base for INV320 to 630 combination with NS250
INV320 to 630 combination with NS400/630
31066
31067
31064
31068
Flexible connection assembly for vertical INV100 to 250 with horizontal NS250
Flexible connection assembly for vertical INV320 to 630 with horizontal NS250
Flexible connection assembly for vertical INV100 to 250 with vertical NS250 beside
Flexible connection assembly for vertical INV320 to 630 with vertical NS400/630 beside
Flexible connection assembly for vertical INV320 to 630 with vertical NS250 beside
31069
31092
31071
31072
31093
E89641
¿5...8
308E6010.fm/118
2 août 2002 10:15
Schneider Electric
Catalogue numbers
INS250-100 to 250 and INV100 to 250
Accessories
Connection accessories
Rear connections
E18579
Short (1 pair)
Long (1 pair)
29235
29236
Bare cable connectors
E18598
E18572
Snap-on, for cables:
1.5 to 95 mm2 ; < 160 A
10 to 185 mm2 ; < 250 A
Tab connector for voltage tap on 185 mm2bare cable connector
Clip for bare cable connector
Distribution connector for six 1.5 to 35 mm2 cables with
interphase barriers
Set of 3
Set of 4
Set of 3
Set of 4
Set of 2
Set of 10
Set of 3
Set of 4
29242
29243
29259
29260
29348
29241
29248
29249
E24076
Polybloc distribution block (for bare cables)
160 A (40°C), for 6 cables up to < 10 mm2
250 A (40°C), for 6 cables up to < 10 mm2
* consult us
(2)
(2)
07100
07101
E18601
E18600
Terminal extensions (supplied with 2 or 3 interphase barriers)
Right-angle terminal extensions
Set of 3
Set of 4
29261
29262
Straight terminal extensions
Set of 3
Set of 4
29263
29264
Spreaders (for upstream or downstream connection)
3P
4P
31563
31564
One-piece
Front alignment base for onepiece spreader
3/4P
3/4P
31061
31064
E51006
E18599
Separate for each pole
Crimp lugs for copper cables (supplied with 2 or 3 interphase barriers)
E18602
For 120 mm2 cables
For 150 mm2 cables
For cable 185 mm2 cables
Set of 3
Set of 4
Set of 3
Set of 4
Set of 3
Set of 4
29252
29256
29253
29257
29254
29258
Set of 3
Set of 4
Set of 3
Set of 4
29504
29505
29506
29507
Set of 2
Set of 2
29322
29324
Set of 6
29329
Crimp lugs for aluminium cables (supplied with 2 or 3 interphase barriers)
E30908
For 150 mm2 cables
For 185 mm2 cables
E51007
Terminal shields
Short
Long
3/4 P
3/4 P
E18606
Interphase barriers
(2) Product sold by MGA
Schneider Electric
2 août 2002 10:15
308E6010.fm/119
Catalogue numbers
INS250-100 to 250 and INV100 to 250
(cont.)
Accessories (cont.)
Special connection accessories for INS100DC
E94206
E94166
Terminal extensions for series or parallel connection of two poles (1)
1 terminal ext.
(1) Series connection of:
2 poles = 1 terminal extension
3 poles = 2 terminal extensions
4 poles = 3 terminal extensions
Parallel connection of:
2 poles = 2 terminal extensions
3 poles = set of 2 terminal extensions (29499)
4 poles = 4 terminal extensions
Terminal extensions for parallel connection of three poles
Set of 2 terminal
extensions
4P terminal shields for series connection of poles
Set of 1
4P terminal shields for parallel connection of poles (2P/4P)
Set of 1
29498
29499
29496
29497
Electrical auxiliaries
Auxiliary contacts (changeover type)
E18608
OF or CAM (early make or break)
Low level OF or CAM (early make or break)
29450
29452
Indication and measurement modules
E51008
Ammeter module (4P)
Adaptation kit (necessary for devices with direct front handles)
Rating (A)
100
150
250
16
A
12
8
4
0
160/5
31081
29456
30556
31566
Current transformer module (4P)
E51009
Rating (A)
100
150
250
29458
30558
31568
Rotary handles
Extended front control
E33405
For INS250 with standard rotary handle
For INS250 with red handle on yellow front (1)
For complete source changeover assembly
31050
31051
31055
Lateral control
E89607
Direct lateral control for INS and INV250
Lateral support
+ standard lateral control assembly
or + red and yellow lateral control assembly (1)
Extended lateral control for INS and INV250
Standard lateral control assembly
Red and yellow lateral control assembly (1)
31054
31057
31058
31057
31058
Locking and interlocking for INS/INV and source changeover systems
E51012
Locking for INS/INV
Handle locking by 1 to 3 padlocks (in OFF position)
By keylock
Keylocking device
+ Ronis 1351B.500 keylock
or + Profalux KS5 B24 D4Z keylock
fl
fl
Built-in
31087
41940
42888
Locking for INS complete source changeover assembly
E42629
Handle locking by 1 to 3 padlocks (in OFF position)
By keylock
Keylocking device
+ Ronis 1351B.500 keylock
or + Profalux KS5 B24 D4Z keylock
Built-in
31097
41940
42888
E50997
Interlocking for INS/INV with direct or extended rotary handle
¿5...8
¿5...8
¿5...8
Mechanical interlocking for INS250
By keylock
Keylocking device
+ Ronis 1351B.500 keylock (2 keylocks / 1 key)
or + Profalux KS5 B24 D4Z keylock (1 keylocks / 1 key)
2x
31073
31087
41950
42878
(1) For red/yellow switch versions only.
