INSTALLATION GUIDE FOR WALL
MOUNT KITS WB-6300/6600/6800
Rev. : Original
KIT NAME: WB-6300 or WB-6600 or WB-6800
KIT CONTENT (Besides this guide):2
WB-6300 or WB-6600 or WB-6800 wall mount bracket
with back cover - - - - - - - 1 set
Self tapping screw 4φ-16L (P/N: 10641040162) - - - - - - - - - - 4 pcs
Plastic cotter (P/N: 10241000021) - - - - - - - - - - - - - - - - - - - 4 pcs
This guide - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 copy
KIT APPLICATION: This kit is applicable to all TP & KS & 15” TM series
DRILLING PATTERN
9.75” or 248 mm
5.5” or 140 mm
INSTALLATION PROCEDURES
A. WALL MOUNTING:
WB-6300
P/N: 16200902010
WB-6600
1
WB-6800
1. Select a flat surface on wall of adequate strength and with proper ventilation
and space condition. Unfold the attached paper template for drill pattern on
the wall surface in correct orientation. Drill 4 holes in rectangular layout as
marked in the template that gives a rectangular drill pattern of 9.75” or 248
mm wide (horizontal) and 5.5” or 140 mm high (vertical). Hole diameter
should be 1/4” or 6.35 mm each. Hole depth should be at least 1 and 3/8” or
35 mm. Please then insert one plastic cotter into each hole leaving the flat
end with hole of the plastic cotter at the outside opening of the hole. Use a
hammer to tap the plastic cotter in gently if necessary.
2. Please separate the back cover of the wall mount bracket kit and fix it to wall
at the 4 arrowed holes as appropriate according to these pictures below per
type of back covers with proper materials and proper preparations. Install
required optional device kits with their mechanical fixation parts in the wall
mount bracket (as described later) and hang the backpack to the back cover
that is already fixed on wall with the cables coming out of the brackets
through the openings marked with rectangles in the above pictures. Screw
lock the top side of the backpack.
WB-6300
WB-6600
WB-6800
3. Align the four matching pegs on the back of the main
unit as circled in the left picture with the four
matching holes in the wall mount brackets as also
marked in circles in the top pictures and allow the
main unit to slide down the winding grooves in the
wall mount backpack. Connect all cables coming out of
the backpack into the cable cover area of main unit.
The area required for wall mount application is determined
by the main unit dimensions and is 378 mm in width and
312 mm in height for TP/KS/TM series with 15” touch
panel and is 426 mm in width and 370 mm in height for KS series with 17”
touch panel.
Wall Mount Kit Guide
2
B. OPTIONAL DEVICE KITS:
1. UPS battery:
for WB-6300
for WB-6600
for WB-6800
For installing the UPS battery in WB-6300 and WB-6600, insert the
Velcro strap through the 2 slits in the bracket as shown in the 2 left pictures
above and hold the battery with the Velcro strap. For WB-6800, first separate
the UPS battery bracket and the screw from the bracket as in upper right picture.
Slide the bracket up with its tongue matching under a bridge in the wall of wall
mount bracket with the UPS battery in place and fix it with the screw as arrowed
in the above right picture.
2. 2.5” HDD Kit:
To install the 2.5” HDD in WB-6300 & WB-6800, a proper cable set
including cables and a proper conversion board is required separately. Remove
the 2.5” HDD bracket from the wall mount bracket and prepare for the preassembly operation of the 2.5” HDD bracket with screws and the cable set as in
the leftmost picture above. Please use 2 screws to fix the conversion board to
one end of the HDD bracket as in the middle picture above and insert the HDD
cable and the HDD power cable in the connectors on conversion board as in the
rightmost picture above. Please make sure that the cables are inserted in correct
orientation. Leave the pull strap end of IDE HDD cable for connection to main
unit. Then please remove the screw fixing the HDD bracket cover on the other
end of the bracket if it is preinstalled.
Wall Mount Kit Guide
3
In WB-6300
In WB-6800
Refer to the 1st row of pictures above for WB-6300 and 2nd row for WB6800 to install the 2.5” HDD bracket into the wall mount bracket. Check in the
lower left part of WB-6300 and lower right part of WB-6800 for the 3 metal
posts as circled and 2 support lugs with notches as arrowed in the leftmost
pictures. Place edge of the conversion board in the notches and pull back the
HDD bracket cover to open it and screw the HDD bracket to the posts as in the
2nd left pictures. Put the 2.5” HDD into the HDD bracket with orientation as in
the 2nd right pictures and slide the HDD to the bracket cover joint as shown.
