selection
LED-control
2015
Table of contents
LED control gears
LCC8 Junior
V-36008235D
3
V-36009277D
4
LCC30
V-36030609
5
LCC60
V-36060579
5
LCC9sc
Synchronization and automatic cascading
LCC60MCM
Multi Control Module
V-36060579MCM
6
LCC60WCM
Wireless Control Module
V-36060579WCM
7
SSW60Q
softSwitcher 60Q
V-36060SSWQ
8-9
MCMP
Multi Control Module Push
V-40010DCMCMP
10
CMP
Control Module Push 0/1-10Vdc
V-40010DCP
10
®
LED control gears and big loads
11
EDL-system, Easy DALI LED-control
About the system
12
EDL-system components
12-13
motionDOT
V-40MODOT
13
pushDOT
V-40PUDOT
13
switchDOT
V-40SWDOT
13
sceneDOT
V-40SCDOT
13
busDOT
V-30125DALI
13
EDL-system installations
14
Project Cruse ship M/S Balmoral
14
LED dimmers
UD100
V-4010020IB
15
LD220
V-4022010IB
15
LD440
V-4044020IB
15
LightKey 2015
15
LED dimmers - Rotary type
PWM 360A
V-4036020PWM
16
KED10VDA
V-40010A20DC
16
VD200
V-4020020TRL
16
VD600
V-4060020L
16
Zero 35W
V-1503520RZ
17
Zero 70W
V-1507020Z
17
Du0 driving and dimming 12Vac LED
TM
2
Vadsbo LightTech
LED-control Selection
LED control gear LCC8 Junior
LCC8 Junior
LED control gear LCC8 Junior (V-36008235D)
A new addition in Vadsbo’s series of LED control gears.
LED control gear LCC8 Junior is a combined LED driver
and LED dimmer in one module for mounting in LED
fixtures or a wall box.
Dimmable with retractive switch or 1 -10Vdc control
signal. Designed for 350, 500 and 550mA constant
current LED, max load 8W.
The saving potential with Box installation
LED control gear
LCC8 Junior
V-36008235D
New and easier way to install
LED control gear LCC8 Junior is suitable for installation
into standard wall boxes (wall box installation) behind
the switch and simplifies installation and saves money
compared to central installation.
Central installation option means that the wiring is
done from groups of light fittings and switches to the
central control unit meaning long cables, more material
and more work.
Save money with Box installation
With wall box installation of LCC8 Junior you can save
a lot of money compared with central installation on
cost of materials and labour. Wall box installation means less cables and simpler electrical circuiting.
Scan for more
LCC8 information
Wiring Diagram
Power Range 1-8 W with 3 selectable DC currents
LED control gear LCC8 Junior with output from 1-8W
controls the most common constant current LEDs 350
mA along with 500 and 550 mA, selectable via DIP
switch. LCC8 Junior can not be connected in series.
+
+
-
1-10 Vdc
Sync without a sync cable
Up to 20 LCC8 Junior units can be controlled using the
same retractive switch. No extra synchronization cable
is required. The connection takes place on the primary
side by parallel switching the control signal that is
controlled by one or more reactive switches.
ON
ON
2 1
2 1
LED
L
N S
+
-
-
1-10 Vdc
LED
L
N S
+
-
Ideal size for build-into LED luminaires
LED control gear LCC8 Junior combines driver and
dimmer in one extremely small unit with diameter 54
mm and height 22 mm. Its wall box shape and small
size is a big advantage in installation. LED control gear
LCC8 Junior is ideally designed for mounting into LED
fixtures where the space for LED-driver and dimmer is
very limited.
L N
220-240 Vac
3
Vadsbo LightTech
LED-control Selection
LED control gear LCC9sc
LCC9sc
LED control gear LCC9sc - now with synchronization and automatic cascading
LED control gear LCC9 which is a patent-pending LED
driver and dimmer for LED fixture or wall box has now
been equipped with features for synchronization and
cascading under the name LCC9sc.
The new LED control gear LCC9sc is equipped with
new features to sync without a sync cable and automatic cascading. LCC9sc drives up to 540W LED and
controls with one retractive switch.
Easy to install with wallbox installation
LED control gear LCC9sc is suitable for installation into
a standard wall box (box installation) behind the switch
and simplifies the installation and saves money compared with central installation.
Central installation option means that the wiring is
done from light fittings and switches to the central
control unit meaning long cables, more equipment and
more work.
LED control gear
LCC9sc
V-36009277D
Larger power range by automatic cascade connection
Cascading means series connecting 2 or more units of
LCC9sc to dim loads with higher power requirements
than 9W.
A group of 2 units will drive and dim: 10-18W
A group of 3 units will drive and dim: 19-27W.
Multiple control options
LCC9 can be controlled by push (retractive switch) on
the primary side and by push and 1-10 Vdc signal on
the secondary side
Synchronization
Up to 20 groups (with up to 27W in each group) connected to LCC9sc units can be controlled using the
same retractive switch. No extra synchronization cable
is required.
New sync function on the primary side
You can synchronize up to 20 groups of LCC9sc on the
primary side by parallel connection of the switching
control signal which can be controlled by one or more
retractive switches.
New sync function on the secondary side
With the updated version 3 pcs can be cascaded and
synchronized automatically on the secondary side!
Save time and money with box installation
You can save a lot of money with box installation of
LCC9sc compared with central installation in costs for
materials and labor. Wall box installation means less
cables and simpler electrical circuit.
Up to 540W can be controlled by one swich
Scan for more
LCC9sc information
Wide current and voltage range with 7 selectable
DC currents and voltages
LED control gear LCC9sc covers all commonly occurring
currents and voltages such as 350, 500, 700 mA and
6, 9 ,12 and 24 Vdc selectable via DIP switch.
Ideal size for build-in in LED lights
LED control gear LCC9sc has a diameter of 56 mm and
a height of 23 mm. Its box shape and small size is a
big advantage in installation. LED control gear LCC9sc
is thus ideally designed for mounting into LED fixtures
where space for both driver and dimmer is very limited.
Economic comparison
between Box and
Central installation.
