Monogram® 48" Built-In Side-by-Side Refrigerator
ZISB480DH
SECTION 1
FLUSH INSET INSTALLATION
SECTION 2
STANDARD INSTALLATION
1/4" FRAMED PANELS
3/4" OVERLAY PANELS
Product Specification Revised 10/14
Monogram® 48" Built-In Side-by-Side Refrigerator
ZISB480DH
OVERALL DIMENSIONS
AFTER PANEL INSTALL
FLUSH INSET INSTALLATION
26" (66.0)
20 5/8" (52.4)
50" (127.0)
11 11/16"
(29.7)
15 3/8"
(39.1)
72 5/8"
84 1/2"
* 83 1/2"
(184.5)
(214.6)
(212.1)
68 5/8"
(174.3)
*39 17/32"
(100.4)
SPECIFICATIONS
Overall Width
50" (127.0 cm)†
Overall Height
84 1/2" (214.6 cm) †
Overall Depth
26" (66.0 cm) †
Door Clearance
28 5/8" (72.1 cm)
Cutout Width
51" (129.5 cm)
Cutout Height
85" (215.9 cm)
Cutout Depth
26 3/16" (66.5 cm)
Plumbing Requirements
1/4" OD copper
tubing or GE
SmartConnect kit
Shipping Weight
775 lb (351.5 kg)
4"
FRONT VIEW
SIDE VIEW
(10.2)
Use leveling legs and wheels for maximum 1" height
adjustment from shipping height. Nominal installation height is 84”
47" (119.4)
Case width
**13"
**20"
(33.0)
(50.8)
† Dimensions include 3/4" custom cabinet panel
28 5/8"
*115° Door swing
ATTENTION ELECTRICIAN:
(72.7)
Doors can be adjusted to
90° door swing
A 115 volt 60Hz., 15 or 20 amp power supply
is required. An individual properly grounded
branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical
receptacle recessed into the back wall.
TOP VIEW
** Allow 4" (10.2) min
clearance to a wall
for 90˚ door swing
** Allow 4" (10.2) min
clearance to a wall
for 90˚ door swing
** These refrigerators are equipped with a 2-position door stop. The factory-set 115° door
swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow
a 15" minimum clearance to wall for pan removal. If the 90° door stop position is used, pan
access is maintained, but pan removal is restricted.
Dimensions in parentheses are in centimeters unless otherwise noted.
Actual product dimensions may vary due to manufacturing tolerances.
ZISB480DH
Product Specification Revised 2/15
Monogram® 48" Built-In Side-by-Side Refrigerator
FLUSH INSET INSTALLATION 3/4" PANELS
5 1/4"
(13.3)
20"
(50.8)
6"
Finished cleats
24" (61.0)
1 1/2"
1/4"
(8.3)
5"
(12.7)
NOTES
Width of side cleats
Width between cleats
6"
75"
5"
85"
A
(56.5)
75"
(190.5 )
From floor
to bottom
of electrical
area
85"
(215.9)
5"
WARNING:
The refrigerator is top heavy and must
be secured to prevent the possibility of
tipping forward. Failure to do so may
result in death or serious injury.
22 1/4"
(190.5 ) (12.7)
From floor
to bottom
of electrical
area
Finished cleats
B Water supply area.
E
(15.2)
(215.9)
5" 3 1/2"
(12.7)
(12.7)
WATER
FRONT
3 1/2" VIEW
W
The information below is for cabinet
design only. When installing the antitip system you must use the product
installation instructions.
Determine your installation construction
and required anti-tip configuration:
C Cut a 1" x 4" block 35” long. Measure
(8.9)
3 1/2" and mark under the soffit,
7"
7"
(17.8)
B
(8.9)
(17.8)
WATER
FRONT VIEW
2" x 4"
C
Cut to 35" Length
D
FLUSH INSTALLATION
ZISB480DH
3 1/2"
SIDE(8.9)
VIEW
Anti-tip Bracket
SOFFIT
A M
ounting the junction box in this
location will also allow for front
accessibility through access panel.
