FLOOR TREATMENT
09610
BonaKemi USA Inc.
14805 E. Moncrieff Place
Aurora, CO 80011
Phone: (800) 872-5515
Phone: (303) 371-1411
Fax: (303) 371-6958
E-mail: gerry.mueller@bona.com
www.bonakemi.com
This MANU-SPEC® utilizes the Construction Specifications Institute (CSI) Manual of Practice, including
MasterFormat™, SectionFormat™ and PageFormat™. A MANU-SPEC is a manufacturer-specific proprietary
product specification using the proprietary method of specifying applicable to project specifications and master
guide specifications. Optional text is indicated by brackets [ ]; delete optional text in final copy of specification.
Specifier Notes typically precede specification text; delete notes in final copy of specification. Trade/brand names
with appropriate symbols typically are used in Specifier Notes; symbols are not used in specification text. Metric
conversion, where used, is soft metric conversion.
This MANU-SPEC specifies finish systems for hardwood sports floors. These products are manufactured by
BonaKemi USA Inc. Revise MANU-SPEC section number and title below to suit project requirements, specification
practices and section content. Refer to CSI MasterFormat for other section numbers and titles.
SECTION 09610
FLOOR TREATMENT
(SPORT FLOOR FINISH PRODUCTS)
PART 1 GENERAL
1.01 SUMMARY
A.
Section Includes: Finish systems for hardwood sports floors.
Specifier Note: Revise paragraph below to suit project requirements. Add section numbers and titles per CSI MasterFormat and
specifier’s practice.
B.
Related Sections:
1.
Division 9 Sections: Wood Flooring.
Specifier Note: Article below may be omitted when specifying manufacturer’s proprietary products and recommended installation.
Retain Reference Article when specifying products and installation by an industry reference standard. If retained, list standard(s)
referenced in this section. Indicate issuing authority name, acronym, standard designation and title. Establish policy for indicating
edition date of standard referenced. Conditions of the Contract or Division 1 References Section may establish the edition date of
standards. This article does not require compliance with standard, but is merely a listing of references used. Article below should list
only those industry standards referenced in this section.
1.02 REFERENCES
A.
Maple Flooring Manufacturers Association (MFMA) approved.
Specifier Note: Article below includes submittal of relevant data to be furnished by Contractor before, during or after construction.
Coordinate this article with Architect’s and Contractor’s duties and responsibilities in Conditions of the Contract and Division 1 Submittal
Procedures Section.
1.03 SUBMITTALS
A.
General: Submit listed submittals in accordance with Conditions of the Contract and Division 1 Submittal Procedures
Section.
B.
Product Data: Submit manufacturer’s product data and application instructions.
C.
Closeout Submittals: Submit the following:
SPEC-DATA® and MANU-SPEC® are registered trademarks of Reed Elsevier Inc. The three part MANU-SPEC format conforms to the editorial style of the Construction
Specifications Institute and is used with their permission. The manufacturer is responsible for technical accuracy. ©2004 Reed Construction Data. All Rights Reserved.
FLOOR TREATMENT
09610
BonaKemi USA Inc.
1.
Warranty documents specified herein.
Specifier Note: Article below should include prerequisites, standards, limitations and criteria that establish an overall level of quality for
products and workmanship for this section. Coordinate article below with Division 1 Quality Assurance Section.
1.04 QUALITY ASSURANCE
Specifier Note: Paragraph below should list obligations for compliance with specific code requirements particular to this section.
General statements to comply with a particular code are typically addressed in Conditions of the Contract and Division 1 Regulatory
Requirements Section. Repetitive statements should be avoided.
A.
Applicator Qualifications: Utilize a professional contractor trained in application of the manufacturer’s sport floor products.
B.
Regulatory Requirements and Approvals: [Comply with clean air requirements.] [Specify applicable requirements of
regulatory agencies.].
Specifier Note: Article below should include special and unique requirements. Coordinate article below with Division 1 Product
Requirements Section.
1.05 DELIVERY, STORAGE & HANDLING
A.
