Shelby High School
PROJECT NAME:
OE PROJECT NO.:
J20100329.000
SUBMITTAL NO:
Various
MANUFACTURER:
Auditorium Audio Equipment Data Sheets - Re-submittal
DESCRIPTION:
SPEC SECTION:
Sub #014 275122
Auditorium Audio
Equipment Data
Sheets
Resubmission
20130515
275122
DATE RECEIVED
5/16/13
DATE DUE
5/23/13
OSBORN DISTRIBUTION
Discipline
Reviewer
Review Complete Date
AMW
05/21/2013
Action
Architectural:
Structural:
Civil:
Mechanical:
Electrical:
1100 Superior Ave., #300
441 Wolf Ledges Pkwy., #300
Cleveland, OH 44114
Akron, OH 44311
t: 216-861-2020
t: 330-535-3132
f: 216-861 3329
f: 330-535-3195
X
Technology:
REV
Other:
“px” in the check box indicates the Primary Reviewer; “x” in the check box
indicates additional Reviewer(s).
2.
The Primary Reviewer should review the submittal first.
3.
The Primary Reviewer is responsible for coordinating with the other
disciplines.
1.
osborn-eng.com
This information is only for the general conformance with the design
concept and the information given in the Construction Documents.
Comments made on the shop drawings during this review do not relieve
the contractor from compliance with the requirements of the plans and
specifications and applicable laws, codes and regulations. Review of a
specific item shall not include review of an assembly of which the item is a
component. The Contractor is responsible for: dimensions to be confirmed
and correlated at the job site; information that pertains solely to the
fabrication processes or to the means, methods, techniques, sequences
and procedures of construction; coordination of the Work with that of all
other trades and performing Work in a safe and satisfactory matter.
REVIEWED FOR VALIDITY OF DESIGN
CRITERIA ONLY
REVIEWED (REV):
FURNISH AS NOTED (FN):
REVISE AND RESUBMIT (RR):
REJECTED (REJ):
SUBMIT SPECIFIED ITEM:
SUBMITTAL NOT REQUIRED
AND NOT REVIEWED:
REVIEWED BY: AMW
DATE: 6/10/2013
NO EXCEPTION TAKEN:
REVISE AND RESUBMIT
AS NOTED:
REVIEWED BY:
DATE:
Comments:
1. This is an updated submission. While additional components are in this submission, there still appears to be missing items.
One item specifically missing is the powered monitors. Please submit the missing items.
Page 1 of 2
Submittal Review Form - Standard
2. For all wireless systems, verify that antennae locations and provided quantities are sufficient to facilitate 100% coverage of
the auditorium.
3. Verify any/all owner network configuration information with Owner and NCOCC to coordinate VLAN amd IP range
assignments.
Page 2 of 2
Submittal Review Form - Standard
Submittal Stamp Page
PROJECT:
Shelby High School
CM / AE:
Barton Malow Company, MKC Associates & Obsorn Engineering
CONTRACTOR:
Zenith Systems LLC
Submittal Type Attached:
Architectural
X
Structural, Mechanical, Electrical
SUBMITTAL NO:
Samples
DATE:
2
ITEM(S): Auditorium Audio Equipment Data Sheets
SPECIFICATION SECTION(S):
Shop Drawings
QUANTITY:
27 51 22
CONTRACTOR STAMP
By Stacie Steele at 4:38 pm, May 15, 2013
CM STAMP
A/E STAMP
5/14/2013
1
PROJECT SUBMITTALS
Shelby Schools
High School Technology
Item
#
SEC/
ITEM
DESCRIPTION
MNFG
PARTNUMBER
1
275122
CD/IpodPlayer
TASCAM
CD200i
2
275122
DigitalAudioRecorder
TASCAM
CDRW900SL
3
275122
HangingMicrophone
AKG
CHM99(Black)
4
275122
XLRMicCables(25'&50')
ProCo
AQ25&AQ50
5
275122
MixingConsole
Yamaha
LS916
6
275122
WirelessMicrophone
Shure
ULXP1430
7
275122
WirelessMicAntennaCombiner
Shure
UA844SWB
8
275122
HearingAssist
Williams
PPA377PRO
9
275122
HearingAssistReceiver
Williams
PPAR37
10
275122
HearingAssistNeckloop
Williams
NKL001
11
275122
HearingAssistEarBud
Williams
EAR014
12
275122
HearingAssistChargingBase
Williams
CHG3512
13
275122
Powerconditioner/sequencer
Furman
PS8RII
14
275122
Amplifier
Crown
CDi2000
15
275122
Amplifier
Crown
CDi4000
Middle
Atlantic
Middle
Atlantic
Middle
Atlantic
NOTES
COLOR:BLACK
ERK4425
16
275122
Rack
17
275122
Drawerw/lock&foam
18
275122
RackPowerStrip
19
275122
AntennaCable(RG8)
WestPenn
25810
20
275122
SpeakerCable
WestPenn
25224B
21
275122
HearingAssistAntennaCable
WestPenn
25841
22
275122
MicrophoneCable
WestPenn
D25454
23
275122
SpeakerClusterandLRSpeakers
QSC
AP5152BK
COLOR:BLACK
24
275122
StageSpeakers
QSC
ADS52T
COLOR:BLACK
25
275122
SpeakerCeiling
QSC
ADC42T
COLOR:BLACK
26
275122
FrontFillSpeakers
QSC
I82H
COLOR:BLACK
27
275122
CobranetSwitch
Netgear
FS116E
28
275122
IntercomStation
ClearCom
PS702
29
275122
MixingConsoleCobranetCard
Yamaha
MY16CII
30
275122
Processor
BSS
BLU800
31
275122
DigitalBreakoutBoxProcessor
BSS
BLU32
32
275122
DigitalBreakoutBox
SKB
1SKBR4
33
275122
ShopDrawing
Zenith
27 51 22 - REVISED
UD4
PD915R
ITEM 1
CD-200I SPECIFICATIONS
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Plays audio CDs, MP3 CDs and WAV file CDs
Dock connector for Apple iPod charging and playback
iPod video playback from S-video or composite output
CD TEXT and ID3 tag support
Continue, Random and Program play modes
Repeat All and Repeat Single play modes
Index Search
Shock/skip prevention memory buffer
±12% pitch control (analog outputs only)
RCA unbalanced line outputs (CD and iPod)
Coaxial and Optical S/PDIF digital out (CD only)
1/4" stereo headphone output
2u rack mountable
Wireless 55-key remote control
19"W x 3.72" H x 11.73"D
9.3 lbs
ITEM 2
CD-RW900SL
Technical Documentation
PRODUCT OVERVIEW
One of the most popular CD recorders on
the market, the CD-RW900SL, features a
robust slot-loading transport, 24 bit A/D
& D/A converters, MP3 playback, key
control, sample rate conversion, and
selectable CD disc reading speed.
The CD-RW900SL provides dedicated analog front panel input control, rear panel unbalanced (RCA) I/O, and
S/DIFF digital I/O (optical and coaxial). Recently added features include Auto Cue and Auto Ready from the
menu, selectable I/R remote Enable/Disable, and MP3 Action Setting (prevents accidental termination of
continuous MP3 playback).
The features the user has come to expect from TASCAM are also included; Pitch Control on playback (0.1 to
1.0% in 0.1 steps), Auto or Manual track division, Sync Record Start, Power on Play, Elapsed, Remain, Total
and Total remain Time display, and CD-Text read and write.
Slot Loading Transport
Auto or Manual Track Division
24 bit A/D and D/A converters
All, single, or A-B repeat play
Sample Rate Conversion
Elapsed, remain, total, and total remain time
display
MP3 file Playback
Continuous, single, random, or program (up to 99
songs) play
MP3 Action setting
Key Control (change the key w/o changing the
speed)
Erase or Un-Finalize for CD-RW discs
Pitch Control
Selectable disc reading speed
Auto Cue from menu
Dedicated L/R input level control
Auto Ready from menu
Digital Attenuator
S/PDIF coaxial and optical digital I/O
CD-TEXT read and write
RCA Unbalanced analog I/O
PS/2 Keyboard input for CD-TEXT input and
remote control
+/_ 16% pitch control on playback
Power on Play
Sync Record Start
TASCAM 7733 Telegraph Road
Wireless (I/R) remote control unit (included)
Selectable Infra-red remote Enable/Disable
Montebello, CA 90640 (323) 726-0303 http://www.tascamcontractor.com
All features and specifications are subject to change without notice. Contact your local TASCAM representative for the latest information.
1
CD-RW900SL
PANELS
TASCAM 7733 Telegraph Road
Montebello, CA 90640 (323) 726-0303 http://www.tascamcontractor.com
All features and specifications are subject to change without notice. Contact your local TASCAM representative for the latest information.
2
CD-RW900SL
SPECIFICATIONS
Specifications
Recordable discs
CD-R, CD-R-DA, CD-RW, CD-RW-DA
Resolution
16 bit linear
Sampling frequency
44.1 kHz
Frequency converter input
32KHz to 48KHZ
Frequency response
20 Hz~20 KHz ±0.8 dB (playback) ±1.0 dB (recording)
S/N
95 dB (playback) 90 dB (recording)
Dynamic range
95 dB (playback) 90 dB (recording)
Distortion
0.006 % (playback) 0.008 % (recording)
Channel separation
90 dB (playback) 80 dB (recording)
Wow and flutter
< 0.001 % (Unmeasurable)
Analog inputs
Unbalanced RCA pin Level -10 dBV ±2 dB (Full Scale -16 dB)
Minimum input level -19 dBV (adjustable level at Full Scale -16
dB) Input impedance 22 KØ ±10% (unbalanced)
Analog outputs
Unbalanced RCA pin Level -10 dBV ±2 dB (Full Scale -16 dB)
Maximum output level +6 dBV ±2 dB Output impedance 600 Ø
±10% (unbalanced)
Phones
¼ “stereo phone jack”
20mW + 20mW (into 32 ohms)
Digital input
Coaxial RCA pin jack (IEC-60958 Consumer use) Optical
TOSLINK (IEC-60958 Consumer use)
Digital output
Coaxial RCA pin jack (IEC-60958 Consumer use) Optical
TOSLINK (IEC-60958 Consumer use)
Keyboard
Mini DIN 6 pin
Power
U.S.A./Canada 120 VAC, 60Hz
U.K./Europe 230 VAC, 50Hz
Australia 240 VAC, 50Hz
Power consumption
16 W (U.S.A./Canada)
18 W (U.K./Europe/Australia)
Dimensions
(d x w x h) 307.6 x 482.6 x 94
(mm) 12.1 x 19.0 x 3.7 (in)
Weight
4.5 kg (10 lb)
TASCAM 7733 Telegraph Road
Montebello, CA 90640 (323) 726-0303 http://www.tascamcontractor.com
All features and specifications are subject to change without notice. Contact your local TASCAM representative for the latest information.
3
CD-RW900SL
CHM99 | Navigation - EN | AKG
Page 1 of 1
ITEM 3
HEADPHONES
MICROPHONES
CHM99
WIRELESS
INTEGRATED SYSTEMS
Features
Specs
Downloads
PLUG 'N' PLAY INSTALLED MICROPHONES
GENERAL
POLAR PATTERNS
Audio Frequency bandwidth
18 mV/Pa
Equivalent Noise Level
21 dB-A
Signal to Noise
73 dB-A
Electrical Impedance
600 Ohms
Recommended Load Impedance
2000 Ohms
Polar Pattern
cardioid
POWERING INTERFACE Voltage
AUDIO OUTPUT
70 to 18000 Hz
Sensitivity
9 to 52 V
Current
3 mA
Type
Balanced XLR
Gender
Male
Contacts
3-pin
DESIGN
Finish
matte black or white
DIMENSIONS / WEIGHT
Net Weight
20 g
Height
55 mm
Diameter
13.5 - 13.5 mm
http://www.akg.com/CHM99-779.html?pid=985&techspecs
5/3/2013
Pro Co Sound | On Stage with the Best
Page 1 of 1
ITEM 4
Ameriquad Microphone Cable
xlrf/xlrm black/gold 24awg quad wire
Model
Description
AQ-3
MIC XF/XM 3FT LO-Z QUAD
AQ-5
MIC XF/XM 5FT LO-Z QUAD
AQ-10
MIC XF/XM 10FT LO-Z QUAD
AQ-15
MIC XF/XM 15FT LO-Z QUAD
AQ-20
MIC XF/XM 20FT LO-Z QUAD
AQ-25
MIC XF/XM 25FT LO-Z QUAD
AQ-30
MIC XF/XM 30FT LO-Z QUAD
AQ-50
MIC XF/XM 50FT LO-Z QUAD
AQ-100
MIC XF/XM 100FT LO-Z QUAD
Pro Co Ameriquad cables are the appropriate choice when you want studio reference sound quality or where high
RFI fields need to be dealt with.
The cable is a 24AWG quad cable with braided shield & custom double outer jacket with Kevlar core for added
strength and to prevent stretching. This is a studio reference cable with high quality, Black Amphenol XLR’s with gold
contacts on both ends. Ameriquad cables boast two tight-twist inner quad conductors for maximum conductivity, a
highly flexible cable construction, and terrific RFI rejection.
Pro Co Sound prides itself on the high integrity of its cables and warrants Ameriquad cables with an “any excuse,
even abuse” limited lifetime warranty against defects in workmanship and material.
http://www.procosound.com/products/catalog/show/14
12/16/2009
Internal: 44.1kHz, 48kHz
15Ω
PHONES OUT
8Ω Phones
40Ω Phones
600Ω Lines
430
480
25
XLR-3-31 type
with latch(Balanced)
Connector
Gain Switch*5
+24dB (default)
+18dB
-
Output Level
Nominal
Max. before clip
+4dBu (1.23 V)
+24dBu (12.3 V)
-2dBu (616mV)
+18dBu (6.16V)
75mW
150mW
65mW
150mW
Connector
Stereo Phone Jack (TRS) (Unbalanced) *2
XLR-3-32 type (Balanced) *1
Data Length
24bit
Format
IEC-60958 Consumer Use
220
25
Data Length
24bit
Format
IEC-60958
834
884
Level
0.5Vpp/75Ω
Level
0.5Vpp/75Ω
25
220
LS9-32
Connector
RCA Pin Jack
Connector
RCA Pin Jack
MY8-AE
8-Channel AES/EBU
format I/O
MY4-DA
4-Channel Analog
Output Card (20 bit)
8-Channel AES
3id-1995 format I/O
MY4-AD
4-Channel Analog
Input Card (24 bit)
8-Channel Analog
Input Card
MY8-AEB
MY8-AD96
8-Channel ADAT
format I/O
MY8-AT
8-Channel Analog
Output Card
MY8-DA96
16-Channel
AES/EBU format I/O
16-Channel ADAT
format I/O
8-Channel Analog
Input/Output Card
MY16-AE
MY16-AT
MY8-ADDA96
16-Channel Audio
CobraNet format I/O
and Control I/O
MY16-CII
This document is printed on
chlorine-free (ECF) paper with soy ink.
For details please contact:
Standard Series
96 kHz Series
16 I/O Series
LPA522
8-Channel TDIF
format I/O
MY8-TD
8-Channel AES/EBU
format I/O
MY8-AE96
16-Channel TDIF
format I/O
MY16-TD
Printed in Japan
8-Channel Analog
Input Card (24 bit)
MY8-AD24
(with sample rate converter)
8-Channel AES/EBU
format I/O
MY8-AE96S
LS9-32 has 2 Mini-YGDAI card slots, the LS9-16 has one. Each slot offers up to 16 I/O channels, with Mini-YGDAI cards available for digital I/O on ADAT, TASCAM or
AES/EBU formats, or for extra analog I/O capability.
Yamaha Mini-YGDAI cards
25
COAXIAL
Terminal
2TR OUT DIGITAL
LS9-16
COAXIAL
Terminal
2TR IN DIGITAL
unit : mm
Sensitivity *1
-82dBu (61.6μV)
-10dBu (245mV)
-20°C to +60°C
Storage Temperature Range
Input Level
Nominal
Max. before clip
-62dBu (0.616mV) -42dBu (6.16mV)
+10dBu (2.45V)
+30dBu (24.5V)
+10°C to +35°C
LS9-16: 95 W, 110–240 V, 50/60 Hz
LS9-32: 170 W, 110–240 V, 50/60 Hz
LS9-16: 12kg
LS9-32: 19.4kg
*1. XLR-3-32 type connectors are balanced.( 1=GND, 2=HOT, 3=COLD ) *2. PHONES stereo phone jack is unbalanced.( Tip=LEFT, Ring=RIGHT, Sleeve=GND ) *3. In these specifications, 0dBu = 0.775 Vrms. *4. All output DA converters are 24bit, 128times oversampling.
*5. There are switches inside the body to preset the maximum output level.
75Ω
Digital Output
Characteristics
Dimensions
3kΩ
Actual Source For Use With
Impedance
Nominal
OMNI OUT 1-8 <LS9-16>
OMNI OUT 1-16 <LS9-32>
Output Terminals
Digital Input
Characteristics
Analog Output
Characteristics
INPUT 1-16 <LS9-16>
INPUT 1-32 <LS9-32>
LS9-32: 884 x 220 x 500
LS9-16: 480 x 220 x 500
Temperature Range Operation free-air
Power Requirements
Net Weight
Dimensions (W x H x D mm)
*1. Sensitivity is the lowest level that will produce an output of +4dBu(1.23V) or the nominal output level when the unit is set to maximum gain. (all faders and level controls are maximum position.) *2. In these specifications, 0dBu = 0.775 Vrms. *3. All input AD converters are 24bit
linear, 128times oversampling. *4. +48V DC ( phantom power ) is supplied to INPUT XLR type connectors via each individual software controlled switch.
GAIN
-62dB
+10dB
Input Terminals
500
Analog Input
Characteristics
48V
Phantom Power
For Use With
Nominal
50-600Ω Mics &
600Ω Lines
320 x 240 dots Graphic Color LCD
Actual Load
Impedance
100mm motorized x33 <LS9-32> , x17 <LS9-16>
LCD Display
External: 39.69 - 50.88kHz
Fader
Sampling Frequency
General Specifications
LS9 Specifications
500
ITEM 5
PRELIMINARY
2
discerning professionals choose Yamaha Digital Mixing Consoles for critical live sound applications around the globe.
And then there’s the sound. From the acclaimed PM1D digital live sound console right down the line, superlative sound is another reason
up to another 16 or 32 channels of audio inputs from digital sources and/or analog sources with no compromises on features or quality.
mixers. Both LS9-16 and LS9-32 can grow with your needs too; they have a second layer of channel processing power that lets you control
that with a 32 channel analog console and the racks of outboard gear that would be required to equal the functionality of these digital
remarkably compact and lightweight – even the LS9-32 can be tucked under an arm and moved around quite comfortably. Just try doing
capabilities in their class, with an interface that makes operation easy even for the inveterate analog user. They do it in consoles that are
digital. The Yamaha LS9-16 and LS9-32 are two very good reasons indeed. They offer the most up-to-date and mature digital mixing
commercial advantage. If you’re planning to upgrade a small or medium-scale analog system, there are plenty of great reasons to go
demanding sound engineers and audio company professionals are turning to digital mixing as a way of enhancing quality, efficiency and
Digital mixing and processing for live sound has come of age, and there’s no turning back. Throughout the audio industry the most
Good Reasons to Go Digital
• 16 or 32 top-performance recallable head amplifiers deliver microphone
and line sources with extraordinary presence and realism.
• An additional 16 or 32 channels of processing power ready to receive
audio via the Mini-YGDAI expansion slots, providing a total of 32 or 64
channels!
• 4 stereo input channels.
• An extensive range of channel functions accessible via Yamaha’s
acclaimed Selected Channel interface.
• Versatile bus architecture with comprehensive digital patching capability:
16 mix buses, 8 matrix buses, and a stereo and mono bus that can be
used in LCR mode.
• Virtual GEQ and effect rack offers easy access to built-in graphic
equalization and effects that would fill a full-size rack or two if similar
analog gear were used.
• Built-in USB Memory Recorder/Player eliminates the need for an external
device for simple off-board recording, and can supply background music
and sound effects as required.
• Full-console scene Store and Recall.
• Ready to use out of the box with pre-patched effects and pre-fader aux
mixes for monitor sends.
• One or two Mini-YGDAI slots for easy system expansion.
• Compact size 480 x 220 x 500 and 884 x 220 x 500 weigh only 12 and
19.4 kg, respectively.
Main Features
3
4
The LS9-16 can be rack-mounted using an
optional rack-mounting kit for optimum
integration with any system.
Additionally the same kit can be used as
fixing tool for the LS9-32.
The surprisingly small size and lightweight of the LS9-16 make it a perfect choice for
applications that require maximum portability and handling ease. Use it for events or
temporary live sound setups, and benefit from the power and performance of much larger
and more complex systems in an eminently portable package that can be set up and
operated anywhere with ease.
The
:
Anywhere You Need Advanced Live Sound Support
Suppose you need a compact console, but also graphic
equalizers for front-of-house and monitors, a couple of
effect processors for reverb and delay, compressors and
gates, a 2-track player/recorder for BGM and reference
recording … that’s already a fairly large rack full of gear,
but it’s still a bare minimum for most serious sound
applications. Think about transporting and setting up all
that gear (don’t forget all the cables you’ll need), and
add up the cost in terms of the equipment itself as well
as transportation, staff, storage, and maintenance.
Now imagine all of that and much more in a single
rackmount console that weighs only 12 kg, and you have
the LS9-16. It’s all pre-patched and tested in the factory
Compare the Cost and Complexity
so you just need to connect microphones to the inputs
and speakers to the outputs and you are ready for
soundcheck. If you need more capacity you can use the
Mini-YGDAI expansion port system to connect a couple
of rackmount head amplifier and have up to 32 channels
without taking up much more space. The advantages are
obvious for touring and temporary systems, but installations will also benefit from the significant space savings
and reduced cabling requirements. And of course
everybody – audience included – benefits from the
outstanding versatility and sound these extraordinary
digital consoles deliver.
line-ups. Whether used in an installation or on the road, the LS9-32 will deliver the performance and versatility
of large-scale systems in dramatically less space, with less hassle, and significantly lower overall cost.
With 32 input head amps the LS9-32 can comfortably handle the complex and varied source requirements
presented by a wide range of live sound applications, but it’s always reassuring to know that you can expand it
up to 64 channels by just adding external preamps and Mini-YGDAI interface cards for those extra demanding
The
:
High Input Capacity and a Generous Bus Structure
for Serious Live Sound
Console lamp accepts the
Yamaha option gooseneck lamp
LA5000 (sold separately).
5
6
A headphone jack and
level control are
conveniently located on
the console’s front panel.
REAR PANEL
REAR PANEL
One of the reasons the LS9 consoles are so
compact – and another reason you’ll want to go
digital – is that a total of 17 physical faders on
the LS9-16, or a total of 33 on the LS9-32, give
you fast, easy access to all input channel, mix
bus, matrix, and master levels. On both consoles
the input channels are available in two fully
patchable layers: 1~16 and 17~32 on the LS9-16,
or 1~32 and 33~64 on the LS9-32. And you can
switch between layers instantly by tapping a
single dedicated button. You can organize your
inputs so that channels you’ll want to operate
most of the time are in the “top” layer, or you
can “vertically” link input channels across the
two layers for stereo operation. Of course you
can link channels “horizontally” in the same
layer if you like, but pairing vertically keeps
controls you don’t need to operate out of the
16 or 32 Mono Input Channels Plus 4
Stereo Input Channels Expandable Up to
32 or 64 Channels in Two Layers
The LS9-16 and LS9-32 make immense digital
processing power and control flexibility
available via an interface that will quickly
become comfortable and convenient for the
first-time user. Anyone who has ever used a
Yamaha digital console before will feel right at
home. Fader levels are directly controlled via
precision 100-millimeter motor faders for instant
hands-on access. Corresponding illuminated
switches are provided for channel on/off
switching and cueing, and independent LED
level meters let you keep an eye on channel
signal levels. Yamaha’s acclaimed Selected
Channel interface provides efficient access to
other channel functions via an ingenious
integration of physical controllers and a large
color LCD panel. Deeper functions and system
settings can be efficiently accessed via the
console’s “Display Access” keys and programmed
via the LCD display and data entry controls. A
“Home” key brings you right back to the main
operating mode no matter where you are, so
you need never be lost in menus.
Intuitive Interface for Easy Access and
Control
way. You can even
“Y-split” channels to
appear in both layers and
have a monitor and a FOH
layer. There’s also a
“Master” layer button that
brings all 16 mix bus levels
to the console’s faders on
the LS9-16, and additionally the matrix levels and
mono bus level on the 33-fader LS9-32. In
addition to the two input channel layers and
master layer, the LS9 consoles feature a “Custom
Fader” layer to which you can assign any
combination of input and output channel faders
your application requires.
Stereo inputs are handled in a similar way on
the LS9-16, with two stereo inputs on each of
the input layers. The LS9-32 provides panel
controls for all four stereo inputs.
The LS9-16 provides 16 analog inputs built-in,
while the LS9-32 has 32 internal analog inputs.
Additional inputs can be provided via the
LS-9-16’s single rear-panel Mini-YGDAI expansion slot, or the dual expansion slots provided on
the LS9-32.
LS9 General Function
The 16 mix buses can
function as any
combination of 16
auxiliary sends or
sub-groups. That’s a lot
of AUX knobs and/or
faders. However on the
LS9 consoles the mix bus levels are controlled via
the “1-16, 17-32 or 1-32, 33-64” fader layer with
the simple Sends on Fader function. Just touch
the “Master” button and faders 1 through 16
directly control the mix bus levels. Each of the
mix buses can be easily assigned for mono or
stereo operation. You can also choose the send
point to be pre or post fader, and when it’s
pre-fader you can even select the send point to
be pre or post EQ and dynamics. But don’t worry
about the choices because Yamaha provides an
easily recalled default setup scene that lets you
get mixing straight out of the box.
The LS9 also features an 8-bus matrix that can be
used to provide additional outputs whenever
they are needed. The matrix can receive signals
from output groups so it can be used to create
extra monitor mixes or used for different level
and EQ setting in a distributed PA system. And
for main output both models have a stereo bus
and a mono bus that can either be used
independently or in LCR mode with proper LCR
pan control.
Outputs can be patched to any of eight analog
“Omni” outputs on the LS9-16, or 16 omni
outputs on the LS9-32. Additional outputs can
be provided via the rear-panel Mini-YGDAI
expansion slots – one slot on the LS9-16, and
two slots on the LS9-32.
