SN75ALS199
QUADRUPLE DIFFERENTIAL LINE RECEIVER
SLLS046C – JANUARY 1989 – REVISED MAY 1995
D
D
D
D
D
D
D
D
D
Meets or Exceeds the Requirements of ITU
Recommendations V.10, V.11, X.26, and
X.27
Designed to Operate Up To 20 Mbaud
–7 V to 7 V Common-Mode Input Voltage
Range With 300-mV Sensitivity
3-State TTL-Compatible Outputs
High Input Impedance . . . 12 kΩ Min
Input Hysteresis . . . 120 mV Typ
Single 5-V Supply Operation
Low Supply Current Requirement
35 mA Max
Improved Speed and Power Consumption
Compared to MC3486
D OR N PACKAGE
(TOP VIEW)
1B
1A
1Y
1, 2EN
2Y
2A
2B
GND
1
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
VCC
4B
4A
4Y
3, 4EN
3Y
3A
3B
description
The SN75ALS199 is a monolithic, quadruple line receiver with 3-state outputs designed using advanced,
low-power, Schottky technology. This technology provides combined improvements in bar design, tooling
production, and wafer fabrication, providing significantly less power consumption and permitting much higher
data throughput than other designs. The device meets the specification of ITU Recommendations V.10, V.11,
X.26, and X.27.
The SN75ALS199 features 3-state outputs that permit direct connection to a bus-organized system with a
fail-safe design that ensures the ouptuts will always be high if the inputs are open. The device is optimized for
balanced multipoint bus transmission at rates up to 20 megabits per second. The input features high-input
impedance, input hysteresis for increased noise immunity, and an input sensitivity of ± 300 mV over a
common-mode input voltage range of ± 7 V. It also features an active-high enable function for each of two
receiver pairs. The SN75ALS199 is designed for optimum performance when used with the SN75ALS194
quadruple, differential line driver.
The SN75ALS199 is characterized for operation from 0°C to 70°C.
FUNCTION TABLE
(each receiver)
EN
OUTPUT
Y
VID ≥ 0.3 V
– 0.3 V < VID < 0.3 V
H
H
H
?
VID ≤ – 0.3 V
X
H
L
L
Z
Open
H
H
DIFFERENTIAL INPUTS
A–B
H = high level, L = low level, X = irrelevant,
? = indeterminate, Z = high impedance (off)
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  1995, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SN75ALS199
QUADRUPLE DIFFERENTIAL LINE RECEIVER
SLLS046C – JANUARY 1989 – REVISED MAY 1995
logic symbol†
1, 2EN
1A
1B
2A
2B
3, 4EN
3A
3B
4A
4B
logic diagram
4
1, 2EN
EN
2
3
1
6
5
7
12
1A
1Y
1B
2Y
2A
2B
4
2
3
1
1Y
6
5
7
2Y
EN
10
11
9
14
13
15
3Y
3, 4EN
4Y
3A
3B
† This symbol is in accordance with ANSI/IEEE Std 91-1984
and IEC Publication 617-12.
4A
4B
12
10
9
11
14
15
13
3Y
4Y
schematics of inputs and outputs
EQUIVALENT OF EACH A OR B INPUT
VCC
EQUIVALENT OF EACH ENABLE INPUT
TYPICAL OF ALL OUTPUTS
VCC
VCC
3 kΩ
3 kΩ
50 Ω
5 kΩ
22 kΩ
18 kΩ
40 kΩ
Input
Output
Input
300 kΩ
VCC (A)
or
GND (B)
2
150 kΩ
2 kΩ
50 Ω
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1.5 kΩ
SN75ALS199
QUADRUPLE DIFFERENTIAL LINE RECEIVER
SLLS046C – JANUARY 1989 – REVISED MAY 1995
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage, VI (A or B inputs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±15 V
Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±15 V
Enable input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Low-level output current, IOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA
Continuous total dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential input voltage, are with respect to network ground terminal.
