FT-991 - Yaesu System Fusion Customer Portal

FT-991
CAT Operation
Reference Book
YAESU MUSEN CO., LTD.
CAT (Computer Aided Transceiver) Operation
Overview
Connection
The CAT (Computer Aided Transceiver) System in
the FT-991 transceiver provides control of frequency,
VFO, memory, and other settings such as dualchannel memories and diversity reception using an
external personal computer. This allows multiple
control operations to be fully automated with single
mouse clicks, or keystroke operations on the computer
keyboard.
⑨ ⑧ ⑦ ⑥
⑤④ ③ ②①
Using the RS-232C Cable (Refer to figure 1)
The FT-991 transceiver has a built-in level converter,
allowing direct connection from the rear-panel CAT jack
to the serial port of your computer without the need of
any external boxes.
Pin No.
Pin Name
I/O

N/A
---
---
‚
SERIAL OUT
Output
Outputs the Serial Data from
the transceiver to the computer.
ƒ
SERIAL IN
Input
Inputs the Serial Data from the
computer to the transceiver.
„

†
‡
ˆ
‰
When using the RS-232C cable, set Menu item “028
GPS/232C SELECT” to “RS232C”.
You will need a serial cable for connection to the RS232C (serial or COM port) connector on your computer.
Purchase a standard serial cable (not the so-called “null
modem” type), ensuring it has the correct gender and
number of pins (some serial COM port connectors use a
9-pin rather than 25-pin configuration). If your computer
uses a custom connector, you may have to construct the
cable. In this case, refer to the technical documentation
supplied with your computer for correct data connection.
Function
N/A
---
---
GND
---
Signal Ground
N/A
---
---
RTS
---
---
CTS
---
---
N/A
---
---
Personal Computer
Using the USB Cable (Refer to figure 2)
Note:A USB driver is required for remote control from
a computer. Download the driver from the Yaesu
website (http://www.yaesu.com).
FT-991
COM
GPS/CAT
The FT-991 transceiver has a built-in USB to Dual
UART Bridge, allowing direct connection from the
rear-panel USB jack to the USB jack of your computer
without the need of any external boxes.
You will need a USB cable to connect to the USB jack
on your computer.
RS-232C “Straight” Cable
Figure 1
YAESU MUSEN does not produce CAT System
operating software due to the wide variety of personal computers and operating systems in use today.
However, the information provided in this chapter
explains the serial data structure and opcodes used
by the CAT system. This information, along with
the short programming examples, is intended to
help you start writing programs on your own. As
you become more familiar with CAT operation, you
can customize programs for your operating needs
and utilize the full operating potential of this system.
Personal Computer
FT-991
USB
USB
USB Cable
Figure 2
1
FT-991 CAT Operation Manual
CAT (Computer Aided Transceiver) Operation
Control Command
A computer control command is composed of an alphabetical command, various parameters, and the terminator
that signals the end of the control command.
Parameters
Example: Set the VFO-A frequency to 14.250000 MHz.
The parameters to be used for each command are predetermined. The number of digits assigned to each
parameter is also predetermined. Refer to the “Control
Command List” and the “Control Command Tables” to
configure the appropriate parameters.
Parameters are used to specify information necessary to
implement the desired command.
FA
014250000;



Command ParameterTerminator
There are three commands for the FT-991 as shown below:
When configuring parameters, be careful not to make
the following mistakes.
Set command: Set a particular condition
(to the FT-991)
Read command: Reads an answer
(from the FT-991)
Answer command: Transmits a condition
(from the FT-991)
For example,
when the correct parameter is “IS0+1000” (IF SHIFT):
IS01000;
Not enough parameters specified (No direction (+)
given for the IF shift)
IS0+100;
Not enough digits (Only three frequency digits
given)
IS0_+_1000;
Unnecessary characters between parameters
IS0+10000;
Too many digits (Five frequency digits given)
For example, note the following case of the FA command (Set the VFO-A frequency):
 To set the VFO-A frequency to 14.250000 MHz, the
following command is sent from the computer to the
transceiver:
“FA014250000;” (Set command)
 To read the VFO-A frequency, the following command is sent from the computer to the transceiver:
“FA;” (Read command)
 When the Read command above has been sent, the
following command is returned to the computer:
“FA014250000;” (Answer command)
Note: If a particular parameter is not applicable to the
FT-991, the parameter digits should be filled using any
character except the ASCII control codes (00 to 1Fh)
and the terminator (;).
Terminator
Alphabetical Commands
To signal the end of a command, it is necessary to use
a semicolon (;). The digit where this special character
must appear differs depending on the command used.
A command consists of 2 alphabetical characters.
You may use either lower or upper case characters. The
commands available for this transceiver are listed in the
“PC Control Command Tables” on the following pages.
2
FT-991 CAT Operation Manual
CAT (Computer Aided Transceiver) Operation
Command
Function
AB
VFO-A TO VFO-B
ANTENNA TUNER
AC
CONTROL
AG
AF GAIN
AI
AUTO INFORMATION
VFO-A TO MEMORY
AM
CHANNEL
BA
VFO-B TO VFO-A
BC
AUTO NOTCH
BD
BAND DOWN
BI
BREAK-IN
BP
MANUAL NOTCH
BS
BAND SELECT
BU
BAND UP
BY
BUSY
CH
CHANNEL UP/DOWN
CN
CTCSS NUMBER
CO
CONTOUR
CS
CW SPOT
CT
CTCSS
DA
DIMMER
DN
DOWN
DT
DATE AND TIME
ED
ENCORDER DOWN
EK
ENT KEY
EU
ENCORDER UP
EX
MENU
FA
FREQUENCY VFO-A
FB
FREQUENCY VFO-B
FS
FAST STEP
FT
FUNCTION TX
GT
AGC FUNCTION
ID
IDENTIFICATION
IF
INFORMATION
IS
IF-SHIFT
KM
KEYER MEMORY
KP
KEY PITCH
KR
KEYER
KS
KEY SPEED
KY
CW KEYING
LK
LOCK
LM
LOAD MESSEGE
MEMORY CHANNEL TO
MA
VFO-A
MC
MEMORY CHANNEL
MD
MODE
MG
MIC GAIN
ML
MONITOR LEVEL
MR
MEMORY READ
MS
METER SW
MW
MEMORY WRITE
MX
MOX SET
NA
NARROW
NB
NOISE BLANKER
NOISE BLANKER
NL
LEVEL
NR
NOISE REDUCTION
OPPOSITE BAND
OI
NFORMATION
OFFSET (Repeater
OS
Shift)
PA
PRE-AMP (IPO)
PB
PLAY BACK
PC
POWER CONTROL
SPEECH PROCESSOR
PL
LEVEL
Set Read Ans.
O
X
X
AI
X
O
O
O
O
O
O
O
O
O
O
O
X
O
X
X
X
O
O
O
O
O
O
O
X
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
X
X
O
O
O
O
O
O
O
O
X
O
X
O
O
X
X
O
X
O
O
O
O
O
X
O
X
X
X
O
O
O
O
O
O
O
O
O
O
O
O
O
X
O
O
X
O
X
O
O
X
X
O
X
O
O
O
O
O
X
O
X
X
X
O
O
O
O
O
O
O
O
O
O
O
O
O
X
O
O
X
O
X
O
O
X
X
O
X
O
O
O
O
X
X
X
X
X
X
O
O
O
O
O
O
X
O
O
X
O
O
O
X
O
X
O
X
X
X
O
O
O
O
X
O
O
O
O
O
O
O
O
O
O
O
X
O
O
O
O
O
O
O
O
O
X
O
O
O
X
O
O
O
X
O
X
O
O
O
O
O
O
O
O
O
O
O
X
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
X
O
O
O
O
O
Command
PR
PS
QI
QR
QS
RA
RC
RD
RG
RI
RL
RM
RS
RT
RU
SC
SD
SH
SM
SQ
SV
TS
TX
UL
UP
VD
VG
VM
VX
XT
ZI
3
Function
SPEECH PROCESSOR
POWER SWITCH
QMB STORE
QMB RECALL
QUICK SPLIT
RF ATTENUATOR
CLAR CLEAR
CLAR DOWN
RF GAIN
RADIO INFORMATION
NOISE REDUCTION
LEVEL
READ METER
RADIO STATUS
CLAR
CLAR UP
SCAN
SEMI BREAK-IN DELAY
TIME
WIDTH
S METER
SQUELCH LEVEL
SWAP VFO
TXW
TX SET
UNLOCK
UP
VOX DELAY TIME
VOX GAIN
[V/M] KEY FUNCTION
VOX
TX CLAR
ZERO IN
Set Read Ans.