General: Comply with Division 1 Product Requirement Section.
B.
Delivery: Deliver materials in manufacturer’s original, unopened, undamaged containers with identification labels intact.
C.
Storage and Protection: Store materials protected from exposure to harmful environmental conditions and at temperature
and humidity conditions recommended by the manufacturer.
Specifier Note: Coordinate article below with Conditions of the Contract and with Division 1 Closeout Submittals (Warranty) Section.
Coordinate warranty requirements of this section with warranty requirements of Floor Treatment Section.
1.06 WARRANTY
A.
Project Warranty: Refer to Conditions of the Contract for project warranty provisions.
B.
Manufacturer’s Warranty: Submit, for Owner’s acceptance, manufacturer’s standard warranty document executed by
authorized company official. Manufacturer’s warranty is in addition to, and not a limitation of, other rights Owner may have
under contract documents.
C.
Warranty Period: BonaKemi stands behind its products; however, many variables can and do occur at the site of
application. A successful installation is dependent on application technique and proper environmental conditions; therefore,
installation is not warranted. For additional information on warranty conditions, duration and remedies, contact BonaKemi
USA Inc.
PART 2 PRODUCTS
Specifier Note: Retain article below for proprietary method specification. Add product attributes, performance characteristics, material
standards, and descriptions as applicable. Use of such phrases as “or equal” or “or approved equal” or similar phrases may cause
ambiguity in specifications. Such phrases require verification (procedural, legal and regulatory) and assignment of responsibility for
determining “or equal” products.
2.01 SPORT FLOOR FINISHING SYSTEM
Specifier Note: Paragraph below is an addition to CSI SectionFormat and a supplement to MANU-SPEC. Retain or delete paragraph
below per project requirements and specifier’s practice.
A.
Manufacturer: BonaKemi USA Inc.
1.
Contact: 14805 E. Moncrieff Place, Aurora, CO 80011; Telephone: (800) 872-5515, (303) 371-1411;
Fax: (303) 371-6958; E-mail: gerry.mueller@bona.com; Web site: www.bonakemi.com.
Specifier Note: BonaKemi USA Inc. manufactures sport floor finishing systems. Edit, retain or delete subparagraphs below to suit
project requirements and specifier practice.
B.
Proprietary Products/Systems. Sport floor systems, including the following:
SPEC-DATA® and MANU-SPEC® are registered trademarks of Reed Elsevier Inc. The three part MANU-SPEC format conforms to the editorial style of the Construction
Specifications Institute and is used with their permission. The manufacturer is responsible for technical accuracy. ©2004 Reed Construction Data. All Rights Reserved.
FLOOR TREATMENT
09610
BonaKemi USA Inc.
Specifier Note: SuperSport Seal’s quick-drying, non-ambering, waterborne formula reduces grain raise and prepares the floor for a
protective top coat of SuperSport finish. SuperSport Seal seals the wood, provides a high-build layer with elasticity, and prevents the
finish from penetrating the wood surface. SuperSport Seal Floor Sealer is inherently low in volatile organic compounds (VOCs) and
emits no toxic fumes. There is no need to vacate the area during application. This product is intended for newly sanded floors only.
1.
SuperSport Seal Floor Sealer:
a.
Ingredients: Water, acrylic resin, Dipropylene Glycol Monomethyl Ether, defoamers.
b.
Color: Milky, off-white when wet, clear when dry.
c.
Solids: 35%.
d.
Flash Point: >200 degrees F (93 degrees C).
e.
Viscosity: #4 Ford cup 77 degrees F (25 degrees C), approximately 12 seconds.
f.
Stability: 1 year shelf life in unopened container.
g.
Density: 8.66 lb/gal (1.04 specific gravity).
h.
VOC: Does not exceed 2.1 lb/gal (250 g/L).
i.
Coverage: 450 - 550 ft /gal (11.3 - 13.8 m /L).
j.
Maximum Cure: 100% in 1 week.
k.
Drying Time: 2 - 3 hours.
