PS Audio Power Port™ Installation Instructions PS Audio Power Port™ Installation Instructions CAUTION: To prevent severe shock or electrocution, turn the power OFF at the service panel before working with electrical wiring. CAUTION: To prevent severe shock or electrocution, turn the power OFF at the service panel before working with electrical wiring. For installation by a qualified electrician in accordance with national and local electrical codes. For installation by a qualified electrician in accordance with national and local electrical codes. Installation Installation 1. Ensure the power to the receptacle is OFF at the main panel. At the service panel switch off the breaker or remove the fuse associated with the receptacle. 2a. Wiring procedure for a single receptacle: • Connect the white wire to the neutral terminal (labeled WHITE). Tighten silver screw. • Connect the black wire to the hot terminal (labeled BLACK). Tighten brass screw. • Connect the bare wire or green cable to the ground terminal (green screw) by wrapping the exposed copper wire clockwise around the ground terminal. Tighten green screw. 2b. Wiring procedure for a series of receptacles: • In addition to the steps above, connect the additional set of neutral and hot wires to the 2nd set of terminals on the back of the Power Port. Tighten screws. 3. Screw the receptacle to the box and re-attach the faceplate. 1. Ensure the power to the receptacle is OFF at the main panel. At the service panel switch off the breaker or remove the fuse associated with the receptacle. 2a. Wiring procedure for a single receptacle: • Connect the line cable wire to the neutral terminal (labeled WHITE). Tighten screw. • Connect the line cable wire to the hot terminal (labeled BLACK). Tighten screw. • Connect the green or bare wire cable to the ground terminal (green screw) by wrapping the exposed copper wire clockwise around the ground terminal. Tighten screw. 2b. Wiring procedure for a series of receptacles: • In addition to the steps above, connect the additional set of neutral and hot wires to the 2nd set of terminals on the back of the Power Port. Tighten screws. 3. Screw the receptacle to the box and re-attach the faceplate. Note Note • Do not use aluminium wires to connect the Power Port. • The Power Port uses the back-wire method for the hot and neutral terminals. To install, strip wire approximately 0.6 in (13.5mm). Ensure the terminal screw is loosened and insert stripped wire fully into the terminal hole. Tighten screw. • The Classic Power Port (grey color) is an isolated ground device. If installed into a metal junction box with no ground wire it must be grounded for safety. • Do not use aluminium wires to connect the Power Port. • The Power Port uses the back-wire method for the hot and neutral terminals. To install, strip wire approximately 0.6 in (13.5mm). Ensure the terminal screw is loosened and insert stripped wire fully into the terminal hole. Tighten screw. • The Classic Power Port (grey color) is an isolated ground device. If installed into a metal junction box with no ground wire it must be grounded for safety. • Terminal capacity: • Terminal capacity: 15 Amp: 14-10 AWG 20 Amp: 12-10 AWG PS Audio International www.psaudio.com 720.406.8946 15 Amp: 14-10 AWG 20 Amp: 12-10 AWG PS Audio International www.psaudio.com 720.406.8946 PS Audio Power Port™ Installation Instructions PS Audio Power Port™ Installation Instructions CAUTION: To prevent severe shock or electrocution, turn the power OFF at the service panel before working with electrical wiring. CAUTION: To prevent severe shock or electrocution, turn the power OFF at the service panel before working with electrical wiring. For installation by a qualified electrician in accordance with national and local electrical codes. For installation by a qualified electrician in accordance with national and local electrical codes. Installation Installation 1. Ensure the power to the receptacle is OFF at the main panel. At the service panel switch off the breaker or remove the fuse associated with the receptacle. 2a. Wiring procedure for a single receptacle: • Connect the white wire to the neutral terminal (labeled WHITE). Tighten silver screw. • Connect the black wire to the hot terminal (labeled BLACK). Tighten brass screw. • Connect the bare wire or green cable to the ground terminal (green screw) by wrapping the exposed copper wire clockwise around the ground terminal. Tighten green screw. 2b. Wiring procedure for a series of receptacles: • In addition to the steps above, connect the additional set of neutral and hot wires to the 2nd set of terminals on the back of the Power Port. Tighten screws. 3. Screw the receptacle to the box and re-attach the faceplate. 1. Ensure the power to the receptacle is OFF at the main panel. At the service panel switch off the breaker or remove the fuse associated with the receptacle. 2a. Wiring procedure for a single receptacle: • Connect the line cable wire to the neutral terminal (labeled WHITE). Tighten screw. • Connect the line cable wire to the hot terminal (labeled BLACK). Tighten screw. • Connect the green or bare wire cable to the ground terminal (green screw) by wrapping the exposed copper wire clockwise around the ground terminal. Tighten screw. 2b. Wiring procedure for a series of receptacles: • In addition to the steps above, connect the additional set of neutral and hot wires to the 2nd set of terminals on the back of the Power Port. Tighten screws. 3. Screw the receptacle to the box and re-attach the faceplate. Note Note • Do not use aluminium wires to connect the Power Port. • The Power Port uses the back-wire method for the hot and neutral terminals. To install, strip wire approximately 0.6 in (13.5mm). Ensure the terminal screw is loosened and insert stripped wire fully into the terminal hole. Tighten screw. • The Classic Power Port (grey color) is an isolated ground device. If installed into a metal junction box with no ground wire it must be grounded for safety. • Do not use aluminium wires to connect the Power Port. • The Power Port uses the back-wire method for the hot and neutral terminals. To install, strip wire approximately 0.6 in (13.5mm). Ensure the terminal screw is loosened and insert stripped wire fully into the terminal hole. Tighten screw. • The Classic Power Port (grey color) is an isolated ground device. If installed into a metal junction box with no ground wire it must be grounded for safety. • Terminal capacity: • Terminal capacity: 15 Amp: 14-10 AWG 20 Amp: 12-10 AWG PS Audio International www.psaudio.com 720.406.8946 15 Amp: 14-10 AWG 20 Amp: 12-10 AWG PS Audio International www.psaudio.com 720.406.8946