NXT
LN10RAT-W
WET LOCATION
40° ADJUSTABLE
®
PROJECT INFORMATION
PROJECT
Covered By US Patent 8,215,805
DATE
TYPE
LN10RAT-W
NanoLED NXT Wet Location Recessed Adjustable - Available with up to 925 delivered lumens at 20W (47LPW). The NanoLED NXT
provides maximum delivered lumens and optical performance through the optimization of thermal, optical and LED science in the smallest possible
aperture. 40° adjustability with our patented hot-aiming mechanism makes NanoLED NXT the best choice for direct replacement and substitution of
MR16 sources.
1-7/8" Regress Trim
DELIVERED PERFORMANCE
®
14 Watts
NXT
20 Watts
90+
90+
80+ HIGH 80+ HIGH
Color Rendering Index
CRI
CRI
CRI
CRI
Lumens per Watt
51
40
47
37
Source Lumens
1100 875 1500 1200
Delivered Lumens
725
575
925
750
Center Beam Candle Power 7200 5775 9275 7425
Color Consistency
2-Step MacAdam Ellipse
21⁄2” Ø
Performance based on 3000K
315⁄16” Ø
ADJUSTABLE
2700K
CCT MULTIPLIER
Color Rendering Index
Multiplier for
Lumen Output
80+
CRI
90+
HIGH
CRI
1.00
0.73
3000K
3500K 4000K
80+
CRI
90+
HIGH
CRI
80+
CRI
80+
CRI
1.00
.80
1.15
1.07
Plan View
HOW TO SPECIFY
Ordering Example: Specify trim code and housing code to order: LN10RAT-WBM- MTG214- 27KS - 25 - 10 - LNC61 - 120V - DIML2 - CB27 - BOFD
TRIM ORDERING INFORMATION
TRIM
LN10RAT
LIGHT
ENGINE
BAFFLE OPTIONS
–
LN10RAT
Round
Adjustable
Accent,
Trimmed
Wet
Location
–
WBM Black Matte Baffle
Wet Listed
WWM White Matte Baffle
Wet Listed
REFLECTOR
COLOR
WATTAGE
–
MTG2
______
MTG2
14 14W LED
20 20W LED
–
Standard CRI 80+
27KS 2700K, 80+ CRI
30KS 3000K, 80+ CRI
35KS 3500K, 80+ CRI
TRIM FINISH
–
10 10° Distribution
25 25° Distribution
High CRI 90+
27KH 2700K, 90+ CRI
30KH 3050K, 90+ CRI
10
13
21
28
RAL
White
Statuary Bronze
Black
Metalized Grey
Special Color
(specify RAL#)
2 Step MacAdam ellipse
is standard
HOUSING ORDERING INFORMATION
HOUSING
–
New Construction
LNC61 DL, Adj, WW / Max. ceiling thickness: 7/8"
LNC63 DL, Adj 30°, WW / Max. ceiling thickness: 1-1/4"
LNC65 DL, Adj 20° / Max. ceiling thickness: 1-1/2"
LSH41 Adj 40° / Max. ceiling thickness: 7/8"
LSH43 DL, Adj 30°, WW / Max. ceiling thickness: 1-1/4"
IC / Airtight
LIC1 DL, Adj, WW / Max ceiling thickness: 7/8"
LIC3 DL, Adj 30°, WW / Max. ceiling thickness: 1-1/4"
LIC5 DL, Adj 20° / Max. ceiling thickness: 1-1/2"
Chicago Plenum
LCP1 DL, Adj, WW / Max. ceiling thickness: 7/8"
LCP3 DL, Adj 30°, WW / Max. ceiling thickness: 1-1/4"
LCP5 DL, Adj 20° / Max. ceiling thickness: 1-1/2"
See next page for all housing dimensions
USAI
Lighting
®
DRIVER 2
VOLTAGE
www.usailighting.com
info@usailighting.com
ACCESSORIES
–
120V
277V
–
DIML2 0-10V Low voltage 10%
DIML3 Lutron Hi-Lume 1%
2-wire, 120V only
DIML4 Lutron Hi-Lume 1%
3-wire/ECO
DIML6A ELDO 0-10V 0.1%,
logarithmic
DIML6B ELDO 0-10V 0.1%,
linear
DIML7 ELDO DALI 0.1%
DIML9 TRIAC 15%, 120V only
DIML10 ELV 15%, 120V only
2
On/off driver provided if left blank
1126 River Road
New Windsor, NY 12553
OPTICAL ACCESSORIES
–
CB27 27" C-Channel Bars
CB52 52" C-Channel Bars
TZ Tech Zone Ceiling Compatible
(LSH43 housing only)
EMLW Emergency battery,
Wet Location 2
AL20D
AL30D
AL40D
AL55D
AL80D
AS61C
BOFD
SOFD
PRFD
HEXD
Refer to optical accessories
matrix on next page for
resulting beamspreads
whenaccessory
lens is combined
with 10° and 25°
optics
Borosilicate Frosted
Solite Frosted
Prismatic Frosted
Hex Cell Louver 1/8"
2 Requires above ceiling access for service. Not
for use with LCP and LIC housings.