16 Mix Buses, 8 Matrix Buses, Plus
Stereo and Mono Buses with LCR Mode
7
8
With the default setup
DYNAMICS 1 adjusts
gate threshold level for
input channels or
compressor threshold
level for mix, matrix, or stereo/mono channels,
and DYNAMICS 2 adjusts compressor threshold
level for input channels. The actual parameter
controlled depends on the dynamics processor
selected from the console’s comprehensive
dynamics library – including a de-esser for
advanced vocal processing. Although initially set
up for gating and compression, as described
above, you can also use both processors for
DYNAMICS 1
and DYNAMICS 2
Pan control for mono channels, and balance
control for stereo channels. The PAN control can
be assigned to either standard stereo LR or LCR
operation. In the LCR mode a CSR (Center-Side
Ratio) control becomes available that can be
used to adjust the proportion between center
and LR non-center signal.
PAN
Adjusts input-channel
head amplifier (pre
amplifier) gain to
match the channel’s
input sensitivity to the
source microphone or
line input. HA gain is recallable, as are the +48V
phantom power and phase settings.
HA GAIN
The LS9 consoles have a powerful range of
channel functions that can be accessed and used
as easily as those on any analog console – the
only difference being that if all of these
functions were provided on an analog console
the modules would be impractically long! Simply
press the [SEL] key of the channel you want to
control and use the appropriate Selected
Channel encoder to adjust as required:
Comprehensive Channel Functions with
Intuitive Selected Channel Control
Head amplifier are the analog
circuits that are critical to
determining the console’s final
sound and raising the signal
level prior to digital conversion.
The LS9 head amps are the
finest quality you’ll find in any
console in this class and are capable of accepting
mic and line level inputs without a switch.
In addition to exceptionally low noise and
distortion (minimum requirements for any serious
head amp), these superb amplifiers deliver
exceptional accuracy and presence that
contributes to maximum live-sound intelligibility
and impact. But there’s more. Although the LS9
head amplifier are analog for quality and “feel”
they are still digitally “recallable”, meaning that
their gain, phase, and phantom power settings
are stored and recalled with the console’s scenes.
High-performance Recallable Head Amps
LS9 General Function
Most live sound applications will require graphic
equalization for room EQ and effects like reverb
or delay for creative sound engineering. The LS9
offers effects from Yamaha’s world leading,
industry standard SPX range, and full 31 band
Virtual Rack with Extensive Effects and EQ
When it comes to
marking up the console
there’s nothing quite
like your familiar hand
writing on tape for
labeling inputs , but
the LS9 also offers
some inbuilt channel identification capabilities
that you’ll appreciate. The number, name, and
icon of each channel appears in the upper left
corner of the display, and you can enter names
of up to 8 characters and select icons from the
impressive selection provided for easy channel
identification. Electronic names are essential for
working with the remote editor in Yamaha
Studio Manager too.
Channel Names & Icons
This encoder adjusts
the send level to the
mix or matrix bus
currently selected via
the MIX/MATRIX keys
to the left of the
display. Depending on your application you can
think of it as an auxiliary, monitor, effect, or
group send control. “VARI” pre-EQ and
pre-fader modes are provided for auxiliary send
applications and a “FIXED” mode is provided for
convenient group send operation.
SELECTED SEND
This versatile 4-band
fully parametric EQ
section affords
extraordinary control
and quality for all
inputs and buses, and
includes a variable HPF filter. You can directly
control the Q, frequency, and gain of each band
from the encoders, or move the cursor to an EQ
parameter and hit the [ENTER] key to access the
wide-range attenuator, and see a larger graphic
representation of the EQ curve.
EQ
compression if required. Move the cursor to a
dynamics parameter and hit the [ENTER] key to
access the remaining comp and gate parameters
as well as the DYNAMICS preset library.
Mute grouping is another feature that can be
great advantage in live sound applications. Any
number of channels can be muted or unmuted
either via mute master controls in the display, or
Mute Groups
For direct hands-on control you can adjust
individual bands from the console’s faders in
much the same way as you’d adjust the EQ
bands on an external GEQ unit. With the LS9 -16
you need to select the group of faders to adjust,
but on LS9- 32 you can see the full 31band curve.
Another convenient-control feature is the ability
to instantly reset any band to nominal simply by
pressing the corresponding fader’s [ON] key.
Direct EQ Control
The standard LS9 graphic EQ modules are
31-band types for precise response shaping and
pinpoint feedback control. But when you need
even more graphic EQ capacity and flexibility
you can call up the innovative Flex15GEQ
modules. Each Flex15GEQ module functions as
two 31-band units with 15-bands available at a
time. So if you choose to load all of your rack
spaces with Flex15GEQ, you have an
extraordinarily versatile16 channels of GEQ!
Standard 31-band or Flex15GEQ
There’s a very good reason that Yamaha digital
effects are highly regarded in the professional
sound field: they are simply the best there is. In
both the LS9-16 and LS9-32 you have an
extensive range of top-quality effects – from
ambience and echo to modulation and
distortion – that you can access and add to the
mix when and wherever needed.
High-resolution Effects
graphic EQ as well as the innovative “Flex
15GEQ”. Normally you’d need a rack full of
external signal processing gear to support even
relatively simple live sound requirements, but
not with an LS9 console. Just touch one of the
RACK buttons and the virtual effect and EQ rack
appears on the display for instant, easy access.
Effects and graphic EQ can easily be patched
into any channel and output, and of course you
can edit the effects in detail to create precisely
the sound you need. You can use up to 8 signal
processors simultaneously: normally up to 4
effects and 4 graphic EQ units. But since the
effect units can also function as graphic EQs, you
can use more EQ units if you don’t need all 4
effects … up to a total of 8 graphic EQs if you
don’t need any other effects.
Virtual Rack
Scene recall is an
invaluable feature on
its own, but with Recall
Focus and Recall Safe
functions it becomes a
tool you won’t want to
be without. Recall Focus
lets you specify the parameters to be recalled with
a particular scene, while Recall Safe works
globally to all scenes, allowing you to specify
parameters that are not to be altered by any
scene recall. For example you could use Recall Safe
on input EQs so that any EQ changes you make in
the first scene of a play don’t get undone when
you recall scene two. The combination of both
Recall Safe and Focus lets you easily switch
between the live mics on stage and a multirack
recorder input and then listen to the playback
using the stored scenes used to make the
recording.
Recall Focus and Recall Safe Functions
How long does it take
you to zero the settings
on an analog console,
or reproduce the
desired settings for a
particular
performance? The
answer depends on the console and application,
but it does take operator time and it’s hard to be
accurate and reliable for what can easily be
several thousand positions. Scene memory is the
digital solution, and if you’ve never used a
digital console before you’ll really appreciate the
time and effort saved by this feature. A “scene”
is a complete snapshot of all the console’s
settings. The LS9 consoles lets you store up to
300 complete scenes for instant recall whenever
they’re needed. You can, for example, reset the
entire console for band changes or different
scenes in a theatrical performance in an instant.
You can also store basic setups for a number of
different types of shows your system may be
required to handle, then recall and tweak the
settings as required.
Full-console Scene Storage and Recall
When working on a monitor mix try using Sends
on Fader mode. Touch the currently active
MIX/MATRIX button (or press an inactive
MIX/MATRIX button twice) to instantly assign
the corresponding mix bus sends to the faders so
you can visually confirm send levels and adjust
them using the high quality 100mm full-length
linear faders. Touch the same MIX/MATRIX
button again to return to the normal mix mode.
Sends on Faders
via User Defined Keys
(see below) for direct
access. Up to 8 mute
groups can be
specified.
The LS9 data “libraries” provide extensive
resources to draw on when setting up effects,
parametric EQ, graphic EQ, or dynamics
processing. You can recall an appropriate preset
Data Libraries
Most live-sound systems include a CD player
and/or recorder of some sort to provide
background music and allow recording of the
program for reference purposes. That’s one or
two more pieces of external equipment that
won’t be required with an LS9 console. The
LS9-16 and LS9-32 feature a built-in USB Memory
Recorder/Player that works with USB memory
sticks plugged into the console’s USB port. You
can record MP3files and play back MP3, AAC,
and WMA files at 96, 128, or 192 kbps. You can
even cue playback of specific files from the
console’s User Defined Keys!
Built-in USB Memory Recorder/Player
Since we don’t know exactly
what functions you’ll need to
access for your particular
application, we’ve provided a
group of 12 User Defined Keys
that can be assigned a wide
range of functions. You use
them to jump to specific display
screens, assign them to function as mute masters
for specified mute groups, or assign one for
tap-tempo input of delay times. There’s also an
innovative “Set by SEL” function with which the
channel [SEL] keys perform a range of alternate
functions if pressed while the assigned User
Defined Key is held: reset the defaults for that
channel, turn phantom power on or off, set the
channel fader to nominal … and more.
User Defined Keys
Here are a few more features that add
significantly to the attraction of digital
technology for live sound. Channel Copy lets you
copy the parameters from any one channel to
any number of other channels, Channel Move
swaps the parameters and the patching between
two specified channels, and Channel Clear clears
all parameters of the specified channels. All of
these capabilities can dramatically streamline the
process of setting up the console or modifying
the console settings.
Channel Copy, Move and Clear
In addition to the large stereo level meter,
accurate fast-response metering for all channels
and buses is easily accessible via the LS9 display.
A variety of metering points can also be selected
so you have comprehensive visual monitoring of
signal levels throughout the entire console.
Flexible Multi-point Metering
Touch the “Monitor” display access button for
full access to the console’s extensive range of
monitor functions: from monitor source
selection through talkback and oscillator
controls. A headphone jack and level control are
conveniently located on the front panel or
monitor signals can be routed to one of the
Omni output XLRs and slots. Any of the input
channels can be assigned to talkback operation
for convenient system testing. And of course
independent physical [CUE] buttons are
provided with each fader for instant, error-free
cue monitoring.
Versatile Monitoring Capability
and use it the way it is,
or tweak it to suit
specific needs. As an
example, you might
recall a vocal
compressor preset from
the dynamics library
and then adjust the threshold to suit the source,
or recall a kick-drum EQ preset and adjust the
center frequency to match the drum actually
being used. You can also save your edited versions
of the presets for easy recall whenever they’re
needed again.
9
10
The LS9-16 has one expansion slot on the rear
panel, and the LS9-32 has two. The expansion
slots accept a wide range of optional Yamaha
and third party Mini-YGDAI I/O cards that can be
used to add analog or digital input and output
capability in a range of formats. You can even
Mini-YGDAI Expansion Cards
a flexible means of preventing unauthorized
access to the console, or restricting access to a
limited set of functions. User access can be
controlled either via passwords or USB memory
keys. The administrator can assign specific
functions to each unique password or key, so the
user only has to log onto the console with the
assigned password or insert the USB key to
begin operation at the assigned level. USB
memory keys can be easily created either directly
via the console or a computer running the LS9
Editor applications software. As an added bonus
the same USB memory key used for access can
also be used to store the user’s scenes and other
preferences.
The LS9 Editor application for Yamaha’s Studio
manager host program running in MS Windows
operating systems gives you off-line
programming access to most console
parameters. You can set up and edit console
parameters anywhere you can use your personal
computer – in the office, on the road, in your
hotel. A comprehensive graphical interface
makes locating and editing parameters easy, and
you can download setups from the computer to
the console either by directly connecting the
computer to the console via an Ethernet cable,
or by saving the data to a USB memory stick that
can then be plugged into the console’s USB port.
You can even remotely control the console from
the computer in real time while connected via
Ethernet.
LS9 Editor for Online Control or Offline
Editing
In addition to the analog inputs and outputs
and expansion slots, the LS9-16 and LS9-32
rear-panels feature MIDI terminals, word clock
input and output connectors that allow full
word sync with other digital audio gear, S/PDIF
format digital 2-track inputs and outputs, and
an Ethernet network connector.
Other Rear-panel Features
use Mini- YGDAI cards to bus-cascade with other
consoles for significantly expanded input
capacity.
The amount of signal processing power packed
into the LS9 consoles is really quite impressive
when looked at from the perspective of a
comparable analog system. Here’s an example:
if you wanted to replace a fully loaded LS9-32
with analog gear you’d need a large
32-channel console plus some racks loaded
with 32 gates each, some racks loaded with 32
compressors each, another rack containing
Comp
four GEQ units and four signal processors for
effects, and perhaps yet another rack
containing your CD player and recording gear.
And what a wiring and patching nightmare!
When you consider that you get all of this and
more in a compact console that a single person
can pick up and move around without
breaking into a sweat, the choice is obvious.
32 Inputs Large Analog SR Console + Outboard Racks
Gate
CD Player
MD Recorder
Delay 2
4
3
2
1
Delay 1
Reverb 2
Reverb 1
31 band GEQ
(Stereo)
31 band GEQ
(Stereo)
31 band GEQ
(Stereo)
31 band GEQ
(Stereo)
LS9 Digital vs. Conventional Analog Systems
You might simply
want to prevent
“accidents”
during critical live
performances, or
limit access to
specific functions
in order to
minimize the need
for direct supervision of inexperienced
operators. You may have spent hours with an
analyzer setting up the EQ to precisely tune the
system for a room, for example, in which case
you won’t want those settings changed under
any circumstances. Access management provides
Advanced Access Management
Standard USB memory sticks can be plugged into
the LS9 USB port for convenient storage and
recall of scenes, patches, user libraries, channel
names, preferences … essentially all system data.
In addition to providing a secure backup, this
makes it easy to transfer data between the
console and the LS9 Editor application running
on your personal computer, or directly between
LS9 consoles. You can program the console’s
settings using the LS9 Editor on a computer in
your hotel room or on the tour bus – wherever
you don’t have access to the console itself – and
simply transfer those settings from your USB
memory to the console at the venue.
USB Memory for Convenient Data
Management and Portability
LS9 General Function
Block Diagram
DIGITAL MIXING CONSOLE
LS9
11
ITEM 6
Wireless Microphones
ULX WIRELESS MICROPHONE SYSTEMS
SPECIFICATION SHEET
6-945"/%"3%
6-91%*7&34*5:3&$&*7&3
6-9 4UBOEBSE 6)' TZTUFNT SFQSFTFOU B CSFBLUISPVHI
JO QFSGPSNBODF BOE QSJDF GPS CPUI XPSLJOH NVTJDJBOT
BOE QSPGFTTJPOBM TPVOE JOTUBMMFST .VMUJQMF TZTUFN
DPOGJHVSBUJPOTQSPWJEFMJNJUMFTTPQUJPOTFBDIXJUIBDIPJDF
PG MFHFOEBSZ 4IVSF NJDSPQIPOF USBOTNJUUFST 0WFS TFMFDUBCMF QSFࣇQSPHSBNNFE GSFRVFODJFT BSF BWBJMBCMF
BOE "VUPNBUJD 'SFRVFODZ 4FMFDUJPO QSPWJEFT B TUSBJHIU
TIPUUPBDMFBSDIBOOFM
ࣖ "VUPNBUJD'SFRVFODZ4FMFDUJPOXJUIHSPVQTDBOGVOD
UJPO
ࣖ 0WFSTFMFDUBCMFGSFRVFODJFT
ࣖ 1SFEJDUJWF%JWFSTJUZ
ࣖ ࣇTFHNFOUBVEJPNFUFS
ࣖ ࣇTFHNFOU3'NFUFS
ࣖ "EWBODFENVMUJࣇGVODUJPO-$%
ࣖ 4RVFMDIBEKVTUNFOU
ࣖ SBDLEFTJHO
ࣖ *OࣇMJOF%$QPXFSPOBOUFOOBDPOOFDUJPOT
ࣖ 3FNPUBCMFXBWFBOUFOOB
ࣖ 'SFRVFODZBOEWPMVNFMPDLPVU
ࣖ 3VHHFENFUBMDIBTTJT
ࣖ 'VSOJTIFESBDLIBSEXBSF
ࣖ -PDLJOH%$DPOOFDUPSPOUIFQPXFSTVQQMZ
ࣖ 9-3BOE࣑PVUQVUT
6-9"/%6-953"/4.*55&34
ࣖ ࣇTFHNFOUCBUUFSZGVFMHBVHF
ࣖ #BDLMJU-$%TIPXTHSPVQBOEDIBOOFM
ࣖ "EKVTUBCMF'SFRVFODZTFUUJOHT
ࣖ 6QUPTFMFDUBCMFGSFRVFODJFT
ࣖ 'SFRVFODZBOEQPXFSMPDLPVU
ࣖ IPVSCBUUFSZMJGF
ࣖ GUN
PQFSBUJOHSBOHF-JOFPGTJHIU
ࣖ ࣇE#QBETXJUDIPO6-9
/05&"WBJMBCMFGSFRVFODJFTEFQFOEPOUIFBQQMJDBCMF
SFHVMBUJPOTJOUIFDPVOUSZXIFSFUIFTZTUFNJT
VTFE
6-9130'&44*0/"-
4UFQ VQ UP 6-9 1SPGFTTJPOBM XJSFMFTT 6)' TZTUFNT GPS
XPSLJOH NVTJDJBOT BOE QSPGFTTJPOBM TPVOE JOTUBMMFST
.VMUJQMF TZTUFN DPOGJHVSBUJPOT QSPWJEF MJNJUMFTT PQUJPOT
FBDIXJUIBDIPJDFPGMFHFOEBSZ4IVSFNJDSPQIPOFT6Q
UP TFMFDUBCMF QSFࣇQSPHSBNNFE GSFRVFODJFT BSF
BWBJMBCMFBOE"VUPNBUJD'SFRVFODZ4FMFDUJPOQSPWJEFTB
TUSBJHIUTIPUUPBDMFBSDIBOOFM6-91SPGFTTJPOBMTZTUFNT
PGGFS NPSF BEWBODFE GFBUVSFT BOE DPOUSPMT JODMVEJOH
MPDLBCMFTFUUJOHTBOEHSPVQTDBOGVODUJPO
6-94%*7&34*5:3&$&*7&3
ࣖ "VUPNBUJD'SFRVFODZ4FMFDUJPO
ࣖ 0WFSTFMFDUBCMFGSFRVFODJFT
ࣖ 1SFEJDUJWF%JWFSTJUZ
ࣖ 3'QSFTFODF-&%
ࣖ ࣇTFHNFOUBVEJPNFUFS
ࣖ ࣇTFHNFOUUSBOTNJUUFSCBUUFSZGVFMHBVHF
ࣖ .VMUJࣇGVODUJPO-$%
ࣖ SBDLEFTJHO
ࣖ %FUBDIBCMFXBWFBOUFOOBT
ࣖ %VSBCMFQMBTUJDDIBTTJT
ࣖ -PDLJOH%$DPOOFDUPSPOUIF1PXFS4VQQMZ
ࣖ 9-3BOE࣑PVUQVUT
ࣖ .JDMJOFTXJUDIBCMF9-30VUQVU
ࣖ *OMJOF%$1PXFSPO"OUFOOB$POOFDUJPOT
ULXS4
ULXP4
ULX1
i4IVSF*ODPSQPSBUFE
5-3FW
ULX2
1SJOUFEJO64"
41&$*'*$"5*0/4
*NBHF3FKFDUJPO
E#UZQJDBM
3'$BSSJFS'SFRVFODZ3BOHF
4QVSJPVT3FKFDUJPO
UP.)["WBJMBCMFGSFRVFODJFT
EFQFOEPOUIFBQQMJDBCMFSFHVMBUJPOTJOUIFDPVOUSZ
XIFSFUIFTZTUFNJTVTFE
3FGFSUPUIFGSFRVFODZ
TVQQMFNFOUTVQQMJFEXJUIUIFTZTUFN
E#UZQJDBM
6MUJNBUF2VJFUJOHSFGFSFODFqL)[EFWJBUJPO
E#"XFJHIUFE
4ZTUFN%JTUPSUJPOSFGFSFODFqL)[EFWJBUJPO
L)[NPEVMBUJPO
&GGFDUJWF3BOHF
NGU
VOEFSPQUJNBMDPOEJUJPOT
UPUBMIBSNPOJDEJTUPSUJPOUZQJDBM
/05&"DUVBMXPSLJOHSBOHFEFQFOETPO3'TJHOBM
BCTPSQUJPOSFGMFDUJPOBOEJOUFSGFSFODF
1PXFS3FRVJSFNFOUT
6-96-97BMLBMJOFCBUUFSZ7/J.)N"
PQUJPOBM
6-946-917EDOFHBUJWFHSPVOE
N"
"VEJP'SFRVFODZ3FTQPOTF
UP)[qE#
/05& 0WFSBMMTZTUFNGSFRVFODZSFTQPOTFEF
QFOETPOUIFNJDSPQIPOFFMFNFOU
#BUUFSZ-JGF
UPIPVSTXJUI7BMLBMJOFCBUUFSZ
5SBOTNJUUFS"VEJP1PMBSJUZ
0QFSBUJOH5FNQFSBUVSF3BOHF
1PTJUJWFQSFTTVSFPONJDSPQIPOFEJBQISBHNPS
QPTJUJWFWPMUBHFBQQMJFEUPUJQPG8"QIPOFQMVH
QSPEVDFTQPTJUJWFWPMUBHFPOQJOXJUISFTQFDUUP
QJOPGMPXJNQFEBODFPVUQVU
BOEUIFUJQPGUIFIJHI
JNQFEBODFJODIPVUQVU
pUPp$pUPp'
/05&#BUUFSZDIBSBDUFSJTUJDTNBZMJNJUUIJTSBOHF
0WFSBMM%JNFOTJPOT
6-9NN)YNN8YNN%Y
YJO
6-94.-YNN%JBYJO
6-9#&5"NN-YNN%JBYJO
6-94.NN-YNN%JBJOYJO
6-96-9#&5"NN-YNN%JB
YJO
6-94NN)YNN8YNN%JO
YJOYJO
6-91NN)YNN8YNN%JO
YJOYJO
5SBOTNJUUFS(BJO"EKVTUNFOU3BOHF
6-9E#
6-9E#
3FDFJWFS"VEJP0VUQVU-FWFMqL)[EFWJBUJPOL)[UPOF
9-3DPOOFDUPSJOUPPINMPBE
E#7MJOF
ࣇE#7NJD
JODIDPOOFDUPSJOUPPINMPBE
ࣇE#7
*NQFEBODF
6-9JOQVU
.FHPIN6-946-91PVUQVU
PINTBUMJOFMFWFMPINTBUNJDMFWFM
/FU8FJHIU
6-9HP[
XJUIPVUCBUUFSZ
6-96-9#&5"HP[
XJUIPVU
CBUUFSZ
6-94.HP[
XJUIPVUCBUUFSZ
6-96-9#&5"HP[
XJUIPVU
CBUUFSZ
6-94HMCTP[
6-91HMCTP[
.PEVMBUJPO
qL)[EFWJBUJPODPNQSFTTPSFYQBOEFSTZTUFNXJUI
QSFBOEEFFNQIBTJT
3'1PXFS0VUQVU
6-96-9N8NBYJNVN
%ZOBNJD3BOHF
E#"XFJHIUFE
3'4FOTJUJWJUZ
˨7GPSE#4*/"%UZQJDBM
ULX1 Bodypack Transmitter
4-PIN MINI CONNECTOR
CONDENSER MICROPHONE
BODYPACK TRANSMITTER
TA4F
TA4M
+5V
AUDIO
4.7 μf
27 pf
27 pf
GROUND
TA4F
INSTRUMENT CABLE
AUDIO
TIP
SLEEVE
SHIELD
6-95SBOTNJUUFS*OQVU
$POOFDUPS
$POGJHVSBUJPO
.JDSPQIPOFQJOT
BOEUJFEUPHFUIFS
(VJUBSXJUI8"
5".
5".
6OCBMBODFEBDUJWF
6-95SBOTNJUUFS*OQVU
$POGJHVSBUJPO
6OCBMBODFEBDUJWF
"DUVBM*NQFEBODF
L˕
.˕
.BYJNVN*OQVU
-FWFM
E#77QQ
(BJO4XJUDIE#E#7
7QQ
6OCBMBODFEBDUJWF
"DUVBM*NQFEBODF
L˕
.BYJNVN*OQVU-FWFML)[5)%
E#77QQ
(BJO4XJUDIE#
E#77QQ
1JO"TTJHONFOUT
(SPVOE
7UISPVHI
L˕
.JDSPQIPOF#JBT
"VEJP
'&5BDUJWFMPBE
(SPVOE
/P$POOFDUJPO
"VEJP
/P$POOFDUJPO
6-916-943FDFJWFS"VEJP0VUQVU
6-916-943FDFJWFS"OUFOOB*OQVU
$POOFDUPS
6OCBMBODFEJO
#BMBODFE9-3
"DUVBM*NQFEBODF
L˕
.JD-FWFM˕
-JOF-FWFM˕
1JO"TTJHONFOUT
5JQ)PU
3JOH4MFFWF(SPVOE
(SPVOE
)PU
$PME
1IBOUPN1PXFS1SPUFD
UJPO :FT
:FT
'VSOJTIFE"DDFTTPSJFT
$POOFDUPS5ZQF
#/$
"DUVBM*NQFEBODF
˕
/PNJOBM*OQVU-FWFM
ࣇUPࣇE#N
.BYJNVN*OQVU-FWFM
E#NࣇE#NSFDPNNFOEFE
1JO"TTJHONFOUT
4IFMM(SPVOE$FOUFS4JHOBM
7PMUBHFGPS3FNPUF
1PXFS
7EDN"NBYJNVN
3FQMBDFNFOU1BSUT
.JDSPQIPOF4UBOE"EBQUFS6-9
8"
"$"EBQUFS7"$)[
14
(SJQ4XJUDI$PWFS6-9
8"
"$"EBQUFS7"$)[
14"3
14";
;JQQFS#BH6-9
"
"$"EBQUFS7"$)[
;JQQFS#BH6-9
#
"$"EBQUFS7"$)[&VSPQMVH
14&
4DSFXESJWFS6-9
"
"$"EBQUFS7"$)[
146,
0QUJPOBM"DDFTTPSJFT
"$"EBQUFS7"$)[
14+
4.n$BSUSJEHFXJUI(SJMMF6-9
318
1BTTJWF"OUFOOB4QMJUUFS$PNCJOFS,JU
6"
#&5""n$BSUSJEHFXJUI(SJMMF6-9#&5"
318
6)'*O-JOF"OUFOOB"NQMJGJFS
6"6457
4.$BSUSJEHFXJUI(SJMMF6-94.
318
6)'1PXFSFE%JSFDUJPOBM"OUFOOB
6"6457
4."$BSUSJEHFXJUI(SJMMF6-9
318
6)'"OUFOOB1PXFS%JTUSJCVUJPO"NQMJGJFS64"
6"48#
#&5""$BSUSJEHFXJUI(SJMMF6-9#&5""
318
6)'"OUFOOB1PXFS%JTUSJCVUJPO"NQMJGJFS&VSPQF
6"48#&
#&5"$$BSUSJEHFXJUI(SJMMF6-9#&5"$
318
6)'"OUFOOB1PXFS%JTUSJCVUJPO"NQMJGJFS6,
6"48#6,
.BUUF4JMWFS(SJMMFGPS4.n
3,(
NGU
#/$ࣇ#/$DBCMF3(
6"
.BUUF4JMWFS(SJMMFGPS4.
31.