O
O
O
O
O
O
O
X
X
O
X
X
O
X
X
O
O
O
O
X
X
O
X
X
O
O
O
X
O
O
AI
O
X
X
X
X
O
X
X
O
O
O
O
O
O
X
X
O
O
O
O
O
O
X
O
O
O
O
X
O
O
X
O
X
O
O
O
O
O
O
X
O
O
O
O
X
O
O
O
O
O
O
O
O
O
O
X
O
O
O
X
O
O
X
O
O
X
O
O
O
X
O
O
O
X
O
O
X
O
O
X
O
X
O
X
O
O
O
X
O
O
X
O
O
X
FT-991 CAT Operation Manual
CAT (Computer Aided Transceiver) Operation
AB
Set
Read
Answer
AC
Set
Read
Answer
AG
Set
Read
Answer
AI
Set
Read
Answer
AM
Set
Read
Answer
BA
Set
Read
Answer
BC
Set
Read
Answer
BD
Set
Read
Answer
VFO-A TO VFO-B
1
2
3
A
B
;
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
7
8
9
10
ANTENNA TUNER CONTROL
1
2
A
C
3
1
2
3
A
C
;
1
2
A
C
4
5
P1 P2 P3
3
6
;
4
5
6
7
8
9
10
4
5
6
7
8
9
10
7
8
9
10
P1 P2 P3
P1 0: Fixed
P3 0: Tuner “OFF”
P2 0: Fixed
1: Tuner “ON”
2: Tuning Start
;
AF GAIN
1
2
A
G
3
4
1
2
3
4
A
G
P1
;
3
4
1
2
A
G
5
6
P1 P2 P2 P2
;
5
6
7
8
9
10
5
6
7
8
9
10
P1 P2 P2 P2
P1 0: Fixed
P2 000 - 255
;
AUTO INFORMATION
1
2
3
4
A
I
P1
;
5
6
7
8
9
10
4
5
6
7
8
9
10
5
6
7
8
9
10
1
2
3
A
I
;
1
2
3
4
A
I
P1
;
P10: Auto Information “OFF”
1: Auto Information “ON”
This parameter is set to “0” (OFF) automatically when the transceiver is turned “OFF”.
VFO-A TO MEMORY CHANNEL
1
2
3
A
M
;
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
4
5
6
7
8
9
10
VFO-B TO VFO-A
1
2
3
B
A
;
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
AUTO NOTCH
1
2
B
C
3
4
P1 P2
1
2
3
4
B
C
P1
;
3
4
1
2
B
C
P1 P2
;
P10: Fixed
P2 0: Auto Notch “OFF”
1: Auto Notch “ON”
;
BAND DOWN
1
2
3
4
B
D
P1
;
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
P10: Fixed
4
FT-991 CAT Operation Manual
CAT (Computer Aided Transceiver) Operation
BI
Set
Read
Answer
BP
Set
Read
Answer
BS
Set
Read
Answer
BU
Set
Read
Answer
BY
Set
Read
Answer
CH
Set
Read
Answer
CN
Set
Read
Answer
CO
Set
Read
Answer
BREAK-IN
1
2
3
4
B
I
P1
;
5
6
7
8
9
10
4
5
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
1
2
3
B
I
;
1
2
3
4
B
I
P1
;
P10: Break-in “OFF”
1: Break-in “ON”
MANUAL NOTCH
1
2
B
P
1
2
B
P
1
2
B
P
3
4
P1 P2 P3 P3 P3
3
4
P1 P2
3
4
5
;
6
7
8
9
10
6
7
8
9
10
;
5
P1 P2 P3 P3 P3
;
P10: Fixed
P3P2=0
P2 0: Manual NOTCH “ON/OFF” 000: “OFF”
1: Manual NOTCH LEVEL 001: “ON”
P2=1
001 - 320
(NOTCH Frequency : x 10 Hz )
BAND SELECT
1
2
B
S
3
4
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
5
6
7
8
9
10
P1 P1
5
;
P100: 1.8 MHz
01: 3.5 MHz
02: -
03: 7 MHz
04: 10 MHz
05: 14 MHz
06: 18 MHz
07: 21 MHz
08: 24.5 MHz
09: 28 MHz
10: 50 MHz
11: GEN
12: MW
13: 14: AIR
15: 144 MHz
16: 430 MHz
BAND UP
1
2
3
4
B
U
P1
;
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
B
Y
;
4
5
6
7
8
9
10
5
6
7
8
9
10
P10: Fixed
BUSY
1
1
2
B
Y
3
P1 P2
P10: RX BUSY “OFF”
1: RX BUSY “ON”
P2 0: Fixed
;
CHANNEL UP/DOWN
1
2
3
4
C
H
P1
;
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
8
9
10
P10: Memory Channel “UP”
1: Memory Channel “DOWN”
CTCSS TONE FREQUENCY
1
2
C
N
1
2
C
N
1
2
C
N
3
4
5
6
7
P1 P2 P3 P3 P3
3
4
P1 P2
3
4
5
;
6
7
8
9
10
6
7
8
9
10
9
10
;
5
P1 P2 P3 P3 P3
P10: Fixed
P2 0: CTCSS
1: DCS
P3P2=0 000 - 049: Tone Frequency Number (See Table 1)
P2=1000 - 103: DCS Code Number (See Table 2)
;
CONTOUR
1
2
C
O
1
2
C
O
1
2
C
O
3
4
5
6
7
8
P1 P2 P3 P3 P3 P3
3
4
P1 P2
3
4
5
;
6
7
8
9
10
6
7
8
9
10
;
5
P1 P2 P3 P3 P3 P3
;
P10: Fixed
P3 P2=00000: CONTOUR “OFF”
P2 0: CONTOUR “ON/OFF”
0001: CONTOUR “ON”
1: CONTOUR FREQ
P2=1 0010 - 3200
2: APF “ON/OFF”
(CONTOUR Frequency:10 - 3200Hz)
3: APF FREQ
P2=2 0000: APF “OFF”
0001: APF “ON”
P2=3 0000 - 0050 (APF Frequency: -250 - 250 Hz )
5
FT-991 CAT Operation Manual
CAT (Computer Aided Transceiver) Operation
CS
Set
Read
Answer
CT
Set
Read
Answer
CW SPOT
1
2
3
4
C
S
P1
;
1
2
3
C
S
;
Read
Answer
DN
Set
Read
Answer
DT
Set
Read
Answer
7
8
9
10
4
5
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
1
2
3
4
S
P1
;
3
4
P1 0: OFF
1: ON
CTCSS
1
2
C
T
P1 P2
1
2
3
4
C
T
P1
;
3
4
1
2
C
T
;
P1 P2
023
025
026
031
032
036
043
047
051
053
054
065
071
072
073
P10: Fixed
P2 0: CTCSS “OFF”
1: CTCSS ENC/DEC “ON”
2: CTCSS ENC “ON”
3: DCS “ON”
;
67.0 Hz
69.3 Hz
71.9 Hz
74.4 Hz
77.0 Hz
79.7 Hz
82.5 Hz
85.4 Hz
88.5 Hz
000
001
002
003
004
005
006
007
008
009
010
011
012
013
014
Set
6
C
000
001
002
003
004
005
006
007
008
DA
5
009
010
011
012
013
014
015
016
017
91.5 Hz