1/2" (1.3)
51" (129.5) Flush inset width
49 1/2" (125.7)
3/4" (1.9)
(212.1-214.6)
*Trim will overlap
additional 7/16"
SIDE VIEW
7/16" (1.1)
Trim overlap
(3.8)
Case Trim
3/4" Panel
26 3/16" (66.5)
20 15/16" (53.2)
*83 1/2"Depth
minto cleat
*84 1/2" max
Case
3
Door
E
Flush inset depth
FLUSH INSET INSTALLATION
TOP VIEW
47 1/2" (120.7)
(15.2)
ZISB480DH
W
(8.9)
5 1/4" from the front edge of the
cabinet. Secure the wood block under
the soffit. From the bottom of the
block to the finished floor should
measure 84".
D Wooden Wall Studs and No Soffit
• Cut a 2" x 4" block and secure to
brackets provided.
• Secure brackets to back wall of
opening at 84" or your installation
height from the floor.
See Installation Instructions for
detailed instructions.
Screws mounted
into vertical wall
studs
*84"
(213.4)
*Or installation
height from floor
SIDE VIEW INSTALLED
UNDER SOFFIT
SIDE VIEW INSTALLED
WITH WOODEN WALL STUDS
AND NO SOFFIT
ZISB480DX
Product Specification Revised 2/15
Monogram® 48" Built-In Side-by-Side Refrigerator
FLUSH INSET INSTALLATION 1/2" PANELS
6"
Case
Width of side cleats
75"
Finished cleats
5"
The refrigerator is top heavy and must
be secured to prevent the possibility of
tipping forward. Failure to do so may
result in death or serious injury.
22 1/4"
(56.5)
The information below is for cabinet
design only. When installing the antitip system you must use the product
installation instructions.
75"
(190.5 )
From floor
to bottom
of electrical
area
85"
(215.9)
5"
WARNING:
A
E
(190.5 (12.7)
)
From floor
to bottom
of electrical
area
85"
B Water supply area.
Width between cleats
6"
(215.9)
A M
ounting the junction box in this
location will also allow for front
accessibility through access panel.
51" (129.5) Flush inset width
49 1/2" (125.7)
3/4" (1.9)
(15.2)
Determine your installation
construction and required anti-tip
configuration:
5" 3 1/2"
(12.7)
(12.7)
WATER
VIEW
3 FRONT
1/2"
SIDE VIEW
NOTES
1/2" (1.3)
1/2" Panel
(212.1-214.6)
*Trim will overlap
additional 7/16"
W
7/16" (1.1)
Trim overlap
(3.8)
Case Trim
5"
(12.7)
20 13/16" (52.9)
Depthmin
to cleat
*83 1/2"
*84 1/2" max
24" (61.0)
1 1/2"
3 1/4"
(8.3)
Finished cleats
Door
E
26 3/16" (66.5)
Flush inset depth
FLUSH INSET INSTALLATION
TOP VIEW
47 1/2" (120.7)
5 3/8"
(13.7)
20" (50.8)
(15.2)
ZISB480DH
(8.9)
3 1/2"C Cut a 1" x 4" block 35” long. Measure
7"
7"
(17.8)
(17.8)
B
(8.9)
3 1/2"
(8.9) VIEW
SIDE
WATER
FRONT VIEW
Anti-tip Bracket
2" x 4"
C
SOFFIT
Cut to 35" Length
D
FLUSH INSTALLATION
ZISB480DH
W
(8.9)
and mark under the soffit,
5 3/8" from the front edge of the
cabinet. Secure the wood block
under the soffit. From the bottom of
the block to the finished floor should
measure 84".
D Wooden Wall Studs and No Soffit
• Cut a 2" x 4" block and secure to
brackets provided.
• Secure brackets to back wall of
opening at 84" or your installation
height from the floor.
