Assembly Instructions
Important
Before you begin, please make sure all parts and proper quantities
are included. Any parts damaged during shipment must be reported
within 15 days of receipt. To report information regarding damage, to
purchase parts or accessories, or if you have any questions, please
contact us at:
www.spectrumfurniture.com
715-723-6750, 800-235-1262
Thank you for purchasing Spectrum products!
(1) 0112504
shelf bracket
(1) 0112503
12”W x 8-1/2”D shelf
(1) 0112502
6-1/2”W x 8-1/2”D shelf
(4) 026059
1/4” washer
(6) 041943
1/4-20 locknut
(4) 059534
1/4-20 x 30mm
JC bolt
(1) 025039
4mm hex wrench
While the camera mount can be installed below the monitor
with the monitor still installed, Spectrum recommends the
monitor be temporary lifted off the monitor mount to simplify
installation and prevent monitor damage.
Tools Required
Camera Mount
37108
4mm hex wrench
(included)
7/16” or adjustable
wrench
masking tape
electric drill
with 3/8” drill bit
Assemble camera mount
1. Choose one shelf (large or small) that fits your specific camera.
2. Attach the bracket to the shelf as shown with (2) 1/4-20 locknuts and
tighten securely. Figure 1.
Note: The camera mount comes with
two different shelf sizes to accommodate
multiple camera and video devices.
shelf bracket
1/4-20 locknut
(2 required)
large or small shelf
• Proceed to p.2 to install to an InVision Access display stand.
• Proceed to p.4 to install to an InVision Media Collaboration display stand.
Figure 1
0112774R1 Page 1 of 6
InVision Access™ Collaboration Table installation
Installation
1. Using two people, carefully lift the monitor off the monitor mount and set aside.
2. Remove the display stand back panel. Figure 2.
3. The monitor mount needs to be in the lower position to install the camera
mount. If the mount is in the upper position, remove the mounting hardware
and re-attach using the lower set of mounting holes. Figure 3.
InVision Access table
with Display Stand
37120
display stand
back panel
(4) 1/4-20 x 15mm
JC bolts
Figure 2
display stand
monitor mount
use lower set
of (6) holes for
monitor mount
Figure 3
0112774R1 Page 2 of 6
4. Locate the four 3/8” holes on top of the display stand front panel.
These holes do not go all the way through the panel so they will need
to be drilled completely through.
5. Apply masking tape over the hole locations on the mount-side of the
panel to minimize laminate chip-out while drilling.
6. Using a drill with a sharp 3/8” drill bit, slowly drill through the panel at
the four 3/8” hole locations. Figure 4.
apply masking tape over the
hole locations on this side
of the display stand panel to
prevent laminate chip-out
(4) 3/8” holes in panel
(drill through)
drill with
3/8” drill bit
display stand
front panel
Figure 4
assembled
camera mount
7. Align the assembled camera mount as shown and attach to the
display stand with (4) 1/4-20 x 30mm JC bolts, (4) 1/4” washers,
and (4) 1/4-20 locknuts. Figure 5. Do not tighten completely.
Adjust the camera mount to tallest height before tightening.
8. Carefully replace the monitor back onto the monitor mount.
9. Adjust the camera mount to sit just above the installed monitor
then tighten the bolts securely.
10.Install your camera on the shelf and route cords down behind the
monitor and through the display stand front panel grommets.
11.After all electrical connections and wiring is complete, re-install the
back panel with (4) 1/4-20 x 15mm JC bolts and tighten securely.
(4) 1/4-20 x
30mm JC bolt
(4) 1/4” washer
(4) 1/4-20 locknut
Figure 5
0112774R1 Page 3 of 6
InVision™ Media Collaboration Table installation
Note: On InVision collaboration tables, (non-Access) the mount can be located in 2 different positions:
above the monitor for group teleconferencing, or below the monitor for face-to-face conferencing.
Installation below monitor
1. Using two people, carefully lift the monitor off the monitor mount and set aside.
2. Remove the display stand back panel by removing the (6) 1/4-20 x 30mm JC bolts (retain bolts)
and set aside. Figure 2.
3. Locate the two 3/8” holes in the display stand front panel. These holes do not go all the way
through the panel so they will need to be drilled completely through.