308E6010.fm/120
2 août 2002 10:15
Schneider Electric
Catalogue numbers
INS250-100 to 250 and INV100 to 250
(cont.)
Accessories (cont.)
Installation accessories
Front panel escutcheons
E18591
For INS/INV
For ammeter module, IP40
31079
29318
Lead seal accessories
29375
Spare parts
12 snap-in nuts for fixed/FC(M8)
100 identification labels
Bag of screws
Black handle
Red handle (1)
Viewport for INV100/160/250
(1) For red/yellow switch versions only.
Schneider Electric
2 août 2002 10:15
30554
29314
29312
31082
31083
31089
308E6010.fm/121
Catalogue numbers
INS320 to 630 and INV320 to 630
Accessories
Connection accessories
E18579
Rear connections
Short (1 pair)
Long (1 pair)
32475
32476
E22041
E22040
Bare cable connectors
For 1 cable, 35 mm2 to 300 mm2
Set of 3
Set of 4
Set of 3
Set of 4
Set of 2
32479
32480
32481
32482
29348
Right-angle terminal extensions
Set of 3
Set of 4
32484
32485
Edgewise terminal extensions
Set of 3
Set of 4
32486
32487
For 2 cables, 35 mm2 to 240 mm2
Tab connector for voltage tap on bare cable connector
E21276
E18600
Terminal extensions (supplied with 2 or 3 interphase barriers)
Spreaders (for upstream or downstream connection)
E18599
One-piece
52.5 mm
70 mm
3P
4P
3P
4P
32490
32491
32492
32493
Crimp lugs for copper cables (supplied with 2 or 3 interphase barriers)
E18602
For 240 mm2 cables
For 300 mm2 cables
Set of 3
Set of 4
Set of 3
Set of 4
32500
32501
32502
32503
Set of 3
Set of 4
Set of 3
Set of 4
32504
32505
32506
32507
Set of 2
Set of 2
Set of 2
32563
32565
32583
Set of 6
32570
1 terminal ext.
32868
Set of 1
Set of 1
32866
32867
Crimp lugs for aluminium cables (supplied with 2 or 3 interphase barriers)
E30908
For 240 mm2 cables
For 300 mm2 cables
E51007
Terminal shields
Short
Long
Long for 52.5 mm spreader (supplied with insulating plate)
3/4P
3/4P
3/4P
E89622
Interphase barriers
E94207
Special connection accessories for INS320 to 630DC
308E6010.fm/122
Terminal extensions for series or parallel connection of two poles (1)
(1) Series connection of:
2 poles = 1 terminal extension
3 poles = 2 terminal extensions
4 poles = 3 terminal extensions
Parallel connection of:
2 poles = 2 terminal extensions
4 poles = 4 terminal extensions
4P terminal shields for series connection of poles
4P terminal shields for parallel connection of poles
2 août 2002 10:15
Schneider Electric
Catalogue numbers
INS320 to 630 and INV320 to 630
(cont.)
Accessories (cont.)
Electrical auxiliaries
Auxiliary contacts (changeover type)
E18608
OF or CAM (early make or break)
OF or CAM low level (early make or break)
29450
29452
Indication and measurement modules
Ammeter module (4P)
E51008
Rating (A)
400
600
32656
32856
400
600
32658
32858
16
A
12
8
4
0
160/5
Current transformer module (4P)
E51009
Rating (A)
Rotary handles
Extended front control
E89617
For INS320/400/630 with standard rotary handle
For INS320/400/630 with red handle on yellow front (1)
For complete source changeover assembly
31052
31053
31055
Locking and interlocking for INS/INV and source changeover systems
Locking for INS/INV
E89618
Handle locking by 1 to 3 padlocks (in OFF position)
By keylock
Keylocking device
+ Ronis 1351B.500 keylock
or + Profalux KS5 B24 D4Z keylock
Built-in
31088
41940
42888
Locking for INS complete source changeover assembly
E42629
Handle locking by 1 to 3 padlocks (in OFF position)
By keylock
Keylocking device
+ Ronis 1351B.500 keylock
or + Profalux KS5 B24 D4Z keylock
Built-in
31097
41940
42888
Interlocking for INS/INV with direct or extended rotary handle
E89624
Mechanical interlocking for INS320/400/630
By keylock
Keylocking device
+ Ronis 1351B.500 keylock (1 keylocks / 1 key)
or + Profalux KS5 B24 D4Z keylock (1 keylocks / 1 key)
¿5...8
2x
31074
31088
41950
42878
Installation accessories
Front panel escutcheons
E18591
For INS/INV
For ammeter module, IP40
31080
29318
Lead seal accessories
29375
Spare parts
100 labels
Bag of screws
Black handle
Red handle (1)
Viewport for INV320/400/630
(1) For red/yellow switch versions only.