See Installation Instructions for
detailed instructions.
Screws mounted
into vertical wall
studs
*84"
(213.4)
*Or installation
height from floor
SIDE VIEW INSTALLED
UNDER SOFFIT
SIDE VIEW INSTALLED
WITH WOODEN WALL STUDS
AND NO SOFFIT
ZISB480DX
Product Specification Revised 2/15
Monogram® 48" Built-In Side-by-Side Refrigerator
FLUSH INSET 3/4" PANEL DIMENSIONS
A
Grille Panel
D
E
Dispenser
Cutout
FLUSH INSET INSTALLATION
PANEL DIMENSIONS
B
NOTES
A
B
C
D
E
50"
11 3/16"
68 5/8"
20 7/8"
28 7/8"
Trimmed refrigerators are designed to
be customized with decorative panels.
Field-installed 1/2" or 3/4" custom door
and grille panels are required. For 3/4"
raised door and grille panels, routing is
required. The router depth is 1/4" all the
way around the panel’s backs. Additional
panel width reductions are required per the
diagrams shown. This will create “picture
frame” routing allowing the panels to slide
into the attached door and grille trims.
F
Dispenser
Cutout
G
15 3/8"
(39.1)
DISPENSER CUTOUT
POSITION
C
F
G
17 23/32"
5 3/8"
Maximum total panel weight:
• Fresh food door panels – 75 lbs.
• Freezer drawer panel – 53 lbs.
• Grille panel – 18 lbs
9 5/8"
(24.4)
Fresh
Food
Panel
Freezer
Panel
ZISB480DH
Door Handles
Door handle not included. A custom handle
supplied by your cabinet maker may be used.
ZKHPSS1: Professional tubular stainless steel
handle designed to fit 3/4" panels. Kit includes
one handle – 30 1/2" long.
3/4" raised door PANEL Routing
DETAIL TOP
NOTE: Routed areas should be
finished as they may be visible
when assembled.
3/4"
11/32"
1/4"
1/4"
11/32"
ZKHSS2: European tubular stainless steel
handle designed to fit 3/4" panels. Kit includes
one handle – 64 1/4" long.
TOP
Front
Back
Back
3/32"
Front
CORNER VIEW SHOWING
“PICTURE FRAME” ROUTING
DETAIL BOTTOM
DETAIL HINGE
SIDE
DETAIL HANDLE
SIDE
ROUTER DEPTH 1/4"
2 1/16"
Front
HINGE
SIDE
3/16"
HANDLE
SIDE
Back
3/4" PANEL BOTTOM VIEW
(AFTER ROUTING)
BOTTOM
3/4" PANEL SIDE VIEW
(AFTER ROUTING)
Product Specification Revised 2/15
Monogram® 48" Built-In Side-by-Side Refrigerator
ZISB480DH
3/4" raised grille PANEL Routing
FLUSH INSET INSTALLATION
NOTE: Routed areas should be
finished as they may be visible
when assembled.
NOTES
TOP
DETAIL TOP
Trimmed refrigerators are designed
to be customized with decorative
panels. Field-installed 1/2" or 3/4"
custom door and grille panels are
required. For 3/4" raised door and grille
panels, routing is required. The router
depth is 1/4" all the way around the
panel’s backs. Additional panel width
reductions are required per the diagrams
shown. This will create “picture frame”
routing allowing the panels to slide into
the attached door and grille trims.
Front
Back
ROUTER DEPTH 1/4"
2"
Back
Front
Maximum total panel weight:
• F resh food door panels – 75 lbs.
• F reezer drawer panel – 53 lbs.
•G
rille panel – 18 lbs.
CORNER VIEW SHOWING
“PICTURE FRAME” ROUTING
Door Handles
Door handle not included. A custom
handle supplied by your cabinet maker
may be used.
3/16"
ZKHPSS1: Professional tubular stainless
steel handle designed to fit 3/4" panels. Kit includes one handle – 30 1/2" long.