Close the cover and push the cover with HDD to the direction in the rightmost
pictures firmly then screw at the circled point in same pictures. Route cables to
exit the wall mount bracket through the correct opening.
3. 3.5” HDD:
To install the 3.5” HDD in WB-6600, the required 3.5” HDD bracket, 4
rubber sleeves, 4 shoulder screws and a bracket fixing screw are included in
WB-6600 however the HDD cable and HDD power cable need to be prepared
Wall Mount Kit Guide
4
separately and these are presented as in the left picture above. Slide rubber
sleeves into screw holes in bracket to have the bracket clips into the middle
groove of rubber sleeve as arrowed in left picture above. Put HDD in place
inside the bracket with the HDD control board facing the bracket and the HDD
connectors then fix shoulder screws as in the middle picture above. Then please
insert the 2 arrowed lugs of HDD bracket in middle picture above into 2 arrowed
slits in wall mount bracket in right picture above and screw fix the HDD bracket
at the circled post.
Then connect the HDD cable and the HDD
power cable to the 3.5” HDD. Please make sure
the cables are inserted in correct orientation.
Leave the pull strap end of IDE HDD cable for
connection to main unit. Route cables to exit the
wall mount bracket through the correct opening
as in the right picture here.
3.5” HDD in WB-6600
4. 80W Power Adaptor Kit (in WB-6800 only)
To install the 80W power adaptor in WB-6800, an 80W power adaptor
bracket and 2 screws besides the 80W power adaptor are required as in the left
picture below. Please insert the power adaptor from the right side of the bracket
in the way shown in top of middle picture below and insert the arrowed 2 lugs on
power adaptor bracket into the arrowed 2 slits in wall mount bracket. Fix the
power adaptor bracket to wall mount bracket with screws at 2 circled positions
and exit the cable through the correct opening in wall mount bracket as in the
right picture below.
Wall Mount Kit Guide
5
5. CDROM Kit (in WB-6800 only)
To install the CDROM/COMBO drive in WB-6800, a CDROM bracket, 4
small CDROM drive fixing screws, 1 CDROM bracket fixing screw, a 3
connector IDE cable and a 3 connector HDD power cable as in the left picture
below are required in addition to the CDROM/COMBO drive itself. It is
advisable to install the CDROM/COMBO drive before the HDD assembly for
easier operation. Fix the CDROM drive tightly into the CDROM bracket with 4
small screws at the red arrowed positions in the middle pictures. The top and
bottom small pictures are the side views for the screw positions. Install the
CDROM with bracket in the wall mount bracket by making sure that the
CDROM bracket slides into the blue arrowed slit in the middle picture below.
Please use the left hole of the 2 screw holes on CDROM bracket rectangular
marked in the left picture to have the exterior of CDROM drive flat with the wall
mount bracket. Connect the red arrowed connectors of IDE data and power cable
to the CDROM drive. Exit the blue arrowed connectors through the correct
opening in wall mount bracket and leave the rest for connection to the 2.5” HDD
as in the right picture below.
Wall Mount Kit Guide
6
Template for WB-6300
THIS SIDE UP
Each hole should
be at least 1 + 3/8”
or 35 mm deep.
Drill at center of
dashed cross
Drill at center of
dashed cross
Wall Mount Kit Guide
Use drill tip of
diameter 1/4” or
6.25 mm.
Drill at center of
dashed cross
Drill at center of
dashed cross
7
Template for WB-6600
THIS SIDE UP
Drill at center of
dashed cross
Drill at center of
dashed cross
Use drill tip of
diameter 1/4” or
6.25 mm.
Each hole should
be at least 1 + 3/8”
or 35 mm deep.
Drill at center of
dashed cross
Wall Mount Kit Guide
Drill at center of
dashed cross
8
Template for WB-6800
Drill at center of
dashed cross
THIS SIDE UP
Drill at center of
dashed cross
Use drill tip of
diameter 1/4” or
6.25 mm.
Each hole should
be at least 1 + 3/8”
or 35 mm deep.
Drill at center of
dashed cross
Wall Mount Kit Guide
Drill at center of
dashed cross
9