YAKIMA JAIL SHOWER ANNEX RENOVATION
YAKIMA, WASHINGTON
DLR Group Project 73-10126-01
ADDENDUM CC2
ADDENDUM CC2
DLR GROUP
51 University Street Suite 600
Seattle, WA 98101
P 206-461-6000
F 206-461-6049
March 18, 2016
NOTICE TO BIDDERS: Amend the contract documents to the above referenced project as
follows:
DRAWINGS
ITEM NO. 1 SHEET A0.1 – SPECIFICATIONS AND GENERAL NOTES
A.
REPLACE sheet A0.1 in its entirety for specification changes to interior painting,
warranty for seamless system, wet film test for seamless system, and demolition notes
for ceramic tile base in shower and toilet areas.
ITEM NO. 2 SHEET A1.1 – ENLARGED PLANS – FIRST FLOOR AND MEZZANINE
A.
REPLACE sheet A1.1 in its entirety to indicate walls to be included in interior painting
in all floor plans.
ITEM NO. 3 SHEET A3.1
A.
REPLACE sheet A3.1 in its entirety to indicate ceilings to be included in interior
painting.
CLARIFICATIONS
ITEM NO. 4
A.
Refer to attached sign in sheet from pre-bid walk through on March 8, 2016.
ITEM NO. 5
A.
AVAILABLE POWER
Power available in each unit is one (1) circuit of 208 volt 3 phase 40amp (for spray rig)
and three (3) circuits of 120 volt 1 phase 20amp circuits (for hand tools).
ITEM NO. 6
A.
PRE-BID WALK THROUGH SIGN IN SHEET
OWNER WORK CONCURRENT TO SCOPE OF WORK
Owner intends to complete interior painting of existing furniture in each unit as it is
cleared for shower renovation. Contractor shall be aware of concurrent work
throughout the unit, but not located in the area of the showers.
ADDENDUM CC2
CC2-1
YAKIMA JAIL SHOWER ANNEX RENOVATION
YAKIMA, WASHINGTON
DLR Group Project 73-10126-01
ADDENDUM CC2
SUBSTITUTION REQUEST REVIEW (prebid)
Approval applies to specific product substitution only and does not relieve the Contractor/
Supplier from the responsibility of meeting all applicable requirements of the Plans and
Specifications. “Yes” indicates that the substitution request is accepted; “No” indicates that it is
NOT accepted, and “Pending” indicates that evaluation of the substitution request is pending.
The following representatives and manufacturers have further agreed upon the following:
1. The proposed substitution does not affect dimensions shown on the Drawings.
2. The proposer will pay for changes to the building design, including engineering design,
detailing, and construction costs caused by the requested substitution.
3. The proposed substitution will have no adverse effect on other trades, the construction
schedule, or specified warranty requirements.
4. Maintenance and service parts will be locally available for the proposed substitution.
5. The proposed substitution function, appearance, and quality are equivalent or superior to
the specified item.
SECTION
SECTION TITLE
PROPOSED / ADDED
MANUFACTURER
ACCEPTED?
A0.1
Interior Lighting / Paragraph H
Kenall
Yes with
exceptions *
A0.1
Seamless Shower Renovation
Finish System
Milamar
No
A0.1
Interior Lighting / Paragraph H
Eaton Lighting Fail Safe
Yes with
exceptions **
Exceptions:
*Provide Kenall fixture with lens thickness to match basis of design. Contactor is responsible for
clearance inside soffit without lowering soffit height for revised fixture depth.
** Provide 4’-0” length fixture. Outer lens -86 shall be 0.250 clear polycarbonate.
END OF ADDENDUM CC2
ADDENDUM CC2
CC2-2
ICO Guard
Coating
Product Data Sheet
Product Description
ICO-Guard Coating™ is a two part, 100% solids, epoxy
coating primarily for protecting concrete surfaces in
corrosive environments. It is a USDA approved material,
with zero VOC’s, no odor, and excellent color stability. It is
our highest chemical resistant, bisphenol A epoxy coating,
resisting moderate to high concentrations of inorganic
acids, caustics and some solvents. With a tensile elongation
of 9%, it is a flexibilized coating that withstands impact and
thermal shock far better than conventional, more brittle
epoxy coatings. ICO Guard Coating has excellent damp, as
well as dry adhesion to most substrates. No primer is
needed. It is normally applied 10-20 mils per coat,
depending on substrate. Two thinner coats are preferred
to one thick coat to minimize entrapped air.
ICO Guard Coating can be ordered in a fast cure version, ICO
Guard Coating FC, for faster turnaround times and for
applications down to 40°F, while our ICO Guard Coating XFC
can cure down to 32°F. Note that both of these fast cure
versions, if applied below 50°F, are prone to whitening
under hot water wash-downs, so they should be top coated
with our more color stable ICO Ure Guard 100,
polyurethane coating.
cleaners. See our Chemical Resistance Chart under “ICO
Guard” for complete chemical resistance.
Physical Properties
Tensile Strength
(ASTM D-638):
Tensile
Elongation (D638):
Flexural
Strength (D790):
Hardness, Shore
D (D-2240):
1560
psi
Gardner Impact
Strength (D-2794):
80 in lbs.
9%
Bond Strength to
Quarry Tile:
>1000 psi
60° Gloss
100
4140
psi
80
Vapor
Transmission Rate
(E-96):
Water Absorption
(D-570):
Taber Abrasion (D1044) <CS17,
1000g, 1000
cycles>:
.03 perms
0.2% in 24
hrs.
105 mg. loss
Physical Characteristics
Part A:
Part B:
A&B Mixed:
Density, lbs./gal
15.4
8.6
13
Part A:
Part B:
A&B Mixed:
Viscosity @ 77°F, cps
5500
300
2000
Product Application
ICO-Guard Coating™ is normally the top coat used in
conjunction with our ICO Guard resin system applied by
slurry, then seeded to refusal with aggregate to build up to
the desired ¼” thickness. It can also be used as an optional
top coat over our ICO Guard 51 trowelled material ICOGuard Coating™ is normally the top coat used in
conjunction with our ICO Guard resin system applied by
slurry, then seeded to refusal with aggregate to build up to
the desired ¼” thickness. It can also be used as an optional
top coat over our ICO Guard 51 trowelled material.