T 845–565–8500
F 845–561–1130
© 2013. USAI, LLC.
All rights reserved.
All designs protected by copyright.
Revised 04/08/2015
WET LOCATION
40° ADJUSTABLE
®
NXT
LN10RAT-W
Covered By US Patent 8,215,805
TRIM INFORMATION
NanoLED Optical Accessories Matrix
if you want…
and you have….
10°
25°
15° beam
AL10D N/A
20° beam
AL15D N/A
25° beam
AL20D N/A
30° beam
AL30D AL20D
35° beam
AL40D AL30D
40° beam
AL55D AL40D
45° beam
AL80D AL55D
20x40° beam
AS61D N/A
35x45° beam
N/A
AS61D
Borosilicate Frosted Lens BOFD BOFD
Solite Frosted Lens
SOFD
SOFD
Prismatic Frosted Lens
PRFD
PRFD
1/8" Hexcell Louver
HEXD HEXD
size D size D
CP / Chicago Plenum - CCEA Approved
New Construction
LCP1 - DL / ADJ 40° / WW
LSH41 - DL / ADJ 40° / WW
7
(Max. Ceiling Thickness - /8")
(Max. Ceiling Thickness - 7/8")
LCP3 - DL / ADJ 30° / WW
LSH43 - DL / ADJ 30° / WW
1
(Max. Ceiling Thickness - 1 /4")
(Max. Ceiling Thickness - 11/4")
LCP5 - DL / ADJ 20°
(Max. Ceiling Thickness - 11/2")
Wet Listed
21⁄2” Ø
21⁄2” Ø
315⁄16” Ø
315⁄16” Ø
Plan View
HOUSING INFORMATION
New Construction
LNC61 - DL / ADJ 40° / WW
(Max. Ceiling Thickness - 7/8")
LNC63 - DL / ADJ 30° / WW
(Max. Ceiling Thickness - 11/4")
LNC65 - DL / ADJ 20°
(Max. Ceiling Thickness - 11/2")
IC / Airtight
LIC1 - DL / ADJ 40° / WW
(Max. Ceiling Thickness - 7/8")
LIC3 - DL / ADJ 30° / WW
(Max. Ceiling Thickness - 11/4")
LIC5 - DL / ADJ 20°
(Max. Ceiling Thickness - 11/2")
51/8" (40°)
57/8" (0°)
77/16"
63/4"
77/16"
LSH41 = 7/8"
LSH43 = 1-1/4"
41/2"
131/4"
51/4"
12"
12"
117/8"
171/2"
163/8"
175/8"
175/8"
SPECIFICATIONS
TRIM: 2-1/2" round aperture with a 1-7/8" regressed lens
and 3/4" flange, retained by three mounting clips. Trim finish
is available in White, Statuary Bronze, Black, and Metalized
Grey finishes. Custom color flanges available (provide
RAL#).
AIMING MEMORY FEATURE: Unique patented vertical and
horizontal aiming memory feature allows users to remove
trim for reflector or accessory change without disturbing
the set and locked lamp position. Trim is also keyed to
housing to maintain aiming position.
BAFFLE OPTIONS: Black or white matte high temperature
nylon baffles available for wet location.
RATED LIFE: Based on IESNA LM80-2008 50,000 hours at
70% lumen maintenance (L70).
TRIM LENS: Wet location 10° and 25° trims are shipped
with clear lens at baffle, 25° has solite lens installed in
accessory holder.
THERMAL MANAGEMENT: Proprietary high performance
aluminum die cast heatsink for maximum LED life. Ambient
temperatures at fixture location should not exceed 40°C
during normal operation.
REFLECTOR: Interchangeable tool-less reflector system
allows for flexibility while maintaining design consistency.
Available in 10° and 25° beam distribution.
ADJUSTMENT: True Hot Aiming with center beam optics
is adjustable with 1/8" Allen screw driver. Simple recessed
angled screws enable adjustment of vertical aiming and
horizontal rotation from below, without trim removal. 362°
locking rotation, with 0° - 40° locking vertical tilt.
FIELD REPLACEABLE LIGHT ENGINE: Available in
14W (775 delivered lumens) and 20W (925 delivered
lumens). Engine is field replaceable through the aperture
with screwdriver.
COLOR: NanoLED NXT is available in 3 color temperatures
(2700K, 3000K, 3500K). All color options are tightly binned
for fixture-to-fixture color consistency within a 2-Step
MacAdam Ellipse. 80+ and 90+ color rendering index
available.
USAI
Lighting
®
www.usailighting.com
info@usailighting.com
FIELD REPLACEABLE DRIVER: Solid state electronic
constant current driver with a high power factor provided
standard. Specify 120V or 277V. Driver complies with IEEE
C62.41 surge protection.
DIMMING OPTIONS: Multiple dimming drivers available.
