ENGLISH
CAT5 VIDEO INTERCOM SYSTEM
Quick Installatin Manual
C5-ENG-MR6AT3-V1 090S604
Read this manual through before
installation and doing any operation.
ATTENTION:
This is an Quick Installation Manual, addressing Wiring and
Programming of the standard one-building intercom system,
for the complete and advanced multi-building systems, please
visit our website at www.extel.com?? for the detail technical
documents.
-1-
CONTENT
1. System Wiring ------------------------------------3
2. MR6L Doorstation Installation------------------4
3. C5-F4 Distributor Installation-------------------6
4. AT3 Monitor Installations and Settings-------7
5. Power Supply and Cable------------------------8
6. System Configurations(MR6L)-----------------9
7. Specifications-------------------------------------13
-2-
1. System Wiring
Connect to next C5-F4
C5-F4
C5-F4
ML-ML+
L+ L- L+ L- ML+ ML- P+ P+
ON
-
18 V DC lock
P+ P-
SW1
OFF
MR6L
PS2
-3-
1
2
3
4
5
6
7
8
9
*
0
#
2. MR6L Doorstation Installation
The MR6L doorstation is a digital station with 128*128 pixels
LCD screen, color CCD camera, night view LED, and digital
keypad.
Visitors can call the apartment by dial the room number on the
keypd or search the namelist on the screen to call. (When the
doorstation is in standby, press '9#' to display the user namelist,
use the '8' / '0' key to scroll to last/next page, use the 1 to 7 key
to call the corresponding room)
Users can open the door by using the Unlock Code(the door
open password). When the doorstation is in standby, press '#'
key, then input the 4 digit password to open the door.
Microphone
Camera Lens
Night view LED
LCD screen
1
2
3
4
5
6
7
8
9
*
0
#
Digital Keypad
Loudspeaker
-4-
How to open the back cover:
How to adjust the camera angle:
Mounting Raincover and MR6L:
6
14
m
m
step 1: fixed the
Raincover on the wall
step 2: put MR6L
into the Raincover
382 mm
step 3: screw the
block
step 4: plug in
the block cover
42
mm
-5-
3. C5-F4 Distributor Installation
The C5-F4 is a 4 output distributor for the C5 system. There are
two mounting measures: bar mounting or dirrect wall mounting.
140mm
P+ P-
Trunk Bus
D
C
B
A
88mm
C5-F4 distributor
A/B/C/D port: Connect to Monitors
Trunk Bus: Bus cable input/output. Connect to last
C5-F4(or doorstation), and connect to next C5-F4
Power
In-use
Data
P-: Power negative input. (Ground)
P+: Power positive input. (15~18V DC)
32mm
36mm
upward
62mm
70mm
HI
13mm
120
set to 120 for the last C5-F4
on the building, the others
must be set to HI.
84mm
Dirrect wall mounting:
Bar mounting:
-6-
4. AT3 Monitor Installations and Settings
1. AT3 monitor mounting:
2. AT3 monitor room address(room code) and time settings:
1.Power the monitor. Enter
into the Main --> setup
--> installation --> (input
password: 2412) to open
the configuration page.
2. Input Numbers: use the
+ / - button to add/minus
current digit, press ►button
to switch to next digit, after
4 digit are input, press ►
button again to confirm.
3. select and enter Room
Address... item to modify
the room code.
alarm
monitor
setup
intercom
setup
Doorstation Tone
--
01
Camera Tone
--
10
Guard unit Tone
--
05
No Disturb Set
--
off
Installation...
Exit
exit
H o m e I n t e l l eg e n t S y s t e m
H o m e I n t e l l eg e n t S y s t e m
installation
Alarm in/out delay
--
40
Date and Time set...
Room Address...
Other settings...
Informations...