Save the Excel file
from the home page.
4
Vadsbo LightTech
LED-control Selection
LED control gearsLCC30 and LCC60
LCC30
LED control gear LCC30 (V-36030609)
LCC30 is a perfectly matched LED-driver and LED
dimmer in one unit for bigger LED-loads. It is able to
sync without a sync cable. With LCC30 you will be
able to drive up to 600W LED and dim the entire load
from one retractive switch. It will satisfy the highest
standards of simplicity, ease of use and thus customer
satisfaction.
LCC60
LED control gear LCC60 (V-36060579)
LCC60 is a perfectly matched LED-driver and LED
dimmer in one unit for bigger LED-loads. It is able to
sync without a sync cable. With LCC60 you will be
able to drive up to 1200W LED and dim the entire load
from one retractive switch. It will satisfy the highest
standards of simplicity, ease of use and thus customer
satisfaction.
Wider coverage of current and voltage range
LED control gear LCC30 covers all commonly occurring
currents and voltages selectable via DIP switches such
as 350, 500, 700 and 900 mA and 12, and 24 Vdc.
Wider coverage of current and voltage range
LED control gear LCC60 covers all commonly occurring
currents and voltages and is easily switchable between
350, 500, 700 and 900mA as well as 12 and 24Vdc.
Control options
LCC30 can be controlled by push (retractive switch)
on the primary side and by 1-10 Vdc signal on the
secondary side.
Control options
LCC60 can be controlled by push (retractive switch)
on the primary side and by 1-10 Vdc signal on the
secondary side.
Larger power range for constant current diodes
LED control gear LCC30 has larger power range compared to commonly used options on the market.
Larger power range of constant current diodes
LED controller LCC60 has larger power range, in
comparison with commonly used alternatives on the
market.
LCC30
Other options
Diodecurrent
Number of diodes
Number of diodes
350mA
500mA
700mA
900mA
1-16 pcs 1W LED
1-15 pcs 2W LED
1-12 pcs 3W LED
1-7 pcs 4W LED
1-12 pcs 1W LED
1-12 pcs 1W LED
1-9 pcs 1W LED
-
Synchronization without sync-cable
Up to 20 LCC30 can be controlled by a push button
that can be through-connected from driver to driver
and requires no external synchronization cable. It is
therefore possible to power up to 600W of LED.
Simultaneously controlled mixed loads
It is possible to combine constant current fixtures (CC),
constant voltage fixtures (CV) as well as popular LED
stripes on LCC30 and get an overall smooth dimming
by synchronizing the devices only through one push
button.
Easy to install in suspended ceiling
LCC30 is equipped with simple through connection
terminals for mains voltage 230 V as well as pushbutton control. The enclosure is designed with quicklocks on primary and secondary side and is equipped
with sturdy quick connection terminals. Installation in
suspended ceilings are made possible since LCC30 can
be entered through a normal 70 mm hole.
Sync without a sync cable up to 1200W
Up to 20 LCC60 can be controlled by a retractive
switch that can be forward connected from unit to unit
and requires no external synchronization cable. It is
therefore possible to control up to 600W and 1200W
LED with one retractive switch.
LED control gear
LCC60
V-36060579
Quick terminals
Snap-lids
Simultaneously mixed loads
With the aid of common cabling multiple units can
be synchronized. This means that you can set up one
device at 12Vdc, 350mA at another, a third at 700mA
and get them to run and dim synchronized with a
single switch! You can thus operate and dim LED strips
and LED fixtures simultaneously. Regardless of brand.
Unique memory function
The unique memory function means that you can turn
on or off the light with for example motion detectors,
twilight switches or timers. If the light is on in a specific
dimmed mode and incoming voltage to LCC60 is
broken there will be light in the last dimmed mode without any additional action by retractive switch when
the power returns.
This also means that, for example, when the fuse
blows at home, light will return directly when the
fuse has been restored. At the same time, you do not
have to worry that the light will be on when you come
home from vacation, for example, if in the meantime
there has been a brief power outage.
Individual outputs
LCC60 has two outputs that are individually adjustable.
You can run various LED types with the same control.
Insertion of LCC30
in a 70 mm hole
Scan for more
LCC30 and LCC60
information
LED control gear LCC30
V-36030609
5
Vadsbo LightTech
LED-control Selection
LED control gear LCC60MCM
LCC60MCM
Combined LED-driver and dimmer for DALI, DMX
and Push
LED control gear LCC60MCM (V-36060579MCM) is a
perfectly matched LED-driver and LED dimmer in one
unit for multiple control options and bigger LED-loads.
It is able to sync without a sync cable. With LCC60 you
will be able to drive up to 1200W LED and dim the
entire load from one retractive switch. It will satisfy the
highest standards of simplicity, ease of use and thus
customer satisfaction.
Multiple Control options
LCC60MCM can be controlled by push (retractive
switch) on the primary side and by 1-10 Vdc signal
on the secondary side as well as with DALI and DMX
signals.
DALI and DMX
LCC60MCM which is equipped with Multi control module MCM can be controlled by DALI and DMX.
The two outputs in the LCC60MCM can in a bus
system be controlled individually. Each outlet can dim
different types of LED. LCC60MCM gives a precise and
accurate dimming. You can via the bus system choose
exactly the dimmer level. In a bus system where twoway communication is supported it is possible to read
the status of for example, the current voltage and current, or error status such as short circuit or if no load is
connected.
Wider current and voltage range
LED control gear LCC60MCM covers all commonly
occurring currents and voltages and is easily switchable
between 350, 500, 700 and 900mA as well as 12 and
24Vdc.
Larger power of constant-current diodes
LED controller LCC60MCM has a larger power range,
in comparison with commonly used alternatives on the
market.
Sync without a sync cable up to 1200W
Up to 20 LCC60MCM units can be controlled by a
retractive switch that can be forward connected from
unit to unit and requires no external synchronization
cable. It is therefore possible to control up to 600W
and 1200W LED with one push button.