Chemical Resistance
ICO-Guard Coating™ has excellent chemical resistance to a
wide variety of inorganic acids, holding up to 10% acetic,
concentrated citric, 37% hydrochloric, 80% lactic, 85%
phosphoric and 80% sulfuric acid, as well as most CIP
Mixing Ratios
Part A : Part B:
Part A : Part B, FC:
Part A : Part B, XFC:
By Volume
2.5:1
3.8:1
3.3:1
By Weight
4.5:1
7:1
5.6:1
Color Availability:
Standard Colors: White, Gray, Dark Gray, Beige, Yellow, Red,
Green, blue, Brown, & Black
Shelf Life: 1 year at 77°F in unopened containers.
4.
Packaging and Coverage Rates
1 gallon kit:
160 SF
4 gallon kit:
640 SF
100 gallon drum kit:
16,000 SF
Curing Times @
Pot
Life:
Work
Time:
ICO
Tack
Guard
Free:
Coating
Hard,
Foot:
Hard,
Truck:
Pot
Life:
Work
Time:
ICO
Guard
Tack
Coating Free:
FC
Hard,
Foot:
Hard,
Truck:
Pot
Life:
Work
Time:
ICO
Guard
Tack
Coating Free:
XFC
Hard,
Foot:
Hard,
Truck:
32°F
40°F
---
---
---
---
---
---
---
---
---
---
----------20
min.
18
min.
16
hrs.
30
hrs.
36
hrs.
20
min.
35
min.
16
hrs.
26
hrs.
32
hrs.
15
min.
15
min.
10
hrs.
21
hrs.
25
hrs.
50°F
60
min.
100
min.
28
hrs.
64
hrs.
72
hrs.
20
min.
25
min.
10
hrs.
20
hrs.
26
hrs.
15
min.
8
min.
5
hrs.
10
hrs.
17
hrs.
70°F
50
min.
75
min.
16
hrs.
30
hrs.
36
hrs.
15
min.
20
min.
4
hrs.
8
hrs.
12
hrs.
90°F
25
min.
50
min.
7
hrs.
12
hrs.
16
hrs.
---
5.
6.
7.
-----
The two ingredients should be mixed in the
prescribed ratios, using a low speed (<750rpm)
jiffy-style mixer. Mix Part A first in its own bucket
for about 30 seconds, then add Part B hardener
and mix for at least 30-60 seconds at low speeds
until uniform in color.
Immediately after mixing, pour the contents onto
the floor in a ribbon pattern, spread with a
notched rubber squeegee to the desired coverage
rate, e.g. 160SF/gal for 10 mils, then back-roll
with a quarter inch, adhesive type roller. Do not
over-roll as this can result in bubble formation.
While still wet, broadcast suitable grit into the
first coat. This may be back-rolled for obtaining a
more uniform texture. Allow to dry tack free.
Apply second coat to lock in aggregate and obtain
a minimum 20 mil thickness. Note: If only one
thick coat can be applied (>15mils), a pin roller
should be used to facilitate air release.
---
Note:
Failure to follow the above instructions, unless
expressly authorized by a Milamar Technical Service
Representative, will void our material warranty.
---
Precautions
---
---
1.
---
---
---
---
2.
3.
---
---
4.
---
---
5.
Recoat windows without sanding: Regular Cure
at 70°F: 36 hours; Fast Cure at 70°F: 12 hours; XFC
at 50°F: 18 hours.
Do not use Guard Coating below 50°F.
Do not use Guard Coating FC below 40°F or above
70°F.
Do not use Guard Coating XFC below 32°F or
above 50°F.
If applied below 50°F, Guard Coating FC and XFC
will water stain.
Installation
Product Specifications
Please refer to our application instruction sheet for more
detailed information.
The specified area shall receive an application of ICO Guard
Coating™ as manufactured by Milamar Coatings L.L.C., of
Oklahoma City, Oklahoma. The system shall be installed by
precisely following the manufacturer’s published
recommendations pertaining to surface preparation,
mixing and application. The material shall be a low odor,
solvent-free, 100% solids, high gloss flexible epoxy system
with good resilience to resist thermal and mechanical
shock. The system must adhere to damp as well as dry
concrete, wood, metal, tile, terrazzo, and sound existing
epoxy and urethane coatings. It shall have an elongation of
9% in the unfilled form when tested using ASTM D-638. The
film hardness shall be a Shore D of 80. The system shall be
unaffected by oils, greases and resist such chemicals as 36%
hydrochloric acid, 20% nitric acid, 50% sulfuric acid and 50%
sodium hydroxide.
1.
2.
3.
New concrete should be allowed to cure for 28
days; however, if shorter times are necessary, a
plastic sheet and calcium chloride test should be
taken. Call ICO Tech Service when results are
obtained.
Floor must be abraded to a minimum 60 to 80 grit
size depending on coating thickness and be free
of all oils, grease and other impurities. When
recoating over old surfaces, all gloss should be
removed
Primer is necessary; however, if floor is
particularly porous, our low viscosity primer, ICO
Primer LV or LVFC can be applied and allowed to
dry tack free before applying first coat.
The data statements and recommendations set forth in this
product information sheet are based on testing, research
and other development work which has been carefully
conducted by us, and we believe such data. Statements and
recommendations will serve as reliable guidelines.
However, this product is subject to numerable uses under
varying conditions over which we have no control, and
accordingly we do NOT warrant that this product is suitable
for any particular use. Users are advised to test the product
in advance to make certain it is suitable for their particular
production conditions and particular use or uses.
LIMITED WARRANTY
Milamar Coatings products are manufactured to be free of
defects in material and workmanship in meeting the
properties specified on its individual Product Data Sheets.
Users and installers of Milamar Coatings products are solely
responsible for determining the suitability of the products
for specific product applications. Milamar Coatings makes
no Warranty or Guarantee, express or implied, including
warranties of fitness, design compatibility or
merchantability, for any particular use and shall have no
responsibility or liability, including direct, indirect or
consequential damages, due to injury, delay or third party
claims for installation or repair. Likewise, Milamar Coatings
assumes no liability of any nature for products that are
adjusted in the field or that do not utilize all specified
Milamar Coatings components. Should any Milamar
Coatings product be proved to be defective within one year
from the date of shipment, Milamar Coatings will, at its sole
discretion, either replace the material; issue a credit to the
customer’s account; or provide a cash refund for the initial,
paid purchase price of the material. Potential claims
regarding product quality must be received in writing by
Milamar Coatings within 30 days of the discovery of such
potential defect. This Warranty is exclusive of all other
warranties, expressed or implied, and may only be adjusted
in writing, signed by an officer of Milamar Coatings, L.L.C.