See compatibility chart attached. Some on-time delay may
be experienced depending on control system used. NOTE:
DIML6A logarithmic control is intended for use with Lutron
control systems; DIML6B linear control is intended for use
with non-lutron controls. DIML2 and DIML6 dimming drivers
source 2mA.
MOUNTING: Butterfly brackets and adjustable
nailer bars with integral nails provided. Nailer bars
are extendible from 14" to 24" centers.
HOUSING: Universal housing style allows the ability
to swap trim styles between Downlight, Adjustable
and Wall Wash. See Plug-and-Play limitations on
drawings above. Fabricated of 20 ga. black powder
coated steel with thru wire J-box, 2 in 2 out at min.
90°C, #12 AWG thru branch circuit wiring. LSH43
housing is compatible with Tech Zone ceilings.
ACCESSORY HOLDER: 360° rotating, "D" size
accessory holder. Maximum 2 lenses.
CEILING CUT OUT: 3-1/2" Ø
LISTINGS: Wet location listed.NRTL Tested to UL
Standards. IBEW Union made.
WARRANTY: 5 years
NOTES:
• Interior use only.
PHOTOMETRICS: Consult factory or website for IES
files. Tested in accordance with IESNA LM79-2008.
EMERGENCY: Emergency lighting battery pack with
remote test switch for wet locations requires above ceiling
access. Bodine BSL17C-C2 provides 260mA for 90 minutes;
delivers ~550-600 lumens. EM not available with LCP and LIC
housings.
1126 River Road
New Windsor, NY 12553
T 845–565–8500
F 845–561–1130
© 2013. USAI, LLC.
All rights reserved.
All designs protected by copyright.
Revised 04/08/2015
WET LOCATION
40° ADJUSTABLE
®
NXT
LN10RAT-W
Covered By US Patent 8,215,805
DELIVERED PERFORMANCE
LN10RAT-W 14W 30KS 10°
LN10RAT-W 20W 30KS 10°
USAI
Lighting
®
www.usailighting.com
info@usailighting.com
1126 River Road
New Windsor, NY 12553
T 845–565–8500
F 845–561–1130
© 2013. USAI, LLC.
All rights reserved.
All designs protected by copyright.
Revised 04/08/2015
40° ADJUSTABLE
®
LN10RAT / LN10RAL
NXT
DELIVERED PERFORMANCE
LN10RAT-W 14W 30KS 25°
LN10RAT-W 20W 30KS 25°
USAI
Lighting
®
www.usailighting.com
info@usailighting.com
1126 River Road
New Windsor, NY 12553
T 845–565–8500
F 845–561–1130
© 2013. USAI, LLC.
All rights reserved.
All designs protected by copyright.
Revised 11/14/2014
DIMMING DRIVER COMPATIBILITY
SELECTION GUIDE
DIML2
®
USAI
Lighting
DIMMING DRIVER WIRING SCHEMES:
NOTES:
Wiring diagrams are examples of typical installations intended to illustrate the number of wires that must be run to fixture. These diagrams are
not intended to specify all equipment necessary for a given dimming circuit. Refer to specific dimmer manufacturer's documentation for details.
IMPORTANT SAFETY INSTRUCTIONS
- SAVE THESE INSTRUCTIONS
1. Keep these instructions in a safe place for future reference.
2. Only qualified electricians in accordance to local codes should install these fixtures.
3. De-energize the electrical circuit at the circuit breaker prior to installation process or servicing.
4. Make sure all connections are in accordance with the National Electrical Code and any local regulations.
5. Cap any wires not used separately (not together).
DIML2 LED: 0-10V Dimming Driver Wiring (Dims down to 10%)
DIML2 Dimmer Compatibility Chart
Manufacturer
120V / 277V
Crestron
Crestron
Crestron
Crestron
Crestron
Leviton
Lightolier (Philips)
Lutron
Product
Part Number
Dimmed Light
Output Range
iLux dimmer expansion module
DIN Rail dimmer
DIN Rail analog output module
8 Channel dimmer module
8 Channel dimmer module
IllumaTech dimmer
Vega
Diva
CLS-EXP-DIMFLV
DIN-4DIMFLV4
DIN-A08
GLX-DIMFLV8
GLXP-DIMFLV8
IP710-DLX
V2000FAMU
DVTV-XX
100% - 10%
100% - 10%
100% - 10%
100% - 10%
100% - 10%
100% - 10%
100% - 10%
100% - 10%
Qty Fixtures
Per Dimmer*
Use source current per
fixture specification
sheet to determine
number of fixtures per
dimmer. Max number
of fixtures is limited by
dimmer load rating.
* NOTE: Refer to dimmer manufacturer's documentation for installation instructions and circuit details.