2412
Password: 0
***
1
2
3
4
5
*
Exit
H o m e I n t e l l eg e n t S y s t e m
H o m e I n t e l l eg e n t S y s t e m
3. Change AT3 monitor language:
1. Get into the main page, when the 'setup' item is
highlighted, press and hold the UNLOCK button for 3
seconds to get into the Language select page.
2. Use the + / - button to scroll up/down, press ► button
to confirm the selected language.
-7-
alarm
monitor
intercom
setup
exit
H o m e I n t e l l eg e n t S y s t e m
6
7
8
9
0
#
5. Power Supply and Cables
The PS2 is the power supply for the system. It provides the power for the
doorstation, distributors, monitors and electronic lock.
The maximum number of monitors it can support is 20, that is to say, if there are
more than 20 moniotrs in the building, additional power supply is needed.
ML+, ML- of door station
E-lock (power-off-to-unlock type, 13~16V DC)
P+, P- of the door
station or distributor
E-lock (power-on-to-unlock type, 18V DC)
ON OFF
LK-TEST
SW3
L+ L-
L+ L- ML+ML- P+ P-
AC-IN
UNLOCK
18V-OUT
DC-OUT
SW1
ON
OFF
13~15V-OUT
BAT+
BAT-
AC
AC
PTR1
GND AC
AC
287 mm
VR1
100~240 V AC
247 mm
Cables and distance:
Power supply cable: RVVP 2*1.0 mm2
Distance: from doorstation to the last distributor: 600 m Max.
Data Cable: Catalogue-5 cable, 0.5 mm2+
Distance: from doorstation to the last distributor: 200m Max.
from distributor to monitor: 30m Max.
-8-
6. System Configurations(MR6L)
1. About room code(address):
Room Code(also called room address) is a code asign to each monitor, to didentify
deferent monitors; each monitor have a unique room code in one buidling.(see the
AT3 monitor installation and settings section to set room code)
2. About Debug State:
All settings of the doorstation will be done by getting into the Debug State.
> > D E B U G S TAT E < <
--------------------------#-# Program Guide
0-# Redial Last Nbrs
1-# Download from PC
2 - # D e b u g To o l s
[9008]
1
4
7
#
2
5
8
0
3
6
9
*
---------Options---------< > Vo l u m e A d j u s t
< > Auto Dial Back
< > Display Net Data
< ●> D i s p l a y A l a r m
< > Guard Unit Online
---------------------------
System Ready
System Ready
Video Entry System
Video Entry System
When Door Station is in
standby, press '#' key
input '9008', then
input the Admin Code.
(66666666 by default)
Video Entry System
Debug State menu is
launched
When the screen is Debug State, press '#9009' to exit.
3. About Default Set:
The Default Set is very important. When the settings of the doorstation is totally
mess up in anyway, the most quick and easy way to solve the problem is to launch
the default setting of the doorstation. The default settings is already have all the right
settings for one-building system, that means the system will work normally without
any additional settings.
> > D E B U G S TAT E < <
--------------------------#-# Program Guide
0-# Redial Last Nbrs
1-# Download from PC
2 - # D e b u g To o l s
---------Options---------< > Vo l u m e A d j u s t
< > Auto Dial Back
< > Display Net Data
< ●> D i s p l a y A l a r m
< > Guard Unit Online
>> Program Guide <<
---------------------------
[1] Configuration
---------------------------
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
-1.
-2.
-3.
-4.
-5.
-6.
-7.
-8.
-9.
Configuration
Unlock Setting
Monitor Program
Information
Operating Options
Access Security
Card Management
System Maintain
Advanced Config
Net Address [001]
Multi DS Mode [0]
Unlock Timing [1]
Monitoring Nbrs [2]
Intercom Video [1]
Camera Power On [0]
Doorplate Mode [1]
Admin. Code
Default Set
---------------------------
--------------------------Press 1~9 to select
* Back
--------------------------Press 1~9 to select
* Back
Video Entry System
Video Entry System
Video Entry System
In Debug State, press
'#' key twice
In Program Guide, press
'1' key
-9-
press '9' key, then input
Admin Code and'#'to confirm
4. Change Admin Code(administrator password):
The Admin Code is the password to access the doorstation Debug State. The default
Admin Code is '66666666'. Note that if the Default Set have been applied, the Admin
Code will also be set to default.