Simultaneously mixed loads
Common cabling allows multiple units to be synchronized. This means that you can set up one unit at 12Vdc,
another at 350mA and a third at 700mA and get them
to run and dim synchronized with a single push button! You can therefore run and dim LED strips and LED
luminaires simultaneously. Whatever the brands!
Unique memory function
The unique memory function
means that you can turn on/
off the light with for example
motion detectors, twilight
switches or timers. If the light
LCC60MCM
is on in a specific dimmed
V-36060579MCM
mode and incoming voltage
to LCC60MCM is broken
there will be light in the last dimmed mode without any additional action by
retractive switch when the power returns. This also means that, for example,
when the fuse blows at home, light will return directly when the fuse has been
restored. At the same time, you do not have to worry that the light will be on
when you come home from your vacation, if there in the meantime there has
been a brief power outage.
Individual outputs
LCC60MCM has two outputs that are individually addressable.
You can run various LED types with the same control gear.
Individually addressable outputs
In a DALI or DMX environment the two outputs of LCC60MCM can be
individually addressable by lighting group and by control unit.
Loop-in/Loop-out
Double terminals for quick and easy forwarding of
phase, neutral and guide wire. Up to 20 units with a
total power of 600W and 1200W can easily be controlled by a retractive switch. The units are connected
together with standard installation cable via the extra
control input. No special sync cable is required.
Scan for more
MCM information
Designation
LCC60MCM
Item number
V-36060579MCM
Constant current
(per output)
350mA (2-57V)
500mA (2-52V)
700mA (2-42V)
900mA (2-24V)
1-20W (1-16 psc LED Vf=3,6)
2-26W (1-14 psc LED Vf=3,6)
2-30W (1-12 psc LED Vf=3,6)
4-21W (1-6 psc LED Vf=3,6)
Constant voltage
(per output)
12Vdc
24Vdc
10,5W
21W
Number of outputs
2
Dimming
Pushbutton, 1-10V, DALI, DMX
Bus control MCM
Yes
Voltage primary
220-240Vdc
Ambient temp. max (Ta)
+50°C
Test temp. (Tc)
+75°C
Dimension (LxWxH)
220x62x34 mm
Degree of protection
IP20
6
Vadsbo LightTech
LED-control Selection
LED wireless control gear LCC60WCM - via Bluetooth
LCC60WCM
Combined LED-driver and dimmer using
wireless Bluetooth technology
Based on the popular LCC60 series LED-driver,
the WCM option (V-36060579WCM) adds wireless
control features based on the standard Bluetooth 4.0
protocol found in most modern smartphones and
tablets. With app support for the latest Android and
Apple’s iOS you can utilize any device to take full
control over all you luminaires.
Limitless range
By using MESH network technology you only need to
be within range (normally 100m) of any single control
gear to have control over all the luminaires in your
installation. Communication is automatically forwarded
between control gears to all other control gears within
its range. Because of the MESH technology you can
build large scale installations of thousands of lamps
and control them all from your smart phone.
Group and scene settings
Group any number of luminaires together in the app
and dim them simultaneously e.g. to dim a single
room or all spotlight luminaires in an installation.
Program pre-set scenes easily using the app’s intuitive
interface for fast setting of entire scenes throughout
your installation. Unlimited group and scene settings
provide uncompromising control over any installation
type.
LCC60WCM
V-36060579WCM
setup of any installation, from residential to large-scale commercial complexes.
With the LCC60WCM, any combination of CV and CC LED luminaires can be
mixed and controlled
from the same simple intuitive interface using your favorite device.
Controlling
Simply 1) take a picture of the different lighting groups in your installation,
your living room, conference room etc., 2) then combine it with the app to tie
the scenarios and grouping via photo. You can now take control of the lighting
groups by 3) touching individually on the screen the lighting/lamps you want to
control on/off or dim etc.
Retractive switches for local control
Connect a retractive switch to any control gear for
local control over a single luminaire or a group of
luminaires. The switch’s behavior can be customized
through the app to fit any type of installation scenario.
Access control
The LED control gears are paired to a master device
first time they are used. The master device can then
optionally share access permissions with any number of devices either using a password or leaving the
network open for access by any device. The internal
communication of the network is protected by a strong
asymmetrical-key encryption scheme.
Two channel control gear and Color-Shift
The LCC60’s versatile capability of two independent
LED-drive channels providing up to 30W of power each
can be utilized either to control two LED strings independently or a single string of color-shifting luminaires.
Combined with Vadsbo’s latest color-shifting luminaire
it provides seamless dimming between 2700K and
5700K maintaining a high quality light throughout the
entire spectrum. This enables dynamically shifting illumination settings for a wide variation of installations.
Flexibility
The LCC60’s ability to power a wide variety of LED
luminaires is now combined with the market’s most
versatile wireless control system provides the easiest
Designation
LCC60WCM
Item number
V-36060579WCM
Constant current
(per output)
350mA (2-57V)
500mA (2-52V)
700mA (2-42V)
900mA (2-24V)
1-20W (1-16 psc LED Vf=3,6)
2-26W (1-14 psc LED Vf=3,6)
2-30W (1-12 psc LED Vf=3,6)
4-21W (1-6 psc LED Vf=3,6)
Constant voltage
(per output)
12Vdc
24Vdc
10,5W
21W
Number of outputs
2
Dimming
Bluetooth, smartphone/tablet, retractive switch
Voltage primary
220-240Vdc
Ambient temp. max (Ta) +50°C
Test temp. (Tc)
+75°C
Dimension (LxWxH)
220x62x34 mm
Degree of protection
IP20
7
Vadsbo LightTech
LED-control Selection
The softSwitcher® technology
Dynamic interaction
A radically new technology for the design of LED-drivers where hardware is substituted with intelligent software algorithms controlling the switchingpatterns in
dynamic interaction with each other and the hardware
to control and optimize every aspect of a LED-driver or
control gear in relation to the load.
• Synchronized and dynamic adjustment of switching patterns in the driving circuitry results in overall reduction of unwanted EMI-disturbances.
• Less stress imposed on (less) hardware components
means >10 times longer life time of drivers.