Milamar Coatings, L.L.C.
311 NW 122nd St., Suite 100
Oklahoma City, OK 73114
800.459.7659
www.milamar.com
ICO Guard
Coating GF
Product Data Sheet
Product Description
ICO Guard Coating GF is a 100% solids, two-part epoxy
coating reinforced with glass flakes for enhanced
permeability resistance.
It has several significant
advantages over conventional vinyl ester tank linings,
including no need for special ventilation in confined spaces,
superior damp adhesion, and ability to be applied in greater
thicknesses per coat on vertical and overhead surfaces. ICO
Guard Coating GF has excellent adhesion to damp as well as
dry properly prepared concrete and metal surfaces.
ICO Guard Coating GF is available in all of our standard
colors in 4 gallon pre-measured kits. It can be applied by
brush, roller or spray up to 20 mils per coat at 70°F without
sagging. Two 20 mil coats are recommended for optimal
permeation resistance in immersion. No primer is required
except when coating over rusted metal.
Product Application
ICO Guard Coating GF is designed to protect metal and
cementitous substrates subjected to long term immersion
conditions where chemical attack can be expected. Typical
applications would be clarifiers, settling ponds and filtration
tanks found in industrial and municipal waste water
treatment facilities, as well as sewer lines, manholes,
connector boxes and metal tank linings where chemical
concentrations are compatible with our “Guard” product
line (see Milamar Chemical Resistance Chart). Maximum
reagent temperatures should not exceed 120°F.
Badly pitted or spalled concrete should first be prefilled
with our ICO Gel epoxy patch material prior to coating. For
pitted concrete surfaces with exposed aggregate, our 1/8”
trowel applied ICO Guard Liner would be the choice,
especially in trenches, sumps and pits
Chemical Resistance
ICO Guard Coating GF is appropriate for immersion use
when rated “I” in our Chemical Resistance Chart (see “ICO
Guard” heading).
Physical Properties
Tensile
4925
Strength
psi
(ASTM D-638):
Tensile
Elongation (D9%
638):
Hardness,
Shore D (D2240):
80
60° Gloss
100
Gardner Impact
Strength:
80 in
lbs.
Bond Strength
to Quarry Tile:
Vapor
Transmission
Rate (E-96):
>1000
psi
0.02
perms
Physical Characteristics
Mixing Ratios
By Volume
Part A : Part B
1.6:1
Density, lbs. /gal.
Part A:
11.0
Part B:
8.6
A&B Mixed:
10
Curing Times
Pot Life:
Work Time:
Tack Free:
Hard:
By Weight
2:1
Viscosity @ 77°F, cps
Part A:
35,000
Part B:
3000
A&B Mixed:
6000
50°F
50 min.
70 min.
28 hrs.
64 hrs.
70°F
40 min.
50 min.
16 hrs.
30 hrs.
90°F
20 min.
25 min.
7 hrs.
12 hrs.
Maximum chemical and physical properties achieved after
7 days at 70°F
Color Availability
Standard colors: white, gray, dark gray, beige, yellow, red,
green, blue, brown, black.
Packaging and Coverage Rates
4 gallon kit:
320 SF
Shelf Life 1 year at 77F in unopened containers.
Installation
Please refer to our Application Specs for detailed
instructions. Particular care must be taken to follow those
instructions precisely to assure proper installation.
1. New concrete should be allowed to cure for 28 days. If
not possible, then test with plastic sheet for rate of vapor
transmission to surface and consult ICO Tech Service for
recommendations.
2. Old concrete should be sand blasted to remove all old
coating, down to a clean, abraded (40 to 50 grit minimum)
surface.
3. Metal surfaces must be blasted to achieve a white metal
finish (SSPC-SP-5) with a 2 to 3 mil angular profile. Coating
should be applied within 8 hours of completion of prep.
4. No primer is necessary.
5. On worn, spalled concrete, pre-fill with ICO Gel epoxy
patch and allow to dry tack free.
6. Mix Part A contents first for at least 30 seconds to ensure
uniformity, then add Part B and mix with a slow speed (<
750rpm) jiffy style mixer, or until uniform in color. To
prolong pot life, pour out into rolling pans.
7. Apply by brush or ¼” adhesive roller at a coverage rate of
80SF/gal at 70°F (=20 mils DFT). Allow to dry tack free.
8. Material may also be applied with an airless spray
apparatus with a 40:1 pump ratio, 3500psi fluid pressure,
0.021” fluid tip and a minimum ¾” I.D. air input line.
9. Apply a second coat at the same coverage rate as the
first. Note that if curing time for first coat exceeds 30 hours
at 70°F, it must be sanded prior to applying second coat.
Note: Failure to follow the above instructions, unless
expressly authorized by a Milamar Technical Service
Representative, will void our material warranty.
Precautions
1.
2.
3.
Recoat windows without sanding: regular cure at
70°F: 30 hours.
Do not use Guard Coating GF below 50°F.
Mix Part A thoroughly to distribute flakes
uniformly.
Product Specification
The specified area shall receive an application of ICO Guard
Coating GF as manufactured by Milamar Coatings LLC. of
Oklahoma City, Oklahoma. The system shall be installed by
precisely following the manufacturer’s published
recommendations pertaining to surface preparation,
mixing and application. The material shall be a low odor,
solvent-free, 100% solids, glass flake-filled epoxy coating
with good resilience to resist thermal and mechanical
shock. The system must adhere to damp as well as dry
concrete, wood, metal, tile, terrazzo, and sound existing
epoxy and urethane coatings. It shall have a maximum
permeability rating of 0.2 perms as tested by ASTM E-96.
The film hardness shall be a D of 80. The system shall be
unaffected by oils, greases and resist such chemicals as 36%
hydrochloric acid, 30Shore % nitric acid, 50% sulfuric acid
and 50% sodium hydroxide.