3,(
NGU
#/$ࣇ#/$DBCMF3(
6"
.BUUF4JMWFS(SJMMFGPS#&5""n
NGU
#/$ࣇ#/$$BCMF3(9
6"
.BUUF4JMWFS(SJMMFGPS#&5""
3,
NGU
#/$ࣇ#/$$BCMF3(9
6"
#MBDL(SJMMFGPS4."
3,(
NGU
#/$ࣇ#/$$BCMF3(
6"
#MBDL(SJMMFGPS#&5""
31.(
'PVS"OUFOOB3BDL1BOFM
6"
#MBDL(SJMMFGPS#&5""BOE#&5"$
31.(
'SPOU.PVOU"OUFOOB,JU*ODMVEFTDBCMFTBOECVMLIFBEBEBQU
FST
6"
#FMU$MJQ
""
8BWF"OUFOOB.)[
6"#
3FNPUF"OUFOOB#SBDLFUXJUI#/$#VMLIFBE"EBQUFS
6"
8BWF"OUFOOB.)[
6"
3BDL.PVOU"OUFOOB,JUGPSTJOHMF3FDFJWFS
6"
8BWF"OUFOOB.)[
6"-
3BDL.PVOU,JUGPS5XP3FDFJWFST
6"
8BWF"OUFOOB.)[
6"%
$BSSZJOH$BTF
8"
8BWF"OUFOOB.)[
6"2
.JDSPQIPOF"EBQUFS$BCMF9-3UP5"'
8"
8BWF"OUFOOB.)[
6"(
8BWF"OUFOOB.)[
6"&
8BWF"OUFOOB.)[
6"'
8BWF"OUFOOB.)[
6"+
6OJUFE4UBUFT$BOBEB-BUJO
"NFSJDB$BSJCCFBO
4IVSF*ODPSQPSBUFE
8FTU5PVIZ"WFOVF
/JMFT*-64"
1IPOF
'BY64"
'BY
&NBJMJOGP!TIVSFDPN
www.shure.com
i4IVSF*ODPSQPSBUFE
&VSPQF.JEEMF&BTU"GSJDB
4IVSF&VSPQF(NC)
+BLPC%JFGGFOCBDIFS4US
&QQJOHFO(FSNBOZ
1IPOF
'BY
&NBJMJOGP!TIVSFEF
"TJB1BDJGJD
4IVSF"TJB-JNJUFE
',JOH࣐T3PBE
/PSUI1PJOU*TMBOE&BTU
)POH,POH
1IPOF
'BY
&NBJMJOGP!TIVSFDPNIL
ITEM 7
Model UA844SWB User Guide
MODEL UA844SWB ANTENNA DISTRIBUTION SYSTEM
RÉPARTITEUR D'ANTENNE MODÈLE UA844SWB
ANTENNENVERTEILERSYSTEM MODELL UA844SWB
SISTEMA DE DISTRIBUCION DE ANTENAS MODELO UA844SWB
SISTEMA DI DISTRIBUZIONE AD ANTENNE MODELLO UA844SWB
MODELO UA844SWB SISTEMA DA DISTRIBUIçãO DA ANTENAS
©2009 Shure Incorporated
27C8744 (Rev. 3)
Printed in U.S.A.
MODEL UA844SWB ANTENNA DISTRIBUTION SYSTEM
OPTIONAL ACCESSORIES
The Shure Model UA844SWB is a UHF antenna distribution system that allows the expansion of wireless microphone systems by
splitting one pair of antennas to multiple receivers. It also amplifies
RF signals to compensate for insertion loss that results from splitting signal power to multiple outputs. A single UA844SWB system
can support up to four wireless receivers. A maximum of five
UA844SWB systems may be used in a two-tiered configuration.
Refer to the illustration on page 11.
Line Amplifier (470-900 MHz) ....................................UA830WB
Line Amplifier (470-698 MHz) ................................UA830USTV
Line Amplifier (944-952 MHz) ....................................... UA830X
Powered Directional Antenna (470-900 MHz)...........UA870WB
Powered Directional Antenna (470-698 (MHz) ......UA870USTV
Powered Directional Antenna (944-952 MHz)............... UA870X
1/2 Wave Antenna (774-862 MHz)................................ UA820A
1/2 Wave Antenna (690-746 MHz)................................ UA820B
1/2 Wave Antenna (554-590 MHz)................................UA820D
1/2 Wave Antenna (470-530 MHz)................................UA820G
1/2 Wave Antenna (944-952 MHz)................................ UA820X
2 ft. BNC-BNC Cable ...................................................... UA802
6 ft. BNC-BNC Cable ...................................................... UA806
25 ft. BNC-BNC Cable .................................................... UA825
50 ft. BNC-BNC Cable ................................................... UA850
100 ft. BNC-BNC Cable ................................................ UA8100
SYSTEM COMPONENTS
•
•
•
•
•
Front-mounting antenna hardware
Rack-mounting hardware
External power supply
Antenna cables for receiver connections
DC power cables for receiver connections
SPECIFICATIONS
REPLACEMENT PARTS
Carrier Frequency Range
470-952 MHz
Distributed RF Output Level (Gain)
-0.5 to 3 dB, 1 dB typical, from antenna input (unused ports terminated with 50 :)
Output Connector Isolation
30 dB, typical
Third Order Intercept Point (3 OIP)
21 dBm, typical
DC Input Voltage
14 to 18 Vdc
DC Output Voltage
14 to 18 Vdc, 4 connectors
Maximun Current Supply from DC Outputs
1.5 Amps
DC Antenna Voltage
12 Vdc
Impedance
50 :
RF Input/Output Antenna Connector Type
BNC
Operating Temperature Range
-7q C to 49q C (20q to 120q F)
Overall Dimensions
44.5 mm H x 482.6 mm W x 171.5 mm D (1.75 x 19 x 6.75 in.)
Net Weight
1.62 Kg (3.6 lbs)
Certification
UA844SWB: Authorized under the Declaration of Conformity
provision of FCC Part 15. Certified under Industry Canada to
RSS-123 (IC: 616A-UA844SWB). Conforms to European ETSI
standards EN 301 489, Parts 1 and 9. Meets the essential requirements of the European R&TTE Directive 99/5/EC; eligible
to carry the CE marking.
PS45US: Conforms to safety standard IEC 60065.
PS45E: Conforms to safety standard IEC 60065.
PS45UK: Conforms to safety standard IEC 60065.
Hardware Kit ............................................................. 90XN1371
Bulkhead Adapters....................................................... 95A8994
Power Cables for SLX Receivers................................. 95B8373
Power Cables for ULX Receivers ................................ 95B8420
Power Supply................................................................PS45US
Power Supply.................................................................. PS45E
Power Supply................................................................PS45UK
LICENSING INFORMATION
Note that a ministerial license to operate this equipment may be required in certain areas. Consult your national authority for possible
requirements.
Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate the equipment. Licensing
of Shure wireless microphone equipment is the user's responsibility,
and licensability depends on the user's classification and application, and on the selected frequency. Shure strongly urges the user
to contact the appropriate telecommunications authority concerning
proper licensing, and before choosing and ordering frequencies.
IMPORTANT: THIS RADIO EQUIPMENT IS INTENDED FOR
USE IN PROFESSIONAL ENTERTAINMENT (CLASS I) AND
SIMILAR APPLICATIONS.
NOTE: THIS EQUIPMENT MAY BE CAPABLE OF OPERATING
ON SOME FREQUENCIES NOT AUTHORIZED IN YOUR
REGION. PLEASE CONTACT YOUR NATIONAL AUTHORITY
TO OBTAIN INFORMATION ON AUTHORIZED FREQUENCIES
FOR WIRELESS MICROPHONE PRODUCTS IN YOUR
REGION.
2
ITEM 8
Personal PA® FM Listening System • Model PPA 377
Personal PA® FM Listening System • Model PPA 377
Description:
The PPA 377 features the T35 high performance transmitter: powerful microprocessor, sleek digital
display, easy-to-use menu controls. The T35 configures itself to the appropriate setting,
taking the guesswork out of complicated audio installation. Operating up to 1000 feet, the T35 is
ideal for auditoriums, theaters or other large venues where excellent coverage area is essential.
System includes four impact-resistant PPA R37 single-channel receivers. The PPA R37 receiver will
operate up to 50 hours for long-lasting performance!
Applications:
• Churches • Schools • Auditoriums • Conference Rooms • Theaters
PPA T35 Transmitter:
Dimensions, Weight:
Color:
Rack Mount:
Power:
Temperature Range:
Operating Freqs:
Frequency Accuracy:
Deviation:
Pre-Emphasis:
RF Field Strength:
Nominal Range:
Audio Proc. Functions:
Frequency Response:
Signal-to-Noise Ratio:
8.45" (21.5 cm) W x 8.18" (20.8 cm) D x 1.72" (4.4 cm) H, 3.1 lbs (1.4 kg)
Black with white legends
One EIA rack space high, 1/2 space wide
1–2 units can be mounted in a single rack space with optional RPK 005 (single) or RPK 006
(double) Rack Mount Kits
Wall mount Class II transformer (TFP 016)
Input: 120 VAC, 60 Hz, 17 W
Output: 24 VAC, 500 mA with 3-pin Molex® plug
Approvals: UL, CSA listed
Operating:0° C to 40° C (+32° F to +104° F)
Storage:-20° C to 70° C (-4° F to +158° F)
72.1-75.9 MHz* , 17 wideband channels (selectable), 72.025-75.975 MHz, 77 narrowband channels (selectable)
±.005% stability, 0-50˚ C
Wideband: ± 75 kHz maximum. Narrowband: ± 5 kHz maximum.
Wideband: 75 μsec. Narrowband: 300 μsec
Does not exceed 80 mV/m at 3 m
Up to 1000 ft (304 m) Note: Maximum transmitter range is achieved using the ANT 005 coaxial
antenna
Reduced or Normal Compressor Gain
Compression Slope Control
High Pass and Low Pass Filter Frequency control
22 – 16000 Hz, +1, -3 dB (adjustable)
74 dB transmitted
*DISCLAIMER: FCC RULES LIMIT USE OF THIS EQUIPMENT TO AUDITORY ASSISTANCE.
T35 Front Panel:
NOTE: SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
©2011 Williams Sound, LLC CAT 100I
1
Personal PA® FM Listening System • Model PPA 377
Personal PA® FM Listening System • Model PPA 377
Audio Level Control:
Audio Level Indicators:
Power On Indicator:
Phones Output:
Audio Input:
Line Output:
LCD Menu Controls:
(Push-Button Selection)
Push-button audio level controls, adjustable to 0 to -50 dB
10 LED array that reads +9 to -18 at 3 dB intervals
Green LED indicates power on
Mono signal, 1/4" TRS stereo jack, 67 mW, maximum in 50 ohms (adjustable 0 to -40 dB)
Combination 3-pin XLR, 1/4" TRS jack
RCA jack, -10 dBV (.32 VRMS) output, impedance 100 Ω
Applications Presets (Music, Voice, Hearing Assist)
Bandwidth, Frequency, Audio Input Source (Microphone, Line, Simplex), High Pass Filter, Low Pass
Filter, Compressor Slope, Compressor Gain, RF Output Power
T35 Rear Panel:
Input Levels (Bal or Unbal):
Microphone Simplex-Mic:
Line:
Simplex Mode:
RF “Off” Timer:
Common Mode Rejection:
Total Harmonic Distortion:
Approvals:
Warranty:
Nominal (1st Amber LED)
Maximum (Input Overload LED) Absolute Maximum Ratings**
-60dBV (1 mV RMS)
-20 dBV (100 mV RMS)
+20dBV (10.0 V RMS)
-8dBV (400 mV RMS)
+16 dBV (6.3 V RMS)
+20 dB V (10.0 V RMS)
12 volts simplex power (DIN 45596) on the 3-pin XLR connector
Turns off RF signal after 1 hour of no audio activity
> 57 dB @ 1 kHz, Mic or Line
< 0.25% @ -10 dB V audio line output, 1 kHz
FCC, RoHS, WEEE
5 years, parts and labor*
**Note: Stresses above these ratings may cause permanent damage. Exposure for extended periods may degrade reliability.
*90 days on accessories.
NOTE: SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
©2011 Williams Sound, LLC CAT 100I
2
Personal PA® FM Listening System • Model PPA 377
Personal PA® FM Listening System • Model PPA 377
PPA R37 Receiver:
Dimensions:
Weight:
Color:
Battery Type:
Current Consumption:
Operating Freq.:
FM Deviation:
De-Emphasis:
LED Indicator:
Sensitivity:
Input Overload:
Frequency Response:
Signal-to-Noise Ratio:
Receiver Antenna:
Audio Output:
Output Connector:
Approvals:
Warranty:
4.1" L x 2.85" W x 1.38” D (104 mm x 72 mm x 35 mm)
4.6 oz (130 g) with batteries, 2.6 oz w/o batteries (73g)
Black
Two (2) AA non-rechargeable alkaline batteries (BAT
001), approx. 48 hours battery life, or
Two (2) AA rechargeable NiMH batteries (BAT 026), 1600
mAh, approx 30 hours battery life
Nominal 52 mA
17 channels: 72.1, 72.2, 72.3, 72.4, 72.5, 72.6, 72.7, 72.8,
72.9, 74.7, 75.3, 75.4, 75.5, 75.6, 75.7, 75.8 or 75.9 MHz*.
+75 kHz
75 μS
Power: Bright Green. Low Battery: Flashes.
2 μV at 12 dB Sinad with squelch defeated
100 mV
200 Hz to 15 kHz, ± 3 dB
65 dB at 100 μV
Integral with earphone/headphone cord
35 mW, max. 16 ohm load
3.5 mm stereo phone jack, accepts either stereo or mono
plug
FCC, Industrie Canada, RoHS, WEEE
Five years, parts and labor. 90 days on cords, earphones,
headphones, batteries and other accessories
*DISCLAIMER: FCC RULES LIMIT USE OF THIS EQUIPMENT TO “AUDITORY ASSISTANCE
FOR THE HANDICAPPED.”
This device complies to “RSS-Gen Issue 2 June 2007” for Industry Canada and FCC part
15.105(b) for the United States.
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
This device complies with ICES-003 class B. Test data is available from the manufacturer
on request.
NOTE: SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
©2011 Williams Sound, LLC CAT 100I
3
Personal PA® FM Listening System • Model PPA 377
Personal PA® FM Listening System • Model PPA 377
Bid Specs:
The PPA T35 transmitter shall be microprocessor controlled with push button configuration. It shall have an
operating range of up to 1000 feet. It shall have 17 wideband channels operating on 72.1–75.9 MHz. It shall
have 77 narrowband channels operating on 72.025–75.975 MHz.
Front Panel:
The PPA T35 shall have a push button controlled LCD digital display. There shall be three pre-configured (selectable) application presets: Hearing Assist, Music and Voice. Configurations for Bandwidth, Frequency, Audio
Input Source (Microphone, Line, Simplex), High Pass Filter, Low Pass Filter, Compressor Slope, Compressor Gain
and RF Output Power shall be push button controlled. The audio level shall be adjustable by push button control. There shall be a 10 LED array showing audio level from +9 to -18 at 3dB intervals. The PPA T35 shall have a
1/4" phone jack with push button volume control. It shall have push button control for monitoring source
audio or transmitted audio. It shall have an input overload indicator. It shall have an “on” indicator and power
button.
Rear Panel:
The PPA T35 shall be powered by 24 VAC power supply via a 3-pin Molex® connector. It shall have a 75 ohm
F-connector antenna. It shall have an ANT 025 whip antenna on the top panel directly connected to the circuit
board. The transmitter shall have an RCA line output jack. It shall have a combination 1/4" phone/XLR audio
input jack. It shall have an RF “Off” timer that turns off RF signal after 1 hour of no audio activity.
The PPA T35 shall have FCC, be compliant with RoHS and WEEE regulations and be powered by UL and CSA
power supply. It shall have a 5-year parts and labor warranty. It shall be compatible with Williams Sound FM
equipment operating on 72-76 MHz. The transmitter shall be a Williams Sound model number PPA T35.
PPA R37 Receiver:
The PPA R37 receiver shall be encased in black, PC/ABS impact-resistant plastic with a hinged battery
door. The receiver shall be a body-pack style and include a detachable belt-clip for hands-free operation.
Receiver shall have a 3.5mm stereo/mono jack to accommodate stereo or mono low impedance earphones, headphones and neckloops. Receiver shall have a combination volume control with power
on/off rotary dial. It shall have a green LED indicating battery and system status codes. The PPA R37
shall have access to 17 wideband channels between 72-76MHz. Channel selection shall be made by pushing the seek button inside the battery compartment. Receiver shall have channel-lock capability.
Receiver shall have a slide switch inside the battery compartment to select Alkaline or rechargeable
NiMH rechargeable battery operation. It shall have charger contacts on the bottom of the receiver for
use with Williams Sound drop-in chargers CHG 3512 and CHG 3502. The PPA R37 shall operate up to 48
hrs with two AA Alkaline batteries, and up to 30 hrs with two AA NiMH rechargeable batteries (BAT
026).
Receiver shall provide a maximum out of 35mW at 16 ohms with an earbud-type earphone. The system’s
audio frequency response shall be 200Hz to 15kHz ± 3dB and the signal-to-noise ratio shall be 65dB min.
The receiver sensitivity shall be 2μV or better at 12dB Sinad with squelch defeated. The PPA R37 shall
accept up to ±75kHz FM deviation and have a 75μs de-emphasis time constant.
The PPA R37 shall have FCC, Industrie Canada approvals and be compliant with RoHS and WEEE regulations. The receiver shall be covered by a five-year parts and labor warranty, excluding earphones, headphones and batteries.
*90 days on accessories.
NOTE: SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
©2011 Williams Sound, LLC CAT 100I
4
Personal PA® FM Listening System • Model PPA 377
Personal PA® FM Listening System • Model PPA 377
Contact:
Domestic Sales
Williams Sound
10300 Valley View Rd.
Eden Prairie, MN 55344
Ph: 800-328-6190 / 952-943-2252
FAX: 952-943-2174
Email: info@williamssound.com
Web: www.williamssound.com
International Sales
International Sales Department
Williams Sound
10300 Valley View Rd.
Eden Prairie, MN 55344 USA
Phone: +1 952 224 7791
Fax: +1 952 943 2174
Email: info@williamssound.com
Web: www.williamssound.com
NOTE: SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
©2011 Williams Sound, LLC CAT 100I
5
ITEM 9
FM
SPECIFICATION DATA
PPA R37
PPA Select™ FM Receiver
The NEW PPA Select FM receiver features easy-to-use, seekbutton channel selection with access to 17 pre-set wideband
frequencies between 72-76 MHz. Digitally synthesized for even
greater audio clarity and stability, the PPA Select also offers
channel-lock capability (to prevent accidental channel change)
and a battery-saving Sleep Mode. A versatile 3.5mm stereo/mono
jack allows for a variety of earphone and headphone options, and
is neckloop/telecoil-equipped-hearing-aid compatible. The stylish,
impact-resistant PPA Select single-channel receiver is compatible
with any Williams Sound Personal PA transmitter operating on the
72-76 MHz bandwidth. The PPA Select includes two AA alkaline
batteries for up to 50 hours of long-lasting operation.
© 2011, Williams Sound, LLC MCAT 098B
PPA Select™ FM Receiver
PPA Select™ Receiver
,(97/65,
1(*2
Dimensions:
Weight:
Color:
Battery Type:
OFF
Battery Life:
656--=63<4,
*65;963:>0;*/
65
36>)(;;,9@
-3(:/*6+,
05+0*(;69
4.1” x 2.85” x 1.38” (104 x 72 x 35mm)
4.6oz (130g) with batteries. 2.6oz (73g) without batteries
Black
(2) AA Alkaline or 2 x AA NiMH
Two (2) AA non-rechargeable alkaline batteries (BAT 001), approx. 50 hrs
(2) AA rechargeable NiMH batteries (BAT 026), 1500 mAh, approx. 32 hrs
Current Consumption:
Temperature Range:
Channels
Operating Freq.:
52mA nominal
17, accessed via seek button in battery compartment
72.1, 72.2, 72.3, 72.4, 72.5, 72.6, 72.7, 72.8, 72.9, 74.7, 75.3, 75.4, 75.5,
75.6, 75.7, 75.8, 75.9 MHz*
Intermediate Freq.:
75 kHz
FM Deviation:
75 kHz
De-Emphasis:
75 μS
LED Indicator:
Power: Green; Low Battery: Flashes Green
AFC Range:
Sensitivity:
Input Overload:
Frequency Response:
Modulation:
Signal-to-Noise Ratio:
Receive Antenna:
± 120 kHz
2 μV at 12 dB Sinad with squelch defeated
100 mV
200 – 15 kHz
FM, +/- 75 kHz peak deviation
65 dB min @ 100 uV
Integral with earphone/headphone cord
Audio Output:
35 mW max, peak into 16 ohms
Output Connector:
3.5 mm stereo/mono phone jack
OQ<
Earphone:
Auto Shut-off
Approvals:
Warranty:
!"#$%&'$%<=
>?J'
J$K
"$$
Lifetime PLUS Limited Warranty, 90 Days on most accessories.
*DISCLAIMER: FCC RULES LIMIT USE OF THIS EQUIPMENT TO AUDITORY ASSISTANCE
NOTE: SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE!
© 2011, Williams Sound, LLC MCAT 098B
PPA Select™ FM Receiver
Bid Specs:
RR%X
Y
Z$R[\!
resistant plastic with a hinged battery door. The receiver shall be
a body-pack style and include a detachable belt-clip for handsfree operation. The receiver shall have a 3.5mm stereo/mono jack
to accommodate stereo or mono low impedance earphones,
headphones and neckloops. The receiver shall have a combination
volume control with power on/off rotator dial. It shall have a green
]^'
""&%X
have access to 17 preset wideband channels between 72-76MHz.
"'Z
the battery compartment. The receiver shall have channel-lock
capability.
The receiver shall provide a maximum out of 35mW at 16ø with
an earbud type earphone. The systems audio frequency response
shall be 200Hz to 15kHz ± 3dB and the signal to noise ratio shall
be 65dB min. The receiver sensitivity shall be 2μV or better at 12dB
#`&%X{XZ|
FM deviation and have a 75 μ s de-emphasis time constant.
%XYJ$K
"
Y
#
'&
Y
covered by a Lifetime PLUS Limited Warranty, 90 Days on most
accessories.
Y
RR%X&
The receiver shall have a slide switch inside the battery
compartment to select disposable Alkaline or NiMH rechargeable
battery operation. It shall have charger contacts on the bottom of
Y
#
!
'
_
%O<_%<&%X
#
two disposable AA Alkaline batteries and up to 32 hours with two
AA NiMH rechargeable batteries (BAT 026).
Domestic Sales
Williams Sound
O%}"}#
Eden Prairie, MN 55344
Ph: 800-328-6190 / 952-943-2252
FAX: 952-943-2174
Email: info@williamssound.com
Web: www.williamssound.com
International Sales
International Sales Department
Williams Sound
O%}"}#
Eden Prairie, MN 55344 USA
Phone: +1 952 943 2252
Fax: +1 952 943 2174
Email: info@williamssound.com
Web: www.williamssound.com
800.843.3544 / info@williamssound.com / www.williamssound.com
© 2011, Williams Sound, LLC MCAT 098B
ITEM 10
ITEM 11
SPECIFICATION DATA
^
Plug
Cord length
%„
Impedance
O?Š
Frequency Range
Max input power
}
Sensitivity
O<ƒ\‡OZ|
O%
Replacement earpad
K
^
O%}"}#
R
$€%QQˆ
R‚‰O„<„Q%<<<
J>‚‰O„<„Q%<OXQ
‚‡#&
‚###&#&
<!<Z|
Driver size
Weight
O%}"}#
R
$€%QQ
R‚ƒ!%<ƒ!?O„[„<!„Q%!<<<
J†‚„<!„Q%!<OXQ
‚‡#&
‚###&#&
%&€
OQ'
O
ƒ&ƒQ%&%QQ[‡#&[###&#&
<OO$$]]€O<
ITEM 12
Multiple Battery Charger • Models CHG 3512 and CHG 3512 PRO
Multiple Battery Charger • Models CHG 3512 and CHG 3512 PRO
Description:
This multi-unit, drop-in style charger will conveniently store and charge up to 12 Williams Sound
R35, R35-8, R863, RX22-4 receivers, or T863 transmitters over the course of a 16 hour time span. It helps
keep your products organized and saves cost on having to replace alkaline batteries.
CHG 3512, CHG 3512 PRO Multiple Battery Charger:
CHG 3512:
(charger only)
Size: 9.5”L x 7.4”W x 1.7”H (24.1 cm L x 18.8 cm W x 4.3 cm H)
Weight: 1.2 lbs (.54 kg), excluding power supply
CHG 3512 PRO:
(charger in case)
Size: 18”L x 14”W x 6.75”H (45.7 cm L x 35.5 cm W x 17.1 cm H)
Weight: 10 lbs (4.53 kg)
Color:
Power Supply Input:
Power Supply:
Charging Rate:
Black ABS
90 - 240 VAC input
TFP 037 Switching AC adapter, 5 VDC - 4A output
16 Hour Charge: 140 mA
Pulse/Maintain: 140 mA
16 hours nominal
12 Units
Individual Charging Indicators: Red LEDs. LEDs blink when batteries are charged
1 year (cables and power supply warrantied for 90 days)
CE, WEEE, RoHS
Charging specifications are based on Williams Sound Corp. rechargeable NiMH battery, BAT 026 (1400 mAh)
Charging Time:
Unit Capacity:
Indicators:
Warranty:
Approvals:
Note:
CHG 3512: Charger only
CHG 3512 PRO: Charger in case
CHG 3512
Front-Top View
CHG 3512
Rear View
CHG
WARNING: DO
NOT ATTEMPT
TO RECHARGE
DISPOSABLE BATT
ERIES!
CHG
Williams Soun
d
Williams Soun
d
CHG
Receiver or
Transmitter
CHG
Charging LED
Indicator
CHG
WARNING: DO
NOT ATTE
MPT TO RECHAR
GE DISPOSABLE
BATTERIES!
CHG
TFP 035
AC Power Connection
NOTE: SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE!
©2007, Williams Sound Corp. MCAT 035E
1
Multiple Battery Charger • Models CHG 3512 and CHG 3512 PRO
Multiple Battery Charger • Models CHG 3512 and CHG 3512 PRO
Bid Specs:
The CHG 3512 shall be a 12 unit drop-in battery charger and shall charge a maximum of 24 AA size NiMH
batteries while they are installed into the Williams Sound Corp. PPA R35, PPA R35-8, R863, RX22-4 style 3V
receivers or T863 style 3V transmitter.