• Energy conversion using less hardware means less
weight and smaller physical size of drivers.
• Intelligent software using microcontrollers means
limitless control options including 0-1/10 VDC,
DALI, DMX, pulse-switching, phase-angle control,
remote controls such as Wifi, Zigbee, Bluetooth etc.
• Enhanced utilization of electrical components
leading to higher efficiency (up to 90%) over the
entire output range means increased energy savings.
• Possible software features allowing remote
Internet-based control of the driving circuitry,
where the driving circuitry is given an IP-address for
updating of the software to meet new demands.
• Improved powerfactor up to 0,99 means less energy waste and improved environmental footprint.
• Possible seamless stepping between current control and pulse-width modulation means high color
accuracy of the LED.
• Intelligent patent pending coupling of converter
components means near zero stand-by energy
consumption in drivers.
• Scalable technology with customizable features
means short time to market for new projects.
Characteristics of the softSwitcher® technology
soft
itch
Sw er
T
NG
EN
T
A
P
PENDI
PENDI
Quick terminals and fast-lids ensure that installation is
quick. DIP switches allow the same LED control gear to
work on all commonly occurring LEDs where each output can be set individually. Primary side and secondary
side located on opposite sides separate low voltage
cables from from 230V cables in an installation.
LED control gear SSW60Q is a combination of LED
driver and LED dimmer executed in revolutionary digital
s
tfo
LED control gear SSW60Q
SSW60Q (V-36060SSWQ) is a combination of LEDdriver and LED dimmer in power of up to 60W on
two outputs. It is suitable for large indoor installations
such as office, retail, hotel or conference rooms. And
it is ideally suited for demanding lighting needs in all
locations.
ENT
GN
P AT
softSwitcher® SSW60Q - V-36060SSWQ
Sw er
technology. SSW60Q is the first product of the next
itch
generation LED control gears and is a wholly Swedishdeveloped product.
SSW60Q is designed to fit all LED loads on the market.
It is designed to be simple and quick to install.
This means that SSW60Q is optimal to use for everything from 12Vdc (60W) LED strips to fixtures operated
SSW60Q
on 2600mA.
Built with digital technology the size of the product is
optimized in a way that has never been possible before
in larger power classes. The only limitation contained in
SSW60Q is that the maximum load is 60W.
Generation-wise SSW60Q can be compared with the
step from the phone with dial to the smartphone.
8
Vadsbo LightTech
LED-control Selection
LED control gear softSwitcher® SSW60Q
1) Four different control options
• The retractive switch on the primary side,
per channel or joint (factory setting)
• Phase-dimming by trailing edge technology for
conventional dimming
• 0/1-10Vdc dimming
• External sensor connection for twilight switches
or time relays
2) DIP switches for
setting of LED type
Cover suited for
flexible hose
Standard cover
2) DIP Switch
Using the DIP switch allows you to set the type of
LED you want to dim. SSW60Q has two adjustable
outputs.
Selectable constant currents (mA)
150, 350, 700, 1050, 1400, 2600, etc.
Selectable constant voltage (Vdc)
6, 12, 24, 36, 48, etc.
3) Quick-terminal lid
3) Quick-terminals and lids
Quick-terminals and fast-lids with strain relief for easy
connection. SSW60Q is also provided with additional
cover for rapid engagement of for example 16 mm
hose.
4) Loop-in loop out connection
Dual terminals for quick and easy forwarding of
phase, neutral and guidewire. Up to 20 units for a
total of 1200W can easily be controlled by one push
button. The units are interconnected with standard
installation cable via the external control input. No
special sync cable required.
3) Quick terminals
4) Loop-in/Loop out
connections
5) SSW60Q is suitable for mounting
e.g. in suspended ceilings with 70 mm
downlight holes
5) Size
SSW60Q is easy to mount in the ceiling, due to its
small dimensions. Enters a 65-70mm downlight hole.
6) Memory Function
Designation
SSW60Q
Equipped with a memory function that also persists
after power failure. The latest dimmed level is
memorized even if the light was on or off.
Item number
V-36060SSWQ
Constant current
(per output)
350mA max 21W
500mA max 30W
700mA max 42W
7) Support of motion detector/ twilight relay/ timer
Constant voltage
(per output)
6Vdc 15W (paralleled outputs 2x15 = 30W)
12Vdc 30W (paralleled outputs 2x30 = 60W)
18Vdc 47W
24Vdc 60W
48Vdc 60W
Number of outputs
2
Dimming
1-10Vdc, phase angle-, push control, presence sensor
Voltage primary
230Vdc
The unique memory function enables switching on
and off of the light with eg motion detectors,
twilight relay or timer.
8) Screw Mounting
Holes for screw mounting to a wall or similar.
9) Features and protection
Ambient temp. max (Ta) +55°C
• Soft start, memory function
• Supports motion detectors, twilight relays and timers
• Overvoltage and overtemperature protection
• Short circuit protection with automatic reset
Test temp. (Tc)
+75°C
Dimension (LxWxH)
173x53x28 mm
Degree of protection
IP20
9
Vadsbo LightTech
900mA max 54W
1050mA max 60W
2600mA max 60W
LED-control Selection
Multi Control Module Push and Control Module Push 0/1-10Vdc
MCMP
Dimmable LED control gears and dimmable ECGs are
given advanced bus functions with MCMP.
Multi Control Module Push MCMP supplies all operating units for lighting that is 0-10 or 1-10Vdc control
with advanced bus functions.
Multi Control Module Push is a totally outstanding and
unique product. MCMP means in this context simplicity, ease of use and thus user satisfaction.
Controlling with DALI and DMX
All dimmable LED control gears for LED and dimmable
electronic ballasts with 0-10VDC or 1-10VDC can now
be controlled in a DALI or DMX environment, which
creates unique opportunities in combination with the
existing products on the market. MCMP currently supports DALI and DMX (and later KNX). MCMP regulates
common 0-10Vdc or 1-10Vdc dimmable devices such
as eg LED control gears and electronic ballasts.
With control input for push dimming
MCMP is equipped with a control input for push
dimming where you can connect a momentary push
button control.
