Motion Sensing Luminaires
For Stairwells And Other Public Spaces
High Abuse
Occupancy Sensor
Lighting Products
HA
2 Energy Saving Solutions – Occupancy Sensor Lighting Products
As maintenance and operational expenses escalate, facility managers
and building owners are continuously challenged to find ways of
reducing costs by controlling energy. Public and vehicular traffic
areas must have adequate light levels for proper safety and
ingress/egress. Lighting in intermittently occupied areas, when
properly controlled, poses the greatest potential for cost savings
without sacrificing safety or performance. Many states have enacted
energy saving code requirements that mandate the use of occupancy
control for lighting.
Specifications
For optimum luminaire control and flexibility, Kenall uses the
Watt Stopper ® FM-105 super high-frequency occupancy sensor
(and /or equivalent) as an integral feature. In addition to its sensitivity
and available control options, the component also features
daylighting control that provides additional savings when the sensor
detects ambient light levels greater than its daylighting set-point.
Kenall offers a line of Wet Location and IP certified products for
use with occupancy sensors in applications where energy saving
potential is substantial. Since the motion sensor is placed behind the
lens, the luminaire is able to maintain its aesthetic appeal, IP rating
and Kenall's Peace of Mind Guarantee®. This application guide has
been developed to provide fixture and sensor details, installation tips
and product solutions for the greatest energy savings.
Kenall offers a wide assortment of luminaires with an integral occupancy sensor
that provides facility managers and building owners energy saving solutions to a
variety of applications with intermittent traffic.
www. kenall.com
P: 800-4-Kenall
F: 847-360-1781
1020 Lakeside Drive Gurnee, Illinois 60031
The Kenall product shown on this page is manufactured in the USA with components purchased from US suppliers, and meets the Buy American
requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof.
3
Installation Guide
Energy saving solution products from Kenall are perfect in enclosed stairwells, corridors, entry and exit points and parking garages.
To maximize energy savings, special attention should be given to luminaire location in relation to unintended objects that could trigger
a false fixture activation such as windows, nearby moving plants, pedestrians or traffic passing by (see illustrations below).
Recommended application
Good applications
No exterior windows in corridors or stairwells that
nearby pedestrian or vehicular traffic may cause a
false triggering of the fixture. An enclosed corridor or
stairwell with a source for daylight can also provide
optimum use of the daylight hold-off feature.
Non-recommended application
Luminaires with occupancy sensors that are
installed too close to windows can result in
sporadic false activation of the fixtures
Applications with possible issues
Luminaires with occupancy sensors that are installed
too close to exterior windows or unintended objects
can result in sporadic false activation of the fixtures,
reduced energy savings and a premature reduction
of lamp life. Outside traffic, pedestrians and swaying
trees can cause the luminaire to stay on.
www. kenall.com
P: 800-4-Kenall
F: 847-360-1781
1020 Lakeside Drive Gurnee, Illinois 60031
The Kenall product shown on this page is manufactured in the USA with components purchased from US suppliers, and meets the Buy American
requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof.
4
Sensor Features
Flexible Functionality
Operation
The FM-105 sensor coverage pattern is omnidirectional. Depending
on the installation, it can be adjusted to detect occupancy up to
20 feet away. The sensor is installed inside the luminaire so that
it is completely hidden from direct view. Its integrated daylight
sensitivity adjusts from 2 to 200 footcandles and its time delay may
be set from 10 seconds to 30 minutes.
The sensor operates at 120 or 277 VAC and utilizes SHF
technology to control lighting based on occupancy. It sends out
electromagnetic waves that bounce off nearby surfaces and uses
the Doppler principle to analyze changes in the return waves to
detect motion in the area (similar to the way that ultrasonic sensor
technology performs).
When motion is detected, the sensor turns on the load, unless
the ambient light level is greater than the daylighting setpoint
(if enabled), or turns off the load when no motion is detected for
the preset time delay.
