Adjustable Swivel Ring Hangers FUNCTION: Designed for the suspension of non-insulated stationary pipe lines. The knurled insert nut that allows a vertical adjustment after installation, is tapped to NFPA reduced rod size standards. Fig. 141F has a layer of felt which separates the pipe from the hanger to reduce vibration and sound. APPROVALS: Underwriters’ Laboratories Listed in the U.S. (UL), Canada (CUL), and Factory Mutual Approved for sizes 3⁄4" to 8". Complies with Federal Specifications A-A-1192A (Type 10), and Manufacturers’ Standardization Society ANSI/SP-69 and SP-58 (Type 10). ORDERING: Specify pipe size and figure number. Pipe Size /2 /4 1 11/4 11/2 2 21/2 3 31/2 4 5 6 8 1 3 Rod Size A 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 1 /2 1 /2 1 /2 B 17/8 111/16 15/8 115/16 21/8 27/16 31/16 311/16 33/4 43/16 45/8 55/8 613/16 Adj. C 17/16 11/8 1 11/16 11/16 11/8 15/8 17/8 17/8 17/8 15/8 21/4 27/16 D E 23/4 21/2 21/2 213/16 31/8 35/16 315/16 49/16 45/8 51/16 55/8 61/2 715/16 31/16 31/16 33/16 39/16 37/8 43/8 53/8 65/16 65/8 75/16 83/8 913/16 121/4 Fig. 141 & 141F NFPA SWIVEL RING HANGER Fig. 141 PRE-GALVANIZED WITH FELT LINING Fig. 141F PRE-GALVANIZED Max. Rec. Wt. Each Load/lbs. (in lbs.) 300 300 300 300 300 300 525 525 525 650 1000 1000 1000 .10 .10 .10 .11 .11 .14 .19 .23 .25 .30 .50 .58 .90 Note: If ordering Fig. 141F felt lined hangers for pipe sizes of 31/2" or under, order the next largest size to allow for the thickness of the felt lining. MATERIAL: FUNCTION: Designed for the suspension of non-insulated stationary pipe lines. The knurled insert nut, allows for vertical adjustment after installation. Fig. 151F has a layer of felt which separates the pipe from the hanger to reduce vibration and sound. APPROVALS: Underwriters’ Laboratories Listed in the U.S. (UL) and Factory Mutual Approved for all sizes. Complies with Federal Specification A-A-1192A (Type 10), and Manufacturers’ Standardization Society ANSI/SP-69 and SP-58 (Type 10). ORDERING: Specify pipe size and figure number. Pipe Size 21/2 3 31/2 4 5 6 8 Rod Size A /2 /2 1 /2 5 /8 5 /8 3 /4 3 /4 1 1 B 23/4 31/8 35/8 37/8 43/8 55/16 615/16 Adj. C D E 11/4 11/8 11/2 11/4 13/8 2 25/8 311/16 4 45/16 415/16 55/8 611/16 85/16 51/8 57/8 65/8 71/8 81/2 101/8 127/8 Low carbon steel Fig. 151 & 151F SWIVEL RING HANGER Fig. 151 PRE-GALVANIZED WITH FELT LINING Fig. 151F PRE-GALVANIZED Max. Rec. Wt. Each Load/lbs. (in lbs.) 600 600 600 1000 1000 1250 1250 .33 .35 .37 .48 .57 1.06 1.32 Note: If ordering Fig. 151F felt lined hangers for pipe sizes of 31/2" or under, order the next largest size to allow for the thickness of the felt lining. MATERIAL: Low carbon steel PHD Manufacturing, Inc. • 44018 Columbiana-Waterford Road • Columbiana, OH 44408 Toll Free (800) 321-2736 • Phone: (330) 482-9256 • Fax: (330) 482-2763 • www.phd-mfg.com