BOTTOM
3/4" PANEL SIDE VIEW
(AFTER ROUTING)
DETAIL BOTTOM
DETAIL
LEFT SIDE
ZKHSS2: European tubular stainless steel
handle designed to fit 3/4" panels. Kit
includes one handle – 64 1/4" long.
DETAIL RIGHT
SIDE
ROUTER DEPTH 1/4"
ROUTER DEPTH 1/4"
2 1/16"
2 1/16"
Front
LEFT
SIDE
RIGHT
SIDE
Back
3/4" PANEL BOTTOM VIEW
(AFTER ROUTING)
Product Specification Revised 2/15
Monogram® 48" Built-In Side-by-Side Refrigerator
DISPENSER TRIM
A
ZISB480DH
FLUSH INSET INSTALLATION
Freezer Door
1/4" Backer Panel
.85"
Freezer Door
.10" Spacer Panel
Ice/Water Dispenser
NOTES
Total
Thickness
These refrigerators are supplied with a
dispenser trim for flush inset panels.
Ice/Water Dispenser
A
3/4" Flush Panel
1/2" Overlay Panel
3/4" OVERLAY PANEL
DISPENSER TRIM
1/2" OVERLAY PANEL
DISPENSER TRIM
P
anel Dispenser Trim:
The provided dispenser trim is designed
to fit a total panel thickness of 3/4"
or 0.85".
• If the panel is less than 3/4" thick, a
noticeable gap may be created around the
dispenser trim.
• If the panel is more than 0.85" thick, the
dispenser trim cannot be secured to
the door.
RAISED PANEL DESIGN ON DISPENSER MODELS
• T he overlay panel must be constructed
according to the specifications shown to
achieve the correct total thickness.
3/4" or 1/2" Flush Panel
•W
hen a raised panel design is to be used,
a custom middle rail is required.
16 3/4"
3/4" or .85"
B
Total
Thickness
C
Raised Panel Design on Dispenser Models:
When a raised panel design is to be used,
a custom wide middle rail is required to
accept the dispenser trim.
B
• The middle rail must be wide enough
to allow for the dispenser trim to
overlap the opening.
C
• The middle rail must be 3/4" total
thickness for 3/4" panels or 0.85" total
thickness for 1/2" panels to accept the
dispenser trim.
10 5/8"
DISPENSER TRIM
SIDE VIEW CROSS SECTION
(Showing Raised Panel with
Middle Rail)
Product Specification Revised 2/15
Monogram® 48" Built-In Side-by-Side Refrigerator
FLUSH INSET 1/2" PANEL DIMENSIONS
FLUSH INSET INSTALLATION
A
D
Dispenser
Cutout
E
F
G
A
B
C
1/4" Backer Panel
45 7/8"
9 1/2"
68 3/8"
18 9/16" 29 9/16"
.10" Space Panel
45"
8 5/8"
67"
17 9/16" 25 9/16"
1/2" Overlay Panel
50"
11 3/16"
68 5/8"
C
Dispenser
Cutout
Fresh
Food
Panel
Freezer
Panel
NOTES
PANEL DIMENSIONS
B
Grille Panel
ZISB480DH
15 3/8"
(39.1)
D
E
20 7/8"
28 7/8"
DISPENSER CUTOUT
POSITION
F
G
17 23/32"
5 3/8"
The 1/2" overlay panel must be secured to
a .10" spacer panel and a 1/4" thick backer
panel, which slides into the trim.
Assemble the panels with glue and screws:
•C
enter the spacer panel on the backer
panel, left to right and top to bottom.
Secure the panels with glue.
•R
efer to the chart for locating the backer
panel to the overlay panel. Secure the
overlay panel to the backer panel with glue
and screws. Screws must be countersunk
into the backer panel.
Maximum total panel weight:
• F resh food door panel – 75 lbs.
• F reezer drawer panel – 53 lbs.
•G
rille panel – 18 lbs.