Box shape
MCMP is made in box shape and can easily be placed
in a junction box behind a push button.
Low standby consumption
The relay is of bistable type, which means that the relay
only draws power when the switch changes position
(on / off). This means that it doesn’t develop any heat
in the relay function.
CMP 0/1-10Vdc
Push-button control module 0/1-10Vdc is a new push button dimmer which
aims to facilitate dimming of dimmable electronic ballast, LED control gears and
electronic transformers with 1-10Vdc input. The unit is made in box shape and
can easily be placed in a junction box behind a push button.
Dimming without problems
If you choose a 0/1-10Vdc push dimmer and a 0/1-10-Vdc LED control gear or
electronic ballast they will work together smoothly regardless of the brand.
Functions
The Control Module Push regulates common 0-10Vdc or 1-10Vdc dimmable
units such as LED control gears and electronic ballasts. The ability to break the
phase is there so you can switch on/off the units that are dimmable with 110Vdc.
The control module is equipped with “regulation of minimum dimming level”
and “regulation of minimum dimming speed”.
Push dimming
Push dimming has several advantages in terms of quick and easy dimming.
A short press for on/off, a long press for dimming up/down. Push dimming is
also convenient for the user who wants to control the light level from several different locations in the room - several buttons can control the same dimmer.
Large groups
You can easily provide a large group of eg LED control gears controlled by
1-10Vdc with quick and easy push dimming, which also can be dimmed from
multiple locations, unlike traditional 1-10Vdc dimmers in rotary dimmer execution.
Low stand-by consumption
The relay is of bistable type, which means that the relay only draws power when
the relay switches position (on/off). This means that it does not develop any heat
in the relay and the relay keeps its settings even after a power failure.
With memory function
MCMP retains its position even after a power failure.
Alternative possibilities
MCMP are also able to break the phase to turn off /
on the devices that are dimmable with 1-10Vdc. You
can then choose if the pushbutton for example should
guide 0/1-10Vdc regulation or any other device in the
system you want to control.
Scan for more
MCMP information
Scan for more
CMP information
Designation
MCMP
CMP
Item number
V-40010DCMCMP
V-40010DCP
Control inputs Controlled by one or more
push buttons
- DALI
- DMX512
Controlled by one or more
push buttons
Outputs
- 0-10V
- 1-10V with bistable relay for
switching function (Max 10A)
- Max 100mA control signal
- 0-10V
- 1-10V with bistable relay for
switching function (Max 10A)
- Max 100mA control signal
Function
- Adjustable between 0-10
or 1-10Vdc control
- Memory Function
- Adjustable between 0-10
or 1-10Vdc control
- Memory Function
10
Vadsbo LightTech
LED-control Selection
LED control gears and big loads
Sometimes you need to control bigger loads by a single
control than only one LED control gear can handle.
Depending on the type of LED control gear, there are
some different ways to solve this
Running multiple LED control gears with the same switch
Involves connecting the retractive switch to the control input of a LED control
gear and then connecting the control inputs of the LED control gears with standard installation cable. (See figure below.)
Cascading
2 pcs LED control gear LCC9 are serially connected on
the secondary side with the load. This enables that the
total power of LED in a single series loop to be doubled. For example, if a LED control gear handles max.
9W load (equivalent to for example to 7 pcs of 350mA
1.2W LED) two pieces can be serially connected giving
a total power of 18W, equivalent to eg 15 pcs of
350mA 1.2W LED in a loop. The control, whether it is
a momentary switch or a 1 -10Vdc control, is connected to the Master unit. The Master device is set to
the constant current the LED lights are rated for and
handles the constant current regulation of the light.
The slave unit is set at a constant voltage and helps as
a voltage boost circuit.
How to set up the LED control gear is shown in the
manual of the product.
The total power in a single series loop is limited by the maximum power of theLED control gear. The total power of a single control is limited by the number of
LED control gears that can be connected to a control and the maximum power
of the LED control gear. For example, if the LED control gear can handle max
30W it is 30W which is the limit of a loop of constant current LED. If you then
can connect 20 pieces of LED control gears to a retractive switch, the overall
power of a control- loop is 20 pcs x 30W giving a total of 600W.
Cascading only works in constant current dimming.
If the Master PWM regulates the current and you
then connect a slave who is set to constant voltage
out, there would be a conflict between them with an
undesirable result as a consequence. The reason that
you can not cascade connect 12 and 24Vdc constant
voltage is because 12 and 24Vdc is PWM controlled.
This means that you do not need any special sync cable
and regular installation cable can be used.
N
L
220-240 VAC
It is still perfectly possible to connect several retractive switches in parallel to
control the entire group of LED control gears from different places. After the
installation is completed, the system shall be synchronized the first time.
If you do not synchronize, there may be that some devices will shut down while
others switch on or dim uneven.
Synchronization is performed by the following procedure using the
retractive switch.
1. A long push (now, all LED control gear shall be lit).
2. A brief push (now, all LED control gear shall be off).
3. A long push until all LEDs are in their maximum position (the LED control gear
starts from min. position and goes up to max. if you hold the button down).
This means that you do not need any special sync cable and regular installation
cable can be used.
1 -10Vdc Control
Involves connecting a 1-10Vdc control module to the control input of the LED
control gear. All LED control gears will then get the same control signal from a
1-10Vdc control(dimmer).
The total power in a single series loop is limited by the maximum power of the
LED control gear. The total power of a single control is limited by the number of
LED control gears that can be connected to a control and the maximum power
of the LED control gear. For example, if the LED control gear can handle max
30W it is 30W which is the limit of a loop of constant current LED.
If you then can connect 20 pieces of LED control gears to a 1-10 Vdc dimmer,
the overall power of a control-loop is 20 pcs x 30W giving a total of 600W.
S LN
Slave
DIP
LED
– + – + Switch
S LN
Master
DIP
LED
– + – + Switch
Controlling multiple LED control gear with same button
Cascade connection
You can not connect multiple 1-10Vdc dimmers to the same control loop.
Thus you can not dim light from different points with this solution.