The data statements and recommendations set forth in this
product information sheet are based on testing, research
and other development work which has been carefully
conducted by us, and we believe such data. Statements and
recommendations will serve as reliable guidelines.
However, this product is subject to numerable uses under
varying conditions over which we have no control, and
accordingly we do NOT warrant that this product is suitable
for any particular use. Users are advised to test the product
in advance to make certain it is suitable for their particular
production conditions and particular use or uses.
LIMITED WARRANTY
Milamar Coatings products are manufactured to be free of
defects in material and workmanship in meeting the
properties specified on its individual Product Data Sheets.
Users and installers of Milamar Coatings products are solely
responsible for determining the suitability of the products
for specific product applications. Milamar Coatings makes
no Warranty or Guarantee, express or implied, including
warranties of fitness, design compatibility or
merchantability, for any particular use and shall have no
responsibility or liability, including direct, indirect or
consequential damages, due to injury, delay or third party
claims for installation or repair. Likewise, Milamar Coatings
assumes no liability of any nature for products that are
adjusted in the field or that do not utilize all specified
Milamar Coatings components. Should any Milamar
Coatings product be proved to be defective within one year
from the date of shipment, Milamar Coatings will, at its sole
discretion, either replace the material; issue a credit to the
customer’s account; or provide a cash refund for the initial,
paid purchase price of the material. Potential claims
regarding product quality must be received in writing by
Milamar Coatings within 30 days of the discovery of such
potential defect. This Warranty is exclusive of all other
warranties, expressed or implied, and may only be adjusted
in writing, signed by an officer of Milamar Coatings, L.L.C.
Milamar Coatings, L.L.C.
311 NW 122nd St., Suite 100
Oklahoma City, OK 73114
800.459.7659
www.milamar.com
ICO Lastic / ICO
Lastic Gun Grade
Product Data Sheet
Product Description
ICO-Lastic is a two part, 100% solids epoxy-modified
urethane. With elongation of 140%, it combines the
elastomeric properties of a urethane with the excellent dry
and damp adhesion of an epoxy. Normally applied by roller
or squeegee down to a minimum thickness of 20 mils, ICOLastic offers an impermeable moisture barrier against
standing water. Applied by trowel in a “gun grade” version,
ICO Lastic Gun Grade, it can also be used for interior
expansion joints where moderate movement is expected.
At minimum 60 mil thick applications, ICO-Lastic offers
excellent crack bridging characteristics for inside or outside
concrete structures. It will withstand light to moderate tow
motor and automobile traffic.
Product Application
ICO-Lastic is used in food and beverage plants, where it’s no
odor characteristics are desirable, as a waterproof
membrane underneath acid brick or tile floors. Applied at
approximately 60mils, it provides a good secondary
containment barrier against some acids, caustics and fuel
oils. For more highly corrosive areas, where crack bridging
is required, ICO-Lastic is applied beneath one of our quarter
inch higher chemical resistant epoxy overlayments. ICOLastic also acts as a complete waterproofing barrier for
parking garages, balconies, walkways and roof decks (use
ICO Ure Guard 80 or 100 for better UV resistance).
ICO-Lastic Gun Grade offers a resilient (100% tensile
elongation) yet tough caulking material that will hold up to
normal fork lift traffic in expansion joints where moderate
movement is expected. For old concrete floors, where little
movement is expected, use of our 100%solids epoxy, ICO
Caulk, is preferred.
Chemical Resistance
ICO-Lastic can withstand up to 72 hours immersion in the
following chemicals.
Hydrogen Sulfide
Urine
Vinegar
Kerosene
Jet Fuel
Water,
Deionized
Physical Properties
(Unless otherwise designated, for ICO Lastic)
Tensile
Tensile Strength 1480
Elongation, Gun
(ASTM C-638):
psi
Grade:
Rebound
Hardness, Shore
30%
Resiliency, %:
A, Gun Grade:
Tensile
Bond Strength To
Elongation (D140%
Concrete:
638):
Hardness, Shore
Water
80
A:
Absorption:
Physical Characteristics
(Unless otherwise designated, for ICO-Lastic)
Density lbs./gal.
Part A:
9.34
Part B:
7.91
A&B Mixed:
9.20
Viscosity @ 77°F, cps
Part A:
15,200
Part B:
380
A&B Mixed:
10,880
Mixing Ratios:
Part A : Part B
Part A : Part B, GG
Curing Times @:
Pot Life:
Work Time:
Hard Foot Traffic:
80
400 psi
(Concrete
Failed)
2% after 7
days
Gun Grade
10.1
7.91
9.93
Gun Grade
120,800
380
60,000
By Volume
8.09:1
9.02:1
40°F
30 min.
45 min.
72 hrs.
100%
50°F
25 min.
30 min.
28 hrs.
By Weight
9.55:1
11.52:1
70°F
20 min.
20 min.
15 hrs.
Maximum Hardness achieved after 7 days @77F.
Ammonium
Nitrate Diesel
Fuel
Beer
Palm Oil
Carbonated
Beverages
Sodium
Hypochlorite,
10%
Sulfuric Acid, 20%
Lactic Acid, 20%
Sugars
Color Availability
All of our standard colors
Mineral Spirits
Boric Acid
Sodium
Hydroxide, 50%
Bleach
Salt Brine
Shelf Life
1 year at 77F in unopened containers
Chlorine Water
Citric Acid
Ethylene Glycol
Ferric Chloride
Tartaric Acid
Packaging and Coverage Rates
ICO-Lastic (for 20 mils)
4 gallon kit : 320 SF
25 gallon kit : 2000 SF
ICO-Lastic Gun Grade
1 gallon kit : 75 LF, 1/2” x 1/2”
90°F
8 min.
10 min.
6-8 hrs.
Installation
Please refer to our Application Specs for detailed
instructions. Particular care must be taken to follow those
instructions precisely to assure proper installation.
1. New concrete should be allowed to cure a minimum of
28 days and/or be checked with a rubber mat or plastic
sheet to insure adequate curing time.
2. All surfaces to be covered should be power washed, shot
blasted, acid etched, scarified or sanded to present a clean,
sound substrate to which to bond to. The prepared surface
should have a ph. of 7.