> > D E B U G S TAT E < <
--------------------------#-# Program Guide
0-# Redial Last Nbrs
1-# Download from PC
2 - # D e b u g To o l s
---------Options---------< > Vo l u m e A d j u s t
< > Auto Dial Back
< > Display Net Data
< ●> D i s p l a y A l a r m
< > Guard Unit Online
>> Program Guide <<
---------------------------
[1] Configuration
---------------------------
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
-1.
-2.
-3.
-4.
-5.
-6.
-7.
-8.
-9.
Configuration
Unlock Setting
Monitor Program
Information
Operating Options
Access Security
Card Management
System Maintain
Advanced Config
Net Address [001]
Multi DS Mode [0]
Unlock Timing [1]
Monitoring Nbrs [2]
Intercom Video [1]
Camera Power On [0]
Doorplate Mode [1]
Admin. Code
Default Set
---------------------------
--------------------------Press 1~9 to select
* Back
--------------------------Press 1~9 to select
* Back
Video Entry System
Video Entry System
Video Entry System
In Debug State, press
'#' key twice
press '1'
press '8'
>> [1][8]
Change Admin Code
Input the new Admin
Code and then press
'#'key to confirm
--------
<********>
* Back
# Save
Video Entry System
5. Change Unlcok Code:
There are two Unlock Code can be used, user can use any one of them to open the
door. there are '1111' and '2222' by default.
> > D E B U G S TAT E < <
--------------------------#-# Program Guide
0-# Redial Last Nbrs
1-# Download from PC
2 - # D e b u g To o l s
---------Options---------< > Vo l u m e A d j u s t
< > Auto Dial Back
< > Display Net Data
< ●> D i s p l a y A l a r m
< > Guard Unit Online
>> Program Guide <<
---------------------------
[2] Unlock Setting
---------------------------
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
-1.
-2.
-3.
-4.
-5.
-6.
-7.
-8.
Configuration
Unlock Setting
Monitor Program
Information
Operating Options
Access Security
Card Management
System Maintain
Advanced Config
Unlock Code 1 [1111]
Unlock Code 2 [2222]
Code Error Alert [0]
Code Mode [1]
Code Range ...
Code Check ...
Code Nbrs [0]
Change Program Code
---------------------------
--------------------------Press 1~9 to select
* Back
--------------------------Press 1~9 to select...
* Back
Video Entry System
Video Entry System
Video Entry System
-10-
6. Change doorstation language:
There are 8 operating languages can be selected:
0. Chinese
1. English
2. French
3. Portuguese
> > D E B U G S TAT E < <
--------------------------#-# Program Guide
0-# Redial Last Nbrs
1-# Download from PC
2 - # D e b u g To o l s
---------Options---------< > Vo l u m e A d j u s t
< > Auto Dial Back
< > Display Net Data
< ●> D i s p l a y A l a r m
< > Guard Unit Online
4. Spanish
5. German
6. Italian
7. Dutch
>> Program Guide <<
---------------------------
[9] Advanced Config
---------------------------
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
-1.
-2.
-3.
-4.
-5.
-6.
-7.
-8.
-9.
Configuration
Unlock Setting
Monitor Program
Information
Operating Options
Access Security
Card Management
System Maintain
Advanced config
To n e S e l e c t
Image Memo
Vo i c e M e m o
Name List
HMC
M o n i t o r Ve r s i o n
Call Mode
L ad nmgi u
A
n a. gCeo d e
Timing
[11]
[0]
[0]
[1]
[0]
[0]
[0]
[1]
---------------------------
--------------------------Press 1~9 to select
* Back
--------------------------Press 1~9 to select
* Back
Video Entry System
Video Entry System
Video Entry System
In Debug State, press
'#' key twice
press '9'
press '8'
>>[9][8]
Language
Input the number for each
language according to the
language table, press '#' to
confirm
(0~7)
* Back
7. Name List function:
#Save
Video Entry System
The namelist can be eddit by using the digital keypad of the doorstation, the input
method is similar as mobile phones. By default, the namelist function is on.
