Timers
P111644
P111643
P111642
Just enough light !
Time switches
Contents
Presentation
2
Choice table
MIN, MI Ns, MINp, MINt and PRE switch-off warning
4
Technical data
MIN
MINs
MINp, MINt
PRE switch-off warning
5
6
7
8
Dimensions
UT00656EN
MIN, MINs, MINp, MINt and PRE switch-off warning
9
version: 2.1
Just enough light!
By automatically switching off lighting, ventilation,
etc. after a user-set time delay, MIN timers provide
both savings and comfort.
Since several control push-buttons may be
connected, MIN timers are ideal for controlling
stairway lighting.
Energy savings
Whatever the type of building or infrastructure, it is important nowadays
to optimize your energy costs. With the MIN timer’s adjustable time delay,
you can optimize your lighting and avoid pointless consumption.
Energy savings can be improved using the MINt impulse relay function
to reduce even more the time the load is switched on.
Stairway, corridor
or hall lighting
Easy installation
Extremely simple to implement and install, the timers fit all electrical and
modular enclosures.
P111649
For MINs, MINp and MINt, mechanical
compatibility with the electrical distribution comb
busbar makes installation easier.
Convenient use
MIN timers are used to manage and control lighting whenever you wish.
One or more light sources may be controlled from one or more points.
They are controlled by simply pressing a push-button.
The switch-off warning function prevents you from finding yourself
in the dark at the end of the time delay.
version: 2.1
UT00656EN
P111648
> MIN
P111642
Electromechanical timer, adjustable time delay from 1 to 7 min.
Silent electronic timer, adjustable time delay from 0.5 to 20 min.
> PRE
P111646
Switch-off warning, only used with MIN and MINs.
P111643
P111644
UT00656EN
> MINs
> MINp
Silent electronic timer with switch-off warning, adjustable time delay
from 0.5 to 20 min.
> MINt
Silent electronic timer with switch-off warning and impulse relay function,
adjustable time delay from 0.5 to 20 min.
version: 2.1
Timers
MIN, MINs, MINp, MINt, PRE
Choice table
MIN, MINs
These timers allow closing and then opening of a contact in a determined time.
MINp, MINt
This timer allows closing and then opening of a contact in a determined time, and it
also provides warning that the lighting is about to be switched off by flickering of the
lamplight. (switch-off warning). The MINt timer is the same as MINp with an “impulse
relay” additional function (see ”MINt” technical data).
PRE
This is used in association with MIN or MINs timers and only on incandescent
lighting circuits (not used on fluorescent, fluocompact lamps and very low voltage
halogen lamps). It provides warning that the lighting is about to be switched off by
reducing the brightness by 50 % during the 20 to 60 s warning time.
Catalogue numbers
MIN
MINs
MINp
MINt
PRE
15363
CCT15232
CCT15233
CCT15234
15376
230 V AC
50 Hz
1 to 7 min.
230 V AC
50/60 Hz
0.5 to 20 min.
< 6 VA
16 A
-25 to +50 °C
2
■
Automatic
■
230 V AC
50/60 Hz
0.5 to 20 min.
1h
< 6 VA
16 A
-25 to +55 °C
2
■
Automatic
■
■
■
230 V AC
50/60 Hz
20 to 60 s
1 VA
16 A
-10 to +50 °C
2
■
Selector switch
230 V AC
50/60 Hz
0.5 to 20 min.
1h
< 6 VA
16 A
-25 to +55 °C
2
■
Automatic
■
■
Technical data
Voltage (+10 %, -15 %)
Frequency
Adjustable time delay
Long time delay
Consumption
Switching capacity (cos φ = 1)
Operating temperature
Width (9 mm modules)
1 screw connection per pole for cables up to 6 mm²
Selection of the type of connection (3 or 4 wires)
Mechanical compatibility with electrical distribution comb busbar
Switch-off warning function
Impulse relay function
version: 2.1
-10 to +50 °C
2
■
■
UT00656EN
MIN
P111648
Functions
These timers allow closing and then opening of a contact in a determined time.
