Simple Fit Switching PIR Sensors
TECHNICAL SPECIFICATION
TECHNOLOGY
PIR
MAXIMUM RECOMMENDED MOUNTING HEIGHT
1.8m to 3m
RANGE
Cone-shaped detection pattern,
6m radius at 2.5m mounting height
Description
MK Simple Fit Sensors offer cost effective presence detection for lighting control in
small to medium areas. This one-box solution is easy to install and commission, and
requires no additional parts. Providing cost effective presence detection for lighting
control. Simple Fit dual mount sensors are easy to install and can deliver energy
savings of up to 70%*
6.0m
OPERATING VOLTAGE
AC220~240V/50Hz
RECOMMENDED CIRCUIT PROTECTION
16A
MAXIMUM LOAD
6A or 600W fluorescent lightling load capacity
FEATURES
●
Presence detection by passive infrared
●
Loading up to 6 Amps
●
Innovative dual mount system
requires only one sensor for either
flush or surface mount applications
●
Ability to wire more than 1 sensor in
parallel to a load
●
Ability to switch volt free loads
●
External programming dials enable
quick adjustment of time and lux
levels
●
Lens mask included to mask out any
areas of unwanted detection
●
Off delay adjustable between 5
seconds and 18 minutes following the
last observed movement after which
the lights switch off
PHOTOCELL
Approx. 5 - 1000 Lux
OFF DELAY
5sec - 18min
COLOUR
White (RAL9010)
MATERIAL/ABS
Flame retardant PC
IP RATING
Surface Mount: IP44
Flush Mount:
IP44 (Sensor section only)
IP20 (Ceiling Board onwards)
●
PIR Lens provides 360 degree
detection
●
Detection Range of up to 6m diameter
at 25°C at 2.5m mounting height
K5017
●
DEPTH REQUIRED BEHIND CEILING
50mm
Manual on / off override function
●
Mounting Height: Recommended
ceiling mount 1.8m to 3m
WEIGHT
269g
K5017
Flush and Surface Ceiling Mount PIR
Sensor in one
●
For flush mount, spring clips enable
ease of installation in ceilings with
thickness between 5mm and 20mm
●
Simple to switch between flush and
surface options
●
Surface mount can be fixed direct to
the ceiling or on to a circular conduit
or BESA box
●
All screws and fixings supplied
Dimensions (mm)
97.18mm
Flush Mount (Hole size 75mm to 80mm)
68mm
65.42mm
Max 500W
97.18mm
Max 600W
40.8mm
Max 2000W
114.63mm
SWITCHABLE LOAD
21.95mm
Max 120W
Max 110W
56mm
56mm
104,28
Surface Mount
For a full range of corresponding products,
104,18
44.45mm
66.72mm
4,17
Max 75W
2.4o
22.27mm
see pages 63-66 in the product selector.
485
17.92mm
56
WIRING DEVICES
WHITE
Sensors Technical
Technical Hotline
+44 (0)1268 563720
WHITE
WIRING DEVICES
Sensors Technical
mkelectric.co.uk
Simple Fit Switching PIR Sensors
TECHNICAL SPECIFICATION
TECHNOLOGY
PIR
MAXIMUM RECOMMENDED MOUNTING HEIGHT
1.8m to 3m
042924-001Cone-shaped
Rev.B_FM
Rev.A_FM
Sensor.qxp
detection pattern, Sensor_Art.qxp:50042924
50042925-001 Rev.B_SM
Sensor_Art.qxp:50042925
Re
RANGE
6m radius at 2.5m mounting height
K5015
6.0m
Description
OPERATING VOLTAGE
AC220~240V/50Hz
Specification
MK Simple Fit Sensors offer cost effective presence detection for lighting control
Specification
RECOMMENDED CIRCUIT PROTECTION
16A
Power requirement
AC 220 ~ 240V
MAXIMUM LOAD
6A or 1500W fluorescent/incadescent lightling load
capacity
Lighting load (Max)
PHOTOCELL
Approx. 30~200 Lux
K5016
in small to medium areas. These one-box solutions are easy to install and
commission,
also no additional parts are
/Power
50Hz requirement
ACrequired.