DIML2
0-10V DIMMING W/RELAY TO SWITCH POWER
FIXTURE
DIMMER: 0-10V
(BY OTHERS)
0-10V (-)
GRAY
0-10V (+)
PURPLE
SWITCHED HOT
BLACK
NEUTRAL
WHITE
LED
DRIVER
V+
RED
V-
BLACK
NOTE:
If switched, non-dimming operation is desired,
cap off purple and gray wires individually at
installation. Do NOT cap purple and gray wires
together.
GREEN
GND
CLASS 2 CONTROL WIRES
LINE
RELAY
(BY OTHERS)
NEUTRAL
DIMMER: 0-10V w/
POWER SWITCHING
DIML2
0-10V DIMMING (NO RELAY)
FIXTURE
(BY OTHERS)
LINE
0-10V (-)
GRAY
0-10V (+)
PURPLE
SWITCHED HOT
BLACK
NEUTRAL
WHITE
LED
DRIVER
V+
RED
V-
BLACK
NOTE:
If switched, non-dimming operation is desired,
cap off purple and gray wires individually at
installation. Do NOT cap purple and gray wires
together.
GREEN
GROUND
GND
NEUTRAL
USAI
Lighting
®
www.usailighting.com
info@usailighting.com
1126 River Road
New Windsor, NY 12553
T 845–565–8500
F 845–561–1130
© 2016. USAI, LLC.
All rights reserved.
All designs protected by copyright.
I2-264-2 Revised 02/15/2016
DIMMING DRIVER COMPATIBILITY
SELECTION GUIDE
DIML3
®
USAI
Lighting
DIMMING DRIVER WIRING SCHEMES:
NOTES:
Wiring diagrams are examples of typical installations intended to illustrate the number of wires that must be run to fixture. These diagrams are
not intended to specify all equipment necessary for a given dimming circuit. Refer to specific dimmer manufacturer's documentation for details.
IMPORTANT SAFETY INSTRUCTIONS
- SAVE THESE INSTRUCTIONS
1. Keep these instructions in a safe place for future reference.
2. Only qualified electricians in accordance to local codes should install these fixtures.
3. De-energize the electrical circuit at the circuit breaker prior to installation process or servicing.
4. Make sure all connections are in accordance with the National Electrical Code and any local regulations.
5. Cap any wires not used separately (not together).
DIML3 LED: Lutron Hi-Lume A-Series 2 Wire Fwd Phase (with neutral) / LED Dimming Driver Wiring (Dims down to 1%) 120V only.
DIML3 Dimmer Compatibility Chart
Manufacturer
120V Only
ETC
ETC
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Product
Part Number
Dimmed Light
Output Range
Sensor+ Cabinet
Unison DRd Cabinet
Maestro Wireless® 600W dimmer
Maestro Wireless® 1000W dimmer
HomeWorks® QS adaptive dimmer
HomeWorks® QS 600W dimmer
HomeWorks® QS 1000 W dimmer
Caseta Wireless® Pro 1000W dimmer
Stanza® dimmer
RadioRA® 2 adaptive dimmer
RadioRA® 2 1000 W dimmer
myRoom DIN power module
HomeWorks® QS wallbox power module
Homeworks® DIN power module
HomeWorks® wallbox power module
GRAFIK Eye® QS control unit
GRAFIK Eye® 3000 control unit
RPM-4U module
RPM-4A module
GP dimming panels
Ariadni CL 250W dimmer
Diva CL 250W dimmer
Grafik T CL or RF CL dimmer
Nova T CL 250W dimmer
ELV10
ELV10
MRF2-6ND-120MRF2-10ND-120HQRD-6NAHQRD-6NDHQRD-10NDPD-10NXDSZ-6NDRRD-6NARRD-10NDMQSE-4A1-D
HQRJ-WPM-6D-120LQSE-4A1-D
HWI-WPM-6D-120
QSGR-, QSGRJGRX-3100-, GRX-3500HW-RPM-4U-120, LP-RPM-4U-120
HW-RPM-4A-120, LP-RPM-4A-120
Various
AYCL-253PDVCL-253P-, DVSCCL-253PGT-250M-, GTJ-250MNTCL-250-
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100%-1%
100%-1%
100%-1%
100%-1%
Qty Fixtures Per Dimmer*
Fixture Wattage
39W and Less 40W - 80W
1 – 26
1 – 13
1 – 26
1 – 13
1–8
1–4
1 – 13
1–6
1–8
1–4
1–8
1–4
1 – 13
1–6
1 – 13
1–6
1–8
1–4
1–8
1–4
1–6
1–3
1–6
1–3
1 – 26
1 – 13
1–6
1–3
1 – 26
1 – 13
1 – 26
1 – 13
1 – 26
1 – 13
1 – 26
1 – 13
1 – 26
1 – 13
1 – 26
1 – 13
1–8
1–4
1–8
1–4
1–8
1–4
1 – 10
1–5
* NOTE: Refer to dimmer manufacturer's documentation for installation instructions and circuit details.