9 5/8"
(24.4)
1/4" backer assembly routing dimensions
Hinge Side
C
C
Door
1/2"
Overlay
Panel
Backer with
Overlay Panel
Assembly
1/4"
Backer
Panel
Fresh Food
Back
Freezer
Back
D
.10"
Spacer
D
A
B
A
B
PANEL DIMENSIONS
C
A
B
C
D
Fresh Food Panel
2 1/16"
1/16"
1/8"
1/8"
Freezer Panel
2 1/16"
1/16"
1/8"
1/8"
Grille Panel
2 1/16"
2 1/16"
1 15/32"
7/32"
A
Grille Back
D
B
Product Specification Revised 2/15
Monogram® 48" Built-In Side-by-Side Refrigerator
ZISB480DH
OVERALL DIMENSIONS
STANDARD INSTALLATION
25 1/2" (64.8)
25 1/2" (64.8)
23 7/8" (60.7)
23 7/8" (60.7)
48" (121.9)
48" (121.9)
1 3/4"
1 3/4"
(4.4)
(4.4)
13 1/2"
13 1/2"
(34.3)
(34.3)
*84"
*83 1/2"
*83(212.1)
1/2"
*84"
(213.4)
(213.4)
(212.1)
68 1/2"
68 (174.0)
1/2"
(174.0)
*72 1/4"
*72(183.5)
1/4"
(183.5)
*40"
*40"
(101.6)
(101.6)
SPECIFICATIONS
Overall Width
48" (121.92 cm)
Overall Height
84" (213.36 cm)
Overall Depth
25 3/8" (64.453 cm)
Door Clearance
28 5/8" (72.1 cm)
Cutout Width
47 1/2" (120.7 cm)
Cutout Height
83 1/2" - 84 1/2"
(212.1 - 214.6 cm)
Cutout Depth
24" (61 cm)
Plumbing Requirements
1/4" OD copper
tubing or GE
SmartConnect kit
Shipping Weight
775 lb
*3 3/4"
*3 3/4"
(9.5)
(9.5)
FRONT VIEW
FRONT VIEW
*3 1/2"
*3 1/2"
(8.9)
* Shipping height. Use leveling legs and wheels for maximum
* Shipping
Use leveling
legs andheight.
wheels for maximum
1" heightheight.
adjustment
from shipping
1" height adjustment from shipping height.
(8.9)
SIDE VIEW
SIDE VIEW
47" (119.4)
47"
(119.4)
Case
width
Case width
** Allow 15" (38.1) min
** Allow
15" (38.1)
min
clearance
for 130˚
clearance
for 130˚
door swing
door swing
** Allow 20" (50.8) min
** Allow
20" (50.8)
min
clearance
for 130˚
clearance
for 130˚
door swing
door swing
ATTENTION ELECTRICIAN:
26 5/8"
26 5/8"
(67.6)
A 115 volt 60Hz., 15 or 20 amp power supply
is required. An individual properly grounded
branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical
receptacle recessed into the back wall.
(67.6)
TOP VIEW
TOP VIEW
** Allow 4" (10.2) min
**clearance
Allow 4"to(10.2)
min
a wall
for 90˚
clearancedoor
to a swing
wall for 90˚
door swing
** Allow 4" (10.2) min
**clearance
Allow 4"to(10.2)
min
a wall
for 90˚
clearancedoor
to a swing
wall for 90˚
door swing
** These refrigerators are equipped with a 2-position door stop. The factory-set 130° door
** These
are equipped
with a 2-position
door stop.
Theor
factory-set
130° doorAllow
swingrefrigerators
can be adjusted
to 90° if clearances
to adjacent
cabinets
walls is restricted.
swing
can
be
adjusted
to
90°
if
clearances
to
adjacent
cabinets
or
walls
is
restricted.
Allow
full 130° door swings for pan removal. If the 90° door stop position is used, pan access
is
full
130° door swings
pan removal.