11
Vadsbo LightTech
LED-control Selection
EDL-system, Easy DALI LED-control
About the EDL-system
Vadsbo’s EDL system consists of a number of components which - in a simple and user-friendly way can be used to build a system with the basic lighting
control functions of DALI for LED lighting without
using a PC.
The main components of the system is LED control
gear LCC60MCM which drives and dims the most
common LED types on the market and Multi Control
module MCMP which controls and regulates all 0 or
1-10V controlled devices such as eg LED drivers.
LCC60MCM and MCMP can then together with the
other control modules in the EDL system be controled by DALI using momentary switches, prespresence
detec­tion devices or by retractive switches that can
easily be programmed for different scenarios.
The simplicity of the EDL-system
Simplicity is one of the most important aspects when
Vadsbo are developing new products. DALI actuators
tend normally to be set and configured via a computer
interface. This means that you, from the start, don’t
have control of the address of a specific actuator nor
where it is located.
Individually adressable outputs
Vadsbo has provided both LED control gear LCC60MCM
and MultiControlModule MCMP with manual adjustment of both the address and the group.
The setting is made via 3 pcs of knobs. 1 for the group
(0-15) and 2 pieces for the address (0-63).
In the same way the control modules are manually set.
This means that the EDL system can be easily installed
and manually adjusted without having to use a computer with advanced software.
The components of the EDL-system
- LCC9
- LCC30
- LCC60
- LCC60MCM
- MCMP
- CMP
V-36009277D
V-36030609
V-36060579
V-36060579MCM
V-40010DCMCMP
V-40010DCP
- motionDOT
- pushDOT
- switchDOT
- sceneDOT
- busDOT
- LD220
- LD440
V-40MODOT
V-40PUDOT
V-40SWDOT
V-40SCDOT
V-30125DALI
V-4022010IB
V-4044020IB
LCC60MCM (V-36060579MCM)
Each output will have its own address in a DALI or DMX system and can be
controlled individually. Address and group are easily set manually via three knobs
on the device.
LCC60MCM automatically detects if DALI signal or DMX signal is connected and
thus the same knob can be used for both DALI and DMX setting. If the DALI
signal is detected the knobs are used to set the DALI address and group, if DMX
signal is detected the same knobs are used to set the DMX address and group.
It goes without saying that the DALI address and group can be set by a computer
if desired.
MCMP Multi Control Module Push (V-40010DCMCMP)
MCMP is a box-actuator for DALI / DMX to 0-10 or 1-10V. Setting for 0-10 or
1-10V can be set directly on the device. You can also set the DALI commands
via a computer. Address and group is manually set via three knobs.
MCMP automatically detects if DALI signal or DMX signal is connected and thus
the same knob can be used for both DALI and DMX setting. If the DALI signal is
detected the knobs are used to set the DALI address and group, if DMX signal is
detected the same knobs are used to set the DMX address and group.
It goes without saying that the DALI address and group can be set by a computer
if desired.
This means that EDL is suitable for both the smaller and simpler system and the
bigger advanced system where you want to set and control everything via a
computer.
Individually addressable outputs
Scan to watch
the EDL-film
Precise control
You will also get a precise control directly over where
each address is placed in the facility when you set it
directly on the device and you do not have to identify
this in retrospect. Of course, you can also address and
do the grouping with for example software from a PC.
Projects
For detailed information of the EDL installations scan
the QR-codes below, visit www.vadsbo.net.
At page 12 you can find information about the
lighting project at the Cruise ship M/S Balmoral.
Project office Tesla
12
Lighting control restaurant da Vinci folder.
Vadsbo LightTech
Lighting control
villa Maxwell folder.
LED-control Selection
EDL-system components
motionDOT (V-40MODOT)
motionDOT is an interface between a regular presence
sensor or motion detector and DALI bus and can easily
be placed in an wall box.
The time delay is controlled by the motion detector. By
presence lighting is activated to 100% and by absence
lighting is set to a stand-by mode. Standby mode can
be adjusted from fully off to 75% brightness.
MotionDOT can be set to control a group of devices or
all devices on the DALI bus. Setting is done manually
with a knob.
LCC9sc
V-36009277D
see page 4
LCC30
V-36030609
see page 5
pushDOT (V-42PUDOT)
pushDOT is an interface between a normal retractive
switch and the DALI bus. 4 switches can be connected
and each button get the function to dim up/down, or
on/off. pushDOT can be set to control up to 4 individual units, groups or all units on the DALI bus.
Setting is done manually via a knob on the backside.
switchDOT (V-40SWDOT)
switchDOT enables dimming up and down and provides an interface between a standard retractive switch
and DALI bus and can easily be placed in an appliance
box. For example, a double switch can be connected to
the control module and a button dims up or switches
on while the second button down dims or turns off.
switchDOT can be set to control an individual unit,
group of units or all devices on the DALI bus. Setting is
done manually with a knob.
sceneDOT (V-40SCDOT)
sceneDOT enables the function to store and recall up
to four scenarios (home, away, cleaning, etc.).
4 buttons can be connected to the module, one for
each scenario. For achieving optimum results using a
4-channel low voltage switch is recommended.
Scenarios are easily stored in each scenario button, by
holding the button down for about 10 seconds.
sceneDOT can easily be placed in an appliance box.
To memorize eg ”All off” function on key 1 first all
lighting groups are manually switched off with each
unit’s individual control.
When all lights are switched off key 1 is pressed for 10
seconds. Confirmation of stored scenario is displayed
by all lights flashing.
Setting of - if only a specific group or if all devices on
the bus must store scenarios - is done manually with a
knob. You can also set which memory position
(of 16 possible) each button corresponds to.
LCC60
V-36060579
see page 5
LCC60MCM
V-36060579MCM
see page 6
MCMP
V-40010DCMCMP
see page 10
LD220
V-4022010IB
see page 15
motionDOT
pushDOT
V-40MODOT V-42PUDOT
sceneDOT
V-40SCDOT
LD440
V-4044020IB
see page 15
busDOT (V-30125DALI)
busDOT is a power supply for DALI bus and can deliver
up to 125mA. As an example, a control gear consumes
max 2mA and a control module max 6mA.
