Issue: 01 Date: 2008-09-04 Specification AXIOM260 Oscillator type : OCXO with Low Phase Noise under Vibration Parameter Nominal frequency Frequency stability Initial tolerance at delivery vs. temperature in operating temperature range vs. supply voltage variation vs. load change Long term (aging) per day Long term (aging) 1st year Long term (aging) over 10 years Frequency adjustment range Electronic Frequency Control (EFC) EFC voltage VC EFC tuning sensitivity EFC slope (∆f / ∆VC) EFC input impedance RF output Signal waveform Load RL Output level @ VC = 0 V @ VC = ± 4 V @ VC = ± 4 V Output VSWR Harmonics Spurious min. ± 1.6 -4.0 0 0.75 positive Condition MHz @VC = 0 V ±1 ± 2.0 ± 3.0 ± 10 ± 10 ± 10 ± 100 ± 1.5 ppm ppm ppm ppb ppb ppb/day ppb ppm @+25°C @VC = 0 V -30°C~+71°C -40°C~+85°C VS ± 2% RL ± 10% +4.0 ppm V ppm/V + 6.0 +5.5 +5.0 kΩ Sine wave 50 +7 +8.0 +7 +8.5 +7 +9.0 1.5 -30 -80 -100 -120 -110 80 14.25 -85 -115 -145 -145 -165 -168 -168 -55 -55 -125 -145 -155 -165 -168 15 Current consumption (warm-up) Wasemweg 5 D-74821 Mosbach Germany Unit 10 Phase noise under vibration (vibration spectrum see table III) GmbH & Co. KG max. 120.000 Power Supply Ripple Rejection (10 mVp-p) Warm-up time Phase noise in quiet state Supply voltage VS Current consumption (steady state) typ. AXIOM260 page 1(3) 15.75 400 300 150 100 550 Ω dBm dBm dBm dBc dBc dBc dBc dBc sec dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz V mA mA mA mA mA Note 2 Note 2 Note 3 Note 4 100 Hz ~ 1 kHz 1 kHz ~ 10 kHz 10 kHz ~ 20 MHz DC to 2 MHz to full performance @ 10 Hz @ 100 Hz @ 1kHz @ 2 kHz @ 10 kHz @ 50 kHz @ 100 kHz @ 10 Hz @ 100 Hz @ 1kHz @ 2 kHz @ 10 kHz @ 50 kHz @ 100 kHz @ -40°C @ 0°C @ +25°C @ +85°C www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: info@axtal.com Parameter Operating temperature range Operable temperature range Storage temperature range Enclosure Weight Finish Solder pins min. max. Unit -40 +85 -45 +90 -55 +105 58.25 x 48.27 x 22.75 75 MIL-F-14072 type I RF: 0.8 mm diameter, Others: 1.0 mm diameter typ. °C °C °C mm gram Condition see drawing Including shock absorbers Or equivalent tin-plated Notes: 1. Terminology and test conditions are according to IEC standard IEC60679-1 and MIL-PRF-55310, unless otherwise stated 2. from any temperature in the range -30°C to +71°C 3. from any temperature in the range -40°C to +85°C 4. at 120 MHz ± 2.5 MHz @ +25°C Enclosure drawings GmbH & Co. KG Wasemweg 5 D-74821 Mosbach Germany AXIOM260 page 2(3) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: info@axtal.com Pin connections Pin # Symbol 1 RF OUT 2 GND 3 VC 5 VS Function RF Output Ground, case Control Voltage (EFC) Supply Voltage Table 2: pin connections Environmental conditions Test Reference Altitude Vibration, random MIL-PRF55310 Acceleration, linear Acceleration, angular Moisture Resistance Salt spray Fungus EMI Endurance tests (ageing) MIL-STD-810 MIL-STD-454 MIL-STD-461B MIL-STD-462 MIL-PRF55310 Test conditions Sea level to 55000 feet 15 Hz 0.06 g²/Hz 300 Hz 0.2 g²/Hz 1000 Hz 0.2 g²/Hz 2000 Hz 0.06 g²/Hz All three axes 40g for 60 sec 9000 dec/sec² @ 25 Hz along spinning axis Up to 85 % RH, including condensation, operating and non-operating Procedure 1, method 509.1 Requirement 4 Part 1 CE03;CS01; CS02; RE02; RS03 30 days operation @25°C Table 3: Environmental conditions GmbH & Co. KG Wasemweg 5 D-74821 Mosbach Germany AXIOM260 page 3(3) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: info@axtal.com