1.)
Description of Articles (with full
Quantity required
specifications giving)
One
pH meter
• Micro processor based with high
performance digital circuit and CPU
• Multi-point push-button calibration
• Auto-buffer recognition
• Viewing of electrolyte slope and
offset value
• Automatic temperature compensation
• Large custom LCD display
• Supplied with pH electrode with
holder, pH buffers, power adapters
• pH range- 1-14 with accuracy of
±0.05pH
• resolution of 0.01pH
• Light weight
2)
Description of Articles (with full
specifications giving)
Quantity required
10 KVA UPS online 1 hr.
backup-
One
Specification: –
ACINPUT
PARAMETERS
AC Input Voltage
a-230 V-20%-15%
Single Phase or any Voltage range
as per Customer Requirement
Frequency
a-50Hz ± 10 %
Generators.
Can also Work on Good Quality
a-Out Voltage
220/230 V AC Single Phase
b-Voltage Regulation
ACOUNT
PARAMETERS
± 1%
c-Frequency
50Hz ±0.05 Hz ( Crystal Controlled )
d-Waveform
Sine wave
e-Harmonic Distortion
Less than 3 %
f-Efficiency
> 92 % for 180 V DC
> 85 % for 48 V DC/72V DC 87 %
g- Power Factor
0.8 Lagging
h-Overload
5 Cycles.
110% for 10 minute. 200 %
for
i- Crest Factor
>4:1
j-Transient Recovery
Within 3 Cycles.
An Electronics Circuit with Digital Logics Continuously Searches
for the following Faults &Trips the system with Audio – visual
Indication
PROTECTIONS
a- Battery over Voltage
b-Battery Under Voltage
c- Output AC Over Voltage b-Output Overload /short Circuit
INDICATIONS
• Main On
• Load On Battery
• Battery Low
• Inverter Over load
• Load On Main
• Battery Boost
• Battery Level Graph
• Load Level Graph
Digital metering available for Output Voltage / Battery
Voltage /Output Current /Output Frequency ( Customised
metering Option Available )
METERING
AMBIENT
CONDITIONS
a-Operating -0ºC-50 ºC
c-Relative Humidity -95% RH
b-Storage -0ºC-60ºC
d-Operating Altitudeup to 2000 meters
e-Audible Noise
Less than 55 db at 1
meter up to 10 KVA
Less than 60 db at 1
meter above 10 KVA
•
•
Static Bypass
Switch
SNMP
Interface
•
•
Remote
On/Off Panel
Hot Standby
Mode
•
Remote Indicator Panel
•
Parallel Redundant Mode
3)
PH Meter
1 Nos
Specification:Microprocessor based with high performance digital circuit and CPU
•
•
•
•
•
•
Multi – point push button calibration
Auto –buffer recognition
Viewing of electrode slope and offset value.
Automatic temperature compensation
Large custom LDC display
Supplied with pH electrode with holder, pH buffers, power
adapters , pH range 0.00~14.00pH; pH Accuracy ±0.05;pH
Resolutions 0.01; pH mV Range 0 ~±1999mV ; accuracy ± 2
mV ; pH Calibration Points 2 points; Temp. Compensation
0~100ºC ( manual );
Power Source DC9V, AC 220V (50Hz);
Dimension 210x205x65(mm);Weight 1.5kg.
4)
Hp Laser jet pro-M1136Multifunction Laser printer
Specification
Printing Method :-
Laser
Type: -
Multifunction
Display:-
Dual Digital Numeric LED
Model No: -
M1136
Model Serial:-
Laser Jet Pro
Part no.:-
CE849A
Printing Output:-
Monochrome
Printer Language:-
Hot Based
Function :-
Print, Copy, Scan
Internal Memory:-
8 GB , Brand HP
5)
Liquid Nitrogen Capacity (Litr)
GP3-3.15
1 Nos.
6)
Refrigerator
Specification:-Capacity: 350 Litters.
-Two Doors.
-Frost Free
-Air booster system
-Large (34L) and separate drawer
-6th sense electronic control.
1 No.
1 No.
7) Vertical gel electrophoresis apparatus.
1No.
Specification:1-Double vertical protein system
2-Gel Dimension :
8.2x8.5cm
3-Notched plate
4-Plates with 0.75mm, 1mm, and 1.5 mm spacers.