If the 90° door stop position is used, pan access is
maintained,
but panfor
removal
is restricted.
maintained, but pan removal is restricted.
Dimensions in parentheses are in centimeters unless otherwise noted.
Actual product dimensions may vary due ZISB480DX
to manufacturing tolerances.
ZISB480DX
Product Specification Revised 2/15
Monogram® 48" Built-In Side-by-Side Refrigerator
ZISB480DH
STANDARD INSTALLATION
STANDARD INSTALLATION
TOP VIEW 24" (61.0)
3 1/4"
(8.3)
1 1/2"
47 1/2" (120.7)
20" (50.8)
6"
24" (61)(15.2)
3 1/8"
(7.93)
1 9/16"
E
A M
ounting the junction
box in this location will
also allow for front
accessibility through
access panel.
47 1/2" (120.7)
20" (50.8)
A
7/16" (1.1)
Trim overlap
5"
(3.97)
NOTES
7/16" (1.1)
Trim overlap
(3.8)
(12.7)
6"
*83 1/2" min
*84 1/2" max
E
(15.24)
(212.1-214.6)
*Trim will overlap
additional 7/16"
B Water supply area.
5"
WARNING:
(12.7)
The refrigerator is top
heavy and must be secured
to prevent the possibility of
tipping forward. Failure to
do so may result in death
or serious injury.
75"
(190.5 )
From floor
to bottom
*84 1/2" of electrical
area
(214.6)
*Trim will overlap
additional 7/16"
5"
75"
(190.5 )
From floor
to bottom
of electrical
area
5" 3 1/2"
(12.7)
(12.7)
(8.9)
5"
(12.7)
WATER
3 1/2"
5"
(12.7)
B
(8.9)
FRONT
VIEW
W
SIDE VIEW
WATER
FRONT VIEW
SIDE VIEW
3 1/2"
(8.9)
The refrigerator
will project
forward, slightly
beyond adjacent
cabinetry.
3 1/2"
W (8.9)
Anti-tip Bracket
2" x 4"
C
SOFFIT
Cut to 35" Length
D
E
*84"
(213.4)
STANDARD INSTALLATION
*Or installation
height from floor
ZISB480DH
3/4"
Min.
Top Case Trim
Side View Top
Case Trim
Install Screws
Through Trim and Into
3/4" Min. Wood Brace
SIDE VIEW INSTALLED
WITH WOODEN WALL STUDS
AND NO SOFFIT
ZISB480DX
Determine your installation
construction and required
anti-tip configuration:
C Installed Under Soffit
After installing unit into
installation opening,
raise grille panel and
screw metal case sides to
adjacent cabinet. When
installed under a soffit, the
soffit cannot exceed 24"
deep. The top case trim
overlaps the bottom of
the soffit.
D W
ooden Wall Studs and
No Soffit
• Cut a 2" x 4" block and
secure to brackets
provided.
• Secure brackets to back
wall of opening at 84" or
your installation height
from the floor.
Screws mounted
into vertical wall
studs
SIDE VIEW INSTALLED
UNDER SOFFIT
The information below is
for cabinet design only.
When installing the antitip system you must use
the product installation
instructions.
FRONT VIEW INSTALLED
WITH METAL WALL STUDS
AND NO SOFFIT
E M
etal Wall Studs and
No Soffit
This method requires
securely fastened cabinets
on both sides and a 3/4"
minimum wood brace
above unit, with it’s front
surface 24" from back wall.
• After installing unit into
opening, raise grille panel
and attach metal case
top trim to 3/4" minimum
wood brace.
• The brace spanning
the enclosure must be
securely fastened to
cabinets on both sides.
See Installation
Instructions for detailed
instructions.
Product Specification Revised 2/15
Monogram® 48" Built-In Side-by-Side Refrigerator
CUSTOM SIDE PANELS
ZISB480DH
STANDARD INSTALLATION
F
24" (61.0)
NOTES
3/16"
(.5)
1 7/8"
(4.8)
*84”
*84"
(213.4)
*Depending
on installation
height
F S
ide panels must be
used whenever the sides
of the refrigerator will
be exposed. The 1/4"
side panels will slip
into the side case trim.