2. Differential input voltage is measured at the noninverting input with respect to the corresponding inverting input.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
DERATING
FACTOR
TA = 70°C
POWER RATING
D
950 mW
7.6 mW/°C
608 mW
N
1150 mW
9.2 mW/°C
736 mW
recommended operating conditions
Supply voltage, VCC
MIN
NOM
MAX
UNIT
4.75
5
5.25
V
±7
V
±12
V
Common-mode input voltage, VIC
Differential input voltage, VID
High-level input voltage, VIH
2
Low-level input voltage, VIL
V
0.8
High-level output current, IOH
Low-level output current, IOL
Operating free-air temperature, TA
0
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
V
– 400
µA
16
mA
70
°C
3
SN75ALS199
QUADRUPLE DIFFERENTIAL LINE RECEIVER
SLLS046C – JANUARY 1989 – REVISED MAY 1995
electrical characteristics over recommended ranges of common-mode input voltage, supply
voltage, and operating free-air temperature (unless otherwise noted)
PARAMETER
VIT +
VIT –
Positive-going input threshold voltage
Vhys
VIK
Hysteresis voltage (VIT+ – VIT–)
VOH
High-level output voltage
TEST CONDITIONS
II = – 18 mA
VID = 300 mV,
Low level output voltage
Low-level
VID = – 300 mV
IOZ
High impedance state output current
High-impedance-state
VIL = 0.8 V,
VIL = 0.8 V,
II
Line input current
Other input at 0 V,,
See Note 3
IIH
High level enable
High-level
enable-input
input current
IIL
Low-level enable-input current
UNIT
300
mV
mV
mV
– 1.5
IOH = – 400 µA
IOL = 8 mA
VID = – 3 V,
VIO = 3 V,
2.7
3.6
0.5
20
– 20
VO = 0.5 V
VI = 15 V
VI = – 15 V
VIH = 2.7 V
0.7
1.2
–1
– 1.7
20
100
VIH = 5.25 V
VIL = 0.4 V
– 100
VID = 3 V,
VO = 0
12
18
– 15
– 78
V
V
0.45
IOL = 16 mA
VO = 2.7 V
Input resistance
Short-circuit output current§
MAX
120
VOL
IOS
TYP†
– 300‡
Negative-going input threshold voltage
Enable-input clamp voltage
MIN
V
µA
mA
µA
µA
kΩ
– 130
mA
ICC
Supply current
Outputs disabled
22
35
mA
† All typical values are at VCC = 5 V, TA = 25°C.
‡ The algebraic convention, in which the less positive limit is designated minimum, is used in this data sheet for threshold voltage levels only.
§ Not more than one output should be shorted at a time, and the duration of the short circuit should not exceed one second.
NOTE 3: Refer to ITU Recommendations V.10 and V.11 for exact conditions.
switching characteristics, VCC = 5 V, TA = 25°C
PARAMETER
TEST CONDITIONS
tPLH
tPHL
Propagation delay time, low- to high-level output
tPZH
tPZL
Output enable time to high level
tPHZ
tPLZ
Output disable time from high level
4
Propagation delay time, high- to low-level output
Output enable time to low level
Output disable time from low level
VID = 0 V to 3 V,,
See Figure 2
CL = 15 pF,,
CL = 15 pF,
pF
See Figure 3
pF
CL = 15 pF,
See Figure 3
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MIN
TYP
MAX
15
22
15
22
13
25
11
25
13
25
15
22
UNIT
ns
ns
ns
SN75ALS199
QUADRUPLE DIFFERENTIAL LINE RECEIVER
SLLS046C – JANUARY 1989 – REVISED MAY 1995
PARAMETER MEASUREMENT INFORMATION
VID
VOH
VOL
IOH
(–)
IOL
(+)
2V
Figure 1. VOH and VOL Test Circuit
Generator
(see Note A)
Output
50 Ω
CL = 15 pF
(see Note B)
3V
Input
1.5 V
1.5 V
0V
tPLH
tPHL
VOH
1.5 V
Output
1.3 V
1.3 V
VOL
2V
TEST CIRCUIT
VOLTAGE WAVEFORMS
NOTES: A. The input pulse is supplied by a generator having the following characteristics: PRR ≤ 1 MHz, duty cycle ≤ 50%, ZO = 50 Ω,
tr ≤ 6 ns, tf ≤ 6 ns.
B. CL includes probe and jig capacitance.
Figure 2. Test Circuit and Voltage Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SN75ALS199
QUADRUPLE DIFFERENTIAL LINE RECEIVER
SLLS046C – JANUARY 1989 – REVISED MAY 1995
PARAMETER MEASUREMENT INFORMATION
SW1
2.5 V
Output
– 2.5 V
SW2
2 kΩ
5V
CL = 15 pF
(see Note B)
Generator
(see Note A)
5kΩ
See Note C
SW3
51 Ω
TEST CIRCUIT
3V
3V
SW1 to 2.5 V
1.5 V SW2 Open
SW3 Closed
0V
Input
Input
1.5 V
0V
tPZH
tPZL
VOH
Output
4.5 V
1.5 V
Output
1.5 V
0V
tPZH
tPZL
SW1 to 2.5 V
SW2 Closed
SW3 Closed
1.5 V
Input
1.5 V
0V
tPHZ
Output
VOL
3V
SW1 to – 2.5 V
SW2 Closed
SW3 Closed
0V
3V
Input
SW1 to – 2.5 V
SW2 Closed
SW3 Open
tPLZ
1.4 V
VOH
0.5 V
Output
0.5 V
VOL
1.4 V
tPHZ
tPLZ
VOLTAGE WAVEFORMS
NOTES: A. The input pulse is supplied by a generator having the following characteristics: PRR ≤ 1 MHz, duty cycle ≤ 50%, ZO = 50 Ω,
tr ≤ 6 ns, tf ≤ 6 ns.