94.8 Hz
97.4 Hz
100.0 Hz
103.5 Hz
107.2 Hz
110.9 Hz
114.8 Hz
118.8 Hz
015
016
017
018
019
020
021
022
023
024
025
026
027
028
029
074
114
115
116
122
125
131
132
134
143
145
152
155
156
162
Table 1 (CTCSS Tone Chart)
018
019
020
021
022
023
024
025
026
123.0 Hz
127.3 Hz
131.8 Hz
136.5 Hz
141.3 Hz
146.2 Hz
151.4 Hz
156.7 Hz
159.8 Hz
027
028
029
030
031
032
033
034
035
162.2 Hz
165.5 Hz
167.9 Hz
171.3 Hz
173.8 Hz
177.3 Hz
179.9 Hz
183.5 Hz
186.2 Hz
Table 2 (DCS Code Chart)
030
031
032
033
034
035
036
037
038
039
040
041
042
043
044
165
172
174
205
212
223
225
226
243
244
245
246
251
252
255
045
046
047
048
049
050
051
052
053
054
055
056
057
058
059
261
263
265
266
271
274
306
311
315
325
331
332
343
346
351
060
061
062
063
064
065
066
067
068
069
070
071
072
073
074
036
037
038
039
040
041
042
043
044
356
364
365
371
411
412
413
423
431
432
445
446
452
454
455
189.9 Hz
192.8 Hz
196.6 Hz
199.5 Hz
203.5 Hz
206.5 Hz
210.7 Hz
218.1 Hz
225.7 Hz
075
076
077
078
079
080
081
082
083
084
085
086
087
088
089
462
464
465
466
503
506
516
523
526
532
546
565
606
612
624
045
046
047
048
049
-
229.1 Hz
233.6 Hz
241.8 Hz
250.3 Hz
254.1 Hz
-
090
091
092
093
094
095
096
097
098
099
100
101
102
103
-
627
631
632
654
662
664
703
712
723
731
732
734
743
754
-
DIMMER
1
2
D
A
3
1
2
3
D
A
;
1
2
D
A
4
5
6
7
8
P1 P1 P2 P2 P3 P3
3
9
10
;
4
5
6
7
8
9
10
4
5
6
7
8
9
10
P1 P1 P2 P2 P3 P3
P100: Fixed
P2 01 - 02: LED Indicators Brightness Level
P3 00 - 15: TFT Display Brightness Level
;
MIC DWN
1
2
3
D
N
;
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
5
6
7
~
~
n-1
n
P2
;
DATE AND TIME
1
2
D
T
3
4
P1 P2 P2 P2 P2
1
2
3
4
D
T
P1
;
3
4
1
2
D
T
5
6
7
8
9
10
5
6
7
~
~
n-1
n
P2
;
P1 P2 P2 P2 P2
P1
P2
0: Date
1: Time (UTC)
2: Time differential (Time Zone)
P1=0 yyyymmdd (Year/Month/Date)
P1=1 hhmmss (Hour/Minute/Second, 24 hour time system)
P1=2 hhmm (Hour/Minute, 30 minute increments)
6
FT-991 CAT Operation Manual
CAT (Computer Aided Transceiver) Operation
ED
Set
Read
Answer
EK
Set
Read
Answer
EU
Set
Read
Answer
EX
Set
Read
Answer
P1
001
002
003
004
005
006
007
008
009
010
011
012
013
014
015
016
017
018
019
020
021
022
023
024
025
026
027
028
029
030
031
032
033
034
035
036
037
038
039
040
041
042
ENCORDER DOWN
1
2
E
D
3
4
5
7
8
9
10
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
4
5
6
7
8
9
10
P1 P2 P2
6
;
P1
P2
0: MAIN ENCORDER
1: SUB ENCORDER
8: MULTI ENCORDER
01 - 99: Steps
P1
P2
0: MAIN ENCORDER
1: SUB ENCORDER
8: MULTI ENCORDER
01 - 99: Steps
ENT KEY
1
2
3
E
K
;
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
5
6
7
8
9
10
ENCORDER UP
1
2
E
U
3
4
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
3
4
5
6
7
~
~
n-1
n
P2
;
7
8
9
10
7
~
~
n-1
n
P2
;
P1 P2 P2
;
MENU
1
2
E
X
1
2
E
X
1
2
E
X
P1 P1 P1 P2 P2
3
4
5
P1 P1 P1
3
4
5
6
;
6
P1 P1 P1 P2 P2
Function
AGC FAST DELAY
AGC MID DELAY
AGC SLOW DELAY
HOME FUNCTION
MY CALL INDICATION
DISPLAY COLOR
DIMMER LED
DIMMER TFT
BAR MTR PEAK HOLD
DVS RX OUT LEVEL
DVS TX OUT LEVEL
KEYER TYPE
KEYER DOT/DASH
CW WEIGHT
BEACON INTERVAL
NUMBER STYLE
CONTEST NUMBER
CW MEMORY 1
CW MEMORY 2
CW MEMORY 3
CW MEMORY 4
CW MEMORY 5
NB WIDTH
NB REJECTION
NB LEVEL
BEEP LEVEL
TIME ZONE
GPS/232C SELECT
232C RATE
232C TOT
CAT RATE
CAT TOT
CAT RTS
MEM GROUP
QUICK SPLIT FREQ
TX TOT
MIC SCAN
MIC SCAN RESUME
REF FREQ ADJ
CLAR MODE SELECT
AM LCUT FREQ
AM LCUT SLOPE
P1 : 001 - 151 (MENU Number)
P2 : Parameter (See Table)
P2
20 ~ 4000 msec (P2= 0020 ~ 4000, 20 msec/step)
20 ~ 4000 msec (P2= 0020 ~ 4000, 20 msec/step)
20 ~ 4000 msec (P2= 0020 ~ 4000, 20 msec/step)
0: SCOPE 1: FUNCTION
0 ~ 5 sec
0: BLUE 1: GRAY 2: GREEN 3: ORANGE 4: PURPLE 5: RED 6: SKY BLUE
0: 1 1: 2
00 ~ 15
0: OFF 1: 0.5 sec 2: 1.0 sec 3: 2.0 sec
0 ~ 100 (P2 = 000 ~ 100)
0 ~ 100 (P2 = 000 ~ 100)
0: OFF 1: BUG 2: ELEKEY-A 3: ELEKEY-B 4: ELEKEY-Y 5: ACS
0: NORNAL 1: REVERSE
2.5 ~ 4.5 (P2 = 25 ~ 45)
OFF / 1 ~ 690 sec (P2 = 000 ~ 690, 000: OFF)
0: 1290 1: AUNO 2: AUNT 3: A2NO 4: A2NT 5: 12NO 6: 12NT
0000 ~ 9999
0: TEXT 1: MESSAGE
0: TEXT 1: MESSAGE
0: TEXT 1: MESSAGE
0: TEXT 1: MESSAGE
0: TEXT 1: MESSAGE
0: 1 ms 1: 3 ms 2: 10 ms
0: 10 dB 1: 30 dB 2: 50 dB
0 ~ 10 (P2 = 00 ~ 10)
0 ~ 100 (P2 = 000 ~ 100)
UTC –12:00 ~ +14:00