3. ICO Lastic is a self-priming material; however application
of a single coat of ICO Primer LV over porous substrates is
recommended to help prevent out gassing. Apply at a
coverage of 180-200 SF/gallon and allow to dry.
4. Mix Part A and Part B components at slow speeds (< 700
rpm) with a Jiffy style mixer for at least two minutes, until
uniform in color. See Tech Bulletin 117 for details.
5. Pour the mixture onto the substrate and spread with a
squeegee, trowel or roller at a coverage rate of no greater
than 80 SF/gallon (for 20 mils). Spike roll with a porcupine
roller to help release air.
6. If an anti-slip surface is required, broadcast in aggregate.
7. No top coating is required; however, if exposure to UV
light, application of one of our urethane coatings is
recommended.
Failure to follow the above instructions, unless expressly
authorized by a Milamar Technical Service Representative,
will void our material warranty.
Precautions
1. For crack bridging (up to 1/8” wide), apply ICO Lastic at
least 60 mils thick.
2. ICO Lastic Gun Grade, with 100% elongation, best suited
for inside expansion joints with only moderate
temperature swings.
3. Do not apply below 40°F.
Product Specification
The specified area shall receive an application of ICO-Lastic
as manufactured by Milamar Coatings LLC. of Oklahoma
City, Oklahoma. The material shall be installed by precisely
following the manufacturer’s published recommendations
pertaining to surface preparation, mixing, and application.
The material shall be a low odor, solvent-free, 100% solids
epoxy-modified polyurethane with no toxic byproducts.
The material shall be available in a variety of acceptable
colors. It shall have an elongation of at least 140% at 70F
when tested using ASTM D638. Material shall also have a
tensile strength of at least 1400 psi and bond strength
greater than the cohesive strength of concrete. The system
shall be unaffected by most caustics, oils, greases and many
low strength acids.
The data statements and recommendations set forth in this
product information sheet are based on testing, research
and other development work which has been carefully
conducted by us, and we believe such data. Statements and
recommendations will serve as reliable guidelines.
However, this product is subject to numerable uses under
varying conditions over which we have no control, and
accordingly we do NOT warrant that this product is suitable
for any particular use. Users are advised to test the product
in advance to make certain it is suitable for their particular
production conditions and particular use or uses.
LIMITED WARRANTY
Milamar Coatings products are manufactured to be free of
defects in material and workmanship in meeting the
properties specified on its individual Product Data Sheets.
Users and installers of Milamar Coatings products are solely
responsible for determining the suitability of the products
for specific product applications. Milamar Coatings makes
no Warranty or Guarantee, express or implied, including
warranties of fitness, design compatibility or
merchantability, for any particular use and shall have no
responsibility or liability, including direct, indirect or
consequential damages, due to injury, delay or third party
claims for installation or repair. Likewise, Milamar Coatings
assumes no liability of any nature for products that are
adjusted in the field or that do not utilize all specified
Milamar Coatings components. Should any Milamar
Coatings product be proved to be defective within one year
from the date of shipment, Milamar Coatings will, at its sole
discretion, either replace the material; issue a credit to the
customer’s account; or provide a cash refund for the initial,
paid purchase price of the material. Potential claims
regarding product quality must be received in writing by
Milamar Coatings within 30 days of the discovery of such
potential defect. This Warranty is exclusive of all other
warranties, expressed or implied, and may only be adjusted
in writing, signed by an officer of Milamar Coatings, L.L.C.
Milamar Coatings, L.L.C.
nd
311 NW 122 St, Suite #100
Oklahoma City, OK 73114
800.459.7659
www.milamar.com
ICO Primer LV
Product Data Sheet
Product Description
ICO-Primer LV is a low viscosity, two part, 100% solids
epoxy primer. It is virtually odorless and non-toxic. ICO
Primer LV has excellent damp, as well as dry adhesion to
concrete, masonry surfaces, wood and gyp board. (For
priming metal, we recommend our Rust Guard Coating).
With a very low viscosity of 250 centipoise, it readily
penetrates porous substrates to provide an excellent
mechanical bond. Such a highly penetrating primer has also
been found effective in sealing the concrete to help prevent
outgassing. Where faster curing times are required, specify
ICO Primer LV FC. For application between 32°F and 50°F,
Curing Times@:
ICO
Primer LV
ICO
Primer LV
FC
our ICO Primer XFC material should be used. For vertical
surfaces, our ICO Primer XT is preferred.
Product Application
ICO-Primer LV must be applied before using our ICO Patch
(at a 10:1 mix) and our ICO Coat 81 trowelled material (at
an 8:1 aggregate : liquid mix). The primer should be allowed
to tack up prior to application of the top coat. For all our
other self-priming floor toppings and coatings, our primers
should be allowed to dry tack free to maximize its
effectiveness in sealing the concrete to reduce any possible
outgassing. ICO Primer LV can also be used as a penetrating
concrete sealer to prevent dusting and moisture
penetration.
Physical Characteristics
Density, lbs./gal.
ICO Primer LV
ICO Primer LV FC
Viscosity@77F, cps
ICO Primer LV
ICO Primer LV FC
Pt. A
9.52
9.52
Pt. A
476
476
Pt. B A&B Mixed
8.01
9.22
8.22
9.32
Pt. B A&B Mixed
60
250
60
250
Mixing Ratios (Part A: Part B)
By Vol. By Wt.
ICO Primer LV
3.4444:1 4.10:1
ICO Primer LV FC 4.63:1
5.37:1
ICO Primer FC
2.74:1
3.08:1
ICO Primer XFC
2.51:1
2.67:1
ICO Primer XT
3.49:1
4.19:1
Packaging and Coverage Rates
ICO Primer LV & LV FC
ICO Primer FC, XFC & XT
4 Gallon Kit:
1000 SF
800 SF
20 Gallon Kit:
5000 SF
4000 SF
100 Gallon Drum Kit: 25,000 SF
20,000 SF
40°F
50°F
70°F
Pot Life:
---
35 min.
25 min.
Work Time:
---
85 min.
85 min.
Tack Free:
Set Hard:
-----
40 hrs.
72 hrs.
10 hrs.
18 hrs.
Pot Life:
---
10 min.
9 min.
Work Time:
---
30 min.
30 min.
----25
min.
28
min.
16
hrs.
36
hrs.
20
min.
22
min.
16
hrs.