Technical data
MIN.
b
v
v
b
b
b
b
b
b
b
b
Two operating modes triggered by switch on front face:
automatic mode:
operation in timing mode,
time delay adjustable from 1 to 7 min.,
setting in steps of 15 s using knob,
pressing a push-button renews the time delay.
manual override mode: constant lighting.
Voltage: 230 V AC ± 10 %.
Frequency: 50 Hz.
Consumption during operation: 1 VA maxi.
Consumption of connected luminous push-buttons: 50 mA maxi.
Degree of protection: IP 20B.
Operating temperature: -10 °C to +50 °C.
Contact rating: 16 A, cos φ = 1.
Load table:
Type of lighting
Max. power
230 V incandescent and halogen lamps
Non-corrected/ serial-corrected/ dual mounted
fluorescent tubes with conventional ballast
Fluocompact lamps with conventional ballast
Parallel-corrected fluorescent tubes
with conventional ballast
Fluorescent tubes with electronic ballast
Fluocompact lamps with electronic ballast
2300 W
2300 VA
2000 VA
1300 VA (70 F)
300 VA
9 x 7 W, 6 x 11 W, 5 x 15 W,
5 x 20 W
b Control circuit: connected luminous push-buttons; timer inoperative via selfprotection if consumption above 50 mA maximum.
b Switch-off warning: external via use of PRE product.
Connection
b Connection terminals: 1 screw connection per pole for cables up to 6 mm².
b Connection type: 3 or 4 wires with selector switch on the side of the product.
L
L
4 wires
L
4 wires
3
N
4
R
N
or
3 wires
L
3
N
4
N
A1
A2
3
or
R
3 wires
MIN + PRE
Catalogue number
Type
MIN
Specific shield for terminal blocks insulation
UT00656EN
version: 2.1
Cat. no.
15363
15359
Timers
MINs
P111642
Functions
These timers allow closing and then opening of a contact in a determined time.
Technical data
MINs.
b
v
v
b
b
b
b
b
b
b
b
b
b
b
Two operating modes triggered by switch on front face:
timer mode: time delay adjustable from 0.5 to 20 min.,
permanent mode: constant lighting.
Pressing on a push-button renews the time delay.
Voltage: 230 V AC +10 %, -15 %.
Frequency: 50/60 Hz.
Consumption during operation: < 6 VA
Consumption of connected luminous pushbuttons: 150 mA maxi.
Insulation class: class II.
Degree of protection: IP 20B.
Operating temperature: -25 °C to +50 °C.
Contact rating: 16 A, cos φ = 1.
Switch-off warning: external via use of PRE product.
Load table:
Type of lighting
Max. power
230 V incandescent and halogen lamps
Non-corrected/ serial-corrected/ dual mounted
fluorescent tubes with conventional ballast
Fluocompact lamps with conventional ballast
Parallel-corrected fluorescent tubes
with conventional ballast
Fluorescent tubes with electronic ballast
Fluocompact lamps with electronic ballast
2300 W
2300 VA
1500 VA
400 VA (42 μF)
300 VA
9 x 7 W, 7 x 11 W, 7 x 15 W, 7 x
20 W, 7 x 23 W
Connection
b Connection terminals: 1 screw connection per pole for cables up to 6 mm².
b Connection type: 3 or 4 wires with automatic selection of the control push-button
connection.
b Mechanical compatibility with electrical distribution comb busbars.
L
L
4 wires
L
4 wires
3
N
4
R
N
or
3 wires
L
3
N
4
N
A1
A2
3
or
R
3 wires
MINs + PRE
Catalogue number
Type
MINs
version: 2.1
Cat. no.
CCT15232
UT00656EN
MINp, MINt
P111643
Functions
This timer allows closing and then opening of a contact in a determined time,
and it also provides warning that the lighting is about to be switched off
by flickering of the lamplight. (switch-off warning). The MINt timer is the same as
MINp with an “impulse relay” additional function (see ”MINt”).
Technical data
P111644
MINp.
MINt.
b Time delay adjustable from 0.5 to 20 min.
b Three operating modes triggered by switch on front face:
v timer mode with warning function built into the device. The lamp blinks 40 and 30
s before the end of the time delay,
v timer mode mode without ”switch-off warning” function,
v permanent mode : constant lighting.
b Timer mode operation:
v pressing a push-button for longer than 2 s: lighting will last for 1h.