13
switchDOT
V-40SWDOT
Vadsbo LightTech
busDOT
V-30125DALI
LED-control Selection
EDL-system installations
Lighting control Cruise ship M/S Balmoral
Vadsbos EDL-system is since December 2014 installed
on board a restaurant on the Cruise ship M/S Balmoral
belonging to Fred Olsen Cruise Line.
The project was to update the lighting in the restaurant “Morning light Pub and Bar”.
The updated lighting is divided in two groups, the
restaurant and the bar, as shown below. It consists of
56 pcs of the LED control gear LCC60MCM and three
pieces of sceneDOT linked to two control panels.
By the system architecture and programming for such projects it is of great
importance to control individual addresses in different levels as well as fading in/
out and can therefore be performed with PC programming / tools.
The installed EDL-system is dimmer flicker-free 0-100% which the end customer
is very satisfied with.
The installation was done by Naesco, Miami, Florida - USA December 2014.
The LED lighting was delivered by Lyngsaa AS, Frederikshavn, Denmark.
The restaurant
DALI BUS 1 - Addresses 00-51, Group 0
Ceiling lighting
18 pcs LCC60MCM controls 108 pcs Lyngsaa LED/PAX400/4,2W/400lm/CRI>90
Decorative lighting 3 pcs LCC60MCM controls 16 pcs Lyngsaa LED/PAX400/4,2W/400lm/CRI>90
Wall lighting
2 pcs LCC60MCM controls 5 pcs Lyngsaa LED/rep-kit/3W/250lm/CRI>90
Emergency lighting 3 pcs LCC60MCM controls 10 pcs Lyngsaa LED/PAX400/4,2W/400lm/CRI>90
DALI BUS 2 - Addresses 00-49, Group 0
Ceiling lighting
21 pcs LCC60MCM controls 102 pcs LED/PAX400/4,2W/400lm/CRI>90
Decorative lighting 2 pcs LCC60MCM controls 6 pcs Lyngsaa LED/PAX400/4,2W/400lm/CRI>90
Wall lighting
2 pcs LCC60MCM controls 5 pcs LED/rep-kit/3W/250lm/CRI>90
Control panel 1
Scene 0 = 100%
Scene 1 = 25%
Scene 2 = 10%
Scene 3 = 5%
The panel is connected to 2 sceneDOT which controls the DALI BUS 1, Group 0.
The fading is set to 6 seconds. The following scenarios are set in the restaurant:
The bar
DALI BUS 2 - Addresses 00-51, Group 1
Ceiling lighting
3 pcs LCC60MCM controls 20 pcs Lyngsaa LED/PAX400/4,2W/400lm/CRI>90
Shelf lighting
2 pcs LCC60MCM controls 6 pcs Lyngsaa LED/PAX400/4,2W/400lm/CRI>90
Control panel 2
The panel is connected to 1 sceneDOT which controls the DALI BUS 2, Group 1.
And the fading is set to 6 seconds. The following scenarios are set in the bar:
Scene 0 = 100%
Scene 1 =
100% ceiling lighting
and shelves
50% front bar, ceiling
Scene 2 =
100% ceiling lighting
50% shelves
25% front bar, ceiling
14
Scene 3 =
100% ceiling lighting
50% shelves
10% front bar, ceiling
Vadsbo LightTech
LED-control Selection
LED-dimmers
UD100, LD220 and LD440
Universal push dimmers UD100, LD220 and LD440
Universal LED-dimmers for wallbox installation
that starts at 1W
A common problem - when dimming LED lamps and
CFL lamps - is that conventional dimmers usually
require a high minimum load of 50W, 35W or 20W,
while low energy light lamps and LED lamps have a power range from 1W up to 20W. For dimming of these
low energy lamps dimmers that can operate from 1W
and up are required. Vadsbo’s series of universal push
dimmers starts already at 1 W for dimming of both
lowpower lamps as well as electronic transformers,
dimmable LED-drivers and incandescent lamps.
Adjustable minimum dimming level
Depending on the type of load that is connected to
the dimmer, the dimmer’s lowest dimming level can
be adjusted to fit the load in question. The dimming
characteristic is distinguished between different types
of loads. This feature is perfect for use when there is
mixed loads of different lamptypes including dimmable
halogen and incandescent lights. It is also very handy
if the user at some future date decides to switch from
incandescent to 230 VAC dimmable LEDs. Then you
need only adjust the lowest dimming level to the new
load, instead of buying a new dimmer.
Memory function
Equipped with memory function that also remains after
power failure.
Download the
LightKey 2015
Vadsbo tests the
most common
dimmable 230V
LED on the market together with
our dimmers and
and summarizes
the results in the
annual LightKey!
Designation
UD100
LD220
LD440
Item number
V-4010020IB
V-4022010IB
V-4044020IB
Power
1-100W
1-200W
1-440W
Voltage
230 V +/-10% 50 Hz
230 V +/-10% 50 Hz
230 V +/-10% 50 Hz
Max current
0,43 A
0,87 A
1,91 A
- Dimmable 230V LED
- Dimmable LED driver for phase control
- Dimmable CFLs
- 230 V halogen lamps
- Electronic transformers
- Incandescent light
1-100W
1-100W
1-100W
1-100W
1-100W
1-100W
1-200W
1-200W
1-200W
1-200W
1-200W
1-200W
1-440W
1-440W
1-440W
1-440W
1-440W
1-440W
Has adjustable minimum dimming level
Yes
Yes
Yes
Memorises the last set brightness, even after
power failure
Yes
Yes
Yes
With motion detection / twilight relay / timer
Yes
Yes
Yes
Is controlled up to 5 reactive toggle switches
Yes
Yes
Yes
With soft start
Yes
Yes
Yes
Dimension
Ø56 H22 mm
Ø56 H22 mm
Ø56 H22 mm
For dimming of
Wider dimming range
Wider dimming range, starts alredy at 1 W
Excellent test ratings
0-100% dimming
Adjustable min. dimming level
Highest ratings in tests of 25 leading brands of 230 V LED-lamps.