36
hrs.
18 hrs.
30 hrs.
5 hrs.
9 hrs.
90°F
15
min.
50
min.
5 hrs.
9 hrs.
9
min.
10
min.
2 hrs.
4 hrs.
20 min.
17 min.
---
25 min.
25 min.
---
8 hrs.
2 hrs.
---
24 hrs.
8 hrs.
---
15 min.
---
---
18 min.
---
---
10 hrs.
---
---
25 hrs.
---
---
Tack Free:
Set Hard:
Pot Life:
ICO
Primer FC
Work Time:
Tack Free:
Set Hard:
Pot Life:
ICO
Primer
XFC
Work Time:
Tack Free:
Set Hard:
ICO
Primer XT
Pot Life:
---
35 min.
25 min.
Work Time:
---
85 min.
85 min.
Tack Free:
Set Hard:
-----
40 hrs.
72 hrs.
10 hrs.
18 hrs.
Maximum Hardness achieved after 7 days @77F.
Installation
Please refer to our Application Specs for detailed
instructions. Particular care must be taken to follow those
instructions precisely to assure proper installation.
1. New concrete should be allowed to cure a minimum of
28 days and be checked with a rubber mat or plastic sheet
to insure adequate curing time. If this is not possible,
contact ICO Technical Service for further information.
2. All surfaces to be covered should be power washed, shot
blasted, acid etched, scarified or sanded to present a clean,
15
min.
50
min.
5 hrs.
9 hrs.
sound substrate to which to bond to. The prepared surface
should have a ph of 7.
3. Part A and B should be mixed in the prescribed ratio,
using a low speed jiffy-style mixer (maximum 750 rpm), for
at least 60 seconds.
4. ICO Primer LV is a 100% solids epoxy and no solvents are
necessary.
5. Apply the mixed material with a fine nap adhesive roller,
squeegee or brush. Apply at approximately 200-250 SF per
gallon, depending on surface porosity.
6. Reprime any dry appearing areas.
Failure to follow the above instructions, unless expressly
authorized by a Milamar Technical Service Representative,
will void our material warranty.
Precautions
1. Primer LVFC very fast reacting; pour out of bucket
immediately after mixing and spread with squeegee,
especially at temps greater than 70°F
2. Only Primer FC and XFC can be applied below 50°F. Do
not apply Primer XFC above 50°F
3. Recoat windows at 70°: Primer LV – 18 hours; LVFC – 10
hours; FC – 8 hours; XT – 18 hours, for expanding recoat
window, broadcast in aggregate into primer.
4. Never apply Primer LV or LV FC more than 15 mils
(100SF/gallon) per pass as it will not cure hard in greater
thicknesses.
Product Specification
The specified area shall receive an application of ICOPrimer LV as manufactured by Milamar Coatings LLC of
Oklahoma City, Oklahoma. The system shall be installed by
precisely following the manufacturers published
recommendations pertaining to surface preparation,
mixing, and application. The material shall be a low odor,
solvent free, 100% solids epoxy primer with excellent
adhesion to damp as well as dry concrete, metal and wood.
It should be able to adhere to brick and tile, exceeding 1000
psi on an Elcometer pull test.
The data statements and recommendations set forth in this
product information sheet are based on testing, research
and other development work which has been carefully
conducted by us, and we believe such data. Statements and
recommendations will serve as reliable guidelines.
However, this product is subject to numerable uses under
varying conditions over which we have no control, and
accordingly we do NOT warrant that this product is suitable
for any particular use. Users are advised to test the product
in advance to make certain it is suitable for their particular
production conditions and particular use or uses.
LIMITED WARRANTY
Milamar Coatings products are manufactured to be free of
defects in material and workmanship in meeting the
properties specified on its individual Product Data Sheets.
Users and installers of Milamar Coatings products are solely
responsible for determining the suitability of the products
for specific product applications. Milamar Coatings makes
no Warranty or Guarantee, express or implied, including
warranties of fitness, design compatibility or
merchantability, for any particular use and shall have no
responsibility or liability, including direct, indirect or
consequential damages, due to injury, delay or third party
claims for installation or repair. Likewise, Milamar Coatings
assumes no liability of any nature for products that are
adjusted in the field or that do not utilize all specified
Milamar Coatings components. Should any Milamar
Coatings product be proved to be defective within one year
from the date of shipment, Milamar Coatings will, at its sole
discretion, replace the material; issue a credit to the
customer’s account; or provide a cash refund for the initial,
paid purchase price of the material. Potential claims
regarding product quality must be received in writing by
Milamar Coatings within 30 days of the discovery of such
potential defect. This Warranty is exclusive of all other
warranties, expressed or implied, and may only be adjusted
in writing, signed by an officer of Milamar Coatings, L.L.C.
Milamar Coatings, L.L.C.
nd
311 NW 122 St, Suite #100
Oklahoma City, OK 73114
800.459.7659
www.milamar.com
YAKIMA CO JAIL ANNEX SHOWER RENOVATION
LEANNE SCHROYER
DLR GROUP
3/11/16
LIGHTING PRIOR
SUBSTITUTION PROCEDURES
PRODUCT REQUIREMENTS
016000
FMR-D-12-LD4-2LO-35-UNV-80-86-EDC1-CPHF-WL
800-942-0763
EATON LIGHTING
FAIL-SAFE
X
X
LEANNE SCHROYER
AMBIENT LIGHTING
2610 N VAN MARTER RD STE 3, SPOKANE VALLEY, WA 99206
509-922-5011
Project: YAKIMA CO JAIL ANNEX SHOWER RENOVATION
Contents - March 11, 2016
Type
Factory
H
Fail-Safe
Ambient Lighting
Description
FMR-D-12-LD4-2LO-35-UNV-80/60-EDC1-CPH
F-WL
2610 N Van Marter Road, Suite #3, Spokane Valley,WA 99206
p: 509.922.5011
f: 509.922.5017
Submitting Agency:
Description:
Project:
Notes:
FMR-D-12-LD4-2LO-35-UNV-80/60-EDC1-CPHFWL
YAKIMA CO JAIL ANNEX SHOWER RENOVATION
Type:
H
Fail-Safe
DESC RIPTION
The Fail-Safe FMR LED combines maximum security construction
features with energy saving technology. This recessed luminaire utilizes a
one-piece overlapping door frame, security lensing and tamper-resistant
fasteners to maximize impact-resistance and prevent contraband
concealment and unauthorized fixture penetration. ETL listed for damp
locations. The FMR LED is ideal for confinement/security applications.