5-Wedge shaped plates
6-Comb 11 wells-1mm and 1.5 mm thickness
7-Comb 15 wells-1mm and 1.5mm thickness 8-Gel
9-Electrod
8) UV transilluminator
1No.
Specification :-Type :Benchtop
-variable wavelength (254/302/365)
Filter glass
light source; 8W
-filter size:-20x20cm
-unit size:~30x33x10 cm(WxlxH)
9) Vacuum Pump
1No.
Specification :-Vacuum :585mm/23”Hg
-Pressure: 4 bar /58 psi
-Power source:1/3HP, 220V/50 Hz motor
-Dimension :LWH-(235x145x280mm)
-Body and head : aluminium make
-Pump Weight approx 8 kgs
10) Microcentrifuge
1 No.
Specification :•
•
Speed:1,000-14,000RPM
Digital display of time & RPM
•
•
•
•
•
Timer: 1 to 60 min or continuous
Standard 6 place rotor for 1.5ml tubes
Spare 12 place rotor for 0.5ml tubes
Power:230V/50 Hz
Non refrigerated
11) Single Channel Pipettes - 1 Set( 3 Pipettes)
Specification :1-Single Variable channel Pipette.
2-Authorization from original equipment manufacturer.
Pipette capacity and their respective systematic error and Random error should not be more than
following using sanders tips.
Adjustable single volume
1-0.5-10µl
1 µl
Systematic error ±2.5%
Random error <_1.8%
5 µl
Systematic error 1.5%
Random error <_0.8%
10 µl
Systematic error 1.0%
Random error <_0.4%
2-2.0-20 µl
2 µl
Systematic error ±5%
Random error <_1.5%
10 µl
Systematic error± 1.2%
Random error <_0.6%
20 µl
Systematic error ±1.0%
Random error <_0.3%
3-100-1,000 µl
100 µl
Systematic error ±3.0%
Random error <_0.6%
5 00µl
Systematic error ±1.0%
Random error <_0.2%
1000µl
Systematic error ±0.6%
Random error <_0.2%
4-Lower body Autoclavable
5-Should reduced pipettes force
6Should have ceramic piston.
7-Should have IVD conformity.
8-Should have single hand two button operation.
9-Should be calibration free for ISO 8655 conform.
10-Should have 4 digit volume display
11-Should be chemical, mechanical, thermal resistance material
12-Authorization from original manufacturer.
12)
Description of Articles (with full specifications giving
below:-)
Hot Plate Magnetic Stirrer
Quantity required
One
• Light weight , Microprocessor based Hot Plate Magnetic
Stirrer
• Capacity-2 liters
• Digital speed control: speed in range of 0-1000rpm
• Plate size (mm)- 130x130
• Made up of steel
• Press-key designed stirrer to adjust speed
• Timer for long time
• Indicator display for motor speed.
• Automatic Temperature control
• With accuracy of 10C.
• Accessories needed stir bar, temperature probe.
13)
Description of Articles (with full
Quantity required
specifications giving)
One
Immunoblot /Semi Dry Blotter
Specifications
• Transfer time should be minimum with least
buffer consumption
• Can be used for western, southern and
northern blotting
• Uniform heart dispersion
• Electrodes with longer durability
• Can work with max. voltage of 600V and
current 200mA
• Size in the range of 250 x 250 x 100 (mm)
• One year warranty
14)
Description of Articles
Quantity required
(with full specifications
giving)
1- single channel pipette set One set
Adjustable volume micropipettes (Single Channel Micro pipette 0.1- 2µL Micro pipette 110-100µL micro pipette 100-1000 µL equipped with a precision setting mechanism, the line
is continuously adjustable down to a very fine volume resolution. Single-handed volume
setting easy when other hand busy. Click stops, together with freely rotating Smarty plunger
button cap secure setting stability while pipetting
Minimum maintenance/ sterilisation shock, heat, chemicals and UV light resistance is
provided by carefully selected materials and good construction. Consequently, maintenance
requirements are close to inexistent. Thorough cleaning and sterilisation can be achieved by
autoclaving the instrument fully assembled (1210C/2500F-20 minutes).
Vol/ µL Div. µL Min.
Mid
Max.
Min
Mid.
Max.
Tip
0.1-2
0.002
1-10
10-100
0.01
0.1
1001000
1
vol.
<±6.0%
1)
<±2.5%
<±1.5%
vol.
<±
4.0%
<±.8%
<±1.2%
<±
1.5%
<±
1.0%
vol.