Secure the panels to
the refrigerator with
stick-on hook and loop
fastener strips. Order
the side panels from the
cabinet manufacturer.
*3" - 4"
(7.6 - 10.2)
*Depending
on installation
height
2 9/16"
(6.5)
XRH _ZIFP360NXLH_ZIFP360NXRH_ ZIFS360NXLH_ZIFS360NXRH
XRH_ZIRP360NXLH_ZIRP360NXRH_ZIRS360NXLH_ZIRS360NXRH
Product Specification Revised 2/15
Monogram® 48" Built-In Side-by-Side Refrigerator
ZISB480DH
1/4" FRAMED PANEL DIMENSIONS
STANDARD INSTALLATION
NOTES
PANEL ASSEMBLY CROSS SECTION
A
D
Trim
B
Grille Panel
Trimmed refrigerators are designed to
be customized with decorative panels.
Field-installed custom door and grille
panels are required.
Door
E
1/4" Framed Panel
Supplied Handles
Dispenser F
Cutout
PANEL DIMENSIONS
G
C
Fresh
Food
Panel
Freezer
Panel
1/4" Framed Panel
Dispenser
Cutout
A
B
C
45 7/8"
9 1/2"
68 3/8"
D
E
18 9/16" 26 9/16"
1/4" Framed Panels:
For 1/4" thick custom panels ordered from
your cabinet maker; the decorative panels
slide into the trim.
Maximum total panel weight:
• Fresh food door panel – 75 lbs.
• Freezer drawer panel – 53 lbs.
• Grille panel – 18 lbs
DISPENSER CUTOUT
POSITION
15 3/8"
(39.1)
F
G
17 13/16"
5 1/8"
9 5/8"
(24.4)
3/4" Overlay Panels:
For 3/4" thick custom panels ordered from
your cabinet maker; the decorative panels
slide into the trim.
3/4" OVERLAY PANEL DIMENSIONS
PANEL ASSEMBLY CROSS SECTION
A
B
Grille Panel
D
Dispenser
Cutout
The overlay panel must be secured to a
1/4"-thick backer panel which slides into
the trim. A spacer panel 0.10" thick must
be placed between the overlay and backer
panels.
E
Trim
Door
1/4" Backer Panel
Center each panel over the other. Assemble
the panels with glue and screws. Screws
must be countersunk into the backer panel.
3/4" Overlay Panel
.10" Spacer Panel
F
NOTE: Left-to-right offset is not always equal
to top-to-bottom offset.
Supplied Handles
PANEL DIMENSIONS
G
Freezer
Panel
C
Fresh
Food
Panel
A
B
C
1/4" Backer Panel
45 7/8"
9 1/2"
68 3/8"
.10" Spacer Panel
45"
8 5/8"
67"
3/4" Overlay Panel
46 1/8"
9 3/4"
D
E
18 9/16" 26 9/16"
17 1/4"
25 1/4"
68 5/8" 18 13/16" 26 13/16"
.25" + .10" + .75" = 1.10" Total Panel Thickness
Dispenser
Cutout
9 5/8"
(24.4)
15 3/8"
(39.1)
*DISPENSER CUTOUT
POSITION
F
G
17 15/16"
5 1/4"
Maximum total panel weight:
• Fresh food door panel – 75 lbs.
• Freezer drawer panel – 53 lbs.
• Grille panel – 18 lbs
Door Handles:
The supplied handles can be adjusted to
accommodate both framed or overlay panels.
Custom handles of your choice, supplied by
your cabinet maker, can also be installed.
ZKHPSS1: Professional tubular stainless steel
handle designed to fit 3/4" overlay panels.
ZKHSS2: European tubular stainless steel
handle designed to fit 3/4" overlay panels.