220 ~ 240V / 50Hz
The following versions are available:
6A or 1500W fluorescent/incandescent
Lighting
load (Max)
6A or 1500W fluorescent/incandescent
● Flush mounted K5015 – Spring Clips enable ease of installation in plasterboard
lighting load capability
lighting load capability
ceilings
Detection angle
Surface Mounted K5016 – Screw and Plug Fixings can be mounted direct to the
Up to 360° at 25°C
at 2.5mangle
Detection
Up to 360° at 25°C at 2.5m
ceiling or on to a square pattress box (K2160 WHI)
Detection range
5m radius at 2.5m
mounting
height
Detection
range
OFF DELAY
5sec - 40min
COLOUR
White
●
FEATURES
5m radius at 2.5m mounting height
Mounting height
Recommended ceiling
height
1.8m to 3m Recommended ceiling height 1.8m to 3
Mounting
height
Mounting type
Flush mount
MountingPassive
typephotocell holds lights
Flush
mount
off when area becomes occupied in
Isolation switch
control
K5015
AUTO/OFF
Isolation switch control
MATERIAL
Flame retardant PC
IP RATING
IP20
Advanced presence detection by passive infrared (PIR) technology
DEPTH REQUIRED BEHIND CEILING
100mm
Time adjustment
WEIGHT
105g excluding cable
Lux adjustment
K5016
Warm upWEIGHT
time
Adjustable 5
bright ambient conditions
AUTO/OFF
Off delay in minutes following the last observed movement after which
lightsminutes
switch off
seconds
~ 40
Time0-40adjustment
Adjustable 5 seconds ~ 40 minutes
Detection pattern and approx range in metres at floor level for 2.5m
6madjustment
Approx. 30 ~ 200Lux
Lux
30 shaped).
~ 200 Lux
mounting height (detectionApprox.
pattern is cone
About 1 minute
Protection degree
About 1 minute Warm up time
Dimensions
IP20
Protection degree
Safety
CE
CE
105g approx
K5015
Safety
Product Dimensions
IP20
K5016
Product Dimensions
86
mm
76
mm
11
486
86
mm
76
mm
54.5
mm
86
mm
11
Superior Switching PIR Sensors
TECHNICAL SPECIFICATION
TECHNOLOGY
PIR
DETECTION RANGE
10m Macro / 7m Micro at 2.5m mounting height
Aspect ratio
Macro = 4:1
Micro = 2.8:1
2.5m
7m
Micro
Micro
Micro
1.5m
7m
1.5m
SWITCHING CAPACITY
10A (Tungsten 6A)
PHOTOCELL RANGE (LUX)
Adjustable 10 to 1000 lux via K4098
DELAY TIME RANGE
Adjustable 5mins to 40 mins via K4098
IP RATING
IP4X
K5030F
Description
A range of high performance switching PIR sensors for dependable switching of
lighting loads.
FEATURES
●
High definition lenses, performance
optics and software are all optimised
to provide class leading sensitivity and
occupancy detection ensuring that the
lights are always on when required
●
Superior switching sensors deliver
highly sensitive micro detection
diameter of 7m within a 10m macro
detection diameter (When installed at
a mounting height of 2.5m)
●
Superior switching sensors include
integral adjustable active photocells
which will hold the lights off in
occupied areas or switch them off at a
given light level
●
Colour coded connectors make
superior switching sensors easy to
install and reduce wiring faults
●
The easy to use K4098 infrared
programming tool simplifies sensor
set up and commissioning
SUPPLY VOLTAGE
Mains 230V
TEMPERATURE RANGE
0-40 degrees
ACCESSORIES
K4098 Infrared programming tool required to adjust
sensor settings
K5030SM
Flush Mount
73mm
75mm
17.6mm
ø 87mm
Surface Mount
ø 93mm
107.6mm
ø 87mm
487
WIRING DEVICES
WHITE
Sensors Technical
Technical Hotline
+44 (0)1268 563720
WHITE
mkelectric.co.uk
Superior PIRs for
DALI or DSI Dimming
TECHNICAL SPECIFICATION
TECHNOLOGY
PIR
DETECTION RANGE
10m Macro / 7m Micro at 2.5m mounting height
K5040F
2.5m
Description
7m
Micro
Micro
Micro
1.5m
7m
1.5m
SWITCHING CAPACITY
10A (Tungsten 6A)
A range of high performance PIR sensors for dependable control of digital dimming
lighting loads.