0: GPS 1: RS232C
0: 4800 bps 1: 9600 bps 2: 19200 bps 3: 38400 bps
0: 10 msec 1: 100 msec 2: 1000 msec 3: 3000 msec
0: 4800 bps 1: 9600 bps 2: 19200 bps 3: 38400 bps
0: 10 msec 1: 100 msec 2: 1000 msec 3: 3000 msec
0: DISABLE 1: ENABLE
0: DISABLE 1: ENABLE
–20 kHz ~ +00 (or –00) ~ +20 kHz (P2= –20 ~ +00 or –00 ~ +20)
0 (OFF) ~ 30 min (P2= 00 ~ 30)
0: DISABLE 1: ENABLE
0: PAUSE 1: TIME
–25 ~ +00 (or –00) ~ +25 (P2= –25 ~ +00 or –00 ~ +25)
0: RX 1: TX 2: TRX
00: OFF 01: 100 Hz ~ 19: 1000 Hz (50 Hz steps)
0: 6 dB/oct 1: 18 dB/oct
7
Digits
4
4
4
1
1
1
1
2
1
3
3
1
1
2
3
1
4
1
1
1
1
1
1
1
2
3
5
1
1
1
1
1
1
1
3
2
1
1
3
1
2
1
FT-991 CAT Operation Manual
CAT (Computer Aided Transceiver) Operation
P1
043
044
045
046
047
048
049
050
051
052
053
054
055
056
057
058
059
060
061
062
063
064
065
066
067
068
069
070
071
072
073
074
075
076
077
078
079
080
081
082
083
084
085
086
087
088
089
090
091
092
093
094
095
096
097
098
099
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
Function
AM HCUT FREQ
AM HCUT SLOPE
AM MIC SELECT
AM OUT LEVEL
AM PTT SELECT
AM PORT SELECT
AM DATA GAIN
CW LCUT FREQ
CW LCUT SLOPE
CW HCUT FREQ
CW HCUT SLOPE
CW OUT LEVEL
CW AUTO MODE
CW BK-IN TYPE
CW BK-IN DELAY
CW WAVE SHAPE
CW FREQ DISPLAY
PC KEYING
QSK DELAY TIME
DATA MODE
PSK TONE
OTHER DISP (SSB)
OTHER SHIFT (SSB)
DATA LCUT FREQ
DATA LCUT SLOPE
DATA HCUT FREQ
DATA HCUT SLOPE
DATA IN SELECT
DATA PTT SELECT
DATA PORT SELECT
DATA OUT LEVEL
FM MIC SELECT
FM OUT LEVEL
FM PKT PTT SELECT
FM PKT PORT SELECT
FM PKT TX GAIN
FM PKT MODE
RPT SHIFT 28MHz
RPT SHIFT 50MHz
RPT SHIFT 144MHz
RPT SHIFT 430MHz
ARS 144MHz
ARS 430MHz
DCS POLARITY
RADIO ID
DIGITAL SQL TYPE
DIGITAL SQL CODE
GM DISPLY
DISTANCE
AMS TX MODE
STANDBY BEEP
RTTY LCUT FREQ
RTTY LCUT SLOPE
RTTY HCUT FREQ
RTTY HCUT SLOPE
RTTY SHIFT PORT
RTTY POLARITY-RX
RTTY POLARITY-TX
RTTY OUT LEVEL
RTTY SHIFT FREQ
RTTY MARK FREQ
SSB LCUT FREQ
SSB LCUT SLOPE
SSB HCUT FREQ
SSB HCUT SLOPE
SSB MIC SELECT
SSB OUT LEVEL
SSB PTT SELECT
SSB PORT SELECT
SSB TX BPF
APF WIDTH
CONTOUR LEVEL
CONTOUR WIDTH
IF NOTCH WIDTH
SCP DISPLAY MODE
SCP START CYCLE
ASC DIAL SPEED
SCP SPAN FREQ
PRMTRC EQ1 FREQ
PRMTRC EQ1 LEVEL
PRMTRC EQ1 BWTH
PRMTRC EQ2 FREQ
P2
00: OFF 01: 700 Hz ~ 67: 4000 Hz (50 Hz steps)
0: 6 dB/oct 1: 18 dB/oct
0: MIC 1: REAR
0 ~ 100 (P2 = 000 ~ 100)
0: DAKY 1: RTS 2: DTR
0: DATA 1: USB
0 ~ 100 (P2 = 000 ~ 100)
00: OFF 01: 100 Hz ~ 19: 1000 Hz (50 Hz steps)
0: 6 dB/oct 1: 18 dB/oct
00: OFF 01: 700 Hz ~ 67: 4000 Hz (50 Hz steps)
0: 6 dB/oct 1: 18 dB/oct
0 ~ 100 (P2 = 000 ~ 100)
0: OFF 1: 50 MHz 2: ON
0: SEMI BREAK-IN 1: FULL BREAK-IN
30 ~ 3000 msec (P2 = 0030 ~ 3000, 10 msec/step)
0: 1 msec 1: 2 msec 2: 4 msec 3: 6 msec
0: DIRECT FREQ 1: PITCH OFFSET
0: OFF 1: DAKY 2: RTS 3: DTR
0: 15 msec 1: 20 msec 2: 25 mesc 3: 30 msec
0: PSK 1: OTHER
0: 1000 Hz 1: 1500 Hz 2: 2000 Hz
–3000 Hz ~ 0 ~ +3000 Hz (P2 = –3000 ~ –0000 or +0000 ~ +3000, 10 Hz steps)
–3000 Hz ~ 0 ~ +3000 Hz (P2 = –3000 ~ –0000 or +0000 ~ +3000, 10 Hz steps)
00: OFF 01: 100 Hz ~ 19: 1000 Hz (50 Hz steps)
0: 6 dB/oct 1: 18 dB/oct
00: OFF 01: 700 Hz ~ 67: 4000 Hz (50 Hz steps)
0: 6 dB/oct 1: 18 dB/oct
0: MIC 1: REAR
0: DAKY 1: RTS 2: DTR
1: DATA 2: USB
0 ~ 100 (P2 = 000 ~ 100)
0: MIC 1: REAR
0 ~ 100 (P2 = 000 ~ 100)
0: DAKY 1: RTS 2: DTR
1: DATA 2: USB
0 ~ 100 (P2 = 000 ~ 100)
0: 1200 1: 9600
0 ~ 1000 kHz (P2 = 0000 ~ 1000, 10 kHz/step)
0 ~ 4000 kHz (P2 = 0000 ~ 4000, 10 kHz/step)
0 ~ 4000 kHz (P2 = 0000 ~ 4000, 10 kHz/step)
0 ~ 10000 kHz (P2 = 0000 ~ 10000, 10 kHz/step)
0: OFF 1: ON
0: OFF 1: ON
0: Tn-Rn 1: Tn-Riv 2: Tiv-Rn 3: Tiv-Riv
---------0: OFF 1: CODE 2: BREAK
001 ~ 126
0: DISTANCE 1: STRENGTH
0: km 1: mile
0: AUTO 1: MANUAL 2: DN 3: VW 4: ANALOG
0: OFF 1: ON
00: OFF 01: 100 Hz ~ 19: 1000Hz (50 Hz steps)
0: 6 dB/oct 1: 18 dB/oct
00: OFF 01: 700 Hz ~ 67: 4000Hz (50 Hz steps)
0: 6 dB/oct 1: 18 dB/oct
0: SHIFT 1: DTR 2: RTS
0: NORNAL 1: REVERSE
0: NORNAL 1: REVERSE
0 ~ 100 (P2 = 000 ~ 100)
1: 170 Hz 1: 200 Hz 2: 425 Hz 3: 850 Hz
1: 1275 Hz 2: 2125 Hz
00: OFF 01: 100 Hz ~ 19: 1000 Hz (50 Hz steps)
0: 6 dB/oct 1: 18 dB/oct
00: OFF 01: 700 Hz ~ 67: 4000 Hz (50 Hz steps)
0: 6 dB/oct 1: 18 dB/oct
0: MIC 1: REAR
0 ~ 100 (P2 = 000 ~ 100)