The charger CHG 3512 shall be microprocessor controlled and enclosed in ABS plastic measuring 9.5” L x
7.4” W x 1.7” H (24.1cm L x 18.8cm W x 4.3cm H). The CHG 3512 unit shall weigh 1.2 lbs (2.64 Kg) without
power supply, 2.9lbs (6.4 Kg) shipping weight. In the optional carry case, the charger shall weigh 10 lbs
(4.53 kg).
The charger shall be a timed charger at 16 hours, and will provide a maintain charge once the timer has
completed its charging cycle. Each bay on the charger shall have a red LED indicating charging status. The
LEDs shall be on constantly on during charging and will blink indicating when batteries are fully charged.
The charger CHG 3512 shall be powered by an external switching power supply (90-240 VAC input; 5 VDC,
4A output) via a CD barrel connector.
The charger shall have CE approval, and be compliant with RoHS and WEEE regulations.
The charger shall be the Williams Sound Corp. model CHG 3512.
NOTE: SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE!
©2007, Williams Sound Corp. MCAT 035E
2
Multiple Battery Charger • Models CHG 3512 and CHG 3512 PRO
Multiple Battery Charger • Models CHG 3512 and CHG 3512 PRO
Contact:
United States
Williams Sound Corp.
10321 W. 70th Street
Eden Prairie, MN 55344
Ph: 800-328-6190 / 952-943-2252
FAX: 952-943-2174
Email: info@williamssound.com
Web: www.williamssound.com
Canada
Thorvin Electronics
2861 Sherwood Heights Dr. Units 36-37
Oakville, ON L6J-7K1 Canada
Ph: 800-323-6634 / 905-829-3040
FAX: 905-829-4196
Web: www.thorvinelectronics.com
South America
DPTech
SIA Trecho 3/4 Lote 335 2°. Andar
71200-030 Brasília, DF
BRAZIL
Phone: (5561) 361-1384
Fax: (5561) 361-0948
Web: www.dptech.com.br
Email: ws@dptech.com.br
United Kingdom
Sound Associates
Keeble House, 81 Island Farm Road
West Molesey, Surrey KT 2SA
United Kingdom
Phone: (44) 020 8939 5900
Fax: (44) 020 8939 5901
Web: www.soundassociates.co.uk
Email: jmurdoch@soundassociates.com
Asia, Europe, Australia, Latin America, Middle East, South Africa
International Sales Department
Williams Sound Corp.
10321 W. 70th Street
Eden Prairie, MN 55344 USA
Phone: +1 952 224 7791
Fax: +1 952 943 2174
Email: info@williamssound.com
Web: www.williamssound.com
NOTE: SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE!
©2007, Williams Sound Corp. MCAT 035E
3
ITEM 13
DATASHEET
PS-8R II
POWER CONDITIONER/SEQUENCER WITH SMP+ TECHNOLOGY
UNPARALLELED POWER PURIFICATION AND PROTECTION
FEATURES
• Series Multi-Stage Protection Plus ( SMP+) for virtually maintenance free protection from surges and spikes. No sacrificed parts,
no service calls, no downtime!
• Furmanʼs unequaled Linear Filtering Technology ( LiFT) rids systems of AC line noise for consistent audio/video clarity
• Automatic Extreme Voltage Shutdown ( E.V.S.) powers down equipment during a prolonged or extreme over-voltage
• Six sequenced rear panel outlets (in 3 groups), two switched rear panel outlets, and one front panel unswitched outlet
• Momentary and Maintained sequencing via rear panel terminal block or front panel switch
• BNC connector on the rear panel allows attachment of any standard 12V gooseneck lamp to illuminate the rear of your rack
• 15 amp rating
• 3 year limited warranty
DESCRIPTION
The most widely recognized and trusted name in AC power
conditioning is proud to introduce the PS-8R II power
conditioner / sequencer, featuring Furmanʼs revolutionary
SMP+ technology. Furmanʼs Series Multi-Stage Protection
Plus (SMP+) circuit features our exclusive Linear Filtering
Technology (LiFT) and Extreme Voltage Shutdown (E.V.S.).
Together, these technologies comprise what is, without question,
the worldʼs most advanced and comprehensive transient voltage
surge suppressor.
Additionally, the PS-8R II Power Conditioner/Sequencer is
capable of powering up a rack full of equipment in a 3-step
delayed sequence. The sequence is reversed for power-down. The
sequence can be initiated with either momentary or maintained
switches, locally or remotely. A duplex outlet is provided for
each delay step. A front panel screwdriver adjustment sets the
delay time for the PS-8R II. The PS-8R II also features a locking
switch with a removable key for maximum security. One or
more Furman PS-8R IIʼs may be installed in remote locations and
operated via low-voltage wiring. The PS-8R II includes a rear
mounted BNC jack which accepts any standard (12VAC, 0.5A)
gooseneck lamp for rear rack illumination, as well as a front panel
switch which controls the gooseneckʼs operation.
PS-REL Relay Accessory
Allows a PS-8R II to be turned on by sensing AC at a
preampʼs switched outlet; also allows daisy-chaining for
6 or more delayed outlet groups.
Export Models
Models PS-8R E II: “E” suffix versions are for use in countries
with 220/240 volt AC lines. Furman Power Sequencers use
internationally accepted IEC-320 connectors.
(Continued on reverse)
PS-8R II
Series Multi-Stage Protection Plus (SMP+)
SMP+ is Furmanʼs proprietary surge suppression and noise
filtration system. Designed over a period of two years by our
California based engineering team, SMP+ is composed of
three separate and distinct technologies which work together
in a precisely tuned circuit to filter or “clean” the incoming
power and to protect connected equipment from potentially
damaging AC events. These technologies are Linear Filtering,
Series Multi-Stage Protection, and Extreme Voltage Shutdown.
Linear Filtering Technology (LiFT):
Unfortunately, traditional AC filter conditioners have been
designed for unrealistic laboratory conditions. Prior technologies
could actually harm audio and video performance more than
they help, due to the resonant peaking of their antiquated, nonlinear designs. Under certain conditions, these designs can
actually add more than 10 dB of noise to the incoming AC line!
Worse still, lost digital data, the need to re-boot digital pre-sets, or
destroyed digital converters are frequently caused by excessive
voltage spikes and AC noise contaminating the equipment ground.
Furmanʼs LiFT takes another approach, ensuring optimal
performance through linear filtering and no leakage to ground.
PS-8R II SPECIFICATIONS
Current Rating
15 amps (“E” version 10 amps)
Operating Voltage
90 to 140 VAC (“E” version 180 to 280 VAC)
Over Voltage Shutdown
140 VAC typically (“E” version 280 VAC typically)
Spike Protection Modes
Series Multi-Stage Protection (SMP):
Traditional surge suppression relies on circuits that “sacrifice”
themselves when exposed to multiple transient voltage spikes,
requiring the dismantling of your system and repair of your surge
suppressor. With Furmanʼs SMP+, however, damaging transient
voltages are safely absorbed, clamped and dissipated. No sacrificed
parts, no service calls, no downtime. Also unique to Furmanʼs
SMP+ is its unparalleled clamping voltage. While other designs
offer clamping voltages that are well above 300Vpk, Furmanʼs
SMP+ clamps at 188Vpk, 133 VAC RMS, even when tested with
multiple 6000Vpk - 3000 amp surges! This unprecedented level
of protection is only available with Furmanʼs SMP+ technology.
Extreme Voltage Shutdown (E.V.S.):
When voltage rises to extreme levels because of a lost neutral
line or an accidental connection to 208 or 240 VAC, Furmanʼs
Extreme Voltage Shutdown kicks in, automatically powering down
all equipment quickly and safely in order to prevent damage
from occurring. An indicator LED will then illuminate, alerting
you to the situation until the over voltage condition is corrected.
Noise Attenuation
10 dB @ 10 kHz
40 dB @ 100 kHz
100 dB @ 10 MHz
Linear attenuation curve from 0.05 - 100 ohms line impedance
Dimensions
19” W x 10.5” D x 1.75” H
Weight
11 lbs (5 kg)
Power Consumption
6 watts
Line to neutral, zero ground leakage
Safety Agency Listings
Spike Clamping Voltage
188 Vpk @ 3,000 amps, 133 VAC RMS
(tested to UL-1449 6,000 Vpk @ 3,000 amps)
Response Time
1 nanosecond
Maximum Surge Current
CE, NRTL-C
Patent Number
CA1332074 (4,901,183)
Three Year Limited Warranty
The PS-8R II is protected by a limited three year warranty
covering defects in materials and workmanship.
6,500 amps
Fu r m a n S o u nd, L LC • 1690 Co r po r a te Circ l e • Peta l um a , CA. 94954 USA • Phone: (707) 763-1010 • Fax: (707) 763-1310 • w w w.Furma n S o u n d. co m
© 2006 Furman Sound, LLC. All rights reserved. 051006
ITEM 14
C D i
S E R I E S
CDi Series
he CDi Series of Crown® amplifiers are
professional tools designed and built for
installed sound applications. The series
includes four models which are identical
except for output power: CDi 1000, CDi 2000,
CDi 4000 and CDi 6000. All are rugged and
lightweight, and offer unmatched value in
their class.
CDi-Series amplifiers feature an intuitive
front-panel LCD screen to guide installers
through their configurations. CDi amplifiers
also offer onboard DSP for loudspeaker
signal processing. Other features include a
switch-mode universal power supply, useful
function indicators, proportional-speed fanassisted cooling, removable Phoenix-style
inputs, barrier strip outputs for low-Z or
70V/100V/140V loads, short-circuit protection
and more.
T
Your investment in a CDi-Series amplifier is
backed by Crown’s Three-Year, No-Fault, Fully
Transferable Warranty.
For more details about the Crown CDi Series,
contact the Crown Technical Support Group at
800-342-6939 or 574-294-8200. Also, visit the
Crown Audio website at www.crownaudio.com.
CDi 1000
1 kHz
Power
Features
Accurate, uncolored sound with very low
distortion for the best in music and voice reproduction
•
Switch-mode universal power supply
•
Onboard digital signal processing includes
crossovers, EQ filters, delay, and output limiting
•
Extremely versatile; rated for 2, 4, 8 ohm loads
and 70V/100V and 140V outputs
•
All products fill 2U rack spaces and weigh under
19 pounds
•
Advanced protection circuitry guards against:
shorted outputs, open circuits, DC, mismatched loads, general overheating, high-frequency overloads and internal faults
•
Barrier strip outputs for low-Z or 70V/100V/
140V loads, removable Phoenix-style inputs
•
Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and
guarantees its specifications
•
•
Intuitive front-panel LCD screen for quick,
easy configuration
Specifications
Output Power: See power charts below.
Voltage Gain at 1kHz:
CDi 1000: 30.5 dB
CDi 2000: 32.9 dB
CDi 4000: 34.2 dB
CDi 6000: 37.1 dB
Frequency Response: +0/–1 dB from 20 Hz to
20 kHz at 1 watt into 4 ohms.
CDi 4000
1 kHz
Power
2 ohm Dual (per channel)
700W*
2 ohm Dual (per channel)
1,600W*
4 ohm Dual (per channel)
500W
4 ohm Dual (per channel)
1,200W
8 ohm Dual (per channel)
275W
8 ohm Dual (per channel)
650W
4 ohm Bridge-Mono
1,400W*
4 ohm Bridge-Mono
3,200W*
70V Dual (per channel)
500W
70V Dual (per channel)
1,000W
100V** Dual (per channel)
500W
100V** Dual (per channel)
1,000W
140V Bridge-Mono
**100Vp
CDi 2000
1,000W
With 0.5% THD.
*With 1% THD.
1 kHz
Power
140V Bridge-Mono
**100Vp
CDi 6000
2,000W
With 0.5% THD.
*With 1% THD.
1 kHz
Power
2 ohm Dual (per channel)
1,000W*
2 ohm Dual (per channel)
3,000W*
4 ohm Dual (per channel)
800W
4 ohm Dual (per channel)
2,100W
8 ohm Dual (per channel)
475W
8 ohm Dual (per channel)
1,200W
4 ohm Bridge-Mono
6,000W*
70V Dual (per channel)
2,500W
100V** Dual (per channel)
2,500W
4 ohm Bridge-Mono
2,000W*
70V Dual (per channel)
800W
100V** Dual (per channel)
800W
140V Bridge-Mono
**100Vp
1,600W
With 0.5% THD.
*With 1% THD.
140V Bridge-Mono
**100Vp
5,000W
With 0.5% THD.
*With 1% THD.
Load Impedance: Safe with all types of loads.
Rated for 2 to 8 ohms in Stereo mode, 4 to 16
ohms in Bridge-Mono mode. CDi 1000 A1 (100V
version) is rated for 4 to 8 ohms in Stereo mode,
8 to 16 ohms in Bridge-Mono mode.
Sensitivity:
At 8 ohm rated output:
CDi 1000: 1.4V
CDi 2000: 1.4V
CDi 4000: 1.4V
CDi 6000: 1.4V
At 4 ohm rated output:
CDi 1000: 1.3V
CDi 2000: 1.2V
CDi 4000: 1.3V
CDi 6000: 1.3V
At 2 ohm rated output:
CDi 1000: 1.1V
CDi 2000: 1.0V
CDi 4000: 1.0V
CDi 6000: 1.1V
Signal to Noise Ratio (below rated 8-ohm
power at 1 kHz): CDi 1K, 2K, 4K: 100 dB (A
weighted). CDi 6K: 103 dB (A weighted).
Damping Factor: Better than 500 from 20 Hz
to 400 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to
1 kHz, A-weighted.
Input Stage: Input is electronically balanced
and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced; 10 k ohms, unbalanced.
AC Line Voltage and Frequency Configurations
Available: 100V, 120V, 220-240V, 50/60 Hz.
AC Line Current (120VAC amplifier playing 1/8
power pink noise into 4 ohms per ch):
CDi 1000: 6.8A, CDi 2000: 8.3A, CDi 4000:
10.5A; at idle draws no more than 38 watts.
CDi 6000: 15.3A; at idle draws no more than
180 watts.
CDi 1000 | 1200W
CDi 2000 | 1225W
CDi 4000 | 1250W
CDi Series
CDi 1000, 2000, 4000 back panel
Output Connectors: 4-position barrier strip
with connectors for dual louspeakers or bridgemono loudspeaker.
HiQnet USB Connector: Type B, connects to a
HiQnet network.
HD-15 Connector: For cinema I/O compatibility
with CDi-8M System Monitor. See Figure 1.
AR
Y
CDi 6000 back panel
Protection
Input EQ: 6 parametric filters per channel with
adjustable Q, ±15 dB boost/cut. Also adjustable
high and low shelving filters. This 8-filter EQ
section can be bypassed.
Crossover Filters: Highpass and lowpass per
channel. Butterworth 6/12/18/24 dB per octave, Linkwitz-Riley 24/48 dB per octave. Also
includes ±15 dB bandpass gain and polarity
control.
PR
EL
Output EQ: 8 parametric filters per channel with
adjustable Q, ±15 dB boost/cut. This 8-filter
EQ section can NOT be bypassed. Filters are
enabled individually.
Output Limiter: Prevents clipping and protects
loudspeakers. Choice of –3, –6, or –12 dB
threshold per channel.
Delay: Up to 50 msec total delay per channel.
Presets: 20 presets. One is “DSP OFF.” Fifteen
are factory-set for JBL Cinema systems. Four
are user-definable.
IN
DSP Section
Sel/Prev/Next Buttons: Three buttons near the
LCD screen are used to access menu items and
front panel lockout.
LCD Screen: Backlit liquid crystal display
shows speaker presets and signal processing.
Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is
present at input.
–10 Indicator: Green LED flashes when output
signal exceeds –10 dB below clip.
–20 Indicator: Green LED flashes when output
signal level exceeds –20 dB below clip.
Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to
produce audio.
Clip Indicator: Red LED, one per channel, turns
on at the threshold of audible distortion.
Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions.
Power Indicator: Blue LED illuminates when the
amplifier has been turned on and has power.
IM
Maximum Input Signal: +22 dBu typical.
Operating Temperature: 0° C to 40° C at 95%
relative humidity (non-condensing).
Front Panel Controls and Indicators
Level: Detented rotary level control, one per
channel.
Power Switch: On/off switch applies AC power
to the amplifier.
CDi-Series amplifiers are protected against
shorted, open or mismatched loads; overloaded
power supplies; excessive temperature; chain
destruction phenomena; excessive output
current, and input overload damage. They also
protect loudspeakers from input/output DC,
large or dangerous DC offsets and turn-on/
turn-off transients
Construction
Chassis: Steel.
Cooling: Proportional speed fan with front-torear airflow.
Dimensions: EIA Standard 19-in. rack mount
width (EIA RS-310-B), 3.5 in. (8.9 cm) high and
12.25 in. (31.11 cm) deep behind mounting
surface. CDi 6000 is 16.2 in. (41.15 cm) deep.
Net Weight:
CDi 1K. 2K, 4K: 19 lb (8.6 kg).
CDi 6K: 24 lb (10.9 kg).
Shipping Weight:
CDi 1K, 2K, 4K: 22 lb (10.0 kg).
CDi 6K: 30 lb (13.6 kg).
Rear Panel Controls and Connectors
AC Line Connector:
CDi 1K, 2K, 4K: NEMA 5-15P (15A).
CDi 6000: NEMA 6-10P (20A)
IEC C20 (20A).
Input Connector: Two 3-pin removable Phoenix-type connectors each accept a balanced
line-level input signal.
Crown’s Three-Year, No-Fault, Fully Transferable Warranty
Crown offers a Three-Year, No-Fault, Fully Transferable Warranty for every new Crown amplifier—an unsurpassed industry standard. With this unprecedented No-Fault protection, your new
Crown amplifier is warranted to meet or exceed original specifications for the first three years of
ownership. During this time, if your amplifier fails, or does not perform to original specifications,
it will be repaired or replaced at our expense. About the only things not covered by this warranty
are those losses normally covered by insurance and those caused by intentional abuse. And the
coverage is transferable, should you sell your amplifier.
See your authorized Crown dealer for full warranty disclosure and details. For customers outside
of the USA, please contact your authorized Crown distributor for warranty information or call
574-294-8200.
Crown International
1718 W. Mishawaka Rd.
Elkhart, IN 46517-9439
TEL:574-294-8200
FAX: 574-294-8FAX
www.crownaudio.com
Specifications subject to change without prior notice. Latest
information available at www.crownaudio.com.
Crown, Crown Audio and Macro-Tech are registered
trademarks of Crown International. Other trademarks are the
®
property of their respective owners. ©2007 Crown Audio ,
Inc. Printed in U.S.A.
5/09
139648-4
ITEM 15
C D i
S E R I E S
CDi Series
he CDi Series of Crown® amplifiers are
professional tools designed and built for
installed sound applications. The series
includes four models which are identical
except for output power: CDi 1000, CDi 2000,
CDi 4000 and CDi 6000. All are rugged and
lightweight, and offer unmatched value in
their class.
CDi-Series amplifiers feature an intuitive
front-panel LCD screen to guide installers
through their configurations. CDi amplifiers
also offer onboard DSP for loudspeaker
signal processing. Other features include a
switch-mode universal power supply, useful
function indicators, proportional-speed fanassisted cooling, removable Phoenix-style
inputs, barrier strip outputs for low-Z or
70V/100V/140V loads, short-circuit protection
and more.
T
Your investment in a CDi-Series amplifier is
backed by Crown’s Three-Year, No-Fault, Fully
Transferable Warranty.
For more details about the Crown CDi Series,
contact the Crown Technical Support Group at
800-342-6939 or 574-294-8200. Also, visit the
Crown Audio website at www.crownaudio.com.
CDi 1000
1 kHz
Power
Features
Accurate, uncolored sound with very low
distortion for the best in music and voice reproduction
•
Switch-mode universal power supply
•
Onboard digital signal processing includes
crossovers, EQ filters, delay, and output limiting
•
Extremely versatile; rated for 2, 4, 8 ohm loads
and 70V/100V and 140V outputs
•
All products fill 2U rack spaces and weigh under
19 pounds
•
Advanced protection circuitry guards against:
shorted outputs, open circuits, DC, mismatched loads, general overheating, high-frequency overloads and internal faults
•
Barrier strip outputs for low-Z or 70V/100V/
140V loads, removable Phoenix-style inputs
•
Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and
guarantees its specifications
•
•
Intuitive front-panel LCD screen for quick,
easy configuration
Specifications
Output Power: See power charts below.
Voltage Gain at 1kHz:
CDi 1000: 30.5 dB
CDi 2000: 32.9 dB
CDi 4000: 34.2 dB
CDi 6000: 37.1 dB
Frequency Response: +0/–1 dB from 20 Hz to
20 kHz at 1 watt into 4 ohms.
CDi 4000
1 kHz
Power
2 ohm Dual (per channel)
700W*
2 ohm Dual (per channel)
1,600W*
4 ohm Dual (per channel)
500W
4 ohm Dual (per channel)
1,200W
8 ohm Dual (per channel)
275W
8 ohm Dual (per channel)
650W
4 ohm Bridge-Mono
1,400W*
4 ohm Bridge-Mono
3,200W*
70V Dual (per channel)
500W
70V Dual (per channel)
1,000W
100V** Dual (per channel)
500W
100V** Dual (per channel)
1,000W
140V Bridge-Mono
**100Vp
CDi 2000
1,000W
With 0.5% THD.
*With 1% THD.
1 kHz
Power
140V Bridge-Mono
**100Vp
CDi 6000
2,000W
With 0.5% THD.
*With 1% THD.
1 kHz
Power
2 ohm Dual (per channel)
1,000W*
2 ohm Dual (per channel)
3,000W*
4 ohm Dual (per channel)
800W
4 ohm Dual (per channel)
2,100W
8 ohm Dual (per channel)
475W
8 ohm Dual (per channel)
1,200W
4 ohm Bridge-Mono
6,000W*
70V Dual (per channel)
2,500W
100V** Dual (per channel)
2,500W
4 ohm Bridge-Mono
2,000W*
70V Dual (per channel)
800W
100V** Dual (per channel)
800W
140V Bridge-Mono
**100Vp
1,600W
With 0.5% THD.
*With 1% THD.
140V Bridge-Mono
**100Vp
5,000W
With 0.5% THD.
*With 1% THD.
Load Impedance: Safe with all types of loads.
Rated for 2 to 8 ohms in Stereo mode, 4 to 16
ohms in Bridge-Mono mode. CDi 1000 A1 (100V
version) is rated for 4 to 8 ohms in Stereo mode,
8 to 16 ohms in Bridge-Mono mode.
Sensitivity:
At 8 ohm rated output:
CDi 1000: 1.4V
CDi 2000: 1.4V
CDi 4000: 1.4V
CDi 6000: 1.4V
At 4 ohm rated output:
CDi 1000: 1.3V
CDi 2000: 1.2V
CDi 4000: 1.3V
CDi 6000: 1.3V
At 2 ohm rated output:
CDi 1000: 1.1V
CDi 2000: 1.0V
CDi 4000: 1.0V
CDi 6000: 1.1V
Signal to Noise Ratio (below rated 8-ohm
power at 1 kHz): CDi 1K, 2K, 4K: 100 dB (A
weighted). CDi 6K: 103 dB (A weighted).
Damping Factor: Better than 500 from 20 Hz
to 400 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to
1 kHz, A-weighted.
Input Stage: Input is electronically balanced
and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced; 10 k ohms, unbalanced.
AC Line Voltage and Frequency Configurations
Available: 100V, 120V, 220-240V, 50/60 Hz.
AC Line Current (120VAC amplifier playing 1/8
power pink noise into 4 ohms per ch):
CDi 1000: 6.8A, CDi 2000: 8.3A, CDi 4000:
10.5A; at idle draws no more than 38 watts.
CDi 6000: 15.3A; at idle draws no more than
180 watts.
CDi 1000 | 1200W
CDi 2000 | 1225W
CDi 4000 | 1250W
CDi Series
CDi 1000, 2000, 4000 back panel
Output Connectors: 4-position barrier strip
with connectors for dual louspeakers or bridgemono loudspeaker.
HiQnet USB Connector: Type B, connects to a
HiQnet network.
HD-15 Connector: For cinema I/O compatibility
with CDi-8M System Monitor. See Figure 1.
AR
Y
CDi 6000 back panel
Protection
Input EQ: 6 parametric filters per channel with
adjustable Q, ±15 dB boost/cut. Also adjustable
high and low shelving filters. This 8-filter EQ
section can be bypassed.
Crossover Filters: Highpass and lowpass per
channel. Butterworth 6/12/18/24 dB per octave, Linkwitz-Riley 24/48 dB per octave. Also
includes ±15 dB bandpass gain and polarity
control.
PR
EL
Output EQ: 8 parametric filters per channel with
adjustable Q, ±15 dB boost/cut. This 8-filter
EQ section can NOT be bypassed. Filters are
enabled individually.
Output Limiter: Prevents clipping and protects
loudspeakers. Choice of –3, –6, or –12 dB
threshold per channel.
Delay: Up to 50 msec total delay per channel.
Presets: 20 presets. One is “DSP OFF.” Fifteen
are factory-set for JBL Cinema systems. Four
are user-definable.
IN
DSP Section
Sel/Prev/Next Buttons: Three buttons near the
LCD screen are used to access menu items and
front panel lockout.
LCD Screen: Backlit liquid crystal display
shows speaker presets and signal processing.
Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is
present at input.
–10 Indicator: Green LED flashes when output
signal exceeds –10 dB below clip.
–20 Indicator: Green LED flashes when output
signal level exceeds –20 dB below clip.
Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to
produce audio.
Clip Indicator: Red LED, one per channel, turns
on at the threshold of audible distortion.
Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions.
Power Indicator: Blue LED illuminates when the
amplifier has been turned on and has power.
IM
Maximum Input Signal: +22 dBu typical.
Operating Temperature: 0° C to 40° C at 95%
relative humidity (non-condensing).
Front Panel Controls and Indicators
Level: Detented rotary level control, one per
channel.
Power Switch: On/off switch applies AC power
to the amplifier.
CDi-Series amplifiers are protected against
shorted, open or mismatched loads; overloaded
power supplies; excessive temperature; chain
destruction phenomena; excessive output
current, and input overload damage. They also
protect loudspeakers from input/output DC,
large or dangerous DC offsets and turn-on/
turn-off transients
Construction
Chassis: Steel.
Cooling: Proportional speed fan with front-torear airflow.
Dimensions: EIA Standard 19-in. rack mount
width (EIA RS-310-B), 3.5 in. (8.9 cm) high and
12.25 in. (31.11 cm) deep behind mounting
surface. CDi 6000 is 16.2 in. (41.15 cm) deep.
Net Weight:
CDi 1K. 2K, 4K: 19 lb (8.6 kg).
CDi 6K: 24 lb (10.9 kg).
Shipping Weight:
CDi 1K, 2K, 4K: 22 lb (10.0 kg).
CDi 6K: 30 lb (13.6 kg).
Rear Panel Controls and Connectors
AC Line Connector:
CDi 1K, 2K, 4K: NEMA 5-15P (15A).