<±2.0%
vol.
<5.0%1
Vol.
<3.3%
vol.
<1.5%
<±1.0%
<±
0.8%
<±0.5%
<2.5%
<1.0%
<1.6%
<0.6%
<0.7%
<0.2%
<0.5%
<0.4%
<0.2%
15)
Description of Articles (with full
specifications giving)
Quantity required
1- water bath
One
Temp. range: Ambient +5 to 100
Temp. accuracy: ±0.1
Temp. control: PID controller
Temp. Display: LED digital display
Volume: 10 litre
Inner dimensions:
295X235X150mm
Overall dimensions:
340X280X305mm
Weight (approx): 7kg.
16)
Description of Articles (with full
specifications giving)
Quantity required
1- Microwave oven
One
17)
Quantity required
Description of Articles (with full
specifications giving)
1. -200C Deep freeze
One
Dimensions
Height: 905mm
Depth:600mm
Width:920mm
Capacity:265 Litre
Baskets: 2 (3MAX)
Temperature range:- 18-240C
Warranty- 3yrs-labour
18)
Description of Articles (with full
specifications giving)
Quantity required
1- pH Meter
One
•
Microprocessor based with high
performance digital circuit and CPU.
style
Ultra 10
µL
200 µL
200 µL
1000
µL
Multi-point push-button calibration
Auto-buffer recognition
Viewing of electrode slope and
offset value
Automatictemperature compensation
large custom LCD display
Supplied with pH electrode with
holder, pH buffers, power adapters
pH range 0.00~14.00pH accuracy
±0.05; pH resolution 0.01; pH mV
Range 0~±1999mV mV; Accuracy
±2mV; pH Calibration points 2
Points;
temp.
Compensation
0
0~100 C (manual); power source
DC9V,
AC
220V
(50Hz);
Dimensions
210x205x65(mm);
weight 1.5kg
•
•
•
•
•
•
19)
Description of Articles (with full
specifications giving)
1-Multichannel
micropipettes,
12 channel 20-200 µL
Quantity required
One
Inaccuracy (Rel. err.%)- µL 20-200;
div. µL 0.2; Min. vol. <± 0.9%; Mid.
Vol. <± 0.8%; Max. vol. <± 0.7%
Imprecision (CV %)- Min. vol. <0.6%;
Mid vol. < 0.5%; Max.vol. <0.3%; tip
style 200 µL
20)
Description of Articles (with full
specifications giving)
Quantity required
1- Vertical gel electrophoresis One
No. of gels; 1-4; gel type: hand cast gel
of precast gel; glass plate; long glass
plate with spacer and short glass plate;
glass size: long 101X82 (mm); short:
101X73(mm); gel size: hand cast gel;
83X73(mm);
ready
cast
gel:
86X86(mm); buffer volume : for running
two gels: 700 ml buffer volume : for
running four gels: about 1000ml; running
time for SDS- PAGE:35-45 min (at
constant
voltage200v);dimension:
120X160X180(mm); weight: about 1kg.
Full scale accessory support including
gel casting stand, casting frame, glass
plates, combs and gel spades.
21)
Description of Articles (with full
specifications giving)
1- electronic
weighting balance
Quantity required
One
Capacity: 2000gm; Readability: 0.05gm;
repeatability: 0.05gm; linearity± 0.1gm;
Pan size: 12.7cm dia); calibration:
external,
with
calibration
mass;
automatic shut off; yes; weighing units:
g,ct,lb,oz,d,gn,ozt,dwt; output; built in
RS-232 interface; stability indicator: yes;
housing size (WXHXD) 19.7x7.3x24.8
cm; power : 220VAC
22)
Description of Articles (with full
specifications giving)
Quantity required
One
1- multichannel pipette
Specification :
1. 8-channel pipette
2. Capacity : 10-100NL
3. Precision : ≤2.0%-≤0.3%
4. Accuracy: ±3.0% to ±0.8%
5. Should have single rand two button
operation
6. Should have 4 digit volume display
SPECIFICATION FOR MULTICHANNEL PIPETTE
• 8-channel pipette.
• Capacity 10-100 µL
• Systematic error and Random error should not be more than following using standard tips.
10 µL
50 µL
100 µL
Systematic error ±3.0%
Systematic error ±1.0%
Systematic error ±0.8%
Random error ≤ 2.0%
Random error ≤ 0.8%
Random error ≤ 0.3%
• Lower body autoclavable.