0: DAKY 1: RTS 2: DTR
0: DATA 1: USB
0: 50 ~ 3000 1: 100 ~ 2900 2: 200 ~ 2800 3: 300 ~ 2700 4: 400 ~ 2600
0: NARROW 1: MEDIUM 2: WIDE
–40 ~ 0 ~ +20 (P2 = –40 ~ –00 or +00 ~ +20)
01 ~ 11
0: NARROW 1: WIDE
0: SPECTRAM 1: WATER FALL
0: OFF 1: 3 sec 2: 5 sec 3: 10 sec
0: 0.25 kHz/sec 1: 0.5 kHz/sec 2: 1 kHz/sec 3: 2 kHz/sec 4: 4 kHz/sec 5: DISABLE
03: 50 kHz 04: 100 kHz 05: 200 kHz 06: 500 kHz 07: 1000 kHz
00 : OFF 01: 100 02: 200 03: 300 04: 400 05: 500 06: 600 07: 700 Hz
–20 ~ 0 ~ +10 (P2 = –20 ~ –00 or +00 ~ +10)
01 ~ 10
00: OFF 01: 700 02: 800 03: 900 04: 1000 05: 1100 06: 1200 07: 1300 08: 1400
8
09: 1500 Hz
Digits
2
1
1
3
1
1
3
2
1
2
1
3
1
1
4
1
1
1
1
1
1
5
5
2
1
1
2
1
1
1
3
1
3
1
1
3
1
4
4
4
5
1
1
1
1
3
1
1
1
1
2
1
2
1
1
1
1
3
1
1
2
1
2
1
1
3
1
1
1
1
3
2
1
1
1
1
2
2
3
2
2
FT-991 CAT Operation Manual
CAT (Computer Aided Transceiver) Operation
P1
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
Function
PRMTRC EQ2 LEVEL
PRMTRC EQ2 BWTH
PRMTRC EQ3 FREQ
PRMTRC EQ3 LEVEL
PRMTRC EQ3 BWTH
P-PRMTRC EQ1 FREQ
P-PRMTRC EQ1 LEVEL
P-PRMTRC EQ1 BWTH
P-PRMTRC EQ2 FREQ
P-PRMTRC EQ2 LEVEL
P-PRMTRC EQ2 BWTH
P-PRMTRC EQ3 FREQ
P-PRMTRC EQ3 LEVEL
P-PRMTRC EQ3 BWTH
HF TX MAX POWER
50M TX MAX POWER
144M TX MAX POWER
430M TX MAX POWER
TUNER SELECT
VOX SELECT
VOX GAIN
VOX DELAY
ANTI VOX GAIN
DATA VOX GAIN
DATA VOX DELAY
ANTI DVOX GAIN
EMERGENCY FREQ TX
FA
Set
Read
Answer
FB
Set
Read
Answer
FS
Set
Read
Answer
FT
Set
Read
Answer
P2
–20 ~ 0 ~ +10 (P2 = –20 ~ –00 or +00 ~ +10)
01 ~ 10
00 : OFF 01: 1500 02: 1600 03: 1700 04: 1800 05: 1900 06: 2000 ~ 18: 3200 Hz
–20 ~ 0 ~ +10 (P2 = –20 ~ –00 or +00 ~ +10)
01 ~ 10
00 : OFF 01: 100 02: 200 03: 300 04: 400 05: 500 06: 600 07: 700 Hz
–20 ~ 0 ~ +10 (P2 = –20 ~ –00 or +00 ~ +10)
01 ~ 10
00: OFF 01: 700 02: 800 03: 900 04: 1000 05: 1100 06: 1200 07: 1300 08: 1400
–20 ~ 0 ~ +10 (P2 = –20 ~ –00 or +00 ~ +10)
01 ~ 10
00 : OFF 01: 1500 02: 1600 03: 1700 04: 1800 05: 1900 06: 2000 ~ 18: 3200 Hz
–20 ~ 0 ~ +10 (P2 = –20 ~ –00 or +00 ~ +10)
01 ~ 10
5 ~ 100 (P2 = 005 ~ 100)
5 ~ 100 (P2 = 005 ~ 100)
5 ~ 50 (P2 = 005 ~ 050)
5 ~ 50 (P2 = 005 ~ 050)
0: OFF 1: INTERNAL 2: EXTERNAL 3: ATAS 4: LAMP
0: MIC 1: DATA
000 ~ 100
30 ~ 3000 msec (P2 = 0030 ~ 3000, 10 msec/step)
000 ~ 100
000 ~ 100
30 ~ 3000 msec (P2 = 0030 ~ 3000)
000 ~ 100
0: DISABLE 1: ENABLE
09: 1500 Hz
Digits
3
2
2
3
2
2
3
2
2
3
2
2
3
2
3
3
3
3
1
1
3
4
3
3
4
3
1
FREQUENCY VFO-A
1
2
F
A
P1 P1 P1 P1 P1 P1 P1 P1
3
11
12
13
14
15
16
17
18
19
20
P1
;
4
5
6
7
8
9
10
4
5
6
7
8
9
10
1
2
3
F
A
;
3
4
5
6
7
8
9
10
1
2
F
A
P1 P1 P1 P1 P1 P1 P1 P1
11
12
13
P1
;
14
15
16
17
18
19
20
6
7
8
9
10
P1 000030000 - 470000000 (Hz)
FREQUENCY VFO-B
1
2
F
B
P1 P1 P1 P1 P1 P1 P1 P1
3
11
12
13
14
15
16
17
18
19
20
P1
;
4
5
6
7
8
9
10
4
5
6
7
8
9
10
1
2
3
F
B
;
3
4
5
1
2
F
B
P1 P1 P1 P1 P1 P1 P1 P1
11
12
13
P1
;
14
15
16
17
18
19
20
5
6
7
8
9
10
P1 000030000 - 470000000 (Hz)
FAST STEP
1
2
3
4
F
S
P1
;
1
2
3
4
5
6
7
8
9
10
F
S
;
5
6
7
8
9
10
5
6
7
8
9
10
1
2
3
4
F
S
P1
;
P1 0: VFO-A FAST Key “OFF”
1: VFO-A FAST Key “ON”
FUNCTION TX
1
2
3
4
F
T
P1
;
1
2
3
4
5
6
7
8
9
10
F
T
;
5
6
7
8
9
10
1
2
3
4
F
T
P2
;
P1
P2
2: VFO-A Band Transmitter: TX
3: VFO-B Band Transmitter: TX
0: VFO-A Band Transmitter: TX
1: VFO-B Band Transmitter: TX
9
FT-991 CAT Operation Manual
CAT (Computer Aided Transceiver) Operation
GT
Set
Read
Answer
ID
Set
Read
Answer
IF
Set
Read
Answer
AGC FUNCTION
1
2
G
T
3
4
P1 P2
1
2
3
4
G
T
P1
;
3
4
1
2
G
T
P1 P3
5
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
;
;
IDENTIFICATION
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
I
D
;
4
5
6
7
8
9
10
10
1
2
I
D
3
P1 P1 P1 P1
INFORMATION
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
I
F
;
4
5
6
7
8
9
1
2
I
F
P1 P1 P1 P2 P2 P2 P2
3
11
12
13
14
15
16
17
Read
Answer
KM
Set
Read
Answer
KP
Set
Read
Answer
KR
Set
Read
Answer
18
19
P2 P2 P2 P2 P3 P3 P3 P3 P3
21
Set
P1 0570: FT-991
;
22
23
24
25
26
27
P5 P6 P7 P8 P9 P9 P10
IS
P1 0: Fixed
P3 0: AGC “OFF”
P2 0: AGC “OFF”
1: AGC “FAST”
1: AGC “FAST”
2: AGC “MID”
2: AGC “MID”
3: AGC “SLOW”
3: AGC “SLOW”
4: AGC “AUTO-FAST”
4: AGC “AUTO”
5: AGC “AUTO-MID”
6: AGC “AUTO-SLOW”
28
29
;
P1 000-117 (Memory Channel)
P2 VFO-A Frequency (Hz)