FEATURES
●
High definition lenses, performance
optics and software are all optimised
to provide class leading sensitivity and
occupancy detection ensuring that the
lights are always on when required
●
Superior PIR sensors deliver highly
sensitive micro detection diameter
of 7m within a 10m macro detection
diameter (When installed at a
mounting height of 2.5m)
●
Dimming sensors include integral
photocells which will hold the lights
off in occupied areas or switch them
off at a given light level. Regulating
photocells enable a constant light
level to be maintained through digital
dimming
●
Automatic detection of DALI and
DSI digital dimming type luminaires
reduces commissioning time and the
potential for errors
●
The easy to use K4098 infrared
programming tool simplifies sensor
set up and commissioning
DIGITAL DIMMING
DALI or DSI (Auto detect)
ANALOGUE DIMMING
1-10V
PHOTOCELL RANGE (LUX)
Adjustable 100 to 1000 lux via K4098
DELAY TIME RANGE
Adjustable 5mins to 40mins via K4098
IP RATING
IP4X
SUPPLY VOLTAGE
Mains 230V
TEMPERATURE RANGE
0-40 degrees
ACCESSORIES
K4098 Infrared programming tool required to adjust
sensor settings
Flush Mount
73mm
75mm
17.6mm
ø 87mm
Surface Mount
ø 93mm
ø 87mm
488
K5040SM
Aspect ratio
Macro = 4:1
Micro = 2.8:1
107.6mm
WIRING DEVICES
Sensors Technical
Battenfit Switching
PIR Sensor
TECHNICAL SPECIFICATION
MAXIMUM RECOMMENDED MOUNTING HEIGHT
5.0m
RANGE
Cone-shaped detection pattern,
diameter (at floor level) = 2.4 x mounting height
K4047
Description
2.5m
Ideal for retrofit installations, the BattenFit sensor is a simple-to-fit control
solution for batten style luminaires which can deliver energy savings of up
to 70%
6.0m
OFF DELAY
1 minute – 40mins
10 second walk test mode
FEATURES
PHOTOCELL
Adjustable 50-5000 lux
Advanced presence detection by passive infrared (PIR) technology
OPERATING VOLTAGE
230V 50Hz
RECOMMENDED CIRCUIT PROTECTION
10 Amps
5-35
MAXIMUM LOAD
2A
A
COLOUR
White
5m
MATERIAL
Flame retardant PC/ABS
Off delay in hours following the last observed movement after which
lights switch off
Passive photocell holds lights off in bright ambient conditions.
Active photocell has the capability to switch lights off in occupied areas
Detection pattern and range in meters under normal operating
conditions
WEIGHT
100g
One Switch Manual input to turn luminaires on or off
IP RATING
IP65
Infrared programming enables easy commissioning and
re-commissioning via K4058
ACCESSORIES
K4098 Infrared programming tool required to adjust
sensor settings
IP
Detection Profile
Plan View
o
Detection pattern is a 360
cone shape. Diameter is
2.25 x the mounting height.
29
14
M20 x 1.5
Dimensions (mm)
IP65
The squares show the
arrangement of the detection
pattern. Sensitivity is greater
when approaching at a
tangent rather than heading
towards the centre.
BATTEN LUMINAIRE
14
2.5m
97o
DETECTION ZONE
2.5m
5m
Direction of most
commonly used
entry into detection
zone, i.e. start of
corridor or doorway
5m
40
107
5.6m
600
489
WIRING DEVICES
WHITE
Sensors Technical
Technical Hotline
+44 (0)1268 563720
WHITE
WIRING DEVICES
Sensors Technical
mkelectric.co.uk
Ultrasonic Sensors
TECHNICAL SPECIFICATION
OPERATING VOLTAGE
230V 50Hz
MAXIMUM RECOMMENDED MOUNTING HEIGHT
5 metres
SWITCH CAPACITY
10 Amps – Incandescent lamps: 1500W max (230V)
TERMINAL CAPACITY
2 x 1.5mm or 1 x 2.5mm
K4030
Features
WEIGHT
148g
Active presence detection by ultrasonic technology
TIME DELAY
5, 10 or 15 mins
Passive photocell holds lights off in bright ambient conditions
POWER-UP CONDITION
select on or off
5-15
DETECTOR RANGE
adjustable
6m 13m
ON/OFF RANGES:
adjustable
ULTRASONIC FREQUENCY
40kHz
PHOTOCELL
adjustable 50 to 5000 lux
Description
The sensors control feature a movement
detector, photocell and 10 Amp load switching
element in one easily deployed housing. The
technology has been refined and improved
over many years of efficient, reliable service
in a wide range of industrial and commercial
environments. The latest designs use state-ofthe-art miniaturisation to pack the features into
a small, attractive yet rugged enclosure which
gives full field-of-view adjustment. Detectors are
available for surface or semi-flush mounting.