• Should reduced pipetting force.
• Should have ceramic piston.
• Should have IVD conformity.
• Should have single hand two button operation.
• Should be calibration free for ISO 8655 conform.
• Should have 4 digit volume display.
• Should be chemical, mechanical, thermal resistance material.
23)
Description of Articles (with full
specifications giving)
Single Channel Pipette Set
1- 0.1-2.5ml
2- 0.5-10ml
3- 20-200ml
4- 100-1000ml
1)0.1-2.5 µL
For use with 10 µL pipette tips
Inaccuracy: ±12.0%-±1.4%
Imprecision:≤ 6.0%-≤0.7%
2.)0.5-10 µL
Quantity required
One set
For use with 10 µL pipette tips
Inaccuracy: ±2.5%-±1.0%
Imprecision:≤ 1.8%-≤0.4%
3.)20-200 µL
For use with 200 µL pipette tips
Inaccuracy: ±2.5%-±0.6%
Imprecision:≤ 0.7%-≤0.2%
4).100-1,000 µL
For use with 1,000 µL pipette tips
Inaccuracy: ±3.0%-±0.6%
Imprecision:≤ 0.6%-≤0.2%
Two-button operation
Autoclavable lower part
TUV award: ergonomic, user-friendly and user-tested
Viable calibration seal indicates factory calibration has not been changed
Chemically resistant
Reduced operation forces
Single-handed operation
4-digit display
Maintenance-free nose cones
At least three-year warranty
•
•
•
•
•
•
•
•
•
•
24)
Description of articles (full)
UV transillminator
Quantity
One
Specification
• UV source: 4x8 W UV
tube
• Klave length: 365nm
• Input: 220V AC
• (specification detail )
SPECIFICATION FOR UV TRANSILLUMINATOR
•
•
•
•
•
UV source with long wave length of 365nm.
4x8 watts of 365nm
4x8 watts of 254 nm UV tubes & 4x8 watts of 365 nm UV tubes with safety fuse.
Viewing area of at least 20x14cm
Input Voltage: 230V, 50Hz, A.C. supply
25)
Description of articles (full)
Quantity
Microwave oven
specification attached
One
Specification for Microwave oven -01
•
•
•
•
•
Approx 30 litre capacity
Convection Microware
Convection heat source
1,400 Watts/1,250 Watts Power Consumption
230V.50Hz
•
•
900 W output power
LED Bar
26)
Description of articles (full)
Rocking unit
(specifications are enclosed)
Rocking shaker (specifications)-01
1234-
Quantity
One
rocking shaking unit with a platform dimension of minimum of 30cmx30cm
shaking speed range within 10-100 rpm with good time range
loading capacity in the range 5-10 kg
should accommodate different type of vessels
27)
Description of articles (full)
Quantity
PH meter
One
(specifications are enclosed)
Digital pH meter (specifications)
•
•
•
•
•
•
pH range 0.00~14.00pH
pH accuracy ±0.05 pH
resolution 0.01 pH
pH calibration points 2 points
Temp. compensation 0~100ºC (manual)
Power source DC9V, AC 220V (50Hz)
28)
Description of articles (full)
Spinot magnetic stirrer
Quantity
One
(specifications are enclosed)
Spinot magnetic stirrer (specifications)
1234-
2 hot plate with a dimension of minimum of 15x15 cm made of ceramic material
Temperature range of 100-150º C
Speed range of 100-500 rpm
Capacity in the range of 500-1000ml
29)
Description of articles (full)
Micro centrifuge (specifications
are enclosed)
Micro centrifuge
Non-refrigerated Microfuge- specifications
•
•
•
Speed: 1,000-13,000 RPM
Digital display of time& RPM
Timer: 1 to 60 min or continuous
Quantity
One
•
•
•
Standard 6 place rotor for 1.5ml tubes
Spare 12 place rotor for 0.5ml tubes
Power: 230V/50Hz
30)
Description of articles (full)
Micropipette- single channel (1 set)
(specifications are enclosed)
Quantity
One set
Micropipette- single channel (specifications)- 01 set
Adjustable, autoclavable single channel pipettes in the ranges of
1- 0.1-2.5 µLsingle channel pipette with an accuracy of 0.02 and increment of 0.1µL
2- 2-10 µL single channel pipette with an accuracy of 0.02 and increment of 0.5µL
3- 20-200 µL single channel pipette with an accuracy of 0.1 and increment of 1µL1001000 µL single channel pipette with an accuracy of 1 and increment of 1µL
Warranty of the materials for minimum of 1 year
31)
Description of articles (full)
Quantity
One
Multi channel pipette
(specifications are enclosed)
Multi channel pipette-01
Specifications for Multichannel pipette
• Multichannel-8 channel pipette (30-300 µL)
• Authorization from original equipment manufacturer.