P3 Clarifier Direction +: Plus Shift, --: Minus Shift
Clarifier Offset: 0000 - 9999 (Hz)
10
P4 0: RX CLAR “OFF” 1: RX CLAR “ON”
P5 0: TX CLAR “OFF”
1: TX CLAR “ON”
2: USB 3: CW 4: FM 5: AM 6: RTTY-LSB 7: CW-R
10 P6 MODE 1: LSB
8: DATA-LSB 9: RTTY-USB A: DATA-FM B: FM-N C: DATA-USB
P2 D: AM-N E: C4FM
2: Memory Tune 3: Quick Memory Bank (QMB)
20 P7 0: VFO 1: Memory
4: QMB-MT 5: PMS 6: HOME
P4 P8 0: CTCSS “OFF” 1: CTCSS ENC/DEC 2: CTCSS ENC
30 P9 00: (Fixed)
P100: Simplex 1: Plus Shift 2: Minus Shift
IF-SHIFT
1
2
I
S
3
4
1
2
3
4
I
S
P1
;
3
4
1
2
I
S
5
6
7
8
P1 -/+ P2 P2 P2 P2
9
10
;
5
6
7
8
9
10
5
6
7
8
9
10
P1 -/+ P2 P2 P2 P2
P10:Fixed
P2 -1000 ~ +1000 Hz (20 Hz steps)
;
KEYER MEMORY
1
2
K
M
3
4
1
2
3
4
K
M
P1
;
3
4
1
2
K
M
5
6
7
P1 P2 P2 P2 P2
~
~
53
n
P2
;
5
6
7
8
9
10
5
6
7
~
~
n-1
n
P2
;
P1 P2 P2 P2 P2
P1 1 - 5 : Keyer Memory Channel Number
P2 Message Characters (up to 50 characters)
KEY PITCH
1
2
K
P
3
1
2
3
K
P
;
1
2
K
P
4
P1 P1
3
5
6
7
8
9
10
;
4
5
6
7
8
9
10
4
5
6
7
8
9
10
5
6
7
8
9
10
P1 P1
P1 00: 300 Hz - 75: 1050 Hz (10Hz steps)
;
KEYER
1
2
3
4
K
R
P1
;
1
2
3
4
5
6
7
8
9
10
K
R
;
5
6
7
8
9
10
1
2
3
4
K
R
P1
;
P1 0: KEYER “OFF”
1: KEYER “ON”
10
FT-991 CAT Operation Manual
CAT (Computer Aided Transceiver) Operation
KS
Set
Read
Answer
KY
Set
Read
Answer
LK
Set
Read
Answer
LM
Set
Read
Answer
MA
Set
Read
Answer
MC
Set
Read
Answer
MD
Set
Read
Answer
KEY SPEED
1
2
K
S
3
1
2
3
K
S
;
1
2
K
S
4
5
P1 P1 P1
3
6
7
8
9
10
;
4
5
6
7
8
9
10
4
5
6
7
8
9
10
P1 P1 P1
P1 004 - 060 (WPM)
;
CW KEYING
1
2
3
4
K
Y
P1
;
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
5
6
7
8
9
10
P1
1: Keyer Memory “1” Playback
2: Keyer Memory “2” Playback
3: Keyer Memory “3” Playback
4: Keyer Memory “4” Playback
5: Keyer Memory “5” Playback
6: Message Keyer “1” Playback
7: Message Keyer “2” Playback
8: Message Keyer “3” Playback
9: Message Keyer “4” Playback
A: Message Keyer “5” Playback
LOCK
1
2
3
4
L
K
P1
;
1
2
3
4
5
6
7
8
9
10
L
K
;
5
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
1
2
3
4
L
K
P1
;
P1 0: VFO-A DIAL Lock “OFF”
1: VFO-A DIAL Lock “ON”
LOAD MESSEGE
1
2
L
M
3
4
P1 P2
1
2
3
4
L
M
P1
;
3
4
1
2
L
M
P1 P2
;
;
P1 0: DVS
P2
0: DVS (Recording Stop)
1: DVS (CH “1” Recording Start/Stop)
2: DVS (CH “2” Recording Start/Stop)
3: DVS (CH “3” Recording Start/Stop)
4: DVS (CH “4” Recording Start/Stop)
5: DVS (CH “5” Recording Start/Stop)
MEMORY CHANNEL TO VFO-A
1
2
3
M
A
;
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
6
7
8
9
10
MEMORY CHANNEL
1
2
M
C
3
1
2
3
M
C
;
1
2
M
C
4
5
P1 P1 P1
3
;
4
5
6
7
8
9
10
4
5
6
7
8
9
10
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
P1 P1 P1
P1 000 - 117: Memory Channel Number
000 - 099: Regular Memory Channel
100: P-1L 101: P-1U ~ 116: P-9L
117: P-9U
;
OPERATING MODE
1
2
M
D
3
4
P1 P2
1
2
3
4
M
D
P1
;
3
4
1
2
M
D
P1 P2
5
;
P1 0: MAIN RX
P2 MODE
1: LSB 2: USB 3: CW-U 4: FM 5: AM 6: RTTY-LSB
7: CW-L 8: DATA-LSB 9: RTTY-USB A: DATA-FM
B: FM-N C: DATA-USB D: AM-N E: C4FM
;
11
FT-991 CAT Operation Manual
CAT (Computer Aided Transceiver) Operation
MG
Set
Read
Answer
ML
Set
Read
Answer
MR
Set
Read
Answer
MIC GAIN
1
2
M
G
3
1
2
3
M
G
;
1
2
M
G
4
5
P1 P1 P1
3
6
7
8
9
10
;
4
5
6
7
8
9
10
4
5
6
7
8
9
10
7
8
9
10
P1 P1 P1
;
MONITOR LEVEL
1
2
M
L
3
4
1
2
3
4
M
L
P1
;
3
4
1
2
M
L
5
6
P1 P2 P2 P2
;
5
6
7
8
9
10
5
6
7
8
9
10
10
P1 P2 P2 P2
;
1
2
1
2
M
R
3
4
5
6
7
8
9
3
4
5
6
7
8
9
7
8
9
P0 P0 P0
3
4
1
2
R
P1 P1 P1 P2 P2 P2 P2
11
12
13
14
5
;
M
15
6
16
17
Read
Answer
MW
Set
22
23
24
25
26
27
1
2
3
4
M
S
P1
;
1
2
3
M
S
;
MX
Set
Read
Answer
NA
Set
Read
Answer
28
29
;
5
6
7
8
9
10
4
5
6
7
8
9
10
5
6
7
8
9
10
8
9
10
1
2
3
4
M
S
P1
;
P1
0: COMP
1: ALC
2: PO
3: SWR
4: ID
5: VDD
MEMORY CHANNEL WRITE
1
2
M
W
P1 P1 P1 P2 P2 P2 P2 P2 P3 Clarifier Direction +: Plus Shift, --: Minus Shift
3
4
11
12
13
14
5
15
6
16
7
17
18
19
20
P1 000-117 (Memory Channel)
P2
Frequency (Hz)
Clarifier Offset: 0000 - 9999 (Hz)
P4 0: RX CLAR “OFF” 1: RX CLAR “ON”
1: TX CLAR “ON”
P6 MODE 1: LSB 2: USB 3: CW 4: FM 5: AM 6: RTTY-LSB 7: CW-R
8: DATA-LSB 9: RTTY-USB A: DATA-FM B: FM-N C: DATA-USB
D: AM-N E: C4FM
P7 00: (Fixed)
P8 0: CTCSS “OFF” 1: CTCSS ENC/DEC 2: CTCSS ENC
P9 00: (Fixed)