Suitable for use in inmate cells, psychiatric wards, secure corridors and
general population areas.
Type
Catalog #
Project
Date
Comments
Prepared by
SPECIFICATIO N F EA T UR ES
Fa s te n e r s
D oo r
L ens
Stainless steel tamper-resistant
T20 TORX® screws with center pin
reject standard. Allen-head screws
with center pin reject optional
(SF3).
One-piece, CRS door frame (12,
14, 16 or 18 ga.) with die-formed
edges and tightly closed corners
increases rigidity. Aircraft cable
secures door to housing.
Choice of prismatic acrylic,
prismatic polycarbonate or
prismatic tempered glass on fixture
side, clear polycarbonate or clear
tempered glass on environmental
side.
Hou s in g
L ig ht Ma sk
Die-formed CRS body with
welded corners to form a onepiece housing which prevents
contraband concealment and
unauthorized fixture penetration.
Gasketing surrounds door frame
and prevents light leaks.
Fi n ish
High gloss, electrostatically
applied, white powder coat finish,
average minimum reflectance 92%.
Mou nti ng
Specify optional Yoke Mounting
Frame (YMF) or Swing-Out
Brackets (SWBR). Eye-bolt kit
for 4-point attachment to rigid
structure above, included standard.
L EDs
LEDs available in 3500k, 4000k,
5000k with CRI > 85. Projected
life is 50,000 hours at 70% lumen
maintenance.
L ens R ete ntion
Lens secured by thru-studs and
vertically adjustable internal CRS
hold-downs.
Mou nti ng Yo ke A sse m b ly
Hin ge
Fixture provided with (2) stainless
steel aircraft cables to attach door
to housing. Concealed piano hinge
optional.
16 ga., galvanized steel plaster
frame assembly (see Accessories).
Tra n sfo rmer/ Dr ive r
Electronic driver 120-277V. 0-10V
dimming standard.
FMR LED
LD4 LED
1' Width
2' Width
Confinement/Correctional
L abel s
ETL listed for damp locations. Wet
location under covered ceiling
optional.
SECURITY
Recessed Flange
NO MINA L INPUT W A TTS /DE L IVE RE D L UME NS (8 0 /8 6 SH I E L DI NG )
(80/86 shielding)
Fixture
Size
1' x 1'
1' x 2'
2' x 2'
# Modules
Level
Nominal
Input
Watts
Nominal
Delivered Lumens
(80/86 shielding)
Fixture
Size
# Modules
Level
Nominal
Input
Watts
Nominal
Delivered
Lumens
1
STD
12.3
800
1
LO
26.2
1808
2
STD
24.6
1600
1
STD
36.6
2488
1
LO
13.1
904
1
HI
47.2
3166
1
STD
18.3
1245
2
LO
52.4
3595
1
HI
23.6
1583
2
STD
73.2
4980
2
LO
26.2
1810
2
STD
36.6
2490
3
LO
39.3
2715
3
LO
78.6
5430
3
STD
54.9
4325
3
STD
109.8
7495
3
HI
70.8
4849
3
HI
141.8
9577
1' x 4'
2' x 4'
4
LO
52.4
3620
4
LO
104.8
7215
4
STD
73.2
4980
4
STD
146.4
9960
Nominal input wattage values include LED voltage, drive current, and typical driver efficiency. Refer to LM79 data/photometric files for exact
delivered lumen values and input wattage. Values in table are nominal values only.
TORX® is a registered trademark
of Camcar Division of Textron Inc.
PS519028EN
2015-05-21 10:47:14
Submitting Agency:
Description:
Project:
Notes:
FMR-D-12-LD4-2LO-35-UNV-80/60-EDC1-CPHFWL
YAKIMA CO JAIL ANNEX SHOWER RENOVATION
Type:
H
FMR LED
ORDE RING INF OR MA TIO N
SAMPLE NUMBER: FMR-X24-4-LD4-4STD-40-80/86-ED
FMR-S12-2-LD4-2LO-50-82/87-ED
Product
Family
Door
Width Length
FMR
No. of Illumination Color
Temp. Voltage Inner/Outer Lens
Level
LED
LED
/ 60
LD4
FMR
UNV=120-277V
S=12 ga.
X=14 ga.
D=16 ga.
N=18 ga.
Lens Type
Inner Layer (optional)
90=0.005 UV Absorbing
Overlay
Fixture Side
80=0.125 Prismatic Acrylic
81=0.156 Prismatic
Polycarbonate
82=0.187 Prismatic
Polycarbonate
93=0.156 Prismatic
Tempered Glass
24 =24" Wide
12 =12" Wide
1=1' Length (1' x 1' only)
2=2' Length
4=4' Length
LD4=LED
Electronic Driver 0-10V
Dimming
ED1C=1 Circuit
ED2C=2 Circuit
ED3C=3 Circuit
EL5W=5W
Emergency
Battery Pack 3, 4, 6
EL10W=10W
Emergency
Battery Pack 3, 4, 6
LLNL=Linear LED
Night Light,
Dimmable
GLR=Fuse and
Holder
14G=14 Guage
Housing
CPHF=Continuous
Piano Hinge,
Full Length
WL=Wet Location
Under
Covered Ceiling
Environmental Side
84=0.125 Clear Polycarbonate
85=0.187 Clear Polycarbonate
86=0.250 Clear Polycarbonate
87=0.375 Clear Polycarbonate
88=0.500 Clear Polycarbonate
94=0.187 Clear Tempered Glass
96=0.250 Clear Tempered Glass
97=0.375 Clear Tempered Glass
1=(1) LED Module
2=(2) LED Modules
3=(3) LED Modules (24" width only)
4=(4) LED Modules (24" width only)
STD=Standard
LO=Low
HI=High 5
35=3500K
40=4000K
50=5000K
Accessories
Options
Driver
9306=Allen-Head
Wrench
PF24-2FT=Plaster
Frame and Yoke
Assembly
PF24-4FT=Plaster
Frame and Yoke
Assembly
VRSD=T20 Center
Pin Tamperproof
TORX® - head
screwdriver
Mounting Options
SWBR=Swing-out
Brackets (4)
YMF=Yoke Mounting
Frame (2)
Stainless Steel Door
SSN=Natural Brushed
Finish
SSP=Polyester Powder
Coat Finish
Default fixture includes eye-bolt kit. Does not include SWBR or YMF. Mounting
hardware found in “Mounting Options”. Specify “SWBR” or “YMF” if necessary.