DIML3
2 WIRE PHASE DIMMING
FIXTURE
DIMMER: 2 WIRE PHASE
(BY OTHERS)
LED
LINE
SWITCHED HOT
NEUTRAL
GROUND
BLACK
WHITE
DRIVER
V+
RED
V-
BLACK
GREEN
GND
ONLY FOR SWITCHES WITH NEUTRAL
NEUTRAL
USAI
Lighting
®
www.usailighting.com
info@usailighting.com
1126 River Road
New Windsor, NY 12553
T 845–565–8500
F 845–561–1130
© 2016. USAI, LLC.
All rights reserved.
All designs protected by copyright.
I2-264-3 Revised 02/15/2016
DIMMING DRIVER COMPATIBILITY
SELECTION GUIDE
DIML4
®
USAI
Lighting
DIMMING DRIVER WIRING SCHEMES:
NOTES:
Wiring diagrams are examples of typical installations intended to illustrate the number of wires that must be run to fixture. These diagrams are
not intended to specify all equipment necessary for a given dimming circuit. Refer to specific dimmer manufacturer's documentation for details.
IMPORTANT SAFETY INSTRUCTIONS
- SAVE THESE INSTRUCTIONS
1. Keep these instructions in a safe place for future reference.
2. Only qualified electricians in accordance to local codes should install these fixtures.
3. De-energize the electrical circuit at the circuit breaker prior to installation process or servicing.
4. Make sure all connections are in accordance with the National Electrical Code and any local regulations.
5. Cap any wires not used separately (not together).
DIML4 LED: Lutron Hi-Lume A-Series LED Driver with 3-Wire FL Control / LED Dimming Driver Wiring (Dims down to 1%)
DIML4 3-Wire Dimmer Compatibility Chart
Manufacturer
120V Only
ETC
ETC
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
277V Only
ETC
ETC
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Lutron
Product
Part Number
Dimmed Light
Output Range
Sensor+ Cabinet
Unison DRd Cabinet
Nova T
Nova T
Nova
Nova
Vareo
Skylark
Diva
Ariadni
Vierti
Maestro
Maestro Wireless
RadioRA 2
HomeWorks QS
Interfaces
GP Dimming Panels
D20 Dimming module
D20F Dimming module
NTF-10NTF-103PNF-10NF-103PVF-10SF-10P-, SF-103PDVF-103P-, DVSCF-103PAYF-103PVTF-6AMAF-6AM-, MSCF-6AMMRF2-F6AN-DVRRD-F6AN-DVHQRD-F6AN-DV
PHPM-3F-120, PHPM-3F-DV
Various
100% - 1%
100% - 1%
100%–1%
100%–1%
100%–1%
100%–1%
100%–1%
100%–1%
100%–1%
100%–1%
100%–1%
100%–1%
100%–1%
100%–1%
100%–1%
100%–1%
100%–1%
Sensor+ Cabinet
Unison DRd Cabinet
Nova T
Nova T
Nova
Nova
Skylark
Diva
Ariadni
Vierti
Maestro
Maestro Wireless
RadioRA 2
HomeWorks QS
Interfaces
GP Dimming Panels
D20 Dimming module
D20F Dimming module
NTF-10-277NTF-103P-277NF-10-277NF-103P-277SF-12P-277-, SF-12P-277-3
DVF-103P-277-, DVSCF-103P-277AYF-103P-277VTF-6AMAF-6AM-277-, MSCF-6AM-277MRF2-F6AN-DVRRD-F6AN-DVHQRD-F6AN-DV
PHPM-3F-DV
Various
100% - 1%
100% - 1%
100%–1%
100%–1%
100%–1%
100%–1%
100%–1%
100%–1%
100%–1%
100%–1%
100%–1%
100%–1%
100%–1%
100%–1%
100%–1%
100%–1%
Qty Fixtures Per Control*
Fixture Wattage
39W and Less 40W - 80W
1–53
1–26
1–53
1–26
1–41
1 – 20
1–20
1 – 10
1–41
1 – 20
1–20
1 – 10
1–20
1 – 10
1–20
1 – 10
1–20
1 – 10
1–20
1 – 10
1–15
1–7
1–15
1–7
1–15
1–7
1–15
1–7
1–15
1–7
1–41
1 – 20
1–41
1 – 20
40W and Less 41W - 80W
1–53
1–26
1–53
1–26
1–44
1 – 22
1–33
1 – 16
1–44
1 – 22
1–33
1 – 16
1–33
1 – 16
1–33
1 – 16
1–44
1 – 22
1–33
1 – 16
1–20
1 – 10
1–33
1 – 16
1–33
1 – 16
1–33
1 – 16
1–88
1 – 44
1–88
1 – 44
* NOTE: Number of fixtures may be higher if wattage is less than maximum values shown. Refer to dimmer manufacturer's
documentation for installation instructions and circuit details.
DIML4 wiring diagrams continued on next page
USAI
Lighting
®
www.usailighting.com
info@usailighting.com
1126 River Road
New Windsor, NY 12553
T 845–565–8500
F 845–561–1130
© 2016. USAI, LLC.
All rights reserved.
All designs protected by copyright.