• Pipette capacity and their systemic error should not be more than ±0.6% and Random
error should not be more ≤0.3%
• Lower body autoclavable
• Should reduced pipetting force
• Should have ceramic piston.
• Should have IVD conformity.
• Should have single hand two button operation.
• Should be calibration free for ISO 8655 conform
• Should have 4 digit volume display
• Should be chemical, mechanical, thermal resistance material
32)
Description of articles (full)
Quantity
Out door digital Camera min 14
mega pixel min. 10x200m
One
33)
Description of articles (full)
Digital Handy cam
34)
Description of articles (full)
Quantity
One
Quantity
Ergonomically Designed officer
chairs with arm-support/rest
,flexible back
35)
Description of articles (full)
Quantity
One
Mixer & feed grinder
36)
Description of articles (full)
Electronic balance
digital scale Capacity 5kg (metallic body)
4
Quantity
One
37)
Description of articles (full)
Quantity
4
Infrared thermometer
38)
Description of articles (full)
Quantity
Printer laser/Inkjet
One
39)
Description of articles (full)
Torch screen display
(Scroller)
Quantity
One
40)
Description of articles (full)
Micropipette Single Channel
Pipettes
Specification
41)
Description of articles (full)
High precision electronic balance
Quantity
1 Set
0.5-10ml-1
10-10ml-1
100-1000ml-1
0.1-2ml- 1
Quantity
1 Set
Specification
Capacity
Per size
200g
80-100mm
0.001g
±0.2g
±0.002g
Readability
Repeatability
Linearity
42)
Description of articles (full)
Quantity
01
Autoclave Vertical
Specification:Inner clamber jacket boiler made of stainless steel.
Outer body made of white stove enamelled mild steel,
Fitted with on/off switch, pressure gauge, steam
release value ,indicating light ,safety value ,water level
& steam release cock to work on 220 volt, complete
with stainless steel basket working TempRange
:121ºC,
Volume:Approx x95liter,Diamension:
600mmx450Dia. Along with accessorises viz 4
heating element :4 rubber gasket;2 automatic low
water cut off devices ;1.Microprocessor based Digital
Temperature Indicator cum controller with inbuilt
Timer & alarm system.
43)
Description of articles (full)
Elisa Reader
Specification :Plate format
Reading Principal
Filter wavelength
Band within
Accuracy
Light Source
Temperature Range
Humidity Range
Readout range
Display
Interface
Dimension
Weight
Power supply
Software included
Quantity
01
96 –well plate
8 channel
bichromatic reading
405,450,492,630nm
8 mm
± 2 nm
Monochromatic
LED
10ºCto 35ºC
15%-85%
0.000-4.000Abs
7”TFT
LCD,800x480pixels
RS-232,4 USB
ports, SD card
400x310x169mm
6kg
100-240V,50/60Hz
44)
Description of articles (full)
Quantity
Hot air Oven
01
Specification:Inner chamber made of stainless steel. Outer body made of
Mild steel with powder coated with pure glass wool
insulation between the walls. Supplied with 2-3 multi
position wire frame shelves. Covered Heaters placed under
ribs at the bottom and sides to give equal and uniform
distribution of heat Temperature is controller by sensitive
bimetal thermostat up to 250ºC,provided with L shaped
thermometer ,3 heat switch , pilot lamps to work on 220
VAC, complete with connecting cord and plug. Working
Temp Range:Up to 250ºC accuracy ; +1º C, Dimension
:600mmx600x600mm with additional 4 air Circulation
fans.
45)
Description of articles (full)
Tissue homogenizer
Quantity
One
Speciation :1-Should have powerful 125 watt motor with 5 mm probe.
2-Should have light weight ergonomic design.
3-Should have quilt operation under 72 db.
4- Should have ¼ turn bayonet probe mounting system for fast release.
5-Should have variable speed control from 5,000 to 35,000 rpm.
6-Sould be CE approved.
7-Should have 1 year warranty.