CDi 6000: NEMA 6-10P (20A)
IEC C20 (20A).
Input Connector: Two 3-pin removable Phoenix-type connectors each accept a balanced
line-level input signal.
Crown’s Three-Year, No-Fault, Fully Transferable Warranty
Crown offers a Three-Year, No-Fault, Fully Transferable Warranty for every new Crown amplifier—an unsurpassed industry standard. With this unprecedented No-Fault protection, your new
Crown amplifier is warranted to meet or exceed original specifications for the first three years of
ownership. During this time, if your amplifier fails, or does not perform to original specifications,
it will be repaired or replaced at our expense. About the only things not covered by this warranty
are those losses normally covered by insurance and those caused by intentional abuse. And the
coverage is transferable, should you sell your amplifier.
See your authorized Crown dealer for full warranty disclosure and details. For customers outside
of the USA, please contact your authorized Crown distributor for warranty information or call
574-294-8200.
Crown International
1718 W. Mishawaka Rd.
Elkhart, IN 46517-9439
TEL:574-294-8200
FAX: 574-294-8FAX
www.crownaudio.com
Specifications subject to change without prior notice. Latest
information available at www.crownaudio.com.
Crown, Crown Audio and Macro-Tech are registered
trademarks of Crown International. Other trademarks are the
®
property of their respective owners. ©2007 Crown Audio ,
Inc. Printed in U.S.A.
5/09
139648-4
ITEM 16
96-038 / rev 11c / 06-01-10
ERK Series Enclosure
®
Middle Atlantic Products
EIA/TIA Compliant
SEISMIC CERTIFIED
EXCEPTIONAL SUPPORT & PROTECTION™
The ERK Series 19” welded stand-alone / gangable enclosures.
Advanced manufacturing techniques provide highest quality
and lowest price.
Features
• Fully welded construction
• 2,500 lb. weight capacity
• 1/8" thick structural steel internal braces
• UL Listed in the US and Canada
• Seismic certified (when used with ERK-Z4 option) with an Ip value of 1.5
• 22” OD width, available 20” or 25” OD depth
• 1/2" , 3/4", 1” & 1-1/2" electrical knockouts on removable split rear plates top and bottom,
easily removable for cable pass-through. Top plates additionally include UHF / VHF knockouts
• Standard front, optional rear 11-gauge 10-32 threaded, fully adjustable rackrail with
numbered rackspace increments
• Keylocked solid rear door standard, optional vented rear doors available
• Optional front doors available
• Configurable top options on 44, 40, and 35 space sizes
ERK-4425
• Durable black textured powder coat finish
Architects’ and Engineers’ Specifications
OPTIONS
• Front doors shall be reinforced 16-gauge steel, model #FD-XX (solid), VFD-XX
(vented, 22% open area), LVFD-xx (vented 63% open area-not available for 27
space rack) PVFD-44 (vented plexi), (X=# of rackspaces of ERK rack)
• Vented rear doors shall be 16-gauge steel & available as model #ERK-VRD-XX,
(X=# of rackspaces of ERK rack)
• Top panels for 35, 40 or 44 space ERK, 16-gauge steel, multiple styles available
including model #ERK-ST (solid), ERK-10FT (10” fan), ERK-6FT (two 6” fans)
ERK-4FT (three 4-1/2” fans), ERK-VT (vented) and ERK-LVT (large perf vented)
see A&E spec 96-01063 for more details
• Caster base, four casters shall have a total weight capacity of 1300 pounds, model
# CBS-ERK-YY (Y= cabinet depth)
• Rear rail kit, 11-gauge, 10-32 threaded, sold in pairs, hardware included, model
#ERK-RRXX (X=# of rackspaces)
• Seismic compliancy floor anchor kit, model # ERK-Z4
• 18, 21 and 27 space ERK come preconfigured with solid top that includes knockouts
to accommodate up to two 4-1/2” fans, or included vent panels
• Grommet for 4” electrical knockout in side of ERK shall be model # GK4
and include 4 pieces
• Gland grommet for 4” electrical knockout in side of ERK shall be model #GK-4G. 4 Pieces.
• Slide out option available (See AXS Spec sheet 96-055S)
C U S T O M I Z A B L E S P E C I F I C AT I O N C L I P S A VA I L A B L E AT M I D D L E AT L A N T I C . C O M
US: New Jersey • California • Illinois • Voice: 973-839-1011 Fax: 973-839-1976 • middleatlantic.com
Canada: Ontario • British Columbia • Voice: 613-836-2501 Fax: 613-836-2690 • middleatlantic.ca
96-038 / rev 11c / 06-01-10 / ERK Series Enclosure
EIA compliant 19” stand-alone / gangable equipment rack shall be Middle Atlantic Products model #
ERK-__-__(see chart for available models). Overall dimensions of rack shall be __”H x __”W x
__”D (refer to chart). Useable height shall be __ rackspaces, useable depth shall be __” (refer to
chart). Rack shall be of fully welded construction. Weight capacity shall be 2,500 lbs. Rack shall be
constructed of the following materials: top and bottom shall be 16-gauge steel, horizontal braces shall
be 16-gauge steel welded to integral structural side panels of 16-gauge steel giving an 1/8” thick
structure, rear door shall be 18-gauge steel, all structural elements shall be finished in a durable black
powder coat. Rack shall come equipped with one pair of fully adjustable 11-gauge steel rackrail with
tapped 10-32 mounting holes in universal EIA spacing, black e-coat finish and numbered rackspaces.
Rack shall include solid locking rear door standard and solid side panels with vertical slotted vent pattern
at top and bottom (and laser knockouts for cable pass-through on 44, 40, and 35 space models). Top
and bottom of rack shall feature vertical slotted vent pattern. Rack shall have removable split rear
knockout panels with 1/2”, 3/4”, 1”, and 1-1/2” electrical knockouts installed in base and a
removable rear knockout panel with 1/2”, 3/4”, 1”, and 1-1/2” electrical knockouts and BNC
knockouts for UHF/VHF antennae installed in top. Grounding and bonding stud shall be 1/4-20
threaded, installed in base of enclosure. ERK series racks shall satisfy the 1997 UBC and 2001 CBC
Seismic Zone 4 and the 2000 IBC, 2003 IBC, 2002 ASCE Standard 7 and 2003 NFPA 5000 Seismic Use
Group III lateral force requirements for protecting 600 lbs. of essential equipment in upper floor
installations when used in conjunction with the ERK-Z4 floor anchor brackets. Rack shall be UL Listed in
the US and Canada. Rack shall be GREENGUARD Indoor Air Quality Certified for Children and Schools.
Rack shall be RoHS EU Directive 2002/95/EC compliant. Rack shall be manufactured by an ISO 9001
and ISO 14001 registered company. Rack shall be warrantied to be free from defects in material or
workmanship under normal use and conditions for the lifetime of the product.
ERK Configured A/V Enclosure
®
EIA/TIA Compliant
SEISMIC CERTIFIED
Configured A/V enclosure ships complete with the
most commonly used accessories
Includes
• Integrated fan top
• Configurable rear door with bottom vent, solid locking front door
• 3-1/4” wide vertical lacer strip (height varies based on model)
• Six horizontal lacer bars
• Twelve 8” Velcro® cable management straps
• Thin power strip, 20 Amp, 20 outlet with cord (44 space enclosures)
or 2 qty. thin power strip, 20 Amp, 10 outlet with cord (35 & 40 space
enclosures)
• Leveling feet
• 100 qty. 10-32 mounting hardware
25 ”
ERK-4425-AV
Architects’ and Engineers’ Specifications
EIA compliant 19” stand-alone equipment rack shall be Middle Atlantic Products model # ERK-__-AV
knockouts for UHF/VHF antennae. ERK Series enclosures shall satisfy the 1997 UBC and 2001
(refer to chart). Overall dimensions of rack shall be __" H x 22" W x 25" D. Useable height shall be __
CBC Seismic Zone 4 and the 2000 IBC, 2003 IBC, 2002 ASCE Standard 7 and 2003 Ed. NFPA
rackspaces, useable depth shall be 23-1/2". Fully welded construction shall provide a 2,500 lb. weight
5000 Seismic Use Group III lateral force requirements for protecting 600 lbs. of essential
capacity. Rack shall be constructed of the following materials: top and bottom shall be 16-gauge steel,
equipment in upper floor installations when used in conjunction with the ERK-Z4 seismic floor
horizontal braces shall be 16-gauge steel welded to integral structural side panels of 16-gauge steel
anchor brackets with an Ip value of 1.5. ERK-__-AV shall include a high-density thin power
giving an 1/8" thick structure. Solid front door shall be 18-gauge steel and rear door shall be 18-gauge
distribution and shall be Middle Atlantic Products model # PDT-____-NS with __ outlets and
steel and all structural elements shall be finished in a durable black powder coat. Rack shall come
20 amps (refer to chart). Thin power distribution shall be ____” long (refer to chart) x 1” deep
equipped with one pair of 11-gauge steel rackrail with tapped 10-32 mounting holes in universal EIA
x 1.9” wide. J-Box shall be 2” deep x 2” wide. Thin power distribution shall feature __ NEMA
spacing, black e-coat finish and numbered rackspaces. Rack shall include 100 qty. 10-32 mounting
5-20R outlets. Corded power strip includes 20 amp protection and mounting hardware. Corded
screws. Rack shall be equipped with one 3-1/4” vertical lacer strip Middle Atlantic Products model #
model shall beterminated with 10-foot power cord and a NEMA 5-20P plug. PDT Series shall
LACE-__-OP (refer to chart), four ‘L’ shaped straight and two 4” offset horizontal lacer bars and twelve,
feature a black anodized finish. ERK and PDT Series shall be UL Listed in the US and Canada.
8” Velcro® straps for cable management. The ERK shall have a solid locking rear door standard and
ERK-__-AV shall be GREENGUARD Indoor Air Quality Certified for Children and Schools. ERK-__-
solid side panels with vertical slotted vent pattern at top and bottom with laser knockouts for cable
AV shall be RoHS EU Directive 2002/95/EC compliant. ERK-__-AV shall be manufactured by an
pass-through. Top and bottom of rack shall feature vertical slotted vent pattern. Rack shall have feature
ISO 9001 and ISO 14001 registered company. PDT series shall be warrantied to be free from
integrated fan top, Middle Atlantic Products model # ERK-4FT-285CFM for active thermal management.
defects in materials or workmanship for a period of 3 years. ERK enclosure shall be warrantied
The ERK-4FT-285CFM shall consist of three 4-1/2” fans and airflow shall be 285 CFM. Rack shall have
to be free from defects in material or workmanship under normal use and conditions for the
removable split rear knockout panels with 1/2”, 3/4”, 1” and 1-1/2” electrical knockouts and top BNC
lifetime of the rack.
US: New Jersey • California • Illinois • Voice: 973-839-1011 Fax: 973-839-1976 • middleatlantic.com
Canada: Ontario • British Columbia • Voice: 613-836-2501 Fax: 613-836-2690 • middleatlantic.ca
2.13
[54]
REAR VIEW, TOP & BOTTOM
E
laser knockouts
for 4” electrical
tubing on
ERK-35, 40 &44
Four 11/32” dia.
laser knockouts
for ganging on
ERK-35, 40 &44
8.41
[213]
A
12.38
[314]
1” [25] & 1-1/2” [38] EKO
1.50 [38]
removable EKO plates
20.00
[508]
3.50
[89]
6.00
[152]
12.00
[305]
Laser knockouts
for 4-1/2” fans
REAR
BOTTOM VIEW
mounting holes
ERK-XX20=10.41 [264]
ERK-XX25=15.41 [391]
2.00 [51]
typical front
22.00 [559]
B
19.25
[489]
REAR VIEW SIDE VIEW FRONT VIEW
5/8” [16] dia. KO
1/2” [13] dia. “D” KO
(UHF/VHF Antenna KO)
1/2” [13] & 3/4” [19] EKO
1” [25] & 1-1/2” [38] EKO
ERK basic dimensions
5.94 [151]
.78 [20]
1.50 [38]
3.44 [87]
1.50 [38]
22.00
[559]
TOP VIEW OF ERK SIDE
SECTIONAL VIEW
C
1.50 [38]
9.80 [249]
1/4 - 20 X 1”
[25] grounding and
bonding stud
(1 place only)
EKO’s
1/2” [13] &
3/4” [19]
1” [25] &
1-1/2” [38]
3.00 [76]
typical rear
fully adjustable
10-32 threaded
rackrail
front door clearance
(with rackrail in
forward-most position)
1.44 [37] solid/vented door
1.25 [32] plexi door
D
BOTTOM VIEW
All dimensions in inches unless otherwise noted [All dimensions in brackets are in millimeters]
22.00
[557]
TOP VIEW
ERK-35XX
ERK-40XX
ERK-44XX
TOP VIEW
ERK-18XX
ERK-21XX
ERK-27XX
Middle Atlantic Products
19.50
[495]
FRONT
0.41 [10] (4 places)
4.80 [122]
US: New Jersey • California • Illinois • Voice: 973-839-1011 Fax: 973-839-1976 • middleatlantic.com
Canada: Ontario • British Columbia • Voice: 613-836-2501 Fax: 613-836-2690 • middleatlantic.ca
Part #
ERK-4425
ERK-4025
ERK-3525
ERK-2725
ERK-2125
ERK-1825
ERK-4420
ERK-4020
ERK-3520
ERK-2720
ERK-2120
ERK-1820
ERK-4425-AV
ERK-4025-AV
ERK-3525-AV
A
Overall
Height
81.125 [2061]
74.125 [1883]
65.375 [1661]
51.375 [1305]
40.875 [1038]
35.625 [905]
81.125 [2061]
74.125 [1883]
65.375 [1661]
51.375 [1305]
40.875 [1038]
35.625 [905]
81.125 [2061]
74.125 [1883]
65.375 [1661]
B
Useable
Height
77.125 [1959]
70.125 [1781]
61.375 [1559]
47.375 [1203]
36.875 [937]
31.625 [803]
77.125 [1959]
70.125 [1781]
61.375 [1559]
47.375 [1203]
36.875 [937]
31.625 [803]
77.125 [1959]
70.125 [1781]
61.375 [1559]
C
Rear
Height
75.125 [1908]
68.125 [1703]
59.375 [1508]
45.375 [1153]
34.875 [886]
29.625 [752]
75.125 [1908]
68.125 [1703]
59.375 [1508]
45.375 [1153]
34.875 [886]
29.625 [752]
75.125 [1908]
68.125 [1703]
59.375 [1508]
D
Overall
Depth
25.00 [635]
25.00 [635]
25.00 [635]
25.00 [635]
25.00 [635]
25.00 [635]
20.00 [508]
20.00 [508]
20.00 [508]
20.00 [508]
20.00 [508]
20.00 [508]
25.00 [635]
25.00 [635]
25.00 [635]
E
Bottom Opening
Depth
20.25 [514]
20.25 [514]
20.25 [514]
20.25 [514]
20.25 [514]
20.25 [514]
15.25 [387]
15.25 [387]
15.25 [387]
15.25 [387]
15.25 [387]
15.25 [387]
20.25 [514]
20.25 [514]
20.25 [514]
TOP OPTIONS
ERK-10FT
accepts 10” fan
ERK-6FT
accepts two 6” fans
ERK-4FT accepts
three 4-1/2” fans
ERK-10FT- 550CFM
includes 10” fan
ERK-6FT- 440CFM
includes two 6” fans
ERK-4FT- 285CFM
includes three
4-1/2” fans
(included in A/V
enclosures)
ERK-10FT-FC
includes 10” fan and
fan controller
ERK-4QFT-FC
includes 4-1/2”
quiet fans and fan
controller
ERK-ST
solid
Rack Part #
ERK-4025-AV /
ERK-3525-AV
ERK-4425-AV
ERK-VT
slot vent
ERK-LVT
large perf vent
ERK A/V Enclosure Power Distribution
Terminated
Circuit
Outlets
Part #
Overall Length
Qty
PDT-1020C-NS
5-20P
20 Amp
10, 5-20R
37.75 [959]
2
PDT-2020C-NS
5-20P
20 Amp
20, 5-20R
72.75 [1848]
1
Part #
ERK-4425-AV
ERK-4025-AV
ERK-3525-AV
ERK A/V Enclosure Vertical Lacer Bar Chart
Lacer Bar
Number of Rackspaces
LACE-44-OP
44
LACE-40-OP
40
LACE-37-OP
37
Width
3.25 [83]
3.25 [83]
3.25 [83]
US: New Jersey • California • Illinois • Voice: 973-839-1011 Fax: 973-839-1976 • middleatlantic.com
Canada: Ontario • British Columbia • Voice: 613-836-2501 Fax: 613-836-2690 • middleatlantic.ca
ITEM 17
96-01105 / rev. 1b / 08-23-10
UD Series Utility Drawers
EXCEPTIONAL SUPPORT & PROTECTION™
The UD Series rackmount utility drawers offer an economical
storage solution for any enclosure
Features
• Full extension ball bearing slides extend a full 14”
UD1 shown as
a writing surface
• Durable black powder coat finish
• Keylock and latch option for security, user-installed
(2, 3 and 4 space drawers only)
• Cable entry point at the rear of the drawer allows
for optimized cable management
• Four sizes available
UD1
• UL Listed in the US and Canada
Architects and Engineers’ Specifications
EIA compliant 19” rackmount drawer shall be Middle Atlantic Products model # UD_
(refer to chart). Drawer shall have useable width of __”, a useable surface of __” and
occupy __ rackspaces (refer to chart). Drawer base shall be __-gauge steel, top and
sides shall be __-gauge steel (refer to chart). Drawer faceplate shall be __-gauge steel
with a black powder coat finish (refer to chart). Drawer shall extend __” (refer to chart).
Drawer shall use full extension, ball bearing slides. UD__ shall have cable entry point
at the rear of the drawer. UD__ shall have a knockout on the face of the drawer to
accommodate optional user-installed latch and keylock (refer to chart). Drawer shall have
mounting hole spacing of __” (refer to chart). Drawer shall have a 50 lb. weight capacity.
Drawer shall be UL Listed in the US and Canada. Drawer shall be GREENGUARD Indoor Air
Quality Certified for Children and Schools. Drawer shall be RoHS EU Directive 2002/95/
EC compliant. Drawer shall be manufactured by an ISO 9001 and ISO 14001 registered
company. Drawer shall be warrantied to be free from defects in materials or workmanship
under normal use and conditions for a period of three years.
OPTIONS
• User installed latch for UD Series drawers shall be Middle Atlantic Products model
# LATCH. LATCH shall fit 2, 3 and 4 space drawers.
• User installed keylock for UD Series drawers shall be Middle Atlantic Products model
# KYLK. KYLK shall fit 2, 3 and 4 space drawers.
• Additional set of keys for KYLK shall be Middle Atlantic Products model # ACC-KEY.
• No-slip drawer mat for UD Series drawers shall be Middle Atlantic Products
model #DM.
C U S T O M I Z A B L E S P E C I F I C AT I O N C L I P S AVA I L A B L E AT M I D D L E AT L A N T I C . C O M
US: New Jersey • California • Illinois • Voice: 973-839-1011 Fax: 973-839-1976 • middleatlantic.com
Canada: Ontario • British Columbia • Voice: 613-836-2501 Fax: 613-836-2690 • middleatlantic.ca
96-01105 / rev. 1b / 08-23-10 / UD Series Utility Drawers
UD3
UD basic dimensions
All dimensions in inches unless otherwise noted [All dimensions in brackets are in millimeters]
UD1
‰*
<\}\$^
!"#$%
*#<#$
>?!>@$JJ\>^?"^?<@#\<
_@#`?\$<^#<{|
!"#$%

#<#$>?!>
>!#@$JJ\>^
?"^?<@#\<
‚
‚
$@?!~?
@$>„!}?
‚
`>!ƒ?>
?"^?<@#\<

$@?!~?ƒ#`^€
*
UD2, UD3, UD4
<\}\$^„\>?…\}
_J!>^†‡ˆ|
\>!^}€_J!>^†ˆ!^}€|
Š‹\$<^#<{€\?@J!}#<{
Š‹
€?#{€^
*
‚
`>!ƒ?>
?"^?<@#\<
‚
$@?!~?
@$>„!}?
}!~?J!@@^€>$
‚
$@?!~?ƒ#`^€
Part #
“A”
Racking
Height
“B”
Mounting
Hole Spacing
“C”
Useable
Width
“D”
Usable
Surface
“E”
Drawer
Extension
Optional
Latch/
Keylock
Steel Gauge
Top & Sides
Steel Gauge Steel Gauge
Bottom
Front
UD1
1.75” (44) 1 space
1.25 (32)
15.93 (405)
13.43 (341)
14.00 (356)
No
20-gauge
20-gauge
20-gauge
UD2
3.50” (89) 2 space
3.00 (76)
15.97 (406)
14.56 (370)
14.56 (370)
Yes
16-gauge
20-gauge
18-gauge
UD3
5.25” (133) 3 space
2.25 (57)
15.97 (406)
14.56 (370)
14.56 (370)
Yes
16-gauge
20-gauge
18-gauge
UD4
7.00” (178) 4 space
4.00 (102)
15.97 (406)
14.56 (370)
14.56 (370)
Yes
16-gauge
20-gauge
18-gauge
US: New Jersey • California • Illinois • Voice: 973-839-1011 Fax: 973-839-1976 • middleatlantic.com
Canada: Ontario • British Columbia • Voice: 613-836-2501 Fax: 613-836-2690 • middleatlantic.ca
ITEM 18
I-00002
96-939/ rev 5 / 05-15-08
Middle Atlantic Products, Inc.
115 Volt Rackmount Power Strips
middleatlantic.com
EIA/TIA Compliant
Rackmount units provide economical
15 and 20 amp power distribution PD-915R / PD-915RC-20 / PD-920R-NS / PD-920R / PD-920RC-20
front view
Features
PD-815R-PL
front view
• UL Listed (file #E204950)
PD-915R-PL
• Available in 15 and 20 amp models
front view
• 8 circuit breaker protected rear outlets
PD-815RA-PL
• Enhanced surge protection with no surge diversion to ground
(PD-915, PD-920 and PD-815 Series only)
front view
• Two models available with front outlet and illuminated power
switch or pilot light for status indication
PD-815RC-PL
• Choice of finishes available: Black Brushed and Anodized,
Silver Brushed and Anodized, Black Powdercoat
front view
• Select models available with 20’ power cords
15 amp - rear view
Architects’ and Engineers’ Specifications
Rackmount power strip shall be Middle Atlantic Products model # __ (refer to
chart), with a __ amp power capacity (refer to chart), differential and common
mode surge and spike protection (surge and spike protection available on 15
amp power only) and EMI filtering. Enhanced surge protection with no surge
diversion to ground (PD-915, PD-920 and PD-815 series only). Rackmount
power strip shall operate on 115 volt AC/60Hz current. Rackmount power strip
shall include __' (refer to chart) 14/3 power cord with __ plug (refer to chart),
8 rear outlets (refer to chart), __ front outlet (s)(refer to chart), and __ amp
circuit breaker located on the power strip’s __ (refer to chart). Rackmount
power strip shall occupy one rackspace and be constructed of 18-gauge
phosphate pre-treated steel with a __finish (refer to chart). Rackmount power
strip shall be warranted to be free from defects in materials and workmanship
under normal use and conditions for a period of 3 years. Rackmount power
strip shall be UL listed in US and Canada.
c u sto mizab le sp e c ific atio n c lip s availab le at mid d le atlantic . c o m
Exceptional Support & Protection Products
US: New Jersey • California • Illinois • Voice: 973-839-1011 Fax: 973-839-1976 • middleatlantic.com
Canada: Ontario • British Columbia • Voice: 613-836-2501 Fax: 613-836-2690 • middleatlantic.ca
96-939 / rev 5 / 05-15-08 / 115 Volt Rackmount Power Strips
20 amp - rear view
Rackmount Power Strips basic dimensions
All dimensions in inches [Bracketed dimensions are in millimeters]
TOP VIEW
8.75
[222]
FRONT VIEW
(PD-815RA-PL / PD815RC-PL)
REAR VIEW
1.75
[44]
19.00 [483]
(PD-920R-NS, PD-920R, PD-920RC-20)
(PD-920R-NS,, PD-915R, PD-915RC-20, PD-920R, PD-920RC-20)
(PD-815R-PL)
(PD-815R-PL / PD-815RA-PL / PD815RC-PL)
PD-915R-PL
115 VOLT
(
(PD-915R)
(PD-915R-PL)
Part #
PD-815R-PL
PD-815RA-PL
PD-815RC-PL
PD-915R
PD-920R-NS
PD-915R-PL
PD-920R
PD-920RC-20
PD-915RC-20
15 AMP
60 HZ
Amps
15
15
15
15
20
15
20
20
15
Power Cord Type
NEMA 5-15P
NEMA 5-15P
NEMA 5-15P
NEMA 5-15P
NEMA 5-20P
NEMA 5-15P
NEMA 5-20P
NEMA 5-20P
NEMA 5-15P
# Front
Outlets
0
0
0
1
1
1
1
1
1
# Rear
Outlets
8
8
8
8
8
8
8
8
8
Circuit
Breaker
Location
Rear
Rear
Rear
Front
Rear
Rear
Front
Front
Front
Rear Outlet
Type
NEMA 5-15R
NEMA 5-15R
NEMA 5-15R
NEMA 5-15R
NEMA 5-20R
NEMA 5-15R
NEMA 5-20P
NEMA 5-20P
NEMA 5-15R
Cord
Length
9'
9'
9'
9'
9'
9'
9'
20'
20'
Finish
Black Powdercoat
Black Brushed and Anodized
Silver Brushed and Anodized
Black Powdercoat
Black Powdercoat
Silver Brushed and Anodized
Black Powdercoat
Black Powdercoat
Black Powdercoat
Surge Suppression & EMI Filter Specifications (PD-815R-PL / PD-815RA-PL / PD-815RC-PL / PD-915R)
• Nominal line voltage: 120 VAC
• Maximum line current: 15 Amps
• Maximum allowable voltage: 125 VAC (RMS)
- Maximum continuous voltage differential applied between
line and neutral
- Maximum clamping voltage: 395 volts@100 amps
• Peak impulse current (8/20 micro seconds):
- 30,000 amps, one time
- 21,000 amps, two times within 5 minutes
- 9,000 amps, ten times within 2 minutes
- Maximum peak impulse current pulse as defined between
line and neutral
- Maximum multiple impulse current derated per spec
• Response time: Instantaneous (Less than 1 nanosecond)
• EMI/ RF Suppression: More than 20 db
- Calculated line to neutral, 100 KHz to 1 MHz suppression
based upon nominal impedance
Middle Atlantic Products, Inc.