P100: Simplex 1: Plus Shift 2: Minus Shift
P2 P2 P2 P2 P3 P3 P3 P3 P3 P4 P5 0: TX CLAR “OFF”
21
Answer
19
P0/1 000-117 (Memory Channel)
P2 VFO-A Frequency (Hz)
P3 Clarifier Direction +: Plus Shift, --: Minus Shift
Clarifier Offset: 0000 - 9999 (Hz)
10
P4 0: RX CLAR “OFF” 1: RX CLAR “ON”
P5 0: TX CLAR “OFF”
1: TX CLAR “ON”
10 P6 MODE 1: LSB
2: USB 3: CW 4: FM 5: AM 6: RTTY-LSB 7: CW-R
8: DATA-LSB 9: RTTY-USB A: DATA-FM B: FM-N C: DATA-USB
P2 D: AM-N E: C4FM
20
P7 0: VFO 1: Memory
P4 P8 0: CTCSS “OFF” 1: CTCSS ENC/DEC 2: CTCSS ENC
30 P9 00: (Fixed)
P100: Simplex 1: Plus Shift 2: Minus Shift
METER SW
22
23
24
25
26
27
P5 P6 P7 P8 P9 P9 P10
Read
18
P2 P2 P2 P2 P3 P3 P3 P3 P3
21
Set
P1 0: MONI “ON/OFF”
1: MONI Level
P2P1=0
000: MONI “OFF”
001: MONI “ON”
P1=1
000 - 100
MEMORY CHANNEL READ
P5 P6 P7 P8 P9 P9 P10
MS
P1 000 - 100
28
29
30
;
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
5
6
7
8
9
10
MOX SET
1
2
3
4
M
X
P1
;
1
2
3
4
5
6
7
8
9
10
M
X
;
5
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
1
2
3
4
M
X
P1
;
P1 0: MOX “OFF”
1: MOX “ON”
NARROW
1
2
M
A
3
4
P1 P2
1
2
3
4
M
A
P1
;
3
4
1
2
M
A
P1 P2
;
P1 0: Fixed
P2 0: OFF
1: ON
;
12
FT-991 CAT Operation Manual
CAT (Computer Aided Transceiver) Operation
NB
Set
Read
Answer
NL
Set
Read
Answer
NR
Set
Read
Answer
OI
Set
Read
Answer
NOISE BLANKER STATUS
1
2
N
B
3
4
P1 P2
1
2
3
4
N
B
P1
;
3
4
1
2
N
B
P1 P2
5
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
7
8
9
10
;
;
NOISE BLANKER LEVEL
1
2
N
L
3
4
1
2
3
4
N
L
P1
;
3
4
1
2
N
L
5
6
P1 P2 P2 P2
;
5
6
7
8
9
10
5
6
7
8
9
10
P1 P2 P2 P2
NOISE REDUCTION
1
2
N
R
3
4
P1 P2
1
2
3
4
N
R
P1
;
3
4
1
2
N
R
P1 P2
5
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
10
;
Read
Answer
PA
Set
Read
Answer
PB
Set
Read
Answer
P1 0: Fixed
P2 0: Noise Reduction “OFF”
1: Noise Reduction “ON”
;
OPPOSITE BAND INFORMATION
1
2
3
4
5
6
7
8
9
4
5
6
7
8
9
4
5
6
7
8
9
1
2
3
O
I
;
1
2
O
I
11
12
3
P1 P1 P1 P2 P2 P2 P2
13
14
15
16
17
18
19
P2 P2 P2 P2 P3 P3 P3 P3 P3
21
Set
P1 0: Fixed
P2 000 - 010
;
22
23
24
25
26
27
P5 P6 P7 P8 P9 P9 P10
OS
P1 0: Fixed
P2 0: Noise Blanker “OFF”
1: Noise Blanker “ON”
28
29
;
P1 000-117 (Memory Channel)
P2 VFO-B Frequency (Hz)
P3 Clarifier Direction +: Plus Shift, --: Minus Shift
Clarifier Offset: 0000 - 9999 (Hz)
10
P4 0: RX CLAR “OFF” 1: RX CLAR “ON”
P5 0: TX CLAR “OFF”
1: TX CLAR “ON”
10 P6 MODE 1: LSB
2: USB 3: CW 4: FM 5: AM 6: RTTY-LSB 7: CW-R
8: DATA-LSB 9: RTTY-USB A: DATA-FM B: FM-N C: DATA-USB
P2 D: AM-N E: C4FM
20
P7 0: VFO 1: Memory
P4 P8 0: CTCSS “OFF” 1: CTCSS ENC/DEC 2: CTCSS ENC
30 P9 00: (Fixed)
P100: Simplex 1: Plus Shift 2: Minus Shift
OFFSET (REPEATER SHIFT)
1
2
O
S
3
4
P1 P2
1
2
3
4
O
S
P1
;
3
4
1
2
O
S
P1 P2
5
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
;
P1 0: Fixed
P2 0: Simplex
1: Plus Shift
2: Minus Shift
*: This command can be activated only with an FM mode.
;
PRE-AMP (IPO)
1
2
P
A
3
4
P1 P2
1
2
3
4
P
A
P1
;
3
4
1
2
P
A
P1 P2
5
;
P10:Fixed
P2 0: IPO
1: AMP 1
2: AMP 2
;
PLAY BACK
1
2
P
B
3
4
P1 P2
1
2
3
4
P
B
P1
;
3
4
1
2
P
B
P1 P2
5
;
;
P1 0: DVS
P2
13
0: DVS (Playback Stop)
1: DVS (CH “1” Playback Start)
2: DVS (CH “2” Playback Start)
3: DVS (CH “3” Playback Start)
4: DVS (CH “4” Playback Start)
5: DVS (CH “5” Playback Start)
FT-991 CAT Operation Manual
CAT (Computer Aided Transceiver) Operation
PC
Set
Read
Answer
PL
Set
Read
Answer
PR
Set
Read
Answer
PS
Set
Read
Answer
QI
Set
Read
Answer
QR
Set
Read
Answer
QS
Set
Read
Answer
RA
Set
Read
Answer
POWER CONTROL
1
2
P
C
3
1
2
3
P
C
;
1
2
P
C
4
5
P1 P1 P1
3
6
7
8
9
10
;
4
5
6
7
8
9
10
4
5
6
7
8
9
10
7
8
9
10
P1 P1 P1
P1 005 -100
;
SPEECH PROCESSOR LEVEL
1
2
P
L
3
1
2
3
P
L
;
1
2
P
L
4
5
P1 P1 P1
3
6
;
4
5
6
7
8
9
10
4
5
6
7
8
9
10
P1 P1 P1
P1 000 -100
;
SPEECH PROCESSOR LEVEL
1
2
P
R
3
4
P1 P2
1
2
3
4
P
R
P1
;
3
4
1
2
P
R
P1 P2
5
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
;
P1
P2
0: Speech Processor
1: Parametric Microphone Equalizer
1: “OFF”
2: “ON”
;
POWER SWITCH
1
2
3
4
P
S
P1
;
4
5
6
7
8
9
10
5
6
7
8
9
10
4
5
6
7
8
9
10
1
2
3
P
S
;
1
2
3
4
P
S
P1
;
P1 0: POWER “OFF”
1: POWER “ON”
This command requires dummy data be initially sent. Then after one second and before two seconds the command is sent.