Pressing again a push-button for less than 2 s relaunch the time delay of 1h
and pressing again a push-button for more than 2 s switches off the light.
v for MINp, pressing a push-button for less than 2 s launch the pre-set time delay,
pressing again a push-button for less than 2 s relaunch the pre-set time delay,
v for MINt, pressing a push-button for less than 2 s launch the pre-set time delay,
pressing again a push-button for less than 2 s, switches off the light (impulse relay
mode).
b Voltage: 230 V AC +10 %, -15 %.
b Frequency: 50/60 Hz.
b Consumption during operation: < 6 VA.
b Consumption of connected luminous push-buttons: 150 mA maxi.
b Insulation class: class II.
b Degree of protection: IP 20B.
b Operating temperature: -25 °C to +50 °C.
b Contact rating: 16 A, cos φ = 1,
b Load table:
Type of lighting
230 V incandescent and halogen lamps
Non-corrected/ serial-corrected/ dual mounted fluorescent
tubes with conventional ballast
Fluocompact lamps with conventional ballast
Parallel-corrected fluorescent tubes
with conventional ballast
Fluorescent tubes with electronic ballast
Fluocompact lamps with electronic ballast
Max. power
3600 W
3600 VA (1)
1500 VA (1)
1200 VA (120 μF) (1)
1000 VA
34 x 7 W, 27 x 11 W,
24 x 15 W, 22 x 23 W
(1) The ”switch-off warning” function is not available for these types of loads.
Connection
b Connection terminals: 1 screw connection per pole for cables up to 6 mm².
b Connection type: 3 or 4 wires with automatic selection of the control push-button
connection.
b Mechanical compatibility with electrical distribution comb busbars.
L
4 wires
L
3
N
4
R
N
or
3 wires
Catalogue numbers
Type
MINp
MINt
UT00656EN
version: 2.1
Cat. no.
CCT15233
CCT15234
Timers
PRE
switch-off warning
P111646
Functions
This is used in association with MIN or MINs timers and only on incandescent
lighting circuits (not used on fluorescent, fluocompact lamps and very low voltage
halogen lamps). It provides warning that the lighting is about to be switched off by
reducing the brightness by 50% during the 20 to 60 s warning time.
Technical data
PRE.
b Only to be used with the MIN et MINs timers.
b 50 % reduction in brightness during warning time.
b Time adjustable from 20 to 60 s.
b Voltage: 230 V AC ± 10 %.
b Frequency: 50/60 Hz.
b Operating temperature: -10 °C to +50 °C.
b Maximum power: 2300 W for incandescent lamps only.
b Not compatible with fluorescent lamps, fluocompact lamps and very low voltage
halogen lamps.
Connection
b Connection terminals: 1 screw connection per pole for cables up to 6 mm².
b Connection type: 3 or 4 wires.
L
A1
A2
min
3
R
N
Catalogue numbers
Type
PRE
Specific shield for terminal blocks insulation
version: 2.1
Cat. no.
15376
15359
UT00656EN
MIN, MINs, MINp, MINt, PRE
Dimensions
MIN
5
63
18
38
83
83
45
MINs, MINp, MINt
6
60
44
18
24
85 89
45 72
PRE
60
6
44
18
89
UT00656EN
version: 2.1
26
45 73
Notes
10
version: 2.1
UT00656EN
Notes
UT00656EN
version: 2.1
11
Notes
12
version: 2.1
UT00656EN
35, rue Joseph Monier
CS 30323
F- 92506 Rueil Malmaison Cedex
RCS Nanterre 954 503 439
Capital social 896 313 776 €
www.schneider-electric.com
UT00656EN
As standards, specifications and designs change from time to time, please ask for confirmation
of the information given in this publication.
This document has been printed on ecological paper
Design: Schneider Electric
Photos: Schneider Electric
Printed:
© 2010 - Schneider Electric - All rights reserved.
Schneider Electric Industries SAS
01-2010