2
2
Specifier Note: SuperSport is a premium, 2-component waterborne wood floor finish specifically formulated for professional use on
maple sports floors, providing a tough, high-build urethane finish. SuperSport Floor Finish is inherently low in volatile organic
compounds (VOCs) and emits no toxic fumes. There is no need to vacate the area during application.
2.
SuperSport Floor Finish:
a.
Ingredients: Water, polyurethane resin, N-Methyl-2-Pyrrolidone, Dipropylene Glycol Monomethyl Ether and
Dipropylene Glycol N-Butyl Ether.
b.
Color: Milky, off-white when wet, clear when dry.
c.
Gloss Level: (60 degrees) 88+.
d.
pH: 8.3.
e.
Solids: 28%.
f.
Flash Point: >200 degrees F (93 degrees C).
g.
Viscosity: #4 Ford cup 77 degrees F (25 degrees C), approximately 16 seconds.
h.
Stability: 1 year shelf life in unopened container.
i.
Density: 8.52 lb/gal (1.02 specific gravity).
j.
VOC: Does not exceed 2.9 lb/gal (350 g/L).
k.
Coverage: 500 - 600 ft /gal (12.5 - 15 m /L).
l.
Percent Cured After 24 Hours: 80%.
m.
Maximum Cure: 100% in 1 week.
n.
Drying Time: 2 - 3 hours.
2
2
Specifier Note: Sport Seal oil modified sealer is for sport and all-purpose floors. For use over newly sanded sports floors. Sport Seal
meets the federal, and most state, clean air quality standards. Formulated for use with Bona Sport Sport Poly oil modified polyurethane
sports floor finish. Seals the wood, providing a build layer and preventing the finish from penetrating. Does not require thinning under
normal environmental and application conditions.
3.
Sport Seal Floor Sealer:
a.
Ingredients: Oil modified polyurethane resin, mineral spirits (solvent), driers, defoamers.
b.
Color: Light amber, clear when dry.
SPEC-DATA® and MANU-SPEC® are registered trademarks of Reed Elsevier Inc. The three part MANU-SPEC format conforms to the editorial style of the Construction
Specifications Institute and is used with their permission. The manufacturer is responsible for technical accuracy. ©2004 Reed Construction Data. All Rights Reserved.
FLOOR TREATMENT
09610
BonaKemi USA Inc.
c.
Solids: 43%.
d.
Flash Point: 110 degrees F (43 degrees C) (PMCC).
e.
Stability: 1 year shelf life in unopened container.
f.
VOC: Does not exceed 4.2 lb/gal (500 g/L).
g.
Density: 7.3 lb/gal (0.88 specific gravity).
h.
Viscosity: #4 Ford cup 77 degrees F (25 degrees C), approximately 14.5 - 16 seconds.
i.
Coverage: 400 - 500 ft /gal (10 - 12.5 m /L).
j.
Maximum Cure: 2 weeks.
k.
Drying Time: 8 - 12 hours.
2
2
Specifier Note: Sport Poly is a premium quality, oil modified polyurethane developed specifically for the wood sport floor market. Sport
Poly provides an extremely tough, high-build gloss finish with excellent chemical resistance, protecting against perspiration and routine
cleaning. Bona Sport Sport Poly meets federal, and most state, clean air quality standards.
4.
Sport Poly Floor Finish:
a.
Ingredients: Oil modified polyurethane resin, mineral spirits (solvent), driers, defoamers.
b.
Color: Light amber, clear when dry.
c.
Solids: 50%.
d.
Flash Point: 110 degrees F (43 degrees C) (PMCC).
e.
Stability: 1 year shelf life in unopened container.
f.
VOC: Does not exceed 3.8 lb/gal (450 g/L).
g.
Density: 7.3 lb/gal (0.88 specific gravity).
h.
Viscosity: #4 Ford cup 77 degrees F (25 degrees C), approximately 21 - 24 seconds.
i.
Coverage: 500 ft /gal (12.5 m /L).
j.
Percent Cured After 24 Hours: 50%.
k.
Maximum Cure: 2 weeks.
l.