8-Should have 12 plastic probe and 1 stainless steel probe.
9- Should have authorization certificates.
46)
Description of articles (full)
Submarine gel electrophoresis
system with power pack and
accessories
Quantity
01
Specification :Gel dimension :-120x120/120x60/60x120/60x60(mm)
Runs up to-2,3,8,18,6,13,11or 25 samples.
Comb thickness:-1.0/1.5/2.0mm
Buffer volume: about 600 ml
Size (lxWxD):310x150x90mm
Weight :-around 1 kg.
With 300V power supply: 300V maximum voltage for MP 300V
700mA maximum current.
150W maximum power
Four pairs of outlet terminal.
Timer with alarm function
Constant voltage or constant current operation
Advanced safety device design.
47)
Description of articles (full)
Ultra low Deep Freezer (-80ºC)
Quantity
2
Specification:• Fully programmable microprocessor controlled vertical stackable freezers with
individual capacity of at least 100 L & individual temperature range from -50ºCto
-86ºC with 1ºC increment.
• Eye level control panel, construction should be of Ultra thin Vacuum insulation
panel.
• System should have high grade stainless steel interior and tough, power coated
exterior finish constructed on steel gauge.
• Stackable Freezer should have at least 2 compartment each with inner doors to hold at
least 6 racks & 60 boxes of 2” per Freezer, heated air vent and front panel air filter,
Heavy duty lockable castors and lockable outer doors and lids, battery back up.
• 4 PIN security lock for unauthorized tampering.
• Audible and visible alarms for temperature, power failure, system failure, battery low
etc. and it should also have remote alarm port for connection to an auto dealer.
• Use CFC-FREE, HCFC-FREE non-flammable refrigerants, and refrigeration system
must be energy efficient and hermetically sealed cascade refrigeration system.
• Compressor should be capable to run any voltage between 190-270V. Freezer must
have ISO 9001 standard quality test requirements and IEC 61010 Electrical safety CE
& UL certified.
• Insulation panel should be warranted for more than 10 years and compressor should
be warranted for 5 years.
• Freezer should be supplied with 3 KVA voltage stabilizer.
• User list essential.
48)
Description of articles (full)
Gel documentation system
Quantity
01
Specification :High resolution 12 bit CCD camera; Real time live
imaging for easy image setting & focusing; 5-45mm Zoom
lens; Motorized exposure control; View port with UV
blocking shield for protected samples viewing during UV;
excitation to allow for visualization of gel and
confirmation of bands UV excitation ; Multi Broad Band,
Dual wavelength, Dual Intensity UV trans- Illuminator;
Epi white light illumination for optimized focusing;
Software for –Multicolour Fluorescence Microscopy
Imaging. High density Array, Microtiter plate, Elispot &
dot Blot analysis, Automatic Colony, Cell & GPF Yeast
counting, molecular Weight /Rf value calculation, ID
Multilane Densitometry, Auto lane & band detection with
manual override /editing, detection, Peak & Pattern
comparison , 2D Spot Densitometry ( Quantification)
49)
Description of articles (full)
Tissue processor /homogenize
Quantity
01
Specification :Handheld or post mountable, easy to clean and disassemble
1-For processing samples ranging from 0.25to 30 ml, 2-lightweigth ; 3-With a
powerful 125 –watt motor; ideal for most tissue samples; powered by a
rechargeable battery; providing speeds from 5000 to 35,000rpm
and are extremely quite-under 72 dB
Complete with battery, charger, and 7 mm generator probe.
50)
Description of Article
QUANTITY
Thermal Cycler
1
Specifications of Thermal Cycler:
1) It should have universal block for 96 * 0.2ml PCR tubes.
2) It should be gradient PCR with provision of interchangeable block with maximum heating
rate of at least 3º C/ sec.
3) Block temperature range should range between 4º C -100ºC with block uniformity at 55ºC
of less than ±0.3ºC and temp. accuracy at 55ºC of less than ±0.25ºC.
4) Max. & min. gradient in range of 29ºC (19ºC for 384) and 1ºC respectively.
5) Heating and cooling via peltier technology of 8 peltier element/block.
6) Selectable heated lid temperature: 100ºC to 115ºC Cor off.
7) It should have provision of adjustable heated lid pressure.
8) It should have a large colour VGA touch screen (>5 inches) with easy graphical display.
9) Clear run time display for better view from distance, instrument status showing the cycle.