I2-264-4 Revised 02/15/2016
DIMMING DRIVER COMPATIBILITY
SELECTION GUIDE
DIML4 Continued
®
USAI
Lighting
DIMMING DRIVER WIRING SCHEMES:
NOTES:
Wiring diagrams are examples of typical installations intended to illustrate the number of wires that must be run to fixture. These diagrams are
not intended to specify all equipment necessary for a given dimming circuit. Refer to specific dimmer manufacturer's documentation for details.
IMPORTANT SAFETY INSTRUCTIONS
- SAVE THESE INSTRUCTIONS
1. Keep these instructions in a safe place for future reference.
2. Only qualified electricians in accordance to local codes should install these fixtures.
3. De-energize the electrical circuit at the circuit breaker prior to installation process or servicing.
4. Make sure all connections are in accordance with the National Electrical Code and any local regulations.
5. Cap any wires not used separately (not together).
DIML4 LED: Lutron Hi-Lume A-Series LED Driver with 3-Wire FL Control / LED Dimming Driver Wiring (Dims down to 1%)
DIML4
3 WIRE PHASE DIMMING
FIXTURE
DIMMER: 3 WIRE PHASE
(BY OTHERS)
CAP UNUSED
ECOSYS WIRES
DIMMED HOT
SWITCHED HOT
NEUTRAL
LINE
LED
PURPLE GRAY
PURPLE
ORANGE
BLACK
WHITE
GREEN
GROUND
DRIVER
V+
RED
V-
BLACK
GND
NEUTRAL
DIML4 LED: Lutron Hi-Lume A-Series LED Driver with EcoSystem Control / LED Dimming Driver Wiring (Dims down to 1%)
Manufacturer
120V / 277V
Lutron
Lutron
Lutron
Lutron
DIML4 EcoSystem Dimmer Compatibility Chart
Dimmed Light
Part Number
Output Range
Product
PowPak dimming module
Energi Savr Node
GRAFIK Eye QS (120V ONLY)
Quantum
RMJ-ECO32-DV-B
QSN-1ECO-S, QSN-2ECO-S
QSGRJ-_E, QSGR-_E
Various
100%–1%
100%–1%
100%–1%
100%–1%
Qty Fixtures Per Control*
Fixture Wattage
39W and Less 40W - 80W
1–32
1 – 16
1–64
1 – 32
1–64
1 – 32
1–64
1 – 32
* NOTE: Number of fixtures may be higher if wattage is less than maximum values shown. Refer to dimmer manufacturer's
documentation for installation instructions and circuit details.
DIML4
EcoSystem CONTROLS
ECOSYS BUS
E2
E1
E2
FIXTURE
E1
WALL CONTROL
(BY OTHERS)
LINE
NEUTRAL
CAP
UN-USED
ORANGE
WIRE
PURPLE GRAY
PURPLE
ORANGE
BLACK
WHITE
GREEN
LED
DRIVER
V+
RED
V-
BLACK
GND
USAI
Lighting
®
www.usailighting.com
info@usailighting.com
1126 River Road
New Windsor, NY 12553
T 845–565–8500
F 845–561–1130
© 2016. USAI, LLC.
All rights reserved.
All designs protected by copyright.
I2-264-4 Revised 02/15/2016
DIMMING DRIVER COMPATIBILITY
SELECTION GUIDE
DIML6A, 6E
DIML6B, 6F
®
USAI
Lighting
IMPORTANT SAFETY INSTRUCTIONS
- SAVE THESE INSTRUCTIONS
1. Keep these instructions in a safe place for future reference.
2. Only qualified electricians in accordance to local codes should install these fixtures.
3. De-energize the electrical circuit at the circuit breaker prior to installation process or servicing.
4. Make sure all connections are in accordance with the National Electrical Code and any local regulations.
5. Cap any wires not used separately (not together).
DIML6A and DIML6E LED Dimming Compatibility Table
DIML6A and DIML6E are linearly programmed dimming drivers for use with logarithmic-style dimming controls (e.g., Lutron and others listed in the table below)
DIML6A = EldoLED SOLOdrive 0-10V control dims from 100% to 0.1%
DIML6E = EldoLED ECOdrive 0-10V control dims from 100% to 1%
Dimmed Light Qty Fixtures
Manufacturer Product
Part Number
Output Range Per Dimmer*
Refer to manufacturer's
120V & 277V
DIML6A / E
Lutron
Diva
DVTV/NFTV/NTFTV with PP-20
99% - 0.1% / 1% dimmer load rating for
Lutron
Energi Savr Node
QSN-4T16-S
100% - 0.1% / 1% maximum and minimum
Lutron
GP Dimming Panels TVM2 Module
99% - 0.1% / 1% fixture quantities per
Lutron
Interfaces
GRX-TVI w/ GRX3503
100% - 0.1% / 1% dimmer.
Sensor Switch nIO
nIO EZ
100% - 0.1% / 1%
* NOTE: Refer to dimmer manufacturer's documentation for installation instructions and circuit details.