QMB STORE
1
2
3
Q
I
;
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
4
5
6
7
8
9
10
QMB RECALL
1
2
3
Q
R
;
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
4
5
6
7
8
9
10
QUICK SPLIT
1
2
3
Q
S
;
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
RF ATTENUATOR
1
2
R
A
3
4
P1 P2
1
2
3
4
R
A
P1
;
3
4
1
2
R
A
P1 P2
;
P1 0: Fixed
P2 0: OFF
1: ON
;
14
FT-991 CAT Operation Manual
CAT (Computer Aided Transceiver) Operation
RC
Set
Read
Answer
RD
Set
Read
Answer
RG
Set
Read
Answer
RI
Set
Read
Answer
RL
Set
Read
Answer
RM
Set
Read
Answer
RS
Set
Read
Answer
RT
Set
Read
Answer
CLAR CLEAR
1
2
3
R
C
;
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
4
5
6
7
8
9
10
CLAR DOWN
1
2
R
D
3
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
3
4
5
6
7
8
9
10
P1 P1 P1 P1
;
P1 0000 - 9999 (Hz)
RF GAIN
1
2
R
G
P1 P2 P2 P2
1
2
3
4
R
G
P1
;
3
4
1
2
R
G
;
5
6
7
8
9
10
5
6
7
8
9
10
P1 P2 P2 P2
P1 0: Fixed
P2 000 - 255
;
RADIO INFORMATION
1
2
3
4
5
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
7
8
9
10
1
2
3
4
R
I
P1
;
1
2
3
4
R
I
P1 P2
;
P1
0: Hi-SWR
A: TX LED
P2 0: OFF
3: REC
1: ON
4: PLAY
5: VFO-A TX
6: VFO-B TX
7: VFO-A RX
NOISE REDUCTION LEVEL
1
2
R
L
3
4
1
2
3
4
R
L
P1
;
3
4
1
2
R
L
5
P1 P2 P2
6
;
5
6
7
8
9
10
5
6
7
8
9
10
P1 P2 P2
P1 0: Fixed
P2 01 - 15
;
READ METER
1
2
3
4
5
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
1
2
3
4
R
M
P1
;
3
4
1
2
R
M
P1 P2 P2 P2
;
P1
P2
0: Depends on the front panel METER
1: S 2: Depends on the front panel METER
(PO / COMP / ALC / SWR / ID / VDD)
3: COMP
0 - 255
4: ALC
5: PO
6: SWR
7: ID
8: VDD
RADIO STATUS
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
R
S
;
5
6
7
8
9
10
5
6
7
8
9
10
1
2
3
4
R
S
P1
;
P1 0: NORMAL MODE
1: MENU MODE
CLAR
1
2
3
4
R
T
P1
;
1
2
3
4
5
6
7
8
9
10
R
T
;
5
6
7
8
9
10
1
2
3
4
R
T
P1
;
P1 0: RX Clarifier “OFF”
1: RX Clarifier “ON”
15
FT-991 CAT Operation Manual
CAT (Computer Aided Transceiver) Operation
RU
Set
Read
Answer
SC
Set
Read
Answer
SD
Set
Read
Answer
SH
Set
Read
Answer
RX CLARIFIER PLUS OFFSET
1
2
R
U
3
1
2
3
4
5
6
1
2
3
4
5
Set
Read
Answer
5
6
7
8
9
10
7
8
9
10
6
7
8
9
10
5
6
7
8
9
10
;
P1 0000 - 9999 (Hz)
SCAN
1
2
3
4
S
C
P1
;
1
2
3
4
5
6
7
8
9
10
S
C
;
5
6
7
8
9
10
8
9
10
1
2
3
4
S
C
P1
;
P1 0: Scan “OFF”
1: Scan “ON” (UP ward)
2: Scan “ON” (DOWN ward)
CW BREAK-IN DELAY TIME
1
2
S
D
3
1
2
3
S
D
;
1
2
S
D
4
5
6
P1 P1 P1 P1
3
7
;
4
5
6
7
8
9
10
4
5
6
7
8
9
10
7
8
9
10
P1 P1 P1 P1
P1 0030 - 3000 msec
;
WIDTH
1
2
S
H
3
4
1
2
3
4
S
H
P1
;
3
4
1
2
S
H
5
P1 P2 P2
6
;
5
6
7
8
9
10
5
6
7
8
9
10
P1 P2 P2
Command
P2
00 (Default)
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
SM
4
P1 P1 P1 P1
P1 0: Fixed
P2 00 (See Table)
;
SSB (Narrow)
1500 Hz
200 Hz
400 Hz
600 Hz
850 Hz
1100 Hz
1350 Hz
1500 Hz
1650 Hz
1800 Hz
-
Bandwidth
CW (Narrow)
CW (Wide)
500 Hz
2400 Hz
50 Hz
100 Hz
150 Hz
200 Hz
250 Hz
300 Hz
350 Hz
400 Hz
450 Hz
500 Hz
500 Hz
800 Hz
1200 Hz
1400 Hz
1700 Hz
2000 Hz
2400 Hz
3000 Hz
-
SSB (Wide)
2400 Hz
1800 Hz
1950 Hz
2100 Hz
2200 Hz
2300 Hz
2400 Hz
2500 Hz
2600 Hz
2700 Hz
2800 Hz
2900 Hz
3000 Hz
3200 Hz
RTTY/PSK (Narrow)
300 Hz
50 Hz
100 Hz
150 Hz
200 Hz
250 Hz
300 Hz
350 Hz
400 Hz
450 Hz
500 Hz
-
RTTY/PSK (Wide)
500 Hz
500 Hz
800 Hz
1200 Hz
1400 Hz
1700 Hz
2000 Hz
2400 Hz
3000 Hz
-
S-METER READING
1
2
3
4
5
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
1
2
3
4
S
M
P1
;
3
4
1
2
S
M
P1 P2 P2 P2
P1 0: Fixed
P2 000 - 255
;
16
FT-991 CAT Operation Manual
CAT (Computer Aided Transceiver) Operation
SQ
Set
Read
Answer
SV
Set
Read
Answer
TS
Set
Read
Answer
TX
Set
Read
Answer
UL
Set
Read
Answer
UP
Set
Read
Answer
VD
Set
Read
Answer
VG
Set
Read
Answer
SQUELCLH LEVEL
1
2
S
Q
3
4
1
2
3
4
S
Q
P1
;
3
4
1
2
S
Q
5
6
P1 P2 P2 P2
7
8
9
10
;
5
6
7
8
9
10
5
6
7
8
9
10
P1 P2 P2 P2
P1 0: Fixed
P2 000 - 100
;
SWAP VFO
1
2
3
S
V
;
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
5
6
7
8
9
10
TXW
1
2
3
4
T
S
P1
;
1
2
3
4
5
6
7
8
9
10
T
S
;
5
6
7
8
9
10
5
6
7
8
9
10
1
2
3
4
T
S
P1
;
P1 0: TXW “OFF”
1: TXW “ON”
TX SET
1
2
3
4
T
X
P1
;
1
2
3
4
5
6
7
8
9
10
T
X
;
5
6
7
8
9
10
1
2
3
4
T
X
P1
;
P1 0: RADIO TX “OFF” CAT TX “OFF”
1: RADIO TX “OFF” CAT TX “ON”
2: RADIO TX “ON” CAT TX “OFF” (Answer)
PLL UNLOCK STATUS
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
U
L
;
5
6
7
8
9
10
1
2
3
4
U
L
P1
;
4
5
6
7
8
9
10
P1 0: PLL “Lock”
1: PLL “Unlock”
UP
1
2
3
U
P
;
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
5
6
7
8
9
10
VOX DELAY TIME
1
2
V
D
3
1
2
3
V
D
;
1
2
V
D
4
P1 P1 P1 P1
3
;
4
5
6
7
8
9
10
4
5
6
7
8
9
10
7
8
9
10
P1 P1 P1 P1
P1 0030 - 3000 msec (10 msec multiples)
;
VOX GAIN
1
2
V
G
3
1
2
3
V
G
;
1
2
V
G
4
5
P1 P1 P1
3
6
;
4
5
6
7
8
9
10
4
5
6
7
8
9
10
P1 P1 P1
P1 000 - 100
;
17
FT-991 CAT Operation Manual
CAT (Computer Aided Transceiver) Operation
VM
Set
Read
Answer
VX
Set
Read
Answer
XT
Set
Read
Answer
ZI
Set
Read
Answer
VFO-A TO MEMORY CHANNEL
1
2
3
V
M
;
4
5
1
2
3
4
5
1
2
3
4
6
7
8
9
10
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
;
VOX STATUS
1
2
3
4
V
X
P1
;
1
2
3
4
5
6
7
8
9
10
V
X
;
5
6
7
8
9
10
5
6
7
8
9
10
1
2
3
4
V
X
P1
;
;
P1 0:VOX “OFF”
1:VOX “ON”
TX CLAR
1
2
3
4
X
T
P1
;
1
2
3
4
5
6
7
8
9
10
X
T
;
5
6
7
8
9
10
5
6
7
8
9
10
1
2
3
4
X
T
P1
;
;
P1 0:TX CLAR “OFF”
1:TX CLAR “ON”
ZERO IN
1
2
3
Z
I
;
4
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
;
(CW AUTO ZERO IN Function)
18
FT-991 CAT Operation Manual
Copyright 2015
YAESU MUSEN CO., LTD.
All rights reserved
No portion of this manual
may be reproduced without
the permission of
YAESU MUSEN CO., LTD.
1508-C0