Adjustable time delay
Adjustable detection sensitivity
Hold-off daylighting control
Sensor Coverage Area Ceiling Mount
Sensor Coverage Area Wall Mount
18'
18'
12'
6'
12'
Sensor
inside
ceiling mount
fixture
at 8'
height
MIN. 3'
MAX. 20'
6'
MAX.
MIN.
0
Control Adjustments
Time delay – The sensor automatically turns off the light after
the coverage area has been vacant for the selected time delay. For
high traffic areas, the time delay should be set close to minimum
levels. Low traffic areas, to maximum energy savings, the time delay
should be set closer to the maximum settings. The sensor provides
a 10 second to 30 minute range of adjustability.
Sensitivity – The sensor has a range of 0 to 20 feet. It is able to
sense through solid objects, glass and dense materials. Once
the sensitivity is set to the desired level, the luminaire should
be tested to determine if the sensor detects movement
correctly. The sensor setting can be adjusted up or down for
the correct application.
Light Level – Adjust the daylight setting if the installation
has sufficient ambient light in the area to keep the lights and
luminaire off. Set the time delay to minimum and then adjust the
daylight setting to the appropriate level. The daylight setting can
be adjusted up or down (2 to 200 footcandles) for the correct
application with separate adjustment to the time delay setting.
Note: The sensor’s daylight hold-off feature will override the
sensitivity control setting, keeping the fixture off, if sufficient
ambient daylight is present.
WattStopper® is a registered trademark of Legrand®.
www. kenall.com
P: 800-4-Kenall
F: 847-360-1781
1020 Lakeside Drive Gurnee, Illinois 60031
The Kenall product shown on this page is manufactured in the USA with components purchased from US suppliers, and meets the Buy American
requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof.
Occupancy Sensor Lighting Products
5
The following Architectural High Abuse and Rough Service products are available with an intergral occupancy sensor.
For complete product specifications, go to www.kenall.com. For applications that call for custom products, please contact our
Applications Department at 800-4-Kenall.
EnviroSeal™
Nova II™
Nominal 5"× 48"
ES548MS Series
with occupancy sensor
Ceiling/Wall Mount
Lamps: T5, T8
Nominal 10"× 48"
N1048MS Series (7200)
with occupancy sensor
Ceiling Mount
Lamps: Biax, T5, T8
IP65
Wet Locations
ADA
Optional
Wet Locations
Millenium Stretch™
Sheriff™
Nominal 12"× 24"
MLHA1224MS Series
with occupancy sensor
Individual Luminaires
Ceiling/Wall/Corner Mount
Lamps: T5, T8
Nominal 5"× 24"
SH524MS Series
with occupancy sensor
Ceiling / Wall Mount
Lamps: T5, T8
ADA
IP64
ADA
Wet Locations
Wet Locations
Millenium Stretch™
Sheriff™
Nominal 12"× 48"
MLHA1248MS Series
with occupancy sensor
Individual Luminaires
Ceiling/ Wall/Corner Mount
Lamps: T5, T8
Nominal 5"× 48"
SH548MS Series
with occupancy sensor
Ceiling / Wall Mount
Lamps: T5, T8
ADA
IP64
ADA
Wet Locations
Wet Locations
Millenium™ Round
Kenall’s High Abuse
luminaires are designed and
built to take exceptional
physical punishment. When
installed according to our
instructions, Kenall will
repair or replace any fixture
rendered inoperable due to
physical abuse for the life of
the product installation.
Nominal 17" Dia. × 6"
MR17FLMS Series
with occupancy sensor
17" Round Full Face
Ceiling / Wall Mount
Lamps: CFL
IP64
Wet Locations
www. kenall.com
P: 800-4-Kenall
F: 847-360-1781
1020 Lakeside Drive Gurnee, Illinois 60031
The Kenall product shown on this page is manufactured in the USA with components purchased from US suppliers, and meets the Buy American
requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof.
1020 Lakeside Drive
Gurnee, Illinois 60031
847-360-8200
FAX 847-360-1781
www.kenall.com
©2011 Kenall Mfg. Co.
All rights reserved.
L10035-030811