PAGEL-INDUSTRIAL FLOOR
®
P R O P E RT I E S
F I E L D S O F A P P L I C AT I O N
• ready for use, cementitious industrial floor cementitious hard aggregate floor screed for
use as a hard composite topping for medium
use as specified for stress group:
Medium (DIN18560 part 7)
• industrial floors subject to heavy-duty use
• certified to fire protection class A1 as
specified by EN 13501 and DIN 4102
P40
• storage areas in waste incineration plants
P80
• warehouses, production facilities
• repair workshops, indoor car parking areas,
vehicle scales
• engineering and automotive industry
• bonds well to solid substrates
• production and conveyor lines
• highly wear resistant
• exhibition halls
• impermeable to water and largely resistant
to oils and fuels
• supermarkets & hypermarkets
• open public spaces
• dense surface structure and highly resistant
to frost and deicing salt
• easy to apply and cost-effective
• non-skid and waterproof
• supplied ready for use, just mix with water
• easy to clean, dirt does not penetrate surface
• high-quality, natural and hard aggregates –
for high durability and a long service life
• hard aggregate class A (DIN 1100)
Exposure class according to:
DIN 1045-2 and EN 206-1
PAGEL – INDUSTRIAL FLOOR
XO
0
• company is certified according
DIN EN ISO 9001:2008
P40
P80
GROUTS
SPECIAL AND
ANCHOR GROUT
SEWER
REHABILITATION
CONCRETE
REPAIRING
READY-FOR-USE
MORTAR
•
•
XC
1234
XS
123
XF
1234
XA
123
XM
123
•••• ••• •••
•••• ••• •••
••••
••••
••
••
••
••
CHANNEL
MORTAR
XD
123
CONCRETE
PROTECTION
INDUSTRIAL
FLOOR
CONSTRUCTION
PRODUCTS
RESINS
PAGEL®-INDUSTRIAL FLOOR
P40
T E C H N I C A L D ATA
A P P L I C AT I O N
TYPE
P80
grain size
amount of water
working time
P40
P80
mm
0-4
0-8
%
8
8
min. app. 45 app. 45
consumption
for 10 mm-thick layer
kg/m2
23
23
mm
10–40
30–80
cm
7.9
8.2
coating thickness
abrasion (Böhme) on 50 cm
2
3
hard aggregate group (DIN 1100)
A
A
1d
N/mm2
욷 50
욷 50
7d
N/mm2
욷 70
욷 70
28 d
N/mm2
욷 90
욷 90
1d
N/mm2
욷5
욷5
7d
N/mm2
욷 10
욷 10
28 d
N/mm2
욷 14
욷 14
adhesive tensile strength 7 d
N/mm2
욷 1.5
욷 1.5
fresh mortar density
kg/dm3
2.4
2.45
compressive strength*
bending strength
e-modul (static)
7d
N/mm2 39,700 41,500
28 d
N/mm2 43,100 44,600
All test data are guide values, proofed in our German manufacturing plants,
- values from other manufacturing plants may vary.
* DIN EN 196-1-compliant compressive strength testing
storage:
12 months. Cool, dry, free from frost.
Unopened in its original packaging.
packaging: 20-kg-bag, euro-pallet 960 kg
hazard class: no dangerous substance follow
safety data sheet
SUBSTRATE: Clean thoroughly, remove loose and unsound
material as well as cement slurries using sand, shot or water
jet blasting or similar until the underlying grain structure has
been exposed. The substrate must have adequate bond
strength (욷1.5 N/mm2, on average).
Remove all rust from the exposed reinforcing concrete bars
(puriy grade Sa2 to Sa2 1/2) and coat with MS 02 PAGELCORROSION PROTECTION without leaving any gaps.
Any cracks inside the concrete substrate must be soaked and
sealed or grouted. Finish by removing any surface impurities
originating from the crack filling. The (concrete) substrate to
be coated must not be subject to the development of any
cracks. The repaired surface areas must be cut back 10 mm
at the edges.
Mineral-based Adhesion Layer: PH 10 PAGEL
INDUSTRIAL FLOOR-ADHESION LAYER
Pre-wet to saturation (approx. 6 – 24 hours). Brush deep into
the pores of the ready-prepared substrate using a hard brush.
Apply floor screed wet-on-wet.
Epoxy resin primer: EH1 PAGEL – EPOXY RESIN
The substrate must be dry. The concrete’s surface moisture
content must be less than 4 %; the substrate’s temperature
must be at least 10 °C. The substrate’s temperature must be
at least 3 °C above the prevailing dew point temperature.
The substrate to be coated must be protected against rising
damp before priming.
MIXING: The grout is supplied ready for use and only needs
to be mixed with water. Add all of the water, with exception of
a small residual amount, into the compulsory mixer, add the
dry mortar and mix for approx. 3 minutes. Add the remaining
water and mix for another 2 minutes.
APPLICATION: Lay wet-on-wet before the adhesion layer
has set using conventional tools. To finish, smoothen surface
using a compacting trowel or power trowel.
FINISHING TREATMENT: Protect surface from wind, draughts
and premature water evaporation using, e.g. jute sheets,
sheeting or EH136 PAGEL RESIN. The additional
information provided in the technical data sheet for
O1 PAGEL EVAPORATION PROTECTION or
EH136 PAGEL RESIN must also be observed if used
in low temperatures, if exposed to direct sunlight or wind.
Please contact our customer service department in the event
the floor will be exposed to frost when being laid.
Min/max. temperature for application: ѿ5 oC up to ѿ35 oC
Technical Ref. Sheet 1411 GB
QS-Formblatt 11/13 Rev. 06
The information provided in this leaflet, is supplied by our consulting
service and is the end result of exhaustive research work and extensive experience. They are, however, without liability on our part, in
particular with regard to third parties proprietary rights, and do not
relieve the user of the responsibility for verifying that the products
and processes are suitable for the intended application. The data
presented was derived from tests under normal climate conditions
according to DIN 50014 and mean average values and analysis. Deviations are possible when delivery takes place. Given that recommendations may differ from those shown in this leaflet written confirmation should be sought. It is the responsibility of the purchaser
to ensure they have the latest leaflet issue and that its contents are
current. Our customer service staff will be glad to provide assistance at any time. We appreciate the interest you have shown in our
products. This technical data sheet supercedes previously issued
information. Please find the latest leaflet issues at www.pagel.com.
SPEZIAL - BETON GMBH & CO.KG
WOLFSBANKRING 9 · 45355 ESSEN · GERMANY
TEL. ѿ49 201 68504 - 0 · FAX ѿ49 201 68504 - 31
INTERNET WWW.PAGEL.COM · E-MAIL INFO@PAGEL.COM