B. CL includes probe and jig capacitance.
C. All diodes are 1N3064 or equivalent.
Figure 3. Test Circuit and Voltage Waveforms
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN75ALS199
QUADRUPLE DIFFERENTIAL LINE RECEIVER
SLLS046C – JANUARY 1989 – REVISED MAY 1995
TYPICAL CHARACTERISTICS
OUTPUT VOLTAGE
vs
ENABLE VOLTAGE
OUTPUT VOLTAGE
vs
ENABLE VOLTAGE
4
VID = 300 mV
VIC = 0
RL = 8 kΩ to GND
TA = 25°C
4.5
VO – Output Voltage – V
4
TA = 70°C
TA = 25°C
TA = 0°C
3.5
VCC = 5.5 V
3
VCC = 5 V
VO – Output Voltage – V
5
3.5
VCC = 4.5 V
3
2.5
2
1.5
2.5
2
1.5
1
VCC = 5 V
VID = 300 mV
VIC = 0
RL = 8 kΩ to GND
1
0.5
0.5
0
0
0
0.5
1
1.5
2
2.5
0
3
0.5
1
2
2.5
3
Enable Voltage – V
Enable Voltage – V
Figure 5
Figure 4
OUTPUT VOLTAGE
vs
ENABLE VOLTAGE
OUTPUT VOLTAGE
vs
ENABLE VOLTAGE
6
6
VCC = 5.5 V
VCC = 5 V
5
VID = – 300 mV
VIC = 0
RL = 1 kΩ to VCC
TA = 25°C
5
VO – Output Voltage – V
VCC = 4.5 V
VO – Output Voltage – V
1.5
4
3
2
TA = 0°C
TA = 25°C
4
TA = 70°C
3
2
VCC = 5 V
VIC = – 300 mV
VIC = 0
RL = 1 kΩ to VCC
1
1
0
0
0
0.5
1
1.5
2
2.5
3
0
0.5
1
1.5
2
2.5
3
Enable Voltage – V
Enable Voltage – V
Figure 7
Figure 6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
SN75ALS199
QUADRUPLE DIFFERENTIAL LINE RECEIVER
SLLS046C – JANUARY 1989 – REVISED MAY 1995
TYPICAL CHARACTERISTICS
HIGH-LEVEL OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
OUTPUT VOLTAGE
vs
DIFFERENTIAL INPUT VOLTAGE
4
5
VOH – High-Level Output Voltage – V
4
VO – Output Voltage – V
IOH = 0
VCC = 5 V
VIC = – 12 V to 12 V
IO = 0
TA = 25°C
3
2
VIT –
VIT +
1
0
– 200 – 150 – 100 – 50
IOH = – 400 µA
3
2
1
VCC = 5 V
VID = 300 mV
VIC = 0
0
0
50
100
150
200
0
10
20
Figure 8
60
70
80
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
5
VIC = 0
VID = 300 mV
TA = 25°C
4.5
4
3.5
VCC = 5.5 V
3
VCC = 5 V
2.5
VCC = 4.5 V
2
1.5
1
VOH – High-Level Output Voltage – V
5
VOH – High-Level Output Voltage – V
50
Figure 9
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
VCC = 5 V
VID = 300 mV
VIC = 0
4.5
4
3.5
3
TA = 0°C
2.5
TA = 25°C
2
TA = 70°C
1.5
1
0.5
0.5
– 10 – 20 – 30 – 40 – 50 – 60 – 70 – 80 – 90 – 100
IOH – High-Level Output Current – mA
0
0
– 10 – 20 – 30 – 40 – 50 – 60 – 70 – 80 – 90 –100
IOH – High-Level Output Current – mA
Figure 11
Figure 10
8
40
TA – Free-Air Temperature – °C
VID – Differential Input Voltage – mV
0
0
30
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN75ALS199
QUADRUPLE DIFFERENTIAL LINE RECEIVER
SLLS046C – JANUARY 1989 – REVISED MAY 1995
TYPICAL CHARACTERISTICS
LOW-LEVEL OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
0.4
VCC = 5 V
VID = – 300 mV
VIC = 0
VOL – Low-Level Output Voltage – V
0.35
0.3
0.25
IO = 8 mA
0.2
0.15
IO = 0
0.1
0.05
0
0
10
20
30
40
50
60
70
80
TA – Free-Air Temperature – °C
Figure 12
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
0.8
0.8
VCC = 4.5 V
VCC = 5 V
0.6
TA = 70°C
0.7
VOL – Low-Level Output Voltage – V
VOL – Low-Level Output Voltage – V
0.7
VCC = 5.5 V
0.5
0.4
0.3
0.2
VIC = 0
VID = – 300 mV
TA = 25°C
0.1
TA = 25°C
0.6
0.5
TA = 0°C
0.4
0.3
0.2
VCC = 5 V
VID = – 300 mV
VIC = 0
0.1
0
0
0
10
20
30
40
50
60
70
80