Average rating 4,7 points out of 5. 15 lamps scoring 5 out of 5.
Different minimum settings possible for LED-lamps and CFL.
15
Vadsbo LightTech
LED-control Selection
LED-dimmers - Rotary type
PWM 360A
LED dimmer PWM 360A works with pulse width modulated current and dims constant voltage diodes from
1W to 360W with 12 Vdc and 24 Vdc power supply
from 15 to 360W.
Dimming LEDs from 1W ...
Light-emitting diodes are operating in low power
range from 1W and up. Dimming of light sources with
low power, necessitate dimmers that can operate from
as low as 1W. PWM 360A solves dimming problems at
these low loads.
... to 360W
For LED chandeliers or larger LED installations power
requirements are higher. PWM 360A solves dimming
problems at large loads of up to 360W.
... even in combination with Busch Jaeger fronts
PWM 360A can be combined with Busch Jaeger fronts
in designs glass, aluminum, gray, anthracite and white.
Power supplies for driving e.g. PWM360
Power supplies in 12-24 Vdc with power from 15W
to 360W. Also for DIN-rail mounting.
KED10VDA
Rotary type 1-10V Control module
KED10VDA is a 1-10 Vdc control module for contolling
dimmable electronic ballasts, LED drivers and electronic
transformers with 1-10Vdc input.
The KED10VDA is quiet and operate with high
efficiency.
• Max 10A
• Rotary type knob
• Protection against transients, overloads and
overtemperature
• EMC approved
• Dimensions 84x84x45 mm
LED-dimmer VD200
VD200 is a LED dimmer for 230V LED,
230V halogen- and incandescent lamps up to 200W,
dimmable LED-control gears and electronic
transformers. The minimum output is 1W.
PWM 360A can
be combined with
Busch Jaeger fronts
LED-dimmer VD600
VD600 is a versatile LED dimmer suited for
• Dimmable LED 10-300W
• 230V halogen 35-500W
• Incandescent and electronic transformer 35-600W
Power supplies for
driving PWM360
Designation
PWM 360A
KED10VDA
LED-dimmer VD200
LED dimmer VD600
Item number
V-4036020
V-40010A20DC
V-4020020TRL
V-4060020L
Power
1-360W
0,1-10A
1-200W
1-600W
For dimming of
Constant voltage diodes
Electronic ballasts,
LED drivers and electronic transformers with
1-10Vdc input.
Incandescent, 230V halogen, dimmable LED driver
and GV10 LED light,
electronic transformer.
Incandescent, 230V halogen, dimmable LED driver
and GV10 LED light,
electronic transformer.
Output
8-24 Vdc
(PWM modulated)
Push: 230V, on / off
Rotation: 1-10Vdc control
Dimming function
Rotation
Rotation
Rotation
Rotation
- ON/OFF
Yes
Yes
Push
Push
Colour
White
White
White
White
Dimension
84x84x45 mm
84x84x45 mm
84x84x45 mm
84x84x45 mm
16
Vadsbo LightTech
LED-control Selection
Du0TM driving and dimming 12Vac LED
LD220
ZERO 35
12 VAC LED
100% of dimmable
99% of non-dimmable*
A new concept in dimming of 12VAC LED
The combination of LD220 + ZERO, 0 Watt transformers - Du0TM generates a unique profile of the phase
angle control of 12 Vac LED lights.
The result is that 100% of 12Vac dimmable LED lights
and 99% of non-dimmable 12Vac LED lights are dimmed in an excellent manner. Additionally ZERO 35 +
LD220 fits in a wall-box!
The first component of Du0TM - UD100, LD220 and
440, universal low power dimmers
Vadsbo´s universal low-power LED- dimmers will excellently dim all types of light sources such as dimmable
CFLs and LEDs from low power up to 440W.
Depending on the power factor of each lamp over
20 pcs 9W 230Vac dimmable LED lights can be dimmed with LD220 for example.
The second component of Du0TM - ZERO, 0 WATTs
electronic transformers
The 0 WATT transformers ZERO 35 and 70 starts
already at 0W. ZERO 35 is made in box-shape and fits
into a wall box which facilitates the installation work.
A conventional dimmer switch that starts at 20-35W
is unable to deliver enough low RMS voltage for low
power LED lamps with power from 3W and up.
The combination UD100 / LD220 / LD440 which starts
already at 1W and the ZERO transformers, starting at
0W, provide the sufficiently low RMS voltage level.
Universal push
dimmer UD100
V-4010020IB
Universal push
dimmer LD220
V-4022010IB
0 WATT transformer ZERO 70
V-1507020Z
Universal push
dimmer LD440
V-4044020IB
0 WATT transformer ZERO 35
V-1503520RZ
Dimmable LED lamps typically have a built-in PWM-like
feature that allows them to be dimmed which is not
the case with non-dimmable LED lights.
Du0TM emulates PWM dimming, so even non-dimmable
LED lamps will be dimmed in an excellent manner.
The Du0™-concept
17
Vadsbo LightTech
LED-control Selection
Notes
18
Vadsbo LightTech
LED-control Selection
Notes
NOTE that this document contains QR codes, to read
these download a QR reader to your smartphone or
tablet, then scan the QR code. You need access to the
internet to access the material. All material is available
at www.vadsbo.net.
The content on these pages are subject to copyright
under the Berne Convention. None of the information
material may be reproduced for external use or transmitted in any form without written permission from
Vadsbo.
Technical specifications are subject to change without
notice. Data subject to change without notice.
All our products have a 2 year guarantee.
Editors: Sune Ågren, Johan Sandberg
Layout and original: Teresia Ågren
©2015 Vadsbo LightTech
2015-05-28
19
Vadsbo LightTech
LED-control Selection
Save time and money with the right tested combinations of
Dimmer
Vadsbo LightTech
Aröds Industriväg 34
422 43 Hisings Backa
Sweden
Phone +46-31-23 56 00
Fax
+46-31-22 60 10
info@vadsbo.net
www.vadsbo.net
Driver
Distributor:
Light source