Product Overview
XV054C150V054RNT1
Brand Name
Description
Input Voltage
Input Freq.
RoHS
Status
Input
Voltage
(Vac)
Output
Power
(W)
Output
Voltage
Range
(V)
Output
Current
(A)
Efficiency@ Max
Load and 70°C Amb
Max Case
Temp.
(°C)
Input
Current
(Arms)
Max.
Input
Power
(W)
277
54
27 - 54
0.7 – 1.5
84
85 °C
0.28
68
XITANIUM
XITANIUM 54W 0.7-1.5A 54V Mrk10 Dim
277 V
60Hz
Yes
Released
THD @ Power
Surge
Inrush
Max Factor @ Protection
Current
Load
Max
Common/
(Apk/50%-µs)
(%)
Load
Diff (KV)
12/ 274
<15%
>0.95
2/2
Weight
(Lbs/kgs)
Envir.
Protection
Rating
0.734/
0.333
UL damp
and dry
Note: All the above presented data is without dimmer
Wiring Diagram
GROUND
N/C
LINE 2
NEUTRAL
LED+
LED+
LED‐
LED‐
NTC
RSET2
DRIVER
SGND
Dimming
Dimming
Range
Minimum Output
Current (A)
Mark10 dimming
5% ~100%
0.035
Enclosure
Input and output are WAGO 250 connectors.
Connect wires:
Use 18 AWG Solid Copper Wire Rated>=300V.
Strip Wire 3/8”.
Case Length
Case Width
Case Height
in. (mm)
14.17 (360)
1.18 (30)
1.0 (25.4)
Revised 02/20/2014
PHILIPS LIGHTING ELECTRONICS N.A.
10275 WEST HIGGINS ROAD · ROSEMONT, IL 60018
Tel: 800-322-2086 · Fax: 888-423-1882 · www.philips.com/advance
Customer Support/Technical Service: 800-372-3331 · OEM Support: 866-915-5886
Other
Comments
Electrical Specifications
All the specifications are typical and at 25°C Tcase unless
specified otherwise.
Order code
XV054C150V054RNT1
Full product code
XV054C150V054RNT1M
XV054C150V054RNT1
Brand Name
Description
Input Voltage
Input Freq.
RoHS
Status
Full product name
XITANIUM 54W 0.7-1.5A 54V Mrk10 Dim
Line Voltage
277Vac rms
Line Current
0.28A @ 277V
Line Frequency
60Hz
Min. Mains voltage operational
249 V [min]
Max. Mains voltage operational
305V [max]
THD (total)
Refer to graph
Power Factor (PF)
Refer to graph
Inrush Current
Per NEMA 410
XITANIUM
XITANIUM 54W 0.7-1.5A 54V Mrk10 Dim
277 V
60Hz
Yes
Released
Input Over-voltage
Can survive input over-voltage stress of 320VAC for 48 hours
Lightning Surge Protection
Per ANSI C62.41 Category A (2KV Combination Wave and 6KV ring wave)
Output voltage range
27V to 54Vdc
Maximum open circuit voltage
57V
Output Current Ripple
20% max @ 1.5A
(ripple = peak to peak / average)
Low frequency (≤120 Hz) content <5%
Protections
Short Circuit and Open Circuit Protection for LED + and LED-
Ambient Temp Range
-20C to +50C (corresponding Tcase +5C to +75C)
Max Case Temperature (Tcase)
85C
Encapsulation
Partial potting
Interfaces
Mark10 Dimming, AOC, MTP
AOC (Adjustable Output Current)
100mA to 1500mA via external resistor (refer to graph below & notes in the Application section)
MTP (Module Temperature Protection)
refer to graph below
Mar10 Dimming Specifications
5% of Iout_set
Environmental Protection Rating
UL damp and dry
Life @ Tcase 75C
50000 hr [nom] refer to graph below
Life @ Tcase 85C
25000 hr [nom] refer to graph below
Agency Approbations
UL8750, UL1310, UL935, CSA-C22.2 No. 250.13-12, CSA C22.2 No. 223
Electromagnetic Compliance
FCC Title 47 Part 15 Class A
Isolation
Refer to table
Revised 02/20/2014
PHILIPS LIGHTING ELECTRONICS N.A.
10275 WEST HIGGINS ROAD · ROSEMONT, IL 60018
Tel: 800-322-2086 · Fax: 888-423-1882 · www.philips.com/advance
Customer Support/Technical Service: 800-372-3331 · OEM Support: 866-915-5886
Electrical Specifications
All the specifications are typical and at 25°C Tcase unless
specified otherwise.
XV054C150V054RNT1
Brand Name
Description
Input Voltage
Input Freq.
RoHS
Status
XITANIUM
XITANIUM 54W 0.7-1.5A 54V Mrk10 Dim
277 V
60Hz
Yes
Released
Mark10 Dimming:
LED Current Tolerance is 5% of Imax over temperature and component variations.
Minimum Dim Level: 5% of Iout_set (minimum 35mA)
Vrms & Output Current
1.6
1.4
Output Current (A)
1.2
1
0.8
0.6
0.4
0.2
0
60.0
80.0
100.0 120.0 140.0 160.0 180.0 200.0 220.0 240.0 260.0 280.0 300.0
Vrms
Conduction Vrms (V) angle(degree) 163 149 140 128 115 101 85 72 61 50 45 276.2 272.6 267.8 257.7 241.6 218.2 184.7 153.3 125.1 96.4 83.5 output current (A) 1.5 1.5 1.5 1.344 1.11 0.836 0.47 0.16 0.075 0.075 0.075 Revised 02/20/2014
PHILIPS LIGHTING ELECTRONICS N.A.
10275 WEST HIGGINS ROAD · ROSEMONT, IL 60018
Tel: 800-322-2086 · Fax: 888-423-1882 · www.philips.com/advance
Customer Support/Technical Service: 800-372-3331 · OEM Support: 866-915-5886
Electrical Specifications
All the specifications are typical and at 25°C Tcase unless
specified otherwise.
XV054C150V054RNT1
Brand Name
Description
Input Voltage
Input Freq.
RoHS
Status
XITANIUM
XITANIUM 54W 0.7-1.5A 54V Mrk10 Dim
277 V
60Hz
Yes
Released
Approved Dimmer List:
Dimmer Brand
manufacturer
Intellisight
Mark 10, Occupancy sensor Neutal Wattage /VA
wire
Yes
1000VA
Occuswitch Wireless LRD1730
Mark 10 wireless dimmer
Yes
800W/1600W
120/277V
2 @ 277V
Sunrise/Momentum ZP1000EB
Mark 10
Yes
1000VA
120V
1
1
Philips Mark Onset
10 Dimmer
VEGA
Multiset Pro
Multiset Pro
Philips Phase Occuswitch Classic
Cut Dimming Occuswitch Classic
Applifier
Model
Dimmer type
ITSEBU
Input voltage 120/277V
Min. no. of drivers/dimmer
2 @ 277V
OS600EB
Mark 10
Yes
600VA
120V
V1500EBU
Mark 10
Yes
1500W
120/277V
2 @ 277V
MSP600EB
Mark 10
Yes
600VA
120V
1
MHP1000EB
Mark 10
Yes
1000W
120V
1
LCU2425
Mark 10 power extender
Yes
1920W
120V
1
277V
2
LCU2430
Mark 10 power extender
Yes
3000W
Renoir II
AWSMT‐XAW
Mark 10
Yes
600/1150/1385W 120/230/277 V 2@120V / 3@277V
Renoir II
AWSMT‐XBW
Mark 10
Yes
1000/1917/2308W 120/230/277 V 2@120V / 3@277V
Renoir II
AWSMT‐XCW
Mark 10
Yes
1500/2875/3463W 120/230/277 V 2@120V / 3@277V
Renoir II
AWSMT‐XDW
Mark 10
Yes
1920/3680/4432W 120/230/277 V 2@120V / 3@277V
Vizia+
VPX10‐1LZ
Mark 10
Yes
1000VA
120V
Vizia+
VPX12‐7LZ
Mark 10
Yes
1200VA
277V
2 @ 277V
Illumatech
IPX06‐10Z
Mark 10
No
600VA
120V
1
IPX06‐70Z
Mark 10
No
600VA
277V
2 @ 277V
IPX10‐10Z
Mark 10
No
1000VA
120V
1
Illumatech
IPX12‐70Z
Mark 10
No
1200VA
277V
2 @ 277V
Sureslide
6674
LED/CFL/Incandescent
No
150/150/600W
120V
1
Renoir
2666‐31
Mark 10
No
900W/1200VA
120V
2
Renoir
2666‐37
No
900W/1200VA
277V
2 @ 277V
D4200
D4206
Yes
6x1000W
120V
1 per dimmer
WD170
Mark 10
station, 6dimmers, Mark 10, Incandescent
Mark 10, Occupancy sensing
No
500W
120V
1
WD180
Mark 10, Occupancy sensing
No
500W
277V
2
ADFM‐8A
Mark 10
No
120V
1
ADFM277‐10A Mark 10
No
277V
2 @ 277V
Leviton Phase Cut Dimmer Illumatech
Illumatech
Wattstopper Mark 10 Dimmer
Miro
2
DCD267
Universal Mark 10 incandescent Yes
500W
120V
1
Miro wireless
DRD4
universal Mark 10 incandescent Yes
500W
120V
1
DLM
LMRC‐222
Universal Mark 10 incandescent Yes
2x1920W/4432W 120/277V
Nova
NFTU‐5A
Mark 10 (Tu‐wire)
No
120V
1
SPSFTU‐5A
Mark 10 (Tu‐wire)
Yes
120V
1
DVFTU‐5A3P
Mark 10 (Tu‐wire)
No
120V
1
QSGRJ‐X P
Mark 10 (Tu‐wire) Yes
Dimming Amplifier
HP‐2
Mark 10
Nova T
NTFTU‐5A‐277 Mark 10 (Tu‐wire)
Spacer System
Lutron Mark 10 Diva
Dimmer
Grafik Eye QS
††
‡‡
800W/1200W
2
120V
1
Yes
120V/277V
1@120V / 2@277V
Yes
277V
2
Revised 02/20/2014
PHILIPS LIGHTING ELECTRONICS N.A.
10275 WEST HIGGINS ROAD · ROSEMONT, IL 60018
Tel: 800-322-2086 · Fax: 888-423-1882 · www.philips.com/advance
Customer Support/Technical Service: 800-372-3331 · OEM Support: 866-915-5886
Electrical Specifications
All the specifications are typical and at 25°C Tcase unless
specified otherwise.
XV054C150V054RNT1
Brand Name
Description
Input Voltage
Input Freq.
RoHS
Status
XITANIUM
XITANIUM 54W 0.7-1.5A 54V Mrk10 Dim
277 V
60Hz
Yes
Released
AOC (Adjustable Output Current) Settings:
LED current tolerance with variation of Rset2 is within ± 5% of Imax
Rset (Ohms) 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 >8200 Current (mA) 98.2 110.2 1293.2 142.4 156.8 177.6 214.9 236.5 266.2 298 353.4 396.3 456.9 515.1 607.5 687.6 780.3 888.8 986.9 1084.6 1186.1 1283.2 1408.3 1498.2 1498.2 Notes:
 Any through hole or SMD resistor with >0.25W and >20V can be used as RSET2 between Rset2 and
SGND pins
 The driver will default to 1500mA when Rset is left open
 For loads above 36V, a proper Rset value should be selected to keep the output power at or below 54W
Revised 02/20/2014
PHILIPS LIGHTING ELECTRONICS N.A.
10275 WEST HIGGINS ROAD · ROSEMONT, IL 60018
Tel: 800-322-2086 · Fax: 888-423-1882 · www.philips.com/advance
Customer Support/Technical Service: 800-372-3331 · OEM Support: 866-915-5886
Electrical Specifications
XV054C150V054RNT1
All the specifications are typical and at 25°C Tcase unless
specified otherwise.
Brand Name
Description
Input Voltage
Input Freq.
RoHS
Status
XITANIUM
XITANIUM 54W 0.7-1.5A 54V Mrk10 Dim
277 V
60Hz
Yes
Released
Operating Window:
Operating Window for XV054C150V054RNT1
55
Output Voltage(Vdc)
50
45
40
Min. current by Rset Min. current by Rset when using LE dimming 35
30
25
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.1
1.2
1.3
Nominal Output Current (mAdc)
Revised 02/20/2014
PHILIPS LIGHTING ELECTRONICS N.A.
10275 WEST HIGGINS ROAD · ROSEMONT, IL 60018
Tel: 800-322-2086 · Fax: 888-423-1882 · www.philips.com/advance
Customer Support/Technical Service: 800-372-3331 · OEM Support: 866-915-5886
1.4
1.5
1.6
Electrical Specifications
XV054C150V054RNT1
All the specifications are typical and at 25°C Tcase unless
specified otherwise.
Brand Name
Description
Input Voltage
Input Freq.
RoHS
Status
XITANIUM
XITANIUM 54W 0.7-1.5A 54V Mrk10 Dim
277 V
60Hz
Yes
Released
Module Temperature Protection:
Iout % vs External NTC Resistance
120%
2966, 100%
Iout % (A)
100%
80%
60%
40%
20%
2176, 0%
0%
1000
1200
1400
1600
1800
2000 2200 2400 2600
External NTC (ohm)
2800
3000
3200
3400
For example: Using NTC Vishay 15kOhm ± 2% NTC, B25/85=3700 (2381 615 54153), the output current Vs
module temperature behavior is as follows.
Iout(%) vs LED Module Temperature using 15k NTC
120%
100%
Iout(%)
80%
60%
40%
20%
0%
0
10
20
30
40
50
60
70
80
90
Module Temperature (°C)
Revised 02/20/2014
PHILIPS LIGHTING ELECTRONICS N.A.
10275 WEST HIGGINS ROAD · ROSEMONT, IL 60018
Tel: 800-322-2086 · Fax: 888-423-1882 · www.philips.com/advance
Customer Support/Technical Service: 800-372-3331 · OEM Support: 866-915-5886
100
110
Electrical Specifications
All the specifications are typical and at 25°C Tcase unless
specified otherwise.
XV054C150V054RNT1
Brand Name
Description
Input Voltage
Input Freq.
RoHS
Status
XITANIUM
XITANIUM 54W 0.7-1.5A 54V Mrk10 Dim
277 V
60Hz
Yes
Released
Iout vs. Tcase of Driver:
Iout % vs Tcase of the Driver
120%
Iout % (A)
100%
80%
60%
40%
20%
0%
45
55
65
75
Tcase (°C)
85
95
105
115
Lifetime vs. Tcase of Driver:
Lifetime vs Tcase
60
Life (kHours)
55
50
45
40
35
30
25
20
30
35
40
45
50
55
60
65
Tcase (deg.C)
70
75
80
Revised 02/20/2014
PHILIPS LIGHTING ELECTRONICS N.A.
10275 WEST HIGGINS ROAD · ROSEMONT, IL 60018
Tel: 800-322-2086 · Fax: 888-423-1882 · www.philips.com/advance
Customer Support/Technical Service: 800-372-3331 · OEM Support: 866-915-5886
85
90
Electrical Specifications
All the specifications are typical and at 25°C Tcase unless
specified otherwise.
XV054C150V054RNT1
Brand Name
Description
Input Voltage
Input Freq.
RoHS
Status
XITANIUM
XITANIUM 54W 0.7-1.5A 54V Mrk10 Dim
277 V
60Hz
Yes
Released
Failure Rate based upon field call rate data:  <0.01% per 1k Hrs @ ≤ Tcase 75°C Inrush Current Info:
Vin 277 Vrms Ipeak 11.6A T (@ 50% of Ipeak) 274 µs Inrush current is measured at peak of the corresponding line voltage, source impedance per NEMA 410. Revised 02/20/2014
PHILIPS LIGHTING ELECTRONICS N.A.
10275 WEST HIGGINS ROAD · ROSEMONT, IL 60018
Tel: 800-322-2086 · Fax: 888-423-1882 · www.philips.com/advance
Customer Support/Technical Service: 800-372-3331 · OEM Support: 866-915-5886
Performance Characteristics
XV054C150V054RNT1
Based on measurements on a typical sample. The accuracy
of the measurements is within the tolerance of the
measurement instruments. The graphs are meant to be a
guideline and not a specification.
Brand Name
Description
Input Voltage
Input Freq.
RoHS
Status
XITANIUM
XITANIUM 54W 0.7-1.5A 54V Mrk10 Dim
277 V
60Hz
Yes
Released
Efficiency vs Output Voltage @1.5A
88.0%
Efficiency
87.0%
86.0%
85.0%
84.0%
83.0%
82.0%
27
28
29
30
31
32
33
34
35
36
48
51
54
Vout(V)
Efficiency vs. Output Votlage @1.0A
84.0%
83.5%
Efficiency 83.0%
82.5%
82.0%
81.5%
81.0%
80.5%
80.0%
27
30
33
36
39
42
45
Vout (V)
Revised 02/20/2014
PHILIPS LIGHTING ELECTRONICS N.A.
10275 WEST HIGGINS ROAD · ROSEMONT, IL 60018
Tel: 800-322-2086 · Fax: 888-423-1882 · www.philips.com/advance
Customer Support/Technical Service: 800-372-3331 · OEM Support: 866-915-5886
Performance Characteristics
XV054C150V054RNT1
Based on measurements on a typical sample. The accuracy
of the measurements is within the tolerance of the
measurement instruments. The graphs are meant to be a
guideline and not a specification.
Brand Name
Description
Input Voltage
Input Freq.
RoHS
Status
XITANIUM
XITANIUM 54W 0.7-1.5A 54V Mrk10 Dim
277 V
60Hz
Yes
Released
Power Factor vs Output Power
1
Power Factor
0.99
0.98
0.97
277V input
0.96
0.95
27
30
33
36
39
42
45
48
51
54
Pout(W)
THD vs Output Power
THD (%)
14
12
10
8
6
277v input
4
2
0
27
32
37
42
47
52
Pout(W)
Revised 02/20/2014
PHILIPS LIGHTING ELECTRONICS N.A.
10275 WEST HIGGINS ROAD · ROSEMONT, IL 60018
Tel: 800-322-2086 · Fax: 888-423-1882 · www.philips.com/advance
Customer Support/Technical Service: 800-372-3331 · OEM Support: 866-915-5886
Application Notes:
XV054C150V054RNT1
Brand Name
Description
Input Voltage
Input Freq.
RoHS
Status
XITANIUM
XITANIUM 54W 0.7-1.5A 54V Mrk10 Dim
277V
60Hz
Yes
Released
Installation & Application Notes:
1.
2.
3.
4.
5.
6.
LED Driver shall be installed inside an electrical enclosure.
Wiring inside electrical enclosure shall comply with 300V/105°C rating or higher.
Max number of LEDs in series should not exceed 16.
Max LED voltage should not exceed 54V under all operating conditions.
Rset can be used to adjust output current between 700 to 1500 mA for Mark10 dimming operation.
Rset can be used to adjust output current between 100 to 1500 mA for fixed output operation.
Isolation:
Input connectors Output + AOC & External NTC Connectors Enclosure Not applicable 2xU+1KV 2xU+1KV Output + AOC & External NTC Connectors 2xU+1KV Not applicable >500V Enclosure 2xU+1KV
>500V
Not applicable Isolation Input connectors UL Conditions of Acceptability:
Please contact your Philips representative for a copy of the latest UL Conditions Of Acceptability (COA).
Revised 02/20/2014
PHILIPS LIGHTING ELECTRONICS N.A.
10275 WEST HIGGINS ROAD · ROSEMONT, IL 60018
Tel: 800-322-2086 · Fax: 888-423-1882 · www.philips.com/advance
Customer Support/Technical Service: 800-372-3331 · OEM Support: 866-915-5886