> > D E B U G S TAT E < <
--------------------------#-# Program Guide
0-# Redial Last Nbrs
1-# Download from PC
2 - # D e b u g To o l s
---------Options---------< > Vo l u m e A d j u s t
< > Auto Dial Back
< > Display Net Data
< ●> D i s p l a y A l a r m
< > Guard Unit Online
>> Program Guide <<
---------------------------
[9] Advanced Config
---------------------------
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
-1.
-2.
-3.
-4.
-5.
-6.
-7.
-8.
-9.
Configuration
Unlock Setting
Monitor Program
Information
Operating Options
Access Security
Card Management
System Maintain
Advanced config
To n e S e l e c t
Image Memo
Vo i c e M e m o
Name List
HMC
M o n i t o r Ve r s i o n
Call Mode
Admin. Code
Timing
[11]
[0]
[0]
[1]
[0]
[0]
[0]
---------------------------
--------------------------Press 1~9 to select
* Back
--------------------------Press 1~9 to select
* Back
Video Entry System
Video Entry System
Video Entry System
-11-
To use the namelist function, the Name List item must be set to
'1'(enable), which is the default setting.
>>[9][4]
>>[9][4].2 Name List
[Add_008]
Name List
1. Add
2. Modify
-
3. Initialise
Line 1:
_
[
]
Line 2:
[
]
(0~2)
Press 1~3 to select
* Back
#Save
Video Entry System
Press '2#' to enter
* Back
#Save
Video Entry System
(123)
* Back
#Save
Video Entry System
Press '1' to add new names, press '2' to modify the
existing names, press '3' to initialise to the default.
The first 4 digit are for the Room Code input(the address of the room), after 4 digit
have been input, it will switch to Line 1 and the input mode will switch to ABC input
mode automatically. Line 2 is for the names that are too long for one line. After the
name has been input, press '#' to save.
Button 1:
Button 2:
Button 3:
Button 4:
Button 5:
Button 6:
Button 7:
Button 8:
Button 9:
Button * :
Button 0:
Switch the letter between capitalization and lowercase.
A, B, C, (a, b, c)
D, E, F, (d, e, f)
G, H, I, (g, h, i)
J, K, L, (j, k, l)
M, N, O, (m, n, o)
P, Q, R, S, (p, q, r, s)
T, U, V, (t, u, v)
W, X, Y, Z, (w, x, y, z)
Cancel
Space blank, İ, Ş, Ç, Ü, Ğ, Ö
-12-
7. Specifications
Doorstation:
●● Power supply: DC 15~18V (supplied by PS2)
●● Camera Lens
1/3 inch color CCD
●● Power consumption:
Standby 0.5W; Working status 15W
●● Screen:
128*128 pixels LCD
●● Video signal:
1Vp-p, 75Ω, CCIR standard
●● Wiring:
6 wires, polar
Distributor:
●● Power supply: ●● Power consumption:
DC 15~18V (supplied by PS2)
Standby 0.3W; Working status 3W
Monitor:
●● Power supply for indoor monitor: ●● Power consumption:
DC 15~18V (supplied by system)
Standby 0.5W; Working status 15W (for kits)
●● Monitor screen:
5 Inch color TFT-LCD
●● Display Resolutions:
960(R, G, B) x 234 pixels
●● Video signal:
1Vp-p, 75Ω, CCIR standard
●● Wiring:
6 wires, polar
-13-
The design and specifications can be changed without notice to the
user. Right to interpret and copyright of this manual are preserved.
C5-ENG-MR6AT3-V1 090S604