4. Apply masking tape over the hole locations on the mount-side of the panel to minimize laminate
chip-out while drilling.
5. Using a drill with a sharp 3/8” drill bit, slowly drill through the panel at the two 3/8” hole locations.
Figure 3.
6. Orient the assembled camera mount as shown with the display stand front panel. Using the center
slot, align the shelf bracket with the two centered mounting holes and install (2) 1/4-20 x 30mm JC
bolts with (2) 1/4-20 locknuts (not shown) and (2) 1/4 washers (not shown) on the back. Figure 4.
7. Carefully lift the monitor back onto the monitor mount.
8. Adjust the camera mount to sit below the installed monitor with enough clearance for your
camera, then tighten the bolts securely. Figure 5.
9. Install camera onto the shelf.
10.Route cords through the display stand front panel grommets.
11.After all electrical connections and wiring is complete, re-install the back panel with the (6) 1/4-20
x 30mm JC bolts and tighten securely.
monitor
mount
display stand
back panel
InVision table
with Display Stand
37106
display stand
front panel
(2) 3/8” holes
in panel
1/4-20 x 30mm
JC bolt
drill with
3/8” drill bit
Figure 2
Figure 3
monitor
display stand
front panel
(2) 1/4-20 x 30mm
JC bolts with (2) 1/4
washers and
(2) 1/4-20 locknuts
on back
Figure 4
adjust shelf
below monitor
camera
mount
assembled
camera mount
Figure 5
0112774R1 Page 4 of 6
Installation above monitor
1. Using two people, carefully lift the monitor off the monitor mount and set aside.
2. Remove the display stand back panel by removing the (6) 1/4-20 x 30mm JC bolts (retain these
bolts) and set aside. Figure 6.
3. Remove the screws attaching the angle filler to the back panel. Figure 7A.
4. Flip the angle around and re-attach to the panel with the cutout side facing up as shown. Figure 7B.
5. Locate the four 3/8” holes on top of the display stand front panel. These holes do not go all the
way through the panel so they will need to be drilled out. Figure 8.
6. Apply masking tape over the hole locations on the mount-side of the panel to minimize laminate
chip-out while drilling.
7. Using a drill with a sharp 3/8” drill bit, slowly drill through the display stand panel at the four 3/8”
hole locations. Figure 8.
monitor
mount
InVision table
with Display Stand
37106
display stand
back panel
1/4-20 x 30mm
JC bolt
apply masking tape over
the hole locations on
this side of the display
stand panel to prevent
laminate chip-out
(4) 3/8” holes
in panel
drill with
3/8” drill bit
Figure 6
angle filler with
solid side facing up
(for below-monitor
installation)
angle filler flipped with
cutout side facing up
(for above-monitor
installation)
display stand
front panel
remove
screws
Figure 7A
Figure 8
re-attach with
screws
display stand
back panel
Figure 7B
display stand
back panel
0112774R1 Page 5 of 6
8. Align the assembled camera mount as shown in Figure 9.
9. Using the outer slots, attach the camera mount to the back side of
the display stand front panel with (4) 1/4-20 x 30mm JC bolts, (4)
1/4 washers, and (4) 1/4-20 locknuts. Do not tighten completely.
10.Carefully replace the monitor back onto the monitor mount.
assembled
camera mount
1/4-20 x 30mm JC bolts
(4 required)
1/4 washers
(4 required)
1/4-20 locknuts
(4 required)
monitor mount
display stand
front panel
Figure 9
camera mount
11.Adjust the camera mount to sit just above the installed monitor then
tighten the shelf fasteners securely. Figure 10.
12.Install your camera on the shelf and route cords down behind the
monitor and through the display stand front panel grommets.
13.After all electrical connections are made, re-attach the display stand
back panel with the (6) previously removed 1/4-20 x 30mm JC bolts
and tighten securely. Figure 11.
camera
mount
adjust shelf just
above monitor
monitor
display stand
back panel
Figure 10
1/4-20 x 30mm
JC bolt
Figure 11
925 First Avenue, PO Box 400, Chippewa Falls, WI 54729 Ph: 800-235-1262, 715-723-6750 Fax: 800-335-0473, 715-738-2309
E-mail: spectrum@spectrumfurniture.com
web: www.spectrumfurniture.com
0112774R1 Page 6 of 6