Drying Time: 8 - 12 hours.
2
2
Specifier Note: CourtLines is a high-solids, fast-drying, solvent based sport floor paint, manufactured specifically for use with both
waterborne and oil modified sport floor sealers and finishes. Available in 15 vibrant primary colors. Paints are all mixable and tintable to
achieve any custom color desired.
5.
CourtLines Sport Floor Paint:
a.
Ingredients: Alkyd resins, odorless mineral spirits, pigments, driers, titanium dioxide (white only).
b.
Base Color: [Red] [Yellow] [Green] [Blue] [Dark blue] [Orange] [Brown] [Black] [White] [Gold] [Maroon] [Purple]
[N.C. Blue] [Gray] [Light Beige].
c.
Solids: Colors 47 - 51%, White 66%.
d.
Flash Point: 100 degrees F (38 degrees C) (TCC).
e.
Viscosity: 60 - 70 KU (Stormer at 77 degrees F (25 degrees C)).
f.
Density: Colors 7.6 - 7.9 lb/gal, White 11.1 lb/gal.
g.
VOC: Does not exceed 3.75 lb/gal (450 g/L).
h.
Stability: At least 1 year shelf life in unopened container.
i.
Coverage: 325 - 500 ft /gal (8.1 - 12.5 m /L).
j.
Drying Time: 24 hour recoat.
2
2
Specifier Note: Edit Article below to suit project requirements. If substitutions are permitted, edit text below. Add text to refer to
SPEC-DATA® and MANU-SPEC® are registered trademarks of Reed Elsevier Inc. The three part MANU-SPEC format conforms to the editorial style of the Construction
Specifications Institute and is used with their permission. The manufacturer is responsible for technical accuracy. ©2004 Reed Construction Data. All Rights Reserved.
FLOOR TREATMENT
09610
BonaKemi USA Inc.
Division 1 Project Requirements (Product Substitutions Procedures) Section.
2.02 PRODUCT SUBSTITUTIONS
A.
Substitutions: No substitutions permitted.
PART 3 EXECUTION
Specifier Note: Article below is an addition to the CSI SectionFormat and a supplement to MANU-SPEC. Revise article below to suit
project requirements and specifier’s practice.
3.01 MANUFACTURER’S INSTRUCTIONS
A.
Comply with the instructions and recommendations of the sport floor finish system manufacturer.
B.
For new installation of sport floors, use only in structures with humidity and temperature controls. Do not use over channel
and clip floor systems in environments not controlled for temperature and humidity.
3.02 PREPARATION
A.
Protection: Protect adjacent finish surface to prevent damage during sanding and sport floor system application.
B.
Surface Preparation:
1.
Sand and prepare floor using MFMA accepted methods.
2.
For Sport Poly oil modified system, make final sanding cut to 100 - 120 grit paper. Screen with 100 - 120 grit screen.
3.
For SuperSport waterborne system, make final cut with 100 - 120 grit sandpaper and screen to 120 - 150 grit.
4.
Vacuum thoroughly.
5.
For Sport Poly, tack with mineral spirits.
6.
For SuperSport, tack with slightly water dampened Bona Mop or cloth.
3.03 APPLICATION
A.
Specific application methods vary with product. Consult manufacturer and comply fully with manufacturer’s application
recommendations.
1.
Before using these products, read and understand all directions and the Material Safety Data Sheets (MSDS).
2.
Shake well before using.
3.
Do not thin these products.
4.
Keep from freezing.
Specifier Note: Coordinate article below with Division 1 Execution Requirements Section.
3.04 PROTECTION
A.
After application, protect sport floor finish from damage during subsequent work.
B.
Do not allow foot traffic until floor is sufficiently dried and cured.
END OF SECTION
SPEC-DATA® and MANU-SPEC® are registered trademarks of Reed Elsevier Inc. The three part MANU-SPEC format conforms to the editorial style of the Construction
Specifications Institute and is used with their permission. The manufacturer is responsible for technical accuracy. ©2004 Reed Construction Data. All Rights Reserved.