Off delay in minutes following the last observed movement after which the
lights switch off
Detection pattern and range in metres under normal operating conditions
Dimensions
K4030 – Surface version
K4030 – Semi Flush version
The back-box can be secured directly
to a hard surface or to a conduit stop
end box.
Use a hole saw to drill a 76mm hole
into the ceiling tile. The flush ring is
designed to clamp the tile between its
two halves.
Ultrasonic sensors are general purpose, fully
automatic, directional presence detectors with
71mm
photocell. They save energy by switching off
60mm
lights in unoccupied areas and by holding lights
off in occupied areas which have adequate
natural light. They use a specially developed
ultrasonic radar to monitor the controlled space
for movement. This radar is sensitive enough
to respond to even very small movements thus
ensuring that lights are sustained whenever the
controlled space is occupied. If no movement 20mm
back
entry
has been detected for a pre-selected period, the
knockout
sensors switch the lights off until the next visitor
is detected.
490
K4031
Flush PlateFlush
& Clamp
Plate(K4078)
& Clamp (K4078)
simple
flush of
mounting
For simple For
flush
mounting
detectorof
todetector to
suspended suspended
ceilings. ceilings.
Max clamping
Maxdistance
clamping
– 25mm
distance – 25mm
71mm
60mm
60
mm
83
mm
60
mm
3 x side entry
3 x knockout
side entry knockout
20mm
back
entry
knockout
51mm
51mm
83
mm
120mm
120mm
A sensor
will
fit backplate
to its own or
backplate
or to
A sensor will
fit to its
own
to
a standard a25mm
standard
switch
25mm
sinking
switch
box.
sinking box.
Rear View Rear View
Ultrasonic sensors utilise ultrasonic radar to monitor a space for movement. This
involves transmitting an ultrasound signal and examining the reflected signal for
frequency variations called “doppler shifts”. The transmitted signal is more quickly
dissipated in open space and squeezed out by constraining walls and ceilings. The
range of the detector also depends upon the type of movement being observed:
for example, walking activity can be observed at a greater distance than the slight
hand or body movement to be expected from a person working at a desk. Note that
detectors can see behind themselves slightly so must be inset in a storage aisle or
corridor application.
Hand-Held Programming Tools
TECHNICAL SPECIFICATION
TRANSMISSION METHOD
Infrared
RANGE
15m approx
BATTERY
3Vdc CR2032 Lithium Button Cell
EXPECTED BATTERY LIFE
3 years
STORAGE TEMPERATURE
-25°C to +70°C
K4058
OPERATING TEMPERATURE
0°C to 40°C
IP RATING
4X
APPROVAL
CE
DIMENSIONS
K4058:87mm (H) x 40mm (W) x 7mm (D)
K4059:100mm (H) x 50mm (W) x 7mm (D)
WEIGHT
20g approx
K4059
Description
MK sensors* feature a range of programmable parameters which can be adjusted using
a simple, low cost hand-held programming controller.
*Not including Simple fit
FEATURES K4058
●
3 simple time-delay settings (5
minutes/10 minutes/20 minutes)
●
Presence detection mode
●
●
●
FEATURES K4059
●
4 simple time-delay settings (5
minutes/10 minutes/20 minutes/40
minutes)
Absence detection mode
●
Presence detection mode
Enable/disable photocell
●
Absence detection mode
Walk-test feature
●
Enable/disable photocell
●
Walk-test feature
●
Set regulating light level - when used
in conjunction with a suitable lux meter
●
Restore button functionality - press
& hold reverts to factory default,
short press reverts back to last
configuration
●
Lamp burn-in
491
WIRING DEVICES
WHITE
Sensors Technical
Technical Hotline
+44 (0)1268 563720