US: New Jersey • California • Illinois • Voice: 973-839-1011 Fax: 973-839-1976 • middleatlantic.com
Canada: Ontario • British Columbia • Voice: 613-836-2501 Fax: 613-836-2690 • middleatlantic.ca
ITEM 19
Technical Data Sheet
RG8/U Coaxial 50 Ohm - Plenum
2833 West Chestnut Street
Washington, PA 15301
Toll Free: (800) 245-4964
Fax: (724) 222-6420
www.westpenn-wpw.com
PART NUMBER:
25810
DESCRIPTION:
RG8/U – 1 Conductor 12 AWG 7x20, 95% Bare copper braid and an overall Copolymer Jacket.
NEC RATING:
CMP
APPROVALS:
(UL) C(UL) Listed
APPLICATION:
Indoor Plenum for: 50 Systems
Construction Parameters:
Conductor
Stranding
Insulation Material
Insulation Thickness
Number of Conductors
Shield
Jacket Material
Overall Cable Diameter
Approximate Cable Weight
Flame Rating
12 AWG Bare Copper
7x20
Foam FEP
.280” Nom.
1 Center Conductor
95% Bare Copper Braid
Copolymer- Solef
0.352'' Nom.
98 Lbs/1M' Nom.
NFPA 262 Plenum
Electrical & Environmental Properties:
Temperature Rating
Max.Capacitance Between Conductors @ 1 KHz
Velocity of Propagation
Impedance
DC Resistance per Conductor @ 20deg C
Jacket Color
RoHS Compliant
-40deg C to 75deg C
28.5 pf/ft Nom.
66% Nom.
52 ohms Nom.
1.6 Ohms/1M' Nom.
Natural
--
Mhz
1
10
50
100
400
700
900
Mechanical Properties:
Max. Recommended Pull Tension
Min. Bend Radius (Install)
183 lbs.
3.5”
Connectors and Accessories
50 Ohm 3 pc. BNC
CN-25810KBNC
Specification Issue Date: 10/11
This document is the property of West Penn Wire.
. The information contained herein is considered
Proprietary and not to be reproduced by any means
Without written consent of West Penn Wire
Standard Lengths are 1000ft.
The Jacket is sequentially footmarked.
The information presented here is, to the best of our
knowledge, is true and accurate. However, since
conditions of use are beyond our control, all
recommendations or suggestions are presented
without guarantee or responsibility on our part. We
disclaim all liability in connection with the use of
information contained herein or otherwise.
db/100ft
.2
.6
1.3
1.9
4.1
5.9
6.9
ITEM 20
Technical Data Sheet
Plenum Communication Cables
2833 West Chestnut Street
Washington, PA 15301
Toll Free: (800) 245-4964
Fax: (724) 222-6420
www.westpenn-wpw.com
PART NUMBER:
25224B
DESCRIPTION:
18/2 Stranded bare copper conductors, unshielded with an overall jacket.
NEC RATING:
CMP, NEC Article 800
APPROVALS:
(UL) C(UL) Listed or c(ETL)us Listed
APPLICATION:
Indoor within ducts, plenums, and other spaces used for environmental air for (Intercom Systems,
Security Systems, Sound, Audio, Background Music)
Construction Parameters:
Conductor
Stranding
Insulation Material
Insulation Thickness
Number of Conductors
Shield
Drain
Jacket Material
Jacket Thickness
Overall Cable Diameter
Approximate Cable Weight
Flame Rating
18 AWG Bare Copper
7x26
Polymer Alloy
0.010'' Nom.
2
None
None
Flexible Plenum
0.015'' Nom.
0.138'' Nom.
17 Lbs/1M' Nom.
NFPA 262 Flame Test
Electrical & Environmental Properties:
Temperature Rating
Operating Voltage
Max.Capacitance Between Conductors @ 1 KHz
DC Resistance per Conductor @ 20deg C
Insulation Colors
Jacket Color
RoHS Compliant
-10°C To +60°C
300 V RMS
30 pf/ft Nom.
6.2 Ohms/1M' Nom.
Black, Red
Gray, Black, Blue, Green, Yellow
Yes
Mechanical Properties:
Max. Recommended Pull Tension
Min. Bend Radius (Install)
42 lbs
1.4”
Specification Issue Date: 7/06
This document is the property of West Penn Wire.
The information contained herein is considered
. Proprietary and not to be reproduced by any means
Without written consent of West Penn Wire
Cold Environment Precautions: Due to the nature of
PVC Compounds to become non-pliable when stored
or handled in ambient temperatures of 32 deg. F or
less, we recommend the following:
“Prior to installation, condition the cable for at
least 24 hours at room temperature to provide the
best flex properties for ease of installation.”
Standard Lengths are 1000ft.
The Jacket is sequentially footmarked.
The information presented here is, to the best of our
knowledge, is true and accurate. However, since
conditions of use are beyond our control, all
recommendations or suggestions are presented
without guarantee or responsibility on our part. We
disclaim all liability in connection with the use of
information contained herein or otherwise.
ITEM 21
Technical Data Sheet
RG6/U Type CATV Coaxial Cable Plenum
2833 West Chestnut Street
Washington, PA 15301
Toll Free: (800) 245-4964
Fax: (724) 222-6420
www.westpenn-wpw.com
PART NUMBER:
25841
DESCRIPTION:
RG6/U – 1 Conductor 18 AWG Solid, 100% Al. Foil + 77% Al. Braid and an overall Plenum
PVC Jacket.
NEC RATING:
CATVP/ CMP
APPROVALS:
(UL) C(UL) Listed or c(ETL)us Listed
APPLICATION:
Indoor for Plenum:– CATV/MATV
Construction Parameters:
Conductor
Stranding
Insulation Material
Insulation Thickness
Number of Conductors
Shield
Jacket Material
Overall Cable Diameter
Approximate Cable Weight
Flame Rating
18 AWG Bare Copper
Solid
Foam FEP
.170” Nom.
1 Center Conductor
100% Al Foil + 77% Al. Braid
Flexible Plenum PVC
0.235'' Nom.
26 Lbs/1M' Nom.
NFPA 262
Electrical & Environmental Properties:
Temperature Rating
Max.Capacitance Between Conductors @ 1 KHz
Velocity of Propagation
Impedance
DC Resistance per Conductor @ 20deg C
Jacket Color
RoHS Compliant
-20deg C to 60deg C
16.2 pf/ft Nom.
82% Nom.
75 ohms Nom.
6.5 Ohms/1M' Nom.
Ivory
Yes
Mechanical Properties:
Max. Recommended Pull Tension
Min. Bend Radius (Install)
Connectors and Accessories
F Crimp:
F Compression:
91 lbs.
2.4”
Mhz
5
55
100
270
400
550
750
1000
2000
2250
3000
CN-56TFE
CN-FS6PL2
Specification Issue Date: 7/06
This document is the property of West Penn Wire.
. The information contained herein is considered
Proprietary and not to be reproduced by any means
Without written consent of West Penn Wire
Standard Lengths are 1000ft.
The Jacket is sequentially footmarked.
The information presented here is, to the best of our
knowledge, is true and accurate. However, since
conditions of use are beyond our control, all
recommendations or suggestions are presented
without guarantee or responsibility on our part. We
disclaim all liability in connection with the use of
information contained herein or otherwise.
db/100ft
.50
1.6
2.0
2.9
4.5
4.9
6.6
8.0
12.3
13.36
15.42
ITEM 22
Technical Data Sheet
Plenum Miniature Line-Level Audio Cable
2833 West Chestnut Street
Washington, PA 15301
Toll Free: (800) 245-4964
Fax: (724) 222-6420
www.westpenn-wpw.com
PART NUMBER:
D25454
DESCRIPTION:
22/2 Stranded tinned copper conductors, bonded shielded with an overall jacket.
NEC RATING:
CMP, NEC Article 800
APPROVALS:
(UL) Listed
APPLICATION:
Indoor Plenum for: Post Production Facilities, Recording Studio, Sound, Audio.
Construction Parameters:
Conductor
Stranding
Insulation Material
Insulation Thickness
Number of Conductors
Shield
Drain
Jacket Material
Jacket Thickness
Overall Cable Diameter
Approximate Cable Weight
Flame Rating
22 AWG Tinned Copper
7x30
FEP- Teflon
0.007'' Nom.
2 (1 Pair)
100% Aluminum Polyester Foil-bonded
Stranded Tinned Copper
Plenum PVC
0.018'' Nom.
0.130'' Nom.
16 Lbs/1M' Nom.
UL NFPA-262
Color Code Chart
Electrical & Environmental Properties:
Temperature Rating
Operating Voltage
Max.Capacitance Between Conductors @ 1 KHz
Capacitance Between Conductors to Shield @ 1 KHz
DC Resistance per Conductor @ 20deg C
Insulation Colors
Jacket Color
RoHS Compliant
-20deg C to 60deg C
300 V RMS
35 pf/ft Nom.
67 pf/ft Nom.
17 Ohms/1M' Nom.
1. Black, 2. Red
See Chart
--
1.Black
2.Red
3.Gray
4.Blue
5.Brown
Mechanical Properties:
Max. Recommended Pull Tension
Min. Bend Radius (Install)
33 lbs.
1.3”
Specification Issue Date: 7/06
This document is the property of West Penn Wire.
. The information contained herein is considered
Proprietary and not to be reproduced by any means
Without written consent of West Penn Wire
Standard Lengths are 1000ft.
The Jacket is sequentially footmarked.
The information presented here is, to the best of our
knowledge, is true and accurate. However, since
conditions of use are beyond our control, all
recommendations or suggestions are presented
without guarantee or responsibility on our part. We
disclaim all liability in connection with the use of
information contained herein or otherwise.
ITEM 23
AP-5152
AcousticPerformance™ Series
AP-5152
(IGHPOWERINSTALLATION
LOUDSPEAKER
Features
s$-4™$IRECTIVITY-ATCHED
4RANSITIONENSURESSMOOTH
COHERENTPOWERRESPONSE
ACROSSTHELISTENINGPLANE
sDEGREECOVERAGEOFTHE
AXISYMMETRICWAVEGUIDE
MATCHESNATURALCOVERAGE
OFTHEINCHWOOFERATTHE
CROSSOVERPOINTFORCONSISTENT
POWERRESPONSE
sINCHVOICECOILCOMPRESSION
DRIVERFOROUTSTANDINGHIGH
FREQUENCYPERFORMANCE
s-FITTINGSOFFERFLEXIBLE
DEPLOYMENTOPTIONSFORA
VARIETYOFAPPLICATIONS
s#OVEREDBARRIERSTRIPTERMINALS
AND.,3PEAKON™CONNECTOR
s"I!MP0ASSIVESWITCHABLE
sPLY"ALTICBIRCHPLYWOOD
CONSTRUCTION
s'AUGEPOWDERCOATED
STEELGRILLES
s#LEANINDUSTRIALDESIGNWITH
UNADORNEDGRILLESCOMPLIMENT
MOSTDECORSANDSETTINGS
s!VAILABLEINBLACK2!,
ANDWHITE2!,
s#OMPLETE%!3%#!$
")-INFORMATIONAVAILABLE
ATQSCCOM
0ERFORMANCE3PACESq7ORSHIP&ACILITIESq$ANCE.IGHT#LUBSq
3PORTS&ACILITIESq4HEMED%NTERTAINMENT
The QSC AcousticPerformance™ AP-5152
is a professional, two-way, full-range
loudspeaker ideal for a variety of installed
sound reinforcement applications requiring
higher SPL output and a clean appearance.
The AP-5152 uses a high power-capacity,
76mm (3-inch) diaphragm compression
driver and combines it with a 381mm
(15-inch) woofer to deliver exceptional
full bandwidth reproduction.
The uniform power-response of the
AP-5152 loudspeaker is a result of
DMT™ (Directivity Matched Transition), a
design approach that matches LF and HF
coverage in the cross-over region. Another
key to the extraordinary accuracy and flat
power response of the AP-5152 is the
axisymetric waveguide with uncompromised
performance in both the vertical and
horizontal axes. The result is remarkably
consistent coverage and smooth, accurate
reproduction on and off-axis.
The AP-5152 may be used as a passive (fullrange) loudspeaker to minimize amplifier
channel count or it may be bi-amplified for
greater control and performance. To further
enhance performance, bi-amp and fullrange tunings using QSC Intrinsic Correction
techniques are available for Q-Sys and future
QSC products.
The AP-5152 enclosure features M10
mounting points for suspension via eyebolts.
Presenting a clean, unobtrusive look,
AcousticPerformance grilles are unadorned
eliminating the need to cover-up logo
treatments which can be difficult to hide
or remove. The grille is also lined with
acoustically transparent backing adding to
the enclosure’s professional appearance and
the AP-5152 is available in black (RAL 9011)
and white (RAL 9010) finishes.
To minimize impact and disposal fees at the
job site, all AcousticPerformance loudspeakers
are packaged in environmentally friendly,
recyclable cartons.
AP-5152 $ETAILS
PASSIVE MODE
Horizontal
1+
Vertical
Beamwidth
NL4 /
BARRIER
STRIP
360
12+
HF
LPF
LF
N/C
2180
90
HPF
BI-AMP MODE
1+
NL4 /
BARRIER
STRIP
45
12+
HF
2-
LF
10
20
100
1000
Frequency (Hz)
20000
10000
Specifications:
System Details
Frequency Response
Frequency Response (-10dB)
Impedance
SPL/Impedance
100
120
95
110
1
44Hz – 18kHz
Power Capacity
625W / 65V continuous
System Sensitivity2
96dB, 1W@1m
90
100
85
90
Coverage Angle
75˚ Axisymmetric
80
80
Directivity Factor (Q)
8.3
75
70
Directivity Index (DI)
9.2
70
60
65
50
60
40
55
30
50
20
45
10
40
20
Responses shown with
recommended processing
100
1000
Frequency (Hz)
10000
Recommended Crossover
950 Hz, 48dB/octave
Maximum Rated SPL
Passive: 123dB @1m, continuous3
129dB @1m, peak4
Rated Impedance
8Ω
HF Transducer
76mm (3-inch) voice coil, compression
LF Transducer
381mm (15-inch) driver with 102mm
(4-inch) VC; 625W / 65V (2 Hrs)
Optional Accessories
M10 Kit-W
driver; 72W / 24V (2 Hrs)
0
20000
Enclosure Details
Input Connector
Covered Barrier Strip, NL4 connector
Enclosure Material
15-ply Baltic birch plywood
Attachment Points
15x M10 threaded inserts
Color
Black (RAL 9011), White (RAL 9010)
Grille
16 Gauge powder coated steel
Dimensions (HxWxD)
813mm x 445mm x 386mm
(32" x17.5" x 15.2")
Net Weight
36.2 kg (80 lb)
Shipping Carton Dimensions
(HxWxD)
857mm x 560mm x 503mm
(33.8x22x20-inches)
Shipping Weight
40.8kg (90 lbs)
As part of QSC’s ongoing commitment to product development,
specifications are subject to change without notice.
1
2 hour rating using IEC60268 noise based on minimum impedance
Mid-band based on nominal impedance
3
Calculated as the nominal sensitivity plus 10x the log of continuous
rated power in volts squared divided by nominal impedance
4
Calculated as the continuous calculated max output plus 6dB
2
AP-5152 (ORIZONTAL0OLARS
Polar Plot
200Hz
Polar Plot
90
500Hz
250Hz
630Hz
315Hz
800Hz
400Hz
1000Hz
180
-6
0
+6
0
180
270
0
+6
-6
0
+6
0
Polar Plot
90
3150Hz
1600Hz
4000Hz
2000Hz
5000Hz
2500Hz
6300Hz
180
-6
0
+6
0
270
90
10000Hz
12500Hz
16000Hz
180
-6
270
90
180
270
Polar Plot
8000Hz
-6
270
Polar Plot
1250Hz
90
0
+6
0
0
AP-5152 6ERTICAL0OLARS
Polar Plot
200Hz
Polar Plot
90
500Hz
250Hz
630Hz
315Hz
800Hz
400Hz
1000Hz
180
-6
0
+6
0
180
270
0
+6
-6
0
+6
0
Polar Plot
90
3150Hz
1600Hz
4000Hz
2000Hz
5000Hz
2500Hz
6300Hz
180
-6
0
+6
0
270
90
10000Hz
12500Hz
16000Hz
180
-6
270
90
180
270
Polar Plot
8000Hz
-6
270
Polar Plot
1250Hz
90
0
+6
0
0
AP-5152 4ECHNICAL$RAWINGS
-AC!RTHUR"OULEVARDs#OSTA-ESA#!s0HORs&AX
© 2012 QSC Audio Products, LLC. All rights reserved. QSC and the QSC logo are registered
trademarks of QSC Audio Products, LLC in the U.S. Patent and Trademark office and other
countries. DMT is a trademark of QSC. Speakon is a registered trademark of Neutrik
AP-5152 Spec Sheet 12/12/2012
PLEASERECYCLE
ITEM 24
AD-S52
AcousticDesign™ Loudspeaker
Features
s 5
.25", 2-way design—in a lightweight, contemporary styled
multipurpose enclosure
sMagnetically shielded LF transducer—ideal for use near
video monitors
sFlexible ball mount assembly included—for convenient installation
s70/100 volt transformer versions available—for use with
distributed audio systems
sOptional yoke mount bracket available
The QSC AcousticDesign AD-S52 is a full range,
Specifications
AD-S52
AD-S52T
surface mount loudspeaker with sleek, contemporary
Configuration
Compact 2-way, ported enclosure
Compact 2-way, ported enclosure
styling that fits perfectly into multiple environments
Transducers
Low-frequency Transducers
5.25" shielded
5.25" shielded
High-frequency Transducer
1" neodymium tweeter
1" neodymium tweeter
75 Hz – 19 kHz
75 Hz – 19 kHz
Useable Frequency Range (-10 dB) 60 Hz – 20 kHz
60 Hz – 20 kHz
and
applications
including
hotels,
restaurants,
convention facilities, and multimedia environments.
The loudspeaker’s low-frequency driver is magnetically
shielded, making the AD-S52 perfect for use near
video monitors. Available in black or white, these great
sounding, weather resistant enclosures can be painted
to match any specific decor.
The AD-S52 is a high output, 2-way design
Frequency Range1
Frequency Response (-6 dB)
Maximum
Output2
Calculated Peak Output
110 dB SPL
107 dB SPL
Calculated Continuous Output
104 dB SPL
101 dB SPL
8Ω
8Ω switchable
incorporating a 5.25" weatherproof, LF transducer and
Nominal Impedance
a 1" neodymium tweeter. This exceptional loudspeaker
Power Rating
carries the added benefit of built-in dynamic power
RMS Power Handling3
60 W (100 hours IEC)
60 W (100 hours IEC)
protection—thus ensuring system reliability in the
Recommended Max Amp Power
120 W RMS
120 W RMS
Sensitivity
86.5 dB, 2.83V, 1 m, free field (4π)
86 dB, 2.83V, 1 m, free field (4π)
Nominal Coverage (HV)
90° x 90°
90° x 90°
event of overload conditions.
The AD-S52T models are equipped with a 70/100 volt
Transformers
matching transformer for distributed audio systems.
Type
−
Custom low distortion laminated core,
wide bandwidth design
Taps
−
70V: 30, 15, 7.5, 3.75 W
100V: 30, 15, 7.5 W
There is a transformer tap switch on the rear panel
for setting the power level of the loudspeaker. This
switch may also be set for 8 ohm operation, bypassing
the transformer completely—providing greater system
Enclosure
Material
Injection molded, weather resistant, high impact polystyrene
Finish
White or black (paintable)
The AD-S52 system package includes a ball mount
Weather Resistant
Yes
assembly for convenient installation of the enclosure
Grille
Heavy duty powder coated aluminum
in a wide variety of orientations. If desired, the ball
Connectors
Pair of 5-way binding posts
mount adapter’s back plate can be removed, reducing
Mounting Hardware
Included ball mount assembly; optional yoke mount bracket available
the overall depth of the assembly and the footprint of
Weight - Net / Shipping
15 lb (6.8 kg) / 22 lb (10 kg)
flexibility compared to most competing products.
18 lb. (8.2 kg) / 25 lb (11.4 kg)
the mount on the wall. Further, the assembly includes
a weather resistant input connection cover to protect
the 5-way binding post input terminals.
1) All frequency ranges specified refer to measured free field response (full space, 4π)
2) Calculated SPL at 1m, (full space, 4π), speaker operating at rated RMS power with 6 dB crest factor pink noise input, 50 Hz – 20 kHz
3) Maximum input power tested in accordance with IEC 268-5 recommendations, 80 Hz – 20 kHz band limiting, 6 dB signal crest factor
AD-S52
Dimensions | Frequency Response and Impedance
7.02"
178.3 mm
9.33"
211.6 mm
4"
101.6 mm
11.28"
286.5 mm
11.81"
299.8 mm
Top
D"30,
Frequency Response
and Impedance*
Side
110
36
105
33
100
30
95
27
90
24
85
21
80
18
75
15
70
12
65
9
60
6
55
3
50
20Hz
50
100
200
500
1K
2K
5K
10k
0
20K
1K
2K
5K
10k
20K
Ohm
Front
Frequency (Hz)
110
105
Horizontal Off-Axis
Frequency Response**
(0°, 15°, 30°, 45°)
100
95
90
D"30,
85
80
75
*Graph shows free field SPL at 1 W, 1 m
**1/3rd octave smoothing applied to off-axis
curves for clarity
70
65
60
55
50
20Hz
50
100
200
500
Frequency (Hz)
Specifications subject to change without notice.
QSC and the QSC logo are registered trademarks of QSC Audio Products, LLC in the U.S. Patent and Trademark office and other countries.
AcousticDesign is a trademark of QSC Audio Products, LLC. All other trademarks are the property of their respective owners. Patents may apply or be pending.
-AC!RTHUR"OULEVARDs#OSTA-ESA#!s0HORs&AX
AD-S52 Spec Sheet - 06/18/08
qscaudio.com
ITEM 25
AD-C42T
AcousticDesign™ Ceiling Mount Speaker
Features
s" polypropylene cone woofer
s" titanium dome tweeter
s7ATTCONTINUOUSPOWERHANDLING7ATTPEAK
s6MULTITAPTRANSFORMERWITHOHMBYPASS
s#RINGANDTILERAILSINCLUDED
The AcousticDesign Series of installation loudspeaker
products from QSC Audio expands with the new
AD-C42T ceiling mount loudspeaker system. Designed
for background and general purpose audio playback,
the new AD-C42T is compact and acoustically matched
to the entire AD Series. Rated for 40 Watts continuous
power handling and able to take up to 160 Watt
peaks, the compact AD-C42T is suitable for a wide
variety of ceiling installations
The 4" woofer is equipped with a polypropylene
cone for protection in humid environments. The
driver features a synthetic rubber surround and in its
sealed enclosure is optimized to deliver useable low
frequency extension below 70 Hz. The high frequency
device is a co-axial, post mounted 0.75" dome tweeter
with a titanium diaphragm and a cloth surround. The
coaxial post is mounted slightly off center in relation
to the low frequency driver in order to lessen the
destructive interference often found with axisymmetric
post mounted coaxial systems. The conical dispersion
of the AD-C42T is 100° and sensitivity measures
88 dB SPL.
The baffle and mounting tabs are molded from highimpact polystyrene. The rear enclosure is a heavy
gauge, powder coated steel. The attractive aluminum
grille is backed with an acoustically transparent white
cloth. On the rear of the enclosure is an input cup
that features a conduit attachment point plus an
additional knockout for daisy-chain wiring. Input signal
connection is made with a high temperature resistant
ceramic screw terminal for compliance with European
safety standards.
The AD-C42T is factory shipped with C-rings and tile
rails for installation. New construction rings (ADC-NC4)
and mud rings (ADC-MR4) are also available separately.
The AD-C42T is equipped with a 70/100 V transformer
with multiple taps and an 8 ohm bypass.
Specifications
Configuration
Compact 2-way, sealed enclosure
Transducers
er
Low-frequency
4" (10 cm) weather resistant, polypropylene cone woofer
High-frequency
0.75" titanium dome tweeter
Frequency Range1
er
Frequency Response (-6 dB)
72 Hz - 20 kHz
Useable Frequency Range (-10 dB)
60 Hz - 20 kHz
Maximum
Output2
er
Calculated Peak Output
110 dB SPL
Calculated Continuous Output
104 dB SPL
Nominal Impedance
8Ω
Power Rating
er
RMS Power Handling3
40 W (100 hours IEC)
Recommended Max Amp Power
80 W RMS
Sensitivity
Transformers
88 dB, 2.83 V, 1 m, free space (4π)
er
Type
Custom low distortion laminated core, wide bandwidth design
Taps
70 V: 30, 15, 7.5, 3.8 W / 100 V: 30, 15, 7.5 W / 8 Ω selected by switch
Environmental
Exceeds Mil Spec 810 for humidity, salt spray and dust;
IEC 60529 IP-X3 splash rating
Agency Rating
Listed UL1480, UL2043 safe for use in air handling spaces;
Transformer is Listed UL1876; Compliant BS/EN 60849 safety standards
Enclosure
er
Material
Injection molded, high impact polystyrene baffle on a steel enclosure
Finish
White (paintable)
Grille
Painted aluminum
Connectors
Ceramic block or 4-pin Euro terminals in fire protective sub-chamber
Mounting Hardware
Rails and C-ring for ceiling tile installation
Weight - Net / Shipping (pair)
Available Accessories
6.1 lb (2.7 kg) / 18 lb (8.2 kg)
ADC-MR4 / ADC-NC4
1) All frequency ranges specified refer to measured free field response.
2) Calculated SPL at 1m, (free space, 4π), speaker operating at rated RMS power with pink noise within specified frequency range
3) Maximum input power tested in accordance with IEC 268-5 recommendations, 50 Hz - 20 kHz band limiting, 6 dB signal crest factor.
AD-C42T
Dimensions | Frequency Response
6.7"
171 mm
7.5"
191 mm
6.5"
165 mm
8.9"
226 mm
.4"
9 mm
Side
Side
Front
110
100
dBSPL
90
80
70
60
20
50
100
200
500
1K
2K
Hz
5K
10k
20K
&REQUENCY
Specifications subject to change without notice.
QSC and the QSC logo are registered trademarks of QSC Audio Products Inc. in the U.S. Patent and Trademark office and other countries.
AcousticDesign is a trademark of QSC Audio Products, Inc. All other trademarks are the property of their respective owners.