DIML6B and DIML6F LED Dimming Compatibility Table
DIML6B and DIML6F are logarithmic-programmed dimming drivers for use with linear-style dimming controls (e.g., Crestron, non-Lutron and others listed in the table below)
DIML6B = EldoLED SOLOdrive 0-10V control dims from 100% to 0.1%
DIMMER: 0-10V
DIML6F = EldoLED ECOdrive
(BY OTHERS) 0-10V control dims from 100% to 1%
0-10V (-)
GRAY
0-10V (+)
PURPLE
LED
DIML6B Dimmer Compatibility Chart
Dimmed Light
Qty Fixtures
V+
RED
SWITCHED HOT
SWITCHED
HOTNumber DRIVER
Manufacturer
Product
Part
Output Range
Per Dimmer*
VBLACK
NEUTRAL
WHITE
Refer to
120V & 277V
DIML6B / F
GREEN 2112U-101
Bush-Jaeger
Electronic potentiometer
100% - 0.1% / 1% manufacturer's
Jung
Electronic potentiometer
100% - 0.1% / 1% dimmer load
GND 240-10
CLASS 2 CONTROL WIRES
Leviton
IllumaTech dimmer
IP710-DLX
100% - 0.1% / 1% rating for
LINE
Lightolier
(Philips) Momentum (120V ONLY)
ZP600FAM120
100% - 0.1% / 1% maximum and
RELAY
Merten
Electronic
potentiometer
5729
100% - 0.1% / 1% minimum fixture
(BY OTHERS)
DIML6A,
6B
Pass & Seymour Titan
CD4FB-W
100% - 0.1% / 1% quantities per
NEUTRAL
TO SWITCH POWER
Watt Stopper
Miro 0-10V DIMMING W/RELAY
DCLV1
100% - 0.1% / 1% dimmer.
Synergy
Wallbox Dimmers
ISD BC
100% - 0.1% / 1%
ABB
i-bus
SD/S 2.16.1
100% - 0.1% / 1%
Crestron
Modules
GLX-DIMFLV8, GLXP-DIMFLV8
100% - 0.1% / 1%
Crestron
Green Light
GLPAC-DIMFLV4-, GLPAC-DIMFLV8100% - 0.1% / 1%
DIML6A, 6B
0-10V (-)
Crestron
Green Light Power Pack
GLPP-DIMFLVEX-PM, GLPP-1DIMFLV2EX-PM,
GLPP-1DIMFLV3EX-PM
100% - 0.1% /FIXTURE
1%
0-10V DIMMING
W/RELAY TO GRAY
SWITCH POWER
0-10V (+)
PURPLE
DIMMER: 0-10V
Crestron
DIN Rail Analog Output Module
DIN-A08
100% - 0.1% / 1% V+ RED
SWITCHED HOT
BLACK
Crestron
DIN Rail 0-10V Fluorescent Dimmer
DIN-4DIMFLV4
100% - 0.1% / 1% LEDV- BLACK
NEUTRAL
WHITE
GREEN
Crestron
iLux 0-10V Dimmer Expansion Module CLS-EXP-DIMFLV
100% - 0.1% / 1%
DRIVER
GND
* NOTE: Refer to dimmer manufacturer's documentation for installation instructions andCLASS
circuit
details.
2 CONTROL WIRES
(BY OTHERS)
LINE
DIMMING DRIVER WIRING SCHEMES:
RELAY
(BY OTHERS)
NOTES:
NEUTRAL
Wiring diagrams are examples of typical installations intended to illustrate the number of wires that must be run to fixture. These diagrams are
not intended to specify all equipment necessary for a given dimming circuit. Refer to specific dimmer manufacturer's documentation for details.
DIML6
0-10V DIMMING (NO RELAY)
DIML6
0-10V DIMMING W/RELAY TO SWITCH POWER
FIXTURE
(BY OTHERS)
0-10V (-)
GRAY
0-10V (+)
PURPLE
SWITCHED HOT
BLACK
NEUTRAL
WHITE
(BY OTHERS)
LED
DRIVER
V+
RED
V-
BLACK
LINE
GREEN
GROUND
GND
0-10V (-)
GRAY
0-10V (+)
PURPLE
SWITCHED HOT
BLACK
NEUTRAL
WHITE
LED
DRIVER
V+
RED
V-
BLACK
GREEN
GND
CLASS 2 CONTROL WIRES
LINE
FIXTURE
DIMMER: 0-10V w/
POWER SWITCHING
DIMMER: 0-10V
RELAY
(BY OTHERS)
NEUTRAL
NEUTRAL
USAI
Lighting
®
www.usailighting.com
DIML6A, 6B
info@usailighting.com
1126 River Road
New Windsor, NY 12553
0-10V DIMMING (NO RELAY)
DIMMER: 0-10V w/
POWER SWITCHING
(BY OTHERS)
FIXTURE
T 845–565–8500
F 845–561–1130
© 2016. USAI, LLC.