Schneider Electric
2 août 2002 10:15
29314
32552
31084
31085
31090
308E6010.fm/123
Catalogue numbers
INS630b to 2500
Complete fixed/FC device and
accessories
Interpact INS630b
Interpact INS800
Interpact INS1000
Interpact INS1250
Interpact INS1600
Interpact INS2000
Interpact INS2500
3P
31342
31330
31332
31334
31336
31338
31340
4P
31343
31331
31333
31335
31337
31339
31341
3P
31356
31344
31346
31348
31350
4P
31357
31345
31347
31349
31351
E89623
E88699
Interpact INS630b to 2500 standard version with black handle
E88699
Interpact INS630b to 2500 with red handle and yellow front
308E6010.fm/124
Interpact INS630b
Interpact INS800
Interpact INS1000
Interpact INS1250
Interpact INS1600
2 août 2002 10:15
Schneider Electric
Catalogue numbers
INV630b to 2500
Complete fixed/FC device and
specific accessories
Interpact INV630b
Interpact INV800
Interpact INV1000
Interpact INV1250
Interpact INV1600
Interpact INV2000
Interpact INV2500
3P
31370
31358
31360
31362
31364
31366
31368
4P
31371
31359
31361
31363
31365
31367
31369
3P
31387
31372
31374
31376
31378
4P
31388
31373
31375
31377
31379
3P
31385
4P
31386
31317
31318
E89640
E89639
Interpact INV630b to 2500 standard version with black handle
E89639
Interpact INV630b to 2500 with red handle and yellow front
Interpact INV630b
Interpact INV800
Interpact INV1000
Interpact INV1250
Interpact INV1600
E89619
Combination with Compact NS devices (for "tarif vert")
Schneider Electric
INV630b/1000/1250/1600 combination with
NS800/1000/1250/1600
INV2000/2500 combination with NS2000/2500
2 août 2002 10:15
308E6010.fm/125
Catalogue numbers
INS630b to 2500 and
INV630b to 2500
Accessories
Connection accessories
Vertical connection adapters
3P
4P
Set of 3
Set of 4
31301
31302
INS/INV630b/1600
3P
4P
Set of 3
Set of 4
33644
33645
INS/INV630b/1600
3P
4P
Set of 3
Set of 4
31305
31306
E88701
INS/INV630b/1600
E88702
Cable lug adapters
E88703
Spreaders
Insulation accessories
Base for terminal shield (incompatible avec séparateur de phases)
E88704
INS/INV630b/1600
3P
4P
31307
31308
3P
4P
33628
33629
Terminal shield (nécessite l’embase)
E88705
INS/INV630b/1600
Interphase barriers (incompatible avec embase et cache-raccordement)
E89625
INS/INV630b/1600
INS/INV2000/2500
3P/4P
3P/4P
Set of 6
Set of 6
31315
31319
Electrical auxiliaries
E18608
Auxiliary contacts (changeover type)
OF or CAM (early make or break)
OF or CAM low level (early make or break)
29450
29452
Extended front control
E88708
INS630b/1600
INS2000/2500
For standard rotary handle
For red handle on yellow front (1)
For standard rotary handle
31286
31287
31288
Locking and interlocking
E89620
Locking for INS/INV630b to 1600
Handle locking by 1 to 3 padlocks (in OFF position)
By keylock
Keylocking device
+ Ronis 1351B.500 keylock
or + Profalux KS5 B24 D4Z keylock
Built-in
31291
41940
42888
Interlocking for INS/INV630b to 1600
E89626
By keylock
Keylocking device
+ Ronis 1351B.500 keylock (1 keylocks / 1 key)
or + Profalux KS5 B24 D4Z keylock (1 keylocks / 1 key)
2 x 31291
41950
42878
(1) For red/yellow switch versions only.
308E6010.fm/126
2 août 2002 10:15
Schneider Electric
Catalogue numbers
INS630b to 2500 and
INV630b to 2500 (cont.)
Accessories (cont.)
Installation accessories
Escutcheon
3P/4P
31295
E88707
INS630b/1600
Lead seal accessories
31316
Spare parts
E88709
INS630b/1600 and INV630b
INS2000/2500 and INV2000/2500
E88700
Viewport for INV630b/2500
Black handle
Red handle (1)
Black handle
31296
31297
31298
3P
4P
31293
31294
(1) For red/yellow switch versions only.
Schneider Electric
2 août 2002 10:15
308E6010.fm/127
89 boulevard Franklin Roosevelt
F - 92500 Rueil Malmaison (France)
Tél : +33 (0)1 41 29 85 00
http://www.schneiderelectric.com
DBTP308E
As standards, specifications and designs change from time to time, please ask for confirmation
of the information given in this publication.
This document has been printed
on ecological paper.
Design: Schneider Electric - Ameg
Photo: Schneider Electric
Printed:
07-2002
ABTED00000EN © 2002 Schneider Electric - All right reserved
Schneider Electric Industries SAS