-AC!RTHUR"OULEVARDs#OSTA-ESA#!s0HORs&AX
AD-C42T Spec Sheet - 10/11/07
qscaudio.com
ITEM 26
I-82H
)3)33ERIES,OUDSPEAKER
Features
s"WAYSYSTEMnin a lightweight, weather-resistant,
multipurpose enclosure featuring a heavy duty, powder
coated aluminum grille
s!DVANCED$IRECTIVITY»ROTATABLEWAVEGUIDEn(90° x 60°)
enables the loudspeaker to deliver accurately focused sound,
regardless of the enclosure’s mounted orientation
s(IGHPOWERCAPABILITYWITHDYNAMICPROTECTIONnrated at
240 watts (IEC) with power protection circuitry to prevent overloads
s#ONTEMPORARYSTYLEWEATHERRESISTANTENCLOSUREAND COMPONENTSnideal for a wide range of applications
s4WOPARALLEL3PEAKON®CONNECTORSnfor quick, secure audio
input setup
s0OLECUPANDMICSTANDADAPTERSnincluded for versatile
mounting options
The I-82H is an 8", 2-way, full-range loudspeaker
Specifications
with contemporary styling that integrates into
Configuration
multiple environments. With the ability to be pole
Transducers
and mic stand mounted, truss mounted, or used
as a floor monitor/stage fill, these injection molded
speakers are an excellent choice for musicians,
Compact 2-way, ported enclosure
Low Frequency Transducer
8" high-power treated paper cone, 2" voice coil, neodymium magnet
High Frequency Transducer
1" exit high-output compression driver
Frequency Range1
mobile entertainers, and others needing a high-
Frequency Response
80 Hz – 21 kHz (-6 dB)
quality, lightweight SR package that sounds great, is
Usable Frequency Range
60 Hz – 22 kHz (-10 dB)
visually unobtrusive, and with its built-in handles, is
easy to transport.
Maximum
Output2
Calculated Peak Output
120 dB SPL
Calculated Continuous Output
114 dB SPL
The I-82H enclosure incorporates an 8" weatherproof,
Impedance
LF transducer with a heavy-duty double roll cloth
Power Rating
8Ω nominal (7Ω minimum, 210 Hz, 135Ω maximum)
surround and a 1" exit HF compression driver.
RMS Power Handling3
240 W (IEC, 8 hours)
The HF driver is coupled with QSC’s unique
Recommended Max Amp Power
400 W RMS
Advanced Directivity rotatable waveguide—enabling
the loudspeaker to deliver accurately focused
sound, regardless of its orientation. For quick and
secure input setup, the I-82H provides two parallel
Speakon connectors.
An ideal solution for a variety of mobile SR
applications, the I-82H includes a pole cup bracket
for pole mount applications as well as a 5/8"27 mic stand adapter that fits most mic and
boom stand hardware. With the addition of QSC’s,
optional I-YM8 Yoke Mount/Floor Monitor Kit (which
contains a bracket with swivel extension feet), the
I-82H can be horizontally pole mounted for pan
and tilt focusing or used as a floor monitor. For truss
mounting, the I-YM8 accepts most industry standard
truss clamps.
Power Limiting
Dynamic, full range power protection circuitry activated by signal
overload conditions
Sensitivity
90.5 dB, 1 m, free field
Nominal Coverage
90°H x 60°V (-6 dB) / rotatable to 60°H x 90°V
Bass Loading
Ported, tuned to 65 Hz
Enclosure
Material
Injection molded, weather resistant, high impact polystyrene
Finish
Black
Weather Resistance
Yes
Grille
Heavy duty powder coated aluminum
Connectors
Two Neutrik Speakon NL4FC connectors wired in parallel,
Mounting Hardware
Included: Pole cup and mic stand adapter. Optional: I-YM8 Yoke mount
Weight – Net / Shipping
17.5 lb (7.9 kg) / 20.5 lb (9.3 kg)
1) All frequency ranges specified refer to measured free field response (full space, 4π)
2) Calculated SPL at 1 m, full space (4π), speaker operating at rated RMS power with pink noise within specified
frequency range
3) Maximum input power tested in accordance with IEC 268-5 recommendations, 50 Hz – 20 kHz band limiting,
6 dB signal crest factor, 8 hours
I-82H
Dimensions | Frequency Response and Impedance
4OP
/PTIONAL)9-9OKE-OUNT
10"
257 mm
Weight – Net: 2.8 lb (1.27 kg)
Shipping: 5.0 lb (2.26 kg)
M10 x 1
~8 mm deep
7.4"
188 mm
5.9"
150 mm
11.2"
284 mm
6.2"
157 mm
17.1"
434.3 mm
17.4"
442 mm
0.24"
6 mm
diameter shank
2.75"
69.9 mm
~9°
3IDE
"ACK
1.375"
34.9 mm
&RONT
= 0.226"
(5.6 mm)12x
15.875"
403.2 mm
dBSPL
&REQUENCY
2ESPONSE
ƒƒƒƒ
*Graph shows free field SPL
at 1 W, 1 m
**1/3rd octave smoothing
applied to off-axis curves
for clarity
110
105
100
95
90
85
80
75
70
65
60
55
50
20 Hz
110
105
100
95
90
85
80
75
70
65
60
55
50
20 Hz
144
132
120
108
96
84
72
60
48
36
24
12
0
50
100
200
500
1K
2K
Frequency (Hz)
5K
10K
12"
304.8 mm
= 0.256"
(6.5 mm)4x
4.25"
108 mm
Ohm
dBSPL
&REQUENCY
2ESPONSEAND
)MPEDANCE
2"
50.8 mm
= 0.5"
(12.7 mm)1x
5.1"
129 mm
20K
12.5"
317 mm
50
100
200
500
1K
2K
5K
10K
20K
Frequency (Hz)
Specifications subject to change without notice.
QSC and the QSC logo are registered trademarks of QSC Audio Products, LLC in the U.S. Patent and Trademark office and other countries. Advanced Directivity is a trademark
of QSC Audio Products, LLC. Speakon is a trademark of Neutrik. All other trademarks are the property of their respective owners. Patents may apply or be pending.
-AC!RTHUR"OULEVARDs#OSTA-ESA#!s0HORs&AX
I-82H Spec Sheet 06/19/08
qscaudio.com
®
ProSafe Plus 16-port Fast Ethernet Switch
FS116E
Data Sheet
FAST
10 0
Mbps
ITEM 27
More Capabilities beyond Plug-and-play connectivity
Today’s growing businesses are both placing more demands on and relying more on their network.
Companies are putting more applications and demands on their Ethernet Infrastructure. Using VoIP
phones and IP cameras require more than simple plug-and-play connectivity. Additionally, Internetbased applications such as Hotmail and Google Calendaring have made keeping the network up
a business-critical need. However, companies do not necessarily have more money or advanced
training to deal with complex managed switches. NETGEAR’s new ProSafe Plus Switches meet this
growing need by providing easy to use visibility and limited configuration capabilities. To provide
more insight into the network behavior, ProSafe Plus Switches offer traffic monitoring for users to
observe traffic behavior. Additionally, if there are connectivity issues, these switches offer a cable
diagnostic test capability that can identify and even locate problems in the cables.To optimize traffic
through the switches, ProSafe Plus Switches offer both port and tag-based prioritization to keep
latency-sensitive traffic moving ahead of less critical packets. Also, as a means of improving security
or managing collision domains, ProSafe Smart Switches offer VLAN technology. ProSafe Plus Switches
offering these monitoring and configuration capabilities at a slight cost premium over un anaged
switches, delivering great value to the end user.
Additionally, furthering NETGEAR’s support of the environment, ProSafe Plus Switches have powersaving Green Ethernet technology. The FS116E is the first 16-port Fast Ethernet on the market
with such Green Ethernet features. The switch comes in a sturdy metal case with a fan-less design
for silent operation.
Features
VË2ÄjË?ÄË?Ë+Ö~ˆ?™aˆ+?ßËÄ݉ÍW†ËÁËÖÄjË͆jËW™x~ÖÁ?͉™ËÖ͉‰ÍßËwÁËĉ”¬jËÄjÍÖ¬
VˤÉˬÁÍÄËaj‰ÜjÁËÖ¬Ë͝ËÔååË M¬ÄËM‰ˆa‰ÁjW͉™?ËM?™a݉a͆˝™Ëj?W†Ë¬ÁÍ
VË,Ö?‰Íß˝wË.jÁ܉WjË®,.¯ËwÁˬÁ‰Á‰Í‰ã‰™~˙jÍݝÁËÍÁ?wxW
VË7‰ÁÍÖ?Ë!Ë®7!¯ËÄÖ¬¬ÁÍËwÁ˙jÍݝÁËÄj~”j™Í?͉™Ë?™aËÄjWÖÁ‰Íß
VË0ÁÖMjƝÍËW™™jW͉™Ë¬ÁMj”Ë܉?ËW?MjËÍjÄÍ
VË?™a݉a͆˔?™?~j”j™ÍË͝Ë?ܝ‰a˙jÍݝÁËW™~jÄ͉™Ä
VË!jÍݝÁËÍÁ?wxW˔™‰ÍÁ‰™~
VË+ÁÍ˔‰ÁÁÁ‰™~
VËÁ?aW?ÄÍËÄ͝Á”ËW™ÍÁ
NETGEAR Green
VË2¬Ë͝ËÉå°ËÝjÁˬÝjÁËW™Ä֔¬Í‰™Ë͆?™Ë͆jˬÁj܉ÖÄ˔aj1
VËÖ͝ˬÝjÁˆaÝ™Ë”ajËW™ÄjÁÜjÄËj™jÁ~ßË݆j™Ë?ˬÁÍˉÄ˙ÍËW™™jWÍja
VËjÄÄËÍÁ?™Ä”‰ÍˬÝjÁË݆j™Ë͆jËW?MjˉÄËƝÁÍˮ֙ajÁˤå˔¯
VË+?W?~‰™~˔?™Öw?WÍÖÁjaË݉͆Ë?Íːj?ÄÍËoå°ËÁjWßWja˔?ÍjÁ‰?
The NETGEAR Difference
ProSafe Plus 16-port
Fast Ethernet Switch
(FS116E)
FS116E
Power Saving on Fast Ethernet Switch
Quick
Configuration
Prioritize video/voice
Monitor Network Traffic
Internet
Create network groups
Connects to
broadband modem
Troubleshoot connection problems
24 / 7
TECHNICAL
S U P P O R T*
1-888-NETGEAR (638-4327)
Email: info@NETGEAR.com
Key
VLAN 1
VLAN 2
ProSafe 8-port
Gigabit VPN Firewall
(FVS318G)
Connects to laptops
with internal Wireless-N
or Wireless-N adapters
ProSafe Wireless-N
Access Point
(WNAP210)
IP camera
Connects to servers
with Fast Ethernet
PCI Adapters
(FA311)
Connects to PCs
with Fast Ethernet
PCI Adapters
(FA311)
ReadyNAS NVX
(RNDX4250)
ProSafe ® Plus 16-port Fast Ethernet Switch
Features
FS116E
FS116
JFS524
FS116E
JFS524E
16
24
16
24
V
V
V
V
10/100 Mbps ports
Auto Uplink™
Divide network into groups (VLAN)
V
V
Set traffic priority (QoS)
V
V
Bandwidth control
V
V
Cable Test
V
V
Green Ethernet
V
V
Lifetime
Lifetime
Rack-mountable
V
Warranty
Lifetime
Technical Specifications
VËSystem Requirements
– Ethernet Category 5 cable
– Network card for each PC
– Microsoft® Windows® XP or Vista for
running Configuration Utility
VËStandards Compliance:
– ËoåԱωˤå.ˆ0Ë͆jÁ™jÍË
– ËoåÔ±ÏÖˤåå.ˆ09Ë?ÄÍË
Ethernet
– ËoåÔ±ÏÞËw֐ˆaÖ¬jÞËzÝËW™ÍÁ
– ™ÁÄËËoåÔ±¤¬Ë¬Á‰Á‰ÍßËÍ?~ÄË
– ™ÁÄËËoåÔ±¤,Ë7!ËÍ?~Ä
– Compatible with all major
network software
VËNetwork Ports
– .‰ÞÍjj™Ë®¤É¯Ë¤åʤååË M¬ÄË
Ethernet RJ-45 ports
VËAC Power
– ¤Ô7^ˤ±åˬÝjÁË?a?¬ÍjÁ^ːW?‰ãjaË
to country of sale
– Power consumption: 5.46W
Lifetime
VËPerformance
– MAC address: 4 K
– ?™a݉a͆]ËϱÔˬMÄ
VËPhysical Specifications
– ‰”j™Ä‰™ÄË®†ËÞËÝËÞËa¯]Ë
ÔÈËÞËÔoÈËÞˤåÏ˔”Ë
(1.1 x 11.3 x 4.1 in)
– 8j‰~†Í]Ëå±o¤Ë~Ë®¤±ÈšËM¯
VËSwitch Environmental
Specifications
– Operating temperature:
ÏÔdË͝ˤÔÔdËË®ådË͝ËyåËd
¯
– #¬jÁ?͉™~ˆ֔‰a‰Íß]˚å°Ë”?މ”Ö”Ë
relative humidity, non-condensing
– WÖÄ͉W˙‰ÄjːjÜj]Ëå
– 0]Ë|^å|É^oo初ÖÁÄ
VËElectromagnetic Compliance
– CE mark (commercial)
– FCC Part 15 Class A
– !ËyyåÔÔË®
.+-ËÔÔ¯Ë
?ÄÄË
– VCCI Class A
– C-Tick
VËSafety Agency Approvals
– Ê7Ë!ËÉåšyå
– VËStatus LEDs
– Power
– Link, speed, and activity indicators
built into each RJ-45 port
V
Warranty
ProSupport Service
Packs Available
VËOnCall 24x7, Category 1
– + åÏϤˆ¤ååË®2.¯
– + åÏϤˮ™™ˆ2.¯
VËXPressHW, Category 1
– +--åÏϤ
Package Contents
– ProSafe® Plus 16-port Fast Ethernet
Switch (FS116E)
– Wall-mount kit
– AC Power Adapter
– ,։WË™ÄÍ?Ë։aj
– ™ÄÍ??͉™Ë
Ë݉͆Ë
Configuration Utility software
Related Products
– ProSafe Plus 5-port Gigabit Ethernet
.݉ÍW†Ë®.¤åy¯
– ProSafe Plus 24-port Fast Ethernet
Switch (JFS524E)
Ordering Information
–
–
–
–
!Á͆˔jÁ‰W?]Ë.¤¤Éˆ¤åå!.
+?W‰xWË?™aËÖÁ¬j]Ë.¤¤Éˆ¤åå+.
2]Ë.¤¤Éˆ¤åå2.
ÖÄÍÁ?‰?]Ë.¤¤Éˆ¤åå2.
– NETGEAR Lifetime Warranty
ÏyåËË+Ö”jÁ‰?ËÁ
San Jose, CA 95134 USA
1-888-NETGEAR (638-4327)
E-mail: info@NETGEAR.com
www.NETGEAR.com
© 2009 NETGEAR, Inc. NETGEAR, the NETGEAR Logo, NETGEAR Digital Entertainer Logo, Connect with Innovation, FrontView, IntelliFi,
PowerShift, ProSafe, ProSecure, RAIDar, RAIDiator, RangeMax, ReadyNAS, Smart Wizard, X-RAID, and X-RAID2, are trademarks and/or registered
trademarks of NETGEAR, Inc. and/or subsidiaries in the United States and/or other countries. Mac and the Mac logo are trademarks of Apple
Inc., registered in the U.S. and other countries. Other brand names mentioned herein are for identification purposes only and may be trademarks
of their respective holder(s). Information is subject to change without notice. All rights reserved.
This product comes with a limited warranty, the acceptance of which is a condition of sale. This product has been tested for quality assurance
and this product or its components may have been recycled.
*Basic technical support provided for 90 days from date of purchase.
1
Maximum power savings when compared to the equivalent NETGEAR Unmanaged product.
D-FS116E-3
Clear-Com Encore
TM
PS-702 Two-Channel Intercom Power Supply
ITEM 28
PS-702 Front view
The PS-702 can supply up to 2 amps at 30 volts DC to two channels in a
1-RU. This is sufficient to power up to 40 beltpacks,10 speaker stations, or
12 headset stations even under the most demanding conditions. Either
channel is capable of supplying up to 1.2 amps. The full current capacity
may be divided between the two channels.
Clear-Com’s advanced fail-safe design can sense the difference between
a short and an overload. Should a problem occur, each channel’s DC
overload/fault LED identifies the power supply’s response to the problem:
solid means an overload is sensed, but still powered; blinking means
power has been temporarily cut off to protect the power supply. If both
channels are operating and one channel has a fault, the other channel
will continue to operate normally. Power is restored to the shorted or
overloaded channel in a little as .5 seconds. With our exclusive Intelligent
Fault/Overload Sensing (IFOS), the PS-702 will dynamically increase this
time period before attempting another reset until the fault or overload
is corrected. This function significantly extends component life. And
there is no need to disconnect stations for the power supply to reset.
The unit also offers a convenient front panel intercom line jack, switchable
to either channel. This can be quite handy for trouble-shooting or simply a
time saver when quick access to either intercom line is needed. A 440Hz
tone is available on either or both channels and is indispensable for
system diagnostics and set-up. Simply flip a switch, set a level, and go.
Like all current Clear-Com Party-Line power supplies, two or more units
can be connected in parallel for increased system capacity or backup
redundancy. Multiple units will automatically synchronize their response
to power faults and overloads. The PS-702 can also operate as a singlechannel unit by using the front-panel A+B link switch.
Features:
tProvides up to 2 amps in only 1RU
t4VQQPSUTVQUPCFMUQBDLT
speaker stations or 12 headset
stations
t&YDMVTJWF*FOS Intelligent Fault/
Overload Sensing for system reset
tFront panel intercom line jack
selectable for either channel
t"#-JOLTXJUDIGPSTJOHMFDIBOOFM
operation
t#BMBODFEQSPHSBNJOQVUXJUIHMPCBM
and individual channel controls
t6OJWFSTBMQPXFSTVQQMZBDDFQUT
100-240 VAC
t0WFSMPBEGBVMUJOEJDBUPSGPSFBDI
channel
t#VJMUJOUFTUUPOFHFOFSBUPSGPSTFU
up and diagnostics
t4XJUDIBCMFUFSNJOBUJPOTGPSFBDI
channel
tWorks in parallel with other power
supplies and main stations
t6--JTUFEBOE$&DFSUJöFE
www.clearcom.com
Clear-Com Encore
TM
PS-702 Two-Channel Intercom Power Supply
TERM
A
OFF
PS-702
TERM
B
OFF
ON
CHANNEL A
LEVEL
ADJUST
ON
PROGRAM INPUT
CHANNEL B
PS-702 Back Panel
Technical Specifications:
dBu is an absolute measurement. 0 dBu is
referenced to 0.775 volts RMS
Program Line Input
Maximum Level before Clipping: >= 20dBu
Input Impedance:
>= 5KΩ
Frequency Response
Program Input - Party Line:
200 - 20KHz ± 3dB
Max Distortion
Program Input - Party Line:
<= 0.2%
Noise
Program Mic Input - Party Line:< -70dBu
Short Circuit Recovery Time
(1st short):
<= 0.5 sec
Short Circuit Recovery Time: >= 20 shorts in
20sec) <= 20 sec
>= -16dB
Rear Panel Controls
(2) Termination On-Off switches
(1) Volume control
Min Gain
Program Input - Party Line:
<= -20dB
Front Panel Connectors
Intercom (1) XLR-3M
100 - 240 VAC
50 - 60 Hz
<= 60 VAC
30 VDC ± 0.5V
1.2 A
2 A (Do not exceed
the 1.2A rating for
more than 2 seconds
per 1 minute period)
Dimensions
19 in. W x 1.75 in. H x 7.5 in. D
(483 mm x 44 mm x 190 mm)
Station Capacity
Up to 40 RS-601 beltpacks or 10 speaker stations or
12 headset stations distributed over both channels Weight
6.16 lbs. (2.80 kg)
Rear Panel Connectors
Intercom:
(6) XLR-3M (3 per
channel)
Program:
(1) XLR-3F
AC Power:
IEC 320 connector
Max Gain
Program Input - Party Line:
Mains Power
Input Voltage Range:
Input Frequency Range:
Input Power:
Output Voltage:
Output Current per Channel
(Continuous):
Output Current per Channel
(Peak):
Environmental
32˚ - 122˚F (0˚ - 50˚C)
Front Panel Controls & Indicators
(1) Intercom channel switch
(1) A+B link switch
(2) Program switch
(2) Send level controls
(1) Test tone switch
(2) Overload LEDs
(1) Link indicator LED
(1) Power indicator LED
(1) Power switch
Notice About Specifications
While Clear-Com makes every attempt to maintain the
accuracy of the information contained in its product
manuals, that information is subject to change without
notice. Performance specifications included in this manual
are design-center specifications and are included for
customer guidance and to facilitate system installation.
Actual operating performance may vary.
www.clearcom.com
Americas and Asia-Pacific Headquarters California, United States Tel: +1.510.337.6600
Europe, Middle East and Africa Headquarters Cambridge, United Kingdom Tel: +44 1223 815000
China Office Beijing, P.R. China Tel: +86-10-65811360/65815577
© 2011. Clear-Com LLC. All rights reserved. ® Clear-Com, the Clear-Com logo, and Clear-Com Encore are registered trademarks of HM Electronics.
ITEM 29
YamahaMY16-CII
16 Channel CobraNet™ network I/O card
MY16-CII
16 Channel I/O CobraNet™ interface that integrates into any standard CobraNet™ network. Primary and secondary
network connections (2 RJ45 connectors), and reduced power consumption for compatibility with additional models.
Networked Signal Processors
ITEM 30
bssaudio.com
Soundweb London
BLU-800
™
TM
Soundweb
BLU-800
CAUTION: TO REDUCE THE RISK
AVIS:
OF FIRE REPLACE ONLY WITH THE
SAME TYPE AND RATING OF FUSE
T1.6AH - 250V FUSE
UTILISER UN FUSIBLE DE
RECHANGE DE MEME TYPE
100-240V ~ 50/60Hz, 55W
THIS EQUIPMENT MUST BE EARTHED
MANUFACTURED IN THE USA BY BSS AUDIO
PRIMARY
SECONDARY
4
IN
BLU link
CobraNet
IN
OUT
3
2
1
S
S
S
S
S
S
S
S
RS232
ETHERNET
3
2
1
S
S
S
S
S
S
S
S
D
OUT
LOCATE
4
B
BUDDYLINK / 48K
A
C
OVERVIEW:
The Soundweb London BLU-800 offers configurable I/O, configurable signal processing, CobraNet audio and a high
bandwidth, fault tolerant digital audio bus.
The BLU-800 has open architecture which is fully configurable through HiQnet™ London Architect. A rich palette
of processing and logic objects and a “drag and drop” method of configuration provide a simple and familiar design
environment.
This processor features CobraNet audio with primary and secondary ports for fault tolerance. Control is through a separate
Ethernet port which allows CobraNet and control networks to be easily separated or mixed depending upon requirements.
The BLU-800 also features a low latency, fault tolerant digital audio bus of 256 channels which uses standard Category
5e cabling giving a distance of 100m between compatible devices. Fiber media converters can be used to increase the
distance between devices to over 40km.
Four card slots which accommodate analog inputs, analog outputs, digital inputs and digital outputs in banks of four
facilitate many different device I/O configurations.
Analog Input Cards provide software configurable gain in 6dB steps up to +48dB per channel and software selectable
Phantom Power per channel. Digital Input Cards and Digital Output Cards process AES/EBU and/or S/PDIF audio and offer
a variety of clocking and syncing options. (Further information about the I/O cards can be found on dedicated datasheets)
Phantom Power, Sync, Signal Present and Clip information per channel is easily accessible, without the requirement for
a PC, from clear front panel LED indication. Device-specific information such as Device Name, Device Type, Firmware
Version Number, Time, IP Address and Subnet Mask is available from the front panel display. A bi-directional locate
function allows devices to be identified both from and within HiQnet London Architect.
12 Control Inputs and 6 Logic Outputs allow the BLU-800 to be integrated with GPIO compatible devices. The
Soundweb London Interface Kit, comprehensive documentation which details how Soundweb London systems can be
integrated with third party control systems, is included within the installation of HiQnet London Architect.
The BLU-800 and the other members of the Soundweb London family provide the building blocks of the perfectly tailored
system solution.
K E Y F E AT U R E S :
Four Input / Output Card Slots
Configurable Inputs / Outputs
Analog Inputs (with Phantom Power per
Channel)
Analog Outputs
Digital Inputs (AES/EBU and S/PDIF)
Digital Outputs (AES/EBU and S/PDIF)
Configurable Signal Processing
Rich Palette of Processing and Logic Objects
CobraNet Audio
256 Channel, Low Latency, Fault Tolerant Digital
Audio Bus
Clear Front Panel LED Indication
Informative Front Panel Display
Bi-Directional Locate Functionality
12 Control Inputs and 6 Logic Outputs for GPIO
Integration
Soundweb London Interface Kit for Third Party
Control System Integration (Documentation)
HiQnet Device
Configuration, Control and Monitoring from
HiQnet London Architect
BSS AUDIO | 8760 S. Sandy Parkway | Sandy, UT 84070 U.S.A | Ph. +1 - 801-566-8800 | Fax +1 - 801-566-7662
Networked Signal Processors
bssaudio.com
Soundweb™ London BLU-800
T E C H N I C A L S P E C I F I C AT I O N S :
BSS AUDIO | 8760 S. Sandy Parkway | Sandy, UT 84070 U.S.A | - Ph. +1 801-566-8800 | Fax +1 - 801-566-7662
18-0654
Front Panel Led Indicators:
Per Input:
Signal Present, CLIP, SYNC/48V, I/O card type (IN, OUT, DIG, AEC)
Other:
LCD Display, Conductor active, Network Link active, Data Activity
Analog Inputs:
Up to 16 electronically balanced on Phoenix Combicon removable screw connectors
Mic/Line Inputs:
Nominal gain 0dB, electronically switchable up to +48dB,in +6dB steps
Input Impedance:
3.5k7
Maximum Input Level: +20dBu with 0dB input gain,+8dBu with 12dB gain
CMRR:
>75dB at 1KHz
Input Noise (E.I.N.):
<-128dBu typical with 1507 source
Phantom Power:
48V nominal, selectable per input
A/D Latency:
38.7/Fs
Digital Inputs:
Up to 16 AES/EBU or S/PDIF on Phoenix/Combicon removable screw connectors
Input Impedance:
110 ohm (AES/EBU), 75 ohm (S/PDIF)
Sample Rate:
48kHz or 96kHz
Sample Rate Conversion: 8kHz-96kHz
THD+N:
<-140dB
Latency:
3/Fso + (56.581/Fsi) + (55.658/Fso)
Analog Outputs:
Up to 16 electronically balanced on Phoenix/Combicon removable screw connectors
Maximum Output Level: +19dBu
Frequency Response:
20Hz-20KHz (+0.5dB/-1dB)
THD:
<0.01% 20Hz to 20KHz, +10dBu output
Dynamic Range:
108dB typical, 22Hz-22KHz unweighted
Crosstalk:
<-75dB
D/A Latency:
28/Fs
Digital Outputs:
Up to 16 AES/EBU or S/PDIF on Phoenix/Combicon removable screw connectors
Output Impedance:
110 ohm (AES/EBU), 75 ohm (S/PDIF)
Sample Rate:
48kHz or 96kHz
Sample Rate Conversion: 8kHz-96kHz
THD+N:
<-140dB
Latency:
3/Fso + (56.581/Fsi) + (55.658/Fso)
Control Ports:
12 inputs and 6 outputs
Control Input Voltage:
0 to 4.5v
Control Input Impedance: 4.7k7 to +5V (2-wire mode), >1M7 (3-wire mode)
Logic Output Voltage:
0 or +5V unloaded
Logic Output Impedance: 4407s
Logic Output Current:
10mA source, 60mA sink
Watchdog Output:
Phoenix/Combicon connector for failsafe control
Opto Output Current:
14mA maximum
Withstanding Voltage:
80V maximum (Off)
Series Impedance:
2207 (isolated)
Control Network:
Connectors:
RJ45 Ethernet connector
Maximum Cable Length: 100m/300ft on Category 5 cable between device and Ethernet switch
Digital Audio Bus:
Connectors:
2 x RJ45 Ethernet connectors
Maximum Cable Length: 100m/300ft on Category 5e cable between devices
Maximum Number of Nodes:
60
Latency Per Node:
4(+/-1)Fs
CobraNet™ Audio Network:
Connectors:
2 x RJ45 connectors
Maximum Cable Length: 100m/300ft on Category 5 cable between device and Ethernet switch
Power and Dimensions:
Mains Voltage:
100-240V AC, 50/60Hz
Power Consumption:
<35VA
BTU Rating:
<188 BTU/hr
Operating Temperature Range:
5 (41) to 35 (95) degrees C (degrees F)
Dimensions (H(U) x W x D):
1.75" (1U) x 19" x 12.5" (45mm x 483mm x 318mm)
Weight:
9 lbs / 4.1 kgs (estimated)
Networked Signal Processors
bssaudio.com
Soundweb London
™
Architects & Engineers Specifications
The Digital Signal Processor shall be a stand-alone unit of one rack space, capable of providing a fully-functional system with a total of 16 analogue inputs /
analogue outputs configurable by Input Cards and Output Cards in banks of 4, without the need for a dedicated, on-line computer system. The analogue inputs
shall have a remotely-adjustable gain stage prior to A/D conversion.