IOL – Low-Level Output Current – mA
0
10
20
30
40
50
60
70
80
IOL – Low-Level Output Current – mA
Figure 13
Figure 14
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
SN75ALS199
QUADRUPLE DIFFERENTIAL LINE RECEIVER
SLLS046C – JANUARY 1989 – REVISED MAY 1995
TYPICAL CHARACTERISTICS
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
50
40
VCC = 5.5 V
25
I CC – Supply Current – mA
45
I CC – Supply Current – mA
30
VID = – 300 mV
VIC = 0
IO = 0
TA = 25°C
35
30
Disabled
25
Enabled
20
15
10
VCC = 5 V
20
VCC = 4.5 V
15
10
VID = – 300 mV
Outputs Enabled
IO = 0
5
5
0
0
1
2
3
4
5
6
7
0
8
0
10
VCC – Supply Voltage – V
20
30
80
40
35
VCC = 5.5 V
25
VCC = 5 V
I CC – Supply Current – mA
I CC – Supply Current – mA
70
SUPPLY CURRENT
vs
FREQUENCY
30
20
VCC = 4.5 V
15
10
IO = 0
Outputs Enabled
VIC = 0
TA = 25°C
– 100
30
VCC = 5 V
VI = ± 1.5-V Square Wave
CL = 15 pF
Four Channels Driven
TA = 25°C
25
20
15
10
5
0
100
200
0
10 k
VID – Differential Input Voltage – mV
100 k
1M
f – Frequency – Hz
Figure 18
Figure 17
10
60
Figure 16
SUPPLY CURRENT
vs
DIFFERENTIAL INPUT VOLTAGE
0
– 200
50
TA – Free-Air Temperature – °C
Figure 15
5
40
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
10 M
100 M
SN75ALS199
QUADRUPLE DIFFERENTIAL LINE RECEIVER
SLLS046C – JANUARY 1989 – REVISED MAY 1995
TYPICAL CHARACTERISTICS
INPUT CURRENT
vs
INPUT VOLTAGE TO GND
INPUT RESISTANCE
vs
FREE-AIR TEMPERATURE
3
30
TA = 25°C
2
I I – Input Current – mA
ri – Input Resistance – k Ω
25
20
15
10
0
–1
–2
5
0
1
0
10
20
30
40
50
60
70
–3
– 20
80
– 15
– 10
0
5
10
15
20
VI – Input Voltage to GND – V
TA – Free-Air Temperature – °C
Figure 19
Figure 20
SWITCHING TIME
vs
FREE-AIR TEMPERATURE
PROPAGATION DELAY TIME
vs
SUPPLY VOLTAGE
30
20
VCC = 5 V
CL = 15 pF
18
t pd – Propagation Delay Time – ns
tPLH
25
tPLZ
Switching Time – ns
–5
20
tPHZ
tPZH
15
tPHL
10
tPZL
tPHZ
tPZH
5
CL = 15 pF
TA = 25°C
16
tPHL
14
tPLH
12
10
8
6
4
2
0
0
10
20
30
40
50
60
70
80
0
4.5
4.6
4.7
TA – Free-Air Temperature – °C
4.8
4.9
5
5.1
5.2
5.3 5.4
5.5
VCC – Supply Voltage – V
Figure 21
Figure 22
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
PACKAGE OPTION ADDENDUM
www.ti.com
10-Jun-2014
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
SN75ALS199D
ACTIVE
SOIC
D
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
75ALS199
SN75ALS199DR
ACTIVE
SOIC
D
16
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
75ALS199
SN75ALS199N
ACTIVE
PDIP
N
16
25
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
0 to 70
SN75ALS199N
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
10-Jun-2014
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Mar-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
SN75ALS199DR
Package Package Pins
Type Drawing
SOIC
D
16
SPQ
Reel
Reel
Diameter Width
(mm) W1 (mm)
2500
330.0
16.4
Pack Materials-Page 1
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
6.5
10.3
2.1
8.0
W
Pin1
(mm) Quadrant
16.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Mar-2008
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
SN75ALS199DR
SOIC
D
16
2500
333.2
345.9
28.6
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated