Passive Panel Replacement
for E-Series Hinged Inswing and Outswing Patio Doors with Type III Hardware
Thank you for choosing Andersen.
For questions call 1-888-888-7020. For more information and/or guides visit www.eaglewindow.com.
Please leave this guide with building owner.
▶▶ Read guide from beginning to end before starting installation. Read all warnings and cautions during unit installation.
▶▶ Check with your local building code official to identify and confirm compliance with local building code requirements.
Parts Included (1) Passive Panel
Tools Needed Herramientas necesarias
∙∙ Safety Glasses Lentes de seguridad
∙∙ Drill/Driver
∙∙ #2 Phillips Bit
∙∙ 2.5 mm Hex Key
∙∙ #2 Phillips Screwdriver P
∙∙ Caulk Gun
s Screwdriver
Supplies Needed
∙∙ Sealantentes de seguridad
Passive Panel
Windows and doors can be heavy. Use safe lifting techniques and a reasonable number
of people with enough strength to lift, carry and install window and door products to avoid
injury and/or product damage.
Las puertas y las ventanas pueden ser pesadas. Utilice técnicas seguras de levantamiento
de peso y un número razonable de personas con suficiente fuerza para levantar, cargar e
instalar los productos de puertas y ventanas, a fin de evitar lesiones y/o daños al producto.
Panel must be supported during entire removal and
installation procedures. Failure to support sash may result in
injury and/or product damage.
Use caution when working at elevated heights and around unit openings. Follow
manufacturers’ instructions for ladders and/or scaffolding. Failure to do so may
result in injury or death.
Sea cauteloso al trabajar en lugares elevados y cerca de las aberturas de la unidad.
Siga las instrucciones del fabricante para el uso de escaleras y/o andamios. Si no lo
hiciera, podrían producirse lesiones o la muerte.
Follow manufacturers’ instructions for hand or power tools.
Always wear safety glasses. Failure to do so may result in injury
and/or product damage.
Siga las instrucciones del fabricante para el uso de herramientas
eléctricas o manuales. Utilice siempre gafas de seguridad. Si no
lo hiciera, podrían producirse lesiones y/o daños al producto.
La hoja debe sostenerse durante todo el proceso de
extracción e instalación. De no sostenerla, podrían
producirse lesiones y/o daños al producto.
“Andersen” and all other marks where denoted are trademarks of Andersen Corporation and its subsidiary. ©2013 Andersen Corporation. All rights reserved.
9 0 6 9 2 5 2 BA
Revised 10/16/13
2
1
Passive Panel
Exterior
Thumb
Turn
Passive
Door
Panel
Active
Door
Panel
Interior Views
Open active door panel.
Exterior View
Open passive door by rotating thumb turn to unlock hardware. Then push down on handle to open
passive panel.
3
4
Interior
Interior
Drill/
Driver
2.5mm Hex Key
Handle
Escutcheon
Plate Screws
Escutcheon
Plate Screws
Loosen handle set screw with a 2.5 mm hex key.
Remove two (2) escutcheon plate screws with a drill/driver and save
for reuse.
5
Interior Escutcheon Plate
Exterior Escutcheon Plate
Remove interior and exterior handle/escutcheon plates and save for reuse.
9069252
2
6
Exterior
Drill/Driver
Center Strike Plate
Drill/Driver
Top and Bottom Strike Plates
Remove screws attaching top, center and bottom strike plates. Save screws for reuse.
7
Center Strike Plate
Dust Cap
Exterior
Top and Bottom Strike
Plate Dust Caps
Center Strike Plate
Top and Bottom
Strike Plates
Remove center strike plate and dust cup and save for reuse. Remove top and bottom strike plates and dust cups and save for reuse.
8
Exterior
Weight of window/door
unit(s) and accessories
will vary. Use a
reasonable number of
people with sufficient
strength to lift, carry, and
install window and door
unit(s) and accessories.
Always use appropriate
lifting techniques.
Active
Door
Panel
Passive
Door
Panel
Support passive panel before removing panel hinge screws.
9069252
3
9
Interior
10
Passive
Panel
Hinge Cup
#12 x 1 1/2"
Screws
Hinge Shims
Note position
and quantity.
Drill/
Driver
Note position and quantity of shims in hinge routes. Remove hinge
cups and shims from each hinge route and save for reuse.
Remove four (4) #12 x 1 1/2" screws from each hinge on panel and
save for reuse. Place panel upright against a stable surface.
11
12
Hinge Cup
Interior
Hinge Shims
Note position
and quantity.
Passive
Panel
#12 x 1 1/2"
Screws
If replacing an
outswing panel
apply a light coat of
silicone to all hinge
routes on panel
before reapplying
hinge cups.
Drill/
Driver
Position hinge cups and shims in hinge routs on new panel at locations
noted in previous step. Hold shims in place with a dab of sealant.
13
Support door panel at all times while attaching panel to hinges on frame
using screws saved from previous step.
Center Strike Plate
Dust Cap
Exterior
Top and Bottom Strike
Plate Dust Caps
Center Strike Plate
Top and Bottom
Strike Plates
Reapply saved center strike plate and dust cup. Reapply saved top and bottom dust cups and strike plates. Secure with saved screws.
9069252
4
14
15
Door
Panel
Plate
Exterior
Interior
Exterior
Escutcheon
Plate/
Gasket
Handle
Spindle
Interior
Escutcheon
Plate
Interior
Escutcheon
Plate
Align handle spindle with slot in lock mechanism and position exterior
escutcheon plate/gasket assembly against door panel.
Place interior escutcheon assembly against door panel with tail piece
on thumb turn aligned with slot in lock mechanism. Check for proper
operation of thumb turn.
16
17
Interior
Interior
2.5mm Hex Key
Drill/Driver
Handle
Fasten interior escutcheon plate using saved screws.
Tighten handle set screw with a 2.5 mm hex key.
Remove two (2) escutcheon plate screws and dispose of properly.
18
19
Thumb
Turn
Handle
Exterior View
Exterior
Interior
Views
Close passive door panel. Lock door panel by first lifting up on handle, then turning thumb turn
counterclockwise.
Close and lock active door panel. Check for
correct lock operation.
▶▶ Passive panel replacement is completed.
9069252
5