The system designer shall be provided complete flexibility in system configuration.
Combination Microphone / Line inputs shall be provided, together with channel-selectable 48 volt phantom power per input. The unit shall provide a tamper-proof
front-panel with no user-adjustable controls. Front panel LED indicators will provide monitoring of signal presence, clip and network status. Analogue / Digital
and Digital / Analogue conversion shall be by 24-bit A-D converters and 24-bit D-A converters to provide maximum operating headroom and performance. The
Dynamic Range shall be 105dB minimum (unweighted, 108dB A-weighted), with a THD figure of less than 0.01%.
Input and Output connections are provided via modular, Phoenix / Combicon style hardware. Mating connectors (Phoenix / Combicon MSTB 2.5 / 6-ST-5.08 or
equivalent) shall be supplied with each unit on delivery or in advance.
The Signal Processor shall also be fitted with a Peak Audio CobraNet™ CM-1 card that shall allow the unit to send and receive audio signals to and from other
CobraNet™ devices via a standard Ethernet network over Category 5 cable (as established in the TIA/EIA-568-B standard). This network shall be terminated on
RJ-45 connectors, and be stable over distances up to 100 metres between unit and Ethernet switch. The network shall allow system expansion at a later date through
the addition of further Signal Processors. The CobraNet™ card shall allow a maximum of 4 bundles of 8 channels. 48kHz and 96kHz CobraNet operation shall be
possible. The network also enables routing of control data between processors.
The Signal Processor shall be fitted with a digital audio bus on BLU-800, 320, 160 and 120 devices. The bus shall allow transfer of 256 channels of audio (at 48kHz
sample rate, 128 channels at 96kHz) on a point to point connection between devices using Category 5e cable terminated on RJ-45 connectors and be stable over
distances up to 100 metres between devices. The bus shall also feature redundancy by completing the connection in a ring
System configuration shall be by a Personal Computer, which may be disconnected after configuration without affecting installed operation of the unit. System
configurations shall be stored in each processing device, and these configurations shall not be limited by factory-only presets or pre-determined processing. It shall
be possible to configure a number of system presets, which may be recalled at any time via the PC or external control devices.
A front panel LCD will provide preset recall status and fault reporting. A non-latching switch on both front and rear panel will allow identification of the networked
processor on a host computer. The non-latching switches will be able to be illuminated to allow identification of a processor from the host computer.
The control software shall provide a palette of audio processing objects for use in system designs to include, but not be restricted to: Crossovers, Compressors,
Gates, Duckers, Expanders, Limiters, Gain blocks, Graphic Equalizers, Stereo Graphic Equalizers, Parametric Equalizers, Stereo Parametric Equalizers, Filters,
Metering points, Delays, Mixers, Matrix Routers, Matrix Mixers, Source Matrices, Tone Generators, and Source Selectors. The software shall provide the facility
to construct user-defined control panels incorporating elements of the processing object parameter controls. Multi-level password-based security shall protect the
integrity of the system.
The device configuration window shall provide a DSP gauge to inform the designer as to the percentage of DSP usage. The system design software shall be
compatible with Windows XP Home, Windows XP Professional and Windows 2000 operating systems.
It shall be possible to connect standard potentiometers and switches or control voltages to 12 control input ports enabling non-technical operators to change system
presets or variable parameters. An additional 6 control output ports shall provide logic outputs for purposes of signal indication, external switching systems, or other
similar system control applications. An opto-isolated failsafe indicator shall be provided on an open-collector output.
It shall also be possible to control and design the system network remotely using a PC connected into the system control Ethernet network.
An RS-232 port shall be provided to allow control of the unit from Multimedia Systems such as Crestron, Dataton, Extron, Avenger or other PC devices
communicating in a serial mode. The RS232 port on any device shall provide access to all devices that are properly networked together.
To aid in system management, the software shall provide a method of event logging so that system diagnostics are available. This event log shall include failures,
warnings and information notices, and shall display the time of the event occurrence, the device to which the event applies and the design file originally loaded.
There shall be an additional units available that will be able to expand the input and output capacity of the system. This unit shall be identical in networking
capabilities as the main signal processor, and feature identical input/output card configuration. The unit shall not feature any DSP resources.
There shall be an additional stand-alone units available without Peak Audio CobraNet CM-1 installed. This unit shall be identical in DSP resources as the main
signal processor, and feature identical input/output card configuration. A single RJ-45 Ethernet port is provided for connection to a network for DSP configuration or
control. The device will connect into the Ethernet control network with Category 5 cable.
There shall be available a programmable remote controller device, which shall provide up to 8 programmable buttons on a touchscreen liquid crystal display, a
rotary encoder and page select and navigation switches. The remote control shall offer 100 pages, each protectable with a user definable password. The remote
controller shall connect into the Ethernet control network with Category 5 cable. The remote control shall be capable of being housed in a standard NEMA-style,
3-Gang junction backbox.
There shall be available a programmable remote controller device, which shall provide 2 rotary encoders and programmable buttons. The remote controller shall
connect into the Ethernet control network with Category 5 cable. The remote control shall be capable of being housed in a standard NEMA-style, 3-Gang junction
backbox.
Smaller wall-mounting panels shall be available that allow control of sources and level (or similar functions) by connecting onto the control ports on the digital
signal processor housed in a standard UK light switch wall panel.
BSS AUDIO | 8760 S. Sandy Parkway | Sandy, UT 84070 U.S.A | Ph. +1 - 801-566-8800 | Fax +1 - 801-566-7662
18-0586
The digital signal processor shall be the BSS Audio Soundweb London BLU-80, BLU-800 and BLU-160.
The input/output expansion unit shall be the BSS Audio Soundweb London BLU-32, BLU-320 and BLU-120.
The stand-alone unit shall be the BSS Audio Soundweb London BLU-16.
The programmable touch screen remote controller shall be the BSS Audio Soundweb London BLU-10.
The programmable remote controller shall be the BSS Audio Soundweb London BLU-8.
The wall-mounting panels shall be the BSS Audio Soundweb BLU-3 and BLU-6.
bssaudio.com ITEM 31
Networked Signal Processors
Soundweb London
BLU-32
™
TM
Soundweb
BLU-32
4
2
3
1
4
IN
PRIMARY
SECONDARY
2
C
3
4 CONTROL INPUTS 9
OPTO 1 LOGIC OUTPUTS
+
–
10
6
11
R
12
R
S
+ –
S
+ –
S
+ –
S
+ –
S
+ –
S
+ –
S
+ –
S
+ –
OUT
LOCATE
RS232
ETHERNET
2
A
S
+ –
S
+ –
S
+ –
S
+ –
S
+ –
S
+ –
S
+ –
S
+ –
C
D
100-240VAC ~ 50/60Hz 35VA
T1AL-250V FUSE
1
3
B
1
C
BUDDYLINK / 48K
OVERVIEW:
The Soundweb London BLU-32 offers configurable I/O and CobraNet audio.
The BLU-32 is configurable through HiQnet™ London Architect. A rich palette of logic objects and a “drag and drop”
method of configuration provide a simple and familiar design environment.
This processor features CobraNet audio with primary and secondary ports for fault tolerance. Control is through a
separate Ethernet port which allows CobraNet and control networks to be easily separated or mixed depending upon
requirements.
Four card slots which accommodate analog inputs, analog outputs, digital inputs and digital outputs in banks of four
facilitate many different device I/O configurations.
Analog Input Cards provide software configurable gain in 6dB steps up to +48dB per channel and software selectable
Phantom Power per channel. Digital Input Cards and Digital Output Cards process AES/EBU and/or S/PDIF audio and
offer a variety of clocking and syncing options. (Further information about the I/O cards can be found on dedicated
datasheets)
Phantom Power, Sync, Signal Present and Clip information per channel is easily accessible, without the requirement for
a PC, from clear front panel LED indication. Device-specific information such as Device Name, Device Type, Firmware
Version Number, Time, IP Address and Subnet Mask is available from the front panel display. A bi-directional locate
function allows devices to be identified both from and within HiQnet London Architect.
12 Control Inputs and 6 Logic Outputs allow the BLU-32 to be integrated with GPIO compatible devices. The Soundweb
London Interface Kit, comprehensive documentation which details how Soundweb London systems can be integrated
with third party control systems, is included within the installation of HiQnet London Architect.
The BLU-32 and the other members of the Soundweb London family provide the building blocks of the perfectly tailored
system solution.
K E Y F E AT U R E S :
Four Input / Output Card Slots
Configurable Inputs / Outputs
Analog Inputs (with Phantom Power per
Channel)
Analog Outputs
Digital Inputs (AES/EBU and S/PDIF)
Digital Outputs (AES/EBU and S/PDIF)
Rich Palette of Logic Objects
CobraNet Audio
Clear Front Panel LED Indication
Informative Front Panel Display
Bi-Directional Locate Functionality
12 Control Inputs and 6 Logic Outputs for GPIO
Integration
Soundweb London Interface Kit for Third Party
Control System Integration (Documentation)
HiQnet Device
Configuration, Control and Monitoring from
HiQnet London Architect
Page 1 of 2
BSS AUDIO | 8760 S. Sandy Parkway | Sandy, UT 84070 U.S.A | Ph. +1 - 801-566-8800 | Fax +1 - 801-566-7662
Networked Signal Processors
bssaudio.com
Soundweb™ London BLU-32
T E C H N I C A L S P E C I F I C AT I O N S :
Front Panel Led Indicators:
Per Input:
Signal Present, CLIP, SYNC/48V, I/O card type (IN, OUT, DIG)
Other:
LCD Display, Conductor active, Network Link active, Data Activity
Analog Inputs:
Up to 16 electronically balanced on Phoenix Combicon removable screw connectors
Mic/Line Inputs:
Nominal gain 0dB, electronically switchable up to +48dB,in +6dB steps
Input Impedance:
3.5k7
Maximum Input Level: +20dBu with 0dB input gain,+8dBu with 12dB gain
CMRR:
>75dB at 1KHz
Input Noise (E.I.N.):
<-128dBu typical with 1507 source
Phantom Power:
48V nominal, selectable per input
A/D Latency:
38.7/Fs
Digital Inputs:
Up to 16 AES/EBU or S/PDIF on Phoenix/Combicon removable screw connectors
Input Impedance:
110 ohm (AES/EBU), 75 ohm (S/PDIF)
Sample Rate:
48kHz or 96kHz
Sample Rate Conversion: 8kHz-96kHz
THD+N:
<-140dB
Latency:
3/Fso + (56.581/Fsi) + (55.658/Fso)
Analog Outputs:
Up to 16 electronically balanced on Phoenix/Combicon removable screw connectors
Maximum Output Level: +19dBu
Frequency Response:
20Hz-20KHz (+0.5dB/-1dB)
THD:
<0.01% 20Hz to 20KHz, +10dBu output
Dynamic Range:
108dB typical, 22Hz-22KHz unweighted
Crosstalk:
<-75dB
D/A Latency:
28/Fs
Digital Outputs:
Up to 16 AES/EBU or S/PDIF on Phoenix/Combicon removable screw connectors
Output Impedance:
110 ohm (AES/EBU), 75 ohm (S/PDIF)
Sample Rate:
48kHz or 96kHz
Sample Rate Conversion: 8kHz-96kHz
THD+N:
<-140dB
Latency:
3/Fso + (56.581/Fsi) + (55.658/Fso)
Control Ports:
12 inputs and 6 outputs
Control Input Voltage:
0 to 4.5v
Control Input Impedance: 4.7k7 to +5V (2-wire mode), >1M7 (3-wire mode)
Logic Output Voltage:
0 or +5V unloaded
Logic Output Impedance: 4407s
Logic Output Current:
10mA source, 60mA sink
Watchdog Output:
Phoenix/Combicon connector for failsafe control
Opto Output Current:
14mA maximum
Withstanding Voltage:
80V maximum (Off)
Series Impedance:
2207 (isolated)
Control Network:
Connectors:
RJ45 Ethernet connector
Maximum Cable Length: 100m/300ft on Category 5 cable between device and Ethernet switch
CobraNet™ Audio Network:
Connectors:
2 x RJ45 connectors
Maximum Cable Length: 100m/300ft on Category 5 cable between device and Ethernet switch
Power and Dimensions:
Mains Voltage:
100-240V AC, 50/60Hz
Power Consumption:
<35VA
BTU Rating:
<120 BTU/hr
Operating Temperature Range:
5 (41) to 35 (95) degrees C (degrees F)
Dimensions (H(U) x W x D):
1.75" (1U) x 19" x 9” (45mm x 483mm x 228mm)
Weight:
7.3 lbs / 3.3 kgs (estimated)
BSS AUDIO | 8760 S. Sandy Parkway | Sandy, UT 84070 U.S.A | - Ph. +1 801-566-8800 | Fax +1 - 801-566-7662
18-0583
Page 2 of 2
Networked Signal Processors
bssaudio.com
Soundweb London
™
Architects & Engineers Specifications
The Digital Signal Processor shall be a stand-alone unit of one rack space, capable of providing a fully-functional system with a total of 16 analogue inputs /
analogue outputs configurable by Input Cards and Output Cards in banks of 4, without the need for a dedicated, on-line computer system. The analogue inputs
shall have a remotely-adjustable gain stage prior to A/D conversion.
The system designer shall be provided complete flexibility in system configuration.
Combination Microphone / Line inputs shall be provided, together with channel-selectable 48 volt phantom power per input. The unit shall provide a tamper-proof
front-panel with no user-adjustable controls. Front panel LED indicators will provide monitoring of signal presence, clip and network status. Analogue / Digital
and Digital / Analogue conversion shall be by 24-bit A-D converters and 24-bit D-A converters to provide maximum operating headroom and performance. The
Dynamic Range shall be 105dB minimum (unweighted, 108dB A-weighted), with a THD figure of less than 0.01%.
Input and Output connections are provided via modular, Phoenix / Combicon style hardware. Mating connectors (Phoenix / Combicon MSTB 2.5 / 6-ST-5.08 or
equivalent) shall be supplied with each unit on delivery or in advance.
The Signal Processor shall also be fitted with a Peak Audio CobraNet™ CM-1 card that shall allow the unit to send and receive audio signals to and from other
CobraNet™ devices via a standard Ethernet network over Category 5 cable (as established in the TIA/EIA-568-B standard). This network shall be terminated on
RJ-45 connectors, and be stable over distances up to 100 metres between unit and Ethernet switch. The network shall allow system expansion at a later date through
the addition of further Signal Processors. The CobraNet™ card shall allow a maximum of 4 bundles of 8 channels. 48kHz and 96kHz CobraNet operation shall be
possible. The network also enables routing of control data between processors.
The Signal Processor shall be fitted with a digital audio bus on BLU-800, 320, 160 and 120 devices. The bus shall allow transfer of 256 channels of audio (at 48kHz
sample rate, 128 channels at 96kHz) on a point to point connection between devices using Category 5e cable terminated on RJ-45 connectors and be stable over
distances up to 100 metres between devices. The bus shall also feature redundancy by completing the connection in a ring
System configuration shall be by a Personal Computer, which may be disconnected after configuration without affecting installed operation of the unit. System
configurations shall be stored in each processing device, and these configurations shall not be limited by factory-only presets or pre-determined processing. It shall
be possible to configure a number of system presets, which may be recalled at any time via the PC or external control devices.
A front panel LCD will provide preset recall status and fault reporting. A non-latching switch on both front and rear panel will allow identification of the networked
processor on a host computer. The non-latching switches will be able to be illuminated to allow identification of a processor from the host computer.
The control software shall provide a palette of audio processing objects for use in system designs to include, but not be restricted to: Crossovers, Compressors,
Gates, Duckers, Expanders, Limiters, Gain blocks, Graphic Equalizers, Stereo Graphic Equalizers, Parametric Equalizers, Stereo Parametric Equalizers, Filters,
Metering points, Delays, Mixers, Matrix Routers, Matrix Mixers, Source Matrices, Tone Generators, and Source Selectors. The software shall provide the facility
to construct user-defined control panels incorporating elements of the processing object parameter controls. Multi-level password-based security shall protect the
integrity of the system.
The device configuration window shall provide a DSP gauge to inform the designer as to the percentage of DSP usage. The system design software shall be
compatible with Windows XP Home, Windows XP Professional and Windows 2000 operating systems.
It shall be possible to connect standard potentiometers and switches or control voltages to 12 control input ports enabling non-technical operators to change system
presets or variable parameters. An additional 6 control output ports shall provide logic outputs for purposes of signal indication, external switching systems, or other
similar system control applications. An opto-isolated failsafe indicator shall be provided on an open-collector output.
It shall also be possible to control and design the system network remotely using a PC connected into the system control Ethernet network.
An RS-232 port shall be provided to allow control of the unit from Multimedia Systems such as Crestron, Dataton, Extron, Avenger or other PC devices
communicating in a serial mode. The RS232 port on any device shall provide access to all devices that are properly networked together.
To aid in system management, the software shall provide a method of event logging so that system diagnostics are available. This event log shall include failures,
warnings and information notices, and shall display the time of the event occurrence, the device to which the event applies and the design file originally loaded.
There shall be an additional units available that will be able to expand the input and output capacity of the system. This unit shall be identical in networking
capabilities as the main signal processor, and feature identical input/output card configuration. The unit shall not feature any DSP resources.
There shall be an additional stand-alone units available without Peak Audio CobraNet CM-1 installed. This unit shall be identical in DSP resources as the main
signal processor, and feature identical input/output card configuration. A single RJ-45 Ethernet port is provided for connection to a network for DSP configuration or
control. The device will connect into the Ethernet control network with Category 5 cable.
There shall be available a programmable remote controller device, which shall provide up to 8 programmable buttons on a touchscreen liquid crystal display, a
rotary encoder and page select and navigation switches. The remote control shall offer 100 pages, each protectable with a user definable password. The remote
controller shall connect into the Ethernet control network with Category 5 cable. The remote control shall be capable of being housed in a standard NEMA-style,
3-Gang junction backbox.
There shall be available a programmable remote controller device, which shall provide 2 rotary encoders and programmable buttons. The remote controller shall
connect into the Ethernet control network with Category 5 cable. The remote control shall be capable of being housed in a standard NEMA-style, 3-Gang junction
backbox.
Smaller wall-mounting panels shall be available that allow control of sources and level (or similar functions) by connecting onto the control ports on the digital
signal processor housed in a standard UK light switch wall panel.
BSS AUDIO | 8760 S. Sandy Parkway | Sandy, UT 84070 U.S.A | Ph. +1 - 801-566-8800 | Fax +1 - 801-566-7662
18-0586
The digital signal processor shall be the BSS Audio Soundweb London BLU-80, BLU-800 and BLU-160.
The input/output expansion unit shall be the BSS Audio Soundweb London BLU-32, BLU-320 and BLU-120.
The stand-alone unit shall be the BSS Audio Soundweb London BLU-16.
The programmable touch screen remote controller shall be the BSS Audio Soundweb London BLU-10.
The programmable remote controller shall be the BSS Audio Soundweb London BLU-8.
The wall-mounting panels shall be the BSS Audio Soundweb BLU-3 and BLU-6.
4U Ultimate Strength Series Roto-Rack by SKB Cases
Page 1 of 2
ITEM 32
4U Ultimate Strength Series Roto-Rack
company
product
SKU
SKB Cases
4U Ultimate Strength Series Roto-Rack
1SKB-R4
The Ultimate Strength Series is the best in American technology. With its roto molded tough shell, front
and rear lids, recessed heavy-duty twist latches, molded in handles, shock absorbing rubber feet and
the recognizable patented deep Roto-X pattern for solid stackability, these cases provide maximum
protection. The unique molded-in unbendable valance and steel threaded rails make the Ultimate
Strength Series Roto-Racks the new professional standard in the industry.
Backed by Our Exclusive:
• Million Mile Guaranty
Features & Benefits
•
•
•
•
•
•
•
•
•
Threaded steel rails
rear rails
Optional caster kit
Roto molded for strength
Interlocking X pattern for solid stackability
Front and rear full size lids
Recessed latches
Molded-in handles
Shock absorbing feet
Weights & Dimensions*
Rack Space Units
Rack Depth
Rack Depth Front To Back
Rack Depth Front To Rear Rail
Lid Depth
Product Weight
4
17.2500 in
19.8750 in
22.1250 in
2.0000 in
14.0000 lb
4
43.8150 cm
50.4825 cm
56.1975 cm
5.0800 cm
6.3503 kg
Accessories & Related Products
1SKB-1904
1SKB-RRK4
Standard Roto Caster Kit
4U Rear Rail Kit
http://www.skbcases.com/music/products/printspecs.php?id=138&c=115
5/14/2013
4U Ultimate Strength Series Roto-Rack by SKB Cases
Page 2 of 2
*Dimensions are for reference only. Some models may be pictured on this page and elsewhere with optional accessories or
equipment that are not included. Please consult with a SKB music product specialist at 800-410-2024 if you need assistance
or additional information. Product specifications are subject to change without notice.
Tuesday 14th of May 2013
www.skbcases.com/music
© SKB Cases Corportion
http://www.skbcases.com/music/products/printspecs.php?id=138&c=115
5/14/2013
AV EQUIPMENT RACK AT MIX POSITION
MIDDLE ATLANTIC BRK-12
1
NOTE:
CONNECT TO
ETHERNET ON
LONDON BLU 800
NOTE:
ICOM A TO A1
ICOM B TO B1
CLEARCOM PS702
NOTE:
CONNECT TO
PRIMARY ON
LONDON BLU 800
NOTE:
A1 FROM ICOM A
B1 FROM ICOM B
FLOORBOX PIT
AT MIX POSITION
OFE
LAN
AV EQUIPMENT RACK
MIDDLE ATLANTIC ERK-4425
Original Issue Date:
Date/Description
AV Solutions Group
Current Date:
Progress
X Design Development
Authorized Use:
No.
Revisions
Division
F
Discipline
ZAV
Drawing #
Zenith Job #:
Engineer:
Drawn By:
Sheet Description:
AV EQUIPMENT RACK
MIDDLE ATLANTIC ERK-4425
5060 Corbin Drive Bedford Hts, Ohio 44128
Phone- 216.395.5981 Fax- 216.395.5989
www.ZenithSystemsLLC.com
Sheet #
05
Shelby City Schools
Shelby High School
AV System Functional
Auditorium Page 1
NOTE:
CONNECT TO
OFE LAN
NOTE:
CONNECT TO
FLOORBOX
UPSTAGE LEFT
1
NOTE:
CONNECT TO
PRIMARY ON
YAMAHA LS9-16
NOTE:
CONNECT TO
FLOORBOX
DOWNSTAGE LEFT
NOTE:
CONNECT TO
FLOORBOX
PIT
NOTE:
CONNECT TO
FLOORBOX
UPSTAGE RIGHT
NOTE:
CONNECT TO
LAN ON
YAMAHA LS9-16
NOTE:
CONNECT TO
FLOORBOX
DOWNSTAGE RIGHT
DRESSING
A-106C
DRESSING
A-106B
BACKSTAGE
TO
VOCAL
ROOM
TO
INSTRUMENT
ROOM
CONTROL
A-110
STORAGE
A-109B
TICKET
A-110D
TICKET
A-110B
STORAGE
A-109A
MAKE UP
A-106
CORRIDOR
A-108
STORAGE/SHOP A-107
VOLUME CONTROL
VESTIBULE
TICKET
BOOTHS
FRONT
FILL
RIGHT
SPEAKER
LEFT
SPEAKER
CENTER
CLUSTER
2
TYPICAL OF 2
PORTABLE AV EQUIPMENT RACK
SKB 1SKBR4
Original Issue Date:
Date/Description
AV Solutions Group
Current Date:
Progress
X Design Development
Authorized Use:
No.
Revisions
Division
F
Discipline
ZAV
Drawing #
Zenith Job #:
Engineer:
Drawn By:
Sheet Description:
AV EQUIPMENT RACK
MIDDLE ATLANTIC ERK-4425
5060 Corbin Drive Bedford Hts, Ohio 44128
Phone- 216.395.5981 Fax- 216.395.5989
www.ZenithSystemsLLC.com
Sheet #
06
Shelby City Schools
Shelby High School
AV System Functional
Auditorium Page 2
1
Ã
(AVR4)
2
TYPICAL OF 2
(AVR5)
3
(AVR6)
Original Issue Date:
Date/Description
AV Solutions Group
Division
R
Discipline
ZAV
Drawing #
Zenith Job #:
Engineer:
Drawn By:
Sheet Description:
Current Date:
Progress
X Design Development
Authorized Use:
No.
Revisions
5060 Corbin Drive Bedford Hts, Ohio 44128
Phone- 216.395.5981 Fax- 216.395.5989
www.ZenithSystemsLLC.com
Sheet #
02
Shelby City Schools
Shelby High School
AV Equipment Racks
Rack Elevations