10) System memory of more than 1000 programs.
11) Data transfer through USB port.
12) The dimensions of instrument should be 240L * 240 H mm.
13) Have the provision of auto restart.
14) Works at power supply of 100-230V, 50-60 Hz.
15) Light weight upto 10 kg.
16) 3 year warranty.
17) Last 2 years users list.
51)
Description of Article
Quantity.
Inverted trinocular microscope with digital camera
and computer printer as per the specifications.
1
SPECIFICATIONS :S.NO.
COMPONENTS
MINIMUM SPECIFICATIONS
1
Optical System
Infinity corrected system, 45 mm parfocality distance. Field
of view 22 mm.
2
Head
Trinocular: 45º inclined, Interpupillary distance: 55-75 mm.
Adjustable dioptric compensation.
3
Eyepieces
Extra wide field 10 * 22 mm, high point.
4
Nosepiece
5 position, with bidirectional rotation on ball bearings and
click stop.
5
Objectives
Long working distance (LWD), infinity corrected (IOS) plan
achromatic: phase contrast 10 * 0.25 (working distance 7.94
mm), phase contrast 20 *0.40 (working distance 7.66mm),
phase contrast 40 * 0.60 ( working distance 3.71 mm) ,
corrected for .2 mm cover glass.
6
Specimen stage
Size: 250 * 230 mm. translator with lower ergonomic coaxial
controls. X-Y translation:114 * 81mm. interchangeable
metallic inserts for specimen slides, Petri dishes and flasks.
7
Focusing system
Macro & micro metric regulation, with coaxial knobs on
both sides of the stand adjustable system
8
Condenser
Long working distance condenser, numeric aperture 0.30,
working distance 72mm. The condenser can be removed in
order to increase the working distance to 150 mm.
9
Illumination
X-LED 8TM system, with adjustable intensity, filter and
phase ring holder and aperture diaphragm
System
10
Desktop Computer
From a reputed brand, with the following specs.-
With printer
-
11
C-mount camera
With software
Package
Intel ore 2 duo CPU I/3/!5 processor.
RAM- 4 GB
128 bit operating system
18” LCD monitor with keyboard & mouse (optical)
1KVA UPS
Built in DVD writer
All in one laser printer
Resolution: 3.2 Mpixel, sensor: Cmos ½.5”, pixel size
3.2µmm, imaging area: 6.5 mm * 4.92 mm, frame rate at
full resolution: 6 frames/sec, optical sensitivity: 1.0
V/lux/sec, dynamic range:61dB etc.
52)
Description of article
Quantity
Shaker Incubator
01
Specification of shaker Incubator:Chamber volume
Temp.
115 L
Heating
Forced Convection
Type
Range
Ambient +5ºC  60ºC without cooling System
10ºC  60ºC with cooling system
Accuracy
±0.1ºC at 25ºC
Uniformity
±1.0ºC at 25ºC
Shaking speed/
60-300rpm/20mm orbital motion
Stroke
Main controller
Digital PID controller with timer and auto tuning
Wait off timer
Mm:ss/hh:ss continuous selectable
Sensor
Pt. 100 Q
Safety Device
Temp.
Hydraulic over temp. protection safety device
Electrical
Electrical leakage breaker
Dimension
Chamber – 550 * 585 * 360
(W*D*H) mm
Overall --- 765 * 640 * 770
Platform -- 500 W * 510 D
material
Internal – Stainless steel 0.8T polished ( SUS304)
External-- Steel 1T with Epoxy powder coating
Door-- Weight balanced door with transparent acrylic
window
Utility
Lamp—25 Watt crypton lamp in chamber
53)
Description of article
Quantity
Spectrophometer
1
Specification of Spectrophometer:Wavelength range
190mm- 1100mm
Spectral bandwidth
2.0 nm
Resolution
2nm
Stray light
0.2%T (220nm & 340nm)
Wavelength Accuracy
0.5nm (with automatic wavelength correction)
Wavelength
0.2nm
Reproducibility
Photometric
Double beam monitoring ratio system
System
Photometric method
Transmittance, absorbance, energy, concentration
Photometric range
-0.3  3.0 Abs (0  200%tT)
Photometric
0.002 Abs (O  0.5 abs), 0.004 Abs (0.5  1.0 Abs)
Accuracy
± 0.3%T (0-100%T)
Photometric
0.01 Abs (0 0.5 Abs) , 0/002 Abs (0.5  1.0 Abs)
0.15%T(0  100%T)
Reproducibility
Photometric Display
-9999 ----9999
Photometric noise
< ±0.001 Abs (500nm, 0Abs, 2nm bandwidth)
Scanning speed
1400nm/min
Baseline flatness
0.002 Abs (190nm-1100nm)
Baseline stability
0.002 Abs/h(500nm, after preheating)
Slew rate of
3600nm/min
Wavelength
DNA/RND
measurement
Results printout: Printing of measured data by using any
printer with parallel port connection available.