Kits include one handle. Order 2 kits for
side-by-side refrigerators from your
Monogram supplier.
* Cut the dispenser opening after the backer, spacer
and overlay panels have been assembled.
Product Specification Revised 2/15
Monogram® 48" Built-In Side-by-Side Refrigerator
DISPENSER TRIM
1/4" Framed Panel
ZISB480DH
STANDARD INSTALLATION
Freezer Door
1/4"
Total
Thickness
1.10"
Freezer Door
1/4" Backer Panel
Total
Thickness
.10" Spacer Panel
Ice/Water Dispenser
Ice/Water Dispenser
3/4" Overlay Panel
1/4" PANEL DISPENSER TRIM
3/4" OVERLAY PANEL DISPENSER TRIM
A
B
NOTES
These refrigerators are supplied with two
dispenser trims, one for framed panels
and one for overlay panels.
1/4" Panel Dispenser Trim:
The framed panel must be 1/4" nominal
thickness to fit the dispenser trim.
• The dispenser trim fits over the custom
panel and snaps into the freezer door.
• If the panel is less than 0.250" thick, a
noticeable gap may be created around
the dispenser trim. Foam tape may be
applied on the door to improve the fit.
RAISED OVERLAY PANEL DESIGN ON DISPENSER MODELS
• If the panel is more than 0.250" thick,
the dispenser trim cannot be secured
to the door.
1/4" Backer Panel
.10" Spacer
3/4" Overlay Panel
3/4" Overlay Panel Dispenser Trim:
The 3/4" overlay dispenser trim is
designed to fit a total panel thickness
of 1.100".
16 3/4"
1.10”
C
Total
Thickness
D
• If the panel is less than 1.100" thick, a
noticeable gap may be created around
the dispenser trim.
• If the panel is more than 1.100" thick,
the dispenser trim cannot be secured
to the door.
10 5/8"
DISPENSER TRIM
• The overlay panel must be constructed
according to the specifications shown
to achieve the correct total thickness.
SIDE VIEW CROSS SECTION
(Showing Raised Overlay
with Middle Rail)
• A
lternative panel construction methods
such as securing a 3/4" panel to a 1/4"
backer panel cannot be used. Another
method, routing a 3/4"-thick panel
on all sides, cannot be used. These
methods will not result in the required
1.100" panel thickness.
• When a raised panel design is to be
used, a custom middle rail is required.
Raised Overlay Panel Design on
Dispenser Models:
When a raised panel design is to be used,
a custom wide middle rail is required to
accept the dispenser trim.
• The middle rail must be wide enough to
allow for the dispenser trim to overlap
the opening.
• The middle rail must be 1.10" total
thickness to accept the dispenser trim.
Product Specification Revised 2/15
Monogram® 48" Built-In Side-by-Side Refrigerator
ZISB480DH
FEATURES AND BENEFITS
Halogen Light Columns - Located in the freezer
and fresh food compartments, extend the full
length of the interior compartments providing
brilliant, all-level illumination
LED Lighting - Located at the top of the fresh
food compartment, and inside the vegetable and
climate-control drawers, illuminates contents
without compromising space
Advanced Temperature Management System
with Multi-Shelf Air Tower - Provides even
distribution of air throughout the refrigerator
Climate-Control Drawer - Allows you to expresschill beverages, express-thaw meats and select
specific temperatures for perishable foods
Dispenser with Proximity Sensor - Designed
to accommodate glassware of all sizes, from
pitchers to tumblers; control graphics light up as
you approach and automatically switch off when
you walk away
Dairy Bin with Center Divider - Has a unique
magnetic seal that locks in freshness
Filter-Change Indicator Light - Located on the
upfront control panel, provides a visual reminder
when it's time to replace the filter for the water
dispenser
GE® Water Filter - Has been moved from the
fresh food compartment to the overhead cabinet,
where it is discreetly out of sight
Drop-Down Shelf - Provides additional space
for a casserole dish or pizza box
R
Product Specification Revised 2/15