All rights reserved.
All designs protected by copyright.
I2-264-6 Revised 05/20/2016
DIMMING DRIVER COMPATIBILITY
SELECTION GUIDE
DIML7
®
USAI
Lighting
DIMMING DRIVER WIRING SCHEMES:
NOTES:
Wiring diagrams are examples of typical installations intended to illustrate the number of wires that must be run to fixture. These diagrams are
not intended to specify all equipment necessary for a given dimming circuit. Refer to specific dimmer manufacturer's documentation for details.
IMPORTANT SAFETY INSTRUCTIONS
- SAVE THESE INSTRUCTIONS
1. Keep these instructions in a safe place for future reference.
2. Only qualified electricians in accordance to local codes should install these fixtures.
3. De-energize the electrical circuit at the circuit breaker prior to installation process or servicing.
4. Make sure all connections are in accordance with the National Electrical Code and any local regulations.
5. Cap any wires not used separately (not together).
DIML7 LED: EldoLED DALI Dimming Driver Wiring (Dims down to 0.1%)
DIML7
DALI CONTROLS
DALI BUS
DA
DA
FIXTURE
WALL CONTROL
(BY OTHERS)
LINE
NEUTRAL
LED
ORANGE (-)
ORANGE/WHITE (+)
BLACK
WHITE
GREEN
DRIVER
V+
RED
V-
BLACK
GND
USAI
Lighting
®
www.usailighting.com
info@usailighting.com
1126 River Road
New Windsor, NY 12553
T 845–565–8500
F 845–561–1130
© 2016. USAI, LLC.
All rights reserved.
All designs protected by copyright.
I2-264-7 Revised 02/15/2016
DIMMING DRIVER COMPATIBILITY
SELECTION GUIDE
DIML9
®
USAI
Lighting
DIMMING DRIVER WIRING SCHEMES:
NOTES:
Wiring diagrams are examples of typical installations intended to illustrate the number of wires that must be run to fixture. These diagrams are
not intended to specify all equipment necessary for a given dimming circuit. Refer to specific dimmer manufacturer's documentation for details.
IMPORTANT SAFETY INSTRUCTIONS
- SAVE THESE INSTRUCTIONS
1. Keep these instructions in a safe place for future reference.
2. Only qualified electricians in accordance to local codes should install these fixtures.
3. De-energize the electrical circuit at the circuit breaker prior to installation process or servicing.
4. Make sure all connections are in accordance with the National Electrical Code and any local regulations.
5. Cap any wires not used separately (not together).
DIML9 LED: TRIAC Forward Phase Dimming Driver Wiring (Dims down to 15%) 120V Only
DIML9
2 WIRE PHASE DIMMING
FIXTURE
DIMMER: 2 WIRE PHASE
(BY OTHERS)
LED
LINE
SWITCHED HOT
NEUTRAL
GROUND
BLACK
WHITE
DRIVER
V+
RED
V-
BLACK
GREEN
GND
ONLY FOR SWITCHES WITH NEUTRAL
NEUTRAL
USAI
Lighting
®
www.usailighting.com
info@usailighting.com
1126 River Road
New Windsor, NY 12553
T 845–565–8500
F 845–561–1130
© 2016. USAI, LLC.
All rights reserved.
All designs protected by copyright.
I2-264-9 Revised 02/15/2016
DIMMING DRIVER COMPATIBILITY
SELECTION GUIDE
DIML10
®
USAI
Lighting
DIMMING DRIVER WIRING SCHEMES:
NOTES:
Wiring diagrams are examples of typical installations intended to illustrate the number of wires that must be run to fixture. These diagrams are
not intended to specify all equipment necessary for a given dimming circuit. Refer to specific dimmer manufacturer's documentation for details.
IMPORTANT SAFETY INSTRUCTIONS
- SAVE THESE INSTRUCTIONS
1. Keep these instructions in a safe place for future reference.
2. Only qualified electricians in accordance to local codes should install these fixtures.
3. De-energize the electrical circuit at the circuit breaker prior to installation process or servicing.
4. Make sure all connections are in accordance with the National Electrical Code and any local regulations.
5. Cap any wires not used separately (not together).
DIML10 LED: ELV Reverse Phase Dimming Driver Wiring (Dims down to 15%) 120V Only
DIML10
2 WIRE PHASE DIMMING
FIXTURE
DIMMER: 2 WIRE PHASE
(BY OTHERS)
LED
LINE
SWITCHED HOT
NEUTRAL
GROUND
BLACK
WHITE
DRIVER
V+
RED
V-
BLACK
GREEN
GND
ONLY FOR SWITCHES WITH NEUTRAL
NEUTRAL
USAI
Lighting
®
www.usailighting.com
info@usailighting.com
1126 River Road
New Windsor, NY 12553
T 845–565–8500
F 845–561–1130
© 2016. USAI, LLC.
All rights reserved.
All designs protected by copyright.
I2-264-10 Revised 02/15/2016