NOTES:
1 See Lens Guide for additional lens choices.
2 YMF consists of (2) C-channel frames, with (4) 3-1/2" bolts and nuts to attach YMF to fixture housing. YMF’s attach to rigid structure above.
3 EBP not available 1' x 1' or 1' x 2'. May be necessary to mount EBP on back of 2' x 2' fixture adding 2" to fixture depth.
4 EBP only available in “LO” or “STD” illumination levels.
5 24" width fixture, 4HI not available. 12" width fixture, 2HI not available.
6 Specify voltage.
Fasteners
SF3=Allen-Head (center
pin reject)
2 ' WID TH CROSS-SE C TIO N D I ME NSI ONS / SH OW N W ITH OP T I O NA L Y O KE M OU N T I NG F R A M E - YM F
YMF - Yoke
Mounting Frame
(optional)
2' x 2'
26-3/4" [680mm]
YMF - Yoke
Mounting Frame
(optional)
2' x 4'
26-3/4" [680mm]
3/4"
[19.05mm]
3/4"
[19.05mm]
4-1/4" [108mm]
5" [127mm]
21"
[533.4mm]
21"
[533.4mm]
24"
[610mm]
1/2"
[12.7mm]
24"
[610mm]
1/2"
[12.7mm]
2 ' WID TH TYPICA L M OU NT ING DE TA IL / S HOW N W IT H OP T I ON A L Y OK E M O U NT I N G F RA M E - Y M F
2' x 2'
2' x 4'
(2) 7/8"
Knockouts
14"
2"
YMF - Yoke
Mounting Frame
(optional)
9/16" x 1"
Hanger
Mounting Holes
YMF - Yoke
Mounting Frame
(optional)
(4) 7/8"
[22.23mm]
Knockouts
34" [864mm]
19"
[483mm]
14"
[355.6mm]
26-3/4"
[682mm]
17-3/4"
25"
2 ' WID TH OPTIONA L SW IN G- O UT BR AC KE T (S W BR )
2' x 2' / 2' x 4'
Eaton
1121 Highway 74 South
Peachtree City, GA 30269
P: 770-486-4800
www.eaton.com/lighting
(4) 7/8"
[22.23mm]
Knockouts
9/16" [14.3mm] x
4"
[101.6mm] 1" [25.4mm] Hanger
Mounting Holes
(2) 7/8"
Knockouts
Specifications and
dimensions subject to
change without notice.
2 ' W I D T H CE I LI N G C UT OU T D I M E NS I ON S
Ceiling
Cutout
Width
Length
2' x 2'
23-1/4"
24-1/4"
2' x 4'
23-1/4"
48-1/4"
PS519028EN
2015-05-21 10:47:14
Submitting Agency:
Description:
Project:
Notes:
Type:
FMR-D-12-LD4-2LO-35-UNV-80/60-EDC1-CPHFWL
H
YAKIMA CO JAIL ANNEX SHOWER RENOVATION
FMR LED
1 ' WIDTH CROSS-S E CT IO N DIM EN SION S / SH OW N W IT H O P T I O NA L Y O K E M OU N T I NG F RA M E - Y M F
YMF - Yoke
Mounting Frame
(optional)
1' x 4'
14-3/4"
[375mm]
YMF - Yoke
Mounting Frame
(optional)
1' x 2'
14-3/4"
[375mm]
3/4"
[19.05mm]
3/4"
[19.05mm]
4-3/4"
[120.65mm]
4-1/4"
[108mm]
8-7/8"
[225.4mm]
9"
[229mm]
12-1/8"
[308mm]
1/2"
[12.7mm]
12"
[305mm]
1/2"
[12.7mm]
YMF - Yoke
Mounting Frame
(optional)
1' x 1'
14-3/4"
[375mm
3/4"
[19.05mm]
4"
[101.6mm]
1/2"
[12.7mm]
9"
[229mm]
12"
[305mm]
1 ' WID TH TYPICA L M OU NT ING DE TA IL / S HOW N W IT H OP T I ON A L Y OK E M O U NT I N G F RA M E - Y M F
1' x 4'
1' x 1'
(2) 7/8"
[22.23mm]
Knockouts
40-1/4" [1022.4mm]
(2) 7/8"
[22.23mm]
Knockouts
9"
[229mm]
(2) 7/8"
[22.23mm]
Knockouts
12-3/4"
[324mm]
6-1/8"
[156mm]
YMF - Yoke
Mounting Frame
(optional)
1' x 2'
(2) 7/8"
[22.23mm]
Knockouts
4"
[101.6mm]
(6) 9/16" [14.3mm] x 1" [25.4mm] Hanger
Mounting Holes
YMF - Yoke
Mounting Frame
(optional)
12-3/4"
[324mm]
2"
[50.8mm]
22" [559mm]
(2) 7/8"
[22.23mm]
Knockouts
14-3/8"
[365mm]
(2) 7/8"
[22.23mm]
Knockouts
12-3/4"
[324mm]
(4) 9/16" [14.3mm]
x 1" [25.4mm] Hanger
Mounting Holes
6-1/8"
[156mm]
YMF - Yoke
Mounting Frame
(optional)
1 ' WID TH OPTIONA L SW IN G- O UT BR AC KE T (S W BR )
1' x 1', 1' x 2', 1' x 4'
Eaton
1121 Highway 74 South
Peachtree City, GA 30269
P: 770-486-4800
www.eaton.com/lighting
Specifications and
dimensions subject to
change without notice.
1 ' WI DT H CE I L I N G CU T OU T DI M E NS I ON S
Ceiling
Cutout
Width
Length
1' x 1'
10-1/2"
12-1/2"
1' x 2'
10-1/2"
24-1/2"
1' x 4'
10-1/2"
48-1/2"
PS519028EN
2015-05-21 10:47:14