Mainframe
Compact & standalone spectrophotometer mainframe
Light source
Socket deuterium lamp & socket
Tungsten halogen lamp
Detector
Double beam
Sample chamber
2 cell holder
Display
Liquid crystal Display( LCD 320 I A240 dot matrix)
Keypad
Touch soft keys
PC interface
PC interface : RS-232
54)
Rabbits cages , mice cages etc
S.No
Description Of item
Dimension
Quantity
1
Rabbit cage standard.
24” * 18” * 18”
17
Stainless steel
2
Rabbit cage breeding
48” * 18” *18”
03
3
Rabbit cage trolley std.
24” * 18” *18”
04
4
Rabbit cage trolley
48” * 18” *18”
01
29*22*12 cm
05
breeding
5
Mice cage trolley
6
Ear punch
7
Mice food hopper
Capacity -100g
100
8
Mice and rabbit holder
14” * 6” * 7”
02
01
15-30g
Specifications:Cage Size: 24” * 18” * 18” (L * B * H) (adults /std cage).
1
Fabricated from good quality stainless steel
wire of uniform thickness ( AISIS. S 304 quality material).
Cage size: 48” * 18” *18” (nursing /breeding cage).
2
Including central cage partition for separation of nursing mother. To be fabricated as above.
3
4
Racks/trolley for rabbit to hold 6 cages of size 24” * 18” * 18”. Supplied along with tray for
collection of excreta, individual feeder and waterier. Made up of corrosion resistant material
like good quality steel.
Racks/trolley for rabbit to hold 3 rabbit breeding cages of size 48” * 18” *18”. Supplied along
with tray for collection of excreta, individual feeder and waterier. Made up of corrosion
resistant material like good quality steel.
5
Ear punch
6
Rabbit holder of size 14” * 6” * 7”
Racks/trolley for mice cages to hold 24 mice cages of 29 * 22 * 12 .
7
8
9
(i)
Fabricated from durable 1” squire hollow pipe/angle of stainless steel of good
quality (AISI S.S 304 quality material).
(ii)
The racks should be provided with adjustment facility and wheels at base for easy
shifting.
Food hopper for mice with capacity of 100gms
Mice holder (15-30gm weight) made up of entirely clear see-thru acrylic plastic with mechanism
to adjust the length of the chamber with turn of a knob
55)
Desription of article
Quantity
Refrigerated Centrifuge
1
High speed
Specifications of refrigerated centrifuge:Centrifuge should be able to work in a wide temp. range of -11ºC to +40ºC and have a fast
cooling function
1
Must have a standby cooling and heating mode up to 8 hrs which enables cooling or heating
even when not in operation.
2
Must have automatic temp. start up at a specific time to automatically prepare temp. before
centrifugation.
3
Must be able to maintain at 4ºC at max. speed.
4
Max speed of 17500 rpm, max rcf of 30,130 g adjustable from 100 rpm upwards in an
increment of 10 rpm up to 3000 rpm and in an increment of 100 rpm thereafter.
5
Acceleration time to max. speed must be less than 14s for all rotors at max load and a
deceleration time of less than 15s with the standard 30 X 1.5/2ml rotor, but has option to
6
accelerate and decelerate gently for sensitive samples using SOFT function.
7
Timer for run can be set for 99 min continuous
8
Choice of 7 fixed angle rotors and 1 swing out rotors should be available
Should be supplied with following rotors:-
10
- A fixed angle rotor accommodating 24 X 1.5/2ml tubes with 30000xg
- Fixed angle rotor accommodating 6 X 15/50ml with 7000xg
- Swing-bucket plate rotor accommodating 2 X DWP or MTP not higher than 29 mm
- Fixed angle rotor accommodating 8 X 80PCR strips
Should be supplied with 3 yrs warranty
11
Last one yrs users list
12
Services as and when required
9